MSC ENGINEERING PACKAGE

EP No: ECR-19-000793 Rev 00

EP Title: 6092E Convert 90 Day Storage Pad Prop to Storage Building

Document Action Only Physical Modification

1.0 PACKAGE DESCRIPTION RELEASE Radiological Record

Request and Justification:

Enclose 6092E 90 day storage pad, add several doors, and bring power to building.

Work Package No/Project No:

N/A

Area:600

Facility:N/A

Building:6092E

System ID:N/A

Release

Work Complete Field Work Complete

Design Authority

Change Description and Scope:

In all drawing titles/drawing references/nameplates, replace "6092E 90 Day Storage Pad" with "6092E Storage Building". Upon work competition of this ECR, building 6092E shall be named "6092E Storage building". The following ECR shall call it as such.

In 6092E, remove the interior metal partition wall separating room 101 and 102, all exterior grade plywood, the crane, crane rail, and the chain link fence surrounding 6092E. Remove the 6" curb separating Rooms 101 and 102, two bollards, and reconfigure concrete to extend the ramp as shown in SK-003.

Build and install a new wall to cover the south wall of 6092E with the materials specified in SK-001. Install a new 3' by 7' personnel door in the approximate location shown in SK-001. Anchor the doorjamb to concrete slab with 1/2" Hilti expansion bolts. Install two 8' wide by 10' tall insulated roll-up doors in accordance with SK-001. Insulate all walls and ceiling with R-30 min. insulation. Seal all edges and penetrations with the manufacturers installation instructions. Install 1/2" plywood on all interior walls of room 101 and 102 up to 8'-0" height.

Install a new 30A 480V MCC breaker inside Prop/Pad Power Supply Panel "6092E Storage Building". Install one new 10 KVA mini power zone SquareD model # MPZ10S40F or engineering approved equivalent in the southeast corner of building 6092E. Label the new Mini Power Zone as "LP-6092E". Field route one new 1" minimum PVC schedule 80 conduit between 6092E and the Prop/Pad Power Supply Panel "6092E Storage Building" running minimum 3#8 THWN-2 conductors and 1#10 copper ground. In "LP-6092E", add six new 20A single pole breakers SquareD model # QO120 or engineering approved equivalent. Install a GFCI heavy duty NEMA 3R rated receptacle next to the MPZ. Install five receptacles (three wall mounted, two ceiling mounted) in the approximate locations shown in SK-002. Install three LED lighting fixtures in the ceiling in the approximate location shown in SK-002. Lighting fixtures shall be Lithonia Lighting model # FEM L48 4000LM IMACD MVOLT 40K or engineering approved equivalent. For each garage door, install 1/2 hp. garage door opener. For all new lights/receptacles installed, field route minimum 1/2" EMT conduit running minimum 12 AWG THHN conductors and ground.

In "LP-6092E", install two new 15A two pole breakers SquareD model #QO215 or engineering approved equivalent. Install two 2000 watt Trane Model number 021B7A 240V unit heaters (or engineering approved equivalent) in the approximate location shown in SK-002. Field route minimum 1/2" EMT conduit running minimum 12 AWG THHN conductors and ground.

ECR-19-000793 00 1 of 30

DATE:

Aug 21, 2019

2.0 PACKAGE INDEX

Action Document No. Rev. No. E/S/R Section Description Page No. Release to Work?

I SK-001 - - Enclose 6092E Storage Building Yes

I SK-002 - - Power Plan Yes

I SK-003 - - Concrete Demo/Reconfiguration Plan Yes

RWC H-6-13481 001 2 - DWG-001 Yes

RWC H-6-13498 001 9 S DWG-002 Yes

RWC H-6-13503 001 8 S DWG-003 Yes

RWC H-6-13511 001 10 S DWG-004 Yes

RWC H-6-13516 001 10 E DWG-005 Yes

RWC H-6-13517 001 14 E DWG-006, DWG-007 Yes

RWC H-6-13518 001 2 - DWG-008 Yes

RWC H-6-13525 001 1 - DWG-009, DWG-010 Yes

RWC H-6-13526 001 1 - DWG-011, DWG-012 Yes

RWC H-6-13527 001 1 - DWG-013, DWG-014 Yes

RWC H-6-13528 001 1 - DWG-015, DWG-016 Yes

RWC H-6-13529 001 1 S DWG-017 Yes

RWC H-6-13572 001 3 - DWG-018 Yes

RWC H-6-13629 007 1 E DWG-019 Yes

RWC H-6-13636 001 6 - DWG-020 Yes

I INFO-001 - - Heater Calculation Yes

3.0 DESIGN REQUIREMENTS

Electrical modifications shall be in compliance with NFPA 70, National Electrical Code, 2017 Edition. All electrical components shall be approved by a National Recognized Testing Laboratory (NRTL).

Drawings shall be in compliance with MSC-PRO-ENG-709, Rev. 2 - CAD and Drawing Development and Control Process for Engineering Drawings.

4.0 ACCEPTANCE CRITERIA and METHODS

Acceptance Criteria Acceptance Method

Installation approval by NEC inspector is required prior to energization of new and modified electrical equipment. Inspection Testing

Test wiring for continuity and unintentional grounds prior to energization and document in work package. Inspection Testing

Verify all modified equipment is labeled correctly. Inspection Testing

Verify that new panel schedules are posted as shown in DWG-018. Inspection Testing

5.0 OTHER AFFECTED DOCUMENTS

Document Type Document No. Rev. No. Owning Organization Technical Authority

N/A N/A N/A N/A N/A

ECR-19-000793 00 2 of 30

5

6

78

9

10

1112

13,1415

16,17

18,19

20,2122,2324

2526

27

28-30

Verification by: Peer Review Formal Design Review Alternate Calculations Qualification Testing

6.0 DESIGN VERIFICATION

Design Verification Checklist:

a. Are the Functional Requirements and Design Criteria appropriately selected for the modification? Yes No NA

b. Does the design meet the specified Functional Requirements and Design Criteria? Yes No NA

c. Were the design inputs correctly incorporated into the design? Yes No NA

d. Is the design output reasonable compared to the design inputs? Yes No NA

e. Have suitable materials, parts, and processes been specified? Yes No NA

f. Have suitable acceptance, inspection, and operability been adequately addressed in the change? Yes No NA

g. Have constructability, maintenance, and operability been adequately addressed in the design? Yes No NA

h. Are all affected design documents identified and appropriately changed? Yes No NA

Additional Design Verification Documents Prepared? Yes No

NOTE: Identify additional Design Verification Documentation in Section 2.0 Package Index.

A review of the design has been performed. The selected Functional Requirements and Design Criteria meet the stated Engineering Request. Design Verification performed by the method(s) identified has confirmed that the design documented by this FMP is adequate and meets the stated Functional Requirements and Design Criteria.

H2945424 - SEAN LEISTRITZ 8/20/2019 2:27:17 PM

Design Verifier:  Print Name Signature    Date

7.0 REVIEWS

USQ: USQ GCX

No: Not Required

H1037518 - SEAN W CARLSON 8/20/2019 2:32:44 PM

Reviewer  Print Name Signature Date

Environmental: Screened Ref: Not Required

ECO  Print Name Signature Date

8.0 APPROVALS and DISTRIBUTION

Approvals

H5046101 - YURIY V DUBINETS 8/20/2019 3:05:57 PM

ECR Author:  Print Name Signature    Date

H1037518 - SEAN W CARLSON 8/20/2019 3:03:24 PM

Design Authority:  Print Name Signature    Date

H7518890 - DREW A THOMAS 8/21/2019 10:50:01 AM

Engineering Manager:  Print Name Signature    Date

H4668590 - DHARMENDRA B RANA 8/20/2019 3:11:34 PM

Title:Civil Engineer   Print Name Signature    Date

ECR-19-000793 00 3 of 30

H0076065 - BRET M AKERS 8/20/2019 4:36:02 PM

Title:Operations Manager  Print Name Signature    Date

Title:  Print Name Signature    Date

Title:  Print Name Signature    Date

Title:  Print Name Signature    Date

Distribution

HID Name

H2945424 SM Leistritz

H1037518 SW Carlson

H7518890 DA Thomas

H4668590 DB Rana

H0076065 BM Akers

ECR-19-000793 00 4 of 30

N/A

N/A

N/A

14'-0"

15'-0"

14'-0"

4'-0" 4'-0"

LINE OF ROOF

OVERHANG ABOVE

FOUNDATION PLAN

(BEFORE)

14'-0"

15'-0"

14'-0"

4'-0" 4'-0"

LINE OF ROOF

OVERHANG ABOVE

FOUNDATION PLAN

(AFTER)

METAL PARTITION

WALL OVER 6" CURB

REMOVE METAL PARTITION

WALL AND 6" CURB

30'-0"

30'-0"

4'-0"

8'-0"

4'-0"

8'-0"

1'-0"

3'-0"

2'-0"

8' W x 10' H

ROLL-UP DOOR

8' W x 10' H

ROLL-UP DOOR

3' W x 7' H

PERSONNEL

DOOR

7'-0"

3'-0"

4'-2"

15'-3"

3'-0" 8'-0" 4'-0" 8'-0" 1'-0" 3'-0"

1'-0"

STRUCTURAL ELEVATION

A-A

30'-0"

2 DOUBLE C - DOOR

HEADER

1 C - DOOR JAM (TYP)

2 DOUBLE C - DOOR

HEADER

3 C - 8" GIRT (TYP)

EXISTING STEEL BEAMS,

COLUMNS, PURLIN

E

EXISTING 6" CONC.

GRADE SLAB

ITEM NO DESCRIPTION MATERIAL SPECIFICATION REMARK

1 DOOR JAM C-8" DEEP X 12 GA GALVANIZED

2 DOOR HEADER DOUBLE C-8" DEEP X 12 GA GALVANIZED

3 GIRT C-8" DEEP X 12 GA GALVANIZED

4 WALL PANEL BR-II 26 GA (BUTLERRIB II) GALVANIZED

26 GA. METAL

WALL PANEL

MATERIAL TAKE OFF

NOTES:

1. REMOVE INTERIOR WALL AND CURB.

2. REMOVE PLYWOOD FROM 3 SIDE WALL.

3. REMOVE CRANE AND CRANE BEAM.

4. ANCHOR THE DOOR JAM TO CONC. SLAB WITH 1/2 " ∅ HILTY EXPANSION BOLT

5. CONNECT ALL GIRT TO STEEL COLUMN/BEAM WITH 3/8" THICK FIELD WELDED

CLIPS.

6. FOR GIRT/COLUMN HEADER CONNECTION - USE 1/2" ∅ A307 BOLTS.

7. FASTEN WALL PANEL WITH WEATHER SEAL SCREW.

A

A

N

PROJECT: ENCLOSE 6092E STORAGE BUILDING PREPARED BY: D. RANA DATE: 11/14/2018 SK-001

5 ROLL-UP DOOR 8' W X 10' H -

5

5

6

6 PERSONNEL DOOR 3' W X 7' H -

ECR-19-000793 00 5 of 30

30'-0"

@ 1:8

6" CURB

(TYP)

CURB

6" HIGH

12'-10"

15'-0"

6"

4'-0"

RAMP

DOWN

6" CURB

30'-0"

@ 1:8

12'-10"

15'-0"

6"

4'-0"

RAMP

DOWN

6" CURB

REMOVE

CURBING AND CREATE A RAMP

RECONFIGURE CONCRETE

6" CURB

REMOVE

21'-0"

CONCRETE DEMO/

RECONFIGURATION PLAN (BEFORE)

CONCRETE DEMO/ RECONFIGURATION

PLAN (AFTER)

CURB

6" HIGH

2 BOLLARDS

REMOVE

FMP SECTION: SK-003

SECTION DESCRIPTION: CONCRETE

DEMO/RECONFIGURATION PLAN

ECR-19-000793 00 7 of 30

N 374569.92

R=30'

R=30'

30'

30'

20'

R=20' TYP.

N0°0'0"W

88.69'

E 1936336.74

4

5

0

B

B

2'

2'

90-DAY

STORAGE

PAD

PROP

N 374599.92

E 1936336.74

20'

N 374569.92

R=30'

R=30'

30'

30'

20'

R=20' TYP.

N0°0'0"W

88.69'

E 1936336.74

4

5

0

B

B

2'

2'

6092E

STORAGE

BUILDING

N 374599.92

E 1936336.74

20'

WAS IS

H-6-13481 SH 1, REV. 2

FMP SECTION: DWG-001

ECR-19-000793 00 8 of 30

N 374493.99

E 1936338.24

MH-F

2"

N 374466.94

E 1936359.23

1

2

"

90 DAY

STORAGE

PAD

GV

4"

SEE NOTE 1

N 374493.99

E 1936361.71

C 443.00

L

PW-V-36

MO 260

MO 259

1 1/2" PW

GV

6H-6-13497

6089

PW-V-150

PW-V-151

PW-V-152

PW-V-153

4"

6"

N 374493.99

E 1936338.24

MH-F

2"

N 374466.94

E 1936359.23

1

2

"

6092E

STORAGE

BUILDING

GV

4"

SEE NOTE 1

N 374493.99

E 1936361.71

C 443.00

L

PW-V-36

MO 260

MO 259

1 1/2" PW

GV

6H-6-13497

6089

PW-V-150

PW-V-151

PW-V-152

PW-V-153

4"

6"

WAS

IS

H-6-13498 SH 1, REV. 9

FMP SECTION: DWG-002

ECR-19-000793 00 9 of 30

P

E

R

IM

E

T

E

R

R

O

A

D

MO 260

6092E

90 DAY

STORAGE

PAD PROP

P

E

R

IM

E

T

E

R

R

O

A

D

MO 260

6092E

STORAGE

BUILDING

WAS IS

H-6-13503 SH 1, REV. 8

FMP SECTION: DWG-003

ECR-19-000793 00 10 of 30

MH2

1

/

400

4

3

13

12

11

3

32

32

PPB#24

CPB#24

31

STORAGEPAD PROP

40

40

90 DAY

J

SIZE

TYPE

6092E

MH2

1

/

400

4

3

13

12

11

3

32

32

PPB#24

CPB#24

31

40

40

6092ESTORAGEBUILDING

J

SIZE

TYPE

6092E

WAS

IS

H-6-13511 SH 1, REV. 10

FMP SECTION: DWG-004

ECR-19-000793 00 11 of 30

ECR-19-000793 00 12 of 30

ECR-19-000793 00 13 of 30

ECR-19-000793 00 14 of 30

ECR-19-000793 00 15 of 30

ECR-19-000793 00 16 of 30

ECR-19-000793 00 17 of 30

ECR-19-000793 00 18 of 30

ECR-19-000793 00 19 of 30

ECR-19-000793 00 20 of 30

ECR-19-000793 00 21 of 30

ECR-19-000793 00 22 of 30

ECR-19-000793 00 23 of 30

ECR-19-000793 00 24 of 30

ECR-19-000793 00 25 of 30

ECR-19-000793 00 26 of 30

ECR-19-000793 00 27 of 30

ECR-19-000793 00 28 of 30

System ChecksumsBy Mission Support Alliance

Unit HeatersSystem - 001

HEATING COIL PEAKCLG SPACE PEAKCOOLING COIL PEAK TEMPERATURESHeating DesignMo/Hr:0 / 0Mo/Hr:0 / 0Mo/Hr:Peaked at Time: Cooling Heating

SADBOADB: 11OADB:0 / 0 / 0OADB/WB/HR:Outside Air: 0.0 125.0Ra Plenum 0.0 50.0ReturnPercentCoil PeakSpace PeakSpace PercentPercentNetPlenumSpace 0.0 50.0Ret/OASens. + Lat. Of TotalTot SensSpace SensOf TotalSensibleOf TotalTotalSens. + Lat 50.00.0

0.00.0Fn MtrTDBtu/h (%)Btu/hBtu/h(%)Btu/h(%)Btu/hBtu/h0.00.0Fn BldTDEnvelope Loads0.00.0Fn Frict0Skylite Solar 0.000000000

0Skylite Cond 0.0000000000Roof Cond 4.21-585-58500000

0.000Glass Solar 00000000Glass/Door Cond 0 0.00000000

AIRFLOWSHeatingCooling

0Wall Cond 12.62-1,755-1,755000000Partition/Door 0.000000000Floor 0.0000000

Sec Fan83.180Infiltration -11,571-11,5710000

0 0MinStop/Rh

100.000Sub Total ==> -13,910-13,91000000

0Return 439

Internal Loads

2700Exhaust

0Lights 0.000000000

0 0Rm Exh

0People 0.000000

00Auxiliary

0Misc 0.0000000000Sub Total ==> 0.000000000

0Ceiling Load 0.0000000000Ventilation Load 0.000000000

Sup. Fan Heat 00

ENGINEERING CKSHeatingCooling

Ret. Fan Heat 000 % OA 0.00.0Duct Heat Pkup 000 0.380.00cfm/ft²

0Ov/Undr Sizing0.0000

0000

0.00cfm/ton

Exhaust Heat0.000

00

0.00ft²/ton-30.910.00Btu/hr·ft²

0No. People0Grand Total ==> 100.00-13,910-13,910100.000100.0000

AREAS HEATING COIL SELECTIONCOOLING COIL SELECTIONTotal Capacity Sens Cap. Coil Airflow Enter DB/WB/HR Leave DB/WB/HR Gross Total Glass Coil Airflow Ent LvgCapacity

ton MBh MBh cfm °F °F gr/lb °F °F gr/lb ft² (%) °F°FcfmMBh

Floor 450 Main Htg -13.9 169 50.0 125.00.0 0.0 0.0 0 0.0 0.0 0.0 0.0 0.0 0.0Main ClgPart 0 Aux Htg 0.0 0.00.000.0 0.0 0.0 0 0.0 0.0 0.0 0.0 0.0 0.0Aux Clg

ExFlr 00.0Preheat 0.0 0.000.0 0.0 0.0 0 0.0 0.0 0.0 0.0 0.0 0.0Opt Vent

Roof 450 0 0Wall 1,350 0 0

Humidif 0.0 0 0.0 0.00.0 0.0TotalOpt Vent 0.0 0.00.00

-13.9Total

Envelope LoadsSkylite SolarSkylite CondRoof CondGlass SolarGlass/Door CondWall CondPartition/DoorFloor

InfiltrationSub Total ==>

LightsPeopleMiscSub Total ==>

Ceiling LoadVentilation Load

Additional Reheat

OA Preheat Diff.

Ov/Undr SizingExhaust Heat

RA Preheat Diff.

Grand Total ==>

Internal Loads

0

00

0.000.000.00

0

Supply Air Leakage

0

Dehumid. Ov Sizing 0 0Adj Air Trans Heat 0 0 0 0 0 Adj Air Trans Heat 0 0 0

Leakage UpsLeakage Dwn

2700InfilAHU VentNom Vent

Main FanTerminal

Adjacent Floor

Diffuser

Supply Air LeakageUnderflr Sup Ht Pkup Underflr Sup Ht Pkup

Adjacent Floor0.00 0.00 0.00 0.00

0 00 0 0

0.000.00

0.00 0.00 0.00 0.00

0 0.000 0.00

000000

00

169169169

000

00

0 0 0

Int Door 0

Ext Door 0 0 0

TRACE® 700 v6.3.4 calculated at 01:40 PM on 08/19/2019Project Name:Dataset Name: Alternative - 1 System Checksums Report Page 1 of 16092E Heater.trc

HEATER CALCULATION INFO-001

ECR-19-000793 00 29 of 30

Heater Calculation INFO-001

Purpose: A heater calculation was performed to determine the size of heater necessary to ensure temperatures inside 6092E Storage Building do not reach temperatures below freezing (32F) during the winter.

Heating Coil Selection:

Main Heating: 13,900 MBh Design Temperature: 50 F

13,900 𝑀𝐵ℎ

3.413= 4072.66 𝐵𝑇𝑈

Total Heater size required to maintain 50F in the building: 4000 BTU.

Heaters Spec’d out:

(2) 2000 watt Trane (Model# 021B7A) 240V unit heaters

Summary of Results:

The (2) 2000 Watt heaters will be able to maintain (during the coldest part of the year) 50 F. We are only required to maintain above freezing. The requirement is met.

Assumptions: 1. Walls and ceiling are insulated with R-30 min. insulation. The ECR insulates the walls; this ECR

assumes the insulation is installed. Software:

1. Description: Software Title: TRACE 700 version xxx HISI Identification Number: Workstation Type: Property Number:

2. Software Installation and Checkout:

Reference or include a copy of the Software Installation and Checkout form for the workstation used.

3. 4. Statement of Valid Software Application:

Brief statement confirming correct application of the particular software to the problem being solved. Brief statement confirming software has been used within its limitations (e.g., comparison of the problem inputs against the software's required range of variables to determine if the problem fits within the software limitations

References: ECR-19-000793.

ECR-19-000793 00 30 of 30