Brushless GoPro Gimbal for DJI Phantom - BRADATECH · Brushless GoPro Gimbal (Phantom) Manual v1.0...

Brushless GoPro Gimbal (Phantom) Manual v1.0

Designs, Images and Content Copyright Aeroxcraft Ltd. 2013 Page 1

Brushless GoPro Gimbal for DJI Phantom

Basic Manual: Attaching and Connecting to the DJI Phantom



Contents

1) Notes 2) Introduction 3) Tools required 4) Kit Contents 5) Installing the power cable 6) Fastening the Gimbal to the Phantom 7) Powering up the gimbal 8) Connecting the Tilt Control Cable

Page 3 4 5 6 7 11 15 16



1) Notes

MAKE SURE THIS KIT IS ASSEMBLED CORRECTLY BEFORE FLIGHT. IF IN DOUBT CONTACT AEROXCRAFT FOR

ASSISTANCE.

This document is a work in progress. Information contained within this document may be incorrect and we

cannot be held responsible for any damage/injuries caused by following the information contained within this

document.

If you are unsure what you are doing get advice from someone who does.

Multirotor helicopters are dangerous. Operate them away from people and property. Be responsible. If in

doubt do not fly.

Always remove propellers from motors before carrying out work on your multirotor helicopter. Failure to do

so can cause serious injury.

It is the owners responsibility to ensure this model is assembled and fitted out correctly and safely. Ensure

that your model is capable of safely and reliably lifting the payload you are asking it to. This model is

dangerous if used in an incorrect manner. Ensure you seek assistance from an experienced flyer if you are

unsure. Do not fly near people, property or highways. Do not fly over people, property or highways. There

may be laws and regulations governing the use of this model in your area, seek advice from your authorities if

you are unsure.

Planning your build and installation is key to building a safe and reliable multi rotor. Make sure all wiring is of

the correct gauge, properly connected, neat and protected from wear/tear and radio/electrical interference.

Make sure all the components you use are suitable for the size and weight of your multi rotor.

Do not over tighten screws.

Use threadlock to ensure screws do not come loose when in use.

Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after

assembly and frequently during use. Do not use unless all components are correctly fitted and adjusted. Do

not use if any parts are missing, damaged or broken.

Assembly is required. Take care when unpacking and assembling; contains small parts and sharp edges.

If you require any replacement parts they are all available from Aeroxcraft. Contact us for details.

Contact details

Email

[email protected]

Website

www.aeroxcraft.com

mailto:[email protected]://www.aeroxcraft.com/



2) Introduction Plug and Play? (Almost!)

This gimbal is primarily designed for the DJI Phantom multirotor. It comes ready configured for use.

It also comes with all the hardware, cables and connectors you need to install it onto your Phantom.

The only extra part that we do not supply is a lever for the 7th channel on the Phantom transmitter.

We are looking into that, in the meantime however they are available elsewhere.

The DJI Phantom comes with a hidden power cable that is behind one of the white grommets on the

underside. The Aeroxcraft GoPro Gimbal comes with a power cable that needs to be joined to the

Phantoms power cable, by soldering or other means. We recommend soldering and covering the

joins with heat shrink tubing. Some heat shrink tubing is also included to make this easier for you.

There are other ways you could join the wires together, but this is up to you. Make sure any joins are

secure and well insulated. If the wires were to short or come apart it could cause your Phantom to 1)

crash, 2) go out of control, 3) start a fire or 4) a combination of items 1-3! All of which are potentially

very dangerous and best avoided.

Tilt Control

You can opt to use the tilt control or not. The tilt control allows you to move the camera up and

down, from looking straight ahead to looking straight down.

Connecting up the tilt control is more involved than simply fitting the gimbal and connecting up the

power. It involves taking apart your Phantom and also changing some of the settings in the Naza

flight controller. The choice is up to you and it can always be done at a later date if you so choose.

Read through this document first and you can make up your own mind.



3) Tools Required

Fitting Gimbal

2.0mm Hex Driver / allen key

Thread lock (recommended)

Joining power cables

Soldering iron

Solder

Heat gun / Hair Dryer

Tilt Control

12mm Spanner (to remove props)

Small Philips screw driver

2.0mm Hex Driver / allen key



4) Kit Contents

Tilt Control Cable

Power Cable

2x M3 x 30mm Screws

2x M3 x 6mm Screws

2x 20mm Spacers

12x Poly Buffers (Spares)

2x 1.6mm Heat Shrink Tubing



5) Installing the Power Cable We recommend carrying out this stage before attaching the gimbal as it is much easier. Please ignore

the fact that the gimbal is in the following pictures.

Before you proceed ensure that there is no battery pack in the Phantom, no power is connected and

the Phantom is not connected to a computer.

The Phantoms Accessory Power Cable is behind one of the white grommets. On our Phantom it was

behind the one in the photo below. If you are careful, the cable will follow out of the hole with the

grommet. Make sure the wire does not pop back inside the Phantom!

Strip 3-5mm of insulation off each cable. Give the bare ends of wire a little twist with your

fingers to neaten them up. Note that red is positive and grey is negative, it is important you

know which is which as connecting the power to the gimbal board the wrong way round will

damage the gimbal board.



When carrying out soldering make sure you protect your eyes and hands. Do it somewhere

well ventilated and away from children.

Using a soldering iron and some solder, tin the ends of the wire. Its a good idea to cover up

any exposed parts of your Phantom to protect it from any spilt solder.

The Aeroxcraft supplied connector and cable should have the ends already tinned with

solder. If they are not then do it now.

Slide the 2 tubes of heat shrink onto the cables.



You should now be able to solder the wires together by holding them together and applying

heat from the soldering iron. Make sure the heat shrink tubing is well from the soldering

iron as the heat will shrink the tubing.

Nice! Just needs some insulation now.



Slide the heat-shrink tubing over the joins. Make sure the joins are in the middle.

Carefully apply some heat to the heat-shrink tubing. The heat shrink only needs 90C (190F)

to start shrinking. In the picture we are using a heat gun on a very low setting. Make sure

you dont burn your fingers, your workbench or melt your Phantom!

OK, thats done. If you are happy with the finished result then you can proceed to attaching

the gimbal to the Phantom.



6) Fastening the Gimbal to the Phantom From the accessory pack you need: 2x Spacers, 2x M3x 30 Screws, 2x M3 x 6 Screws

Note: It is a good idea to apply a small amount of thread lock to the screws so that they

cannot come unscrewed in flight.

Remove the 2 screws from the Phantom Landing gear that are circled green in the picture

below.



Put the M3 x 30mm though the holes in the rear legs of the gimbal mounting plate.

Slide on the 2 spacers.

You should now have this



Place the Phantom on its back. Lower the gimbal into place and line up the 2x M3 x 30mm

screws with the holes.

Tighten up the screws a bit, but not fully just yet.

Fit the 2x M3 x 6mm screws, here



and here.

When all 4 screws are in place, tighten them all up.

You can then attach the power connector to the gimbal board. Make sure you connect it the

right way round. Red is Positive (+) and Black is negative (-). Connecting the power the

wrong way round will blow a fuse on the board. It is possible to repair the board if you do

this, contact us for details if you have done this.



7) Powering up the Gimbal.

Note: Put your GoPro camera in the gimbal before you connect up the power. The gimbal is

tuned to include the mass of the camera and will not work correctly without the camera

installed.

With the gimbal now connected to the Phantom, it is powered directly from the flight

battery. When you connect the flight battery make sure that the gimbal is kept very still. If

the gimbal senses any movement when it powers up it may not initialise properly.



8) Connecting the Tilt Control Cable

You can connect the gimbal board to your Naza controller to allow control of the tilt(pitch)

of the camera gimbal.

To get at the Naza controller you need to open up the Phantom. Full details on how to do

this are available from the DJI website, we suggest you get them and read them before

proceeding.

The tasks required to do this are

1) Connect the gimbal board to the Naza. Supplied with the gimbal is a cable for doing

this. It basically connects pins A1 & GND on the gimbal board to the F2 port on the

Naza.

2) Use the Naza-M Assistant Software to configure the Naza flight controller. This is

available to download from DJI. You need to turn on gimbal control and set both the

gimbal tilt and roll gains to 0.

3) You will also need a tilt control lever for your transmitter. The Phantom transmitter

has a hidden 7th channel that is used to control the gimbal tilt. To operate this

channel you need a lever that you can fit to the rear of your transmitter. These are

not available from Aeroxcraft as yet, but are widely available elsewhere.

Note: We have found the tilt control works best if you move the tilt lever slowly.

The following pictures give you an idea of what you need to do.

Remove the propellers.



Disconnect the compass cable.

Remove the landing gear.



Remove the screws that hold the Phantom housing together.



Connect the tilt cable to the Naza F2 port

Thread the cable through to the underneath of the Phantom housing.



Reassemble the Phantom housing.

Reattach the landing gear.

Reconnect the compass module.

Connect the tilt cable to pins A1 (white) and GND(black) on the gimbal board.

Brushless GoPro Gimbal for DJI Phantom - BRADATECH · Brushless GoPro Gimbal (Phantom) Manual v1.0...

Documents

Transcript of Brushless GoPro Gimbal for DJI Phantom - BRADATECH · Brushless GoPro Gimbal (Phantom) Manual v1.0...

USER MANUAL 1 - GoPro · PDF fileUSER MANUAL. JOIN THE GOPRO MOVEMENT facebook.com/GoPro youtube.com/GoPro instagram.com/GoPro. Your HERO5 Black 6

Parts - 3DR Site Scan: The Complete Commercial Drone … · 1 Parts Tarot gimbal GoPro HERO3 stabilization system IRIS+ mounting screws (2) Configuration cable Gimbals arrive preconfigured

Gimbal Manual

2018 Tacoma eBrochure - Toyota Official Site ® mount on the windshield is to be used with GoPro HERO cameras. GoPro camera not included. GoPro, HERO, the GoPro logo, and the GoPro

3 Operation Instructions G4S 3-Axis Handheld Gimbal EN...2019/09/26 · G4S 3-Axis handheld gimbal has a mini to micro port, It can connect the GoPro with a micro usb cable. You can

VikingUAS Xtreme 2.0 Gen II Standard Data Specifications...Xtreme 2.0 Gen II FPV/Aerial Photography Quad Features Features: • Beholder Brushless Gimbal with built in landing gear

Gimbal modeling

ARRIS Zhao Yun Pro User Manual - Arrishobby.com - … · 1 ARRIS Zhao Yun Pro User Manual Thank you for buying ARRIS Zhao Yun Pro 3-Axis brushless Gimbal. Each gimbal has been adjusted

GoPro Slidecast

CG03 3-Axis Brushless 4K Camera/Gimbal - Horizon Hobby · ®CG03 3-Axis Brushless 4K Camera/Gimbal Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni

GB200 2-Axis Brushless Gimbal - Heli Blade - … · EN 4 A. GB200 2-Axis Camera Gimbal w/CGO1 compatible mounting plate B. Assembled isolation mount C. (4) Mounting Screws D. Knurled

GB200 2-Axis Brushless Gimbal - Horizon Hobby · 2020. 3. 27. · Brushless Gimbal. EN 2 WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product

GOPRO Rechargeable Battery (Hero7 Black) GOPRO Super Suit ... · GOPRO Shorty(Mini Extension Pole+Tripod) GOPRO The Handler for HERO 7 GOPRO 3-Way Arm Tripod for HERO 7 ... HAMA Elite

3-Axis Stabilized Handheld Gimbal - FeiyuTech Gimbal · 3-Axis Stabilized Handheld Gimbal ... Reset the tilting axis of the gimbal to initial ... Mini-USB charging port) and G5, the

Es a Wk220024 Brushless Gimbal g 2d

QP0203015306 - AGM Hobby · AGM 3.Axis Brushless Gimbal FOR GOPR03 & GOPR03+ ( ìffiËYGopr03&Gopr03+) v 1.0 The user manual www. agmhobby. com

Tarot 2-Axis T-2D Brushless Gimbal for GoPro Hero3 User Manual ...

INTEGRATION FULL GPS AUTO-LEVELING SIX AXIS2-axis gimbal 3-axis gimbal battery and ac charger included gps and return to home high output brushless motors brushless power system full

Z1-Proud 3-axis GoPro handheld Gimbal - CVC · The calibration is applicable to Z1-Pro(GY-3DH), Z1-Rider, Z1-Proud, Z1-Smooth. Before the first operation, please calibrate the gimbal.

MiNi 2D Gimbal Manual 2016.1.11 复制MiNi 2D 2-Axis Brushless Gimbal For Aircraft ... Can be easily mounted in fixed wing, multirotor, helicopter for aerial photography, and can work