ZXSDR BS8900A Quick Installation Guide_R1.0_CH_EN

8/14/2019 ZXSDR BS8900A Quick Installation Guide_R1.0_CH_EN

http://slidepdf.com/reader/full/zxsdr-bs8900a-quick-installation-guider10chen 1/49

ZXSDR BS8900A _R1.0_CH_EN

ZXSDR BS8900A

Quick Installation Guide _R1.0_CH_EN



Table of Contents

1. Overview ........................................................................................................... 3

1.1 Physical Specifications ..................................................................... 3

2. Installation Tools ..................................................................................... 4 3. Installation Flowchart ............................................................................. 5 4. Cabinet Installation and Overlaying ................................................ 6

4.1 Cabinet Installation Space Requirements .......................... 6

4.2 Cabinet Top Cover Installation .................................................. 8

4.3 Cabinet Base Fastening ............................................................. 9

4.4 Installing a Cabinet to Its Base ............................................ 10

4.5 Cabinet Overlapping ........................................................................ 12

5. Module Installation ................................................................................ 15

5.1 BC8910A Module Installation in BC8910A Cabinet .................. 15

5.2 RC8910A Module Installation in RC8910A Cabinet .................. 16

5.3 PC8910A Battery Installation in PC8910A Cabinet .................... 17

6. Cable Connections ................................................................................. 18

6.1 B121 Cable connection between BC8910A (B121 Power Supply) and PC8910A (Internal Cables) ........... 18

6.2 B121 Cable connection between BC8910A (B121 Power Supply) and RC8910A (Internal Cables) .......... 24

6.3 B121 BC8910A (B121 Power Supply) ExternalCable Connection ................................................................................................... 26 6.4 RC8910A External Cable Connection ................................. 28

6.5 B900 ConnectingInternal Cables between the BC8910A (B900) and the PC8910A ......................... 32

6.6 B900 ConnectingInternal Cables between the BC8910A (B900) and the RC8910A ......................... 35

6.7 B900 Connecting the BC8910A(B900) to External Cables ...................................................................................... 37

6.8 B201 Cable connection

between BC8910A (B201) and PC8910A (Internal Cables) .................................. 39 6.9 B201 Cable connection

between BC8910A B201 and RC8910A (Internal Cables) ............................. 42

6.10 B201 BC8910A (B201 Power Supply) ExternalCable Connection ................................................................................................... 44

6.11 Note ............................................................................................. 46

7. Installation Check ................................................................................... 47

7.1 Cabinet Installation Check....................................................... 47

7.2 Cable Connection Check ......................................................... 47

:R1.0

FDDLET20121108BS8900A

:2012-11-08

:CL

Version No.: R1.0

Document No.:

FDDLET20121108BS8900A

Release d ate: 2012-11-08

Produced by:

CL Product Support Dept



1 Overview

1.1 Physical Specifications

BC8910A + RC8910A + PC8910A Typical Configuration : Baseband Cabinet (BC8910A) + RFS Cabinet (RC8910A) + Battery Cabinet (PC8910A)

BC8910A BBU BC8910A Configuration: Power Supply, Heat Exchanger, BBU and other accessories

PC8910A 4 8 PC8910A Configuration: 4 or 8 battery packs

RC8910A RSU82

RC8910A Configuration: Fan Unit, Power Distribution Unit, and RSU82



2. Installation Tools

Electrical punch drill

Earth resistance tester

Vacuum cleaner

Multimeter

Coaxial cable stripper

Power Strip

Screwdriver

Hex key wrench

Hydraulic Crimper

Wrench

Cutter

Claw hammer

Pliers

Steel tape

Spirit Level

Crimper

Safety helmet

Slip-proof glove

Hacksaw

Ladder



3 Installation Flowchart



4. Cabinet Installation and Overlaying

4.1 Cabinet Installation Space Requirements

Space requirements for overlaying installation:



Space requirements for side-by-side installation:

100mm~500mm

100~500mm

When the cabinets are installed side by side, the space between the cabinets should be 100 - 500 mm.



4.2 Cabinet Top Cover Installation

It is required to install top covers for the cabinets in a non-overlaying installation or for the cabinet on top of anoverlaying installation.

1. 1. Place the top cover on top of the cabinet.

2 4 M122. Fasten the top cover with four M12 inner hexagon screws, which are provided with steel washers.



4.3 Cabinet Base Fastening

1. 4

1. Place the base to a proper position as per designrequirements, and then determine the hole drillingpositions for the 4 expansion bolts.

2. 16mm 80mm

2. Drill holes of 16 mm in diameter and 80 mm in

depth on the determined hole positions. Strike theexpansion bolts vertically into the holes, until theyare flush with the ground.

3. M12

3. Put the M12 screws through cabinet base,insulation washer, flat washer, spring washer andnuts in turn, and then fasten the base on theground.



4.4 Installing a Cabinet to Its Base1 2 +2 M12 RC8910A

Installation Method 1: Two dowel pins & two M12 inner hexagon screws (used to fasten the RC8910Acabinet to its base)

M8 Dowel pin: M8 inner hexagon screws are used tofasten it to the base.

M12 M12 screws, provided with rubber washers, are used tofasten the cabinet to its base.

1. M8

1. Use two M8 inner hexagon screws to fasten thedowel pin to the back of the base, on which holesare provided holding pin installation. Note that thedowel pins must be installed vertically to thebase; or else, it will be difficult to install thecabinet.

2. RC8910A

2 Place the RC8910A cabinet on the base, and push itbackwards steadily, until the dowel pins are insertedin the fixing holes completely, and the sides of cabinetshould align to those of the base. Be careful not to gethurt while pulling the cabinet because the cabinetmay slide out of the base.

3. 2 M12

3. Use two M12 inner hexagon screws, which areprovided with rubber washers, to fasten the

cabinet to the base.

4.

4. Use the door holderto get the cabinetdoor secured whileinstalling the cabinetand cables.



2 4 M12 BC8910A/PC8910A Installation Method 2: Four M12 inner hexagon screws (used to fasten the BC8910A/RC8910A cabinetto its base)

M12

In the four bottom corners of the BBU cabinet, use M12inner hexagon screws, which are provided with rubberwashers, to fasten the BBU cabinet to the base or theRFS cabinet.

1. M12

1. In the four bottom corners of the battery cabinet, useM12 inner hexagon screws, which are provided withrubber washers, to fasten the battery cabinet to thebase.

2. 2. Install the bottom plate of battery to its original

position after the battery cabinet is fastened to thebase.



4.5 Cabinet Overlapping

Before one cabinet is overlaid on another cabinet, remove the cable trough cover plates (on both sides) and thecable hole cover plates (in the middle) on top of the cabinet.

1

1. Remove the screwthat fastens the cabletrough cover plateand then remove thecover plate.

2. 2. Remove the four screws that fasten the cable hole

cover plate inside the cabinet and then remove thecover plate.

3. M12

3.Use four M12 inner hexagon screws, which areprovided with rubber washers, to fasten the upper

cabinet to the lower one, through the screw holeson the four bottom corners of the cabinet.

4 4. Remove the cable hole cover plates from the bottom of

the upper cabinet.



5. 5. Fasten the cable hole assemblies to the

positions, where cable hole cover plates areremoved.

6.

6. Secure the screws on the four corners of the cablehole assembly to fasten the cable hole assembly tothe lower side of the cable hole.

7.

7. Fasten the cable hole assemblies to the cableholes with the screws that previously fasten thecable hole cover plates.

The cable hole assembly must be installed securelyand tightly, or else, water may soak through thecabinet.

Cabinet overlaying is completed.

Note: You must install a top cover to the cabinet priorto the cabinet overlaying.

Fastening and overlaying of cabinets are completed.



NOTE:

1. BC8910A

4 M12 1. If there is a heater in the BC8910A,remove the screws which fasten theheater, then pull out the heater (Don’tremove the power cable of the heater),and finally fasten four M12 screws.

2. BC8910A2U

4 M12 2. If the BC8910A cabinet is fullyconfigured before ex-works, you needto remove the assemblies in the 2Uabove the heater, then install the fourM12 screws.



5. Module Installation

5.1 BC8910A Module Installation in BC8910A Cabinet

BC8910A

For the BC8910A cabinet, the power monitoringmodule (the right module in the red box) and therectifier module are required to be installed on site.

1

1. Insert the power monitoring module smoothly tothe far right slot, until the external side of themodule is flush with the shelf. Fasten the captive

screw on the lower part of the module to fastenthe module.

2

2. To insert the rectifier module, lift the handle on thelower part of the module, and then insert themodule to the corresponding slot smoothly, untilthe external side of the module is flush with theshelf, then release the handle.



5.2 RC8910A Module Installation in RC8910A Cabinet

RC8910A 6 RSU82 RSU82RSU82 RSU82 RSU82

The RC8910A cabinet can accommodate 6 RSU82modules. After the RSU82 modules are installed,connect the RSU82 power cables to the RSU82power ports. The RSU82 power cables are alreadyrouted to their respective slots.

RSU82 RSU82 RSU82 Align the protruding edges on the upper and lower sides to the guiding tracks of RSU82 slot and then push theRSU82 in to the slot smoothly.

1 RSU82 Figure 1. Protruding edge on upper/lower side of theRSU82

2 RSU82 Figure 2. RSU82 guiding track in the cabinet

1 RSU82

1. Push the RSU82along the track in tothe slot smoothly.

2 RSU82 3 M5X20 RSU82RSU82 RSU82

2. Fasten the RSU82 with 3 M5X20 screws respectively

on upper and lower sides. Note that the power port islocated at the lower side. Fasten the grounding platetogether with the middle screw on lower side of theRSU82.



5.3 PC8910A Battery Installation in PC8910A Cabinet

PC8910A4 8

4

Tidily place the battery packs in the PC8910Acabinet, with the electrodes facing outside. When 4battery packs are configured, place them at the lowershelf; and when 8 battery packs are configured, loadboth upper and lower shelves with 4 battery packsrespectively.

6.1.2

Note: The relevant cables must be well routed beforethe battery packs are loaded, or else, it is difficult toroute them. Refer to 6.1.2 for details.

4

If only 4 battery packs are installed, the insulatedlayer on the terminals of unused battery cables mustbe reserved.



6. Cable Connections

6.1 B121 Cable connectionbetween BC8910A (B121 Power Supply) and PC8910A (Internal Cables)6.1.1 Making Preparations

1. BC8910A 1. Remove the waterproof rubber plugs from both

sides of the BC8910A cabinet.

2. 2. Route all the cables through the cable holes and keepthem in place.

3. 3. Insert different cables through different holes ofwaterproof rubber plugs, depending on their diameters.

4. 4. Re-install the waterproof rubber plug.

5.

5. Use the ring spannerprovided in the RFScabinet to remove thescrew that fasten thecable trough cover plate,open the cable troughcover, install the requiredcables and then reinstallthe cover.

6.

6. There are two cable holes on the left and right sidesof the battery cabinet bottom. A waterproof plug iscovered on the top of the cable hole. Remove thewaterproof plugs before routing cables, and re-installthe waterproof plugs after cable routing is done.



6.1.2 Cable Connection in PC8910A



B121 Cable Connection between BC8910A (B121 Power Supply) and Battery Cabinet:

SN

Cable

Description

Quantity

Connector in B attery

Cabinet

B1 B1 Section of BC8910A

B2 B2 Section o f BC8910A

1 Fan powercable

1 Fan power port incabinet

B121_Load3 -48V B121_Load3 -48V RTN

2 Temperaturesensor cable

1 Battery surface

X1/X2

3 Access controlcable

1 Access control cableport in cabinet

TEC/DOOR DOOR DOOR connector of TEC/DOORport

4 Power supplycable

1 Power switch in batterycabinet

BATT 1 -48VBATT 2 -48V

BATT 1 -48V RTNBATT 2 -48V RTN

Precautions for Routing Cables A. 1/2/3 Cables 1, 2, and 3 are routed in the battery cabinet through the cable holes on the left side at the bottom of thebattery cabinet.

B. 4 Cable 4 goes into the battery cabinet through the cable hole on the right side of bottom of battery cabinet. Note thatthe plugs at both sides of cable hole should be kept in original positions after the cable is routed through. C. Protective tubes must be provided for the cables routed between cabinets. The length of protective tube shouldensure that no cable is exposed. The ends of protective tubes should be sealed with adhesive tapes D. 1/2/3/4 1/2/3 4

Cables 1, 2, 3, and 4 go through the external cable trough at the right side of RFS cabinet and then enter inside theBBU cabinet. The cables should be fastened via the cable fastening holes of the cable trough with the white cableties, with cables 1, 2, and 3 separating from cable No. 4. Note that the cables should be fastened flat on the cabletrough, or else, the cable trough cover plate can not be installed.

Cable Connections: 1. Connect the power cable of fan to the fan power port on the left wall of battery cabinet 2. Remove the protective paper on the probe of battery temperature transducer and stick the probe to the batterysurface. 3. Connect the access control cable to the access control cable port on the upper right of the battery cabinet. 4. Connect the battery power cable to the power switch on top of the battery cabinet.

Battery power cable connection:

V2.4 PC8910A Connecting the BAT cables of V2.4 PC8910A

V2.4 PC8910A BC8910A/

1. PC8910A BAT+ 2. PC8910A BAT-

There are one red cable and one black cable(BAT)between V2.4 PC8910A and BC8910A.1. Connect the red cable to the BAT+ of PC8910A.2. Connect the black cable to the BAT+ of PC8910A.



PC8910A 1. N 2. L

Power cables of the heater of PC8910A:1. Connect the blue cable to the N port (the fourth

terminal from top down).2. Connect the brown cable to the L port (the second

terminal from top down).

Fasten two screws of the panel.

V2.5 PC8910A Connecting the BAT cables of V2.5 PC8910A

V2.5 PC8910A BC8910A/

1. PC8910A BAT+ 2. PC8910A BAT-

There are two red cables and two blue cables(BAT)between V2.5 PC8910A and BC8910A1. Connect the two red cables to BAT+(1) and BAT+(2)

of PC8910A.2. Connect the two black cables to BAT-(1) and BAT-(1)

of PC8910A.

PC8910A 1. N 2. L

Power cables of the heater of PC8910A1. Connect the blue cable to the N port.2. Connect the brown cable to the L port.

Fasten two screws of the panel.



6.1.3 Cable Connection in BC8910A

1. “ B121_Load3_-48V” B121 LLVD2 Load3 “ B121_Load3_-48VRTN”

2. X1/X2 3. “ TEC/DOOR ” “ TEC ” “ DOOR ”

“ DOOR ”

4. “ BATT1/2 -48V ” “ BATT1/2 -48VRTN ” 5. B121 AC-OUT

1. Connect the “ B121_Load3_-48V” labeled terminal of fan power cable to the Load3 terminal of LLVD2 of B121power supply, and the “ B121_Load3_-48VRTN” labeled terminal to the power ground bar at the right side of BBUcabinet.

2. Connect the temperature sensor cable of the battery to the X1/X2 port. 3. The “TEC/DOOR” port of BBU cabinet provides a two-in-one cable, which has two connectors labeled as

“TEC” and “DOOR” respectively. Connect the access control cable to the “DOOR” connector. 4. Connect the black wire of battery power cable to the BATT1/2 -48V port, and the red wire to the BATT1/2

-48VRTN port. 5. Connect the battery cable to the AC-OUT port of B121.

After cable connections are done, the cables should be tidily and tightly fastened via cable fastening holes on the sidewall and bottom of cabinet.



6.2.2 Cable Connection

1. 1 A B 1. Connect end A of cable No.1 to the grounding bar on the left side of the BBU cabinet, and end B to the grounding connector ofthe RFS cabinet

2. 2 A B121 Load1 -48V B121 Load1 -48VRTN 2BRC8910A DCPD4X DC IN -48V -48VRTN 2. Connect A ends of cables No.2 to the cable connectors of B121 Load1. Connect the blue cable to the “-48V” port, connect the

black cable to the “-48VRTN” port. Connect B ends of cables No.2 to the DC IN port of DCPD4X of RC8910A. Connect the bluecable to the “-48V” port, connect the black cable to the “-48VRTN” port.

3. 3 A 0~5 BBU FS TX0RX0~TX5RX5 B RSU82 TX1RX1

3. Connect A ends of cables No.3 to the ports TX0RX0 ~

TX5RX5 of BBU FS boards as per the number sequencefrom 0 to 5. Connect B ends to the RSU82 TX1RX1 ports.



6.3 B121 BC8910A (B121 Power Supply) ExternalCable Connection6.3.1 Connection Preparation

External Cables

SN

Cable Description

Quantity

Connector in BC8910A

External Connector

1

Cabinet grounding bus

1

Grounding bar at the left side of thecabinet

Outdoor grounding bar

2GPS GPS feeder cable 1

GPS N N-type connector of GPS lightningarrester

GPS GPS antenna

3AC AC input powercable

2AC INPUT

AC INPUT port of power module

External power supply device

4 Ethernet cable

1 LPU ETH0 ETH0 port of LPU

External transmission device

5

Dry contact cable1 LPU MON_IN/OUT_G0

MON_IN/OUT_G0 port of LPU

External monitoring device

6

Others

It is dependent on the

contractualconfiguration.

- -

1. 1/2/3

2. 4/5/6

Routing Cables:1. Run cables 1, 2, and 3 from the left waterproof module at the bottom of the BC8910A to external devices along the left cable

trough of the RC8910A.2. Run cables 4, 5, and 6 from the right waterproof module at the bottom of the BC8910A to external devices along the right

cable trough of the RC8910A.




Cable Connections

1. 1. Connect the cabinet grounding bus to the grounding bar at the left side of the RFS cabinet, and then connect it to the nearestoutdoor grounding bar.2. GPS GPS N GPS 2. Connect the GPS feeder cable to the N-type connector of the GPS lightning arrester, and then connect it to the GPS antennaoutside.3. 3. There are three kinds of AC IN: single-phase, two-phase, and three-phase.

Single-Phase

Two-Phase

Three-Phase



4 Connecting Transmission Network Cable

LPU 1 BBU ETH0 2 In case no LPU is installed,1 Connect one end of the network cable to theETH0 port on the BBU.2 Connect the other end of the network cable to thecorresponding port on the transmission device.

10m LPU 1 1 BBU ETH0 2 1 LPU BBU_A0 3 2 LPU ETH_0 4 2 .When the network cable is longer than 10 m, youmust install the LPU.1) Connect one end of network cable 1 to the ETH0port on the BBU.2) Connect the other end of network cable 1 to theBBU_A0 port on the LPU.3) Connect one end of network cable 2 to theETH_0 port on the LPU.4) Connect the other end of network cable 2 to thecorresponding port on the transmission device.

6.4 RC8910A External Cable Connection

Cable Description

Quantity

Connector in BBU Cabinet

External Connector

RF jumper cable

RSU82 Determined by the quantity and model of RSU82

RSU82 RF port of RSU82

RF feeder cable

6.4.1 Connection Preparation

1 2 3 4

Structure: The waterproof module is made up of vertical slider(1), horizontal slider (2), cable-through plug (3) and plug (4).Principles:

1 The vertical slider exerts pressure downwards with the screwscrewed up.2

The horizontal sliders exert pressure to two sides with thedownward pressure from the vertical slider to press thecable-through plug, making it closely contact the cable in thecable-through hole, thus waterproof measure is achieved.



4.

4. Insert the vertical slider, and then fasten it tothe maximum extent with a hexagon spanner.

5. 3 1T2R RSU82

5. Install the three RF jumper cables of the1T2R RSU82 on the left in the same way.

6.

6. Note that the waterproof plugs should be tightly pressed. The cable holes that are not usedshould have their plugs in position.

7.

7. Use the internal adjusting screw to adjust the cable outlet plate at the cabinet base so that the opening size isminimized.

8. 8. After all cables are connected, reinstall the front plate of the

cabinet base.



NOTE:

PC8910A RC8910A

There is a dust network in the base of PC8910Aand RC8910A.

1. 1. Put the dust screen in the front of the base.

2. 6 2. Fasten the baffle with 6 screws.



6.5 B900 ConnectingInternal Cables between the BC8910A (B900) and the PC8910A6.5.1 Preparations

6.1.1 Refer to section 6.1.1 for details.

6.5.2 Connecting Internal Cables on the PC8910A 6.1.2 Refer to section 6.1.2 for details.

6.5.3 Connecting Internal Cables on the BC8910A (B900)



B900 Internal Cables Required for Connecting the BC8910A (B900) to the PC8910A

No.

Cable

Quantity

PC8910A Port

B1 BC8910A B1 Port

1 Fan cable

1 Fan port

TEC3

2 Temperature sensor cable

1 Battery surface

TEMP/OUTRLY

3 Access control cable

1 Access control port

TEC/DOOR DOOR TEC/DOOR port and DOOR

connector4

Power cable1

Power switchBATT Input (-48V)

5 Power cable of the heater inPC8910A

2Power port of heater inPC8910A

ADPD1 AC-OUT AC-OUT of ADPD1

Procedure for Connecting Internal Cables between the BC8910A (B900) and the PC8910A

1. Connect the fan cable.

a. B900

Unscrew and then de-attach the metal cover from the B900.

Note: The device names to be connected are screen-printedin this metal cover. Do not erase or remove any of them.

b.“ TEC ” TEC -48V

TEC -48VRTN According to the cable port layout that is screen-printed on themetal cover, connect the fan cable to the TEC connector.Connect the blue cable to the TEC -48V port.Connect the black cable to the TEC -48VRTN port.

2. TEMP/OUTRLY Connect the temperature sensor cable to the TEMP/OUTRLY port.3. BFAN FCE5 TEC/DOOR

“ DOOR ” A 2-in-1 cable is routed from the TEC/DOOR port of the FCE5 board in the BFAN assembly. Connect the access control cable

to the DOOR cable.



Connect the power cable.

a.

Run the power cable from the cable trough on the left side ofthe RC8910A to the BC8910A through the waterproofmodule on the lower left of the BC8910A.

b. B900 BATT input -48V“ +” 3

Connect the blue power cable to the BATT input (-48V) port.Connect the red power cable to the “+ 3” port.

Connect the power cable.

ADPD1 AC-OUT 1. AC-OUT N 2. AC-OUT L

Connect the power cable of the heater of PC8910A to theAC-OUT port of ADPD1:1. Connect the blue power cable to the N port of AC-OUT.2. Connect the brown power cable to the N port of

AC-OUT.



6.6.2 Procedure for Connecting Internal Cables between theBC8910A (B900) and the RC8910A

1. 1A B 2. 2 A RC0 -48V RC0 -48VRTN B 3. 3A 0~5 BBU FS TX0RX0~TX5RX5 B RSU82 TX1RX1

1. Connect the 1A end to the protection ground bar on the left side of the BC8910A.Connect the B end to the ground point onthe RC8910A2. Connect the blue power cable at the 2A end to the RC0 -48V port, and the black power cable to the RC0 -48VRTN port.

The B end is already connected.3. Insert cables 0 through 5 at the 3A end sequentially into TX0 RX0 to TX5 RX5, and the B end into RSU82 TX1 RX1After these cables are already connected, re-attach the metal cover. Tie-wrap the cables tightly at the bottom or on both sidesof the cabinets.



6.7 B900 Connecting theBC8910A (B900) to External Cables

6.7.1 PreparationsExternal Cables Required for Connecting the BC8910A

No.

Cable

Quantity

BC8910A Port

External Port

1 Cabinet ground bus

1 Ground bar

Outdoor ground bar

2 GPS GPS feeder cable

1 GPS N N-type port (GPS lightning arrester)

GPS GPS antenna

3 AC AC input cable

2 AC INPUT AC INPUT port (power distributionmodule)

External power supply

4 Ethernet cable



5 Dry contact cable

1 LPU MON-IN/OUT-GO MON-IN/OUT-GO port (LPU)


6 Other cable



1. 1/2/3 2. 4/5/6 Routing Cables:3. Run cables 1, 2, and 3 from the left waterproof module at the bottom of the BC8910A to external devices along the left

cable trough of the RC8910A.4. Run cables 4, 5, and 6 from the right waterproof module at the bottom of the BC8910A to external devices along the right

cable trough of the RC8910A.

6.7.2 Procedure for Connecting the BC8910A (B900) to ExternalCables



1. 2. GPS GPS N 3. AC “ AC-INPUT N ” “ AC-INPUT L1 ”

4. 6.3.2 5. LPU MON-IN/PUT-GO

1. Connect one end of the ground bus to the ground bar on the left side of the BC8910A, and the other end to the nearestoutdoor ground bar.

2. Connect the GPS feeder cable to the N-type port of the GPS lightning arrester tightly.3. Connect the blue wire of the AC input cable to the AC-INPUT N port, the brown wire to the AC-INPUT L1 port, and the

ground cable to the ground bar on the left side of the BC8910A.

4. Connect ethernet cable refer to section 6.3.2 for details.5. Connect the dry contact cable to the MON-IN/PUT-GO port of the LPU, and then tighten two screws on it.



6.8 B201 Cableconnection between BC8910A (B201) and PC8910A (Internal Cables)6.8.1 Connection Preparation


Cable Connection in Battery Cabinet



B201 Cable Connection between BC8910A (B201 Power Supply) and Battery Cabinet:

SN

Cable Descripti on

Quantity

Connector in Battery

Cabinet



1 Fan power cable

1 Fan power port in cabinet

B201_LLVD2_5 Power grounding bar on the rightside of cabinet

2 Temperature sensorcable

1 Battery surface

X4

3 Access control cable

1 Access control cable portin cabinet

TEC/DOOR DOOR DOOR connector of TEC/DOORport

4 Power supply cable

1 Power switch in batterycabinet

BATT Input 1BATT Input port 1 The power grounding bar on the

right side of cabinet

: 1. 1/2/3 2. 4 3. 4. 1/2/3/4 1/2/3 4

Precautions for Routing Cables:

1. Cables 1, 2, and 3 are routed in the battery cabinet through the cable holes on the left side of bottom ofbattery cabinet.

2. Cable 4 goes into the battery cabinet through the cable hole on the right side of bottom of battery cabinet.Note that the plugs at both sides of cable hole should be kept in original positions after the cable is routedthrough.

3. Protective tubes must be provided for the cables routed between cabinets. The length of protective tubeshould ensure that no cable is exposed. The ends of protective tubes should be sealed with adhesive tapes.

4. Cables 1, 2, 3, and 4 go through the external cable trough at the right side of RFS cabinet and enter insidethe BBU cabinet. The cables should be fastened via the cable fastening holes of the cable trough with thewhite cable ties, with cables 1, 2, and 3 separating from cable 4. Note that the cables should be fastened flaton the cable trough, or else, the cable trough cover plate can not be installed.

: 1. 2. 3. 4. Cable Connections: 1. Connect the power cable of fan to the fan power port on the left wall of battery cabinet.2. Remove the protective paper on the probe of battery temperature transducer and stick it to the battery

surface. 3. Connect the access control cable to the access control cable port on top right corner of battery cabinet. 4. Connect the battery power cable to the power switch on top of the battery cabinet.

Battery power cable connection:




6.8.3 Cable Connection in BBU Cabinet

1. “ BC8910A_B201_LLVD2_5” B201 LLVD2 5 “ BC8910A_-48VRTN”

2. X4 3. “ TEC/DOOR ” “ TEC ” “ DOOR ”

“ DOOR ” 4. “ BATT Input ” 1 5. A 6.

Cable Connections 1. Connect the “ BC8910A_B201_LLVD2_5 ” labeled terminal of fan power cable to the No. 5 terminal of LLVD2

of B201 power supply, and the “ BC8910A_-48VRTN ” labeled terminal to the power ground bar at the rightside of BBU cabinet.

2. Connect the temperature sensor cable of the battery to the X4 port. 3. The “TEC/DOOR” port of BBU cabinet provides a two-in-one cable, which has two connectors labeled as

“TEC” and “DOOR” respectively. Connect the access control cable to the “DOOR” connector. 4. Connect the black wire of battery power cable to the port of “BATT Input” switch No. 1, and the red wire to

the power grounding bar at the right side of BBU cabinet. 5. “A” is the power grounding bar. 6. After cable connections are done, the cables should be tidily and tightly fastened via cable fastening holes

on the side wall and bottom of cabinet.




1. 1 A B 1. Connect end A of cable No.1 to the grounding bar on left side of the BBU cabinet, and the end B to the grounding

connector of RFS cabinet

2. 2 A “ LLVD1-1 ”“ LLVD1-2 ”

“ -48VRTN ” “ -48VRTN ”B

2. Connect A ends of cables No.2 that are labeled as

“LLVD1-1” and “LLVD1-2” (they are power cables) tothe cable connectors of relevant switches. And connect

the cable labeled as “-48VRTN” to the “-48VRTN” power grounding bar. B ends of the cables are alreadyconnected to the power connectors of RFS cabinet.



3. 3 A 0~5 BBU FS TX0RX0~TX5RX5 B RSU82 TX1RX1

3. Connect A ends of cables No.3 to the ports TX0RX0 ~

TX5RX5 of BBU FS boards as per the number sequencefrom 0 to 5. Connect B ends to the RSU82 TX1RX1 ports.

There will be some cables connected to switches of BBU cabinet before ex-works. Make sure that these cables are notloosened during the installation on site.

After cable connections are done, the cables should be tidily and tightly fastened via cable fastening holes on the side wall and

bottom of cabinet.

6.10 B201 BC8910A (B201 Power Supply) ExternalCable Connection6.10.1 Connection Preparation

External Cables

SN

Cable Description

Quantity

Connector in BC8910A

External Connector

1 Cabinet grounding

bus

1 Grounding bar on the left side ofcabinet

Outdoor grounding bar

2 GPS GPS feeder cable

1 GPS N N-type connector of GPS lightningarrester

GPS GPS antenna

3 AC AC input powercable

2 AC INPUT AC INPUT port of power module

External power supply device

4 Ethernet cable



5 Dry contact cable

1 BBU DB25 DB25 connector of BBU data cable


6 Others



:1. 1/2/3 2. 4/5/6 Routing Cables:

1. Run cables 1, 2, and 3 from the left waterproof module at the bottom of the BC8910A to external devices along theleft cable trough of the RC8910A.

2. Run cables 4, 5, and 6 from the right waterproof module at the bottom of the BC8910A to external devices along the

right cable trough of the RC8910A.




Cable Connections 1. 1. Connect cabinet grounding bus to the grounding bar on the left side of RFS cabinet and then connect it to the nearestoutdoor grounding bar.2.GPS GPS N GPS

2. Connect the GPS feeder cable to the N-type connector of GPS lightning arrester, and then connect it to the GPS antennaoutside.3. AC INPUT 3. Connect the AC input power cable to the AC INPUT switch, and then connect it to external power supply device.

B201 4 N

L1 L2 L3 The B201 power supply input cable provides four

wires, in colors of blue, red, brown and black.Connect the blue wire to the N-type connector, andthe red, brown and black wires to the L1, L2 and L3connectors respectively.

4. 6.3.2 4. Connect ethernet cable refer to section 6.3.2 for details.5. BBU DB25 5. Connect the dry contact input cable to the DB25 connector of BBU data cable, and then connect it to an external monitoringdevice.



6. 6. For connection of other monitoring cables, refer to the connection instructions beside the monitoring cable input ports.

X4 Battery 1 Temperature( 1

X5 Battery 2 Temperature( 2

X12 Temperature Control X14 In-relay 1,2,3,41,2,3,4

X15 Out-relay 1,21,2 *



X21 RS485 CommunicationRS485

X22 RS232 CommunicationRS232

X23 Flooding Alarm X24 Smog Alarm X25 Ambient Temperature

X26 Entrance Control Alarm * Pin :NO(normal open)COM(common) NC(normal close

After cable connections are done, the cables should be tidily and tightly fastened via cable fastening holes on the side wall and

bottom of cabinet.

6.11 Note

1.2T4R RSU82ANT1/ANT3

1. For the 2T4R RSU82 used in aMulti-carrier One Sector application, itis required to connect the RF jumpercables to ANT1/ANT3 ports only.

2. RC8910A 3 RSU82

3 RSU82

2. If only three RSU82s are installedin PC8910A cabinet, the unused slotswill have dummy panels installed infactory. Install the three RSU82s tothe slots that are not covered on site.



8The cables or pigtails inside and outside the cabinet should not hang in the air.

9The bending radius of a cable should meet the requirement.

10DIN N

The connectors of all cables should be properly and firmly connected. No DIN or N-typeof connector is connected in a staggered way.

113-5 3 5mm) ( )

The black and white ties should not mix up: The white ties are used indoors, and itsend should be smoothly cut off; while the black ties are used outdoors and 3-5mm shouldbe reserved at the end.

12

,

The cable labels should face the same direction and be in correct format (or as requiredby the customer if relevant documents are provided).

ZXSDR BS8900A Quick Installation Guide_R1.0_CH_EN

Documents

Transcript of ZXSDR BS8900A Quick Installation Guide_R1.0_CH_EN