ZXSDR (V4.11.10.14P04) Engineering Commissioning Guide_R1.4_438022
ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
-
Upload
muhammad-ali -
Category
Documents
-
view
287 -
download
9
Transcript of ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
1/37
CDMA ZXSDR BS8900A(V8.30.01)
_R2.0_CH_EN
Outdoor Macro Base Station
Quick Installation Guide_R2.0_CH_EN
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
2/37
1. Overview.......................................................................................................... 3
2. Installation Tools ..................................................................................... 4
3. Installation Flow...................................................................................... 5
4. Cabinet Installation and Stack ......................................................... 6
4.1 Cabinet Installation Space Requirements .......................... 6
4.2 Cabinet Top Cover Installation .................................................. 8
4.3 Cabinet Base Fixation ................................................................ 9
4.4 Install Cabinet to Its Base .................................................... 10
4.5 Cabinet Stacking .............................................................................. 12
5.Module Installation................................................................................ 14
5.1 BC8910A Module Installation in BC8910A Cabinet .................. 14
5.2 RC8910A Module Installation in RC8910A Cabinet .................. 15
5.3 PC8910A Battery Installation in PC8910A Cabinet .................... 16
6. Cable Connections................................................................................. 17
6.1 Cable connection between BBUCabinet and Battery Cabinet (Internal Cables) ....................................................... 17
6.2 Cable connection betweenBC8910A and RC8910A (Internal Cables) ............................................................ 21
6.3 B201BC8910A (B201 Power Supply)External Cable Connection (External Cables) ........................................................ 23
6.4 RC8910A External Cable Connection (ExternalCables) .................................................................................................................... 25
6.5 B900 ConnectingInternal Cables between the BC8910A (B900)and the PC8910A .......................... 28
6.6 B900 ConnectingInternal Cables between the BC8910A (B900) and the RC8910A ......................... 30
6.7 B900 Connecting the BC8910A(B900) to External Cables ...................................................................................... 32
6.8 Note ............................................................................................... 34
7. Installation Check................................................................................... 35
7.1 Cabinet Installation Check....................................................... 35
7.2 Cable Connection Check ......................................................... 35
Table of Contents
Version No.
Document No.
CDMA20101229BS8900ARelease date:
Produced by:
CL Product Support
Department
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
3/37
1. OverviewBC8910AB201 Power Supply
PC891
0A
RC8910A
BC8910A+RC8910A +PC8910ATypical Configuration : BaseBand Cabinet (BC8910A)+RFS Cabinet (RC8910A)+Battery Cabinet (PC8910A).
B201 BBUBaseBand Cabinet Configuration: B201 Power Supply,Heat Exchanger, BBU and other accessories.
4 8
Battery Cabinet Configuration: 4 or 8 battery packs.
RSURF Cabinet Configuration: Fan Unit, Power Distribution Unit and RSU.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
4/37
2. Installation Tools
Electric Drill
Grounding ResistanceMeter
Vacuum Cleaner
Multimeter
Coaxial Cable Stripper
Power Strips
Screwdrivers
Hexagon Spanner
Hydraulic Pliers
Spanner
Paper Cutter
Nail Hammer
Pliers5m
5m Tape Measure
Spirit Level
Crimpers
Safety Helmet
Gloves
Steel Saw
Ladder
Star Tip Hexagon Spanner
10mm
Note: The 10mm hexagon spanner must be provided.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
5/37
3. Installation Flow
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
6/37
4. Cabinet Installation and Stack
4.1 Cabinet Installation Space Requirements Space requirements for overlapping installation:
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
7/37
Space requirements for side-by-side installation:
100~1000mm
When the cabinets are installed side by side, the space between cabinets should be 100~1000mm.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
8/37
4.2 Cabinet Top Cover Installation
It is required to install top covers for the cabinets in a non-overlapping installation or for the cabinet on top of
an overlapping installation.
1.
Place the top cover on top of the cabinet. NOTE that the side with no missing corner should face front.
2 4 M12
Fix the top cover with four (4) M12 inner hexagon bolts, which are provided with steel washers.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
9/37
4.3 Cabinet Base Fixation
1. 4
Place the base to a proper position as per designrequirements, and then determine the hole drilling
positions for the 4 expansion bolts.
2. 16mm 80mm
Drill holes of 16mm in diameter and 80mm in
depth on the determined hole positions. Strike theexpansion bolts vertically into the holes, until theyare flush with the ground.
3. M12
Put the M12 bolts through cabinet base, insulationwasher, flat washer, spring washer and nuts asper sequence, and then fix the base to ground.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
10/37
4.4 Install Cabinet to Its Base 12+2M12 RC8910AInstallation Method 1: Two Fixing Pins & two M12 inner hexagon bolts (used to fix RC8910Acabinet to Base)
M8
Fixing Pin: M8 inner hexagon screws are used to fix itto the Base.
M12
M12 bolts, provided with rubber washers, are used tofix cabinet to Base.
1. M8
Use two M8 inner hexagon screws to fix the FixingPin to the back of Base, on which holes are providedholding pin installation. Note that the fixing pins mustbe installed vertically to the Base; or else, it is difficultto install the cabinet.
2. RC8910A
Place the RC8910A cabinet on the Base, and push itbackwards steadily, until the fixing pins are in thefixing holes completely, then the sides of cabinetshould align to those of Base. Be careful not to gethurt while pulling the cabinet.
3. 2M12
Use two M12 inner hexagon bolts, which areprovided with rubber washers, to fix the cabinet to theBase.
4.
Use the door holder toget the cabinet doorsecured while installingcabinet and cables.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
11/37
24M12 BC8910A/PC8910AInstallation Method 2: Four M12 inner hexagon bolts (used to fix BC8910A/RC8910A cabinet toBase)
M12
In the four bottom corners of the BBU cabinet, use M12inner hexagon bolts, which are provided with rubberwashers, to fix the BBU cabinet to the Base or RFScabinet.
1. 6
Remove the 6 screws that fix the bottom plate of
battery cabinet, and then remove the bottom plate of
the battery cabinet.
2.M12
In the four bottom corners of the battery cabinet, useM12 inner hexagon bolts, which are provided withrubber washers, to fix the battery cabinet to the Base.
3
Install the bottom plate of battery to its originalposition after the battery cabinet is fixed to the base.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
12/37
4.5 Cabinet Stacking
Before another cabinet is stacked on, remove the cable trough cover plates and the cable hole cover plateson top of the cabinet.
1
Remove the screw thatfixes the cable troughcover plate and thenremove the cover plate.
2.
Remove the four screws that fix the cable hole coverplate from cabinet interior and then remove the cover
plate.
3. M12
Via the screw holes on the four bottom corners of thecabinet, use four M12 inner hexagon bolts, which are
provided with rubber washers, to fix the upper cabinetto the lower one.
4
Remove the cable hole cover plates on bottom of theupper cabinet.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
13/37
5.
Fix the cable hole assemblies to the positions wherecable hole cover plates are removed.
6.
Secure the screws on the four corners of the cablehole assembly, to fix the cable hole assembly to thelower side of the cable hole.
7.
Fix the cable hole assemblies to the cable holes withthe screws that previously fix the cable hole coverplates.
The cable hole assembly must be installed securely
and tightly, or else, water may soak inside thecabinet.
Cabinet stacking is completed.
Note: Install a top cover to the cabinet before cabinetstacking.
Fixation and stacking of cabinets are completed.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
14/37
5. Module Installation
5.1 BC8910AModule Installation in BC8910A Cabinet
BC8910A
For the BC8910A cabinet, the powermonitoring module (the right module inthe red box) and the rectifier module arerequired to be installed on site.
1
Insert the power monitoring modulesmoothly to the far right slot, until theexternal side of the module is flush withthe shelf. Fasten the captive screw onlower part of the module to fix themodule.
2
To insert the rectifier module, lift theholding handle on lower part of themodule and then insert the module tothe corresponding slot smoothly, untilthe external side of the module is flushwith the shelf, then release the handle.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
15/37
5.2 RC8910AModule Installation in RC8910A CabinetRC8910A 6 RSU
1T2R RSU 1/2/3 2T4R
RSU 4/5/6 RSU
RSU RSU
RSU
The RC8910A cabinet can
accommodate 6 RSU modules. Of
which, the 1T2R RSU modules are
installed to the left 1/2/3 slots and the
2T4R RSU modules are installed to the
right 4/5/6 slots. After the RSU modules
are installed, connect the RSU power
cables to the RSU power ports. TheRSU power cables are wired to relevant
slots.
RSU RSU RSU
Align the protruding edges on the upper and lower sides to the guiding tracks of RSU slot and then push theRSU in smoothly.
1RSU
Figure 1. The protruding edge on upper/lower side of
the RSU 2 RSU
Figure 2. The RSU guiding track in the cabinet
1RSU
Push the RSU along thetrack in smoothly.
2 RSU 3 M5X20 RSU
RSU RSU
Fix the RSU with 3 M5X20 screws respectively onupper and lower sides. Note that the power port islocated at the lower side. Fix the grounding platetogether with the middle screw on lower side of theRSU.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
16/37
5.3 PC8910A Battery Installation in PC8910A Cabinet
PC8910A
4 8
4
Tidily place the battery packs in the PC8910Acabinet, with the electrodes facing outside. When 4
battery packs are configured, place them at the lower
shelf; and when 8 battery packs are configured, load
both upper and lower shelves with 4 battery packs
respectively.
6.1.2
Note: The relevant cables must be well wired before
the battery packs are loaded, or else, it is difficult to
wire cables. Refer to 6.1.2for details.
4
If only 4 battery packs are installed, the terminals of
the battery cables that are not used must be
insulated.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
17/37
6. Cable Connections6.1 Cable connectionbetween BBU Cabinet and Battery Cabinet (Internal Cables)
6.1.1Connection Preparation
123
The waterproof module of BBU Cabinet consists of(1) fixing screw, (2) metal plate, and (3) waterproofrubber plug.
1.
To connect cables, remove the fixing screw first.
2.
Remove the metal plate and the waterproof rubberplug, and then wire all the cables through the cableholes and make them well arranged.
3.
Re-install the waterproof rubber plug to relevantcable holes according to the diameters of cables.Insert the metal plate and fix it with screw.
4.
6
Use the star tip hexagonspanner provided in RFSCabinet to remove the 6screws that fix the cabletrough cover plate, openthe cable trough cover,install the required cablesand then close it.
5.
There are two cable holes at left and right sides of thebattery cabinet bottom. Waterproof plugs areprovided in the cable holes. Remove the waterproofplugs before wiring cables, and re-install the plugsafter cable wiring is done.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
18/37
6.1.2 Cable Connection in Battery Cabinet
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
19/37
B201
Cable Connection between BC8910A (B201 Power Supply) and Battery Cabinet:
SN
Cable
Description
Quantity
Connector in Battery
Cabinet
B1 B1 Section of BC8910A
B2 B2 Section o f BC8910A
1
Fan powercable
1
Fan power port incabinet
B201_LLVD2_5
The power grounding bar atright side of cabinet
2
Temperaturetransducer
cable
1
Battery cell surface
X4
3
Access controlcable
1
Access control cableport in cabinet
TEC/DOOR DOOR
DOOR connector of TEC/DOORport
4
Power supplycable
1
Power switch in batterycabinet
BATT Input 1
BATT Input port 1
The power grounding bar atright side of cabinet
Precautions for Cabling
A. 1/2/3
The cables No.1/2/3 are wired in the battery cabinet through the cable holes at left side of bottom of batterycabinet.
B. 4 The cable No.4 goes into the battery cabinet through the cable hole at right side of bottom of battery cabinet.Note that the plugs at both sides of cable hole should be kept in original positions after the cable is wiredthrough.
C.
Protective tubes must be provided for the cables wired between cabinets. The length of protective tube shouldensure that no cable is exposed. The ends of protective tubes should be sealed with adhesive tapes D. 1/2/3/4 1/2/3 4
The cables No. 1/2/3/4 go through the external cable trough at the right side of RFS cabinet and enter inside theBBU cabinet. The cables should be fastened via the cable fastening holes of the cable trough with the whitecable ties, with cables No. 1/2/3 and cable No. 4 fastened separately. Note that the cables should be fastenedflat on the cable trough, or else, the cable trough cover plate can not be installed.
Cable Connections:
1.
Connect the power cable of fan to the fan power port on the left wall of battery cabinet2.
Remove the protective paper on the probe of battery temperature transducer and stick the probe to the batterysurface.
3.
Connect the access control cable to the access control cable port on top right corner of battery cabinet.4.
Connect the battery power cable to the power switch on top of the battery cabinet.
Battery power cable connection:
a.
Remove the cover of battery switch on top of battery
cabinet.
b.-48V (BAT-)
-48VRTN(BAT+)
Connect the black wire to the -48V (BAT-) terminal at
the right side of the switch, and the red wire to the-48VRTN (BAT+) terminal.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
20/37
6.1.3 Cable Connection in BBU Cabinet
Cable Connections
1. BC8910A_B201_LLVD2_5B201LLVD25BC8910A_-48VRTN
Connect the BC8910A_B201_LLVD2_5 labeled terminal of fan power cable to the No. 5 terminal of
LLVD2 of B201 power supply, and the BC8910A_-48VRTN labeled terminal to the power ground bar at
the right side of BBU cabinet.
2. X4
Connect the battery temperature transducer cable to the X4 port.
3. TEC/DOORTECDOOR
DOOR
The TEC/DOOR port of BBU cabinet provides a two-in-one cable, which has two connectors labeled as
TEC and DOOR respectively. Connect the access control cable to the DOOR connector.
4. BATT Input1
Connect the black wire of battery power cable to the port of BATT Input switch No. 1, and the red wire to
the power grounding bar at the right side of BBU cabinet.
A A shows the power grounding bar.
After cable connections are done, the cables should be tidily and tightly fastened via cable fasteningholes on the side wall and bottom of cabinet.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
21/37
6.2 Cable connectionbetween BC8910A and RC8910A (Internal Cables)
6.2.1 Connection Preparation
1. B201
Remove the screws on the four corners of B201power switch cover plate, and then remove the plate.Note that the plate has switch numbers printed.
2.
Fasten the cable hole assembly with screws in evenstrength.
B201
Cable Connection between BBU Cabinet (B201 Power Supply) and RFS Cabinet SN
Cable Description
Quantity
Connector in BBU Cabinet
Connector in RFS Cabinet
1
Cabinet grounding cable
1
BBU Cabinet grounding bar
RFS Cabinet grounding bar
2
RF Cabinet power cable
2 LLVD-1
LLD-1 port of power module
Power input port of RFS cabinet
3
High speed cable
RSU
The same as that ofRSU modules
BBU TX0 RX0~TX5 RX5
TX0 RX0 ~ TX5 RX5 ports of BBU
RSU TX1 RX1
TX1 RX1 ports of RSU
Cabling Route
1. 1/2
Cables No.1/2 enter the BBU cabinet through the cable hole at left side of the BBU cabinet. 2. 3
Cables No.3 enter the BBU cabinet in two bundles through the cable holes at left and right sides of the BBUcabinet.
High speed cable labeling and grouping
1. 0~5 BBU
TX0RX0~TX5RX5 0~2
3~5
Stick labels to both ends of the high speed cables,which indicate 0~5, corresponding to the portsTX0RX0~TX5RX5 of BBU. Cables 0~2 are in agroup, which enter BBU cabinet through the cableholes at right; and cables 3~5 are in a group, which
enter BBU cabinet through the cable holes at left.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
22/37
6.2.2 Cable Connection
1. 1 AB Connect end A of cable No.1 to the grounding bar on left side of the BBU cabinet, and the end B to the grounding connector of
RFS cabinet
2. 2 ALLVD1-1LLVD1-2
-48VRTN-48VRTN
B
Connect A ends of cables No.2 that are labeled as
LLVD1-1 and LLVD1-2 (they are power cables) to thecable connectors of relevant switches. And connect the cablelabeled as -48VRTN to the -48VRTN power grounding
bar. B ends of the cables are already connected to the powerconnectors of RFS cabinet.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
23/37
3. 3 A 0~5 BBU FS
TX0RX0~TX5RX5 B RSU TX1RX1
Connect A ends of cables No.3 to the ports TX0RX0 ~
TX5RX5 of BBU FS boards as per the number sequencefrom 0 to 5. Connect B ends to the RSU TX1RX1 ports.
There will be some cables connected to switches of BBU cabinet in factory. Make sure that these cables are not loosenedduring installation on field.
After cable connections are done, the cables should be tidily and tightly fastened via cable fastening holes on the side wall and
bottom of cabinet.
6.3 B201 BC8910A (B201 PowerSupply) External Cable Connection (External Cables)
6.3.1 Connection Preparation External Cables
SN
Cable Description
Quantity
Connector in BC8910A
External Connector1
Cabinet groundingbus
1 Grounding bar at left side of cabinet
Outdoor grounding bar
2 GPS GPS feeder cable
1 GPS N N type connector of GPS lightningarrester
GPS GPS Antenna
3 AC AC Input power
cable
2 AC INPUT AC INPUT port of power module
External power supply device
4 E1/T1
E1/T1 cable
1 BBU DB44
DB44 connector of BBU data cable
External transmission device
5
Relay monitoringcable
1 BBU DB25
DB25 connector of BBU data cable
External monitoring device
6 Others
Configured as per
agreement
Cabling Route
1. 1/2/3 Cables 1/2/3 go out from the waterproof module at left side of the bottom of BBU cabinet and out from the cable trough at left
side of RFS cabinet, and then they are connected to relevant external devices.
2. 4/5/6 Cables 4/5/6 go out from the waterproof module at right side of the bottom of BBU cabinet and out from the cable trough at
right side of RFS cabinet, and then they are connected to relevant external devices
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
24/37
6.3.2 Cable Connection
Cable Connections
1. Connect cabinet grounding bus to the grounding bar at left side of RFS cabinet and then connect it to the nearest outdoor
grounding bar.
2. GPS GPS N GPS
Connect the GPS feeder cable to the N type connector of GPS lightning arrester, and then connect it to the GPS antennaoutside.
3. AC INPUT Connect the AC input power cable to the AC INPUT switch, and then connect it to external power supply device.
B201 4
N L1L2L3 The B201 power supply input cable provides four wires, in colors of blue, red,brown and black. Connect the blue wire to the N connector, and the red,
brown and black wires to the L1, L2 and L3 connectors respectively.
4. E1/T1 BBU DB44 Connect the E1/T1 cable to the DB44 connector of BBU data cable, and then connect it to an external transmission device.
5. BBU DB25
Connect the relay input cable to the DB25 connector of BBU data cable, and then connect it to an external monitoring device.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
25/37
6. For connection of other monitoring cables, refer to the connection instructions beside the monitoring cable input ports.
X4 Battery 1 Temperature
( 1
X5 Battery 2 Temperature
( 2
X12 Temperature Control
X14 In-relay 1,2,3,4
1,2,3,4
X15 Out-relay 1,2
1,2*
X16 Out-relay 3,4
3,4*
X17 Out-relay 5,6
5,6*
X21 RS485 Communication
RS485
X22 RS232 Communication
RS232
X23 Flooding Alarm
X24 Smog Alarm
X25 Ambient Temperature
X26 Entrance Control Alarm
*Pin:NO(normal open)
COM(common)NC(normal close
After cable connections are done, the cables should be tidily and tightly fastened via cable fastening holes on the side wall andbottom of cabinet.
6.4 RC8910A External Cable Connection(External Cables)
Cable Description
Quantity
Connector in BBU Cabinet
External
Connector
RF jumper cable
RSU Determined by the quantity and model of RSU
RSU RF port of RSU
RF feeder cable
6.4.1 Connection Preparation
Principle and Operations on Waterproof Module
Structure and Principles of waterproof module.
123 4Structure: The waterproof module is made up of vertical slider (1), horizontal slider (2), cable-through plug (3) and plug (4).Principles:
1The vertical slider exerts pressure downwards with the screw is screwed up.
2
The horizontal sliders exert pressure to two sides with the downward pressure from the vertical slider to press the
cable-through plug, making it closely contact the cable in the cable-through hole, thus waterproof measure is achieved.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
26/37
Remove the waterproof module: Screw off the screw in the middle of the vertical slider to remove the waterproof module.
6.4.2 RF Jumper Cable Connection
3 2T4R RSU 3 1T2R
RSU
Three (3) RF jumper cables of 2T4R RSU go through thewaterproof module at right; and three (3) RF jumper cables of
1T2R RSU go through the waterproof module at left.
1. RSU
ANT1~4 2T4R RSU 1T2R
ANT1(TX1/RX1A)ANT2(RX1B)As per the sequence from right to left, connect the RF jumpercables to ports ANT 1~4 of RSU. If the 2T4R RSU uses 1T2Ronly, connect the jumper cables to the ANT1 (TX1/RX1A) portand ANT2 (RX1B) port.
2. 2 Install the corresponding waterproof plugs in position whenevery two RF jumper cables are connected.
3.
When the jumper cables that are required to go through this
waterproof module are connected and their waterproof plugs areinstalled in position, insert the horizontal sliders.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
27/37
4.
Insert the vertical slider, and then fix it to themaximum extent with a hexagon spanner
5. 3 1T2R RSU
Install the three (3) RF jumper cables of the 1T2RRSU at left in the same way.
6.
Note that the waterproof plugs should be tightly
pressed. The cable holes that are not used shouldhave their plugs in position.
7.
Use the internal adjusting screw to adjust the cable outlet
plate at the cabinet base so that the opening size isminimized.
8. After all cables are connected, install the front plate of the
cabinet base to its original position.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
28/37
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
29/37
B900 Internal Cables Required for Connecting the BC8910A (B900) to the PC8910A
No.
Cable
Quantity
PC8910A Port
B1 BC8910A B1 Port
1 Fan cable
1 Fan port
TEC3
2 Temperature
sensor cable
1 Battery surface
TEMP/OUTRLY
3
Access controlcable
1
Access control port
TEC/DOOR DOOR
TEC/DOOR port and DOORconnector
4 Power cable
1 Power switch
BATT Input (-48V)
Procedure for Connecting Internal Cables between the BC8910A (B900) and the PC8910A
1. Connect the fan cable.
a. B900
Unscrew and then de-attach the metal cover from the B900.
Note:The device names to be connected are screen-printed
in this metal cover. Do not erase or remove any of them.
b.
TEC TEC -48V
TEC -48VRTN According to the cable port layout that is screen-printed on
the metal cover, connect the fan cable to the TEC connector.
Connect the blue cable to the TEC -48V port.
Connect the black cable to the TEC -48VRTN port.2. TEMP/OUTRLY Connect the temperature sensor cable to the TEMP/OUTRLY port.
3. BFAN FCE5TEC/DOOR
DOORA 2-in-1 cable is routed from the TEC/DOOR port of the FCE5 board in the BFAN assembly. Connect the access controlcable to the DOOR cable.
Connect the power cable.
a.
Run the power cable from the cable trough on the left side of
the RC8910A to the BC8910A through the waterproofmodule on the lower left of the BC8910A.
b. B900 BATT input-48V
+3
Connect the blue power cable to the BATT input (-48V) port.Connect the red power cable to the + 3 port.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
30/37
6.6 B900ConnectingInternal Cables between the BC8910A (B900) and the RC8910A
6.6.1Preparations
1. B900
Unscrew and then de-attach the metal cover from the B900.
2.Ensure that the cable assembly is tightly and evenly screwed.
B900 Internal Cables Required for Connecting the BC8910A (B900) to the RC8910A
No.
Cable
Quantity
BC8910A Port
RC8910A Port
1 Ground cable
1 Ground bar
Ground point
2 Power cable
2 RC0 RC0 port
Power input port
3 High-speed cable
RSU It is identical to thequantity of RSUs.
BBU TX0 RX0~TX5 RX5 TX0 RX0 - TX5 RX5 port(BBU)
RSU TX1 RX1 TX1RX1 port (RSU)
Routing Internal Cables
3. 1/2 Run cables 1 and 2 from the left side of the cable route to the BC8910A.
4. 3 Run cable 3 in two groups from the left and right sides of the cable route to the BC8910A.
Labeling High-Speed Cables
1. 0~5 BBU
TX0RX0~TX5RX5 0~2
3~5 Stick two labels to both ends of a high-speed cable,respectively. Each label must be marked with a specificnumber ranging from 0 to 5 that matches TX0 RX0 to TX5
RX5. Run cables 0 through 2 from the right side of the cable
route to the BC8910A. Run cables 3 through 5 from the left
side of the cable route to the BC8910A.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
31/37
6.6.2 Procedure for Connecting Internal Cables between theBC8910A (B900) and the RC8910A
1. 1A B Connect the 1A end to the protection ground bar on the left side of the BC8910A.
Connect the B end to the ground point on the RC8910A.
2. 2 A RC0 -48V RC0 -48VRTN B Connect the blue power cable at the 2A end to the RC0 -48V port, and the black power cable to the RC0 -48VRTN port. The
B end is already connected.
3. 3A 0~5 BBU FS TX0RX0~TX5RX5 B RSU TX1RX1 Insert cables 0 through 5 at the 3A end sequentially into TX0 RX0 to TX5 RX5, and the B end into RSU TX1 RX1.
After these cables are already connected, re-attach the metal cover. Tie-wrap the cables tightly at the bottom or on both sidesof the cabinets.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
32/37
6.7 B900 Connecting theBC8910A (B900) to External Cables
6.7.1 PreparationsExternal Cables Required for Connecting the BC8910A
No.
Cable
Quantity
BC8910A Port
External Port
1
Main ground cable
1
Ground bar
Outdoor ground bar
2 GPS GPS feeder cable
1 GPS N N-shape port (GPS lightning arrester)
GPS GPS antenna
3 AC
AC input cable
2 AC INPUT
AC INPUT port (power distributionmodule)
External power supply
4 E1/T1 E1/T1 cable
1 LPU BSC-E1-GO BSC-E1-GO port (LPU)
External transmission device
5 Dry contact cable
1 LPU MON-IN/OUT-GO MON-IN/OUT-GO port (LPU)
External monitoring device
6 Other cable
It depends oncontractual
configuration.
- -
Routing External Cables
1. 1/2/3 Run cables 1, 2, and 3 from the waterproof module on the lower left side of the BC8910A to external devices along the left
cable trough of the RC8910A.
2. 4/5/6 Run cables 4, 5, and 6 from the waterproof module on the lower right side of the BC8910A to external devices along the rightcable trough of the RC8910A.
6.7.2 Procedure for Connecting the BC8910A (B900) to ExternalCables
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
33/37
1.
Connect one end of the main ground cable to the ground bar on the left side of the BC8910A, and the other end to the nearest
outdoor ground bar.
2. GPS GPS N
Connect the GPS feeder cable to the N-shape port of the GPS lightning arrester tightly.
3. AC AC-INPUT NAC-INPUT L1
Connect the blue wire of the AC input cable to the AC-INPUT N port, the brown wire to the AC-INPUT L1 port, and the
ground cable to the ground bar on the left side of the BC8910A.
4. E1/T1 LPU E1/T1-GO Connect the E1/T1 cable to the E1/T1-GO port of the LPU, and then tighten two screws on it.
5. LPU MON-IN/PUT-GO
Connect the dry contact cable to the MON-IN/PUT-GO port of the LPU, and then tighten two screws on it.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
34/37
6.8 Note
1.2T4R RSU
ANT1/ANT3 For the 2T4R RSU used in aMulti-carrier One Sector application, itis required to connect the RF jumpercables to ANT1/ANT3 ports only.
2 RC8910A 3
RSU
3
RSU
If only three (3) RSUs are installed inPC8910A cabinet, the unused slotswill have dummy panels installed infactory. Install the three (3) RSUs tothe slots that are not covered on field.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
35/37
7. Installation Check
7.1
Cabinet Installation Check
SN
Item
Check
1
The cabinet reliably fixed, with insulation washers, spring washers and flat washers correctlyinstalled.
2
The waterproof modules should be tightly installed and the unused cable holes should havetheir plugs in position.
3
The installation space satisfies requirements.
4
The front of the cabinet should have antistatic wrist straps provided.
5
The unused terminals inside the cabinet should be handled properly.
6
The screws on all modules should be fastened.
7.2 Cable Connection Check
SN
Item
Check
1The protection grounding wires of the equipment are properly installed to the nearest
copper grounding busbar.
2
Before connecting protection grounding wires, rust or dust should be removed from the
surface of the grounding terminal to ensure reliable connection.
3
The naked wires and the copper lugs of power cables or grounding wires should be covered
with a tube or wrapped with insulation tape. The copper lug should match the cable.
4
The power cables and grounding wires should be correctly and firmly connected in terms
of polarity. When the copper lug of a cable is connected to a terminal, flat washer andspring washer should be used and the spring washer should be pressed flat.
5
The extra part of the grounding wires or power cables should be smoothly cut off rather
than coiled. A whole cable segment with good insulation layer should be used. Do not
join two or more cables.
6
5cm
All cables (power cables, signal cables and pigtails) should be bound and laid by
classification, with a minimum parallel distance of 5cm.
7
300700mm
The cables should be evenly and firmly bound on the cable tray, with an interval ranging
from 300mm to 700mm.
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
36/37
8
The cables or pigtails inside and outside the cabinet should not hang in the air.
9
The bending radius of a cable should meet the requirement.
10
DINN
The connectors of all cables should be properly and firmly connected. No DIN or N type
of connector is connected in a staggered way.
11
3-535mm)()
The black and white ties should not mix up: The white ties are used indoors, and itsend should be smoothly cut off; while the black ties are used outdoors and 3-5mm should
be reserved at the end.
12
,
The cable labels should face the same direction and be in correct format (or as required
by the customer if relevant documents are provided).
-
8/13/2019 ZXSDR BS8900A Quick Installation Guide R2.0_CH_EN
37/37
CL
Planned by: CL Product Support Department
Edited by: Zhang Mao
English Text by: Chen Chunlin CL CDMA
Reviewed by: CL Product Support Department, CDMA Plan System Department,
Development & Pilot Department
* * * *
ZTE Corporation
Address: ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China
518057
Post Code: 518057
http://dms.zte.com.cn
Technical support website: http://tsm.zte.com.cn
075526770800 800-830-1118
Hotline: 86-755-26770800 or 800-830-1118
075526770801
Fax: 86-755-26770801