Scanner Setting - Aparatura Fiscala

Scanner Setting

Version 1.0 Copyright ©2009

2

1. Scanner setting Installation .........................................................................................4

2. How to start Scanner setting......................................................................................5

3. Scanner setting Menu Options...................................................................................6

3.1 File menu options .....................................................................................................6

3.2 Sync menu options...................................................................................................6

3.3 Communication menu options.................................................................................7

3.4 Help menu option .....................................................................................................7

3.5 Toolbar ......................................................................................................................7

3.6 Status Bar .................................................................................................................7

4. Scanner setting functions ...........................................................................................8

4.1 “IO \ System”.............................................................................................................8

4.2 “IO \ Keyboard” .........................................................................................................9

4.3 “IO\RS232”..............................................................................................................11

4.4 Out ..........................................................................................................................12

4.5 Barcode ...................................................................................................................15

4.5.1 UPC-A ..............................................................................................................15

4.5.2 UPC-E ..............................................................................................................16

4.5.3 EAN-13.............................................................................................................17

4.5.4 EAN-8...............................................................................................................18

4.5.5 Code-39 ...........................................................................................................19

4.5.6 Code-128 .........................................................................................................21

4.5.7 Codabar/NW7 ..................................................................................................23

4.5.8 Interleaved 2 of 5.............................................................................................25

4.5.9 Industrial 2 of 5 ................................................................................................27

4.5.10 Matrix 2 of 5 ...................................................................................................29

4.5.11 Code-93 .........................................................................................................31

4.5.12 Code-11 .........................................................................................................33

4.5.13 MSI/Plessey...................................................................................................35

4.5.14 UK/Plessey ....................................................................................................37

4.5.15 Telepen ..........................................................................................................39

4.5.16 RSS14 ............................................................................................................41

4.5.17 RSS Limited...................................................................................................42

4.5.18 RSS14 Stack .................................................................................................43

4.5.19 RSS Expansion .............................................................................................44

4.5.20 RSS Expansion Stack...................................................................................45

Appendix 1. Synchronization Troubleshooting ..............................................................46

3

Appendix 2. ASCII code command .................................................................................47

Appendix 3. How to Know COM port Selection ............................................................48

4

1. Scanner setting InstallationPlease follow the Installation procedure:Access to CD ROM, under the CD ROM directory: “Scanner SettingSoftware\Tools\Scanner setting”Copy the “Scanner setting” Folder to computer. For example: copy to desktop

5

2. How to start Scanner settingAccess to the folder where user had previously installed:1. Execute” Common.exe” in “Scanner setting” Folder.2. Please refer to the picture below:

Note: Before executing the software for scanner configuration, thescanner must scan the “Enter” and “ISP” barcodes to activate theconfiguration mode (please refer to Appendix 3). After scan thebarcodes, wait for few seconds for LED to change to flashing greencolor.

By this procedure, this means the scanner is in configuration mode, andthe user is able to configure the scanner by “Scanner setting” software.

6

3. Scanner setting Menu Options3.1 File menu options

New: Create a new file。Open: Open existing file。Save: Saving files. When saving files, the system will save the configuration

file with the extension of “.dat”.Save As: Save as another file.Recent file: record of recent opened file.Exit: Software termination.

3.2 Sync menu options

Properties: select this option will show the communication setting window asbelow.

Comport: Selection of COM port for file transmission.Baud rate: The file transmission speed rate setting.

Note: For “How to know COM port selection”, please refer to appendix 3

7

3.3 Communication menu options

Download Setting File: Download Setting File from PC to ScannerDownload kernel File:Download Kernel File from PC to SCANNERUpload Setting File: Upload Setting File from SCANNER to PC

Note: If connection failure. Please refer to Appendix 1 forsynchronization troubleshooting information.

3.4 Help menu option

About Software: Information of Scanner setting software version

3.5 Toolbar

New: Creates a new file.Open: Open existing file.Save: Saving the file.About: Information of Scanner setting software version.

3.6 Status BarStatus bar enables the user to notify the connection status.

When connection is not connected, the status is indicated as “UnLink”.

When connection is connected, the status is indicated as “Link”.

8

4. Scanner setting functions4.1 “IO \ System”

Power On Music: Enable this function will activate the music when the poweris on.

Power On Trigger: Enable this function will activate the LED light sourcewithout trigger.

Object Detect: This is auto sensor function. So even the LED is off, but when objector barcode under the scan range, it will be auto LED on and scanbarcode by set Enable.

Interface(Keyboard,RS232): Cable interface selection, Default: Keyboard

Object Detect Level: It is the function of auto detection. You can set up the level ofdetection sensitivity you want

Object Detect Time: It can adjust the Count for auto detection Count

Setup Timeout: this function enables to set the duration of the configurationtime. If the user does not perform any actions after entering thesetting mode, the setting mode will automatically exit.(Unit:1sec) (Range:0-255,Default:30).

9

4.2 “IO \ Keyboard”

Simulation: The PC usually checks the keyboard status during power on. It isrecommended to Enable this function if the user working withoutkeyboard installation. It simulates keyboard timing and passes thecurrent keyboard status to pc during power on.

Keypad: The settings of the numeric keypad, the keypad must be selected ifthe application program only accepts numeric keypad. (The righthand side of the numeric keys on the keyboard, and “NumLock”control key must be on.)

Caps Lock: The options of Caps lockAuto: This option enables the scanner to detect the current status of

keyboard Caps lock and display the barcode data.Alt + Keypad: If this option is selected, Caps Lock and output will be

independent. Please refer to the ASCII code table.Caps Lock Off: This option enables the barcode data in lowercase

when the keyboard is not installed in the PC/ Terminal.Caps Lock On: This option enables the barcode data in uppercase

when the keyboard is not attached with the PC/Terminal.

Example Barcode "ABCdef" Status Selection

Caps LockOn

Caps Lock Off

Auto ABCdef ABCdefAlt+Keypad ABCdef ABCdefCaps LockOff

abcDEF ABCdef

Caps LockOn

ABCdef abcDEF

10

Baud Rate(Low, Middle, High): Baud rate setting, Default: High.

Layout (US, UK, JP, FR, GR, IT, SP, Po): The options enable the user tospecify the language to match with computer keyboard layout.Default: US.

US: USAUK: UKJP: JapanFR: FranceGR: GermanyIT: ItalianSP: SpanishPo: Portuguese

Tx Gap: The delay time settings between each barcode data characterstransmission. If the transmission delay time setting is too high, theapplication program may not be able to receive all the barcode datacharacters. (Unit:1ms) (Range:0-255,Default:0)

Tx Delay: The delay time settings between the barcode data output, thisenables the user to set the output timing between each barcodedata scanned. (Unit:10ms) (Range:0-255,Default:0).

Timeout: the timeout setting for the handshaking acknowledgment from thehost PC. If scanner did not receive acknowledgement from the hostPC, the warning sound will be active. The function is particularuseful for some application which the host PC will take longerresponse time. (Unit:1sec) (Range:0-255,Default:3).

11

4.3 “IO\RS232”

USB MODE: If the scanner is in USB virtual COM interface, this option mustbe selected. (USB MODE enable), otherwise, the data will not be outputto the PC.

CTS Trigger: this option enables an external device to control scanning. TheCTS trigger is controlled by applying an external trigger signal to theCTS input,this option is only available when the trigger mode is set to“Mementary”.

Data Bits (7 Bits, 8 Bits): Default: 8 BitsStop Bits (1 Bit, 2 Bits): Default: 1BitBaud Rate: Default: 115200BpsProtocol (None, RTS/CTS, CTS/RTS, Scanner Ready, Data Ready,

XON/XOFF): Default: NoneParity (None, Odd, Even, Mark, Space): Default: NoneTx Gap: The delay time settings between each barcode data characters

transmission. If the transmission delay time setting is too high, theapplication program may not be able to receive all the barcode datacharacters. (Unit:1ms) (Range:0-255,Default:0)

Tx Delay: The delay timing settings between the barcode data output, thisenables the user to set the output timing between each barcodedata scanned. (Unit:10ms) (Range:0-255,Default:0)..

Timeout: the timeout setting for the handshaking acknowledgment from thehost PC. If scanner did not receive acknowledgement from the hostPC, the warning sound will be active. The function is particular usefulfor some application which the host PC will take longer response time.(Unit:1sec) (Range:0-255,Default:3).

Note: If “USB MODE“option is enable, it does not support Protocol setting.

12

4.4 Out

Good Read Beep: This option enables the Beep sound when the barcodedata is successfully read.

Good Read Vibrator: This option enables the vibration when the barcodedata is successfully read.

Reject Same: The option enables to reject the same barcode data scanned;this option is only available when the trigger mode is set to“Continue” and “Timeout off”.

Double Confirm: This option enables the scanner to double confirm thebarcode data, if this option is enabled, the scanner willrequire more times of successful decoding to confirm thebarcode data. This setting will refer to the double confirmcount , the more confirm counts will inhibit miss-readingbarcodes.

Tx Code Name: This option enables to show the barcode symbologies beforethe barcode data.

Tx Code Id: This option enables to show the barcode ID before or after thebarcode data.

Tx Control Code: This option enables to send out the control code whensome certain barcode has encoded control code within.

Tx length: This option enables to indicate the barcode length in front ofbarcode data.

Tx Preamble: This Option enables to append characters before the barcodedata.

Tx Postamble: This Option enables to append characters after the barcodedata.

Double Confirm Count: This enables the user to configure the doubleconfirm count, selecting higher value will affect the decodingspeed. (Range:1-10,Default:2)

13

Good read Time: This enables to set the scanning duration time for the samebarcode, this function only available when the trigger mode isset in “Continue”, “Momentary” and “Alternate” mode.(Unit:100ms) (Range:0-255,Default:5).

Standby Time: When the light source turns off, this function enables to setthe time to turn off the main power of the scanner. (Unit:1sec)(Range:0-255,Default:5).

Wait Addon Count: This setting is used for WPC add-on code, such asUPCA, UPCE, EAN13 and EAN8. The WPC code must bedecoded first, then Add-on code. Add-on code may not bedecoded with WPC at the same time. Therefore, you canset wait add-on count to force the add-on code must beoutput with WPC code together.If the Wait Add-on Count is set as “0”, the barcode data willonly be output with add-on code. (Range:0-99,Default:10)

Beep Volume: This enables to set the volume of the Beep sound(Range:1-10,Default:10)

Beep Time: This enables to set the duration of the beep sound. Deafult: 10ms. (Range:0-99,Default::10).

Beep Tone: This enables to set the frequency of beep sound, (Unit:100Hz)(Range:1-50,Default:27)..

Lamp Off Delay: This enables to set the duration time of laser beam poweron, the laser beam will automatically turn off if barcode label notscanned. This setting is only available when the trigger mode isset as” good read off” or “Timeout Off” (Unit:1sec) (Range:0-255,Default:5).

Led Off Delay: This enables to set the LED indicator flashing time, (Unit:10ms)(Range:0-255,Default:20).

Vibrator Off Delay: This enables to set the duration time of vibrator,(Unit:10ms) (Range:0-255,Default:10)

Global Min. Length: this function enables to set the minimum barcode length,if the barcode data is less than minimum length, thebarcode will not be decoded. (Range:0-64,Default:0)

Global Max. Length: This function enables to set the maximum barcodelength, if the barcode data is greater than maximumlength, the barcode will not be decoded. (Range:0-64,Default:0)

Note: the Global Min and Max length setting only applicable in fixedbarcode length type symbologies, for example, Code39, Code128, Code 93, Interleaved 2 of 5 and etc.

Preamble: This function enables to append the characters before the barcodedata transmitted.

Postamble: This function enables to append the characters after the barcodedata transmitted.

Prefix: Up to 10 characters can be programmed for prefix data. The prefixdata will be place after preamble data and before the barcode data.

Suffix: Up to 10 characters can be programmed for suffix data. The Suffixdata will be place before postamble data and after the barcode data.

14

Mode: This option enables to set the scanning trigger mode, default: “GoodRead Off”Test: This option enables the scanner to keep reading continuously,

and same barcode reading is allowed without double confirm. Thefeature can test the scanning performance and sensitivity.(Diagnostic mode)

Continue: This option enables the scanner to read the barcodecontinuously without triggering.

Good Read Off: Triggering to activate scanning, the light source ofscanner stops scanning when the barcode is successfullyread, or no barcode is read after the “Lamp Off Delay”duration time elapsed.

Timeout Off: Triggering to activate scanning, and scanner stopsscanning when no barcode is read after the “Lamp OffDelay” duration time elapsed.

Momentary: The trigger acts as a switch. Triggering to activatescanning and release to stop scanning.

Alternate: The trigger acts as a toggle switch, triggering to activate orstop scanning

Code ID Position: the option enables to set the position of Code ID. Default:“Before”.

Before: Barcode ID append before the barcode dataAfter: Barcode ID append after the barcode data.

Force Case: The option enables to set the case conversion Default: “None”None: No case conversionInverse: Inverse case (Uppercase converted to Lowercase and

Lowercase converted to Uppercase).Lowercase: Convert all characters to lowercase.Uppercase: Convert all characters to uppercase.

15

4.5 Barcode4.5.1 UPC-A

Read: The option enables to read the UPC-A barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of

barcode.TX Checksum: The option enables to display the check digits.Wait Addon: The option enables to display supplemental characters together

with the barcode.Truncate Lead: This enables to truncate the barcode data from the beginning

of the barcode. (Range:0-255)Truncate End: This enables to truncate the barcode data from the end of the

barcode. (Range:0-255)ID: ID data, Default value is A.Sub ID: Sub ID data, Default value is A.Insert0 Position: The position of the data insertion, if the insertion data

position is in the first position of the barcode data, specify as 0. If theinsertion data position is behind the barcode data, specify as 255.(Range:0-255)

Insert0 Data: User can specify the characters in the Insert0 Position.Insert1 Position: The position of the data insertion, if the insertion data

position is in the second position of the barcode data, specify as 1. If theinsertion data position is behind the barcode data, specify as 255.(Range:0-255)

Insert1 Data: User can specify the characters in the Insert1 Position.Addon Type: The options enable to read supplemental characters.

None : No Add-on code.Addon2 : 2 supplemental characters.Addon5 : 5 supplemental characters.Addon2+5 : 2+5 supplemental characters.

16

4.5.2 UPC-E

Read: The option enables to read the UPC-E barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of


with the barcode.Expansion: This option enables to extend the UPC-E barcode to UPC-A

barcode.Truncate Lead: This enables to truncate the barcode data from the beginning


barcode. (Range:0-255)ID data: ID data, Default value is E.Sub ID Data: Sub ID, Default value is E.Insert0 Position: The position of the data insertion, if the insertion data




Insert1 Data: User can specify the characters in the Insert1 Position.Addon type: The options enable to read supplemental characters.


17

4.5.3 EAN-13

Read: The option enables to read EAN-13 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of


with the barcode.ISBN/ISSN Conversion: This option enables to convert the EAN-13 barcodes

to ISBN/ISSN format barcode.Truncate Lead: This enables to truncate the barcode data from the beginning


barcode. (Range:0-255)ID: ID data, Default is F.Sub ID: Sub ID data, Default is F.Insert0 Position: The position of the data insertion, if the insertion data






18

4.5.4 EAN-8

Read: The option enables to read EAN-8 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of


with the barcode.Expansion: This option enables to extend the EAN-8 barcode to EAN-13



barcode. (Range:0-255)ID: ID data, Default is FF.Sub ID: Sub ID data, Default is FF.Insert0 Position: The position of the data insertion, if the insertion data






19

4.5.5 Code-39

Read: The option enables to read Code-39 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of

barcode.TX Checksum: The option enables to display the check digits.TX Start/End: The setting enables to display “*” in the beginning and the end

of the barcode.Truncate Lead: This enables to truncate the barcode data from the beginning


barcode. (Range:0-255)ID: ID data. Default is M.Sub ID: Sub ID data. Default is MInsert0 Position: The position of the data insertion, if the insertion data




Insert1 Data: User can specify the characters in the Insert1 Position.Min Length: If barcode data length is less then the Min length, it will not be

able to read this code. Default “0” represents no limits on barcode length.(Range:0-64)

Max Length: If barcode data length is more then the Max length, it will not beable to read this code. Default “0” represents no limits on barcode length.(Range:0-64)

20

Type: format options, default is Standard.Standard : Standard Code 39 code.Full ASCII : Full ASCII Code 39 code.

Format: This option enables to convert the barcode to Code-32.Disable: Disable code 32 conversion.Code-32 A: The converted barcode does not display character “A” in the

beginning of the barcode.Code-32 With ‘A’: The converted barcode displays character”A” in the

beginning of the barcode.Verify Checksum: The option enables to verify the check digits, if this option

is enable, any barcodes without check digits will not be able to scan.

Note: If Min length & Max length value are specified (not equals to 0) , when Minlength > Max length, The decoded barcode data will only display the valueof Min. Length and Max. Length.

21

4.5.6 Code-128

Read: The option enables to read Code-128 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of

barcode.TX Checksum: The option enables to display the check digits.Truncate Lead: This enables to truncate the barcode data from the beginning


barcode. (Range:0-255)ID: ID data, Default is K.Sub ID: Sub ID data. Default is K.Insert0 Position: The position of the data insertion, if the insertion data







22

Type: Data Type.Standard: Standard Code-128.UCC-128: This enables to convert to UCC-128 code.

Verify Checksum: The option enables to verify the check digits, if this optionis enable, any barcodes without check digits will not be able to scan.


23

4.5.7 Codabar/NW7

Read: The option enables to read Codabar/NW7 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of

barcode.TX Checksum: The option enables to display the check digits.Same Pair: User can specify if the starting and the ending of the barcode are

the same.TX Start/End: The setting enables to display the beginning and the end of the



barcode. (Range:0-255)ID: ID data, Default is N.Sub ID: ID data, Default is N.Insert0 Position: The position of the data insertion, if the insertion data







24

Type (ABCD/ABCD, abcd/abcd, ABCD/TN*E, abcd/tn*e): User can specifythe starting and the ending of the barcode. Default is ABCD/ABCD.



25

4.5.8 Interleaved 2 of 5

Read: The option enables to read Interleaved 2 of 5 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)ID: ID data, Default is I.Sub ID: Sub ID data Default is I,.Insert0 Position: The position of the data insertion, if the insertion data


Insert0 Data: User can specify the characters in the Insertion0 Position.Insert1 Position: The position of the data insertion, if the insertion data


Insert1 Data: User can specify the characters in the Insertion1 Position.Min Length: If barcode data length is less then the Min length, it will not be

able to read this code. Default “0” represents no limits on barcode length.(Range:0-64,Default:4)


26



27

4.5.9 Industrial 2 of 5

Read: The option enables to read Industrial 2 of 5 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)TX Checksum: The option enables to display the check digits.ID: ID data, Default is H.Sub ID: Sub ID data, Default is H.Insert0 Position: The position of the data insertion, if the insertion data







28



29

4.5.10 Matrix 2 of 5

Read: The option enables to read Matrix 2 of 5 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)ID: ID data, default value is G.Sub ID: Sub ID data, default value is G.Insert0 Position: The position of the data insertion, if the insertion data







30



31

4.5.11 Code-93

Read: The option enables to read the Code 93 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)ID: ID data, Default is L.Sub ID: Sub ID data, Default is L.Insert0 Position: The position of the data insertion, if the insertion data







32

Verify Checksum: Options of checksum, default is TwoDisable: No check digits checkOne : 1 digit checkTwo : 2 digits check


33

4.5.12 Code-11

Read: The option enables to read Code 11 barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)ID: ID data, Default is O.Sub ID: Sub ID data, Default is O.Insert0 Position: The position of the data insertion, if the insertion data







34

Verify Checksum: Checksum options, default is TwoDisable: No digit checkOne : 1 digit checkTwo : 2 digits check


35

4.5.13 MSI/Plessey

Read: The option enables to read the MSI/Plessey barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)ID: ID data, Default is P.Sub ID: Sub ID data, Default is P.Insert0 Position: The position of the data insertion, if the insertion data






Max Length: If barcode data length is more then the Max length, it will not beable to read this code. Default “0” represents no limits on barcodelength. (Range:0-64)

36

Verify Checksum (None, Mod 10, Mod 10/10, and Mod 11/10): ChecksumOptions. Default is “Mod 10”


37

4.5.14 UK/Plessey

Read: The option enables to read UK/Plessey barcodes.Truncate Zero: The setting enables to remove “0” digit in the beginning of



barcode. (Range:0-255)ID: ID data, Default is R.Sub ID: Sub ID data, Default is R.Insert0 Position: The position of the data insertion, if the insertion data







38



39

4.5.15 Telepen

Read: The option enables to read Telepen barcodesTruncate Zero: The setting enables to remove “0” digit at the beginning of

barcodeTx Checksum: The option enables to display the check digitsTruncate Lead: This enables to truncate the barcode data from the beginning


barcode. (Range:0-255)ID: ID data, Default setting is S.Sub ID: Sub ID data, Default setting is S.Insert0 Position: The position of the data insertion, if the insertion data







40

Type: Data type, Default :”Auto Switching”.Numeric: Numeric format.ASCII: ASCII format.Auto Switching: Numeric or ASCII format



41

4.5.16 RSS14

Read: The option enables to read RSS14 barcodesTruncate Zero: The setting enables to remove “0” digit at the beginning of

barcodeTx Checksum: The option enables to display the check digitsCode Mark: The option enables to insert “]e0” in front of the barcode.Application ID: The option enables to insert “01” in front of the barcode.Truncate Lead: This enables to truncate the barcode data from the beginning


barcode. (Range:0-255)ID: ID, Default setting is T.Sub ID: Sub ID, Default setting is T.Insert0 Position: The position of the data insertion, if the insertion data




Insert1 Data: User can specify the characters in the Insert1 Position.

42

4.5.17 RSS Limited

Read: The option enables to read RSS Limited barcodesTruncate Zero: The setting enables to remove “0” digit at the beginning of



barcode. (Range:0-255)ID: ID, Default setting is U.Sub ID: Sub ID, Default setting is U.Insert0 Position: The position of the data insertion, if the insertion data





43

4.5.18 RSS14 Stack

Read: The option enables to read RSS14 Stack barcodesTruncate Zero: The setting enables to remove “0” digit at the beginning of



barcode. (Range:0-255)ID: ID, Default setting is V.Sub ID: Sub ID, Default setting is V.Insert0 Position: The position of the data insertion, if the insertion data





44

4.5.19 RSS Expansion

Read: The option enables to read RSS Expansion barcodesTruncate Zero: The setting enables to remove “0” digit at the beginning of



barcode. (Range:0-255)ID: ID, Default setting is W.Sub ID: Sub ID, Default setting is W.Insert0 Position: The position of the data insertion, if the insertion data





45

4.5.20 RSS Expansion Stack

Read: The option enables to read RSS Expansion Stack barcodesTruncate Zero: The setting enables to remove “0” digit at the beginning of



barcode. (Range:0-255)ID: ID, Default setting is X.Sub ID: Sub ID, Default setting is X.Insert0 Position: The position of the data insertion, if the insertion data





46

Appendix 1. Synchronization Troubleshooting

If the connection failed to connect between Scanner and PC, errormessage will pop up as following.

Please refer to the following instruction to resolve the problem:

1. Please double check with COM port and Baud rate, if setting haschanged due to any reason, please correct settings.

2. If problem still existed, please contact your local dealer.

47

Appendix 2. ASCII code command

Some of the configuration column has no default value, the user is ableto enter the characters or command by referring to the ASCII code table.

The “$00” represents single data character, therefore,”$00$00” meanstwo data characters inserting to the setting column.

Referring to “00” from ASCII code table, it represents “NULL”, byinserting the commands by ASCII code, user must add extra “$” in frontof the ASCII code.

48

Appendix 3. How to Know COM port Selection

For how to know which COM port is connected between the scanner and thePC, please connect the scanner with the PC and scan the following barcode“Enter” and “ISP” to switch to Configuration mode.

Configuration Mode BarcodeEnter */$%ENT*ISP *ZISP*

After scan the “Enter” and “ISP” barcode, wait for few seconds for the LED tochange to flashing green color. And from the device manager, the user is ableto see the COM port connect to PC.

Please refer to the picture below.

Scanner Setting - Aparatura Fiscala

Documents

Transcript of Scanner Setting - Aparatura Fiscala