PROJECT: DATE: TO: RE: ATTN: JOB: WE ARE SENDING...
Transcript of PROJECT: DATE: TO: RE: ATTN: JOB: WE ARE SENDING...
15D5271-0002No.
Jeffrey Baker Architect10495 S Progess Way Ste #202 Parker CO 80134
TO:
10/07/2015DATE:
230000-HVACRE:
Jeffery BakerATTN:
Shop Drawings
Letter
Prints
Change Order
Plans
Samples
Specifications / Product Data
Other:
Approval
Your Use
As Requested
Review and Comment
Attached
Separate Cover Via:
Approved as Submitted
Approved as Noted
Returned After Loan
Resubmit
Submit
Returned
Returned for Corrections
Due Date: 10/14/2015
WE ARE SENDING: SUBMITTED FOR:
SENT VIA:
ACTION TAKEN:
TRANSMITTAL
David WallaceSigned:
PROJECT: Fit 36 Fitness-Fit 36
10/07/2015
Date
230000
Code
HVAC
Description
Architect Review
Status
JOB: 15D5271
CC:
Item
Submittal 230000
Package
1
Rev. Copies
Ph/Fax: 303-668-1474 303-223-9104
NOTES:
5995 Greenwood Plaza Blvd.Suite 100Greenwood Village, CO 80111-4710303-571-5377303-629-7467 (fax)
Air Purification Company
1861 West 64th Lane, Denver, Colorado 80221 Phone: 303.428.2800 • Fax: 303.428.2700
Project: Fit36 Location: Highlands Ranch, CO Engineer: kVA Contractor: Ducted Comfort Date: October 6, 2015 Submitted for Approval By:
Devon DuVal Devon DuVal [email protected]
Air Purification Company
1861 West 64th Lane, Denver, Colorado 80221 Phone: 303.428.2800 • Fax: 303.428.2700
Grilles, Registers, and Diffusers
Lay-In Stepdown Ceiling Diffusers – Titus TMS-3
05 – 12” x 12” / 06” Tag: CD
D-100 Radial Blade Damper
TRM Plaster Frame
Surface Mount Fixed Bar Louvered Return Grille – Titus 355RL-1
01 – Confirm Size Tag: RG
Surface Mount Double Deflection Supply Grilles – Titus 300RS-1
18 – 10” x 06” Tag: WR AG-15 Opposed Blade Damper
Surface Mount Fixed Bar Louvered Return Grilles – Titus 350RL-1 05 – Confirm Size Tag: ER
AG-15 Opposed Blade Damper
Surface Mount Linear Slot Diffusers – Titus ML-39
02 – 24” Long / 08” Inlet Tag: SD
(1) 1” Slot
Border Type 2A
End Borders XX
MPI-39 Insulated Plenum
*Contractor to confirm all sizes, quantities, throws, and finishes PRIOR to release
Exhaust Fans
Belt Drive Upblast Exhaust Fan – Twin City BCRU Series 01 – BCRU 110B Tag: EF-1
Gravity Backdraft Damper
NEMA 3R Disconnect, Loose
Bird Screen
12” Flat Canted Roof Curb
Submittal D-TMS 12-1-02
Square Ceiling DiffusersSteel • High PerformanceModel: TMS • Round Neck
Ceiling Module A minus 1/4"
B minus 1/8"
Nominal Round Duct Size B
Ceiling Module A
E
C
D
All dimensions are in inches. D-30.0-S
Ceiling Module A minus 1/4"
F
B minus 1/8"
Duct Size BNominal RoundCeiling Module A
C
E
D
Frame Type 3 (Lay-In) Full Face. For other border types, please see next page.
Frame Type 3 (Lay-In) Panel Mount. For other border types, please see next page.
* Adapter is provided for Sizes 4 and 5.
Ceiling ModuleA
Nominal RoundDuct Size B
Nominal Face Sizes F
C D E
24 x 24 4, 5* 12 X 12 2 3/4 5 1 1/8
24 x 24 6, 7 12 X 12 3/4 3 1 1/8
24 x 24 8 12 x 12 3/4 3 1 1/8
* Adapter is provided for Sizes 4 and 5.
Ceiling ModuleA
Nominal RoundDuct Size B
C D E
12 x 12 4, 5* 3 1/8 5 3/8 1 1/8
12 x 12 6, 7 1 1/8 3 3/8 1 1/8
12 x 12 8 1 1/4 3 1/2 1 1/8
24 x 24 6, 8 1 1/4 5 1 1/4
24 x 24 10, 12, 14, 15 1 3/8 5 1/8 1 1/4
(Please see reverse side).
Tag: CD
2
Ceiling Module A
Ceiling Module A
Ceiling Module A plus 1 1/4"
13/16"
minus 1"
1/8"
Ceiling Module A
3/8"
3/8"
HardwareMounting
by others
Adjusting Optional Damper • Removing Center Cone
Ceiling Module Face Size Nominal RoundDuct Sizes
12 x 12 12 x 12 4, 5, 6, 7, 8 1, 2, 3, 4
24 x 24 24 x 24 6, 8, 10, 12, 14, 15 1, 2, 3, 4
24 x 24 (Panel) 12 x 12 4, 5, 6, 7, 8 2, 3, 4
Frame Types
1. Remove center pin. 2. To adjust optional damper, insert screwdriver through hex hole.
3. To remove center cone, insert hex key (by others) and unscrew centerhub.
Frame Type 1 (Surface Mount)Full Face
Frame Type 2 (Snap-In)Full Face or Panel Mounted
Frame Type 4 (Spline)Full Face or Panel Mounted
Other Available Border Types
Duct by Others
1 1/2" D-75Mounts on NeckEG
A
Mounts above Neck
Duct by Others
1 1/2"AG-85
EG
1 5/8"
A
Model D-75 Opposed Blade DamperModel EG Equalizing Grid
Model D-75 damper is available induct sizes 6 thru 12 inches only.
3
Duct by Others
Mounts above Neck1 1/2"EG
B
AG-75
A
Duct by Others
Mounts above Neck
Air Flow
1 1/2"
A
AG-65
Model AG-75 Opposed Blade DamperModel EG Equalizing Grid
Model AG-65 Combination Damper andEqualizing Grid
Model AG-75 damper is available in 6, 7, 8,10, 12, 14, and 15 inch duct sizes only.
4
Size B6-12 1 1/2
14, 15 2 1/8
3
Accessories (Optional) Check if provided
Duct by Others
1 1/2"
Spring Clip
D-100Mounts on NeckEG
Model D-100 Radial Slide Blade DamperModel EG Equalizing Grid
Model D-100 damper is available in duct sizes 6, 8, 10,12 and 14 inch duct sizes only.
Duct by Others 1 3/4"
Mounts above Neck1 1/2"EG
AG-100
Model AG-100 Radial Sliding Blade DamperModel EG Equalizing Grid
Model AG-100 damper is available in duct sizes 6, 8, 10, 12and 14 inch duct sizes only.
Dimension “A” in Inches, for Dampers ShownNotes and :D-100 and AG-100 dampershave radial blades that slide ina horizontal plane. For thatreason, no opening clearance“A” is dimensioned.
Accessories Nominal Round Duct Sizes6 7 8 10 12 14 15
D-75 2 3/8 2 7/8 3 1/4 4 1/8 4 7/8 N/A N/A
AG-75 2 3/4 3 1/4 3 5/8 4 1/2 5 3/8 2 3/4 3
AG-85 2 1/2 3 3 1/2 4 1/2 5 1/2 6 1/2 7
AG-65 3 3/8 4 4 1/2 5 1/2 7 1/8 8 5/8 9
D-100 — — — — — — N/A
AG-100 — — — — — — N/A
21
2
5
3
6
4
1
Model AG-85 Butterfly DamperModel EG Equalizing Grid
5 6
5 6
(Please see reverse side.)
Submittal D-TMS
• Model TMS delivers supply air in a true 3600
pattern. Designed to protect ceiling fromstreaking and smudging.
• Excellent for variable volume systems. Theuniform, nearly horizontal jet from the outercone maintains effective room air distributioneven when air volume varies over a consider-able range.
• The TMS consists of 3 concentric cones in allsizes. This uniformity of design enhancesappearance in installations where more thanone size is involved.
• Screwdriver adjustment of the optionaldamper is achieved without removing the innercone. (See Note 2, Page 2).
• Quick removal of inner cone with a hex keyspeeds installation. (See Note 3, Page 2).
• All cones are die-stamped one piece con-struction with smooth, clean surfaces and nocorner joints.
• Material is heavy gauge steel.
• Optional molded insulation blanket (IB) withR-6 rating available for use with border styles1, 2, 3, and 4, 24x24 full face models.
Standard Finish: #26 White
General Description
TRM TITUS Rapid Mount Frame
For Surface Mounting Border Type 3
D-30.0-S
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawing on this submittal are not meant to detail everyaspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice.
Model SB Sectorizing BafflesOther Accessories (Optional) Check if provided
R-6 FIBERGLASS
TYPE 3 FRAME SHOWN
NECK SIZE
NECK SIZE + 2"IB Molded Insulation Blanket
Insulation is R-6 where blanket has the most depth. One inch clearance on each side of neck is left for insulated duct connection.24x24 Full face models only.
TYPE 1 FRAMETYPE 2 or TYPE 4 FRAMETYPE 3 FRAME
Grilles, Registers and Diffusers • AccessoriesAluminumModel: TRM • TITUS Rapid Mount Frame
TITUS® Submittal ABD-TRM 3-7-97
General Description• Model TRM TITUS Rapid Mount Frameallows T-bar, lay-in type diffusers (border Type3) to be installed in surface mounting applica-tions (border Type 1).
• TRM frame is installed in opening andsecured in place using security clips. Screwsare mounted flush in frame mounting holes.
• Rapid Mount Frame can be mounted inplaster or sheet rock ceiling.
• The TRM can be used to access ceilingplenum. Diffuser with flex connection can belifted out of frame to access ceiling space.
• Material is aluminum with steel fasteners.
Standard Finish: #26 White.
TITUS®990 Security Row • Richardson, Texas 75081 • 972-699-1030 • Fax 972-918-8880
ABD-23.0-S
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawings on this submittal are not meant to detail everyaspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice.
Clip is adjustable up and downto fit varying ceiling thicknesses.
CeilingModule
12 x 12 12 1/2 12 1/2
16 x 16 16 1/2 16 1/2
20 x 20 20 1/2 20 1/2
24 x 12 24 1/2 12 1/2
24 x 24 24 1/2 24 1/2
36 x 24 36 1/2 24 1/2
48 x 12 48 1/2 12 1/2
48 x 24 48 1/2 24 1/2
60 x 12 60 1/2 12 1/2
B C
*Recommended Ceiling Opening
(Check actual dimensions before installation.)
Frame Detail
Louvered Return Grilles and Registers • SteelModels: 355RL • 35° Deflection • Long Blades • 1/2” Blade Spacing
355RS • 35° Deflection • Short Blades • 1/2” Blade Spacing
D plus 1 3/4"
D minus 3/4"
9/16"
Opposed BladeOptional
Damper
For OptionalSlot OperatorScrewdriver
Damper
1 1/4"
D minus 1/2"
To Overall Depth.
When Damper IsFull Open, Add 3/8"
1 1/4"
35°
Note:
1/4"
2 1/2"
Nominal Duct Size D "
Submittal G-355R 1-1-01
(Please see reverse side for other border types..)
Border Type 1 • Surface Mount
Accessories (Optional) Check if provided
IS • Insect Screen (1/16” square mesh –galvanized steel)
DS • Debris Screen (1/4” square mesh –galvanized steel)
Other
Neck mounted opposed blade damper(galvanized steel)
Optional finish
Standard Finish: #26 White
Available Sizes (D” x D”)Border Type 1 is available in sizes 6” x 4” through 48” x 48” in 2” increments in one piece construction. Odd and fractional sizes are available atadditional cost. Sizes larger than 48” x 48” are shipped in multiple sections with joining strips for field assembly.
Note: Wall or duct opening should be duct size ± 1/8”. All dimensions are in inches.
Mounting Frames
5/16"
1 1/2"
1/4"
Duct plus 1/16"
1/4"
Duct plus 1 7/8"
1/4"
Duct plus 2 3/8"
1 1/2"
5/16"1/4"
Duct plus 2 3/8"
Duct plus 1 7/8"
Duct plus 1/16"
Duct Size Duct
Duct Size minus 3/4"
1/4"
1 1/4" x 3/4" Angle Clip
1 1/4" x 3/4" Angle Clip
(By Others)(By Others)
(By Titus)Attached To Grille
#8 Screw
Available with Border Type 1 only.
Type A • External Screw Type C • Concealed Screw PF • Steel Plaster Frame PFA • Aluminum Plaster Frame
Note: Wall opening should be listed duct size + 1/8” to listed duct size + 1/4”.
Fastenings
General Description• Available with louvers vertical or horizontal.
• #8 x 11/4” lg. Phillips flat head sheet metalscrews painted white.
• Optional opposed blade damper has screw-driver adjustment accessible through face ofregister.
• Material: Steel.
• All dimensions are ± 1/16”.
G-16.0-S
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawings on this submittal are not meant to detail everyaspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice.
EQT • Earthquake tabs
Surface Mounted Example Recessed Mounted Example
Tag: RG
Standard Finish: #26 White
Optional finish
Submittal G-355R 1-1-01
Border Type 2, 3, 4• Accessories & Options
Check if provided
IS • Insect Screen (1/16” square mesh –galvanized steel)
DS • Debris Screen (1/4” square mesh –galvanized steel)
EQT • Earthquake tabs
Other
AG-15 • Neck mounted opposed bladedamper (galvanized steel)
Border Type 7• Accessories & Options
Check if provided
EQT • Earthquake tabs
Other
G-16.0-S
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawings on this submittal are not meant to detail everyaspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice.
Standard Finish: #26 White
Optional finish
Ceiling Module Sizeminus 1/4"
Border Type 7 (Channel)
Ceiling Module Sizeminus 1/4"
plus 3/4"Ceiling Module Size
3/8"
3/8"
Ceiling Module Sizeminus 1/16"
13/16"
Optional Border Types AvailableBorder Type 2 (Snap-in)Panel Mounted
Border Type 4 (Spline)Panel Mounted
Border Type 3 (Lay-in)Panel Mounted
Available in 24” x 24” modules with neck sizes up to 20” x 20”.Available in all standard module sizes with neck sizes up to modulesize minus 2”.
Available in sizes up to 48” x 48”. Available in 24” x 24” modules with neck sizes up to 20” x 20”.
Splines on 2 opposite sides only
Louvered Supply Grilles and Registers • SteelModels: 300RL • Double Deflection • Long Front Blades • 3/4” Blade Spacing
300RS • Double Deflection • Short Front Blades • 3/4” Blade Spacing
Accessories (Optional) Check if provided
IS • Insect Screen (1/16” square mesh –galvanized steel)
DS • Debris Screen (1/4” square mesh –galvanized steel)
Other
Neck mounted opposed blade damper(galvanized steel)
D - 3/4"
Nominal Duct Size D "
D + 1 3/4"
Opposed Blade
9/16"
Damper
Optional
DamperFor OptionalSlot OperatorScrewdriver
1 1/4"
D - 1/2"
3/4"
To Overall Depth.
When Damper IsFull Open, Add 3/8"
1 3/4"
Note:
1/4"
3"
TITUS® Submittal G-300R 4-1-96
General Description• Available with front louvers vertical orhorizontal.• Optional opposed blade damper has screw-driver adjustment accessible through face ofregister.
• Front and rear louvers are individuallyadjustable.• Insect and debris screens are not availablewhen dampers are fitted.
• Material is steel.• #8 x 11/4” lg. Phillip’s flat head sheet metalscrews (painted).• All dimensions are ± 1/16”.
Optional finish
Standard Finish: #26 White
TITUS®990 Security Row • Richardson, Texas 75081 • 214-699-1030 • Fax 214-644-4953
G-6.0-S
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawing on this submittal are not meant to detail everyaspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice.
✓
Border Type 1 • Surface Mount
Available Sizes (D” x D”)Border Type 1 is available in sizes 6” x 4” through 48” x 48” in 2” increments in one piece construction. Odd and fractional sizes are available atadditional cost. Sizes larger than 48” x 48” are shipped in multiple sections with joining strips for field assembly.
Note: Wall or duct opening should be duct size ± 1/8”. All dimensions are in inches.
Mounting Frames
5/16
1 1/2
Duct + 2 3/8
Duct + 1 7/8
Duct + 1/16
1/41/4
Duct + 2 3/8
Duct + 1 7/8
1 1/2
5/161/4
Duct + 1/16
1/4
Duct Size
1 1/4
Duct Size - 3/4
Duct
1/4
Available with Border Type 1 only. Single deflection blades shown for clarity.For actual blade configuration see above. Type C fastening not available withdamper.
Type A • External Screw Type C • Concealed Screw PF • Steel Plaster Frame PFA • Aluminum Plaster Frame
Note: Wall opening should be listed duct size + 1/8” to listed duct size + 1/4”.Plaster frame may be surface mounted or recess mounted.
Fastenings
Surface Mounted Example Recessed Mounted Example
EQT • Earthquake tabs
Tag: WR
Louvered Return Grilles and Registers • SteelModels: 350RL • 35° Deflection • Long Blades • 3/4” Blade Spacing
350RS • 35° Deflection • Short Blades • 3/4” Blade Spacing
D plus 1 3/4"
Nominal Duct Size D "
9/16"
Model AG-15Opposed Blade
Damper
ScrewdriverSlot OperatorFor Optional
Damper
Optional
1 1/4"
D minus 1/4"
1 1/4"
Full Open, Add 3/8"When Damper Is
To Overall Depth.
035
Note:
1/4"
2 5/8"
Submittal G-350R 1-1-01
G-11.0-S
(Please see reverse side for other border types.)
Border Type 1 • Surface Mount
Accessories (Optional) Check if provided
IS • Insect Screen (1/16” square mesh –
galvanized steel)
DS • Debris Screen (1/4” square mesh –
galvanized steel)
Other
Neck mounted opposed blade damper
(galvanized steel)Optional finish
Standard Finish: #26 White
Available Sizes (D” x D”)Border Type 1 is available in sizes 6” x 4” through 48” x 48” in 2” increments in one piece construction. Odd and fractional sizes are available at
additional cost. Sizes larger than 48” x 48” are shipped in multiple sections with joining strips for field assembly.
Note: Wall or duct opening should be duct size ± 1/8”. All dimensions are in inches.
Mounting Frames
5/16"
1 1/2"
1/4"
Duct plus 1/16"
1/4"
Duct plus 1 7/8"
1/4"
Duct plus 2 3/8"
1 1/2"
5/16"1/4"
Duct plus 2 3/8"
Duct plus 1 7/8"
Duct plus 1/16"Duct Size
Duct
Duct Size minus 3/4"
1/4"
1 1/4" x 3/4" Angle Clip
1 1/4" x 3/4" Angle Clip
(By Others)(By Others)
(By Titus)Attached To Grille
#8 Screw
Available with Border Type 1 only. Type C fastening not available with
damper.
Type A • External Screw Type C • Concealed Screw PF • Steel Plaster Frame PFA • Aluminum Plaster Frame
Note: Wall opening should be listed duct size + 1/8” to listed duct size + 1/4”.
Fastenings
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawing on this submittal are not meant to detail every
aspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice.
General Description• Available with louvers vertical or horizontal.
• #8 x 11/4” lg. Phillip’s flat head sheet metalscrews painted white.
• Optional opposed blade damper has screw-driver adjustment accessible through face ofregister.
• Material: Steel.
• All dimensions are ± 1/16”.
EQT • Earthquake tabs
Surface Mounted Example Recessed Mounted Example
Tag: EG
Submittal G-350R 1-1-01
Optional finish
Standard Finish: #26 White
Optional finish
Standard Finish: #26 White
Border Type 2, 3, 4• Accessories & Options
Check if provided
IS • Insect Screen (1/16” square mesh –
galvanized steel)
DS • Debris Screen (1/4” square mesh –
galvanized steel)
EQT • Earthquake tabs
Other
AG-15 • Neck mounted opposed blade
damper (galvanized steel)
Border Type 7• Accessories & Options
Check if provided
EQT • Earthquake tabs
Other
Ceiling Module Sizeminus 1/4"
Border Type 7 (Channel)
Ceiling Module Sizeminus 1/4"
plus 3/4"Ceiling Module Size
3/8"
3/8"
Ceiling Module Sizeminus 1/16"
13/16"
Optional Border Types AvailableBorder Type 2 (Snap-in)Panel Mounted
Border Type 4 (Spline)Panel Mounted
Border Type 3 (Lay-in)Panel Mounted
Available in 24” x 24” modules with neck sizes up to 20” x 20”.
Available in all standard module sizes with neck sizes up to module
size minus 2”.
Available in sizes up to 48” x 48”.
Available in 24” x 24” modules with neck sizes up to 20” x 20”.
Splines on 2 opposite sides only
All rights reserved. No part of this work may be reproduced or transmitted in any form or any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
Note: This submittal is meant to demonstrate general dimensions of this product. The drawing on this submittal are not meant to detail every
aspect of the product with exactness. Drawings are not to scale. TITUS reserves the right to make changes without written notice. G-11.0-S
SS
SS
ML-37 • ½” Slot • Supply
ML-38 • ¾” Slot • Supply
ML-39 • 1" Slot • Supply
ML-40 • 1-½" Slot • Supply
Linear Slot Ceiling DiffusersAluminum • Modulinear
D-ML-1.0 6-23-10
Dimensions are in inches.
ML-37 S = ½”ML-38 S = ¾”ML-39 S = 1"ML-40 S= 1-½”
ModelSupply
MLR-37 S = ½”MLR-38 S = ¾”MLR-39 S = 1"MLR-40 S= 1-½”
ModelReturn
Border Type 1Awith • Flange Border• Screw Mounting
Border Type 1Bwith • Flange Border• Duct Mounting
Border Type 2ABorder Type 2Bboth with • Flanged Border• Concealed
Mounting
for #8 SMS (5/16" from Edge)
D'=Duct Size
O'= D' plus 7/8"
3/4"
1 1/8"
1/8"
1 3/4"
S
Countersunk Screw Holes
D'=Duct Size
1 1/8"S
3/4"
O'= D' plus 7/8"
1/8"
1 3/4"
1/8"
AS
1 3/4"
D'=Duct Size
3 5/16"
1/8" to 1/2"
3/4"
O'
Type A 0'
2A2B
1 1/87/8
D’ + ¾D’ + ¼
MLR-37 • ½” Slot • Return
MLR-38 • ¾” Slot • Return
MLR-39 • 1" Slot • Return
MLR-40 • 1-½" Slot • Return
Border Type 22with • Tape & Spackle
Border• H9 Hard Ceiling Clip
Note: ML/MLR-37 is not available for border 22
Tag: SD
Submittal ML-2.0 6-23-10
Frame & Border Types, Dimensions (cont’d) Check if provided.
Frame and Border Type 3with
• Flush Border• Concealed Mounting
Frame & Border Type 6with
• Plaster & Tile Mounting Frame• Flush Border• Concealed Mounting
Frame & Border Type 4with
• Flange Border• Concealed Mounting
Frame & Border Type 7AFrame & Border Type 7Bboth with
• Plaster & Tile Mounting Frame• Flange Border• Concealed Mounting
Border Type 12with
• Spline Border• Ceiling Hangers
Border Type 16with
• Curved Flange Border• Concealed Mounting• Equalizing Grid
Border Type 15with
• Flush Border• Ceiling Hangers
1 7/8"
S3/4"
O'=D'minus1/8"3/4"
D'=Duct Size
3 5/16"1 15/16"
S1 1/8"
3/4"
O'=D' plus 3/4"
1/8"
D'=Duct Size
3 5/16"
1/2"
S3/4"
O'=D' minus 1/8"3/4"
D' plus 1/2"D' plus 1 1/4"
D'=Duct Size
1 7/8"1"
3 5/16"
D'=Duct Size D' plus 1/2"
D' plus 1 1/4"
3/4"
O'
9/16"1 1/16"
AS 1/8"
3 5/16"
1 15/16"
Type A 0'
7A7B
1 1/87/8
D’ + ¾D’ + ¼
Border Type 9ABorder Type 9Bboth with
• Flange Border• Ceiling Hangers
Type A 0'
9A9B
¾1 1/8
D’ + 5/8D’ + 1 3/8
Border Type 11with
• Perimeter Plaster & Tile Mounting Frame
• Flush Border• Concealed Mounting
1/16"SA
O'
Hanger
1 3/4"
3 1/8"
D'=Duct Size
3/4"
D'=Duct Size
O'=D' minus 1/8"
S3/4"
3/4"
1 7/8"
1/2"1"
3/4"
3 5/16"
1 3/16"
7/16"
O'=D' minus 1/16"
Hanger
1 3/4"
7/16"
S3/4"
D' = Duct Size
3 1/8"
O'=D' minus 1/16"
1 1/16"
3/4"
7/16"S
3 1/8"
Hanger
1 3/4"
D'=Duct Size
Available in ML-38 only
1/2 X 1/2 X 1/2ALUMINUMEQUALIZING GRID
DUCT BY OTHERS
3/4
1 1/8
X X X Z YX ZY Y ZY Z
C O C O C O C O C O C O1A, 1B, 9B D -1 3/8 D +3/4 D -11/16 D +3/8 D -5/8 D +7/16 D D D +1/16 D +1/16 D +1/8 D +1/82A, 4, 7A, 16 D -1 3/8 D +3/4 D -11/16 D +3/8 D -5/8 D +7/16 D D D +1/16 D +1/16 D +1/8 D +1/83, 6, 11 D -1 3/8 D D -11/16 D D -5/8 D +1/16 D D D +1/16 D +1/16 D +1/8 D +1/82B, 7B D -1 3/8 D +1/4 D -11/16 D +1/8 D -5/8 D +3/16 D D D +1/16 D +1/16 D +1/8 D +1/89A D -1 3/8 D D -11/16 D D -5/8 D +1/16 D D D +1/16 D +1/16 D +1/8 D +1/812, 15 D -11/16 D D -5/16 D D -1/4 D +1/16 D D D +1/16 D +1/16 D +1/8 D +1/822 D -1 3/16 D +1 1/16 D -19/32 D +17/32 N/A N/A D D N/A N/A N/A N/A
Frame and/or Border Type
X-X X-Y X-Z Y-Y Y-Z Z-Z
Submittal ML-3.0 6-23-10
End FabricationX End Border Y Open End Z End Cap
C
D = Duct Size
O O
CD = Duct Size
O
D = Duct Size
C
Overall Length for Various End Fabrications
Duct Dimensions D’ (Width) for Various Frame & Border Types
ML/MLR37
ML/MLR38
ML/MLR39
ML/MLR40
ML/MLR37
ML/MLR38
ML/MLR39
ML/MLR40
S = 1/2 S = 3/4 S = 1 S = 1 1/2 S = 1/2 S = 3/4 S = 1 S = 1 1/21 1 7/8 2 1/8 2 3/8 2 7/8 2 2 1/4 2 1/2 32 3 1/8 3 5/8 4 1/8 5 1/8 3 1/4 3 3/4 4 1/4 5 1/43 4 3/8 5 1/8 5 7/8 7 3/8 4 1/2 5 1/4 6 7 1/24 5 5/8 6 5/8 7 5/8 9 5/8 5 3/4 6 3/4 7 3/4 9 3/45 6 7/8 8 1/8 9 3/8 N/A 7 8 1/4 9 1/2 N/A6 8 1/8 9 5/8 11 1/8 N/A 8 1/4 9 3/4 11 1/4 N/A7 9 3/8 11 1/8 12 7/8 N/A 9 1/2 11 1/4 13 N/A8 10 5/8 12 5/8 14 5/8 N/A 10 3/4 12 3/4 14 3/4 N/A
No. ofSlots
Types 1A, 1B Types 2A, 2B, 4, 7A, 7B, 16
ML/MLR37
ML/MLR38
ML/MLR39
ML/MLR40
ML/MLR37
ML/MLR38
ML/MLR39
ML/MLR40
S = 1/2 S = 3/4 S = 1 S = 1 1/2 S = 1/2 S = 3/4 S = 1 S = 1 1/21 2 1/8 2 3/8 2 5/8 3 1/8 1 3/8 1 5/8 1 7/8 2 3/82 3 3/8 3 7/8 4 3/8 5 3/8 2 5/8 3 1/8 3 5/8 4 5/83 4 5/8 5 3/8 6 1/8 7 5/8 3 7/8 4 5/8 5 3/8 6 7/84 5 7/8 6 7/8 7 7/8 9 7/8 5 1/8 6 1/8 7 1/8 9 1/85 7 1/8 8 3/8 9 5/8 N/A 6 3/8 7 5/8 8 7/8 N/A6 8 3/8 9 7/8 11 3/8 N/A 7 5/8 9 1/8 10 5/8 N/A7 9 5/8 11 3/8 13 1/8 N/A 8 7/8 10 5/8 12 3/8 N/A8 10 7/8 12 7/8 14 7/8 N/A 10 1/8 12 1/8 14 1/8 N/A
` = Not Available in Type 22
Types 9A, 9B, 12, 15, 22No. ofSlots
Types 3, 6, 11
X End Border (Type 22 Only)
Submittal ML-4.0 6-23-10
Accessories (optional) Check if provided.
This submittal is meant to demonstrate general dimensions of this product. The drawings are not meant to detail every aspect of the product. Drawings are not to scale. Titus reserves the right to make changes without written notice.
All rights reserved. No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
General Description• Standard lengths of diffuser sections
are 12”, 24”, 36”, 48”, 60” and 72”.
• Lengths greater than 72” are furnished in multiple sections, the number and size determined by the factory.
• Pattern controllers change direction and volume of air flow. Maximum length is 36”. Pattern controllers are furnished in multiple sections for diffuser longer than 36”.
Standard Finish: • #26 White border • Black pattern controllers.
• Mounting frames are cut to length and assembled in the field.
• Material is extruded aluminum with steel pattern controllers.
MLRF-37 • ½” Slot • ReturnMLRF-38 • ¾” Slot • ReturnMLRF-39 • 1” Slot • ReturnMLRF-40 • 1-½” Slot • Return
MLF-37 • ½” Slot • SupplyMLF-38 • ¾” Slot • SupplyMLF-39 • 1” Slot • SupplyMLF-40 • 1-½” Slot • Supply
Ideal when the exact length of an ML or MLR diffuser is not known until it is being installed.
Standard factory cut diffusers can be trimmed as much as 6 inches. If more than 6” is to be removed, use the optional field cut diffuser.
The field cut ML or MLR diffuser is 72” long, with the sides pre-punched to assure the proper alignment of field installed spacers.
These field installed spacers provide additional rigidity during and after cutting.Additional spacer kits available at extra cost.Cut Cut
90 Degree (minimum)Larger than 90 Degree. Specify_______________
MC-37 • ½” Slot • SupplyMC-38 • ¾” Slot • SupplyMC-39 • 1” Slot • SupplyMC-40 • 1-½” Slot • Supply
Optional Field Cut Diffuser (Unit includes one field spacer kit)
Optional Mitered Corner
O D O D O D O D O D O D O D O D1, 2 12 7/16 12 12 3/8 12 12 1/8 12 11 7/8 12 12 5/16 12 12 11/16 12 12 12 13 3/16 123-8 24 7/16 24 24 3/8 24 24 1/8 24 23 7/8 24 24 5/16 24 24 11/16 24 24 24 25 3/16 24
229A 9BNo. of Slots
12, 151A, 1B 2A, 4, 7A 2B, 7B 3, 6, 11Dimensions for 90 Degree Mitered Corners
All dimensions are in inches.
O
D =
Duc
t Siz
e
O
D = Duct Size
ANGLESPECIFY
MPI-37 • ½” Slot • InsulatedMPI-38 • ¾” Slot • InsulatedMPI-39 • 1” Slot • InsulatedMPI-40 • 1-½” Slot • InsulatedNote: endcaps are not insulated
MP-37 • ½” Slot • UninsulatedMP-38 • ¾” Slot • UninsulatedMP-39 • 1” Slot • UninsulatedMP-40 • 1-½” Slot • Uninsulated
Optional Plenum
Optional Blank-Offs
Note:• MP and MPI are available for all
frames and border types.
• Standard nominal lengths are 2, 3, 4 and 5 feet.
• Request Submittal D-MP for details.
• Option MP-SP available with maximum spread pattern.
MP-SP DesignOptional
BLKS - Cold Rolled Steel - Fits over Neck BLKV - Vinyl - Fits in Slot
MP-37 • ½” Slot Modulinear Plenum Adapters for ML Modulinear DiffusersMP-38 • ¾” Slot
MP-39 • 1" Slot
MP-40 • 1½" Slot
D-MP-1.0 6-25-10
Dimensions are in inches.
Slots MP-37 MP-38 MP-391 1 7/16 1 11/16 1 15/162 2 11/16 3 3/16 3 11/163 3 15/16 4 11/16 5 7/164 5 3/16 6 3/16 7 3/165 6 7/16 7 11/16 8 15/166 7 11/16 9 3/16 10 11/167 8 15/16 10 11/16 12 7/168 10 3/16 12 3/16 14 3/16
Width (W)
ML/MLREnd L
FabricationXX N-7/8XY N-7/8YY N-1/4ZZ N-1/4
A B6 Oval 6 1/4 5 1/48 Oval 9 3/8 5 1/410 Oval 12 1/2 5 1/412 Oval 14 1/8 7 7/8
DimensionsStandard Inlet Size
H
W 1 1/8"
1/2"
L
A
B
InternalOptional
Insulation(MPI Models)
Standard Inlets
2, 3 6, 8 6, 84, 5, 6 6, 8, 10 6, 8, 10, 12
Nominal Length (f t.)
Low Profile (LP) Units Oval (in.)
High Profile (HP) Units Oval (in.)
Note: End caps not insulated.
1A
1B
9A
9B
12
15
22
W
H
1 1/8"
1/2"
A
L
B(MPI Models)
InternalOptional
Insulation
ML/MLREnd L
FabricationXX N-7/8XY N-7/8YY N-1/4ZZ N-1/4
Standard Inlets
2, 3 6, 8 6, 84, 5, 6 6, 8, 10 6, 8, 10, 12
Nominal Length (ft.)Low Profile (LP) Units
Oval (in.)High Profile (HP) Units
Oval (in.)
A B6 Oval 6 1/4 5 1/48 Oval 9 3/8 5 1/410 Oval 12 1/2 5 1/412 Oval 14 1/8 7 7/8
DimensionsStandard Inlet Size
H LP HP(in.) 7 5/8 10 5/8
Note: End caps not insulated.
1 2 3 4 5 6 7 8MP-37 1 7/16 2 11/16 3 15/16 5 3/16 6 7/16 7 11/16 8 15/16 10 3/16MP-38 1 11/16 3 3/16 4 11/16 6 3/16 7 11/16 9 3/16 10 11/16 12 3/16MP-39 1 15/16 3 11/16 5 7/16 7 3/16 8 15/16 10 11/16 12 7/16 14 3/16MP-40 2 7/16 4 11/16 6 15/16 9 3/16 N/A N/A N/A N/A
ML/MLR
Type
WidthNumber of Slots
1 2 3 4 5 6 7 8MP-37 2 3/16 3 7/16 4 11/16 5 15/16 7 3/16 8 7/16 9 11/16 10 15/16MP-38 2 7/16 3 15/16 5 7/16 6 15/16 8 7/16 9 15/16 11 7/16 12 15/16MP-39 2 11/16 4 7/16 6 3/16 7 15/16 9 11/16 11 7/16 13 3/16 14 15/16MP-40 3 3/16 5 7/16 7 11/16 9 15/16 N/A N/A N/A N/A
ML/MLR Type
WidthNumber of Slots
Model MP Modulinear Plenum for ML/MLRBorder Type
Model MP Modulinear Plenum for ML/MLRBorder Type
H LP HP(in.) 8 11
2A
2B
Submittal MP-2.0 6-25-10
Accessories (optional)
This submittal is meant to demonstrate general dimensions of this product. The drawings are not meant to detail every aspect of the product. Drawings are not to scale. Titus reserves the right to make changes without written notice.
All rights reserved. No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc.
General Description• Model MP modulinear plenums are
tailored for field attachment to ML or MLR modulinear diffusers.
• Can be selected to integrate with all ML or MLR frame and border types.
• Standard lengths are 2’, 3’, 4’, 5’ and 6’.
• End caps can be turned up to allow installing the MP on continuous runs of ML diffuser.
• Available with optional internal insulation, Model MPI.
• Model MP can be used as supply or return.
• Available to fit ML or MLR 1-8 slot units.
• Material is steel.
Installation Details
Internal Insulation
L1 1/8W
Insulation(MPI Models)
H
1/2
A
B
OptionalInternal
Model MP Modulinear Plenum for ML/MLRBorder Type
3
4
6
7A
7B
11ML/MLR
End LFabrication
XX N-1/4XY N-1/4YY N-1/4ZZ N-1/4
Standard Inlets
2, 3 6, 8 6, 84, 5, 6 6, 8, 10 6, 8, 10, 12
Nominal Length (ft.)Low Profile (LP) Units
Oval (in.)High Profile (HP) Units
Oval (in.)
A B6 Oval 6 1/4 5 1/48 Oval 9 3/8 5 1/410 Oval 12 1/2 5 1/412 Oval 14 1/8 7 7/8
DimensionsStandard Inlet Size
H LP HP(in.) 7 5/8 10 5/8
Note: End caps not insulated.
Border Type 2A, 2B Frame & Border Types 3, 4, 6, 7A, 7B,11W=Duct Size
Concealed Mounting
1/8" to 1/2"
W=Duct Size
MPI-37 • For ML/MLR-37 • ½” Slot
MPI-38 • For ML/MLR-38 • ¾” Slot
MPI-39 • For ML/MLR-39 • 1” Slot
MPI-40 • For ML/MLR-40 • 1½” Slot
Model ID Inlet Damper
Note: Inlet damper is shipped loose.
4"
Border Type 1A, 1B, 9A, 9B, 12, 15, 22
1 2 3 4 5 6 7 8MP-37 2 3/16 3 7/16 4 11/16 5 15/16 7 3/16 8 7/16 9 11/16 10 15/16MP-38 2 7/16 3 15/16 5 7/16 6 15/16 8 7/16 9 15/16 11 7/16 12 15/16MP-39 2 11/16 4 7/16 6 3/16 7 15/16 9 11/16 11 7/16 13 3/16 14 15/16MP-40 3 3/16 5 7/16 7 11/16 9 15/16 N/A N/A N/A N/A
ML/MLR Type
WidthNumber of Slots
Submitted By:
Devon DuVal
Phone: 303-428-2800
X31
Fax: 303-428-2700
SUBMITTAL
1861 West 64th Lane
Denver, CO 80221-2347
Email:
Air Purification Co.
SUBMITTAL
Customer:
Job ID:
Ducted Comfort, LLC
Job Name: Fit36
5-3150
October 06, 2015Date:
Page 1 of 5Ver 10.0 October 2013 - Created 09-17-2015 Updated 10-06-2015 Owner Devon DuVal Air Purification Co.
SUBMITTAL
Customer:
Job ID:
Ducted Comfort, LLC
Job Name: Fit36
5-3150
October 06, 2015Date:
Tag: EF-1
Construction Features
Efficiency: Standard
Altitude: 5300 ftTemperature: 70 °F
Approximate weight each, includes fan, motor and accessories.
161N/A110BBCRU1
0.375 0.061,016525
ODP115V/1/601,7501/4
BCRU - Centrifugal Roof Exhauster, Upblast, Belt Driven
DescriptionQty Model Size Width
ConfigurationClass Rotation Arr Disch M. Pos
N/A N/A N/A UBD --
Motor Data
CFM RPMPerformance
HP RPM Volt/Ph/Hz Enclosure
Disch Dir
Vertical
Wt (lb.)
Oper. BHPSP (in WC)
• Spun aluminum construction
• Backwardly curved, non-overloading wheel.
• Wheel, motor, and drive assembly are isolated from the fan supports by rubberisolators.
• Top cap provides quick access to the wheel, motor, and drive assembly.
• Re-greaseable pillow block ball bearings provide an average life of 500,000 hours.
4.445594247525556575954Level at InletSound Data
Octave Bands 1 2 3 4
LwA: The overall (single value) fan sound power level in dB re.
dBA: Estimated sound pressure level (re:0.0002 microbar) based on a singleducted installation at 5 ft., using a directivity factor of 1.
5 6 7 8 LwA dBA Sones
10-12
Watts, ‘A’ weighted.
Accessories Included
Backdraft Damper, ALUM
Birdscreen (Zinc Plated Steel)
Disc Switch - Unfused (NEMA 3R), Mtd &Wired
Roof Curb, Canted, Alum. w/ Insulation12" H
Variable Speed Drive, 1.5 SF
Page 2 of 5Ver 10.0 October 2013 - Created 09-17-2015 Updated 10-06-2015 Owner Devon DuVal Air Purification Co.
SUBMITTAL
Customer:
Job ID:
Ducted Comfort, LLC
Job Name: Fit36
5-3150
October 06, 2015Date:
Tag: EF-1
Page 3 of 5Ver 10.0 October 2013 - Created 09-17-2015 Updated 10-06-2015 Owner Devon DuVal Air Purification Co.
SUBMITTAL
Customer:
Job ID:
Ducted Comfort, LLC
Job Name: Fit36
5-3150
October 06, 2015Date:
Tag: EF-1
Page 4 of 5Ver 10.0 October 2013 - Created 09-17-2015 Updated 10-06-2015 Owner Devon DuVal Air Purification Co.
SUBMITTAL
Customer:
Job ID:
Ducted Comfort, LLC
Job Name: Fit36
5-3150
October 06, 2015Date:
AMCA Statements
Tag: EF-1
No AMCA Statements
Page 5 of 5Ver 10.0 October 2013 - Created 09-17-2015 Updated 10-06-2015 Owner Devon DuVal Air Purification Co.