MARATHON GEARBOXES INLINE COAXIAL CATALOGUE
Transcript of MARATHON GEARBOXES INLINE COAXIAL CATALOGUE
2
See technical data table.
Page 9
Full stainless steel gearboxes with one stageof reduction.
See technical data table.
Page 8
See technical data table.
Full stainless steel Worm gearboxes.
IN THIS CATALOGUE
Full Stainless steel - One step gearboxes
Full Stainless steel - Worm gearboxes
3 Single Stage (One Step) GearboxesAluminium211A, 20 Nm 8
311A, 30 Nm 10
411A, 38 Nm 12
511A, 110 Nm 14
16 Inline Coaxial GearboxesAluminium202A, 70 Nm 22
302A, 120 Nm 24
402A, 160 Nm 26
403A, 160 Nm 28
452A, 300 Nm 30
502A, 350 Nm 32
503A, 350 Nm 34
602A, 520 Nm 36
603A, 520 Nm 38
41 Inline Coaxial GearboxesCast Iron - 1 Stage501C, 225 Nm 46
701C, 380 Nm 48
801C, 670 Nm 50
851C, 700 Nm 52
901C, 1175 Nm 54
56Cast Iron - 2 and 3 Stages502C, 320 Nm 56
503C, 320 Nm 58
702C, 675 Nm 60
703C, 675 Nm 62
802C, 900 Nm 64
803C, 900 Nm 66
852C, 1600 Nm 68
853C, 1600 Nm 70
902C, 2100 Nm 72
903C, 2100 Nm 74
76Cast Iron - 2 and 3 Stages1002, 2900 Nm 76
1003, 3000 Nm 78
1102, 4500 Nm 80
1103, 4600 Nm 82
84 Warnings & Warranty
84
See technical data table.
Page 9
Full stainless steel gearboxes with one stageof reduction.
See technical data table.
Page 8
See technical data table.
Full stainless steel Worm gearboxes.
IN THIS CATALOGUE
Full Stainless steel - One step gearboxes
Full Stainless steel - Worm gearboxes
3
FeetRemovable feet.
FlangeFully modular to IEC andcompact integratedmotor.NEMA C flange.
GearsHardened and ground gears.
Output shaftWith wellproportionedbearings.
Single piece aluminiumalloy housing
Combines light weight withhigh tensile strength.
Precision machined foralignment of bearings
and gearing.
Removableinspection coverAllows periodic inspectionof gearing during routinemaintenance.
Alloy housingIs vacuum impregnated (MIL-STD 276) forprotection and sealing. No secondaryfinish required but readily accepts paint.
A modular and compact product
Lubricated for life with
synthetic oil with operative rangefrom -15° to +130°C.
Ideal for use asfirst step withworm gearboxes.
Aluminium One Step Gearboxes
4
P -FAluminum one step gear
211A311A411A511A
311A
1
Special output shaft
BR
P
-F
H1-NMMounted feet
Only on request for quantity
Stage
Output flange mounted
With IEC motor
With male input shaft
With motor flange Without flange / feet
MountingSizeType
Modular base
On request we can deliver our products according to the ATEX.
HOW TO ORDER
511A
ø105IS ø14
2
Ratio Output Flange
S
D
A
-V=132(ø200)
-T=90(ø140)
-P=63(ø90)
-O=56(ø80)
-R=80(ø120)
-Q=71(ø105)
B-C
B
C
STANDARD
B32.84
Output Shaft
Specify only for vertical positions
B14
B5
-F=100÷112(ø250)
-E=90(ø200)
-B=63(ø140)
-A=56(ø120)
-D=80(ø200)
-C=71(ø160)
CEG
ø19ø24ø28
ø250
ø160ø200
ø14012345
-3 ø24(90B5)
511A
-0 ø11(63B5)
411A
-2 ø19(80B5)
STANDARD
511A
-2 ø19
411A
-1 ø14
211A311A
-3 ø24
ø14(71B5)
ø9(56B5)
ø28(100B5)
ø19(80B5)
ø24(90B5)
ø14(71B5)
-3
-1
-1
-Z
-4
-2-U=100÷112(ø160)
B6
B8
B7
V5
V6
øø
STANDARD
See technical data table
211A
511A
SCE
ø14ø19ø24
411A
SCE
ø14ø19ø24
311A
ø200
ø140ø160
ø1201234
311A
ø200
ø140ø160
ø1201234
411A
211A311A
ø120
-G=132(ø300)
Motor Size Terminal BoxPosition
MountingPosition
B3N Without flange
211A
Integrated flange
ø
øø
HOW TO ORDER
Flange
Type R
Without flange
5
511A
ø105IS ø14
2
Ratio Output Flange
S
D
A
-V=132(ø200)
-T=90(ø140)
-P=63(ø90)
-O=56(ø80)
-R=80(ø120)
-Q=71(ø105)
B-C
B
C
STANDARD
B32.84
Output Shaft
Specify only for vertical positions
B14
B5
-F=100÷112(ø250)
-E=90(ø200)
-B=63(ø140)
-A=56(ø120)
-D=80(ø200)
-C=71(ø160)
CEG
ø19ø24ø28
ø250
ø160ø200
ø14012345
-3 ø24(90B5)
511A
-0 ø11(63B5)
411A
-2 ø19(80B5)
STANDARD
511A
-2 ø19
411A
-1 ø14
211A311A
-3 ø24
ø14(71B5)
ø9(56B5)
ø28(100B5)
ø19(80B5)
ø24(90B5)
ø14(71B5)
-3
-1
-1
-Z
-4
-2-U=100÷112(ø160)
B6
B8
B7
V5
V6
øø
STANDARD
See technical data table
211A
511A
SCE
ø14ø19ø24
411A
SCE
ø14ø19ø24
311A
ø200
ø140ø160
ø1201234
311A
ø200
ø140ø160
ø1201234
411A
211A311A
ø120
-G=132(ø300)
Motor Size Terminal BoxPosition
MountingPosition
B3N Without flange
211A
Integrated flange
ø
øø
HOW TO ORDER
Flange
Type R
Without flange
6
9550P [KW] =M [Nm] n [rpm]
1000P [KW] =M [Kg] g [9.81] v [m / s]
1000P [KW] =F [N] v [m / s]
FR
M
d
FR
d [mm]fK
M [Nm] 2000FR [N] =
n [rpm]M [lb in] =63030 P[HP]
n [rpm]M [Nm] =9550 P[KW]
d [in]fK
M [lb in] 8.9FR [N] =
Rotation
Linear movement
Lifting
— If your application requires higher radial loads, contact our technical office. Higher load may be possible.
REQUIRED POWER
Factor
Output torque
Diameter of driving element
1.15 Gear wheels1.25 Chain sprockets1.75 Narrow v-belt pulley2.50 Flat-belt pulley
- Radial load generated by external transmissions keyed onto input and/or output shafts.
TORQUE
fK
USEFUL FORMULAS
RADIAL LOADS
Motor flange available
Mounting with reduction ring
Motor flangeholes position/terminal box position
Available without reduction bushes
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
Type of load and starts per hour Operating hours per day
3 h 10 h 24 h
≤ 10
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75 2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -O -P
63 71 56 63
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-Q
71
892493426362
1.572.843.293.87
0.370.370.370.37
3.33.33.22.9
CCCC
CCCC
Ratioscode
ø
Standardø14
2844195417561558
Output Shaft
01020304
3.97.08.19.6
Available B5Motor Flanges
Available B14Motor Flanges
QUICK SELECTION Input Speed (n1) = 1400 min-1
B
A
C
D
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
B)
C)
B)
P1R M2R
1.241.211.181.08
13232628
HOW TO SELECT A GEARBOX
30NmOne step311A Rating - Aluminium ONE STEP GEARBOXES
7
Motor flange available
Mounting with reduction ring
Motor flangeholes position/terminal box position
Available without reduction bushes
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
Type of load and starts per hour Operating hours per day
3 h 10 h 24 h
≤ 10
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75 2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -O -P
63 71 56 63
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-Q
71
892493426362
1.572.843.293.87
0.370.370.370.37
3.33.33.22.9
CCCC
CCCC
Ratioscode
ø
Standardø14
2844195417561558
Output Shaft
01020304
3.97.08.19.6
Available B5Motor Flanges
Available B14Motor Flanges
QUICK SELECTION Input Speed (n1) = 1400 min-1
B
A
C
D
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
B)
C)
B)
P1R M2R
1.241.211.181.08
13232628
HOW TO SELECT A GEARBOX
30NmOne step311A Rating - Aluminium ONE STEP GEARBOXES
8
20NmOne Step
The dynamic efficiency is 0.98 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -D -E -O -P -R
63 71 80 90 56 63
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-Q
80
682595500414298225169142
2.052.352.803.384.706.228.299.83
0.370.370.370.370.370.370.370.25
2.02.12.02.01.71.51.01.0
CCCCCCCC
Ratioscode
ø
Standardø14
19391740154213441047956758659
Output Shaft
0102030405060708
567812152016
Available B5Motor Flanges
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
71
FRFAn2
101600696756876960
504120138151175192
700600400300200140
LUBRICATION 211A Oil Quantity 0.05 Lt.
RADIAL AND AXIAL LOADSOutput Shaft
*Strong axial loads in the DX direction are not allowed.
Input Shaft
RADIAL AND AXIAL LOADS
FRFAn1
FA (N)
FR (N)
FR
tab. 2
192 960900
FA (N)
168 8401400
P1R M2R
CCCCCCCC
EN Unit 211A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
For all details on lubrication and plugs please consult with a Regalrepresentative or office
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
0.730.760.750.750.640.550.360.24
1012141720232016
211A Rating - Aluminium ONE STEP GEARBOXES 20 NmOne Step
1.40 kg
R211A-F... Basic Wormbox91
16
0
Detail Y
h1
n°8 - ø7
85
P211A-F... Basic Wormbox
5
16
ø14 h6
302.5
2.5 25
ø70
f 7
g6
81105
d1 52.4
M5x13ø14 h6
24
Kit CodeB14 MotorFlanges A g656 B1463 B1471 B14
9799.597
90105
80 KC404049K0504047K0504045
Kit CodeB5 MotorFlanges A g663 B571 B5
99.597 160
138 K0504041K0504042
M5x13
*Available output shaft
ø 14x30Standard
Shaft - d1 p15 M5x13
h116
x
2520
A
30
GearboxWeight
211A
9
20 NmOne Step
1.40 kg
R211A-F... Basic Wormbox91
16
0
Detail Y
h1
n°8 - ø7
85
P211A-F... Basic Wormbox
5
16
ø14 h6
302.5
2.5 25
ø70
f 7
g6
81105
d1 52.4
M5x13ø14 h6
24
Kit CodeB14 MotorFlanges A g656 B1463 B1471 B14
9799.597
90105
80 KC404049K0504047K0504045
Kit CodeB5 MotorFlanges A g663 B571 B5
99.597 160
138 K0504041K0504042
M5x13
*Available output shaft
ø 14x30Standard
Shaft - d1 p15 M5x13
h116
x
2520
A
30
GearboxWeight
211A
10
30NmOne Step
FR (N)
The dynamic efficiency is 0.98 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -O -P
63 71 56 63
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-Q
71
891493425362303222170129
1.572.843.293.874.626.308.2210.86
0.370.370.370.370.370.370.370.37
3.33.33.22.92.62.21.91.0
CCCCCCCC
CCCCCCCC
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
640FRFA
120700700140600
800160400880175300
10202002001120225140
Feq = FR . 38.5X+18.5
FRFAn2 FRFAn2
Ratioscode
ø
Standardø14
On requestø19ø24
284419541756155813601063974776
Output Shaft
0102030405060708
4781011162027
= =
Available B5Motor Flanges
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
8601801400980200900
FRFAn1
LUBRICATION 311A Oil Quantity 0.10 Lt.
n2
FA (N)
P1R M2R
For all details on lubrication and plugs please consult with a Regalrepresentative or office
tab. 1AGIP Telium VSF 320
EN Unit 311A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
SHELL Omala S4 WE 320
1.21.21.21.10.970.830.690.39
1323262830353828
311A Rating - Aluminium ONE STEP GEARBOXES
11
30NmOne Step
ø14 h6
ø75
P311-H1... With Feet
Kit Code
R311-N... Input Shaft
B14 MotorFlanges A g6 k1
P311-N... Basic Gearbox
56 B1463 B1471 B14
103105.5103
90105
80 106.5109
106.5
KC404049K0504047K0504045
Kit CodeB5 MotorFlanges A g6 k163 B571 B5
105.5103 160
138 109106.5
K0504041K0504042
38
g6
A
87
3039.5
25ø14 h6
ø60
h8
N. 4 - M8x14
35
N. 4 - M8x15 32 26
5
16
*See the table of output shaft for the complete list of diameters
M5x13
standard
M5x1325
97
5
16
132110
75
Kit CodeK4119024LM
113
13911018
ø9
35
2.50 kg
e1
s1
k1
b1 f 7
c1f1
a1
26.5
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130
140160200
100115130165
33
3.53.5
9*9911
KC309010KC309011KC309012KC309013
d1
3.5
Detail Y
h1
g6
30
*Holes position
Detail Y
x
p1
M5x13
ø14 h6
*Available output shaft
On requestø 14x30Standard
Shaft - d1 p15 M5x13
ø 24x40 8 M6x16
h116
27
x
P311-F... Output Flange
11.511.511.511.5
41
GearboxWeight
ø 19x40 6 M6x1621.5
311A
12
EN Unit 411A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
38NmOne Step
FR (N)
The dynamic efficiency is 0.98 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
891493425362303222170129
1.572.843.293.874.626.308.2210.86
1.51.51.51.51.51.10.550.37
1.31.21.21.01.01.01.31.0
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
910FRFA
1827001000200600
11502304001250250300
14502902001600320140
Feq = FR . 40X+20
FRFAn2 FRFAn2
Ratioscode
ø
Standardø19
On requestø14ø24
284419541756155813601063974776
Output Shaft
0102030405060708
1628333946463027
= =
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
120024014001400280900
FRFAn1
LUBRICATION 411A Oil Quantity 0.10 Lt.
n2
FA (N)
-B -C -D -E
63 71 80 90
BBBBBBBB
Available B5Motor Flanges
-Q -R
71 80
-T
90
CCCCCCCC
CCCCCCCC
Available B14Motor Flanges
P1R
For all details on lubrication and plugs please consult with a Regalrepresentative or office
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
M2R
1.91.81.71.51.51.10.690.39
2035384047463828
411A Rating - Aluminium ONE STEP GEARBOXES
13
38NmOne Step
e1
s1
k1
ø19 h6
b1 f 7
c1f1
a1
36.5
ø75
P411-F...
Kit Code
P411-H1... With Feet
Output Flange
R411-N... Input Shaft
Available output flangesa1 ø b1
P411-N... Basic Gearbox
c1 e1 f1 s1120 80
95110130
140160200
11.511.511.511.5
33
3.53.5
9*9911
KC309010KC309011KC309012KC309013
d1
3.5
Detail Y
h1
38
g6
A101
4049.5
30ø19 h6
ø60
h8
N. 4 - M8x14
35
N. 4 - M8x15 32 26
6
21.5
g6
40
*See the table of output shaft for the complete list of diameters
M6x16
standard
*Holes position
Detail Y
M6x1635
112.5
6
21.5
132110
75
41
113
13911018
ø9
35
3.20 kg
x
p1
M6x16
ø19 h6
*Available output shaft
On requestø 19x40Standard
Shaft - d1 p16 M6x16
ø 24x40 8 M6x16
h121.5
27
x
ø 14x30 5 M5x1316
Kit CodeB14 MotorFlanges A g6 k171 B1480 B1490 B14
119.5121.5121.5
120140
105 123125125
K0634047K0634046K0634041
Kit CodeB5 MotorFlanges A g6 k163 B571 B5
80/90 B5
121.5119.5121.5
160200
140 125123125
K0634041K0634042K0634043
100115130165
GearboxWeight
Kit CodeK4119024LM
411A
14
110NmOne Step
FR (N)
The dynamic efficiency is 0.98 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
1077571423325266184133
1.302.453.314.315.277.6310.50
44443
2.21.1
1.21.11.01.01.11.01.0
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
1470FRFA
2947001600320600
18503704002000400300
23004602002550510140
FRFAn2 FRFAn2
Ratioscode
ø
Standardø28
On requestø19ø24
30392049165313561158861663
Output Shaft
01020304050607
34648711310411177
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
200040014002200440900
FRFAn1
LUBRICATION 511A Oil Quantity 0.29 Lt.
n2
FA (N)
FA (N)
FR (N)
= = X
Feq (N)
Feq = FR . 52.5X+22.5
-R -T -V
80 132
-U
Available B14Motor Flanges
11210090
P1R M2R
For all details on lubrication and plugs please consult with a Regalrepresentative or office
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132
-C -D -E
71 80
BBBBBBB
EN Unit 511A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
Available B5Motor Flanges
90
-F
112100
4.64.34.13.83.12.21.1
40709011011011080
511A Rating - Aluminium ONE STEP GEARBOXES 110NmOne Step
P511-F... Output Flanges
d1
4.5
Detail Y
h1
P511A-H1. R511A-N... Input Shaft
P511-N... Basic Gearbox
A
5
N.1 - ø8
ø28 h6
ø66
h8
50
40
49
80N.4 - M10x16
g6
N.5 - M8x18
49
127
36.361
a1
g6
c1
45.5
f1
s1
b1 f 7
k1
e1
50
50
55
90
16813025
ø10
110
140
132
M6x16
ø24
h6
139
27
8
5.00 kg
x
p1
*Available output shaft
On requestø 28x50Standard
Shaft - d1 p18 M10x22
ø 19x40 6 M6x16
h131
21.5
x
ø 24x50 8 M8x1927
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130180
140160200250
100115130165215
333
3.53.5
9991114
KC409010KC409011KC409012KC409013KC409014
8
31
M10x22
Kit CodeB14 MotorFlanges A g6 k180 B1490 B14
132 B14
147.5147.5
174.5
140
200
120 152152
179
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A g6 k171 B5
80/90 B5100/112 B5
145.5147.5156.5
200250
160 150152161
KC0234041KC0234042KC0234043 100/112 B14 156.5 160 161 KC0854047
Detail Y
ø28 h6
M10x22*See the table of output shaft for the complete list of diameters
10101011
11.5
33.5
Kit CodeK5119023LM
132 B5 174.5 300 179 KC504043
GearboxWeight
With Feet
511A
15
110NmOne Step
FR (N)
The dynamic efficiency is 0.98 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
1077571423325266184133
1.302.453.314.315.277.6310.50
44443
2.21.1
1.21.11.01.01.11.01.0
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
1470FRFA
2947001600320600
18503704002000400300
23004602002550510140
FRFAn2 FRFAn2
Ratioscode
ø
Standardø28
On requestø19ø24
30392049165313561158861663
Output Shaft
01020304050607
34648711310411177
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
200040014002200440900
FRFAn1
LUBRICATION 511A Oil Quantity 0.29 Lt.
n2
FA (N)
FA (N)
FR (N)
= = X
Feq (N)
Feq = FR . 52.5X+22.5
-R -T -V
80 132
-U
Available B14Motor Flanges
11210090
P1R M2R
For all details on lubrication and plugs please consult with a Regalrepresentative or office
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132
-C -D -E
71 80
BBBBBBB
EN Unit 511A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
Available B5Motor Flanges
90
-F
112100
4.64.34.13.83.12.21.1
40709011011011080
511A Rating - Aluminium ONE STEP GEARBOXES 110NmOne Step
P511-F... Output Flanges
d1
4.5
Detail Y
h1
P511A-H1. R511A-N... Input Shaft
P511-N... Basic Gearbox
A
5
N.1 - ø8
ø28 h6
ø66
h8
50
40
49
80N.4 - M10x16
g6
N.5 - M8x18
49
127
36.361
a1
g6
c1
45.5
f1
s1
b1 f 7
k1
e1
50
50
55
90
16813025
ø10
110
140
132
M6x16
ø24
h6
139
27
8
5.00 kg
x
p1
*Available output shaft
On requestø 28x50Standard
Shaft - d1 p18 M10x22
ø 19x40 6 M6x16
h131
21.5
x
ø 24x50 8 M8x1927
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130180
140160200250
100115130165215
333
3.53.5
9991114
KC409010KC409011KC409012KC409013KC409014
8
31
M10x22
Kit CodeB14 MotorFlanges A g6 k180 B1490 B14
132 B14
147.5147.5
174.5
140
200
120 152152
179
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A g6 k171 B5
80/90 B5100/112 B5
145.5147.5156.5
200250
160 150152161
KC0234041KC0234042KC0234043 100/112 B14 156.5 160 161 KC0854047
Detail Y
ø28 h6
M10x22*See the table of output shaft for the complete list of diameters
10101011
11.5
33.5
Kit CodeK5119023LM
132 B5 174.5 300 179 KC504043
GearboxWeight
With Feet
511A
16
FeetRemovable feetwith patented lockingsystem.
FlangeFully modular to IEC andcompact integratedmotor.NEMA C flange.
GearsHardened and ground gears.
Foot prints Compatible to the mainstandard of the market.
Oil sealsTwo oil sealson request.
Output shaftWith wellproportionedbearings.
Single piece aluminiumalloy housing
Combines light weight withhigh tensile strength.
Precision machined foralignment of bearings
and gearing.
Removableinspection coverAllows periodic inspectionof gearing during routinemaintenance.
Alloy housingIs vacuum impregnated (MIL-STD 276) forprotection and sealing. No secondaryfinish required but readily accepts paint.
A modular and compact product
Lubricated for life with
synthetic oil with operative rangefrom -15° to +130°C.
Aluminium Inline Gearboxes
17
FeetRemovable feetwith patented lockingsystem.
FlangeFully modular to IEC andcompact integratedmotor.NEMA C flange.
GearsHardened and ground gears.
Foot prints Compatible to the mainstandard of the market.
Oil sealsTwo oil sealson request.
Output shaftWith wellproportionedbearings.
Single piece aluminiumalloy housing
Combines light weight withhigh tensile strength.
Precision machined foralignment of bearings
and gearing.
Removableinspection coverAllows periodic inspectionof gearing during routinemaintenance.
Alloy housingIs vacuum impregnated (MIL-STD 276) forprotection and sealing. No secondaryfinish required but readily accepts paint.
A modular and compact product
Lubricated for life with
synthetic oil with operative rangefrom -15° to +130°C.
Aluminium Inline Gearboxes
18
P -F402A3
403A503A603A
202A302A402A452A502A602A
2
Output flange mounted
StagesAluminium coaxial gearboxes
-FYou see feet code in the chart of the dimensions
FeetCode
FeetMarket
reference G H R L L1 S1818182525
112212/3
1727
42/3
85100759080
110130110110
110÷120
87107.590+2013085
50
L4L5
1316
0405
80100
105125
B..-N
BR
PM
Stages
Modular base
With IEC motor
With male input shaft
With motor flange Without flange / feet
MountingSizeType
On request we can deliver our products according to the ATEX.
Mounted feet
B1B2S1S2M1
HOW TO ORDER
19
P -F402A3
403A503A603A
202A302A402A452A502A602A
2
Output flange mounted
StagesAluminium coaxial gearboxes
-FYou see feet code in the chart of the dimensions
FeetCode
FeetMarket
reference G H R L L1 S1818182525
112212/3
1727
42/3
85100759080
110130110110
110÷120
87107.590+2013085
50
L4L5
1316
0405
80100
105125
B..-N
BR
PM
Stages
Modular base
With IEC motor
With male input shaft
With motor flange Without flange / feet
MountingSizeType
On request we can deliver our products according to the ATEX.
Mounted feet
B1B2S1S2M1
HOW TO ORDER
ø40
202A 403A
402A 403A
602A 603A
GHILM
ø30ø35ø38
302A
Ø25
SBDV
Ø14Ø16Ø20
ø20
202A
SBCDEVG
ø14ø16
ø24ø25ø28
ø19
ø30
452A502A 503A
EVGHI
ø24ø25
ø35
2V
D
A
-V=132(ø200)
-T=90(ø140)
-P=63(ø90)
-O=56(ø80)
-R=80(ø120)
-Q=71(ø105)
B-C
B
C
STANDARD
B37.33
Specify only for vertical positions
B14
B5
-F=100÷112(ø250)
-E=90(ø200)
-B=63(ø140)
-A=56(ø120)
-D=80(ø200)
-C=71(ø160)
202A 302A
ø20
BCDEV
ø16
ø24ø25
ø19
ø200
N Without flange
ø140ø160
452A502A 503A
345
ø160ø200ø250
ø1201234
602A 603A
345
ø160ø200ø250
302A 402A 503A 603A
-3 ø24(90B5)
452A 502A602A
-0 ø11(63B5)
-2 ø19(80B5)
STANDARD
302A 402A 503A 603A
-3 ø24
452A 502A602A
-1 ø14
202A 403A
-2 ø19
ø14(71B5)
ø9(56B5)
ø28(100B5)
ø19(80B5)
ø24(90B5)
ø14(71B5)
-3
-1
-1
-Z
-4
-2-U=100÷112(ø160)
B6
B8
V8
B7
V5
V6
ø
ø
See technical data table
STANDARD
ø28
ø28
B3
402A 403A
ø200
ø140ø160
ø12012345 ø250
Ratio Output FlangeOutput Shaft Motor Size Terminal BoxPosition
MountingPosition
-G=132(ø300)
ø
øø
HOW TO ORDER
Flange
Type R
Without flange
20
9550P [KW] =M [Nm] n [rpm]
1000P [KW] =M [Kg] g [9.81] v [m / s]
1000P [KW] =F [N] v [m / s]
FR
M
FR
d [mm]fK
M [Nm] 2000FR [N] =
n [rpm]M [lb in] =63030 P[HP]
n [rpm]M [Nm] =9550 P[KW]
d [in]fK
M [lb in] 8.9FR [N] =
d
Rotation
Linear movement
Lifting
— If your application requires higher radial loads, contact your local Regal sales office or sales representative. Higher load may be possible.
REQUIRED POWER
Factor
Output torque
Diameter of driving element
1.15 Gear wheels1.25 Chain sprockets1.75 Narrow v-belt pulley2.50 Flat-belt pulley
- Radial load generated by external transmissions keyed onto input and/or output shafts.
TORQUE
fK
USEFUL FORMULAS
RADIAL LOADS
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -D -E -Q -R -U
63 71 80* 90* 71 80
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-T
112398320252220191
3.524.375.556.367.33
333
2.22.2
1.21.00.91.01.1
BBBBB
Ratioscode
ø
28212818281319212812
Output Shaft
0102030405
6986
10992
106
Available B5Motor Flanges
Available B14Motor Flanges
QUICK SELECTION Input Speed (n1) = 1400 min-1
90 100
CCCCC
CCCCC
P1R M2R
3.53.12.82.32.5
8090
10095
120
B
A
C
D
B)
C)
B)
Type of load and starts per hour Operating hours per day
3 h 10 h 24 h
≤ 10
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
HOW TO SELECT A GEARBOX
160NmCoaxial - Gear402A Rating - Aluminium COAXIAL GEARBOXES
21
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -D -E -Q -R -U
63 71 80* 90* 71 80
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-T
112398320252220191
3.524.375.556.367.33
333
2.22.2
1.21.00.91.01.1
BBBBB
Ratioscode
ø
28212818281319212812
Output Shaft
0102030405
698610992106
Available B5Motor Flanges
Available B14Motor Flanges
QUICK SELECTION Input Speed (n1) = 1400 min-1
90 100
CCCCC
CCCCC
P1R M2R
3.53.12.82.32.5
809010095120
B
A
C
D
B)
C)
B)
Type of load and starts per hour Operating hours per day
3 h 10 h 24 h
≤ 10
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
HOW TO SELECT A GEARBOX
160NmCoaxial - Gear402A Rating - Aluminium COAXIAL GEARBOXES
22
** Concerning a reduced dimensions electric motor.
70NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
FR (N)
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -O -P
63 71* 56 63
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-Q
407327257225194181142123107938675666453
48.539
37.129.928.122.6
3.444.285.456.237.207.749.8511.4213.0315.1016.2018.7821.1521.8426.3128.8835.9137.6946.8749.7661.89
0.55**0.55**0.55**0.55**0.55**0.55**0.55**0.55**0.55**0.370.370.370.370.370.370.370.370.250.250.250.18
2.01.92.02.01.91.81.71.51.31.61.51.31.21.10.91.00.81.10.90.90.9
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
700FRFA
140300756151250924185200
13202461401350270120150030085
170034070190038040
--15
Feq = FR . 35.7X+20.7
FRFAn2 FRFAn2
Ratioscode
ø
Standardø16
ø14ø20ø25
On request
28212818281519212812191819151715191217121910171013121015131010121010912910712710
Output Shaft
010203040506070809101112131415161718192021
121520232628364147373945515364708762778177
= =
Available B5Motor Flanges
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
7001401400800160900950190500
FRFAn1
FA (N)
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
71
CCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCC
EN Unit 202A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
n2
LUBRICATION 202A Oil Quantity 0.15 Lt.
P1R
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
M2R
1.11.11.11.11.10.990.930.800.700.610.570.490.430.420.350.370.300.280.230.210.17
253040455050606060606060606060707070707070
202A Rating - Aluminium COAXIAL GEARBOXES
23
With flange 3.3 kgWith feet 3.7 Kg
70NmCoaxial - Gear
81.5
41
128
Kit CodeB14 MotorFlanges A Cmax
g6 k156 B1463 B1471 B14
133.3135.8133.3
139146
152.590105
80 136.8139.3136.8
KC404049K0504047K0504045
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
135.8133.3
170180 160
140 139.3136.8
K0504041K0504042
P202A-N... Basic Gearbox R202A-N... Input Shaft
*Available output shaft
On request
ø 16x40Standard
Shaft - d1 p1
x
5 M6x16
FeetCode
MarketReference G H R L L1 S H1 O øI S2 only with
motor flangeB5 max.Flange Other feet are available,
consult Regal.
L3L4
181818
12.513
112212/317-32
0304
85100756580
11013011091105
87107.51106076
506050--
130155130105132
125145
115.5149165
1551555
911999
63B5
-
A see on page bottom
d1
3.5
Detail Y
h1
60.5
e1
s1
N.4 - M8X16
ø14
h6
b1 f 7
f1
a1
36.5 c1
Detail Y
5
16
2.4
26
3.5
70
130
70
25
20
M5X13
N.4 M8x14
90°
k1
A
p1
M6x16
ø16 h6
With flange andfeet only on
request.Ask for
compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130
140160200
100115130165
11.511.511.511.5
33
3.53.5
9*9911
KC309010KC309011KC309012KC309013
ø 14x30 56
M6x16M8x19ø 20x40
ø 25x50 8 M8x19
A
18
5
M6x16
ø16 h6*See the table of output shaft for the complete list of diameters
117.3
G OøI
3 30
40 9.5
LL1
Cm
ax
S
H1
R
3.5
H
80
ø75
117.3
g6
3 30
40
6.5
P202A-F... Output Flanges
P202AB1... With Feet
ø75
g6
48
-
* Holes position
18
5
h11816
22.528
x
Most popular types
S2
9.5 ø60
h8
g6
Kit CodeKC309022
KC309023LMKC309024
KC309026LMKC309027LM
GearboxWeight
11.5 71B5 -
-
-
-
-
-
202A
B1B2S1
24
EN Unit 302A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
120NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -D -E -Q -R
63 71* 80* 90* 71 80
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-T
90
407327257225194181142123107938675666453
48.539
37.129.928.122.6
3.444.285.456.237.207.749.8511.4213.0315.1016.2018.7821.1521.8426.3128.8835.9137.6946.8749.7661.89
1.51.51.51.51.51.51.51.51.11.10.750.750.750.750.550.550.370.370.370.250.25
1.01.01.01.11.01.11.01.01.21.11.31.21.11.11.11.11.21.10.91.21.1
BBBBBBBBBBBBBBBBBBBBB
Ratioscode
ø
Standardø20
ø14ø16ø19ø20ø24ø25ø28
On request
28212818281519212812191819151715191217121910171013121015131010121010912910712710
Output Shaft
010203040506070809101112131415161718192021
3442536171769711293108809210410795105879111381101
Available B5Motor Flanges
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
700FRFA
140300756151250924185200
13202461401350270120150030085
170034070190038040
--15
FRFAn2 FRFAn2
= =
1130226140013202649001610322500
FRFAn1
n2
FA (N)
CCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCC
Feq = FR . 35.7X+20.7
LUBRICATION 302A Oil Quantity 0.15 Lt.
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
M2RP1R
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
1.61.41.51.71.51.61.51.51.31.21.00.870.820.830.620.600.460.410.350.310.26
35405270708095115114114107107114119107114107102107101107
302A Rating - Aluminium COAXIAL GEARBOXES
4A see on page bottom
Most popular types
Kit CodeKC309022
KC309023LMKC309024
KC309025LMKC309026LMKC309027LM
Other feet are available,consult Regal.
120NmCoaxial - Gear
81.5
41
128
Kit CodeB14 MotorFlanges A Cmax
g6 k171 B1480 B1490 B14
149.7151.7151.7
152.5160170
120140
105 153.2155.2155.2
K0634047K0634046K0634041
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
151.7149.7151.7
170180200
160200
140 155.2153.2155.2
K0634041K0634042K0634043
P302A-N... Basic Gearbox R302A-N... Input Shaft
*Available output shaft
On request
ø 20x40Standard
ø 25x50
Shaft - d1 p1
x
6
88
M8x19
M8x19M8x19
FeetCode
Marketreference G H R L L1 S H1 O øI S2 only with
motor flangeB5 max.Flange
3.5 80/90B5
L3L4
18181825
12.513
112212/317-32
270304
8510075906580
11013011011091
105
87107.51101306076
506050---
130155130130105132
125145
115.5135149165
155
15555
9119999
-
31.5 80/90B5
16.5 80/90B5
d1
3.5
Detail Y
h1
60.5
e1
s1
N.4 - M8x16
ø19
h6
b1 f 7
f1
a1
36.5 c1
Detail Y
6
21.5
2.5
26
3.5ø6
0 h8 143.5
70
35
30
M6x16
N.4 M8x14
90°
k1
A
p1
M8x19
ø20 h6
With flange andfeet only on
request.Ask for
compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130
140160200
100115130165
11.511.511.511.5
33
3.53.5
9*9911
KC309010KC309011KC309012KC309013ø 28x50
ø 14x30 55
M6x16M6x16ø 16x40
ø 19x40 6 M6x16
A
22.5
6
M8x19
ø20 h6*See the table of output shaft for the complete list of diameters
131.2
G
S2øI
3 30
40 9.5
LL1
Cm
ax
S
H1
R
3.5
H
80
ø75
131.2
g6
3 30
40 9.5
P302A-F... Output Flanges
P302AB1... With Feet
ø75
g6
48
15 80/90B5
* Holes position
22.5
6
h122.5
2831
1618
21.5
x
O
-
8 M8x19ø 24x50 27
6.5
GearboxWeight
70
g6
With flange 3.5 kgWith feet 4.0 Kg
-
5 71B5
71B5
71B5
-
-
302A
B1B2S1S2
25
A see on page bottom
Most popular types
Kit CodeKC309022
KC309023LMKC309024
KC309025LMKC309026LMKC309027LM
Other feet are available,consult Regal.
120NmCoaxial - Gear
81.5
41
128
Kit CodeB14 MotorFlanges A Cmax
g6 k171 B1480 B1490 B14
149.7151.7151.7
152.5160170
120140
105 153.2155.2155.2
K0634047K0634046K0634041
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
151.7149.7151.7
170180200
160200
140 155.2153.2155.2
K0634041K0634042K0634043
P302A-N... Basic Gearbox R302A-N... Input Shaft
*Available output shaft
On request
ø 20x40Standard
ø 25x50
Shaft - d1 p1
x
6
88
M8x19
M8x19M8x19
FeetCode
Marketreference G H R L L1 S H1 O øI S2 only with
motor flangeB5 max.Flange
3.5 80/90B5
L3L4
18181825
12.513
112212/317-32
270304
8510075906580
11013011011091105
87107.51101306076
506050---
130155130130105132
125145
115.5135149165
15515555
9119999
-
31.5 80/90B5
16.5 80/90B5
d1
3.5
Detail Y
h1
60.5
e1
s1
N.4 - M8x16
ø19
h6
b1 f 7
f1
a1
36.5 c1
Detail Y
6
21.5
2.5
26
3.5ø6
0 h8 143.5
70
35
30
M6x16
N.4 M8x14
90°
k1
A
p1
M8x19
ø20 h6
With flange andfeet only on
request.Ask for
compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130
140160200
100115130165
11.511.511.511.5
33
3.53.5
9*9911
KC309010KC309011KC309012KC309013ø 28x50
ø 14x30 55
M6x16M6x16ø 16x40
ø 19x40 6 M6x16
A
22.5
6
M8x19
ø20 h6*See the table of output shaft for the complete list of diameters
131.2
G
S2øI
3 30
40 9.5
LL1
Cm
ax
S
H1
R
3.5
H
80
ø75
131.2
g6
3 30
40 9.5
P302A-F... Output Flanges
P302AB1... With Feet
ø75
g6
48
15 80/90B5
* Holes position
22.5
6
h122.5
2831
1618
21.5
x
O
-
8 M8x19ø 24x50 27
6.5
GearboxWeight
70
g6
With flange 3.5 kgWith feet 4.0 Kg
-
5 71B5
71B5
71B5
-
-
302A
B1B2S1S2
26
EN Unit 402A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
160NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-Q -R -U
71 80
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-T
11239832125222019117713912010610291867875656353
47.639
36.529.927.622.6
3.524.375.566.367.337.8910.0611.6613.2613.6815.3716.2018.0418.7821.5422.2926.3129.4035.9138.3746.8750.6761.89
333
2.22.22.22.21.51.51.51.51.51.51.11.11.10.750.750.550.550.550.370.37
1.21.10.91.11.21.11.01.51.21.11.10.90.91.01.01.01.11.11.11.20.81.10.9
Ratioscode
ø
Standardø25
ø16ø19ø20ø24
On request
2821281828131921281219181913171319121513171219101512171013121013131010121010912910712710
Output Shaft
0102030405060809102511122324141516171819202122
688410790104112143114130134151159177134154160129144130139170123150
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
90
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
1550FRFA
31030016503302501800360200
20304061402240448120240048085
270054070300060040300060015
Feq = FR . 46X+21
FRFAn2 FRFAn2
= =
0.25 LT 0.30 LT 0.40 LT 0.40 LT 0.40 LT 0.50 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
1200240140014002809001700340500
FRFAn1
n2
FA (N)
100
CCCCCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCCCCC
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
P1R M2R
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
90*100*112
-F-B -C -D
63 71
BBBBBBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
80*
-E
3.53.12.72.32.52.32.32.31.81.61.61.31.41.11.11.10.800.830.590.640.450.400.34
809010095120120150174160144160138160138160167138160138160138132138
402A Rating - Aluminium COAXIAL GEARBOXES
100/112 B5 195.8 232 250 199.8 KC404043
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC359021KC409025KC409022
KC409026KC409023
KC359023LMKC409027LM
With flange 5.7 kgWith feet 5.9 Kg
160NmCoaxial - Gear
160.5A
A
With flange andfeet only on
request.Ask for
compatibility
P402A-F...
Kit Code
P402A-N... Basic Gearbox
Output Flanges
Kit Code
R402A-N... Input Shaft
FeetCode
B14 MotorFlanges A Cmax
g6 k1
*Available output shaftAvailable output flanges
a1 ø b1
FeetMarket
Reference G H R L L1 S H1 O øI S2 only withmotor flange
B5 max.Flange
28 100/112B5
P402AB1... With Feet
71 B1480 B1490 B14
100/112 B14
179181181
195.8
159.5167177187
120140160
105 183185185
199.8
K0634047K0634046K0634041KC404041
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
181179181
177187207
160200
140 185183185
K0634041K0634.042K0634043
c1 e1 f1 s1120 80
95110130180
140160200250
100115130165215
333
3.53.5
7991114
KC409010KC409011KC409012KC409013KC409014
181818
2525
112212/3
17
022-22342/3
8510075
10080
110130110
110110÷120
87107.5
90÷110
11585
506050
--
130155145
145145
167182155
182162
151715
2015
-119
99
18 100/112B5
18 100/112B5
160.550403
M8x19G L1
LRS
139
ø25 h6
g6
C m
axS
2 O
H
H1
standard
8
28
b1 f 7
c1
k1
f1
Detail Y
a1
47
8.2
403 6
ø25
h6 21.5
60
171.3 35
30
M6x16
2.5M10x18
37 ø19
h6
828 50
ø8
127
ø80
45.550°
11.5
139Input shaftN.5 M8x17
M8x19 65°
s1
e1
d1
4
Detail Y
h1
øI
g6
45.5 32.5
7
7
7
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
x
p1
On request
ø 25x50Standard
Shaft - d1 p18 M8x19
6 M8x19ø 20x40
h128
22.5
x
L4L5
1316
0405
80100
105125
7690
--
132150
162182
56
1012
-18 100/112B5
-
----
-
5 M6x16ø 16x40ø 19x40 6 M6x16
1821.5
10101011
11.5
ø66
h8
g6
GearboxWeight
ø 24x50 8 M8x1927
KC4090242527 90 110 130 - 145 172 20 9 -3 80/90B5
33 100/112B58 80/90B5
38 100/112B513 80/90B5
43 100/112B518 80/90B5
38 100/112B513 80/90B5
402A
B1B2S1
H2M1
S2
27
100/112 B5 195.8 232 250 199.8 KC404043
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC359021KC409025KC409022
KC409026KC409023
KC359023LMKC409027LM
With flange 5.7 kgWith feet 5.9 Kg
160NmCoaxial - Gear
160.5A
A
With flange andfeet only on
request.Ask for
compatibility
P402A-F...
Kit Code
P402A-N... Basic Gearbox
Output Flanges
Kit Code
R402A-N... Input Shaft
FeetCode
B14 MotorFlanges A Cmax
g6 k1
*Available output shaftAvailable output flanges
a1 ø b1
FeetMarket
Reference G H R L L1 S H1 O øI S2 only withmotor flange
B5 max.Flange
28 100/112B5
P402AB1... With Feet
71 B1480 B1490 B14
100/112 B14
179181181
195.8
159.5167177187
120140160
105 183185185
199.8
K0634047K0634046K0634041KC404041
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
181179181
177187207
160200
140 185183185
K0634041K0634.042K0634043
c1 e1 f1 s1120 80
95110130180
140160200250
100115130165215
333
3.53.5
7991114
KC409010KC409011KC409012KC409013KC409014
181818
2525
112212/3
17
022-22342/3
8510075
10080
110130110
110110÷120
87107.5
90÷110
11585
506050
--
130155145
145145
167182155
182162
151715
2015
-119
99
18 100/112B5
18 100/112B5
160.550403
M8x19G L1
LRS
139
ø25 h6
g6
C m
axS
2 O
H
H1
standard
8
28
b1 f 7
c1
k1
f1
Detail Y
a1
47
8.2
403 6
ø25
h6 21.5
60
171.3 35
30
M6x16
2.5M10x18
37 ø19
h6
8
28 50
ø8
127
ø80
45.550°
11.5
139Input shaftN.5 M8x17
M8x19 65°
s1
e1
d1
4
Detail Y
h1
øI
g6
45.5 32.5
7
7
7
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
x
p1
On request
ø 25x50Standard
Shaft - d1 p18 M8x19
6 M8x19ø 20x40
h128
22.5
x
L4L5
1316
0405
80100
105125
7690
--
132150
162182
56
1012
-18 100/112B5
-
----
-
5 M6x16ø 16x40ø 19x40 6 M6x16
1821.5
10101011
11.5
ø66
h8
g6
GearboxWeight
ø 24x50 8 M8x1927
KC4090242527 90 110 130 - 145 172 20 9 -3 80/90B5
33 100/112B58 80/90B5
38 100/112B513 80/90B5
43 100/112B518 80/90B5
38 100/112B513 80/90B5
402A
B1B2S1
H2M1
S2
28
EN Unit 403A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
160NmCoaxial - Gear
The dynamic efficiency is 0.94 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
36.532.027.626.222.922.619.719.118.716.214.513.611.110.38.47.96.5
38.4043.6950.6453.3661.2161.8570.9573.4374.7786.6696.85102.89126.40135.69165.74177.09216.31
0.370.370.370.370.370.370.370.370.250.250.250.250.180.180.120.120.09
1.91.41.31.11.10.91.01.01.21.01.01.11.01.01.11.11.0
Ratioscode
ø
17171319171217171219171019131217171013171210171319131013171010171210131391712
1013121013109131291310
Output Shaft
0203040506070809101112131715161819
91104120127145147168174120139155165155166131140136
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
1550FRFA
31030016503302501800360200
20304061402240448120240048085
270054070300060040300060015
Feq = FR . 46X+21
FRFAn2 FRFAn2
= =
0.30 LT 0.35 LT 0.45 LT 0.45 LT 0.45 LT 0.55 LT AskB3 B6 B7 B8 V5 V6 V8
Standardsupplied
For these mounting position specify in the order or add oil
7001401400800160900950190500
FRFAn1
n2
FA (N)
Standardø25
ø16ø19ø20ø24
On request
-B -C -O -P
63 71 56 63
-Q
Available B5Motor Flanges
Available B14Motor Flanges
71
CCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCC
P1R
For all details on lubrication and plugs please consult with a Regaloffice or representative.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
M2R
0.710.530.490.400.410.350.350.370.290.250.260.270.200.180.130.140.10
175149160138160138160175138138160180160160138160138
403A Rating - Aluminium COAXIAL GEARBOXESWith flange 6.1 kgWith feet 6.3 Kg
160NmCoaxial - Gear
166.5A
A
P403A-F...
P403A-N... Basic Gearbox
Output flanges
R403A-N... Input Shaft
P403AB1... With Feet
166.550403
M8x19G L1
LRS
139
ø25 h6
g6
C m
axS
2 O
H
H1
standard
8
28
b1 f 7
c1
k1
f1
Detail Y
a1
47
8.2
403 5
ø25
h6 16
ø66
h8
175.7 25
20
M5x13
2.5M10x18
37
ø14
h6
828 50
ø8
127
ø80
45.550°
11.5
139Input shaftN.5 M8x17
M8x19 65°
s1
e1
d1
4
Detail Y
h1
øI
g6
45.5 32.5
3.2
3.2
3.2
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
Kit CodeB14 MotorFlanges A Cmax
g6 k156 B1463 B1471 B14
182.5185
182.5
143.2148.2155.7
90105
80 186.5189
186.5
KC404049K0504047K0504045
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
185182.5
173.2183.2 160
140 189186.5
K0504041K0504042
x
p1
With flange andfeet only on
request.Ask for
compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130180
140160200250
100115130165215
333
3.53.5
7991114
KC409010KC409011KC409012KC409013KC409014
*Available output shaft
On request
ø 25x50Standard
Shaft - d1 p18 M8x19
6 M8x19ø 20x40ø 24x50 8 M8x19
h128
22.527
x
5 M6x16ø 16x40ø 19x40 6 M6x16
1821.5
60
10101011
11.5
g6
Other feet are available,consult Regal.
A see on page bottomMost popular types
Feet
403AGearboxWeight
Kit CodeKC359021KC409025KC409022
KC409026KC409023
KC359023LMKC409027LM
FeetCode
MarketReference G H R L L1 S H1 O øI S2 only with
motor flangeB5 max.Flange
-181818
2525
112212/3
17
022-22342/3
8510075
10080
110130110
110110÷120
87107.5
90÷110
11585
506050
--
130155145
145145
167182155
182162
151715
2015
-119
99
-
--
L4L5
1316
0405
80100
105125
7690
--
132150
162182
56
1012
-
2 80/90B5
--
-
----
KC4090242527 90 110 130 - 145 172 20 9 - -
-B1B2S1
H2M1
S2
29
With flange 6.1 kgWith feet 6.3 Kg
160NmCoaxial - Gear
166.5A
A
P403A-F...
P403A-N... Basic Gearbox
Output flanges
R403A-N... Input Shaft
P403AB1... With Feet
166.550403
M8x19G L1
LRS
139
ø25 h6
g6
C m
axS
2 O
H
H1
standard
8
28
b1 f 7
c1
k1
f1
Detail Y
a1
47
8.2
403 5
ø25
h6 16
ø66
h8
175.7 25
20
M5x13
2.5M10x18
37
ø14
h6
8
28 50
ø8
127
ø80
45.550°
11.5
139Input shaftN.5 M8x17
M8x19 65°
s1
e1
d1
4
Detail Y
h1
øI
g6
45.5 32.5
3.2
3.2
3.2
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
Kit CodeB14 MotorFlanges A Cmax
g6 k156 B1463 B1471 B14
182.5185
182.5
143.2148.2155.7
90105
80 186.5189
186.5
KC404049K0504047K0504045
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
185182.5
173.2183.2 160
140 189186.5
K0504041K0504042
x
p1
With flange andfeet only on
request.Ask for
compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1120 80
95110130180
140160200250
100115130165215
333
3.53.5
7991114
KC409010KC409011KC409012KC409013KC409014
*Available output shaft
On request
ø 25x50Standard
Shaft - d1 p18 M8x19
6 M8x19ø 20x40ø 24x50 8 M8x19
h128
22.527
x
5 M6x16ø 16x40ø 19x40 6 M6x16
1821.5
60
10101011
11.5
g6
Other feet are available,consult Regal.
A see on page bottomMost popular types
Feet
403AGearboxWeight
Kit CodeKC359021KC409025KC409022
KC409026KC409023
KC359023LMKC409027LM
FeetCode
MarketReference G H R L L1 S H1 O øI S2 only with
motor flangeB5 max.Flange
-181818
2525
112212/3
17
022-22342/3
8510075
10080
110130110
110110÷120
87107.5
90÷110
11585
506050
--
130155145
145145
167182155
182162
151715
2015
-119
99
-
--
L4L5
1316
0405
80100
105125
7690
--
132150
162182
56
1012
-
2 80/90B5
--
-
----
KC4090242527 90 110 130 - 145 172 20 9 - -
-B1B2S1
H2M1
S2
30
EN Unit 452A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
300NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-R -V-U
80 132100
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
11238833127923120617614812299847056
47.639.334.631.728.623.0
3.614.235.016.076.817.969.4511.4314.2116.6220.1024.9829.4135.5840.5044.2349.0060.90
4444444433
2.21.851.51.51.11.10.750.75
1.61.61.61.61.61.51.31.01.00.91.00.91.10.91.00.81.20.9
Ratioscode
ø
Standardø30
ø24ø25ø28ø35
On request
301830163014301220182016201420122010131413121310814812614810612610
Output Shaft
010203040506070809101112131415161718
93108129156175204242293274321286302288349290316240299
Available B14Motor Flanges
0.31 LT 0.31 LT 0.31 LT 0.31 LT 0.31 LT 0.31 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T
90
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
X
FA (N)
FR (N)Feq (N)
2070FRFA
41530021604302502340470200
27005401402790560120315063085
351070070405081040450090015
Feq = FR . 51X+21
FRFAn2 FRFAn2
= =
2000400140022004409002200440500
FRFAn1
n2
FA (N)
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
P1R M2R
For all details on lubrication and plugs please consult with a Regaloffice or representative.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132*
-C -D -E
71 80
BBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
112100*
6.36.16.16.36.25.84.94.02.82.82.31.61.61.31.10.920.930.66
150170200250277300304300265304300265304300290265300265
452A Rating - Aluminium COAXIAL GEARBOXES
KC509028LM
15 100/112B53052/3 110 135÷150 100 190 173 18 -
300NmCoaxial - Gear
With flange 8.7 kgWith feet 8.9 Kg
8
Kit CodeB14 MotorFlanges A Cmax
g6 k1 with KC509011
80 B1490 B14
100/112 B14
197.7197.7206.7
202212222
140160
120 206.2206.2215.2
KC0854046KC0854045KC0854047
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
195.7197.7206.7
222242267
200250
160 198.2200.2209.2
KC0234041KC0234042KC0234043
With flange and feet only on request.
Ask for compatibility
Kit Code
P452A-N... Basic Gearbox R452A-N... Input Shaft
Available output flangesa1 ø b1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
FeetCode
FeetMarket
Reference G H R L S H1 O øI S2 only withmotor flange
B5 max.Flange
18203030
19
312/330/3547-57
023-233
06
110130115130
125
160180135135
160
130149.5165135
106
190216170185
205
173193178193
188
20182425
8
--
--
-
d1
2.5
Detail Y
h1
H1
S
4
83
R
A
110.5
e1
O
H
s1
N.4 - M12x20
ø24
h6
b1 f 7
f1
a1
k1
57.5 c1
Detail Y
33
8 5
13.5
5060
øI
15.5
A177.2
g6
L
S2
M10x22
ø30 h6*See the table of output shaft for the complete list of diameters
C m
ax
G
177.2
8
27
5
63
4
124
189.3
78
50
4033
M10x22M6x16
5 5015.5
g6
60
ø30
h6
187
50°
69.5
N.4 M10x18
ø10ø123
132.
5
Suggested B14 motor flange
x
p1
80/90B5
E2 132202/3 100 135 192 164 163 6 -P4 35142 142 130 145 160 205 8 -
71B5
L6
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22ø 24x50 8
8
M8x19
M8x19ø 28x60ø 35x60 10 M10x22
h13327
3138
x
ø 25x50 8 M8x1928
76.5
g6
c11413
15.5
13.5
P452A-F... Output Flanges
P452AB1... With Feet
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC509024KC609024KC509022KC509025KC509023
KC509026LMKC509027LM
132 B14 224.7 242 200 233.2
8.5 with KC509011
k1200.2200.2209.2227.2
51.5 with KC509011
ø106
h8
k1 with KC509011
204.2206.2215.2
GearboxWeight
KC504041132 B5 224.7 292 300 227.2 KC504043 233.2
1413.514
141414
11
1120 132B5
8 132B5
40 132B525 132B5
20 132B5
15 100/112B540 132B5
452A
M2
B3B4S4H3
31
KC509028LM
15 100/112B53052/3 110 135÷150 100 190 173 18 -
300NmCoaxial - Gear
With flange 8.7 kgWith feet 8.9 Kg
8
Kit CodeB14 MotorFlanges A Cmax
g6 k1 with KC509011
80 B1490 B14
100/112 B14
197.7197.7206.7
202212222
140160
120 206.2206.2215.2
KC0854046KC0854045KC0854047
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
195.7197.7206.7
222242267
200250
160 198.2200.2209.2
KC0234041KC0234042KC0234043
With flange and feet only on request.
Ask for compatibility
Kit Code
P452A-N... Basic Gearbox R452A-N... Input Shaft
Available output flangesa1 ø b1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
FeetCode
FeetMarket
Reference G H R L S H1 O øI S2 only withmotor flange
B5 max.Flange
18203030
19
312/330/3547-57
023-233
06
110130115130
125
160180135135
160
130149.5165135
106
190216170185
205
173193178193
188
20182425
8
--
--
-
d1
2.5
Detail Y
h1
H1
S
4
83
R
A
110.5
e1
O
H
s1
N.4 - M12x20
ø24
h6
b1 f 7
f1
a1
k1
57.5 c1
Detail Y
338 5
13.5
5060
øI
15.5
A177.2
g6
L
S2
M10x22
ø30 h6*See the table of output shaft for the complete list of diameters
C m
ax
G
177.2
8
27
5
63
4
124
189.3
78
50
40
33
M10x22M6x16
5 5015.5
g6
60
ø30
h6
187
50°
69.5
N.4 M10x18
ø10ø123
132.
5
Suggested B14 motor flange
x
p1
80/90B5
E2 132202/3 100 135 192 164 163 6 -P4 35142 142 130 145 160 205 8 -
71B5
L6
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22ø 24x50 8
8
M8x19
M8x19ø 28x60ø 35x60 10 M10x22
h13327
3138
x
ø 25x50 8 M8x1928
76.5
g6
c11413
15.5
13.5
P452A-F... Output Flanges
P452AB1... With Feet
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC509024KC609024KC509022KC509025KC509023
KC509026LMKC509027LM
132 B14 224.7 242 200 233.2
8.5 with KC509011
k1200.2200.2209.2227.2
51.5 with KC509011
ø106
h8
k1 with KC509011
204.2206.2215.2
GearboxWeight
KC504041132 B5 224.7 292 300 227.2 KC504043 233.2
1413.514
141414
11
1120 132B5
8 132B5
40 132B525 132B5
20 132B5
15 100/112B540 132B5
452A
M2
B3B4S4H3
32
EN Unit 502A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
350NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
3883312792312061761481229984705756
47.639.334.631.728.623.0
3.614.235.016.076.817.969.4511.4314.2116.6220.1024.6124.9829.4135.5840.5044.2349.0060.90
5.55.55.55.55.55.55.5433
2.22.21.51.51.51.11.11.10.75
1.21.11.11.21.31.21.11.10.91.11.10.91.01.20.91.00.80.90.8
Ratioscode
ø
Standardø30
ø24ø25ø28ø35
On request
3018301630143012201820162014201220101314131211121310814812614810612610
Output Shaft
01020304050708091011122013141516171819
127148176213239279331293274321286350245288349290316351299
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2300FRFA
46030024004802502600520200
30006001403100620120350070085
3900780704500900405000100015
Feq = FR . 54X+24
FRFAn2 FRFAn2
= =
0.45 LT 0.55 LT 1.00 LT 1.10 LT 1.10 LT 1.15 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
2250450140025005009003000600500
FRFAn1
n2
FA (N)
-R -V-U
80 132100112
Available B14Motor Flanges
-T
90
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
P1R M2R
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132*
-C -D -E
71 80
BBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
112100*
6.36.16.16.36.76.35.74.42.73.32.52.01.51.81.41.10.861.00.63
150170200250300330354326250354326326250354326295250326250
502A Rating - Aluminium COAXIAL GEARBOXES
132 B5 256.5 297.3 300 259 KC504043 265
With flange 11.7 kgWith feet 11.9 Kg
350NmCoaxial - Gear
209A
A
P502A-F...
P502A-N... Basic Gearbox
Output Flanges
R502A-N... Input Shaft
P502AB1... With feet
20960505
M10x22G
LRS
178
ø30 h6
g6
C m
axS
2 O
H
H1
standard
8
33
b1 f 7
c1
k1
f1
Detail Y
a1
57.5
12
505 8
ø30
h6 27
78
220.3 50
40
M6x16
5M12x20
63
ø24
h6
833 60
ø10
171
ø123
69.550°
15.5
178N.5 M10x18
M10x22 65°
s1
e1
d1
2.5
Detail Y
h1
øI
g6
40 43
5.3
5.3
5.3
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
3052/3 110 135÷150 100 190 211.5 18
FeetCode
MarketReference G H R L S H1 O øI S2 only with
motor flangeB5 max.Flange
18203030
19
312/330/3547-57
023-233
06
110130115130
125
160180135135
160
130149.5165135
106
190216170185
205
211.5231.5216.5231.5
226.5
20182425
8
-
15 132B5
-
E2 132202/3 100 135 192 164 201.5 6-
P4 35142 142 130 145 160 243.5 8
30 132B5
L6
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
229.5229.5
256.5
207.3217.3
247
140
200
120 232232
259
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
227.5229.5238.5
227.3247.3272.3
200250
160 230232241
KC0234041KC0234042KC0234043 100/112 B14 238.5 227.3 160 241 KC0854047
x
p1
*Available output shaft
20 132B5
On request
ø 30x60StandardShaft - d1 p1
8 M10x22ø 24x50 8
8
M8x19
M8x19ø 28x60ø 35x60 10 M10x22
h13327
3138
x
ø 25x50 8 M8x1928 1413
15.5
124
g6
KC509028LM
Other feet are available,consult Regal
A see on page bottom
Most popular types
Kit CodeKC509024KC609024KC509022KC509025KC509023
KC509026LM
k1 with KC509011
238238247265
8.5 with KC509011
51.5 with KC509011
k1 with KC509011
236238247
GearboxWeight
KC509027LM
-
-
-
14
-
1114
13.5
1114
1414
5 100/112B515 132B535 132B510 100/112B5
3 132B5
35 132B510 100/112B5
45 132B520 100/112B5 -
502A
M2
B3B4S4H3
33
EN Unit 502A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
350NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
3883312792312061761481229984705756
47.639.334.631.728.623.0
3.614.235.016.076.817.969.4511.4314.2116.6220.1024.6124.9829.4135.5840.5044.2349.0060.90
5.55.55.55.55.55.55.5433
2.22.21.51.51.51.11.11.1
0.75
1.21.11.11.21.31.21.11.10.91.11.10.91.01.20.91.00.80.90.8
Ratioscode
ø
Standardø30
ø24ø25ø28ø35
On request
3018301630143012201820162014201220101314131211121310814812614810612610
Output Shaft
01020304050708091011122013141516171819
127148176213239279331293274321286350245288349290316351299
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2300FRFA
46030024004802502600520200
30006001403100620120350070085
3900780704500900405000100015
Feq = FR . 54X+24
FRFAn2 FRFAn2
= =
0.45 LT 0.55 LT 1.00 LT 1.10 LT 1.10 LT 1.15 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
2250450140025005009003000600500
FRFAn1
n2
FA (N)
-R -V-U
80 132100112
Available B14Motor Flanges
-T
90
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
P1R M2R
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132*
-C -D -E
71 80
BBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
112100*
6.36.16.16.36.76.35.74.42.73.32.52.01.51.81.41.1
0.861.0
0.63
150170200250300330354326250354326326250354326295250326250
502A Rating - Aluminium COAXIAL GEARBOXES
132 B5 256.5 297.3 300 259 KC504043 265
With flange 11.7 kgWith feet 11.9 Kg
350NmCoaxial - Gear
209A
A
P502A-F...
P502A-N... Basic Gearbox
Output Flanges
R502A-N... Input Shaft
P502AB1... With feet
20960505
M10x22G
LRS
178
ø30 h6
g6
C m
axS
2 O
H
H1
standard
8
33
b1 f 7
c1
k1
f1
Detail Y
a1
57.5
12
505 8
ø30
h6 27
78
220.3 50
40
M6x16
5M12x20
63
ø24
h6
8
33 60
ø10
171
ø123
69.550°
15.5
178N.5 M10x18
M10x22 65°
s1
e1
d1
2.5
Detail Y
h1
øI
g6
40 43
5.3
5.3
5.3
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
3052/3 110 135÷150 100 190 211.5 18
FeetCode
MarketReference G H R L S H1 O øI S2 only with
motor flangeB5 max.Flange
18203030
19
312/330/3547-57
023-233
06
110130115130
125
160180135135
160
130149.5165135
106
190216170185
205
211.5231.5216.5231.5
226.5
20182425
8
-
15 132B5
-
E2 132202/3 100 135 192 164 201.5 6-
P4 35142 142 130 145 160 243.5 8
30 132B5
L6
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
229.5229.5
256.5
207.3217.3
247
140
200
120 232232
259
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
227.5229.5238.5
227.3247.3272.3
200250
160 230232241
KC0234041KC0234042KC0234043 100/112 B14 238.5 227.3 160 241 KC0854047
x
p1
*Available output shaft
20 132B5
On request
ø 30x60StandardShaft - d1 p1
8 M10x22ø 24x50 8
8
M8x19
M8x19ø 28x60ø 35x60 10 M10x22
h13327
3138
x
ø 25x50 8 M8x1928 1413
15.5
124
g6
KC509028LM
Other feet are available,consult Regal
A see on page bottom
Most popular types
Kit CodeKC509024KC609024KC509022KC509025KC509023
KC509026LM
k1 with KC509011
238238247265
8.5 with KC509011
51.5 with KC509011
k1 with KC509011
236238247
GearboxWeight
KC509027LM
-
-
-
14
-
1114
13.5
1114
1414
5 100/112B515 132B535 132B510 100/112B5
3 132B5
35 132B510 100/112B5
45 132B520 100/112B5 -
502A
M2
B3B4S4H3
34
EN Unit 503A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
350NmCoaxial - Gear
The dynamic efficiency is 0.94 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -D -E -Q -R
63 71 80 90 71 80
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-T
35.229.625.621.118.316.715.113.411.911.110.28.57.86.45.84.84.43.62.9
39.7947.2254.7366.2276.6983.5992.78104.68117.22126.65136.62165.29180.40218.26241.82292.57319.32386.33480.16
1.51.11.10.750.750.550.550.550.370.370.370.250.250.250.250.180.180.120.12
1.01.10.91.01.01.21.01.01.21.11.11.21.20.90.90.90.91.10.7
Ratioscode
ø
Standardø30
ø24ø25ø28ø35
On request
191316191314171314171312131314190814131312101314170812101312913149131271314713129081490812708147081270810
Output Shaft
01020304050607080910111213141516171819
382331384318369297329371278300324264289349387358391305380
Available B5Motor Flanges
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
90
0.75 LT 0.75 LT 1.05 LT 1.15 LT 1.20 LT 1.20 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
BBBBBBBBBBBBBBBBBBB
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2300FRFA
46030024004802502600520200
30006001403100620120350070085
3900780704500900405000100015
Feq = FR . 54X+24
FRFAn2 FRFAn2
= =
2000400140022004409002200440500
FRFAn1
n2
FA (N)
CCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCC
P1R M2R
For all details on lubrication and plugs please consult with a Regaloffice or representative.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
1.51.21.00.770.720.660.550.530.430.400.400.310.310.230.230.170.170.130.08
373354354326354354326354326326354326354326354326354326250
503A Rating - Aluminium COAXIAL GEARBOXES
35
350NmCoaxial - Gear
AP503AB1... With Feet
217.560505
M10x22G
LRS
178
ø30 h6
g6C
max
S2 O
H
H1
standard
8
33
øI
15
*See the table of output shaft for the complete list of diameters
P503A-F... Output Flanges
b1 f 7
c1
k1
f1
Detail Y
a1
57.5
s1
e1
15
With flange 11.9 kgWith feet 12.1 Kg
217.5A
P503A-N... Basic Gearbox R503A-N... Input Shaft
12
505 6
ø30
h6 21.5
78
228.5 35
30
M6x16
2.5M12x20
ø19
h6
8
33 60
ø10
171
ø123
69.550°
15.5
178N.5 M10x18
M10x22 65°
g6
40 43
15
Suggested B14motor flanges
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k171 B1480 B1490 B14
236238238
209.5217227
120140
105 238.5240.5240.5
K0634047K0634046K0634041
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
238236238
227237257
160200
140 240.5238.5240.5
K0634041K0634042K0634043
d1
2.5
Detail Y
h1
x
p1
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22ø 24x50 8
8
M8x19
M8x19ø 28x60ø 35x60 10 M10x22
h13327
3138
x
ø 25x50 8 M8x1928
g6
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
1413
15.5
124
3052/3 110 135÷150 100 190 211.5 18 -
-
FeetCode
MarketReference G H R L S H1 O øI S2 only with
motor flangeB5 max.Flange
18203030
19
312/330/3547-57
023-233
06
110130115130
125
160180135135
160
130149.5165135
106
190216170185
205
211.5231.5216.5231.5
226.5
20182425
8
--
--
- -E2 132202/3 100 135 192 164 201.5 6 -P4 35142 142 130 145 160 243.5 8 -
-
L6
Feet
-
KC509028LM
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC509024KC609024KC509022KC509025KC509023
KC509026LMKC509027LM
k1 with KC509011
244.5246.5246.5
8.5 with KC509011
51.5 with KC509011
k1 with KC509011
246.5244.5246.5
GearboxWeight
63
-
-
-
14
-1414
11
13.5
11
14
14
503A
M2
B3B4S4H3
36
EN Unit 602A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
520NmCoaxial - Gear
The dynamic efficiency is 0.96 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-R -T -V
80 132
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-U
388331279231206176148122100847057
47.639.334.631.728.623.0
3.614.235.016.076.817.969.4511.4314.0016.6220.1024.6129.4135.5840.5044.2349.0060.90
7.57.57.57.57.57.55.55.54443
2.21.851.11.51.11.1
1.11.11.11.01.11.01.21.01.21.21.01.11.11.21.10.91.10.9
Ratioscode
ø
Standardø35
ø28ø30ø38ø40
On request
301830163014301220182016201420121316131413121112814812614810612610
Output Shaft
010203040507080910111220141516171819
171200238288323378331401359426515475418431290433351436
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2800FRFA
56030030006002503200640200
37007401403800760120400084085
42008907058001160406500130015
Feq = FR . 60.5X+25.5
FRFAn2 FRFAn2
= =
0.55 LT 0.85 LT 1.10 LT 1.20 LT 1.20 LT 1.25 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
2250450140025005009003000600500
FRFAn1
n2
FA (N)
11210090
P1R M2R
For all details on lubrication and plugs please consult with a Regaloffice or representative.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132*
-C -D -E
71 80
BBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
112100
* In the P mounting the B5 motor flange can exceed the foot maximum dimensions. Possibly use the flange B14
7.68.07.97.67.97.16.55.54.74.74.03.22.32.21.21.41.21.0
180220260300350370400415435515520520450520320400400400
602A Rating - Aluminium COAXIAL GEARBOXES
132 B5 273.3 333.8 300 275.8 KC504043 281.8
KC609027LMKC609021LM
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC609024KC509022KC609023
KC609029LMKC609025
KC509026LMKC609026LM
With flange 14.1 kgWith feet 14.5 kg
520NmCoaxial - Gear
225.8A
A
P602A-N... Basic Gearbox R602A-N... Input Shaft
P602AB1... With Feet
225.870605
M10x22G
LRS
202
ø35 h6
g6C
max
S2 O
H
H1
standard
10
3812
605
ø35
h6
1038 70
ø10
172.
5
ø123
69.550°
15.5
202N.5 M10x18
M10x22 65°
øI
g6
21.8
21.8
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
Feet
P602A-F... Output Flanges
b1 f 7
c1
k1
f1
Detail Y
a1
67.5
s1
e1
d1
2.5
Detail Y
h1
21.8
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
x
p1
8
27
78
237.3 50
40
M6x16
5M12x20
ø24
h6
40 43
124
Kit CodeB14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
246.3246.3
273.3
243.8253.8
283.8
140
200
120 248.8248.8
275.8
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
244.3246.3255.3
263.8283.8308.8
200250
160 246.8248.8257.8
KC0234041KC0234042KC0234043 100/112 B14 255.3 263.8 160 257.8 KC0854047
*Available output shaft
On request
ø 35x70StandardShaft - d1 p1
10 M10x22ø 28x60 8
10
M8x20
M10x25ø 38x70ø 40x80 12 M12x28
h13831
4143
x
ø 30x60 8 M10x2233
ø106
h8
g6
3562/3 120 170÷185 110 230 223 20 14
-
FeetCode
MarketrReference G H R L S H1 O øI S2 only with
motor flangeB5 max.Flange
35
23.5
024-243
352/3
155
115
170
170
150
130
225
205
258
218
30
8
14
14
H4
B5
20412/3 130 180 149.5 216 233 18 143047-57 115 135 165 170 218 24 13.5
3577 140 170 205 204 243 8 14S7
1906 125 160 106 205 228 8 14L6100/112B5
--
-
-
--
-
19.52302/3 125 170 240 205 228 8 14E340162 162 160 205 200 265 8 14P6
1413
15.5
k1 with KC509011
254.8254.8263.8281.8
8.5 with KC509011
61.5 with KC509011
k1 with KC509011
252.8254.8263.8
GearboxWeight
63
--
-
-
3 132B5
13 132B5
8 132B5
-
13 132B5
602A
M3
B4S4
37
132 B5 273.3 333.8 300 275.8 KC504043 281.8
KC609027LMKC609021LM
Other feet are available,consult Regal.
A see on page bottom
Most popular types
Kit CodeKC609024KC509022KC609023
KC609029LMKC609025
KC509026LMKC609026LM
With flange 14.1 kgWith feet 14.5 kg
520NmCoaxial - Gear
225.8A
A
P602A-N... Basic Gearbox R602A-N... Input Shaft
P602AB1... With Feet
225.870605
M10x22G
LRS
202
ø35 h6
g6C
max
S2 O
H
H1
standard
10
38
12
605
ø35
h6
10
38 70
ø10
172.
5
ø123
69.550°
15.5
202N.5 M10x18
M10x22 65°
øI
g6
21.8
21.8
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
Feet
P602A-F... Output Flanges
b1 f 7
c1
k1
f1
Detail Y
a1
67.5
s1
e1
d1
2.5
Detail Y
h1
21.8
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011KC509012KC509013
x
p1
8
27
78
237.3 50
40
M6x16
5M12x20
ø24
h6
40 43
124
Kit CodeB14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
246.3246.3
273.3
243.8253.8
283.8
140
200
120 248.8248.8
275.8
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
244.3246.3255.3
263.8283.8308.8
200250
160 246.8248.8257.8
KC0234041KC0234042KC0234043 100/112 B14 255.3 263.8 160 257.8 KC0854047
*Available output shaft
On request
ø 35x70StandardShaft - d1 p1
10 M10x22ø 28x60 8
10
M8x20
M10x25ø 38x70ø 40x80 12 M12x28
h13831
4143
x
ø 30x60 8 M10x2233
ø106
h8
g6
3562/3 120 170÷185 110 230 223 20 14
-
FeetCode
MarketrReference G H R L S H1 O øI S2 only with
motor flangeB5 max.Flange
35
23.5
024-243
352/3
155
115
170
170
150
130
225
205
258
218
30
8
14
14
H4
B5
20412/3 130 180 149.5 216 233 18 143047-57 115 135 165 170 218 24 13.5
3577 140 170 205 204 243 8 14S7
1906 125 160 106 205 228 8 14L6100/112B5
--
-
-
--
-
19.52302/3 125 170 240 205 228 8 14E340162 162 160 205 200 265 8 14P6
1413
15.5
k1 with KC509011
254.8254.8263.8281.8
8.5 with KC509011
61.5 with KC509011
k1 with KC509011
252.8254.8263.8
GearboxWeight
63
--
-
-
3 132B5
13 132B5
8 132B5
-
13 132B5
602A
M3
B4S4
38
EN Unit 603A is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
520NmCoaxial - Gear
The dynamic efficiency is 0.94 for all ratios
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
-B -C -D -E -Q -R
63 71 80 90 71 80
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-T
35.229.625.624.521.119.718.317.016.715.113.411.911.110.39.68.98.57.66.86.25.85.04.83.9
39.7947.2254.7357.1366.2271.0176.6982.3083.5992.78104.68117.22126.65135.74145.68157.40165.29185.29205.43224.18241.82278.62292.57363.63
1.51.51.51.51.11.11.10.750.750.750.750.750.550.550.370.370.370.370.370.370.250.250.250.18
1.11.11.00.91.10.91.01.11.11.21.00.91.20.91.31.21.31.00.91.01.11.01.11.0
CCCCCCCCCCCCCCCCCCCCCCCC
Ratioscode
ø
Standardø35
ø28ø30ø38ø40
On request
19131619131417131419131217131219131013131417131019081413131210131417081210131213081417081010131091312
10081491310
10081290814
1008109081290810
Output Shaft
050607080910111213141516171819202122232425262728
382453525548464498538396402446503564449482346373392439487532387446468445
Available B5Motor Flanges
Available B14Motor Flanges
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
QUICK SELECTION Input Speed (n1) = 1400 min-1
90
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2800FRFA
56030030006002503200640200
37007401403800760120400084085
42008907058001160406500130015
Feq = FR . 60.5X+25.5
FRFAn2 FRFAn2
= =
0.75 LT 0.90 LT 1.15 LT 1.25 LT 1.30 LT 1.35 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
2000400140022004409002200440500
FRFAn1
n2
FA (N)
BBBBBBBBBBBBBBBBBBBBBBBB
CCCCCCCCCCCCCCCCCCCCCCCC
For all details on lubrication and plugs please consult with a Regaloffice or representative.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
P1R M2R
1.71.71.51.41.20.961.00.820.820.870.770.690.640.510.470.430.490.370.330.360.280.240.280.19
434515515520520435515435440520515520520440435435520440435520440435520435
603A Rating - Aluminium COAXIAL GEARBOXES
39
With flange 14.3 kgWith feet 14.7 Kg
520NmCoaxial - Gear
234.7A
A
P603A-F...
P603A-N... Basic Gearbox
Output Flanges
R603A-N... Input Shaft
*Available output shaft
P603AB1... With Feet
234.770605
M10x22G
LRS
202
ø35 h6
g6C
max
S2 O
H
H1
standard
10
38
b1 f 7
c1
k1
f1
Detail Y
a1
67.5
12
605
ø35
h6
10
38 70
ø10
172.
5
ø123
69.550°
15.5
202N.5 M10x18
M10x22 65°
s1
e1
d1
2.5
Detail Y
h1
øI
g6
15.5
15.5
15.5
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
6
21.5
78
245.8 35
30
M6x16
2.5M12x20
ø19
h6
40 43
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k171 B1480 B1490 B14
253.2255.2255.2
230237.5247.5
120140
105 255.7257.7257.7
K0634.047K0634046K0634041
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
255.2253.2255.2
247.5257.5277.5
160200
140 257.7255.7257.7
K0634041K0634042K0634043
x
p1
g6 124
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110
130180
200250
130165215
3.53.54
111114
KC509011
KC509013
1413
15.5On request
ø 35x70StandardShaft - d1 p1
10 M10x22ø 28x60 8
10
M8x20
M10x25ø 38x70ø 40x80 12 M12x28
h13831
4143
x
ø 30x60 8 M10x2233
KC609027LMKC609021LM
Other feet are available,consult Regal.
A see on page bottomMost popular types
Kit CodeKC609024KC509022KC609023
KC609029LMKC609025
KC509026LMKC609026LM
Feet
3562/3 120 170÷185 110 230 223 20 14
-
FeetCode
MarketReference G H R L S H1 O øI S2 only with
motor flangeB5 max.Flange
35
23.5
024-243
352/3
155
115
170
170
150
130
225
205
258
218
30
8
14
14
H4
B5
20412/3 130 180 149.5 216 233 18 143047-57 115 135 165 170 218 24 13.5
3577 140 170 205 204 243 8 14S7
1906 125 160 106 205 228 8 14L6-
--
-
-
--
-
19.52302/3 125 170 240 205 228 8 14E340162 162 160 205 200 265 8 14P6
KC509012
k1 with KC509011
261.7263.7263.7
8.5 with KC509011
61.5 with KC509011
k1 with KC509011
263.7261.7263.7
GearboxWeight
63
--
--
-
-
--
-
603A
M3
B4S4
41
HousingRobust cast ironhousing.
FeetRemovable feet.
FlangeFully modular to IECand compactintegrated motor.NEMA C flange.
GearsHardened and ground gears.
Foot prints Compatible to the mainstandard of the market.
Output shaftWith wellproportionedbearings.
A modular and compact product
Large centredistance gears.
Single piece cast ironhousing
With high tensile strength.Precision machined foralignment of bearings
and gearing.
Cast Iron Inline Gearboxes
42
503C703C803C853C903C10031103
Stages3
P -F702C2
501C701C801C851C901C
502C702C802C852C902C10021102
1
Output flange mounted
StagesCast iron coaxial gear boxes
-FYou see feet code in the chart of the dimensions
FeetCode
FeetMarket
Reference G H R L L1 S1818182525
112212/3
1727
42/3
85100759080
110130110110
110÷120
87107.590+2013085
50
L4L5
1316
0405
80100
105125
B..-N
BR
PM
Stage
Modular base
With IEC motor
With male input shaft
With motor flange Without flange / feet
MountingSizeType
On request we can deliver our products according to the ATEX.
Mounted feet
B1B2S1S2M1
HOW TO ORDER
Not available for:701C, 801C,851C, 901C,852C, 902C,1002, 1102,1003, 1103 .
43
503C703C803C853C903C10031103
Stages3
P -F702C2
501C701C801C851C901C
502C702C802C852C902C10021102
1
Output flange mounted
StagesCast iron coaxial gear boxes
-FYou see feet code in the chart of the dimensions
FeetCode
FeetMarket
Reference G H R L L1 S1818182525
112212/3
1727
42/3
85100759080
110130110110
110÷120
87107.590+2013085
50
L4L5
1316
0405
80100
105125
B..-N
BR
PM
Stage
Modular base
With IEC motor
With male input shaft
With motor flange Without flange / feet
MountingSizeType
On request we can deliver our products according to the ATEX.
Mounted feet
B1B2S1S2M1
HOW TO ORDER
Not available for:701C, 801C,851C, 901C,852C, 902C,1002, 1102,1003, 1103 .
ø38ø250
HI
ILM
ø35
ø40
PJ
ø50ø60
4H
D
A
B-F
B
C
STANDARD
B36.57
801C802C 803C
MP
ø40ø50
N Without flange
502C 703C 803C
702C 802C853C 903C
STANDARD
B6
B8
V8
B7
V5
V6
ø
ø
See technical data table
STANDARD
ø30ø35
345
45
ø200ø250
78
ø350ø450
801C802C 803C
56
ø250ø300
ø160ø200
STANDARD501C 502C
503C
701C 702C 703C
851C 852C 853C
501C 502C 503C
701C 702C 703C
501C
ø28(100B5)-4
B3
678
ø300
ø450
901C 902C 903C1002 1003
A ø70 1102 1103
Ratio Output FlangeOutput Shaft Motor Size Terminal BoxPosition
MountingPosition
ø350
PJ
ø50ø60
901C 902C 903C
J ø60
67
ø300ø350
851C852C 853C
1002 1003
1102 1103
HOW TO ORDER
ø
-2 ø19(80B5)ø24(90B5)
ø14(71B5)
-3
-1
øø
-0 ø11(63B5)
-4 ø28
-1 ø14
-2 ø19
ø9(56B5)
-1
-Z503C
503C
ø14(71B5)
852C 902C1003 1103
502C 703C 803C
-3 ø24
702C 802C853C 903C
-3 ø24(90B5)ø28(100B5)
ø19(80B5)
-4
-2
-V=132(ø200)
-T=90(ø140)
-P=63(ø90)
-O=56(ø80)
-R=80(ø120)
-Q=71(ø105)
B14
B5
-F=100÷112(ø250)
-E=90(ø200)
-B=63(ø140)
-A=56(ø120)
-D=80(ø200)
-C=71(ø160)
-U=100÷112(ø160)
-G=132(ø300)
-H=160(ø350)
CA=225(ø450)
-I=180(ø350)
-L=200(ø400)
-6 ø421002 1102
Without flange
Flange
Type R
44
9550P [KW] =M [Nm] n [rpm]
1000P [KW] =M [Kg] g [9.81] v [m / s]
1000P [KW] =F [N] v [m / s]
FR
M
d
FR
d [mm]fK
M [Nm] 2000FR [N] =
n [rpm]M [lb in] =63030 P[HP]
n [rpm]M [Nm] =9550 P[KW]
d [in]fK
M [lb in] 8.9FR [N] =
Rotation
Linear movement
Lifting
— If your application requires higher radial loads, contact our technical office. Higher load may be possible.
REQUIRED POWER
Factor
Output torque
Diameter of driving element
1.15 Gear wheels1.25 Chain sprockets1.75 Narrow v-belt pulley2.50 Flat-belt pulley
- Radial load generated by external transmissions keyed onto input and/or output shafts.
TORQUE
fK
USEFUL FORMULAS
RADIAL LOADS
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
B
A
C
D
B)
C)
B)
Ratioscode
ø
30183016301420182016
Output Shaft
0102030405
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132n2
[min-1]i P1M
[kW]M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
21318515911398
6.577.568.82
12.3914.24
7.57.57.57.55.5
1.21.11.01.01.2
312359419588499
80
-RP1R M2R-G
132
-C -D -E
71 80
BBBBB
Available B5Motor Flanges
90
-F
112100
Type of load and starts per hourOperating hours per day
3 h 10 h 24 h
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75 2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
8.87.97.17.26.4
380390410580600
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
How to select a gearbox
≤ 10
675NmCoaxial - Gear702C Rating - Cast Iron COAXIAL GEARBOXES
45
Ratio
Transmitted Torque Service Factor
NotesOutput Shaft Diameter
Motor flange available
Mounting with reduction ring
Motor flange holes position/terminal box position
Available without reduction bushes
Input Speed
Output Speed Nominal Power
Gear Size Motor Power Nominal Torque Flange Code
B
A
C
D
B)
C)
B)
Ratioscode
ø
30183016301420182016
Output Shaft
0102030405
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132n2
[min-1]i P1M
[kW]M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
21318515911398
6.577.568.8212.3914.24
7.57.57.57.55.5
1.21.11.01.01.2
312359419588499
80
-RP1R M2R-G
132
-C -D -E
71 80
BBBBB
Available B5Motor Flanges
90
-F
112100
Type of load and starts per hourOperating hours per day
3 h 10 h 24 h
Uniform 0.8 1 1.25
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
> 10
Uniform 1 1.25 1.5
Moderate 1.5 1.75
Heavy 1.75 2.15
1.25
1.5
Continuous or intermittentapplication with start / hour
Intermittent applicationwith start / hour
fs
8.87.97.17.26.4
380390410580600
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
How to select a gearbox
≤ 10
675NmCoaxial - Gear702C Rating - Cast Iron COAXIAL GEARBOXES
46
225NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2500FRFA
50030027005402502900580200
32006401403400680120380076085
41008207051001020405500110015
Feq = FR . 56.5X+26.5
FRFAn2 FRFAn2
= =
1.25 LT 0.80 LT 0.80 LT 0.70 LT 1.40 LT 0.80 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
n2
On request reinforced bearings to increase loads.
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
Standardø30
ø35On request
349928105211121811513102
Output Shaft
0102030405
QUICK SELECTION Input Speed (n1) = 1400 min-1
Available B5Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
P1R M2R-T -U
90
-R
80
Available B14Motor Flanges
100112
BBBBB
BBBBB
-E -F
90
-D
80 100112
BBBBB
BBBBB
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
481373263219178
2.913.755.336.397.85
44444
EN Unit 501C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
1.81.61.21.01.1
7698140167205
7.26.44.84.04.3
140160170170225
501C Rating - Cast Iron COAXIAL GEARBOXES
k1 with KC509011
221230
k1 with KC509011
221221230
194.5A
B14 MotorFlanges A Cmax
g6 k180 B1490 B14
215215
260270 140
120 215215
B5 MotorFlanges A Cmax
g6 k180/90 B5
100/112 B5215224
300325
200250
215224
100/112 B14 224 280 160 224
Kit CodeKC0854046KC0854045
Kit CodeKC0234042KC0234043
KC0854047
194.5
54 with KC509011
180 215 4 14 KC50901315.5
GearboxWeight
With flange 20.0 kgWith feet 22.0 kg
225NmCoaxial - Gear
A
P501C-F...
P501C-N... Basic Gearbox
Output Flanges
P501CS4... With feet
60505
M10x22G
LRS
178
ø30 h6
g6
C m
ax
O
HH
1
standard8
33
b1 f 7
c1
k1
f1
Detail Y
a1
60
13
18
d1
Detail Y
h1
øI
g6
85
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
-
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110 130 3.5 11 KC509011
x
p1
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22h133
x14
Kit Code
s1
e1
60
505
M10x22
ø30
h6
g68
33
ø123
9021
7
50°
178
N.5 M10x18
18312/3 110 160 130 190 237 17 1130 115 135 165 170 242 22 13.5- - - - - - - -
47 C50C9024-
C50C9022
- - - - - - - - - -- - - - - - - - - -
ø 35x70 10 M10x2238- - --
200 130 165 3.5 11 KC50901213250
----
65°
only with KC509011
6
-
85
85
100
M12x20
33 105
ø106
h8
70
501C
-
B3S4--
47
k1 with KC509011
221230
k1 with KC509011
221221230
194.5A
B14 MotorFlanges A Cmax
g6 k180 B1490 B14
215215
260270 140
120 215215
B5 MotorFlanges A Cmax
g6 k180/90 B5
100/112 B5215224
300325
200250
215224
100/112 B14 224 280 160 224
Kit CodeKC0854046KC0854045
Kit CodeKC0234042KC0234043
KC0854047
194.5
54 with KC509011
180 215 4 14 KC50901315.5
GearboxWeight
With flange 20.0 kgWith feet 22.0 kg
225NmCoaxial - Gear
A
P501C-F...
P501C-N... Basic Gearbox
Output Flanges
P501CS4... With feet
60505
M10x22G
LRS
178
ø30 h6
g6
C m
ax
O
HH
1
standard8
33
b1 f 7
c1
k1
f1
Detail Y
a1
60
13
18
d1
Detail Y
h1
øI
g6
85*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
-
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110 130 3.5 11 KC509011
x
p1
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22h133
x14
Kit Code
s1
e1
60
505
M10x22
ø30
h6
g68
33
ø123
9021
7
50°
178
N.5 M10x18
18312/3 110 160 130 190 237 17 1130 115 135 165 170 242 22 13.5- - - - - - - -
47 C50C9024-
C50C9022
- - - - - - - - - -- - - - - - - - - -
ø 35x70 10 M10x2238- - --
200 130 165 3.5 11 KC50901213250
----
65°
only with KC509011
6
-85
85
100
M12x20
33 105
ø106
h8
70
501C
-
B3S4--
48
380NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
1.85 LT 1.40 LT 1.40 LT 1.30 LT 2.25 LT 1.60 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
3400FRFA
68030038007602504500900200
4800960140520010401205600112085
650013007073001460409000180015
Feq = FR . 70X+35
FRFAn2 FRFAn2
= =
n2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
tab. 2
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
Standardø35
ø38ø40
On request
29802485189116931495
Output Shaft
0102030405
QUICK SELECTION Input Speed (n1) = 1400 min-1
-G - -
132 -
Available B5Motor Flanges
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-
-P1R
EN Unit 701C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
M2R
-
Notavailable
507395277241206
2.763.545.065.816.79
999
7.57.5
1.61.31.01.21.2
166213304281329
14.411.68.68.58.4
265275290330380
701C Rating - Cast Iron COAXIAL GEARBOXES
49
GearboxWeight
With flange 36.0 kgWith feet 39.5 kg
380NmCoaxial - Gear
270
P701C-F...
P701C-N... Basic Gearbox
Output Flanges
P701CS6... With Feet
70605
M10x22G
LRS
200
ø35 h6
300
max
410
O
H
H1
standard10
38
b1 f 7
c1
270
f1
Detail Y
a1
70
12
22
d1
Detail Y
h1
øI
300
100
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
025/253
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1200 130 165 3.5 11 KC709012
x
p1
*Available output shaft
11
Kit Code
s1
e1
270
70
605
M10x22
ø35
h6
300
10
38
ø140
100
260
90°
200
N.4 M10x19
19.5412/3 130 180 149.5 216 290 25 1430 130 150 195 210 290 25 1435 160 170 175 220 320 30 16
67 KC709024KC709023
KC709022
- - - - - - - - - -- - - - - - - - - -
250 180 215 4 14 KC70901313- - - - - --
-----
100
100
110
M12x19
42 145
ø120
h8
4040
On request
ø 35x70StandardShaft - d1 p1
10 M10x22h138
x
ø 40x80 12 M12x2843ø 38x70 10 M10x2541
701C
-
B4S6H5-
50
670NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
3.20 LT 1.90 LT 1.90 LT 1.55 LT 3.20 LT 2.20 LT AskB3 B6 B7 B8 V5 V6 V8
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
6000FRFA
12003007000140025075001500200
8000160014090001800120
10000200085
110002200701300026004015000300015
Feq = FR . 80.5X+40.5
FRFAn2 FRFAn2
= =
n2
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
Standardø40ø50
On request
181111611314115
Output Shaft
010203
QUICK SELECTION Input Speed (n1) = 1400 min-1
-G - -
132 -
Available B5Motor Flanges
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
227198170
6.177.068.21
999
1.21.41.4
371425494
-
-P1R M2R
EN Unit 801C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
-
Notavailable
10.912.712.2
450600670
801C Rating - Cast Iron COAXIAL GEARBOXES
51
670NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
3.20 LT 1.90 LT 1.90 LT 1.55 LT 3.20 LT 2.20 LT AskB3 B6 B7 B8 V5 V6 V8
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
6000FRFA
12003007000140025075001500200
800016001409000180012010000200085
110002200701300026004015000300015
Feq = FR . 80.5X+40.5
FRFAn2 FRFAn2
= =
n2
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
Standardø40ø50
On request
181111611314115
Output Shaft
010203
QUICK SELECTION Input Speed (n1) = 1400 min-1
-G - -
132 -
Available B5Motor Flanges
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
227198170
6.177.068.21
999
1.21.41.4
371425494
-
-P1R M2R
EN Unit 801C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
-
Notavailable
10.912.712.2
450600670
801C Rating - Cast Iron COAXIAL GEARBOXES
N.4 M12x19
300 230 265 4 14 KC80901416
GearboxWeight
With flange 45.5 kgWith feet 49.5 kg
670NmCoaxial - Gear
278.5
P801C-F...
P801C-N... Basic Gearbox
Output Flanges
P801CS7... With Feet
80705
M12x28G
LRS
246
ø40 h6
300
max
443
.5
O
H
H1
standard12
43
b1 f 7
c1
278.5
f1
Detail Y
a1
80
12
140
M14x22
45
22
d1
Detail Y
h1
øI
300
150
118.
5*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
026/263
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
ø140
h8
x
p1
*Available output shaft
On request
ø 40x80StandardShaft - d1 p1
12 M12x28h143
x
Kit Code
s1
e1
4545
278.5
80
705
M12x28
ø40
h6
300
12
43 118.
5
ø160
120
298.
5
90°
246
25512/3 155 225 156 270 333.5 30 1835 140 170 205 230 318.5 18 17.540 175 215 215 265 353.5 30 16
77 KC809024KC809023
KC809022
- - - - - - - - - -- - - - - - - - - -
ø 50x100 14 M16x3653.5- - --
250 180 215 4 14 KC80901313
- - - - - --
----
118.
5-
801C
-
B5S7H6-
52
5.30 LT 3.60 LT 3.60 LT 2.80 LT 5.80 LT 4.10 LT AskB3 B6 B7 B8 V5 V6 V8
700NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
tab. 2
On request reinforced bearings to increase loads.
9000FRFA
1800300100002000250110002200200
12000240014013000260012014000280085
150003000701600032004020000400015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
n2n2
AGIP Blasia 460
-H - -
160 -
Available B5Motor Flanges
B14Motor Flanges
-
--
-
-
Notavailable
-I
180
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
Standardø50ø60
On request
155113531154
Output Shaft
010203
QUICK SELECTION Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
412343285
3.404.084.91
222222
1.31.21.0
480575693
EN Unit 851C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
P1RM2R
26.425.721.3
600700700
851C Rating - Cast Iron COAXIAL GEARBOXES
53
5.30 LT 3.60 LT 3.60 LT 2.80 LT 5.80 LT 4.10 LT AskB3 B6 B7 B8 V5 V6 V8
700NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
tab. 2
On request reinforced bearings to increase loads.
9000FRFA
1800300100002000250110002200200
12000240014013000260012014000280085
150003000701600032004020000400015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
n2n2
AGIP Blasia 460
-H - -
160 -
Available B5Motor Flanges
B14Motor Flanges
-
--
-
-
Notavailable
-I
180
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
Standardø50ø60
On request
155113531154
Output Shaft
010203
QUICK SELECTION Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
412343285
3.404.084.91
222222
1.31.21.0
480575693
EN Unit 851C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
P1RM2R
26.425.721.3
600700700
851C Rating - Cast Iron COAXIAL GEARBOXESGearboxWeight
22°30'
90°
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
700NmCoaxial - Gear
385.5
P851C-F... Output Flanges
P851CS8... With Foot
100905
M16x36
40 260 215290
220
ø50 h6
350
max
465
.5
30ø1
65 h
8
380
standard14
53.5
b1 f 7
c1
385.5
f1
Detail Y
a1
100
26
31
d1
Detail Y
h1
ø18
350
110.
5*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
x
p1
*Available output shaft
On request
ø 50x100StandardShaft - d1 p1
14 M16x36h1
53.5x
s1
e1
ø190
N.4 M12x18
ø 60x120 18 M20x4264- - -- - - - - - --
110.
5
With flange 90.0 kgWith feet 80.5 kg
180
851C
54
5.90 LT 3.80 LT 3.80 LT 3.50 LT 6.80 LT 4.50 LT AskAGIP Blasia 460
B3 B6 B7 B8 V5 V6 V8
1175NmCoaxial - Gear
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
On request reinforced bearings to increase loads.
tab. 2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
Standardø60
ø50On request
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
23611965156913711173
Output Shaft
0102030405
QUICK SELECTION InputSpeed (n1) = 1400 min-1
-H - -
160 -
Available B5Motor Flanges
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-
-P1R M2R
-
Notavailable
-I
180
528409304256211
2.653.424.605.466.64
2222222222
1.71.61.51.31.3
374483649771937
10350FRFA
2070300115002300250126502530200
13800276014014950299012016100322085
172503450701840036804023000460015
FRFA
EN Unit 901C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2 FRFAn2n2
36.732.830.927.426.5
65075095010001175
901C Rating - Cast Iron COAXIAL GEARBOXES
55
5.90 LT 3.80 LT 3.80 LT 3.50 LT 6.80 LT 4.50 LT AskAGIP Blasia 460
B3 B6 B7 B8 V5 V6 V8
1175NmCoaxial - Gear
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
On request reinforced bearings to increase loads.
tab. 2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
Standardø60
ø50On request
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
The dynamic efficiency is 0.98 for all ratios
Ratioscode
ø
23611965156913711173
Output Shaft
0102030405
QUICK SELECTION InputSpeed (n1) = 1400 min-1
-H - -
160 -
Available B5Motor Flanges
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-
-P1R M2R
-
Notavailable
-I
180
528409304256211
2.653.424.605.466.64
2222222222
1.71.61.51.31.3
374483649771937
10350FRFA
2070300115002300250126502530200
13800276014014950299012016100322085
172503450701840036804023000460015
FRFA
EN Unit 901C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2 FRFAn2n2
36.732.830.927.426.5
650750950
10001175
901C Rating - Cast Iron COAXIAL GEARBOXES
22°30'
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
Gearboxweight
With flange 102 kgWith feet 110.5 kg
1175NmCoaxial - Gear
385.5
P901C-F...
P901C-N... Basic Gearbox
Output Flanges
P901CS8... With Feet
1201105
M20x42G
LRS
281.5
ø60 h6
350
max
540
.5
O
H
H1
standard18
64
b1 f 7
c1
385.5
f1
Detail Y
a1
120
26
31
d1
Detail Y
h1
øI
350
140.
5*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
027/273
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
x
p1
*Available output shaft
On requestø 50x100
StandardShaft - d1 p1
14 M16x36
h1
53.5
x
Kit Code
s1
e1
120
M20x42
ø60
h6
ø190
140
366.
5
22°30'
281.5
N.8 M12x18
702/3
97 KC909026KC909023
KC909027
ø 60x120 18 M20x4264
- - -- 450 350 400 5 18 KC90901622
-
--
140.
5
385.5
1105 350
140.
5
18
64
40 225 250 245 300 452 55 2240 225 250 310 340 452 45 22
25 210 300 165 350 437 30 22
174
M16x26
51 189
ø165
h8
6565
- KC909025-175 215 260 290 402 25 1840
87 KC909024-40 180 215 260 290 407 30 18
22.5°
45°
n°8 holesonly for Kit KC909016
612/3 KC909022-25 195 250 180 300 422 25 18
S8
HS
901C
B7
S9H7
B6
56
320NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2500FRFA
50030027005402502900580200
32006401403400680120380076085
41008207051001020405500110015
Feq = FR . 56.5X+26.5
FRFAn2 FRFAn2
= =
1.25 LT 0.80 LT 0.80 LT 0.70 LT 1.40 LT 0.80 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
1200240140014002809001700340500
FRFAn1
n2
FA (N)
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
Standardø30
ø35On request
2821281828131921172119181718191315181713131815131021131310181013918913718713
Output Shaft
0102030405060708091011121314151617181920
QUICK SELECTION Input Speed (n1) = 1400 min-1
-R -U
80 100112
Available B14Motor Flanges
-T
90
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
71
-Q
CCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCC
P1R M2R
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
16713911492807767635754
47.546.141.738.734.828.326.721.720.216.4
8.3810.0412.3315.1617.5718.1621.0522.3024.7025.8529.4930.3433.6036.2140.2549.4352.5364.5169.3785.19
433
2.22.22.22.22.21.51.51.51.51.11.11.11.10.750.750.370.37
1.01.21.11.21.11.11.11.01.31.31.11.11.01.21.00.91.01.01.11.1
EN Unit 502C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
90 100112
-F-B -C -D
63 71
BBBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
80
-E
215194238215250258299317242253289297240259288354258317168206
4.13.73.22.62.32.42.32.22.01.91.71.61.11.31.10.990.760.750.420.41
225240260260270290320320320320320320250320300320260315190230
502C Rating - Cast Iron COAXIAL GEARBOXES
57
320NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
tab. 2
XFA (N)
FR (N) Feq (N)
2500FRFA
50030027005402502900580200
32006401403400680120380076085
41008207051001020405500110015
Feq = FR . 56.5X+26.5
FRFAn2 FRFAn2
= =
1.25 LT 0.80 LT 0.80 LT 0.70 LT 1.40 LT 0.80 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
1200240140014002809001700340500
FRFAn1
n2
FA (N)
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
Standardø30
ø35On request
2821281828131921172119181718191315181713131815131021131310181013918913718713
Output Shaft
0102030405060708091011121314151617181920
QUICK SELECTION Input Speed (n1) = 1400 min-1
-R -U
80 100112
Available B14Motor Flanges
-T
90
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
71
-Q
CCCCCCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCCCCCC
P1R M2R
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
16713911492807767635754
47.546.141.738.734.828.326.721.720.216.4
8.3810.0412.3315.1617.5718.1621.0522.3024.7025.8529.4930.3433.6036.2140.2549.4352.5364.5169.3785.19
433
2.22.22.22.22.21.51.51.51.51.11.11.11.1
0.750.750.370.37
1.01.21.11.21.11.11.11.01.31.31.11.11.01.21.00.91.01.01.11.1
EN Unit 502C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
90 100112
-F-B -C -D
63 71
BBBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
80
-E
215194238215250258299317242253289297240259288354258317168206
4.13.73.22.62.32.42.32.22.01.91.71.61.11.31.1
0.990.760.750.420.41
225240260260270290320320320320320320250320300320260315190230
502C Rating - Cast Iron COAXIAL GEARBOXES
54 with KC509011
k1 with KC509011
211209211
180 215 4 14 KC50901315.5
GearboxWeight
With flange 15.0 kgWith feet 17.0 kg
320NmCoaxial - Gear
A
P502C-F...
P502C-N... Basic Gearbox
Output Flanges
R502C-N... Input Shaft
P502CS4... With Feet
184.5
60505
M10x22G
LRS
178
ø30 h6
g6
C m
ax
O
HH
1
standard8
33
b1 f 7
c1
k1
f1
Detail Y
a1
60
13
6
21.5
100
195.5 35
30
M6x16
2.5M12x20
33
ø19
h6
18
d1
Detail Y
h1
øI
g6
105
47
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
-
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110 130 3.5 11 KC509011
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k171 B14
90 B14
203
205
214.5
232 140
105 203
205
K0634047
K0634041
Kit CodeB5 MotorFlanges A Cmax
g6 k1
71 B580/90 B5
203205
242262 200
160 203205
K0634042K0634043
100/112 B14 220.3 242 160 220.3 KC404041
x
p1
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22h133
x14
Kit Code
s1
e1
70
A184.5
60
505
M10x22
ø30
h6
g6
8
33
ø123
9021
7
50°
178
N.5 M10x18
18312/3 110 160 130 190 237 17 1130 115 135 165 170 242 22 13.5- - - - - - - -
47 C50C9024-
C50C9022
- - - - - - - - - -- - - - - - - - - -
ø 35x70 10 M10x2238- - --
200 130 165 3.5 11 KC50901213250
----
65°
only with KC509011
6
k1 with KC509011
20963 B5 205 232 140 205 K063404180 B14 205 222 120 205 K0634046 211
211226.3
-47
47
226.3100/112 B5 220.3 287 250 220.3 KC404043
502C
-
B3S4--
58
320NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
1.35 LT 0.80 LT 0.80 LT 0.70 LT 1.50 LT 0.85 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
Ratioscode
ø
Standardø30
ø35On request
19131315131813171315131313131310131891713
1013139131871713913137131861713613187131361313
Output Shaft
01020304050607080910111213141516
CCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCC
-P -Q
63 71
-O
56
Available B14Motor Flanges
The dynamic efficiency is 0.94 for all ratios
QUICK SELECTION Input Speed (n1) = 1400 min-1
-C
71
Available B5Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-B
63
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
2500FRFA
50030027005402502900580200
32006401403400680120380076085
41008207051001020405500110015
Feq = FR . 56.5X+26.5
FRFAn2 FRFAn2
= =
7001401400800160900950190500
FRFAn1
n2
FA (N)
P1R M2R
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
EN Unit 503C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
18.817.016.013.811.410.18.78.27.66.56.25.75.54.84.73.9
74.3382.5687.48101.40122.57138.59160.82170.20183.48214.15225.33244.32254.15289.96300.05356.09
0.370.370.370.370.370.370.250.250.250.180.180.180.180.180.180.12
1.81.61.51.31.11.01.21.21.11.21.21.11.00.90.91.1
176196207240291329257272294262276299311355367282
0.670.600.570.490.410.360.310.290.270.230.220.200.200.170.170.14
320320320320320320320320320320320320320320320320
503C Rating - Cast Iron COAXIAL GEARBOXES
54 with KC509011
180 215 4 14 KC50901315.5
GearboxWeight
With flange 15.0 kgWith feet 17.0 Kg
320NmCoaxial - Gear
A
P503C-F...
P503C-N... Basic Gearbox
Output Flanges
R503C-N... Input Shaft
P503CS4... With Feet
192
60505
M10x22G
LRS
178
ø30 h6
g6
C m
ax
O
HH
1
standard8
33
b1 f 7
c1
k1
f1
Detail Y
a1
60
13
100
202 25
20
M5x13
2.5M12x20
33
ø14
h6
18
d1
Detail Y
h1
øI
g6
105
17
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
-
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110 130 3.5 11 KC509011
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k1
71 B14 208 184.5 105 208 K0504045
Kit CodeB5 MotorFlanges A Cmax
g6 k1
71 B5 208 212 160 208 K0504042
x
p1
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22h133
x14
Kit Code
s1
e1
70
A192
60
505
M10x22
ø30
h6
g6
833
ø123
9021
7
50°
178
N.5 M10x18
- - - - - - - - -- - - - - - - - - -- - - - - - - - - -
- - --200 130 165 3.5 11 KC50901213250
--
65°
only with KC509011
6
63 B5 210.5 202 140 210.5 K0504041
-
17
17
5
16
63 B14 210.5 177 90 210.5 K050404756 B14 208 172 80 208 KC404049
k1 with KC509011
214216.5214
k1 with KC509011
216.5214
18312/3 110 160 130 190 237 17 1130 115 135 165 170 242 22 13.547 C50C9024
C50C9022--
ø 35x70 10 M10x2238
503C
-
B3S4--
59
320NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
1.35 LT 0.80 LT 0.80 LT 0.70 LT 1.50 LT 0.85 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
Ratioscode
ø
Standardø30
ø35On request
191313151318131713151313131313101318917131013139131871713913137131861713613187131361313
Output Shaft
01020304050607080910111213141516
CCCCCCCCCCCCCCCC
CCCCCCCCCCCCCCCC
-P -Q
63 71
-O
56
Available B14Motor Flanges
The dynamic efficiency is 0.94 for all ratios
QUICK SELECTION Input Speed (n1) = 1400 min-1
-C
71
Available B5Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-B
63
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
2500FRFA
50030027005402502900580200
32006401403400680120380076085
41008207051001020405500110015
Feq = FR . 56.5X+26.5
FRFAn2 FRFAn2
= =
7001401400800160900950190500
FRFAn1
n2
FA (N)
P1R M2R
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
EN Unit 503C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
18.817.016.013.811.410.18.78.27.66.56.25.75.54.84.73.9
74.3382.5687.48
101.40122.57138.59160.82170.20183.48214.15225.33244.32254.15289.96300.05356.09
0.370.370.370.370.370.370.250.250.250.180.180.180.180.180.180.12
1.81.61.51.31.11.01.21.21.11.21.21.11.00.90.91.1
176196207240291329257272294262276299311355367282
0.670.600.570.490.410.360.310.290.270.230.220.200.200.170.170.14
320320320320320320320320320320320320320320320320
503C Rating - Cast Iron COAXIAL GEARBOXES
54 with KC509011
180 215 4 14 KC50901315.5
GearboxWeight
With flange 15.0 kgWith feet 17.0 Kg
320NmCoaxial - Gear
A
P503C-F...
P503C-N... Basic Gearbox
Output Flanges
R503C-N... Input Shaft
P503CS4... With Feet
192
60505
M10x22G
LRS
178
ø30 h6
g6
C m
ax
O
HH
1
standard8
33
b1 f 7
c1
k1
f1
Detail Y
a1
60
13
100
202 25
20
M5x13
2.5M12x20
33
ø14
h6
18
d1
Detail Y
h1
øI
g6
105
17
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
-
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1160 110 130 3.5 11 KC509011
ø106
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k1
71 B14 208 184.5 105 208 K0504045
Kit CodeB5 MotorFlanges A Cmax
g6 k1
71 B5 208 212 160 208 K0504042
x
p1
*Available output shaft
On request
ø 30x60StandardShaft - d1 p1
8 M10x22h133
x14
Kit Code
s1
e1
70
A192
60
505
M10x22
ø30
h6
g6
8
33
ø123
9021
7
50°
178
N.5 M10x18
- - - - - - - - -- - - - - - - - - -- - - - - - - - - -
- - --200 130 165 3.5 11 KC50901213250
--
65°
only with KC509011
6
63 B5 210.5 202 140 210.5 K0504041
-17
17
5
16
63 B14 210.5 177 90 210.5 K050404756 B14 208 172 80 208 KC404049
k1 with KC509011
214216.5214
k1 with KC509011
216.5214
18312/3 110 160 130 190 237 17 1130 115 135 165 170 242 22 13.547 C50C9024
C50C9022--
ø 35x70 10 M10x2238
503C
-
B3S4--
60
675NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
2.10 LT 1.40 LT 1.40 LT 1.30 LT 2.25 LT 1.60 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
Standardø35
ø38ø40
On request
301830163014201820161618161613181316131411161114818816814616614
Output Shaft
0102030405060708091011121314151617
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
80
-RP1R M2R
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 70X+35
= =
2000400140022004409002200440500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
3400FRFA
68030038007602504500900200
4800960140520010401205600112085
650013007073001460409000180015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132
-C -D -E
71 80
BBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
112100
2131851591139884736456
47.945.739.136.331.627.122.919.6
6.577.568.8212.3914.2416.7519.2521.7825.0429.2330.6535.7838.5544.3251.7461.0371.25
7.57.57.57.55.55.55.544433
2.22.22.21.11.1
1.21.11.01.01.21.11.01.21.10.91.11.01.11.10.91.11.1
EN Unit 702C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
312358419588499587675558642750592691548630735437510
8.87.97.17.26.46.15.44.74.13.53.42.92.32.32.01.21.2
380390410580600665675675675675675675580665675480560
702C Rating - Cast Iron COAXIAL GEARBOXES
61
675NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
2.10 LT 1.40 LT 1.40 LT 1.30 LT 2.25 LT 1.60 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
Standardø35
ø38ø40
On request
301830163014201820161618161613181316131411161114818816814616614
Output Shaft
0102030405060708091011121314151617
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
80
-RP1R M2R
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 70X+35
= =
2000400140022004409002200440500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
3400FRFA
68030038007602504500900200
4800960140520010401205600112085
650013007073001460409000180015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320 SHELL Omala S4 WE 320
-G
132
-C -D -E
71 80
BBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
112100
2131851591139884736456
47.945.739.136.331.627.122.919.6
6.577.568.82
12.3914.2416.7519.2521.7825.0429.2330.6535.7838.5544.3251.7461.0371.25
7.57.57.57.55.55.55.544433
2.22.22.21.11.1
1.21.11.01.01.21.11.01.21.10.91.11.01.11.10.91.11.1
EN Unit 702C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
312358419588499587675558642750592691548630735437510
8.87.97.17.26.46.15.44.74.13.53.42.92.32.32.01.21.2
380390410580600665675675675675675675580665675480560
702C Rating - Cast Iron COAXIAL GEARBOXESGearboxWeight
With flange 30.0 kgWith feet 33.5 kg
675NmCoaxial - Gear
A
P702C-F...
P702C-N... Basic Gearbox
Output Flanges
R702C-N... Input Shaft
P702CS6... With Feet
229
70605
M10x22G
LRS
200
ø35 h6
g6
C m
ax
O
H
H1
standard10
38
b1 f 7
c1
k1
f1
Detail Y
a1
70
12
8
27
110
241 50
40
M6x16
5M12x19
42
ø24
h6
22
d1
Detail Y
h1
øI
g6
145
50
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
025/253
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1200 130 165 3.5 11 KC709012
ø120
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
249.5249.5
276.5
270280
310
140
200
120 249.5249.5
276.5
KC0854046KC0854045
KC504041
Kit CodeB5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
247.5249.5258.5
290310335
200250
160 247.5249.5258.5
KC0234041KC0234042KC0234043 100/112 B14 258.5 290 160 258.5 KC0854047
x
p1
*Available output shaft
On request
ø 35x70StandardShaft - d1 p1
10 M10x22h138
x11
Kit Code
s1
e1
4040
A229
70
605
M10x22
ø35
h6
g6
10
38
ø140
100
260
90°
200
N.4 M10x19
19.5412/3 130 180 149.5 216 290 25 1430 130 150 195 210 290 25 1435 160 170 175 220 320 30 16
67 KC709024KC709023
KC709022
- - - - - - - - - -- - - - - - - - - -
ø 40x80 12 M12x2843ø 38x70 10 M10x2541 250 180 215 4 14 KC70901313
- - - - - --
-----
50
50
132 B5 276.5 360 300 276.5 KC504043
702C
-
B4S6H5-
62
675NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
2.20 LT 1.40 LT 1.40 LT 1.30 LT 2.40 LT 1.70 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
-R -T
80 90
CCCCCCCCCCCCCCCCCCC
-Q
71
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
Standardø35
ø38ø40
On request
1913181913161713161713141313181313161908161313141908141708141013149131691314
10081610081490816908147081670814
Output Shaft
01020304050607080910111213141516171819
QUICK SELECTION Input Speed (n1) = 1400 min-1
-C -D -E
71 80
BBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
Available B14Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
90
-B
63
CCCCCCCCCCCCCCCCCCC
P1R M2R
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 70X+35
= =
1200240140014002809001700310500
FRFAn1
FA (N)tab. 2
On request reinforced bearings to increase loads.
3400FRFA
68030038007602504500900200
4800960140520010401205600112085
650013007073001460409000180015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320
EN Unit 703C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
SHELL Omala S4 WE 320
22.619.717.014.513.912.111.110.49.58.27.66.85.85.04.33.83.32.92.5
61.8971.1682.4896.29100.51115.56125.96134.91147.05170.44184.15205.87240.34279.22325.97364.41425.43481.19561.76
1.51.51.51.11.10.750.750.750.750.550.550.550.370.370.370.250.250.180.18
1.11.00.91.01.01.21.11.01.01.11.00.91.21.00.91.11.01.11.0
594683792675705556606649707605653730570662773583681589687
1.71.51.31.11.00.910.820.780.720.620.570.510.440.370.320.280.250.220.19
675675675675675675665675675675675675675665675665675665675
703C Rating - Cast Iron COAXIAL GEARBOXESGearboxweight
With flange 30.0 kgWith feet 33.5 kg
675NmCoaxial - Gear
A
P703C-F...
P703C-N... Basic Gearbox
Output Flanges
R703C-N... Input Shaft
P703CS6... With feet
239
70605
M10x22G
LRS
200
ø35 h6
g6
C m
ax
O
H
H1
standard10
38
b1 f 7
c1
k1
f1
Detail Y
a1
70
12
6
21.5
110
250 35
30
M6x16
2.5M12x19
42
ø19
h6
22
d1
Detail Y
h1
øI
g6
145
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
025/253
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1200 130 165 3.5 11 KC709012
ø120
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k1
80 B1490 B14
257.5259.5
224.5232
140
105 257.5259.5
K0634047K0634046
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
259.5257.5259.5
242252272 200
160259.5257.5259.5
K0634041K0634042K0634043 259.5 242 259.5 K0634041
x
p1
*Available output shaft
11
Kit Code
s1
e1
4040
A239
70
605
M10x22
ø35
h6
g6
1038
ø140
100
260
90°
200
N.4 M10x19
19.5412/3 130 180 149.5 216 290 25 1430 130 150 195 210 290 25 1435 160 170 175 220 320 30 16
67 KC709024KC709023
KC709022
- - - - - - - - - -- - - - - - - - - -
250 180 215 4 14 KC70901313- - - - - --
----
140 71 B14120
-
12
12
12
On request
ø 35x70StandardShaft - d1 p1
10 M10x22h138
x
ø 40x80 12 M12x2843ø 38x70 10 M10x2541
703C
-
B4S6H5-
63
675NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
2.20 LT 1.40 LT 1.40 LT 1.30 LT 2.40 LT 1.70 LT AskB3 B6 B7 B8 V5 V6 V8
StandardSupplied
For these mounting position specify in the order or add oil
-R -T
80 90
CCCCCCCCCCCCCCCCCCC
-Q
71
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
Standardø35
ø38ø40
On request
191318191316171316171314131318131316190816131314190814170814101314913169131410081610081490816908147081670814
Output Shaft
01020304050607080910111213141516171819
QUICK SELECTION Input Speed (n1) = 1400 min-1
-C -D -E
71 80
BBBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
Available B14Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
90
-B
63
CCCCCCCCCCCCCCCCCCC
P1R M2R
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 70X+35
= =
1200240140014002809001700310500
FRFAn1
FA (N)tab. 2
On request reinforced bearings to increase loads.
3400FRFA
68030038007602504500900200
4800960140520010401205600112085
650013007073001460409000180015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Telium VSF 320
EN Unit 703C is supplied with synthetic oil for lifetimelubrication, no maintenance is necessary.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axialloads on the gearbox.
SHELL Omala S4 WE 320
22.619.717.014.513.912.111.110.49.58.27.66.85.85.04.33.83.32.92.5
61.8971.1682.4896.29
100.51115.56125.96134.91147.05170.44184.15205.87240.34279.22325.97364.41425.43481.19561.76
1.51.51.51.11.1
0.750.750.750.750.550.550.550.370.370.370.250.250.180.18
1.11.00.91.01.01.21.11.01.01.11.00.91.21.00.91.11.01.11.0
594683792675705556606649707605653730570662773583681589687
1.71.51.31.11.0
0.910.820.780.720.620.570.510.440.370.320.280.250.220.19
675675675675675675665675675675675675675665675665675665675
703C Rating - Cast Iron COAXIAL GEARBOXESGearboxweight
With flange 30.0 kgWith feet 33.5 kg
675NmCoaxial - Gear
A
P703C-F...
P703C-N... Basic Gearbox
Output Flanges
R703C-N... Input Shaft
P703CS6... With feet
239
70605
M10x22G
LRS
200
ø35 h6
g6
C m
ax
O
H
H1
standard10
38
b1 f 7
c1
k1
f1
Detail Y
a1
70
12
6
21.5
110
250 35
30
M6x16
2.5M12x19
42
ø19
h6
22
d1
Detail Y
h1
øI
g6
145
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
025/253
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1200 130 165 3.5 11 KC709012
ø120
h8
Kit CodeB14 MotorFlanges A Cmax
g6 k1
80 B1490 B14
257.5259.5
224.5232
140
105 257.5259.5
K0634047K0634046
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
259.5257.5259.5
242252272 200
160259.5257.5259.5
K0634041K0634042K0634043 259.5 242 259.5 K0634041
x
p1
*Available output shaft
11
Kit Code
s1
e1
4040
A239
70
605
M10x22
ø35
h6
g6
10
38
ø140
100
260
90°
200
N.4 M10x19
19.5412/3 130 180 149.5 216 290 25 1430 130 150 195 210 290 25 1435 160 170 175 220 320 30 16
67 KC709024KC709023
KC709022
- - - - - - - - - -- - - - - - - - - -
250 180 215 4 14 KC70901313- - - - - --
----
140 71 B14120
-
12
12
12
On request
ø 35x70StandardShaft - d1 p1
10 M10x22h138
x
ø 40x80 12 M12x2843ø 38x70 10 M10x2541
703C
-
B4S6H5-
64
900NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
3.20 LT 1.90 LT 1.90 LT 1.55 LT 3.20 LT 2.20 LT AskB3 B6 B7 B8 V5 V6 V8
Standardø40
ø50On request
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
6000FRFA
12003007000140025075001500200
8000160014090001800120
10000200085
110002200701300026004015000300015
Feq = FR . 80.5X+40.5
FRFAn2 FRFAn2
= =
2250450140025005009003000600500
FRFAn1
n2
FA (N)
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
301830163014201820162014161616141316131411161114818816814616614
Output Shaft
0102030405060708091011121314151617
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
1751521319381706051
46.039.637.632.329.826.022.418.916.2
8.029.1810.6815.1117.3020.1323.3927.2130.4235.3837.2443.3147.0253.8562.6374.1686.25
999
7.57.57.55.55.54433
2.22.22.21.11.1
1.11.11.11.11.10.91.10.91.21.01.21.11.11.11.01.11.1
473541630717821955820954780907719836668765890531617
80
-RP1R M2R-G
132
-C -D -E
71 80
BBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
EN Unit 802C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
112100
9.99.89.77.87.86.85.95.14.53.93.73.22.32.32.21.21.2
520590680775885900900900900900895900705810900585680
802C Rating - Cast Iron COAXIAL GEARBOXES
65
900NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
3.20 LT 1.90 LT 1.90 LT 1.55 LT 3.20 LT 2.20 LT AskB3 B6 B7 B8 V5 V6 V8
Standardø40
ø50On request
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
6000FRFA
12003007000140025075001500200
800016001409000180012010000200085
110002200701300026004015000300015
Feq = FR . 80.5X+40.5
FRFAn2 FRFAn2
= =
2250450140025005009003000600500
FRFAn1
n2
FA (N)
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
301830163014201820162014161616141316131411161114818816814616614
Output Shaft
0102030405060708091011121314151617
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
1751521319381706051
46.039.637.632.329.826.022.418.916.2
8.029.18
10.6815.1117.3020.1323.3927.2130.4235.3837.2443.3147.0253.8562.6374.1686.25
999
7.57.57.55.55.54433
2.22.22.21.11.1
1.11.11.11.11.10.91.10.91.21.01.21.11.11.11.01.11.1
473541630717821955820954780907719836668765890531617
80
-RP1R M2R-G
132
-C -D -E
71 80
BBBBBBBBBBBBBBBBB
Available B5Motor Flanges
90
-F
EN Unit 802C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
112100
9.99.89.77.87.86.85.95.14.53.93.73.22.32.32.21.21.2
520590680775885900900900900900895900705810900585680
802C Rating - Cast Iron COAXIAL GEARBOXES
300 230 265 4 14 KC80901416
GearboxWeight
With flange 39.5 kgWith feet 43.5 kg
900NmCoaxial - Gear
A
P802C-F...
P802C-N... Basic Gearbox
Output Flanges
R802C-N... Input Shaft
P802CS7... With Feet
237.5
80705
M12x28G
LRS
246
ø40 h6
g6
C m
ax
O
H
H1
standard12
43
b1 f 7
c1
k1
f1
Detail Y
a1
80
12
8
27
140
249.5 50
40
M6x16
5M14x22
45
ø24
h6
22
d1
Detail Y
h1
øI
g6
150
68.5
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
026/263
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
ø140
h8
B14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
258258
285
303.5313.5
343.5
140
200
120 258258
285
B5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
256258267
323.5343.5368.5
200250
160 256258267 100/112 B14 267 323.5 160 267
x
p1
*Available output shaft
On request
ø 40x80StandardShaft - d1 p1
12 M12x28h143
x
Kit Code
s1
e1
4545
A237.5
80
705
M12x28
ø40
h6
g6
12
43 68.5
ø160
120
298.
5
90°
246
N.4 M12x19
25512/3 155 225 156 270 333.5 30 1835 140 170 205 230 318.5 18 17.540 175 215 215 265 353.5 30 16
77 KC809024KC809023
KC809022
- - - - - - - - - -- - - - - - - - - -
ø 50x100 14 M16x3653.5- - --
250 180 215 4 14 KC80901313
- - - - - --
----
68.5
-
Kit CodeKC0854046KC0854045
KC504041
Kit CodeKC0234041KC0234042KC0234043 KC0854047
132 B5 285 393.5 300 285 KC504043
802C
-
B5S7H6-
66
900NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
3.30 LT 1.90 LT 1.90 LT 1.55 LT 3.40 LT 2.30 LT AskB3 B6 B7 B8 V5 V6 V8
Standardø40
ø50On request
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 80.5X+40.5
= =
FR (N)Input Shaft
2000400140022004409002200440500
FRFAn1
FA (N)tab. 2
On request reinforced bearings to increase loads.
6000FRFA
12003007000140025075001500200
8000160014090001800120
10000200085
110002200701300026004015000300015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
-R -T
80 90
CCCCCCCCCCCCCCCCCC
-Q
71
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
19131819131617131617131415131419081613131419081410131617081410131415081491316
13081471316
1008149081470814
Output Shaft
010203040506070809101112131415161718
QUICK SELECTION Input Speed (n1) = 1400 min-1
-C -D -E
71 80
BBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
Available B14Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
18.516.214.012.010.29.18.67.97.36.86.35.85.64.84.23.52.72.1
75.5086.47100.22116.56136.82153.05163.31178.01191.67206.32222.92242.18250.15289.08330.31394.59514.99680.03
1.51.51.51.11.10.750.750.750.750.750.550.550.550.550.370.370.250.18
1.11.10.91.10.91.11.11.11.00.91.11.01.00.91.11.01.11.1
7258309628179597367858569229927918598881026783936824832
90
-B
63
CCCCCCCCCCCCCCCCCC
EN Unit 803C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
P1R M2R
1.71.61.41.21.00.830.860.790.730.680.630.580.560.490.420.360.270.21
825900900900900810900900900900900900900900890900900900
803C Rating - Cast Iron COAXIAL GEARBOXES
300 230 265 4 14 KC80901416
GearboxWeight
With flange 39.5 kgWith feet 43.5 kg
900NmCoaxial - Gear
A
P803C-F...
P803C-N... Basic Gearbox
Output Flanges
R803C-N... Input Shaft
P803CS7... With Feet
247.5
80705
M12x28G
LRS
246
ø40 h6
g6
C m
ax
O
H
H1
standard12
43
b1 f 7
c1
k1
f1
Detail Y
a1
80
12
6
21.5
140
258.5 35
30
M6x16
2.5M14x22
45
ø19
h6
22
d1
Detail Y
h1
øI
g6
150
30.5
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
026/263
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
ø140
h8
x
p1
*Available output shaft
On request
ø 40x80StandardShaft - d1 p1
12 M12x28h143
x
Kit Code
s1
e1
4545
A247.5
80
705
M12x28
ø40
h6
g6
1243 30
.5
ø160
120
298.
5
90°
246
N.4 M12x19
25512/3 155 225 156 270 333.5 30 1835 140 170 205 230 318.5 18 17.540 175 215 215 265 353.5 30 16
77 KC809024KC809023
KC809022
- - - - - - - - - -- - - - - - - - - -
ø 50x100 14 M16x3653.5- - --
250 180 215 4 14 KC80901313
- - - - - --
----
30.5
Kit CodeB14 MotorFlanges A Cmax
g6 k1
80 B1490 B14
266268
258265.5
140
105 266268
K0634047K0634046
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
268266268
275.5285.5305.5 200
160268266268
K0634041K0634042K0634043 268 275.5 268 K0634041
140 71 B14120
-
803C
-
B5S7H6-
67
900NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
3.30 LT 1.90 LT 1.90 LT 1.55 LT 3.40 LT 2.30 LT AskB3 B6 B7 B8 V5 V6 V8
Standardø40
ø50On request
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 80.5X+40.5
= =
FR (N)Input Shaft
2000400140022004409002200440500
FRFAn1
FA (N)tab. 2
On request reinforced bearings to increase loads.
6000FRFA
12003007000140025075001500200
800016001409000180012010000200085
110002200701300026004015000300015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
-R -T
80 90
CCCCCCCCCCCCCCCCCC
-Q
71
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
19131819131617131617131415131419081613131419081410131617081410131415081491316130814713161008149081470814
Output Shaft
010203040506070809101112131415161718
QUICK SELECTION Input Speed (n1) = 1400 min-1
-C -D -E
71 80
BBBBBBBBBBBBBBBBBB
Available B5Motor Flanges
Available B14Motor Flanges
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
18.516.214.012.010.29.18.67.97.36.86.35.85.64.84.23.52.72.1
75.5086.47
100.22116.56136.82153.05163.31178.01191.67206.32222.92242.18250.15289.08330.31394.59514.99680.03
1.51.51.51.11.1
0.750.750.750.750.750.550.550.550.550.370.370.250.18
1.11.10.91.10.91.11.11.11.00.91.11.01.00.91.11.01.11.1
725830962817959736785856922992791859888
1026783936824832
90
-B
63
CCCCCCCCCCCCCCCCCC
EN Unit 803C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
P1R M2R
1.71.61.41.21.0
0.830.860.790.730.680.630.580.560.490.420.360.270.21
825900900900900810900900900900900900900900890900900900
803C Rating - Cast Iron COAXIAL GEARBOXES
300 230 265 4 14 KC80901416
GearboxWeight
With flange 39.5 kgWith feet 43.5 kg
900NmCoaxial - Gear
A
P803C-F...
P803C-N... Basic Gearbox
Output Flanges
R803C-N... Input Shaft
P803CS7... With Feet
247.5
80705
M12x28G
LRS
246
ø40 h6
g6
C m
ax
O
H
H1
standard12
43
b1 f 7
c1
k1
f1
Detail Y
a1
80
12
6
21.5
140
258.5 35
30
M6x16
2.5M14x22
45
ø19
h6
22
d1
Detail Y
h1
øI
g6
150
30.5
Suggested B14motor flanges
*See the table of output shaft for the complete list of diameters
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
026/263
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
ø140
h8
x
p1
*Available output shaft
On request
ø 40x80StandardShaft - d1 p1
12 M12x28h143
x
Kit Code
s1
e1
4545
A247.5
80
705
M12x28
ø40
h6
g6
12
43 30.5
ø160
120
298.
5
90°
246
N.4 M12x19
25512/3 155 225 156 270 333.5 30 1835 140 170 205 230 318.5 18 17.540 175 215 215 265 353.5 30 16
77 KC809024KC809023
KC809022
- - - - - - - - - -- - - - - - - - - -
ø 50x100 14 M16x3653.5- - --
250 180 215 4 14 KC80901313
- - - - - --
----
30.5
Kit CodeB14 MotorFlanges A Cmax
g6 k1
80 B1490 B14
266268
258265.5
140
105 266268
K0634047K0634046
Kit CodeB5 MotorFlanges A Cmax
g6 k163 B571 B5
80/90 B5
268266268
275.5285.5305.5 200
160268266268
K0634041K0634042K0634043 268 275.5 268 K0634041
140 71 B14120
-
803C
-
B5S7H6-
68
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
Standardø50
ø60On request
3015301330112015201316152011161313151611131311131111813811
Output Shaft
010203040506070809101112131415
QUICK SELECTION Input Speed (n1) = 1400 min-1
- -
-
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
3172642191681401241161049686806554
45.037.4
4.425.306.388.339.9911.2612.0313.5014.6516.2617.5621.5025.8831.0937.43
2222
18.51515151515151511119
7.55.5
BBBBBBBBBBBBBBB
6117337427849401060113212711378153112141486152614751312
-
-
-
Notavailable
P1R M2R
5.40 LT 3.60 LT 3.60 LT 2.80 LT 5.90 LT 4.20 LT AskB3 B6 B7 B8 V5 V6 V8
1600NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
3500700140042008409004500900500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
9000FRFA
1800300100002000250110002200200
12000240014013000260012014000280085
150003000701600032004020000400015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 852C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
-G -H
132
B5Motor Flanges
-I
180
-F
160100112
1.11.01.11.01.01.01.11.11.11.01.21.11.01.01.2
24.220.219.114.713.814.915.215.815.614.113.011.49.47.26.5
7007008008009001100120014001500150015001600160014601600
852C Rating - Cast Iron COAXIAL GEARBOXES
69
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
Standardø50
ø60On request
3015301330112015201316152011161313151611131311131111813811
Output Shaft
010203040506070809101112131415
QUICK SELECTION Input Speed (n1) = 1400 min-1
- -
-
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
3172642191681401241161049686806554
45.037.4
4.425.306.388.339.9911.2612.0313.5014.6516.2617.5621.5025.8831.0937.43
2222
18.51515151515151511119
7.55.5
BBBBBBBBBBBBBBB
611733742784940
1060113212711378153112141486152614751312
-
-
-
Notavailable
P1R M2R
5.40 LT 3.60 LT 3.60 LT 2.80 LT 5.90 LT 4.20 LT AskB3 B6 B7 B8 V5 V6 V8
1600NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
3500700140042008409004500900500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
9000FRFA
1800300100002000250110002200200
12000240014013000260012014000280085
150003000701600032004020000400015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 852C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
-G -H
132
B5Motor Flanges
-I
180
-F
160100112
1.11.01.11.01.01.01.11.11.11.01.21.11.01.01.2
24.220.219.114.713.814.915.215.815.614.113.011.49.47.26.5
7007008008009001100120014001500150015001600160014601600
852C Rating - Cast Iron COAXIAL GEARBOXES
377.5 60
50
M10x25
5
ø28
h6ø165
h8
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
1600NmCoaxial - Gear
A
P852C-F...
P852CS8... Basic Gearbox
Output Flanges
R852CS8... Input Shaft
P852CS8... With Foot
100905
M16x3640
260215290
220
ø50 h6
g6
C m
ax
30
180
380
standard14
53.5
b1 f 7
c1
k1
f1
Detail Y
a1
100
26
8
3131
d1
Detail Y
h1
ø18
g6
35.5
*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
Kit CodeB5 MotorFlanges A Cmax
g6 k1
160/180 B5 402 390.5 350 402
x
p1
*Available output shaft
On request
ø 50x100StandardShaft - d1 p1
14 M16x36h1
53.5x
s1
e1
100
M16x36
ø50
h6
ø190
180
380
220
ø 60x120 18 M20x4264- - -- - - - - - --
35.5
A
905
g6
35.5
14
53.5
100/112 B5 387 340.5 250 387 -
-
Gearboxweight
N.4 M12x18
22°30'
90°
With flange 86.0 kgWith feet 76.5 kg
132 B5 391 365.5 300 391 -
852C
70
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
5.50 LT 3.80 LT 3.80 LT 3.20 LT 7.00 LT 4.60 LT AskB3 B6 B7 B8 V5 V6 V8
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
2250450140025005009003000600500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
9000FRFA
1800300100002000250110002200200
12000240014013000260012014000280085
150003000701600032004020000400015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
-G
132
-C -D -E
71 80
BBBBBBBBBBBBB
90
-F
112100
The dynamic efficiency is 0.94 for all ratios
-T -U
90 100112
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
32.528.927.024.122.220.018.515.412.610.58.77.66.3
43.0348.5251.8158.1763.0970.0575.6591.09111.50133.91161.24184.40222.04
5.55.5444443
2.22.21.51.11.1
1.10.91.21.11.01.00.91.01.21.01.21.11.1
1478166713021462158517601901172315531865154812931557
80
-RRatioscode
ø
Standardø50
ø60On request
20131316131520131116131313131516131113131313131111131181313813116131361311
EN Unit 853C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
01020304050607080910111213
P1R M2R
5.85.04.84.33.84.03.73.12.52.11.71.21.2
1600155016001600155018001800180018001800180014501750
1800NmCoaxial - Gear
Available B5Motor Flanges
QUICK SELECTION Input Speed (n1) = 1400 min-1
Available B14Motor Flanges
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
Output Shaft
853C Rating - Cast Iron COAXIAL GEARBOXES
71
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
5.50 LT 3.80 LT 3.80 LT 3.20 LT 7.00 LT 4.60 LT AskB3 B6 B7 B8 V5 V6 V8
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
2250450140025005009003000600500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
9000FRFA
1800300100002000250110002200200
12000240014013000260012014000280085
150003000701600032004020000400015
FRFAn2 FRFAn2n2
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
-G
132
-C -D -E
71 80
BBBBBBBBBBBBB
90
-F
112100
The dynamic efficiency is 0.94 for all ratios
-T -U
90 100112
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
32.528.927.024.122.220.018.515.412.610.58.77.66.3
43.0348.5251.8158.1763.0970.0575.6591.09111.50133.91161.24184.40222.04
5.55.5444443
2.22.21.51.11.1
1.10.91.21.11.01.00.91.01.21.01.21.11.1
1478166713021462158517601901172315531865154812931557
80
-RRatioscode
ø
Standardø50
ø60On request
20131316131520131116131313131516131113131313131111131181313813116131361311
EN Unit 853C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
01020304050607080910111213
P1R M2R
5.85.04.84.33.84.03.73.12.52.11.71.21.2
1600155016001600155018001800180018001800180014501750
1800NmCoaxial - Gear
Available B5Motor Flanges
QUICK SELECTION Input Speed (n1) = 1400 min-1
Available B14Motor Flanges
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
Output Shaft
853C Rating - Cast Iron COAXIAL GEARBOXES
380
335.5
ø165
h8
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
1800NmCoaxial - Gear
A
P853C-F...
P853CS8... Basic Gearbox
Output Flanges
R853CS8... Input Shaft
P853CS8... With Foot
323.5
100905
M16x3640
260215290
220
ø50 h6
g6
C m
ax
30
180
standard14
53.5
b1 f 7
c1
k1
f1
Detail Y
a1
100
26
8
2731
d1
Detail Y
h1
ø18
g6
85.5
*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
x
p1
*Available output shaft
On request
ø 50x100StandardShaft - d1 p1
14 M16x36h1
53.5x
s1
e1
100
M16x36
ø50
h6
ø190
180
380
220
- - -- - - - - - --
85.5
A323.5
905
g6
85.5
14
53.5
B14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
344
371
325.5335.5
365.5
140
200
120 344
371
B5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
342344353
345.5365.5390.5
200250
160 342344353 100/112 B14 345.5 160
344 344353 353
50
40
M6x16
5
ø24
h6
ø 60x120 18 M20x4264
Kit CodeKC0854046KC0854045
KC504041
Kit CodeKC0234041KC0234042KC0234043 KC0854047
132 B5 371 415.5 300 371 KC504043
GearboxWeight
N.4 M12x18
22°30'
90°
With flange 80.5 kgWith feet 71.0 kg
853C
72
5.90 LT 3.80 LT 3.80 LT 3.40 LT 6.70 LT 4.40 LT AskB3 B6 B7 B8 V5 V6 V8
2100NmCoaxial - Gear
Standardø60
ø50On request
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
3500700140042008409004500900500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
10350FRFA
2070300115002300250126502530200
13800276014014950299012016100322085
172503450701840036804023000460015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
n2n2
AGIP Blasia 460
EN Unit 902C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
30153013301120152013161520111613131516111313111511131111813811
Output Shaft
01020304050607080910111213141516
QUICK SELECTION Input Speed (n1) = 1400 min-1
- -
-
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-
-
-
Notavailable
P1R M2R
23419716212410592867771646058
48.640.033.627.7
5.987.108.6311.2713.3815.2416.2618.0919.8221.9823.5324.2528.8034.9941.6450.60
222222
18.518.518.518.518.515151511119
7.55.5
82798211931310155517711889210218652069221416771991206319761774
1.21.21.11.11.11.11.11.01.11.00.91.21.11.01.01.2
-G -H
132
B5Motor Flanges
-I
180
-F
160100112BBBBBBBBBBBBBBBB
25.525.323.920.319.419.019.717.715.914.613.612.211.19.27.26.3
1000117513501500170019002100210020602100210019402100210019602100
902C Rating - Cast Iron COAXIAL GEARBOXES
73
5.90 LT 3.80 LT 3.80 LT 3.40 LT 6.70 LT 4.40 LT AskB3 B6 B7 B8 V5 V6 V8
2100NmCoaxial - Gear
Standardø60
ø50On request
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
3500700140042008409004500900500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
10350FRFA
2070300115002300250126502530200
13800276014014950299012016100322085
172503450701840036804023000460015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
n2n2
AGIP Blasia 460
EN Unit 902C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
30153013301120152013161520111613131516111313111511131111813811
Output Shaft
01020304050607080910111213141516
QUICK SELECTION Input Speed (n1) = 1400 min-1
- -
-
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
-
-
-
Notavailable
P1R M2R
23419716212410592867771646058
48.640.033.627.7
5.987.108.6311.2713.3815.2416.2618.0919.8221.9823.5324.2528.8034.9941.6450.60
222222
18.518.518.518.518.515151511119
7.55.5
82798211931310155517711889210218652069221416771991206319761774
1.21.21.11.11.11.11.11.01.11.00.91.21.11.01.01.2
-G -H
132
B5Motor Flanges
-I
180
-F
160100112BBBBBBBBBBBBBBBB
25.525.323.920.319.419.019.717.715.914.613.612.211.19.27.26.3
1000117513501500170019002100210020602100210019402100210019602100
902C Rating - Cast Iron COAXIAL GEARBOXES
174
377.5 60
50
M10x25
5M16x26
51
ø28
h6
189
ø165
h8
6565
22°30'
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
GearboxWeight
With flange 98.5 kgWith feet 107.0 kg
2100NmCoaxial - Gear
A
P902C-F...
P902C-N... Basic Gearbox
Output Flanges
R902C-N... Input Shaft
P902CS8... With feet
1201105
M20x42G
LRS
281.5
ø60 h6
g6
C m
ax
O
H
H1
standard18
64
b1 f 7
c1
k1
f1
Detail Y
a1
120
26
8
31
31
d1
Detail Y
h1
øI
g6
65.5
*See the table of output shaft for the complete list of diameters
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
Kit CodeB5 MotorFlanges A Cmax
g6 k1
160/180 B5 402 465.5 350 402
x
p1
*Available output shaft
On request ø 50x100Standard
Shaft - d1 p1
14 M16x36
h1
53.5
x
s1
e1
120
M20x42
ø60
h6
ø190
140
366.
5
22°30'
281.5
N.8 M12x18
ø 60x120 18 M20x4264
- - -- 450 350 400 5 18 KC90901622
65.5
A
1105
g6
65.5
18
64
100/112 B5 387 415.5 250 387 -
-132 B5 391 440.5 300 391 -
22.5°
45°
n° 8 holesonly for Kit KC909016
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
027/273
Kit Code
702/3
97 KC909026KC909023
KC909027-
--40 225 250 245 300 452 55 22
40 225 250 310 340 452 45 22
25 210 300 165 350 437 30 22
- KC909025-175 215 260 290 402 25 1840
87 KC909024-40 180 215 260 290 407 30 18
612/3 KC909022-25 195 250 180 300 422 25 18
S8
HS
B7
S9H7
B6
902C
74
2100NmCoaxial - Gear
Standardø60
ø50On request
6.00 LT 4.10 LT 4.10 LT 3.70 LT 7.30 LT 4.90 LT AskB3 B6 B7 B8 V5 V6 V8
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
2250450140025005009003000600500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
The dynamic efficiency is 0.94 for all ratios
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
80
-RRatioscode
ø
20131520131316131520131116131313131516131113131313131111131181313813116131361311
Output Shaft
0102030405060708091011121314
P1R M2R
28.824.321.320.018.016.414.813.811.49.37.86.45.74.7
48.5557.6465.6470.0477.9385.3694.70101.35123.15150.73179.39217.98247.03300.17
7.55.55.5444433
2.21.51.51.11.1
0.91.10.91.21.11.00.91.10.91.01.21.01.11.0
22571980225517601958214523801917233021001722209317322105
-G
132
-C -D -E
71 80
BBBBBBBBBBBBBB
Available B5Motor Flanges
90
10350FRFA
2070300115002300250126502530200
13800276014014950299012016100322085
172503450701840036804023000460015
FRFAn2
EN Unit 903C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
FRFAn2n2
-F
112100
6.75.75.04.74.23.83.53.22.72.21.81.51.21.1
21002100210021002100210021002100210021002100210019502100
903C Rating - Cast Iron COAXIAL GEARBOXES
75
174
335.5M16x26
51 189
ø165
h8
6565
22°30'
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
GearboxWeight
With flange 86.0 kgWith feet 94.5 Kg
2100NmCoaxial - Gear
A
P903C-F...
P903C-N... Basic Gearbox
Output Flanges
R903C-N... Input Shaft
P903CS8... With feet
323.5
1201105
M20x42G
LRS
281.5
ø60 h6
g6
C m
ax
O
H
H1
standard18
64
b1 f 7
c1
k1
f1
Detail Y
a1
120
26
8
27
31
d1
Detail Y
h1
øI
g6
115.
5
*See the table of output shaft for the complete list of diameters
Feet
With flange and feet only on request.
Ask for compatibility
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
x
p1
*Available output shaft
On request ø 50x100Standard
Shaft - d1 p1
14 M16x36
h1
53.5
x
s1
e1
120
M20x42
ø60
h6
ø190
140
366.
5
22°30'
281.5
N.8 M12x18
- - -- 450 350 400 5 18 KC90901622
115.
5
A323.5
1105 g6
115.
5
18
64
B14 MotorFlanges A Cmax
g6 k180 B1490 B14
132 B14
344
371
400.5410.5
440.5
140
200
120 344
371
B5 MotorFlanges A Cmax
g6 k171 B5
80/90 B5100/112 B5
342344353
420.5440.5465.5
200250
160 342344353 100/112 B14 420.5 160
344 344353 353
50
40
M6x16
5
ø24
h6
ø 60x120 18 M20x4264
Kit CodeKC0854046KC0854045
KC504041
Kit CodeKC0234041KC0234042KC0234043 KC0854047
132 B5 371 490.5 300 371 KC504043
22.5°
45°
n° 8 holesonly for Kit KC909016
FeetCode
MarketReference G H R L S H1 O øI B5 max.
Flange
027/273
Kit Code
702/3
97 KC909026KC909023
KC909027-
--40 225 250 245 300 452 55 22
40 225 250 310 340 452 45 22
25 210 300 165 350 437 30 22
- KC909025-175 215 260 290 402 25 1840
87 KC909024-40 180 215 260 290 407 30 18
612/3 KC909022-25 195 250 180 300 422 25 18
S8
HS
B7
S9H7
B6
903C2100NmCoaxial - Gear
Standardø60
ø50On request
6.00 LT 4.10 LT 4.10 LT 3.70 LT 7.30 LT 4.90 LT AskB3 B6 B7 B8 V5 V6 V8
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 88.5X+38.5
= =
2250450140025005009003000600500
FRFAn1
FA (N)
tab. 2
On request reinforced bearings to increase loads.
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1AGIP Blasia 460
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
The dynamic efficiency is 0.94 for all ratios
QUICK SELECTION Input Speed (n1) = 1400 min-1
-T -U
90 100112
Available B14Motor Flanges
-V
132
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
80
-RRatioscode
ø
20131520131316131520131116131313131516131113131313131111131181313813116131361311
Output Shaft
0102030405060708091011121314
P1R M2R
28.824.321.320.018.016.414.813.811.49.37.86.45.74.7
48.5557.6465.6470.0477.9385.3694.70
101.35123.15150.73179.39217.98247.03300.17
7.55.55.5444433
2.21.51.51.11.1
0.91.10.91.21.11.00.91.10.91.01.21.01.11.0
22571980225517601958214523801917233021001722209317322105
-G
132
-C -D -E
71 80
BBBBBBBBBBBBBB
Available B5Motor Flanges
90
10350FRFA
2070300115002300250126502530200
13800276014014950299012016100322085
172503450701840036804023000460015
FRFAn2
EN Unit 903C is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
FRFAn2n2
-F
112100
6.75.75.04.74.23.83.53.22.72.21.81.51.21.1
21002100210021002100210021002100210021002100210019502100
903C Rating - Cast Iron COAXIAL GEARBOXES
76
Ratiosø
FR (N)Input Shaft
FA (N)
The dynamic efficiency is 0.96 for all ratios
code
Standardø60
391439133911301430133011221422132211161416131414141316111411101410131011
Output Shaft
010203040506070809101112131415161718
QUICK SELECTION Input Speed (n1) = 1400 min-1
- -
-
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
29426922018817214112010990797267625950
45.541.634.0
4.755.216.367.458.159.9611.6912.8015.6317.6519.3320.7722.7523.6027.7830.7633.6941.15
303030303030303022222222
18.518.515151111
8959801197140115351874220024092161244126732872264327432615289623302845
-
-
-
Notavailable
P1R M2R
4.50 LT 8.00 LT 5.50 LT 6.00 LT 10.00 LT 7.50 LT AskB3 B6 B7 B8 V5 V6 V8
2900NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 117X+57
= =
tab. 2
11500FRFA
2300300124002480250134002680200
14900298014015900318012017200344085
183003660702110042204024100482015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1002 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
1.81.81.61.51.41.21.01.01.11.11.11.01.11.11.11.01.21.0
-G -H
132
B5Motor Flanges
-L
200160
-I
180
FRFAn1
5600112014006100122090065001300500
53.051.345.643.139.333.730.127.423.522.522.921.319.518.815.914.413.110.8
165017501900210021002200230023002400260029002900290029002900290029002900
1002 Rating - Cast Iron COAXIAL GEARBOXES
77
Ratiosø
FR (N)Input Shaft
FA (N)
The dynamic efficiency is 0.96 for all ratios
code
Standardø60
391439133911301430133011221422132211161416131414141316111411101410131011
Output Shaft
010203040506070809101112131415161718
QUICK SELECTION Input Speed (n1) = 1400 min-1
- -
-
B14Motor Flanges
-
-
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
29426922018817214112010990797267625950
45.541.634.0
4.755.216.367.458.159.9611.6912.8015.6317.6519.3320.7722.7523.6027.7830.7633.6941.15
303030303030303022222222
18.518.515151111
8959801197140115351874220024092161244126732872264327432615289623302845
-
-
-
Notavailable
P1R M2R
4.50 LT 8.00 LT 5.50 LT 6.00 LT 10.00 LT 7.50 LT AskB3 B6 B7 B8 V5 V6 V8
2900NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 117X+57
= =
tab. 2
11500FRFA
2300300124002480250134002680200
14900298014015900318012017200344085
183003660702110042204024100482015
FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1002 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
1.81.81.61.51.41.21.01.01.11.11.11.01.11.11.11.01.21.0
-G -H
132
B5Motor Flanges
-L
200160
-I
180
FRFAn1
5600112014006100122090065001300500
53.051.345.643.139.333.730.127.423.522.522.921.319.518.815.914.413.110.8
165017501900210021002200230023002400260029002900290029002900290029002900
1002 Rating - Cast Iron COAXIAL GEARBOXES
225 35
4
26
31
120
M20x42
ø60
h6
A
1105
g6
18
64
ø190
225 35
4
412.5
N.8 M12x22
22.5°
45°
471 110
90
M12x28
10
ø42
h6
ø165
h8
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
2900NmCoaxial - Gear
A
P1002-F...
P1002S9... Basic Gearbox
Output Flanges
R1002S9... Input Shaft
P1002S9... With Foot
1201105
M20x42
40310
250330
412.5
ø60 h6
g6
C m
ax
30
standard
b1 f7
c1
k1
f1
Detail Y
a1
120
12
45
d1
Detail Y
h1
ø22
g6
*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
Kit CodeB5 MotorFlanges A Cmax
g6 k1
200 B5 460 425 400 460
x
p1
*Available output shaft
On request
StandardShaft - d1 p1 h1 x
s1
e1
ø 60x120 18 M20x4264
- - --450 350 400 5 18 KC90901622
132 B5 435 375 300 435 KC1109052
KC1109054
160 B5 460 400 350 460 KC1109053
22
18
6422
22.5°
45°
n° 8 holesonly for Kit KC909016
180 B5 460 400 350 460 KC1109053_B
GearboxWeight 120.0 kg
1002
78
Input Shaft
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
Standardø60
301411201414201413161414161413131414161411131413111414111413111411814148141381411
Output Shaft
0102030405060708091011121314
QUICK SELECTION Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
P1R M2R
5.00 LT 9.00 LT 6.50 LT 6.50 LT 11.00 LT 9.00 LT AskB3 B6 B7 B8 V5 V6 V8
3000NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 117X+57
= =
tab. 2
FRFA FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1003 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
-
B14Motor Flanges
-
--
Notavailable
-
-
-G -H
132
B5Motor Flanges
-F
160100112BBBBBBBBBBBBBB
38.827.525.120.318.615.615.214.312.811.79.68.88.16.6
36.1150.8955.7368.8075.3589.4792.0297.99109.52119.94146.47158.37173.45211.82
119
7.57.55.55.55.544433
2.22.2
1.21.01.20.91.21.00.91.21.11.01.11.01.21.0
24472941259131992589307431612462275230142771299624162951
FR (N)FRFAn1
FA (N)3500700140042008409004500900500
115002300300124002480250134002680200
14900298014015900318012017200344085
183003660702110042204024100482015
12.59.28.46.86.25.25.14.84.33.93.23.02.72.2
29003000300030003000300030003000300030003000300030003000
1003 Rating - Cast Iron COAXIAL GEARBOXES
79
Input Shaft
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
Standardø60
301411201414201413161414161413131414161411131413111414111413111411814148141381411
Output Shaft
0102030405060708091011121314
QUICK SELECTION Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
P1R M2R
5.00 LT 9.00 LT 6.50 LT 6.50 LT 11.00 LT 9.00 LT AskB3 B6 B7 B8 V5 V6 V8
3000NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR . 117X+57
= =
tab. 2
FRFA FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1003 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
-
B14Motor Flanges
-
--
Notavailable
-
-
-G -H
132
B5Motor Flanges
-F
160100112BBBBBBBBBBBBBB
38.827.525.120.318.615.615.214.312.811.79.68.88.16.6
36.1150.8955.7368.8075.3589.4792.0297.99
109.52119.94146.47158.37173.45211.82
119
7.57.55.55.55.544433
2.22.2
1.21.01.20.91.21.00.91.21.11.01.11.01.21.0
24472941259131992589307431612462275230142771299624162951
FR (N)FRFAn1
FA (N)3500700140042008409004500900500
115002300300124002480250134002680200
14900298014015900318012017200344085
183003660702110042204024100482015
12.59.28.46.86.25.25.14.84.33.93.23.02.72.2
29003000300030003000300030003000300030003000300030003000
1003 Rating - Cast Iron COAXIAL GEARBOXES
225 35
4
26
31
120
M20x42
ø60
h6
A
1105
g6
18
64
ø190
225 35
4
412.5
N.8 M12x22
22.5°
45°
456.5 60
50
M10x25
5
ø28
h6
ø165
h8
300 230 265 4 14 KC90901421350 250 300 5 18 KC90901521
3000NmCoaxial - Gear
A
P1003-F...
P1003S9... Basic Gearbox
Output Flanges
R1003S9... Input Shaft
P1003S9... With Foot
1201105
M20x42
40310
250330
412.5
ø60 h6
g6
C m
ax
30
standard
b1 f7
c1
k1
f1
Detail Y
a1
120
8
31
d1
Detail Y
h1
ø22
g6
*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
Kit CodeB5 MotorFlanges A Cmax
g6 k1
160 B5 483 400 350 483
x
p1
*Available output shaft
On request
StandardShaft - d1 p1 h1 x
s1
e1
ø 60x120 18 M20x4264
- - --450 350 400 5 18 KC90901622
100/112 B5 468 350 250 468 KC1109056
KC1109058132 B5 468 375 300 468 KC1109057
97
18
6497
22.5°
45°
n° 8 holesonly for Kit KC909016
GearboxWeight 116 kg
1003
80
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
391439133911301430133011221422132211161416131414141316111411101410131011
Output Shaft
010203040506070809101112131415161718
QUICK SELECTION / Selezione veloce Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
29426922018817214112010990797267625950
45.541.634.0
4.755.216.367.458.159.9611.6912.8015.6317.6519.3320.7722.7523.6027.7830.7633.6941.15
4545454545454545453737303030222222
18.5
133314601783208822872792327735894383406844553910428244433842425546604781
P1R M2R
B3 B6 B7 B8 V5 V6 V8
4500NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR .
= =
FRFAn1
FA (N)
tab. 2
FRFA FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1102 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
2.01.91.71.61.51.31.21.11.01.11.01.21.11.01.21.11.00.9
- -
-
B14Motor Flanges
-
--
Notavailable
-G -H
132
B5Motor Flanges
CA
225160
-I
180
-
-
-L
200
Standardø70
6.50 LT 12.50 LT 7.50 LT 8.50 LT 14.50 LT 11.50 LT Ask
130002600300135002700250150003000200
16500330014017500350012019500390085
215004300702500050004029500590015
5600112014006100122090065001300
138X+68
500
86.782.172.067.763.755.249.747.742.038.935.633.130.229.124.722.320.416.7
270028003000330034003600380040004300450045004500450045004500450045004500
1102 Rating - Cast Iron COAXIAL GEARBOXES
A
1401257.5
M20x42
45
ø70 h6
standard
225 B5 KC1109055
250 39
8
29040
g6
ø200
250 39
8
450
N.8 M14x30
22.5°
45°
522 110
90
M12x28
10
ø42
h6
ø170
h8
350 250 300 5 18 KC110901521450 350 400 5 18 KC110901622
4500NmCoaxial - Gear
A
P1102-F...
P1102S0... Basic Gearbox
Output Flanges
R1102S0... Input Shaft
P1102S0... With Foot
M20x42
370 400
450
ø70 h6
g6
C m
ax
b1 f7
c1
k1
f1
Detail Y
a1
140
12
45
d1
Detail Y
h1
ø26
g6
*See the table of output shaft for the complete list of diameters
All flanges arecompatiblewith the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
Kit CodeB5 MotorFlanges A Cmax
g6 k1
x
p1
*Available output shaft
On request
StandardShaft - d1 p1 h1 x
s1
e1
ø 70x140 20 M20x4274.5
- - --- - - - - --
KC1109052
KC1109053_BKC1109053
39
20
74.5
39
537.5 475 450 537.5
180 B5 510.5 425 350 510.5
20
74.5
132 B5 485.5 400 300 485.5160 B5 510.5 425 350 510.5
1257.5
26
31
140
22.5°
45°
Holes n.8 x 45°
Input 225 B5
200 B5 KC1109054510.5 450 400 510.5
GearboxWeight 165 kg
1102
81
The dynamic efficiency is 0.96 for all ratios
Ratioscode
ø
391439133911301430133011221422132211161416131414141316111411101410131011
Output Shaft
010203040506070809101112131415161718
QUICK SELECTION / Selezione veloce Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
29426922018817214112010990797267625950
45.541.634.0
4.755.216.367.458.159.9611.6912.8015.6317.6519.3320.7722.7523.6027.7830.7633.6941.15
4545454545454545453737303030222222
18.5
133314601783208822872792327735894383406844553910428244433842425546604781
P1R M2R
B3 B6 B7 B8 V5 V6 V8
4500NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
Input Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR .
= =
FRFAn1
FA (N)
tab. 2
FRFA FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1102 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
2.01.91.71.61.51.31.21.11.01.11.01.21.11.01.21.11.00.9
- -
-
B14Motor Flanges
-
--
Notavailable
-G -H
132
B5Motor Flanges
CA
225160
-I
180
-
-
-L
200
Standardø70
6.50 LT 12.50 LT 7.50 LT 8.50 LT 14.50 LT 11.50 LT Ask
130002600300135002700250150003000200
16500330014017500350012019500390085
215004300702500050004029500590015
5600112014006100122090065001300
138X+68
500
86.782.172.067.763.755.249.747.742.038.935.633.130.229.124.722.320.416.7
270028003000330034003600380040004300450045004500450045004500450045004500
1102 Rating - Cast Iron COAXIAL GEARBOXES
A
1401257.5
M20x42
45
ø70 h6
standard
225 B5 KC1109055
250 39
8
29040
g6
ø200
250 39
8
450
N.8 M14x30
22.5°
45°
522 110
90
M12x28
10
ø42
h6
ø170
h8
350 250 300 5 18 KC110901521450 350 400 5 18 KC110901622
4500NmCoaxial - Gear
A
P1102-F...
P1102S0... Basic Gearbox
Output Flanges
R1102S0... Input Shaft
P1102S0... With Foot
M20x42
370 400
450
ø70 h6
g6
C m
ax
b1 f7
c1
k1
f1
Detail Y
a1
140
12
45
d1
Detail Y
h1
ø26
g6
*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
Kit CodeB5 MotorFlanges A Cmax
g6 k1
x
p1
*Available output shaft
On request
StandardShaft - d1 p1 h1 x
s1
e1
ø 70x140 20 M20x4274.5
- - --- - - - - --
KC1109052
KC1109053_BKC1109053
39
20
74.5
39
537.5 475 450 537.5
180 B5 510.5 425 350 510.5
20
74.5
132 B5 485.5 400 300 485.5160 B5 510.5 425 350 510.5
1257.5
26
31
140
22.5°
45°
Holes n.8 x 45°
Input 225 B5
200 B5 KC1109054510.5 450 400 510.5
GearboxWeight 165 kg
1102
82
Input Shaft
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
Standardø70
301411201414201413161414161413131414161411131413111414111413111411814148141381411
Output Shaft
0102030405060708091011121314
QUICK SELECTION Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
38.827.525.120.318.615.615.214.312.811.79.68.88.16.6
36.1150.8955.7368.8075.3589.4792.0297.99109.52119.94146.47158.37173.45211.82
18.51511119
7.57.57.55.55.54443
41134694377746624354416042784556376241203681398043594007
P1R M2R
B3 B6 B7 B8 V5 V6 V8
4600NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR .
= =
FA (N)
tab. 2
FRFA FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1103 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
BBBBBBBBBBBBBB
Available B5Motor Flanges
-H -I
180
-F -G
132112100
- -
-
B14Motor Flanges
-
--
Notavailable
-
-160
1.11.01.21.01.11.11.11.01.21.11.21.21.11.1
7.00 LT 13.00 LT 8.00 LT 9.00 LT 16.00 LT 13.50 LT Ask
FRFAn1
3500700140042008409004500900500
138X+68
130002600300135002700250150003000200
16500330014017500350012019500390085
215004300702500050004029500590015
19.414.112.910.49.58.07.67.36.66.04.84.54.13.3
45004600460046004600460045004600460046004500460046004500
1103 Rating - Cast Iron COAXIAL GEARBOXES
83
Input Shaft
The dynamic efficiency is 0.94 for all ratios
Ratioscode
ø
Standardø70
301411201414201413161414161413131414161411131413111414111413111411814148141381411
Output Shaft
0102030405060708091011121314
QUICK SELECTION Input Speed (n1) = 1400 min-1
n2[min-1]
i P1M[kW]
M2M[Nm] f.s. [kW] [Nm]
OutputSpeed Ratio Motor
PowerOutput Torque
Service Factor
NominalPower
NominalTorque
38.827.525.120.318.615.615.214.312.811.79.68.88.16.6
36.1150.8955.7368.8075.3589.4792.0297.99
109.52119.94146.47158.37173.45211.82
18.51511119
7.57.57.55.55.54443
41134694377746624354416042784556376241203681398043594007
P1R M2R
B3 B6 B7 B8 V5 V6 V8
4600NmCoaxial - Gear
Motor Flange Holes PositionMotor Flanges Available Supplied with Reduction Bushing Available on Request without reduction bushingB) C)B)
FR (N)
RADIAL AND AXIAL LOADSOutput Shaft
XFA (N)
FR (N) Feq (N)
Feq = FR .
= =
FA (N)
tab. 2
FRFA FRFAn2 FRFA
For all details on lubrication and plugs please consult with a Regalrepresentative or office.
tab. 1
EN Unit 1103 is supplied without lubricant and equipped witha breather, level and drain plugs. User can add mineraloil keeping existing plugs. Should the user wish to fill itwith synthetic oil, it is recommended to replace theexisting plugs with a closed plug.
See table 1 for lubrication and recommended quantity.In table 2 please see possible radial loads and axial loadson the gearbox.
n2n2
AGIP Blasia 460
BBBBBBBBBBBBBB
Available B5Motor Flanges
-H -I
180
-F -G
132112100
- -
-
B14Motor Flanges
-
--
Notavailable
-
-160
1.11.01.21.01.11.11.11.01.21.11.21.21.11.1
7.00 LT 13.00 LT 8.00 LT 9.00 LT 16.00 LT 13.50 LT Ask
FRFAn1
3500700140042008409004500900500
138X+68
130002600300135002700250150003000200
16500330014017500350012019500390085
215004300702500050004029500590015
19.414.112.910.49.58.07.67.36.66.04.84.54.13.3
45004600460046004600460045004600460046004500460046004500
1103 Rating - Cast Iron COAXIAL GEARBOXES
250 39
8
A
140
M20x42
45
ø70 h6
standard
290g6
ø200450
N.8 M14x30
22.5°
45°
507 60
50
M10x25
5
ø28
h6
ø170
h8
350 250 300 5 18 KC110901521450 350 400 5 18 KC110901622
4600NmCoaxial - Gear
A
P1103-F...
P1103S0... Basic Gearbox
Output Flanges
R1103S0... Input Shaft
P1103S0... With Foot
M20x42
370 400
450
ø70 h6
g6
C m
ax
b1 f7
c1
k1
f1
Detail Y
a1
140
8
31
d1
Detail Y
h1
ø26
g6
*See the table of output shaft for the complete list of diameters
All flanges arecompatible
with the foot
Kit CodeAvailable output flanges
a1 ø b1 c1 e1 f1 s1
x
p1
*Available output shaft
On request
StandardShaft - d1 p1 h1 x
e1
M20x42
- - --- - - - - --
114
114
250 39
8
ø 70x140 20 74.5
20
74.5
Kit CodeB5 MotorFlanges A Cmax
g6 k1
180 B5 533.5 425 350 533.5
100/112 B5 518.5 375 250 518.5 KC1109056
KC1109058_B
132 B5 518.5 400 300 518.5 KC1109057
20
74.5
40
1257.5
s1
1257.5
26
31
140
160 B5 533.5 425 350 533.5 KC1109058
GearboxWeight 156 kg
1103
84
IMPORTANT INFORMATION
Rev. 1.0
Please Read CarefullyThe following WARNING and CAUTION information is supplied to you for your protection and to provide you with many years of trouble free and safe operation of your product.Read ALL instructions prior to operating reducer. Injury to personnel or reducer failure may be caused by improper installation, maintenance or operation.
WARNING:• Written authorisation is required to operate or use reducers in man lift or people moving devices.• Check to make sure that certain applications do not exceed the allowable load capacities, published in the current catalogue.• Buyer shall be solely responsible for determining the adequacy of the product for any and all uses to which Buyer shall apply the product. The application by Buyer shall not be subject to any implied warranty of fitness for a particular purpose.• For safety, Buyer or User should provide protective guards over all shaft extensions and any moving apparatus mounted thereon. The User is responsible for checking all applicable safety codes in his area and providing suitable guards. Failure to do so may result in bodily injury and/or damage to equipment.• Gearboxes operating in a high position should have a protective shield for any possible parts falling down, for casual accidents where people are moving under them.• Hot oil and reducers can cause severe burns. Use extreme care when removing lubrication plugs and vents.• Make certain that the power supply is disconnected before attempting to service or remove any components. Lock out the power supply and tag it to prevent unexpected application power.• Reducers are not to be considered fail safe or self-locking devices. If these features are required, a properly sized, independent holding device should be utilised. Reducers should not be used as a brake.• Any brakes that are used inconjunction with a reducer must be sized or positioned in such a way so as to not subject the reducer to loads beyond the catalogue rating.• Lifting supports, including eyebolts, are to be used for vertically lifting the gearbox only and not other associated attachments or motors.• Use of an oil with an EP additive on units with backstops may prevent proper operation of the backstop. Injury to personnel, damage to the reducer or other equipment may result.• Overhung loads, subject shaft bearings and shafts to stress which may cause premature bearing failure and or shaft breakage from bending fatigue, if not sized properly.
Our company will not be responsible for any direct or indirect damages, caused by wrong use of the products or fornot observing the manuals.
Congratulations and thank you for selecting a Marathon Gearbox. Your new Marathon Gearbox is protected by a 2 year manufacturers warranty, effective from the invoice date of purchase.
Please retain your invoice as proof of purchase.
MALAYSIATorin Industries SND BHD (MALAYSIA) No. 6536A Jalan Bukit KemuningBatu 6 Seksyen 3440470 Shah Alam SelangorT: +60 3 5124 6157F: +60 3 5121 1467SINGAPORECMG Electric Motors (Asia Pacifi c) Pte Ltd12 Tuas Loop 637346SINGAPORET: +65 6863 3473F: +65 6863 3476THAILANDFASCO Motors (Thailand) Limited29/7-8 Bangkruay-Sainoi RoadBangkrangMuang Nonthaburi District Nonthaburi 11000THAILANDT: +66 2447 3300F: +66 2447 3500
Regal Beloit Australia Pty Ltd ABN 61 122 303 084
19 Corporate Ave (PO Box 2340)Rowville VIC 3178, AUSTRALIACustomer Service: 1300 888 853Fax: +61 3 9237 4010
www.regalaustralia.com.au
VICTORIA / HEAD OFFICE19 Corporate AvenueRowville VIC 3178T: 1300 888 853F: +61 3 9237 4050NEW SOUTH WALES6-7 Bushells PlaceWetherill Park NSW 2164T: 1300 888 853F: +61 2 8781 3131QUEENSLAND7 Mahogany CourtWillawong QLD 4110T: 1300 888 853F: +61 7 3246 3210CAIRNS (Service • Repairs • Sales)2/159-161 Newell StreetBungalow QLD 4870T: 1300 888 853F: +61 7 4033 5553MACKAYShed 5/58 Elvin StreetPaget QLD 4740T: 1300 888 853F: +61 7 4952 6277SOUTH AUSTRALIA47 Research RoadPooraka SA 5095T: 1300 888 853F: +61 8 8359 5675WESTERN AUSTRALIA21 Colin Jamieson DriveWelshpool WA 6106T: 1300 888 853F: +61 8 6253 3710
NEW ZEALANDAUCKLANDRegal Beloit New Zealand Ltd18 Jomac PlaceAvondaleT: 0800 676 722F: +64 9820 8504ROTORUA51 Purura StreetRotoruaT: 0800 676 722F: +64 7347 8629
APPLICATION CONSIDERATIONS
The proper selection and application of power transmission products and components, including the related area of product safety, is the responsibility of the customer. Operating and performance requirements and potential associated issues will vary appreciably depending upon the use and application of such products and components. The scope of the technical and application information included in this publication is necessarily limited. Unusual operating environments and conditions, lubrication requirements, loading supports, and other factors can materially affect the application and operating results of the products and components and the customer should carefully review its requirements. Any technical advice or review furnished by Regal Beloit Australia Pty Ltd and its affi liates with respect to the use of products and components is given in good faith and without charge, and Regal assumes no obligation or liability for the advice given, or results obtained, all such advice and review being given and accepted at customer’s risk.
For a copy of our Standard Terms and Conditions of Sale, Disclaimers of Warranty and Limitation of Liability, please contact Customer Service at 1300 888 853 or visit www.regalaustralia.com.au. These terms and conditions of sale, disclaimers and limitations of liability apply to any person who may buy, acquire or use a Regal Beloit Australia Pty Ltd product referred to herein, including any person who buys from a licensed distributor of these branded products.
Marathon Gearboxes and Regal are trademarks of Regal Beloit Australia Pty Ltd or one of its affiliated companies.
©2016, 2016 Regal Beloit Australia Pty Ltd, All Rights Reserved. MCC16019E • Form# xxxxE • Created in AU