M001 MECHANICAL SCHEDULES & GENcochisetech.net/wp-content/uploads/2016/11/90-Mechanical.pdfb. test...
4
MECHANICAL SCHEDULES & GENERAL NOTES DO NOT SCALE DRAWING M001 THIS DRAWING IS CLASSIFIED AS PART OF AN UNPUBLISHED COLLECTION OF VISUAL ART. UNDER THE 1978 COPYRIGHT ACT, IT IS AN EXCLUSIVE ORIGINAL WORK OF AUTHORSHIP. NONE OF THE PICTORIAL, GRAPHIC OR TECHNICAL CHARTS OR DRAWINGS DEPICTED ON THIS SHEET MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS WITHOUT THE EXPRESS PRIOR WRITTEN PERMISSION OF THE ARCHITECT. THIS PLAN IS PRODUCED ONLY FOR THIS PROJECT ON THIS SITE AND MAY NOT BE USED AT OTHER LOCATIONS. SHEET TITLE: ORIGINAL ISSUE: Preliminary SEAL: REV DATE DESCRIPTION SHEET NUMBER: PROJECT: AC489 PROJECT: BAPTIST CHURCH SIERRA VISTA, AZ VILLAGE MEADOWS DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION MM-DD-YY MM-DD-YY MM-DD-YY MM-DD-YY MM-DD-YY MM-DD-YY 4 1 2 3 5 6 DESCRIPTION ORIGINAL ISSUE Preliminary 0 DANIEL COOK ARCHITECT│2909 WASHINGTON BLVD - OGDEN, UT 84401│PH: 800-552-7137│www.BGWSERVICES.com SIERRA VISTA, ARIZONA 85635 1407 S EL CAMINO REAL PRELIMINARY DRAWING! NOT FOR CONSTRUCTION! T H C TITLE SECTION SHEET # MECH ROOF PLAN DETAIL # SHEET # 1 EQUIPMENT CALLOUT SCOPE OF WORK FOR LENNOX PROVIDED EOC, AND MECHANICAL CONTRACTOR CONTROL INSTALLATION AND MECHANICAL CONTRACTOR CONTRACTED INDEPENDENT TEST AND BALANCE. A. EQUIPMENT OPERATIONS CHECK (EOC) (LENNOX PROVIDED) THROUGH BGWS • TEST ALL LENNOX EQUIPMENT BASED ON THE STANDARD LENNOX EOC REPORT. • CONTACT LENNOX SUPPORT WITH ANY EQUIPMENT DEFICIENCIES AND COORDINATE REPAIR OR REPLACEMENT AS NECESSARY TO ASSIST IN PROVIDING OPERATIONAL EQUIPMENT PRIOR TO OPENING DATE. • DISTRIBUTE COPIES OF EOC REPORT AS REQUESTED BY LENNOX. B. TEST AND BALANCE (TAB) (MECHANICAL CONTRACTOR CONTRACTED) • UPON ARRIVAL TO THE SITE, INSPECT MECHANICAL SYSTEM AND NOTE ANY DEFICIENCIES THAT COULD PREVENT PROPER OPERATION AND/OR BALANCING OF THE MECHANICAL SYSTEM TO THE OWNER, GENERAL CONTRACTOR AND MECHANICAL CONTRACTOR. • INSPECT ALL MECHANICAL EQUIPMENT FOR PROPER INSTALLATION PER MEP DESIGN. • TEST ALL MECHANICAL EQUIPMENT PER NEBB STANDARDS FOR AIR BALANCE FOR PROPER OPERATION. • THE BALANCING OF THE MECHANICAL SYSTEM WILL BE PERFORMED TO MEET NEBB STANDARDS UNLESS SPECIFICALLY REQUESTED OTHERWISE, IN WRITING, BY OWNER OR OWNERS ENGINEERING FIRM. • BALANCE ALL RTU’S, GRILLS, REGISTERS AND EXHAUST FANS PER MECHANICAL DESIGN AS NOTED ON MEP DRAWINGS PER NEBB STANDARDS FOR AIR BALANCE. • GENERATE A FIELD REPORT OF ANY OUTSTANDING MECHANICAL DEFICIENCIES, IF ANY, THAT COULD NOT BE RESOLVED DURING THE TAB VISIT AND DISTRIBUTE A COPY TO THE OWNER, GENERAL CONTRACTOR AND MECHANICAL CONTRACTOR AND NOTE IF A RE-VISIT WILL BE REQUIRED. • GENERATE A COMPLETE TAB REPORT AND SUBMIT TO THE OWNER AND AS DIRECTED WITHIN ONE (1) WEEK OF THE COMPLETION OF THE AIR BALANCE. C. CONTROL INSTALLATION (BGW SUPPLY CONTRACTED CONTROL CONTRACTOR) • PROVIDE CONTROL INSTALLATION DRAWINGS SHOWING CABLE RUNS AND LOCATIONS. • PROVIDE AND TERMINATE PLENUM CABLE FOR LENNOX PROVIDED THEROMOSTATS, HUMIDITY SENSORS AND CO2 SENSORS CONDUIT IN SPACE. • PROVIDE, PLENUM COMMUNICATION CABLE BETWEEN RTUS INSTALLED BY ELECTRICAL CONTRACTOR. • PROVIDE, AND TERMINATE PLENUM CABLE FOR LENNOX PROVIDED SPACE SENSORS AND HUMIDITY SENSORS CONDUIT IN SPACE, IF REQUIRED. WIRE INSTALLATION BY ELECTRICAL CONTRACTOR. • PROGRAM AND COMMISSION CONTROLS AS REQUIRED TO MEET OWNER SPECIFICATIONS. • PROVIDE REPORT DETAILING COMMISSION OF CONTROLS AND SUBMIT TO OWNER. • PROVIDE OWNER OPERATORS 2 HOURS OF TRAINING. D. WARRANTY • LENNOX PROVIDES A ONE (1) YEAR PARTS WARRANTY ON THE WORKMANSHIP OF ALL LENNOX PROVIDED MATERIAL, AND EQUIPMENT, STARTING AT CERTIFICATE OF OCCUPANCY. E. CLARIFICATIONS AND RESPONSIBILITY OF MECHANICAL & ELECTRICAL CONTRACTOR • CONDUIT, RACEWAYS SHALL BE FURNISHED AND INSTALLED BY THE ELECTRICAL CONTRACTOR. CONTROL CONTRACTOR WILL REQUIRE A CONDUIT, AND WIRE RACEWAY PATH FOR THE SPACE SENSORS IN AREAS NOT ACCESSIBLE, SUCH AS WALLS, SANCTUARY AND GYMNASIUM AREAS, SUCH THAT ELECTRICAL CONTRACTOR CAN INSTALL CONTROL WIRE AND SPACE SENSORS. • CABLE (PROVIDED BY THE CONTROL CONTRACTOR) SHALL BE PULLED OR INSTALLED AT EACH LOCATION SHOWN ON THE CONTROL DRAWINGS. (INSTALLED BY ELECTRICAL CONTRACTOR) • ELECTRICAL CONTRACTOR SHALL INSTALL ALL SENSORS AND PANEL. • THE EOC, TAB, AND CONTROL INSTALLATION SCOPE WILL BE COORDINATED WITH THE GENERAL AND/OR MECHANICAL CONTRACTOR. • THE GENERAL OR MECHANICAL CONTRACTOR WILL NOTIFY LENNOX WITH AT LEAST FOURTEEN (14) DAYS ADVANCED NOTICE THAT THE HVAC SYSTEM IS 100% COMPLETE AND READY FOR EOC AND CONTROL TERMINATION. O HIGH VOLTAGE MUST BE CONNECTED TO EACH UNIT O GAS MUST BE CONNECTED TO EACH UNIT O PROPER PHASE ROTATION MUST BE CONFIRMED AT THE DISCONNECT O ALL STAGES OF HEATING AND COOLING MUST BE CONFIRMED OPERATIONAL O UNITS CAN BE PUT IN STANDALONE OPERATION BY SETTING THE UNIT OPERATION TO L CONNECTION/RETURN AIR BACK UP MODE. CONSULT THE M-2 PRODIGY CONTROL MANUAL FOR INSTRUCTIONS OR CONTACT LENNOX NATIONAL ACCOUNT TECHNICAL SUPPORT 1-800-367-6285 FOR ASSISTANCE. • THE MECHANICAL CONTRACTOR WILL PROVIDE A REPRESENTATIVE ON-SITE DURING THE EOC SERVICE TO ADDRESS DEFICIENCIES FOUND. LENNOX WILL MAKE ALL REASONABLE ATTEMPTS TO RESOLVE DEFICIENCIES, IF ANY, WITH THE MECHANICAL CONTRACTOR WHILE ONSITE. F. WORKING HOURS • WORKING HOURS SHALL FOLLOW CONSTRUCTIONS HOURS OR AS REQUESTED BY THE GENERAL CONTRACTOR 1 1 RTU 1 1 1 1 1 MECHANICAL GENERAL NOTES MECHANICAL LEGEND DROP RISE DROP 20x10 16''Ø RISE DROP RISE 16''Ø FSD 16x10 FD SD E-1 CFM D-1 CFM D-1 CFM 20x10 20x10 20x10 14''Ø 12x10 12x10 D-1 CFM D-1 CFM 16''Ø 6''Ø EXHAUST AIR REGISTER - SQUARE SUPPLY DIFFUSER - SQUARE FIRE/SMOKE DAMPER SMOKE DAMPER LINEAR DIFFUSERS - SIDE MOUNT FLEXIBLE DUCT FIRE DAMPER MANUAL BALANCING DAMPER SLOPED DUCT DROP SLOPED DUCT RISE FLAT OVAL DUCT DUCT - RISE UNDER FLOOR ROUND DUCT POSITIVE PRESSURE DUCT - DROP ROUND DUCT RECTANGULAR DUCT ROUND DUCT - DROP ROUND DUCT - RISE SOUND ATTENUATOR ROUND TO ROUND TRANSITION RECTANGULAR TRANSITION - OFFSET RECTANGULAR TO ROUND TRANSITION RECTANGULAR TRANSITION LINEAR DIFFUSER - BOTTOM MOUNT SUPPLY DIFFUSER - ROUND SECTION CALLOUT DETAIL CALLOUT THERMOSTAT OR TEMPERATURE SENSOR HUMIDISTAT CARBON DIOXIDE DETECTOR POINT OF CONNECTION POINT OF DEMOLITION REVISION DELTA KEYED NOTE CALLOUT M301 1 SCALE: 1/8" = 1' - 0" M501 1 R-1 CFM RETURN AIR REGISTER - SQUARE 92ºF Db SUMMER HVAC DESIGN DATA OUTSIDE DESIGN TEMPS.: 64ºF Wb SUMMER 17ºF Db WINTER DESIGN ALTITUDE: 175 FT. INTERIOR DESIGN DATA ALL SUMMER WINTER Db 75º %HUMIDITY 50% 72º 40% Db %HUMIDITY NOTE: ALL ROUND DUCTWORK, FITTINGS AND VOLUME CONTROL DAMPERS ARE TO BE SPIROSAFE GASKETED DUCT MANUFACTURED BY LINDAB. BGW HAS A NATIONAL ACCOUNT AGREEMENT WITH LINDAB INC. FOR THIS PROJECT CONTACT LINDAB TAKE OFF DEPARTMENT AT (757) 488-7234 EXT. 381 FOR SPIRAL DUCT QUOTATION. THE DRAWINGS INDICATE DIAGRAMMATICALLY THE EXTENT OF THE WORK. DUE TO THE SCALE OF THE DRAWINGS, OFFSET, FITTINGS, AND ACCESSORIES MAY NOT BE INDICATED. WORK INDICATED, BUT HAVING DETAILS OMITTED, SHALL BE COMPLETELY PROVIDED BY CONTRACTOR TO PERFORM FUNCTION INTENDED AT NO ADDITIONAL COST. CONTRACTOR SHALL EXAMINE THE ARCHITECTURAL, STRUCTURAL, PLUMBING, MECHANICAL, AND ELECTRICAL DRAWINGS AND SPECIFICATIONS TO AVOID CONFLICT WITH OTHER TRADES. MINOR VARIATIONS IN LOCATION OF EQUIPMENT SHALL BE MADE ON WRITTEN APPROVAL OF THE ENGINEER AT NO ADDITIONAL COST. MECHANICAL CONTRACTOR IS RESPONSIBLE FOR PAYMENT, ORDERING, DELIVERY COORDINATION RECEIVING AND INSTALLATION OF ALL THE LINDAB SUPPLIED MATERIAL. THE CONTRACTOR IS REQUIRED TO REVIEW THE MECHANICAL DRAWINGS, MAKING ANY NECESSARY MODIFICATIONS TO ACCOUNT FOR FIELD VARIANCES AND SEND THESE FINAL DRAWINGS TO LINDAB FOR A DUCT QUOTATION. THESE REVISED PLANS ARE TO BE E-MAILED 72 HOURS BEFORE BID TIME TO LINDAB TAKE OFF FOR A PRODUCT QUOTATION. THE CONTRACTOR MUST APPROVE THE FINAL DUCT DRAWINGS AND BILL OF MATERIAL BEFORE PLACING THE ORDER WITH LINDAB. NOTE: MECHANICAL CONTRACTOR TO REVIEW ALL DRAWINGS FOR CONFLICTS WITH STRUCTURE AND OTHER TRADES. MECHANICAL CONTRACTOR TO RESOLVE ALL CONFLICTS WITH ENGINEER PRIOR TO ORDERING, FABRICATING OR INSTALLING DUCTWORK. NOTE: 1) SPACE ABOVE CEILING IS TO BE USED AS A RETURN AIR PLENUM. ALL MATERIALS TO BE PLENUM RATED. 2) ALL TERMINAL SUPPLY DUCT BRANCHES TO BE EQUIPPED WITH MANUAL BALANCING DAMPER. 3) FLEX DUCT (MAXIMUM 60" LONG) TYPICAL ON EACH DIFFUSER EXCEPT IN EXPOSED APPLICATIONS. 4) PROVIDE TURNING VANES IN ALL RECTANGULAR ELBOWS. EF-1 SYMBOL GREENHECK G-123-B ROOF CFM ARRANGEMENT, ROTATION & DISCHARGE DOWNBLAST 825 EXHAUST FAN SCHEDULE 0.35 12" SPECIFICATION SECTION 233423 HEIGHT ABOVE ROOF (INCHES) SP "WG TYPE MANUFACTURER AND MODEL NO. OPERATING WEIGHT (LBS.) ACCESSORIES AND REMARKS 995 RPM FAN DETAIL NO. RPM MOTOR 1140 H.P. ELECTRICAL VOLT/Ø/Hz. 76 CONTROL METHOD 1/6 EF-2 EF-3 150 0.35 12" 1323 1550 47 1/20 EF-4 GREENHECK G-080-D WALL SWITCH EF-5 5 0.3 929 1140 66 1/6 GREENHECK G-097-B EF-6 EF-7 EF-8 120/1/60 BACKDRAFT DAMPER GREENHECK G-123-B 750 0.35 12" WALL SWITCH 958 1140 76 1/6 BACKDRAFT DAMPER BACKDRAFT DAMPER BACKDRAFT DAMPER BACKDRAFT DAMPER WALL SWITCH WALL SWITCH 12" BACKDRAFT DAMPER WALL SWITCH BACKDRAFT DAMPER WALL SWITCH BACKDRAFT DAMPER WALL SWITCH EF-9 BACKDRAFT DAMPER 24" x 24" OVERALL SIZE DIFFUSER AND GRILLE SCHEDULE D-1 SYMBOL TITUS TMS MIN./MAX. CFM 0/100 4-WAY BLOW 6"Ø NECK SIZE SUPPLY AIR TYPE ACCESSORIES AND REMARKS LAY-IN D-2 TITUS TMS 100/240 8"Ø D-3 TITUS TMS 240/400 10"Ø 24" x 24" 4-WAY SUPPLY AIR 24" x 24" 4-WAY SUPPLY AIR LAY-IN LAY-IN SPECIFICATION SECTION 233713 MANUFACTURER AND MODEL NO. D-4 TITUS TMS 400/520 12"Ø 24" x 24" 4-WAY SUPPLY AIR LAY-IN D-7 250/425 360º SUPPLY AIR NECK MOUNT D-8 375/600 360º SUPPLY AIR NECK MOUNT 24" x 24" E-1 0/130 4-WAY 6"Ø LAY-IN E-2 130/260 8"Ø E-3 260/400 10"Ø 24" x 24" 4-WAY 24" x 24" 4-WAY LAY-IN LAY-IN 24" x 24" D-5 TITUS 300FL 0/130 4-WAY SUPPLY AIR D-6 24" x 24" R-1 TITUS PXP 500/1100 N/A RETURN AIR LAY-IN R-2 TITUS PXP 0/500 24" x 12" LAY-IN RETURN AIR N/A N/A N/A EXHAUST AIR EXHAUST AIR EXHAUST AIR 120/1/60 120/1/60 120/1/60 1. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT NECESSARY TO CONSTRUCT A COMPLETE, OPERATIONAL HVAC SYSTEM FOR THE ENTIRE PROJECT AS SHOWN ON THESE DRAWINGS, INCLUDING ALL NECESSARY FEES AND PERMITS. 2. THE ENTIRE INSTALLATION SHALL CONFORM TO THE MOST RECENTLY ADOPTED REQUIREMENTS OF THE INTERNATIONAL MECHANICAL CODE, INTERNATIONAL PLUMBING CODE, INTERNATIONAL BUILDING CODE, AND ALL OTHER APPLICABLE CITY, COUNTY, AND STATE CODES AND REGULATIONS IN EFFECT AT THE DATE OF THE PERMITTING. 3. COORDINATE THE INSTALLATION OF ALL HVAC PIPING, DUCTWORK, AND EQUIPMENT WITH PLUMBING PIPING, PLUMBING EQUIPMENT, FIRE PROTECTION PIPING AND ALL OTHER TRADES INCLUDING BUT NOT LIMITED TO: THE MECHANICAL CONTRACTOR, ELECTRICAL CONTRACTOR, FIRE PROTECTION CONTRACTOR, GENERAL CONTRACTOR, AND ANY CONTRACTOR HIRED DIRECTLY BY THE OWNER PRIOR TO FABRICATION AND INSTALLATION. WHERE CONFLICTS MAY OCCUR, THEY SHALL BE RESOLVED PRIOR TO INSTALLATION. 4. THE DRAWINGS SHOW THE GENERAL DESIGN, ARRANGEMENTS AND THE EXTENT OF THE SYSTEM. IT SHALL BE THE WORK OF THE CONTRACTOR TO MAKE SUCH SLIGHT ALTERATIONS AS MAY BE NECESSARY TO MAKE THE SYSTEM COMPLETE AND OPERATIONAL IN ACCORDANCE WITH THE DESIGN INTENT. MAJOR DEVIATIONS SUCH AS CHANGES IN COMPONENT SIZES, WEIGHTS, QUANTITIES, OR MATERIAL REQUIRE PRIOR APPROVAL BY THE CONSULTING ENGINEER. 5. ALL HVAC INFORMATION IS NOT SHOWN ON THE HVAC DRAWINGS. THE CONTRACTOR SHALL BE RESPONSIBLE FOR COORDINATING INFORMATION ON ALL OTHER CONSTRUCTION DOCUMENTS INCLUDING ARCHITECTURAL, STRUCTURAL, MECHANICAL, AND ELECTRICAL DRAWINGS. 6. THE WORKING DRAWINGS ARE DIAGRAMMATIC. BECAUSE OF THE SMALL SCALE OF THE DRAWINGS, THEY DO NOT SHOW EVERY OFFSET, BEND OR ELBOW NECESSARY FOR THE COMPLETE INSTALLATION IN THE SPACE PROVIDED. ALL LOCATIONS FOR HVAC EQUIPMENT AND PIPING SHALL BE CHECKED AND COORDINATED WITH THE ARCHITECTURAL, MECHANICAL, STRUCTURAL AND ELECTRICAL DRAWINGS. 7. SPACE ABOVE ALL CEILINGS IS EXTREMELY LIMITED. CAREFUL COORDINATION IS REQUIRED WITH ALL TRADES BEFORE ANY PIPE, DUCT, OR EQUIPMENT IS ORDERED AND/OR INSTALLED. 1/8" SCALE SHOP DRAWINGS (SUBMITTED TO BGW FOR APPROVAL) ARE REQUIRED FOR ALL DIVISION 23 WORK. 1/8" SCALE LINDAB DRAWINGS MUST BE REVIEWED BY MECHANICAL CONTRACTOR AND RETURNED TO BGW FOR MODIFICATION PRIOR TO DUCTWORK BEING ORDERED. ANY CONFLICTS AND/OR CHANGES FOUND DURING INSTALLATION THAT RESULT FROM LACK OF COORDINATION BY THE CONTRACTORS DURING THE SHOP DRAWING PROCESS ARE THE RESPONSIBILITY OF THE CONTRACTOR. 8. THE DRAWINGS AND SPECIFICATIONS HAVE BEEN PREPARED TO SUPPLEMENT EACH OTHER AND THEY SHALL BE INTERPRETED AS AN INTEGRAL UNIT WITH THE ITEMS SHOWN ON ONE AND NOT THE OTHER BEING FURNISHED AND INSTALLED AS THOUGH SHOWN AND CALLED OUT IN BOTH. 9. DETAILS: THE CONTRACTOR IS RESPONSIBLE TO REVIEW AND USE WHERE APPROPRIATE ALL OF THE MECHANICAL DETAILS SHOWN ON THE DRAWINGS. DETAILS MAY OR MAY NOT BE CALLED OUT ON THE DRAWINGS WITH SYMBOLS OR KEYED NOTES. ANY CHANGES RESULTING FROM FAILURE TO INSTALL THE MECHANICAL SYSTEM WITHOUT USING THE INCLUDED DETAILS IS THE RESPONSIBILITY OF THE CONTRACTOR. 10. PREPARE 6 COPIES OF SUBMITTALS IN AN INDEXED, LABELED FOLDER CONTAINING FULL PERFORMANCE, MATERIAL AND INSTALLATION INFORMATION ABOUT ALL EQUIPMENT, PIPING, COMPONENTS AND ACCESSORIES TO BE USED. 11. THE STRUCTURE SHOWN ON ALL DETAILS MAY OR MAY NOT PERTAIN TO A PORTION OR ANY PORTION OF THE BUILDING. COORDINATE MOUNTING REQUIREMENTS WITH ARCHITECTURAL AND STRUCTURAL DRAWINGS. 12. ANY PART OF THIS INSTALLATION THAT FAILS, IS UNFIT, OR BECOMES DAMAGED DURING CONSTRUCTION SHALL BE REPAIRED OR REPLACED BY THE CONTRACTOR AT NO ADDITIONAL COST TO THE OWNER. 13. ALL EQUIPMENT SHALL PROVIDE THE SCHEDULED PERFORMANCE AT THE SITE ALTITUDE. 14. ALL EQUIPMENT SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE EQUIPMENT MANUFACTURER'S RECOMMENDATIONS. PROVIDE ALL FITTINGS, TRANSITIONS, VALVES, DAMPERS, AND OTHER DEVICES AND ACCESSORIES REQUIRED FOR A COMPLETE, WORKABLE INSTALLATION. 15. THE MECHANICAL CONTRACTOR SHALL FURNISH ALL REQUIRED MOTORS. ALL MOTOR STARTING EQUIPMENT, WHEN NOT A PART OF THE EQUIPMENT, WILL BE FURNISHED BY THE ELECTRICAL CONTRACTOR. 16. THE ELECTRICAL CONTRACTOR SHALL RUN CONDUIT FOR ALL HVAC CONTROL WIRING. CONDUIT SHALL RUN FROM THERMOSTAT LOCATION TO ABOVE CEILING IN FINISHED AREAS AND TO MECHANICAL UNIT WHERE THERE IS NO CEILING. MECHANICAL CONTRACTOR WILL PROVIDE AND INSTALL PLENUM RATED CABLE. MECHANICAL CONTRACTOR SHALL COORDINATE LOCATION AND QUANTITY OF CONDUIT WITH ELECTRICAL CONTRACTOR. 17. THE CONTRACTOR IS RESPONSIBLE FOR HVAC EQUIPMENT CHECK-IN, SAFEKEEPING, AND DAMAGE. 18. PROPERLY LUBRICATE ALL PIECES OF EQUIPMENT BEFORE TURNING THE SYSTEM OVER TO THE OWNER. 19. TWO OPERATING AND MAINTENANCE MANUALS SHALL BE PROVIDED IN HARD BACK LOOSE LEAF BINDERS. MANUALS SHALL CONTAIN PRODUCT CUT SHEETS AND OPERATING AND MAINTENANCE INSTRUCTIONS ON ALL EQUIPMENT, ACCESSORIES, FIXTURES, VALVES, ETC., PROVIDED FOR THE PROJECT. 20. UPON COMPLETION OF THE WORK, REMOVE ALL SURPLUS MATERIALS AND RUBBISH. MAKE ALL REQUIRED PATCHING AND REPAIRS OF OTHER TRADES' WORK DAMAGED BY THIS CONTRACTOR, AND LEAVE THE PREMISES IN A CLEAN, ORDERLY CONDITION. 21. THE CONTRACTOR SHALL OPERATE THE SYSTEM AND DEMONSTRATE ALL ASPECTS TO THE ENGINEER AND/OR OWNER, TO PROVE ITS OPERATION. ALL FILTERS USED DURING CONSTRUCTION SHALL BE REPLACED PRIOR TO THE TEST RUN PERIOD. 22. THE CONTRACTOR SHALL GUARANTEE THE HVAC SYSTEM INCLUDING DUCTWORK FOR A PERIOD OF ONE YEAR FROM THE DATE OF CERTIFICATE OF OCCUPANCY. CONTRACTOR TO INCLUDE PRICE FOR FIRST YEAR LABOR WARRANTY ON ALL OWNER SUPPLIED EQUIPMENT. 23. THE CONTRACTOR SHALL, DURING CONSTRUCTION, MAINTAIN A SET OF AS-BUILT REDLINED RECORD DRAWINGS AT THE PROJECT SITE. ALL CHANGES IN LAYOUT, ROUTING, EQUIPMENT, COMPONENTS, AND ACCESSORIES SHALL BE RECORDED. THESE REDLINES SHALL BE GIVEN TO THE ARCHITECT/ENGINEER AFTER THE FINAL INSPECTION. HVAC GENERAL NOTES. 24. RECORD DRAWINGS SHALL BE PROVIDED TO THE OWNER, ALONG WITH A COMPLETE SET OF EQUIPMENT OPERATING AND MAINTENANCE MANUALS. REQUIRED ROUTINE MAINTENANCE ACTIONS SHALL BE CLEARLY IDENTIFIED AND THE NAMES AND ADDRESSES OF AT LEAST ONE SERVICE AGENCY SHALL BE PROVIDED. BI-POLAR ION GENERATORS AND MODEL NO. MANUFACTURER IG-1 SYMBOL PLASMA AIR 101C 1,500 120/1/60 ELECTRICAL VOLTS/Ø/Hz 4 WATTS APPROX. WATTS ACCESSORIES AND REMARKS INTERLOCK WITH FAN CIRCUIT SPECIFICATION SECTION 233333 MAX. CFM IG-2 2,500 120/1/60 5 WATTS IG-3 3,500 120/1/60 6 WATTS IG-4 4,000 120/1/60 10 WATTS INTERLOCK WITH FAN CIRCUIT INTERLOCK WITH FAN CIRCUIT INTERLOCK WITH FAN CIRCUIT INSTALLED IN RTU NO. & (QUANTITY) PLASMA AIR 101D PLASMA AIR 101E PLASMA AIR 201D 7(1), 8(1), 13(1), 14(1) 4(1), 9(1) 2(1), 3(1), 6(1) 10(1), 11(1), 12(1), 13(1), 14(1), 15(2) IG-5 5,000 120/1/60 12 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 201E 7(1), 8(1), 13(1), 14(1) IG-6 8,000 120/1/60 30 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 51E 7(1), 8(1), 13(1), 14(1) IG-7 10,000 120/1/60 50 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 51F 7(1), 8(1), 13(1), 14(1) AS ALLOWED BY THE 2009 INTERNATIONAL MECHANICAL CODE AND ASHRAE 62-2004 THE OUTSIDE AIR IN THE BUILDING HAS BEEN REDUCED TO 5 CFM PER PERSON. THE SCHEDULED ION GENERATORS REDUCE THE BUILDING POLLUTANTS AND PROVIDE IMPROVED AIR QUALITY WHILE ACHIEVING ENERGY SAVINGS. IG-8 1,400 120/1/60 1 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 7100 7(1), 8(1), 13(1), 14(1) IG-9 2,800 120/1/60 2 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 7200 7(1), 8(1), 13(1), 14(1) IG-10 4,200 120/1/60 3 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 7300 7(1), 8(1), 13(1), 14(1) IG-11 6,000 120/1/60 4 WATTS INTERLOCK WITH FAN CIRCUIT PLASMA AIR 7400 AC-1(1), AC-2(1) UNITS SUPPLIED BY BGW SUPPLY INC. A DIVISION OF BGW ARCHITECTS THROUGH A NATIONAL ACCOUNT TITUS PAR TITUS PAR TITUS PAR ROOF DOWNBLAST ROOF DOWNBLAST ROOF DOWNBLAST ROOF DOWNBLAST ROOF DOWNBLAST ROOF DOWNBLAST ROOF DOWNBLAST ROOF DOWNBLAST 5 5 5 5 5 5 5 5 75 75 75 75 75 75 WALL SWITCH WALL SWITCH EOC, TAB, & CONTROL SCOPE OF WORK AC-1 SYMBOL SANYO 30K72R MASTER CONTROL 131 SPLIT AIR CONDITIONING UNIT SCHEDULE 208/1/60 SPECIFICATION SECTION 238126 VOLT/Ø/Hz. LOCATION MANUFACTURER AND MODEL NO. 85 ACCESSORIES AND REMARKS 0.5 64 FLA INDOOR UNIT WEIGHT (LBS) 208/1/160 29,800 COOLING CAPACITY (BTUH) 3/8" LIQUID 620-840 CFM RANGE DIMENSIONS W" x H" x D" 60" x 15" x 10" OUTDOOR UNIT VOLT/Ø/Hz. 16.5 143 FLA WEIGHT (LBS) DIMENSIONS W" x H" x D" 39" x 35" x 17" INDOOR TEMP (ºF) 95 REFRIGERANT LINES 5/8" GAS OUTDOOR TEMP (ºF) AC-2 SANYO 30K72R RACK ROOM 133 208/1/60 85 0.5 64 208/1/160 29,800 3/8" 620-840 60" x 15" x 10" 16.5 143 39" x 35" x 17" 95 5/8" TITUS 300FL TITUS 300FL LAY-IN 14" x 14" 10" x 10" 14" x 14" 12" x 12" 16" x 16" 375/600 360º SUPPLY AIR WALL MOUNT TITUS 300FL 12" x 4" 14" x 6" 62" x 18" R-3 TITUS 350FL 500/1100 N/A RETURN AIR WALL MOUNT R-4 0/500 74" x 38" RETURN AIR N/A 26" x 8" R-5 500/1100 N/A RETURN AIR R-6 0/500 14" x 14" RETURN AIR N/A TITUS 350FL TITUS 350FL TITUS 350FL WALL MOUNT WALL MOUNT WALL MOUNT 60" x 16" 72" x 36" 24" x 6" 12" x 12" ACCESSORIES AND REMARKS 8000 SYMBOL RTU-1 25 DESIGN COOLING 79.2 2200 230,139 206,536 62.1 105 DESIGN HEATING MOTOR RPM MOCP 175 152 MCA 5 H.P. TOTAL UNIT 208/3/60 1725 VOLT/Ø/Hz. ELECTRICAL 2625 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) ROOFTOP UNITS SUPPLIED BY BGW SUPPLY INC. A DIVISION OF DCA ARCHITECTS THROUGH A LENNOX NATIONAL ACCOUNT DOWN DISCHARGE ROOFTOP UNIT SCHEDULE (ELECTRIC HEAT) RTU-2 RTU-4 6000 15 77.7 149,359 131,951 61.9 150 145 3 1725 2310 204 204 RTU-3 15 76.5 127,794 61.6 1725 1.0 SPECIFICATION SECTION 237413 MANUFACTURER AND MODEL NO. NOMINAL TONS COOLING NOMINAL HEATING CAPACITY (MBH) TOTAL CFM MIN. O.A. CFM E.S.P. ("Wg) TOTAL CAPACITY SENSIBLE CAPACITY EDB (°F) EWB (°F) O.A. (°F) INPUT (KW) OUTPUT (MBH) OPERATING WEIGHT (LBS.) 2310 204 6000 835 1300 148,756 1.0 1.0 3 150 145 DX COOLING (S)EER EFFICIENCY 10.5 12.0 12.0 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) 5000 RTU-5 12.5 76.8 735 120,203 108,682 61.6 150 134 3 1725 1380 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) RTU-6 RTU-8 6 76.3 61.5 1725 1550 4 76.3 40,561 34,212 61.5 50 47 0.75 1725 761 0.8 153 51 RTU-7 3 75.2 23,466 61.3 1725 0.8 916 745 51 25 2400 1100 75 200 62,376 28,769 52,991 0.8 0.8 2 0.5 50 49 30 25 300 11.2 12.0 12.5 12.8 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) 1), 3), 4), 10), 11), 12), 13), 16), 17), 18) 60.0 60.0 60.0 45.0 15.0 15.0 7.5 ACCESSORIES: 1) ECONOMIZER WITH DUAL SENSIBLE CONTROL. 2) RETURN AIR SMOKE DETECTOR. 3) SUPPLY AIR SMOKE DETECTOR. 4) CO2 SENSOR WALL MOUNTED. 5) HUMIDITROL. 6) VIBRATION ISOLATION CURB. 7) SEISMIC RATED CURB. 8) POWER EXHAUST. 9) HUMIDISTAT. 10) PROGRAMMABLE THERMOSTAT. 11) FACTORY INSTALLED DISCONNECT. 12) STANDARD LENNOX CURB. 13) VERTICAL VENT EXTENSION. 14) COMBUSTION AIR EXTENSION. 15) NETWORK CONTROL PANEL AND SENSORS. 16) GFCI OUTLET, FIELD WIRED. 17) LP KIT-FIELD INSTALLED. 18) COIL GUARDS-FIELD INSTALLED. LENNOX LCH036H4E LENNOX LCH048H4E LENNOX LCH072H4B LENNOX LCH150S4B LENNOX LCH180H4B LENNOX LCH180H4B LENNOX LCH300S4B DOWN DOWN DOWN DOWN DOWN DOWN 105 105 105 105 105 105 8000 25 79.2 2200 230,139 206,536 62.1 105 175 152 5 1725 2625 DOWN 204 1.0 10.5 60.0 LENNOX LCH300S4B 0.3 929 1140 66 1/6 GREENHECK G-097-B 12" 120/1/60 0.3 929 1140 66 1/6 GREENHECK G-097-B 12" 120/1/60 0.3 929 1140 66 1/6 GREENHECK G-097-B 12" 120/1/60 0.3 929 1140 66 1/6 GREENHECK G-097-B 12" 120/1/60 0.3 929 1140 66 1/6 GREENHECK G-097-B 12" 120/1/60 204 204 204 153 51 51 25 204 208/3/60 208/3/60 208/3/60 208/3/60 208/3/60 208/3/60 208/3/60
Transcript of M001 MECHANICAL SCHEDULES & GENcochisetech.net/wp-content/uploads/2016/11/90-Mechanical.pdfb. test...
MECHANIC
AL
SCHED
ULE
S& G
ENER
AL
NOTES
DO NOT SCALE DRAWING
M001
THIS
DR
AWIN
G IS C
LASSIFIE
D A
SP
AR
T O
F A
N U
NP
UB
LISHED
COLL
ECTIO
N O
F V
ISUAL
AR
T.
UND
ER
THE 1978
COP
YR
IGHT
ACT, IT IS A
N E
XCLU
SIV
EOR
IGIN
AL
WOR
K O
F A
UTHOR
SHIP
.NONE O
F T
HE P
ICTOR
IAL,
GR
AP
HIC
OR
TECHNIC
AL
CHAR
TS O
R D
RAWIN
GS
DEP
ICTED
ON T
HIS
SHEET M
AY
BE R
EP
ROD
UCED
OR
TR
ANSM
ITTED
IN A
NY F
OR
M O
RB
Y A
NY M
EANS W
ITHOUT T
HE
EXP
RESS P
RIO
R W
RITTEN
PER
MIS
SIO
N O
F T
HE A
RCHITECT.
THIS
PLA
N IS P
ROD
UCED
ONLY
FOR
THIS
PR
OJE
CT O
N T
HIS
SITE
AND
MAY N
OT B
E U
SED
AT
OTHER
LOCATIO
NS.
SHEET T
ITLE
:
OR
IGIN
AL
ISSUE: P
relim
inar
y
SEAL:
REV
DATE
DESCR
IPTIO
N
SHEET NUMBER:
PR
OJE
CT: A
C489
PR
OJE
CT:
BAP
TIS
T C
HUR
CH
SIE
RR
A V
ISTA, AZ
VILLA
GE M
EAD
OWS
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
41 2 3 5 6
DESCR
IPTIO
N
OR
IGIN
AL
ISSUE
Pr
elim
inar
y0
DANIE
L COOK
AR
CHITECT│
290
9 W
ASHIN
GTO
N B
LVD
- O
GD
EN, UT
8440
1│P
H: 80
0-5
52-
7137│
www.B
GWSER
VIC
ES.c
om
SIE
RR
A V
ISTA, AR
IZONA 8
5635
140
7 S E
L CAM
INO R
EAL
PRELIMINARY D
RAWING!
NOT
FOR C
ONSTR
UCTION!
T
H
C
TITLE
SECTION
SHEET #
MECH ROOF PLAN
DETAIL #
SHEET #
1
EQUIPMENT CALLOUT
SCOPE OF WORK FOR LENNOX PROVIDED EOC, AND MECHANICAL CONTRACTOR CONTROLINSTALLATION AND MECHANICAL CONTRACTOR CONTRACTED INDEPENDENT TEST AND BALANCE.
A. EQUIPMENT OPERATIONS CHECK (EOC) (LENNOX PROVIDED) THROUGH BGWS
• TEST ALL LENNOX EQUIPMENT BASED ON THE STANDARD LENNOX EOC REPORT.• CONTACT LENNOX SUPPORT WITH ANY EQUIPMENT DEFICIENCIES AND COORDINATE REPAIROR REPLACEMENT AS NECESSARY TO ASSIST IN PROVIDING OPERATIONAL EQUIPMENT PRIORTO OPENING DATE.• DISTRIBUTE COPIES OF EOC REPORT AS REQUESTED BY LENNOX.
B. TEST AND BALANCE (TAB) (MECHANICAL CONTRACTOR CONTRACTED)
• UPON ARRIVAL TO THE SITE, INSPECT MECHANICAL SYSTEM AND NOTE ANY DEFICIENCIESTHAT COULD PREVENT PROPER OPERATION AND/OR BALANCING OF THE MECHANICALSYSTEM TO THE OWNER, GENERAL CONTRACTOR AND MECHANICAL CONTRACTOR.• INSPECT ALL MECHANICAL EQUIPMENT FOR PROPER INSTALLATION PER MEP DESIGN.• TEST ALL MECHANICAL EQUIPMENT PER NEBB STANDARDS FOR AIR BALANCE FOR PROPEROPERATION.• THE BALANCING OF THE MECHANICAL SYSTEM WILL BE PERFORMED TO MEET NEBBSTANDARDS UNLESS SPECIFICALLY REQUESTED OTHERWISE, IN WRITING, BY OWNER OROWNERS ENGINEERING FIRM.• BALANCE ALL RTU’S, GRILLS, REGISTERS AND EXHAUST FANS PER MECHANICAL DESIGN ASNOTED ON MEP DRAWINGS PER NEBB STANDARDS FOR AIR BALANCE.• GENERATE A FIELD REPORT OF ANY OUTSTANDING MECHANICAL DEFICIENCIES, IF ANY, THATCOULD NOT BE RESOLVED DURING THE TAB VISIT AND DISTRIBUTE A COPY TO THE OWNER,GENERAL CONTRACTOR AND MECHANICAL CONTRACTOR AND NOTE IF A RE-VISIT WILL BEREQUIRED.• GENERATE A COMPLETE TAB REPORT AND SUBMIT TO THE OWNER AND AS DIRECTED WITHINONE (1) WEEK OF THE COMPLETION OF THE AIR BALANCE.
C. CONTROL INSTALLATION (BGW SUPPLY CONTRACTED CONTROL CONTRACTOR)
• PROVIDE CONTROL INSTALLATION DRAWINGS SHOWING CABLE RUNS ANDLOCATIONS.• PROVIDE AND TERMINATE PLENUM CABLE FOR LENNOX PROVIDED THEROMOSTATS,HUMIDITY SENSORS AND CO2 SENSORS CONDUIT IN SPACE.• PROVIDE, PLENUM COMMUNICATION CABLE BETWEEN RTUS INSTALLED BYELECTRICAL CONTRACTOR.• PROVIDE, AND TERMINATE PLENUM CABLE FOR LENNOX PROVIDED SPACESENSORS AND HUMIDITY SENSORS CONDUIT IN SPACE, IF REQUIRED. WIREINSTALLATION BY ELECTRICAL CONTRACTOR.• PROGRAM AND COMMISSION CONTROLS AS REQUIRED TO MEET OWNERSPECIFICATIONS.• PROVIDE REPORT DETAILING COMMISSION OF CONTROLS AND SUBMIT TOOWNER.• PROVIDE OWNER OPERATORS 2 HOURS OF TRAINING.
D. WARRANTY
• LENNOX PROVIDES A ONE (1) YEAR PARTS WARRANTY ON THE WORKMANSHIP OF ALLLENNOX PROVIDED MATERIAL, AND EQUIPMENT, STARTING AT CERTIFICATE OF OCCUPANCY.
E. CLARIFICATIONS AND RESPONSIBILITY OF MECHANICAL & ELECTRICAL CONTRACTOR
• CONDUIT, RACEWAYS SHALL BE FURNISHED AND INSTALLED BY THE ELECTRICALCONTRACTOR. CONTROL CONTRACTOR WILL REQUIRE A CONDUIT, AND WIRE RACEWAY PATHFOR THE SPACE SENSORS IN AREAS NOT ACCESSIBLE, SUCH AS WALLS, SANCTUARY ANDGYMNASIUM AREAS, SUCH THAT ELECTRICAL CONTRACTOR CAN INSTALL CONTROL WIRE ANDSPACE SENSORS.• CABLE (PROVIDED BY THE CONTROL CONTRACTOR) SHALL BE PULLED OR INSTALLED ATEACH LOCATION SHOWN ON THE CONTROL DRAWINGS. (INSTALLED BY ELECTRICALCONTRACTOR)• ELECTRICAL CONTRACTOR SHALL INSTALL ALL SENSORS AND PANEL.• THE EOC, TAB, AND CONTROL INSTALLATION SCOPE WILL BE COORDINATED WITH THEGENERAL AND/OR MECHANICAL CONTRACTOR.• THE GENERAL OR MECHANICAL CONTRACTOR WILL NOTIFY LENNOX WITH AT LEASTFOURTEEN (14) DAYS ADVANCED NOTICE THAT THE HVAC SYSTEM IS 100% COMPLETE ANDREADY FOR EOC AND CONTROL TERMINATION.O HIGH VOLTAGE MUST BE CONNECTED TO EACH UNITO GAS MUST BE CONNECTED TO EACH UNITO PROPER PHASE ROTATION MUST BE CONFIRMED AT THE DISCONNECTO ALL STAGES OF HEATING AND COOLING MUST BE CONFIRMED OPERATIONALO UNITS CAN BE PUT IN STANDALONE OPERATION BY SETTING THE UNIT OPERATION TO LCONNECTION/RETURN AIR BACK UP MODE. CONSULT THE M-2 PRODIGY CONTROL MANUALFOR INSTRUCTIONS OR CONTACT LENNOX NATIONAL ACCOUNT TECHNICAL SUPPORT1-800-367-6285 FOR ASSISTANCE.• THE MECHANICAL CONTRACTOR WILL PROVIDE A REPRESENTATIVE ON-SITE DURING THEEOC SERVICE TO ADDRESS DEFICIENCIES FOUND. LENNOX WILL MAKE ALL REASONABLEATTEMPTS TO RESOLVE DEFICIENCIES, IF ANY, WITH THE MECHANICAL CONTRACTOR WHILEONSITE.
F. WORKING HOURS• WORKING HOURS SHALL FOLLOW CONSTRUCTIONS HOURS OR AS REQUESTED BY THEGENERAL CONTRACTOR
1
1
RTU1
1
1
1
1
MECHANICAL GENERAL NOTES MECHANICAL LEGEND
DROP
RISE
DROP
20x10
16''Ø
RISE
DROP
RISE
16''Ø
FSD
16x10
FD
SD
E-1CFM
D-1CFM
D-1CFM
20x10
20x10
20x10 14''Ø
12x10
12x10
D-1CFM
D-1CFM
16''Ø 6''Ø
EXHAUST AIR REGISTER - SQUARE
SUPPLY DIFFUSER - SQUARE
FIRE/SMOKE DAMPER
SMOKE DAMPER
LINEAR DIFFUSERS - SIDE MOUNT
FLEXIBLE DUCT
FIRE DAMPER
MANUAL BALANCING DAMPER
SLOPED DUCT DROP
SLOPED DUCT RISE
FLAT OVAL DUCT
DUCT - RISE
UNDER FLOOR ROUND DUCT
POSITIVE PRESSURE DUCT - DROP
ROUND DUCT
RECTANGULAR DUCT
ROUND DUCT - DROP
ROUND DUCT - RISE
SOUND ATTENUATOR
ROUND TO ROUND TRANSITION
RECTANGULAR TRANSITION - OFFSET
RECTANGULAR TO ROUND TRANSITION
RECTANGULAR TRANSITION
LINEAR DIFFUSER - BOTTOM MOUNT
SUPPLY DIFFUSER - ROUND
SECTION CALLOUT
DETAIL CALLOUT
THERMOSTAT OR TEMPERATURE SENSOR
HUMIDISTAT
CARBON DIOXIDE DETECTOR
POINT OF CONNECTION
POINT OF DEMOLITION
REVISION DELTA
KEYED NOTE CALLOUT
M3011
SCALE: 1/8" = 1' - 0"
M5011
R-1CFM RETURN AIR REGISTER - SQUARE
92ºF Db SUMMER
HVAC DESIGN DATA
OUTSIDE DESIGN TEMPS.: 64ºF Wb SUMMER17ºF Db WINTER
DESIGN ALTITUDE: 175 FT.
INTERIOR DESIGN DATA
ALL
SUMMER WINTER
Db
75º
%HUMIDITY
50% 72º 40%
Db %HUMIDITY
NOTE:
ALL ROUND DUCTWORK, FITTINGS AND VOLUME CONTROL DAMPERS ARE TO BESPIROSAFE GASKETED DUCT MANUFACTURED BY LINDAB. BGW HAS A NATIONALACCOUNT AGREEMENT WITH LINDAB INC. FOR THIS PROJECT CONTACT LINDABTAKE OFF DEPARTMENT AT (757) 488-7234 EXT. 381 FOR SPIRAL DUCT QUOTATION.
THE DRAWINGS INDICATE DIAGRAMMATICALLY THE EXTENT OF THE WORK. DUE TOTHE SCALE OF THE DRAWINGS, OFFSET, FITTINGS, AND ACCESSORIES MAY NOT BEINDICATED. WORK INDICATED, BUT HAVING DETAILS OMITTED, SHALL BECOMPLETELY PROVIDED BY CONTRACTOR TO PERFORM FUNCTION INTENDED ATNO ADDITIONAL COST.
CONTRACTOR SHALL EXAMINE THE ARCHITECTURAL, STRUCTURAL, PLUMBING,MECHANICAL, AND ELECTRICAL DRAWINGS AND SPECIFICATIONS TO AVOIDCONFLICT WITH OTHER TRADES. MINOR VARIATIONS IN LOCATION OF EQUIPMENTSHALL BE MADE ON WRITTEN APPROVAL OF THE ENGINEER AT NO ADDITIONALCOST.
MECHANICAL CONTRACTOR IS RESPONSIBLE FOR PAYMENT, ORDERING, DELIVERYCOORDINATION RECEIVING AND INSTALLATION OF ALL THE LINDAB SUPPLIEDMATERIAL.
THE CONTRACTOR IS REQUIRED TO REVIEW THE MECHANICAL DRAWINGS,MAKING ANY NECESSARY MODIFICATIONS TO ACCOUNT FOR FIELD VARIANCESAND SEND THESE FINAL DRAWINGS TO LINDAB FOR A DUCT QUOTATION. THESEREVISED PLANS ARE TO BE E-MAILED 72 HOURS BEFORE BID TIME TO LINDAB TAKEOFF FOR A PRODUCT QUOTATION.
THE CONTRACTOR MUST APPROVE THE FINAL DUCT DRAWINGS AND BILL OFMATERIAL BEFORE PLACING THE ORDER WITH LINDAB.
NOTE:
MECHANICAL CONTRACTOR TO REVIEW ALL DRAWINGSFOR CONFLICTS WITH STRUCTURE AND OTHER TRADES.MECHANICAL CONTRACTOR TO RESOLVE ALL CONFLICTSWITH ENGINEER PRIOR TO ORDERING, FABRICATING ORINSTALLING DUCTWORK.
NOTE:
1) SPACE ABOVE CEILING IS TO BE USED AS A RETURN AIRPLENUM. ALL MATERIALS TO BE PLENUM RATED.
2) ALL TERMINAL SUPPLY DUCT BRANCHES TO BEEQUIPPED WITH MANUAL BALANCING DAMPER.
3) FLEX DUCT (MAXIMUM 60" LONG) TYPICAL ON EACHDIFFUSER EXCEPT IN EXPOSED APPLICATIONS.
4) PROVIDE TURNING VANES IN ALL RECTANGULARELBOWS. �
EF-1
SYMBOL
GREENHECK G-123-B ROOF
CFM
ARRANGEMENT,ROTATION &DISCHARGE
DOWNBLAST 825
EXHAUST FAN SCHEDULE
0.35 12"
SPECIFICATIONSECTION 233423
HEIGHTABOVE ROOF
(INCHES)SP "WGTYPEMANUFACTURER AND
MODEL NO.
OPERATINGWEIGHT
(LBS.)ACCESSORIES AND
REMARKS
995
RPM
FANDETAIL
NO. RPM
MOTOR
1140
H.P.
ELECTRICAL
VOLT/Ø/Hz.
76
CONTROLMETHOD
1/6
EF-2
EF-3 150 0.35 12"1323 1550 471/20
EF-4
GREENHECK G-080-D WALL SWITCH
EF-5
5
0.3929 1140 661/6GREENHECK G-097-B
EF-6
EF-7
EF-8
120/1/60 BACKDRAFT DAMPER
GREENHECK G-123-B 750 0.35 12" WALL SWITCH958 1140 761/6 BACKDRAFT DAMPER
BACKDRAFT DAMPER
BACKDRAFT DAMPER
BACKDRAFT DAMPER
WALL SWITCH
WALL SWITCH
12"
BACKDRAFT DAMPERWALL SWITCH
BACKDRAFT DAMPERWALL SWITCH
BACKDRAFT DAMPERWALL SWITCH
EF-9 BACKDRAFT DAMPER
24" x 24"
OVERALLSIZE
DIFFUSER AND GRILLE SCHEDULE
D-1
SYMBOL
TITUS TMS
MIN./MAX.CFM
0/100 4-WAY
BLOW
6"Ø
NECKSIZE
SUPPLY AIR
TYPEACCESSORIESAND REMARKS
LAY-IN
D-2 TITUS TMS 100/240 8"Ø
D-3 TITUS TMS 240/400 10"Ø
24" x 24"4-WAY SUPPLY AIR
24" x 24"4-WAY SUPPLY AIR
LAY-IN
LAY-IN
SPECIFICATIONSECTION 233713
MANUFACTURER ANDMODEL NO.
D-4 TITUS TMS 400/520 12"Ø24" x 24"4-WAY SUPPLY AIR LAY-IN
D-7
250/425 360º SUPPLY AIR NECK MOUNT
D-8
375/600 360º SUPPLY AIR NECK MOUNT
24" x 24"E-1 0/130 4-WAY 6"Ø LAY-IN
E-2 130/260 8"Ø
E-3 260/400 10"Ø
24" x 24"4-WAY
24" x 24"4-WAY
LAY-IN
LAY-IN
24" x 24"D-5 TITUS 300FL 0/130 4-WAY SUPPLY AIR
D-6
24" x 24"R-1 TITUS PXP 500/1100 N/A RETURN AIR LAY-IN
R-2 TITUS PXP 0/500 24" x 12" LAY-INRETURN AIRN/A
N/A
N/A
EXHAUST AIR
EXHAUST AIR
EXHAUST AIR
120/1/60
120/1/60
120/1/60
1. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT NECESSARY TO CONSTRUCT A COMPLETE, OPERATIONAL HVAC SYSTEM FOR THEENTIRE PROJECT AS SHOWN ON THESE DRAWINGS, INCLUDING ALL NECESSARY FEES AND PERMITS.
2. THE ENTIRE INSTALLATION SHALL CONFORM TO THE MOST RECENTLY ADOPTED REQUIREMENTS OF THE INTERNATIONAL MECHANICALCODE, INTERNATIONAL PLUMBING CODE, INTERNATIONAL BUILDING CODE, AND ALL OTHER APPLICABLE CITY, COUNTY, AND STATE CODESAND REGULATIONS IN EFFECT AT THE DATE OF THE PERMITTING.
3. COORDINATE THE INSTALLATION OF ALL HVAC PIPING, DUCTWORK, AND EQUIPMENT WITH PLUMBING PIPING, PLUMBING EQUIPMENT, FIREPROTECTION PIPING AND ALL OTHER TRADES INCLUDING BUT NOT LIMITED TO: THE MECHANICAL CONTRACTOR, ELECTRICALCONTRACTOR, FIRE PROTECTION CONTRACTOR, GENERAL CONTRACTOR, AND ANY CONTRACTOR HIRED DIRECTLY BY THE OWNER PRIORTO FABRICATION AND INSTALLATION. WHERE CONFLICTS MAY OCCUR, THEY SHALL BE RESOLVED PRIOR TO INSTALLATION.
4. THE DRAWINGS SHOW THE GENERAL DESIGN, ARRANGEMENTS AND THE EXTENT OF THE SYSTEM. IT SHALL BE THE WORK OF THECONTRACTOR TO MAKE SUCH SLIGHT ALTERATIONS AS MAY BE NECESSARY TO MAKE THE SYSTEM COMPLETE AND OPERATIONAL INACCORDANCE WITH THE DESIGN INTENT. MAJOR DEVIATIONS SUCH AS CHANGES IN COMPONENT SIZES, WEIGHTS, QUANTITIES, ORMATERIAL REQUIRE PRIOR APPROVAL BY THE CONSULTING ENGINEER.
5. ALL HVAC INFORMATION IS NOT SHOWN ON THE HVAC DRAWINGS. THE CONTRACTOR SHALL BE RESPONSIBLE FOR COORDINATINGINFORMATION ON ALL OTHER CONSTRUCTION DOCUMENTS INCLUDING ARCHITECTURAL, STRUCTURAL, MECHANICAL, AND ELECTRICALDRAWINGS.
6. THE WORKING DRAWINGS ARE DIAGRAMMATIC. BECAUSE OF THE SMALL SCALE OF THE DRAWINGS, THEY DO NOT SHOW EVERY OFFSET,BEND OR ELBOW NECESSARY FOR THE COMPLETE INSTALLATION IN THE SPACE PROVIDED. ALL LOCATIONS FOR HVAC EQUIPMENT ANDPIPING SHALL BE CHECKED AND COORDINATED WITH THE ARCHITECTURAL, MECHANICAL, STRUCTURAL AND ELECTRICAL DRAWINGS.
7. SPACE ABOVE ALL CEILINGS IS EXTREMELY LIMITED. CAREFUL COORDINATION IS REQUIRED WITH ALL TRADES BEFORE ANY PIPE, DUCT,OR EQUIPMENT IS ORDERED AND/OR INSTALLED. 1/8" SCALE SHOP DRAWINGS (SUBMITTED TO BGW FOR APPROVAL) ARE REQUIRED FORALL DIVISION 23 WORK. 1/8" SCALE LINDAB DRAWINGS MUST BE REVIEWED BY MECHANICAL CONTRACTOR AND RETURNED TO BGW FORMODIFICATION PRIOR TO DUCTWORK BEING ORDERED. ANY CONFLICTS AND/OR CHANGES FOUND DURING INSTALLATION THAT RESULTFROM LACK OF COORDINATION BY THE CONTRACTORS DURING THE SHOP DRAWING PROCESS ARE THE RESPONSIBILITY OF THECONTRACTOR.
8. THE DRAWINGS AND SPECIFICATIONS HAVE BEEN PREPARED TO SUPPLEMENT EACH OTHER AND THEY SHALL BE INTERPRETED AS ANINTEGRAL UNIT WITH THE ITEMS SHOWN ON ONE AND NOT THE OTHER BEING FURNISHED AND INSTALLED AS THOUGH SHOWN AND CALLEDOUT IN BOTH.
9. DETAILS: THE CONTRACTOR IS RESPONSIBLE TO REVIEW AND USE WHERE APPROPRIATE ALL OF THE MECHANICAL DETAILS SHOWN ONTHE DRAWINGS. DETAILS MAY OR MAY NOT BE CALLED OUT ON THE DRAWINGS WITH SYMBOLS OR KEYED NOTES. ANY CHANGESRESULTING FROM FAILURE TO INSTALL THE MECHANICAL SYSTEM WITHOUT USING THE INCLUDED DETAILS IS THE RESPONSIBILITY OF THECONTRACTOR.
10. PREPARE 6 COPIES OF SUBMITTALS IN AN INDEXED, LABELED FOLDER CONTAINING FULL PERFORMANCE, MATERIAL AND INSTALLATIONINFORMATION ABOUT ALL EQUIPMENT, PIPING, COMPONENTS AND ACCESSORIES TO BE USED.
11. THE STRUCTURE SHOWN ON ALL DETAILS MAY OR MAY NOT PERTAIN TO A PORTION OR ANY PORTION OF THE BUILDING. COORDINATEMOUNTING REQUIREMENTS WITH ARCHITECTURAL AND STRUCTURAL DRAWINGS.
12. ANY PART OF THIS INSTALLATION THAT FAILS, IS UNFIT, OR BECOMES DAMAGED DURING CONSTRUCTION SHALL BE REPAIRED ORREPLACED BY THE CONTRACTOR AT NO ADDITIONAL COST TO THE OWNER.
13. ALL EQUIPMENT SHALL PROVIDE THE SCHEDULED PERFORMANCE AT THE SITE ALTITUDE.
14. ALL EQUIPMENT SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE EQUIPMENT MANUFACTURER'S RECOMMENDATIONS. PROVIDEALL FITTINGS, TRANSITIONS, VALVES, DAMPERS, AND OTHER DEVICES AND ACCESSORIES REQUIRED FOR A COMPLETE, WORKABLEINSTALLATION.
15. THE MECHANICAL CONTRACTOR SHALL FURNISH ALL REQUIRED MOTORS. ALL MOTOR STARTING EQUIPMENT, WHEN NOT A PART OF THEEQUIPMENT, WILL BE FURNISHED BY THE ELECTRICAL CONTRACTOR.
16. THE ELECTRICAL CONTRACTOR SHALL RUN CONDUIT FOR ALL HVAC CONTROL WIRING. CONDUIT SHALL RUN FROM THERMOSTATLOCATION TO ABOVE CEILING IN FINISHED AREAS AND TO MECHANICAL UNIT WHERE THERE IS NO CEILING. MECHANICAL CONTRACTORWILL PROVIDE AND INSTALL PLENUM RATED CABLE. MECHANICAL CONTRACTOR SHALL COORDINATE LOCATION AND QUANTITY OF CONDUITWITH ELECTRICAL CONTRACTOR.
17. THE CONTRACTOR IS RESPONSIBLE FOR HVAC EQUIPMENT CHECK-IN, SAFEKEEPING, AND DAMAGE.
18. PROPERLY LUBRICATE ALL PIECES OF EQUIPMENT BEFORE TURNING THE SYSTEM OVER TO THE OWNER.
19. TWO OPERATING AND MAINTENANCE MANUALS SHALL BE PROVIDED IN HARD BACK LOOSE LEAF BINDERS. MANUALS SHALL CONTAINPRODUCT CUT SHEETS AND OPERATING AND MAINTENANCE INSTRUCTIONS ON ALL EQUIPMENT, ACCESSORIES, FIXTURES, VALVES, ETC.,PROVIDED FOR THE PROJECT.
20. UPON COMPLETION OF THE WORK, REMOVE ALL SURPLUS MATERIALS AND RUBBISH. MAKE ALL REQUIRED PATCHING AND REPAIRS OFOTHER TRADES' WORK DAMAGED BY THIS CONTRACTOR, AND LEAVE THE PREMISES IN A CLEAN, ORDERLY CONDITION.
21. THE CONTRACTOR SHALL OPERATE THE SYSTEM AND DEMONSTRATE ALL ASPECTS TO THE ENGINEER AND/OR OWNER, TO PROVE ITSOPERATION. ALL FILTERS USED DURING CONSTRUCTION SHALL BE REPLACED PRIOR TO THE TEST RUN PERIOD.
22. THE CONTRACTOR SHALL GUARANTEE THE HVAC SYSTEM INCLUDING DUCTWORK FOR A PERIOD OF ONE YEAR FROM THE DATE OFCERTIFICATE OF OCCUPANCY. CONTRACTOR TO INCLUDE PRICE FOR FIRST YEAR LABOR WARRANTY ON ALL OWNER SUPPLIED EQUIPMENT.
23. THE CONTRACTOR SHALL, DURING CONSTRUCTION, MAINTAIN A SET OF AS-BUILT REDLINED RECORD DRAWINGS AT THE PROJECT SITE.ALL CHANGES IN LAYOUT, ROUTING, EQUIPMENT, COMPONENTS, AND ACCESSORIES SHALL BE RECORDED. THESE REDLINES SHALL BEGIVEN TO THE ARCHITECT/ENGINEER AFTER THE FINAL INSPECTION.HVAC GENERAL NOTES.
24. RECORD DRAWINGS SHALL BE PROVIDED TO THE OWNER, ALONG WITH A COMPLETE SET OF EQUIPMENT OPERATING ANDMAINTENANCE MANUALS. REQUIRED ROUTINE MAINTENANCE ACTIONS SHALL BE CLEARLY IDENTIFIED AND THE NAMES AND ADDRESSES OFAT LEAST ONE SERVICE AGENCY SHALL BE PROVIDED.
BI-POLAR ION GENERATORS
AND MODEL NO.MANUFACTURER
IG-1
SYMBOL
PLASMA AIR 101C 1,500 120/1/60
ELECTRICAL
VOLTS/Ø/Hz
4 WATTS
APPROX. WATTS
ACCESSORIESAND REMARKS
INTERLOCK WITH FAN CIRCUIT
SPECIFICATIONSECTION233333
MAX. CFM
IG-2 2,500 120/1/60 5 WATTS
IG-3 3,500 120/1/60 6 WATTS
IG-4 4,000 120/1/60 10 WATTS
INTERLOCK WITH FAN CIRCUIT
INTERLOCK WITH FAN CIRCUIT
INTERLOCK WITH FAN CIRCUIT
INSTALLED IN RTUNO. & (QUANTITY)
PLASMA AIR 101D
PLASMA AIR 101E
PLASMA AIR 201D 7(1), 8(1), 13(1), 14(1)
4(1), 9(1)
2(1), 3(1), 6(1)
10(1), 11(1), 12(1), 13(1), 14(1), 15(2)
IG-5 5,000 120/1/60 12 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 201E 7(1), 8(1), 13(1), 14(1)
IG-6 8,000 120/1/60 30 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 51E 7(1), 8(1), 13(1), 14(1)
IG-7 10,000 120/1/60 50 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 51F 7(1), 8(1), 13(1), 14(1)
AS ALLOWED BY THE 2009 INTERNATIONAL MECHANICAL CODE AND ASHRAE 62-2004 THE OUTSIDE AIR IN THE BUILDING HAS BEEN REDUCED TO 5 CFM PER PERSON.THE SCHEDULED ION GENERATORS REDUCE THE BUILDING POLLUTANTS AND PROVIDE IMPROVED AIR QUALITY WHILE ACHIEVING ENERGY SAVINGS.
IG-8 1,400 120/1/60 1 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 7100 7(1), 8(1), 13(1), 14(1)
IG-9 2,800 120/1/60 2 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 7200 7(1), 8(1), 13(1), 14(1)
IG-10 4,200 120/1/60 3 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 7300 7(1), 8(1), 13(1), 14(1)
IG-11 6,000 120/1/60 4 WATTS INTERLOCK WITH FAN CIRCUITPLASMA AIR 7400 AC-1(1), AC-2(1)
UNITS SUPPLIED BY BGW SUPPLY INC. A DIVISION OF BGW ARCHITECTS THROUGH A NATIONAL ACCOUNT
TITUS PAR
TITUS PAR
TITUS PAR
ROOF DOWNBLAST
ROOF DOWNBLAST
ROOF DOWNBLAST
ROOF DOWNBLAST
ROOF DOWNBLAST
ROOF DOWNBLAST
ROOF DOWNBLAST
ROOF DOWNBLAST
5
5
5
5
5
5
5
5
75
75
75
75
75
75
WALL SWITCH
WALL SWITCH
EOC, TAB, & CONTROL SCOPE OF WORK
AC-1
SYMBOL
SANYO 30K72R MASTERCONTROL 131
SPLIT AIR CONDITIONING UNIT SCHEDULE
208/1/60
SPECIFICATIONSECTION 238126
VOLT/Ø/Hz.LOCATIONMANUFACTURER AND
MODEL NO.
85
ACCESSORIES ANDREMARKS
0.564
FLA
INDOOR UNITWEIGHT
(LBS)
208/1/16029,800
COOLINGCAPACITY
(BTUH)
3/8"
LIQUID
620-840
CFMRANGE
DIMENSIONSW" x H" x D"
60" x 15" x 10"
OUTDOOR UNIT
VOLT/Ø/Hz.
16.5143
FLAWEIGHT
(LBS)DIMENSIONSW" x H" x D"
39" x 35" x 17"
INDOORTEMP (ºF)
95
REFRIGERANTLINES
5/8"
GASOUTDOORTEMP (ºF)
AC-2 SANYO 30K72R RACKROOM 133 208/1/60 850.564 208/1/16029,800 3/8"620-840 60" x 15" x 10" 16.514339" x 35" x 17" 955/8"
TITUS 300FL
TITUS 300FL
LAY-IN14" x 14"
10" x 10"
14" x 14"
12" x 12"
16" x 16"
375/600 360º SUPPLY AIR WALL MOUNTTITUS 300FL 12" x 4"14" x 6"
62" x 18"R-3 TITUS 350FL 500/1100 N/A RETURN AIR WALL MOUNT
R-4 0/500 74" x 38" RETURN AIRN/A
26" x 8"R-5 500/1100 N/A RETURN AIR
R-6 0/500 14" x 14" RETURN AIRN/A
TITUS 350FL
TITUS 350FL
TITUS 350FL
WALL MOUNT
WALL MOUNT
WALL MOUNT
60" x 16"
72" x 36"
24" x 6"
12" x 12"
ACCESSORIES ANDREMARKS
8000
SYMBOL
RTU-1 25
DESIGN COOLING
79.22200 230,139 206,536 62.1 105
DESIGN HEATINGMOTOR
RPMMOCP
175152
MCA
5
H.P.
TOTAL UNIT
208/3/60 1725
VOLT/Ø/Hz.
ELECTRICAL
2625 1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
ROOFTOP UNITS SUPPLIED BY BGW SUPPLY INC. A DIVISION OF DCA ARCHITECTS THROUGH A LENNOX NATIONAL ACCOUNT
DOWN
DISCHARGE
ROOFTOP UNIT SCHEDULE (ELECTRIC HEAT)
RTU-2
RTU-4 600015 77.7149,359 131,951 61.9 150145 3 1725 2310
204
204
RTU-3 15 76.5127,794 61.6 17251.0
SPECIFICATIONSECTION 237413
MANUFACTURER ANDMODEL NO.
NOMINALTONS
COOLING
NOMINALHEATINGCAPACITY
(MBH)TOTALCFM
MIN. O.A.CFM
E.S.P.("Wg)
TOTALCAPACITY
SENSIBLECAPACITY
EDB(°F)
EWB(°F)
O.A.(°F)
INPUT(KW)
OUTPUT(MBH)
OPERATINGWEIGHT
(LBS.)
2310204 6000 835
1300
148,756
1.0
1.0
3150145
DX COOLING
(S)EER
EFFICIENCY
10.5
12.0
12.0
1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
5000RTU-5 12.5 76.8735 120,203 108,682 61.6 150134 3 1725 1380 1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
RTU-6
RTU-8
6 76.3 61.5 1725
15504 76.340,561 34,212 61.5 5047 0.75 1725 761
0.8
153
51
RTU-7 3 75.223,466 61.3 17250.8
916
745
51
25
2400
1100 75
200
62,376
28,769
52,991
0.8
0.8
2
0.5
5049
3025
300
11.2
12.0
12.5
12.8
1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
1), 3), 4), 10), 11), 12), 13), 16), 17), 18)
60.0
60.0
60.0
45.0
15.0
15.0
7.5
ACCESSORIES: 1) ECONOMIZER WITH DUAL SENSIBLE CONTROL. 2) RETURN AIR SMOKE DETECTOR. 3) SUPPLY AIR SMOKE DETECTOR. 4) CO2 SENSOR WALL MOUNTED. 5) HUMIDITROL. 6) VIBRATION ISOLATION CURB. 7) SEISMIC RATED CURB. 8) POWER EXHAUST. 9) HUMIDISTAT. 10) PROGRAMMABLE THERMOSTAT. 11) FACTORY INSTALLED DISCONNECT. 12) STANDARD LENNOX CURB. 13) VERTICAL VENT EXTENSION. 14) COMBUSTION AIR EXTENSION. 15) NETWORK CONTROL PANEL AND SENSORS. 16) GFCI OUTLET, FIELD WIRED.17) LP KIT-FIELD INSTALLED. 18) COIL GUARDS-FIELD INSTALLED.
LENNOX LCH036H4E
LENNOX LCH048H4E
LENNOX LCH072H4B
LENNOX LCH150S4B
LENNOX LCH180H4B
LENNOX LCH180H4B
LENNOX LCH300S4B
DOWN
DOWN
DOWN
DOWN
DOWN
DOWN
105
105
105
105
105
105
800025 79.22200 230,139 206,536 62.1 105 175152 5 1725 2625DOWN 204 1.0 10.560.0LENNOX LCH300S4B
0.3929 1140 661/6GREENHECK G-097-B 12" 120/1/60
0.3929 1140 661/6GREENHECK G-097-B 12" 120/1/60
0.3929 1140 661/6GREENHECK G-097-B 12" 120/1/60
0.3929 1140 661/6GREENHECK G-097-B 12" 120/1/60
0.3929 1140 661/6GREENHECK G-097-B 12" 120/1/60
204
204
204
153
51
51
25
204 208/3/60
208/3/60
208/3/60
208/3/60
208/3/60
208/3/60
208/3/60
MECHANIC
AL
FLO
OR
PLA
N
DO NOT SCALE DRAWING
M101
THIS
DR
AWIN
G IS C
LASSIFIE
D A
SP
AR
T O
F A
N U
NP
UB
LISHED
COLL
ECTIO
N O
F V
ISUAL
AR
T.
UND
ER
THE 1978
COP
YR
IGHT
ACT, IT IS A
N E
XCLU
SIV
EOR
IGIN
AL
WOR
K O
F A
UTHOR
SHIP
.NONE O
F T
HE P
ICTOR
IAL,
GR
AP
HIC
OR
TECHNIC
AL
CHAR
TS O
R D
RAWIN
GS
DEP
ICTED
ON T
HIS
SHEET M
AY
BE R
EP
ROD
UCED
OR
TR
ANSM
ITTED
IN A
NY F
OR
M O
RB
Y A
NY M
EANS W
ITHOUT T
HE
EXP
RESS P
RIO
R W
RITTEN
PER
MIS
SIO
N O
F T
HE A
RCHITECT.
THIS
PLA
N IS P
ROD
UCED
ONLY
FOR
THIS
PR
OJE
CT O
N T
HIS
SITE
AND
MAY N
OT B
E U
SED
AT
OTHER
LOCATIO
NS.
SHEET T
ITLE
:
OR
IGIN
AL
ISSUE: P
relim
inar
y
SEAL:
REV
DATE
DESCR
IPTIO
N
SHEET NUMBER:
PR
OJE
CT: A
C489
PR
OJE
CT:
BAP
TIS
T C
HUR
CH
SIE
RR
A V
ISTA, AZ
VILLA
GE M
EAD
OWS
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
41 2 3 5 6
DESCR
IPTIO
N
OR
IGIN
AL
ISSUE
Pr
elim
inar
y0
DANIE
L COOK
AR
CHITECT│
290
9 W
ASHIN
GTO
N B
LVD
- O
GD
EN, UT
8440
1│P
H: 80
0-5
52-
7137│
www.B
GWSER
VIC
ES.c
om
SIE
RR
A V
ISTA, AR
IZONA 8
5635
140
7 S E
L CAM
INO R
EAL
PRELIMINARY D
RAWING!
NOT
FOR C
ONSTR
UCTION!
1
2
MANUAL BALANCING DAMPER (TYPICAL).
CONTROL PANEL LOCATION.
KEYED NOTES
NOTE:
1) SPACE ABOVE CEILING IS TO BE USED AS A RETURN AIR PLENUM. ALL MATERIALS TO BE PLENUMRATED.
2) ALL TERMINAL SUPPLY DUCT BRANCHES TO BE EQUIPPED WITH MANUAL BALANCING DAMPER.
3) FLEX DUCT (MAXIMUM 60" LONG) TYPICAL ON EACH DIFFUSER EXCEPT IN EXPOSED APPLICATIONS.
4) PROVIDE TURNING VANES IN ALL RECTANGULAR ELBOWS.�
NOTE:
MECHANICAL CONTRACTOR TO REVIEW ALL DRAWINGS FOR CONFLICTS WITH STRUCTURE AND OTHERTRADES. MECHANICAL CONTRACTOR TO RESOLVE ALL CONFLICTS WITH ENGINEER PRIOR TO ORDERING,FABRICATING OR INSTALLING DUCTWORK.
R1
R2
R5
R4
DW
d d
B.9
14
UP TO EF-3
UP TO EF-4
UP TO EF-2
UP TO EF-5
UP TO EF-6
UP TO EF-7
UP TO EF-8
UP TO EF-9
UP TO EF-1
UP TO RTU-5
UP TO RTU-3
UP TO RTU-2
UP TO RTU-4
UP TO RTU-1
UP TORTU-6
UP TO RTU-7
UP TO RTU-8
6"Ø 6"Ø
6"Ø
6"Ø
6"Ø
6"Ø
6"Ø
6"Ø6"Ø
8"Ø
10"Ø
10"Ø
10"Ø14"Ø10"Ø10"Ø
10"Ø
10"Ø10"Ø
14"Ø
8"Ø
40x32
40x32
26"Ø26"Ø
10"Ø
10"Ø
14"Ø
14"Ø
14"Ø
14"Ø
14"Ø
14"Ø
24"Ø
20"Ø
18"Ø
22"Ø
14"Ø
14"Ø 14"Ø
14"Ø
14"Ø
16"Ø
20"Ø
22"Ø24"Ø
14"Ø
14"Ø
14"Ø
28"Ø
30"Ø
10"Ø
40x32
40x32
14"Ø
14"Ø
14"Ø
18"Ø
20"Ø
14"Ø
22"Ø14"Ø
10"Ø
24"Ø
26"Ø
14"Ø
26"Ø
14"Ø
24"Ø
28"Ø
30"Ø
14"Ø
14"Ø
14"Ø
14"Ø14"Ø
14"Ø
22"Ø20"Ø
16"Ø
1
1
8"Ø
16"Ø10"Ø10"Ø10"Ø 14"Ø
10"Ø8"Ø
1
20x14
10"Ø
18"Ø
18x18 8"Ø
10"Ø10"Ø
14"Ø12"Ø
6"Ø
6"Ø6"Ø
6"Ø10"Ø
10"Ø
1
20x18
6"Ø
12"Ø 10"Ø
10"Ø
14"Ø
8"Ø12"Ø
12"Ø
16"Ø
18"Ø
14"Ø
12"Ø
10"Ø
10"Ø
6"Ø
1
48x20
30x26
26"Ø 20"Ø
10"Ø
10"Ø10"Ø
10"Ø14"Ø
12"Ø
10"Ø
10"Ø
8"Ø
16"Ø
14"Ø
10"Ø
10"Ø
10"Ø
24"Ø
10"Ø18"Ø
18"Ø
16"Ø
16"Ø
12"Ø
10"Ø
6"Ø
8"Ø
10"Ø
6"Ø
10"Ø
10"Ø
18"Ø
8"Ø
16"Ø
12"Ø
10"Ø
8"Ø
12"Ø 12"ØSLOPE DOWN
DROP
28x24
28x24
10"Ø
8"Ø
16"Ø
14"Ø
12"Ø
10"Ø
6"Ø
8"Ø
8"Ø
8"Ø
8"Ø
8"Ø
24"Ø
14"Ø
10"Ø
12"Ø
8"Ø
8"Ø8"Ø
8"Ø
20"Ø 16"Ø
10"Ø
14"Ø
6"Ø
8"Ø
8"Ø
8"Ø
8"Ø
8"Ø
18"Ø
16"Ø
10"Ø
10"Ø
10"Ø
10"Ø
10"Ø
6"Ø
10"Ø
6"Ø
6"Ø
10"Ø
1
1
FSD
FSD FSD
FSD
FSD
T
T
T
TC
TC
T
T C
TC
26x16
40x24
40x24
24x24
24x24
26x20
18x12
DROP
8"Ø
22"Ø
22"Ø
12"Ø
8"Ø
10"Ø
14"Ø14"Ø
AC1AC
2
21'-0" A.F.F.
21'-0" A.F.F.21'-0" A.F.F.
21'-0" A.F.F.
15'-0" A.F.F.15'-0" A.F.F.15'-0" A.F.F.
15'-0" A.F.F.
15'-0" A.F.F.
9'-6" A.F.F.9'-6" A.F.F.
12'-0" A.F.F.
20'-0" A.F.F.
20'-0" A.F.F.
20'-10" A.F.F. 20'-10" A.F.F.
12'-0" A.F.F.
CHAPEL101
FOYER102
CATERING103
USHER104 VESTIBULE
106
PLAY ROOM107
CLASSROOM A108
R.R.109
CLASSROOM B110
R.R.111
CLASSROOM C112
CRAWLERS113
CHECK-IN114 R.R.
115
INFANTS116
OFFICE117
MEN'S118
JAN.119
CORRIDOR120
stg.121
R.R.122 STG.
123
TACTILE124
MOTOR SKILLS125
SENSORY126
MINISTRY127
COUNS.128
FAM. R.R.129
BACKSTAGE/STORAGE130
MASTER CONTROL131
BACK STAGE132
RACK ROOM133
GREEN ROOM134
R.R.135
MAN CAVE136
R.R.137
COUNS.138
BRIDE'S ROOM139
CORRIDOR140
JAN.141
WOMEN'S142
SPRK.143
STORAGE144
HOSPITALITY145
SANCTUARY147
PLATFORM148
CAFE150
san.149
MDP143.1
CHANGING146.1
26"Ø
u u
1
18
187
A A
B B
r r
j
15
15 17
n n
C C
165
5
2
3 9 10 1211
f
l
o o
q
t
6
e
h
4 8 13
p
s
m
k
G
R3
R3
6.1 6.9
h.9
26"Ø
14"Ø
500D-5 500
D-5
500D-5
500D-5
500D-5
500D-5
500D-5
500D-5
500D-5
500D-5
530D-7
530D-7
530D-7
530D-7
530D-7
530D-7
530D-7
530D-7530
D-7
530D-7
150E-2
150E-2
370D-3
225D-3
160D-2
255D-3
70D-1
90D-1
50D-1
305D-3
300D-3
380D-4
400D-4
70D-1
350D-3
350D-3
75D-1
380D-3
65D-1
220D-3
300D-3
375D-3
300D-3
350D-3
210D-2
190D-2
210D-2
190D-2
230D-235
D-1
165D-2
170D-2
200D-2
165D-2
165D-2
35D-1
185D-2
185D-2
200D-2
200D-2
100D-2
75D-1
320D-3
55D-1
75E-1
75E-1
75E-1
75E-1
75E-1
75E-1
75E-1
75E-1
75E-1
300E-3
300E-3
260E-3
265E-3
40D-1
180D-2
135D-2
285D-3
200D-2
200D-2
100D-1
250D-8
250D-8
R-5
290D-3
240D-3
150D-2
180D-2
200D-2
250D-3
295D-3
165D-2
165D-2
100D-2
400D-3
250D-3
250D-3
100D-2
R-3
R-3
270D-6
270D-6
230D-6
230D-6
R-4 R-4
285D-3
285D-3
285D-3
285D-3
285D-3
285D-3 285
D-3
R-6
285D-3
325D-3325
D-3325D-3
500D-5
500D-5
500D-5
500D-5 500
D-5
500D-5
500D-5
500D-5
500D-5500
D-5
500D-5
500D-5
500D-5
500D-5
500D-5500
D-5
500D-5
500D-5 500
D-5
500D-5
3RD PLACE105
BAPTISTRY146
1 MECHANICAL FLOOR PLANSCALE: 1/8" = 1'-0"
MECHANIC
AL
ROOF P
LAN
DO NOT SCALE DRAWING
M102
THIS
DR
AWIN
G IS C
LASSIFIE
D A
SP
AR
T O
F A
N U
NP
UB
LISHED
COLL
ECTIO
N O
F V
ISUAL
AR
T.
UND
ER
THE 1978
COP
YR
IGHT
ACT, IT IS A
N E
XCLU
SIV
EOR
IGIN
AL
WOR
K O
F A
UTHOR
SHIP
.NONE O
F T
HE P
ICTOR
IAL,
GR
AP
HIC
OR
TECHNIC
AL
CHAR
TS O
R D
RAWIN
GS
DEP
ICTED
ON T
HIS
SHEET M
AY
BE R
EP
ROD
UCED
OR
TR
ANSM
ITTED
IN A
NY F
OR
M O
RB
Y A
NY M
EANS W
ITHOUT T
HE
EXP
RESS P
RIO
R W
RITTEN
PER
MIS
SIO
N O
F T
HE A
RCHITECT.
THIS
PLA
N IS P
ROD
UCED
ONLY
FOR
THIS
PR
OJE
CT O
N T
HIS
SITE
AND
MAY N
OT B
E U
SED
AT
OTHER
LOCATIO
NS.
SHEET T
ITLE
:
OR
IGIN
AL
ISSUE: P
relim
inar
y
SEAL:
REV
DATE
DESCR
IPTIO
N
SHEET NUMBER:
PR
OJE
CT: A
C489
PR
OJE
CT:
BAP
TIS
T C
HUR
CH
SIE
RR
A V
ISTA, AZ
VILLA
GE M
EAD
OWS
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
41 2 3 5 6
DESCR
IPTIO
N
OR
IGIN
AL
ISSUE
Pr
elim
inar
y0
DANIE
L COOK
AR
CHITECT│
290
9 W
ASHIN
GTO
N B
LVD
- O
GD
EN, UT
8440
1│P
H: 80
0-5
52-
7137│
www.B
GWSER
VIC
ES.c
om
SIE
RR
A V
ISTA, AR
IZONA 8
5635
140
7 S E
L CAM
INO R
EAL
PRELIMINARY D
RAWING!
NOT
FOR C
ONSTR
UCTION!
1 PIPE CONDENSATE FULL SIZE TO NEAREST ROOF DRAIN.
KEYED NOTES
NOTE:
1) SPACE ABOVE CEILING IS TO BE USED AS A RETURN AIR PLENUM. ALL MATERIALS TO BE PLENUMRATED.
2) ALL TERMINAL SUPPLY DUCT BRANCHES TO BE EQUIPPED WITH MANUAL BALANCING DAMPER.
3) FLEX DUCT (MAXIMUM 60" LONG) TYPICAL ON EACH DIFFUSER EXCEPT IN EXPOSED APPLICATIONS.
4) PROVIDE TURNING VANES IN ALL RECTANGULAR ELBOWS.�
NOTE:
MECHANICAL CONTRACTOR TO REVIEW ALL DRAWINGS FOR CONFLICTS WITH STRUCTURE AND OTHERTRADES. MECHANICAL CONTRACTOR TO RESOLVE ALL CONFLICTS WITH ENGINEER PRIOR TO ORDERING,FABRICATING OR INSTALLING DUCTWORK.
R1
R2
R5
R4
d d
B.9
14
AC1
AC2
RTU5RTU
3
RTU4
RTU1
RTU6
RTU8
RTU7
RTU2
u u
1
18
187
A A
B B
r r
j
15
15 17
n n
C C
165
5
2
3 9 10 1211
f
l
o o
q
t
6
e
h
4 8 13
p
s
m
k
G
R3
R3
6.1 6.9
h.9
EF4
EF5
EF3
EF2
EF1
EF6
EF9
EF7
EF8
1 MECHANICAL ROOF PLANSCALE: 1/8" = 1'-0"
MECHANIC
AL
DETAILS
DO NOT SCALE DRAWING
M501
THIS
DR
AWIN
G IS C
LASSIFIE
D A
SP
AR
T O
F A
N U
NP
UB
LISHED
COLL
ECTIO
N O
F V
ISUAL
AR
T.
UND
ER
THE 1978
COP
YR
IGHT
ACT, IT IS A
N E
XCLU
SIV
EOR
IGIN
AL
WOR
K O
F A
UTHOR
SHIP
.NONE O
F T
HE P
ICTOR
IAL,
GR
AP
HIC
OR
TECHNIC
AL
CHAR
TS O
R D
RAWIN
GS
DEP
ICTED
ON T
HIS
SHEET M
AY
BE R
EP
ROD
UCED
OR
TR
ANSM
ITTED
IN A
NY F
OR
M O
RB
Y A
NY M
EANS W
ITHOUT T
HE
EXP
RESS P
RIO
R W
RITTEN
PER
MIS
SIO
N O
F T
HE A
RCHITECT.
THIS
PLA
N IS P
ROD
UCED
ONLY
FOR
THIS
PR
OJE
CT O
N T
HIS
SITE
AND
MAY N
OT B
E U
SED
AT
OTHER
LOCATIO
NS.
SHEET T
ITLE
:
OR
IGIN
AL
ISSUE: P
relim
inar
y
SEAL:
REV
DATE
DESCR
IPTIO
N
SHEET NUMBER:
PR
OJE
CT: A
C489
PR
OJE
CT:
BAP
TIS
T C
HUR
CH
SIE
RR
A V
ISTA, AZ
VILLA
GE M
EAD
OWS
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
DESCR
IPTIO
N
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
MM
-DD
-YY
41 2 3 5 6
DESCR
IPTIO
N
OR
IGIN
AL
ISSUE
Pr
elim
inar
y0
DANIE
L COOK
AR
CHITECT│
290
9 W
ASHIN
GTO
N B
LVD
- O
GD
EN, UT
8440
1│P
H: 80
0-5
52-
7137│
www.B
GWSER
VIC
ES.c
om
SIE
RR
A V
ISTA, AR
IZONA 8
5635
140
7 S E
L CAM
INO R
EAL
PRELIMINARY D
RAWING!
NOT
FOR C
ONSTR
UCTION!
COORDINATE DIFFUSER TYPE FORLAY-IN OR GYPSUM BOARD CEILING.
SUPPORT FLEX DUCT FROMSTRUCTURE ABOVE. ONE 1" X 22 GA
STRAP
FLEX DUCT SEE DRAWINGS FOR SIZE
MAKE BEND RADIUS 1-1/2 xDUCT RADIUS
NOTE:RETURN SIMILAR BUT WITHOUT DUCT
TIGHTENING BAND
CEILING MATERIAL
5 FT. MAXIMUM.MAX. SAG 1/2" PER FOOT OF SUPPORTSPACING.
SUPPORT FLEX DUCT FROMSTRUCTURE ABOVE. ONE 1" X 22 GASTRAP
METAL FASTENERS :OMARK INSUL-PINS, DURA DYNE FASTENERS OR GRIP NAILS.GRIP NAILS SHALL BE INSTALLED BY "GRIP NAIL AIR HAMMER"OR BY AUTOMATIC FASTENER EQUIP.
LINER TO BE ADHERED TO DUCT WITH 90%MIN. AREA COVERAGE OF ADHESIVE
ALL ENDS OF LINER TO BE COATED WITH ADHESIVE. ENDS OF LINERSHALL BE BUTTED FIRMLY TOGETHER AND TAPED OVER.
LAPPED & BUTTEDCORNERS
DUCT LINER (SEE SPEC. FORTHICKNESS)
TOP AND BOTTOM SECTION OF LINERSHALL OVERLAP THE SIDESDUCT LINER SEE SPEC FOR
THICKNESS
METAL FASTENERS 12" O.C. MAX. FORBELOW 2500 FPM VELOCITY
NOT MORE THAN 2" FROMEDGE OF LINER
THE VELOCITY RATED SIDE OF LINER MUSTFACE THE AIR FLOW
GALV. SHT.METAL DUCT
HHDRIVE
SLIP
AT JOINTS
2424
2224
2624
PLAINS SLIP
RECOMMENDEDGA.
2624
HEMMEDS SLIP
24
24242422
REIN-FORCEDBAR SLIP
MIN.H.
11
11
2624
2224
NONE REQUIREDNONE REQUIRED
1" X 1" X 1/8" @ 60 IN1" X 1" X 1/8" @ 60 IN
IN.
TRANSVERSE REINFORCING (1)
13 - 18
31 - 4219 - 30
UP THRU 12
ALTER'NTBAR SLIP
SHEETMETAL GA.(ALL FOUR
SIDES)
DIMENSION OF LONGESTSIDE. INCHES
MINIMUM REINFORCING ANGLESIZE AND MAXIMUM LONGITUDINALSPACING BETWEEN TRANSVERSE
JOINT & /OR INTERMEDIATEREINFORCING
(1) TRANSVERSE REINFORCING SIZE IS DETERMINED BYDIMENSION OF SIDE TO WHICH ANGLE IS APPLIED.
RECOMMENDEDGA.
RECOMMENDEDGA.
RECOMMENDEDGA.
W1
W2
1. ALL VANED ELBOWS SHALL BE CONSTRUCTED AND INSTALLED AS DETAILED BYSMACNA.
2. WHEN W1 DOES NOT EQUAL W2, VANE SHALL BE SINGLE VANE TYPEREGARDLESS OF 'W' DIMENSION. ALL SINGLE VANES SHALL HAVE A 2 INCHRADIUS, 1 INCH MAXIMUM.
3. SPACE BETWEEN VANES AND A 3/4 INCH TRAILING EDGE.4. WHEN W1 EQUALS W2 AND W1 IS GREATER THAN 20 INCHES, VANE SHALL BE
DOUBLE VANE TYPE.
TURNING VANES
12" MIN
ROOF MOUNTED EXHAUST FAN WITHBIRD SCREEN
ANCHOR CURB TOHOOD
CANT STRIP
BUILT-UP ROOFING
INSULATIONEXHAUST DUCT SEEDRAWINGS FOR SIZE
GRAVITY BACKDRAFT DAMPER
FRAMING ALL AROUND
ROOF CURB
FLASH AND COUNTERFLASH
1/4" SPONGE RUBBER GASKET ALLAROUND
SUPPORT ANGLE FOR DAMPERATTACHED TO CURB
UNION
TRUSS JOIST
DRAIN CONNECTIONFLUE OUTLET
ECONOMIZER AS SPECIFIED
GAS PIPING. RUN 6" MIN. ABOVE ROOF
SHUT OFF COCK
DIRT LEG
ROOF INSULATION
SEE PLANS FOR SIZE
RETURN AIRLAY IN CEILING
SUPPLY AIR
MAKE TRANSITIONS AS SHOWN ON DRAWINGS TOCONNECT TO DUCTWORK
PROVIDE FLEX CONNECTIONS AT UNIT
ROOF CURB
ELECTRICDISCONNECT
ROOFTOP UNIT
PROVIDE 3" OF ACOUSTICAL INSULATION BELOW THEENTIRE FAN SECTION OF UNIT. SEAL W/ RUBBER CAULKING
TO PREVENT SOUND TRANSFER THROUGH DECK.
TRUSS JOIST
FLUE OUTLET
ECONOMIZER AS SPECIFIED
GAS PIPING, RUN 6" MIN. ABOVE ROOF
SHUT OFF COCK
DIRT LEGROOF INSULATION
SEE PLANS FOR SIZE
LAY IN CEILINGRETURN AIR
SUPPLY AIR
MAKE TRANSITIONS AS SHOWN ON DRAWINGS TOCONNECT TO DUCTWORK PROVIDE FLEX CONNECTION
AT UNIT
ROOF CURB
ROOFTOP UNIT
ELECTRIC DISCONNECT
DRAIN CONNECTIONPROVIDE 3" OF ACOUSTICAL INSULATION BELOW THE
ENTIRE FAN SECTION OF UNIT. SEAL W/ RUBBER CAULKINGTO PREVENT SOUND TRANSFER THROUGH DECK.
UNION
DUCT
1-1/2" POCKET SLIP
NEOPRENE COATED FABRICBOLT ON 4" CENTER
1" FLANGE & HEM
NOTES:1. A VERTICAL DAMPER IS SHOWN. HORIZONTAL DAMPER INSTALLATION IS SIMILAR. FOLLOW DAMPER MANUFACTURERSINSTRUCTIONS, INCLUDING FASTENER OPTIONS AND GAGES FOR SLEEVE AND PERIMETER ANGLES. FIRE DAMPERS MUSTBE INSTALLED IN THE PARTITION OR FLOOR, NOT OUTSIDE THE PENETRATION.
2. GALVANIZED SLEEVE: GAGE NOT LESS THAN CONNECTING DUCT. FASTEN SLEEVE TO DAMPER FRAME AND TO PERIMETERANGLES.
3. PERIMETER ANGLES: GALVANIZED STEEL, NOT LESS THAN 1-1/2"x1-1/2", 14 GAGE, TO PROVIDE 1" MINIMUM OVERLAP OFOPENING ON ALL 4 SIDES.
4. BREAKAWAY DUCT CONNECTION: CONTRACTORS OPTION OF TYPES SHOWN IN SMACNA LPDS, FIG. 2-13. SEAL JOINTS.
5. ACCESS PANELS: SIZE AND LOCATION TO PERMIT SERVICING THE FUSIBLE LINK OR LINKS.
6. PROVIDE A CLEARANCE FOR DAMPER SLEEVE WITHIN WALL OPENING OF 1/8" PER FOOT OF WIDTH (OR HEIGHT), OR PERMANUFACTURER'S INSTALLATION INSTRUCTIONS. THE SLEEVE MAY REST ON BOTTOM OF OPENING, AND NEED NOT BECENTERED.
7. ALL DUCT WORK RISERS WHICH ARE RUN EXPOSED, SUCH AS THRU ATTIC FLOORS AND MECANICAL ROOM FLOORS,SHALL BE PROVIDED WITH A 3" HIGH CONCRETE CURB AROUND OPENING FOR DUCT.
PERIMETER ANGLE, NOTE 3 (NOT FASTENED TOPARTITION)
SLEEVE, NOTE 2
DUCT CONNECTION NOTE 4
DAMPER COLLAR EXTENSIONINTEGRAL PART OF SLEEVE
SLEEVE, NOTE 2NOTE 6
FIRE BARRIER PARTITION ORCHASE
TYPICAL DUCT INSULATION
AP NOTE 5
FAN CONTACTOR
24V COIL
RED
BLACK
IONIZATIONUNIT
IN UNIT SUPPLYPLENUM
1 DIFFUSER CONNECTIONSCALE: N.T.S. 2 DUCT LINER
SCALE: N.T.S.
3 DUCT CONSTRUCTION DETAILSCALE: N.T.S. 4 SQUARE VANED ELBOWS
SCALE: N.T.S.
5 ROOF MOUNT EXHAUST FANSCALE: N.T.S.
6 ROOFTOP UNIT (GAS)SCALE: N.T.S.
7 ROOFTOP UNIT (GAS-SIDE DISCHARGE)SCALE: N.T.S. 8 FLEX CONNECTION
SCALE: N.T.S.
9 FIRE DAMPERSCALE: N.T.S. 10 ION GENERATOR WIRING DIAGRAM
SCALE: N.T.S.
