HDS Gen3: 4 -...

HDS Gen3: 4.04.0-55.1.74

HDS Gen2 Touch: 6.06.0-54.2.46

Software Updates

HDS Gen3

New Features

New Features• HDS Gen3 Features With Version 4.0

– Mercury VesselView – VesselView Link Support– Enabled C-MAP Easy Routing and Navionics Autorouting in

the U.S.A.• Previously unavailable on units sold in the U.S.A or on units used in

the U.S. or in U.S. Territorial waters.

– Network Analyzer and Service Assistant Improvements

3 © Navico Company Confidential

HDS Gen2 Touch

New Features

New Features• HDS Gen2 Touch Features With Version 6.0

– Mercury VesselView – VesselView Link Support– Enabled C-MAP Easy Routing and Navionics Autorouting in

the U.S.A.• Previously unavailable on units sold in the U.S.A or on units used in

the U.S. or in U.S. Territorial waters.


HDS Gen3 and Gen2 Touch

Mercury VesselView Link

VesselView Link Support

Brand new user interface• Split screen functionality• Brand new control bar• Touch Friendly user interface• Scalable for different split ratios

NOS 55 will introduce support for the brand new Mercury Marine VesselView Link SmartCraft gateway.

Brand New Interface

• Display the most relevant engine information– RPM– Speed– Fuel level– Voltage– Engine trim – Trim tabs

• Quick access to engine data• Deep dive for enlarged view• Engine fault notifications• Fault notification identifying effected engine

The new Mercury user interface is packed full of features and has been developed by extensive end user testing and feedback. The new user interface is designed to:

Deep dive Panels

Split Screen FunctionalityAdd the Mercury panel to any split screen combination

Quick Access Control Bar

Quick access to:

• SmartCraft engine data• Cruise control• Troll control• Smart Tow• Eco Mode

Quick Access to Engine Data

Engine Control While Fishing

Easily enable and adjust Troll and Cruise Control from ANY panel.

Fault Warnings & History

Engine warning and fault notificationsAlarm history for all engine faults

Engine MaintenanceEngine maintenance life remaining & Reset

Compatible MFD’s

• HDS gen2 Touch• HDS gen3

Interfacing

VesselView Link module is powered from the Smartcraft network

VesselView Link Single Mercury P/N:8M0110639

InterfacingVesselView Link Multi Mercury P/N:8M0110641

HDS Gen3 and Gen2 Touch

C-MAP Easy RoutingNavionics Autorouting– Now available in the U.S.A

Jeppesen CMAP MAX-N+

© Navico Company Confidential20

• Easy Routing – Automatically create a route– Automatically calculates the shortest safe route based upon user selected start and

end points. • Calculations based upon vessel settings (Draught, Beam Width, Height) and chart data to determine safe

route legs.– Green Route Leg = Safe– Yellow Route Leg = Potentially Dangerous– Red Route Leg = Potentially Unsafe (Recreate the route selecting different start/end points)

Jeppesen CMAP MAX-N+


• Dynamic Tides and Currents– Dynamic Tides and Currents give a graphical representation of the current

activity when the chart is zoomed in beyond a 1mi. zoom scale. • Standard Current icons are replaced by color coded arrows indicating the direction

and speed of the current. • Selecting a current arrow on screen will open the modified currents page in the unit.

– With Dynamic Tides and Currents we show when currents are Ebb or Flood

Navionics Autorouting


• Autorouting– Automatically calculate the shortest, safe route based on chart data and vessel

settings– Compatible with Navionics Platinum, Navionics+ and Navionics Updates Cards

HDS Gen3

Network Analyzer & Service Assistant Upgrades

Network Analyzer and Service Assistant Upgrades

• Expands on the number of connected devices compatible with the Network Analyzer feature.– Network Analyzer (Remote Software Updates): Allows a connected

device to scan the boats network of devices and check to see if each device’s software is up to date. With this update we can check for more devices and offer to download updates directly to an installed blank SD/microSD card.


Noteworthy Bug Fixes and Improvements

Fixes• Fusion AV750 (Gen3): We have corrected an issue

when connecting to a Fusion AV750 radio via Fusion-Link and losing the ability to power the radio on/off

• Trails (Gen2T & Gen3): We have corrected an issue with trails not remaining if they were created on an older version of software, then imported into HDS Gen2 Touch and Gen3. See Tech Bulletin TB-82258 (In Appendix) for full details of the issue – The workaround described in TB-82258 is no longer

required


Appendix

TB-82258 / June 15, 2016HDS Gen3 (SW version 3.5) and HDS Gen2 touch (SW version 5.5) trail persistence issue Product: All SKU’sProduct Description: HDS Gen2 Touch & HDS Gen3Software Version: HDS G2T – 5.5 & HDS Gen3 – 3.5Effective Date: 26 June 2016Inspect/Update Current Inventory: No

HDS users importing Waypoints, Routes & Trails (WRT) saved from a previous software version may experience an issue with trails disappearing from their HDS unit after the unit is powered off. This will be corrected in an upcoming software update, but in the interim, a workaround is available that addresses this issue. Users not re-importing or replacing their WRT file after the software update to 3.5 (Gen3) or 5.5 (Gen2 Touch) should not have issues with existing trail dataUsers saving WRT files in 3.5 or 5.5 also should not have issues with trail persistence when data is imported

How to Back up Waypoints, Routes & Trails:Press the Pages keySelect FilesSelect Waypoints, Routes, Trails and Trips database Select ExportSelect User data file version 5Select Export Select the desired memory card destination (Left or Right)Press OK Select New or if there are no other WRT files on the card. (Change the file Name, if desired)Select Enter.

Executing the Workaround:If the WRT file was exported from software version 3.0 (Gen3), 5.0 (Gen2 Touch) or earlier, you will need to perform the workaround.

Insert the SD or microSD card containing the Exported/Saved WRT file into the card slot Import the WRT file from the SD/microSD card to an HDS unit running software version 3.5 (Gen3) or 5.5 (Gen2 Touch)Before attempting to power off or reboot the HDS unit, re-export the WRT file from the HDS unit running software version 3.5 (Gen3) or 5.5 (Gen2 Touch)Follow the steps above for exporting a WRT file.

Power Cycle the UnitRe-import the WRT file created on the HDS unit with software version 3.5 (Gen3) or 5.5 (Gen2 Touch).Follow the steps above to Import the WRT file.


HDS Gen3: 4 -...

Documents

Transcript of HDS Gen3: 4 -...