Ccc Centrifugal Compressor control

download Ccc Centrifugal Compressor control

of 100

  • date post

    23-Oct-2014
  • Category

    Documents

  • view

    485
  • download

    36

Embed Size (px)

Transcript of Ccc Centrifugal Compressor control

PID A/D

UF

RAM

GLOBAL SUPPLIERS OF TURBINE

ID

AND COMPRESSOR CONTROL SYSTEMS

UM5513

Series 3 Plus Engineering Utilitiesuser manual

TrainTools Series 3 Plus Engineering UtilitiesCongurator and Fast RecorderPublication UM5513 (1.1.0)Product Version: 3.1 October 2004

4725 121st Street Des Moines, Iowa 50323, U.S.A. Phone: (515) 270-0857 Fax: (515) 270-1331 Web: www.cccglobal.com

Documented Program Versions: S3p_OPC.exe s3config.exeRec5.exe ScanVer.exe 3.1 2.4 3.1 2.6

2000-2004, Compressor Controls Corporation. All rights reserved. This manual is for the use of Compressor Controls Corporation and is not to be reproduced without written permission. Air Miser, Guardian, Recycle Trip, Reliant, Safety On, SureLink, TTC, Total Train Control, TrainTools, TrainView, TrainWare, Vanguard, Vantage, WOIS, and the TTC and impeller logos are registered trademarks; and COMMAND, TrainPanel, and the Series 5 logo are trademarks of Compressor Controls Corporation. Other company and product names used herein are trademarks or registered trademarks of their respective holders. The control methods and products discussed in this manual may be covered by one or more of the following patents, which have been granted to Compressor Controls Corporation by the United States Patent and Trademark Office: 4,949,276 5,622,042 5,879,133 6,116,258 6,494,672 5,347,467 5,699,267 5,908,462 6,217,288 6,503,048 5,508,943 5,743,715 5,951,240 6,317,655 5,609,465 5,752,378 5,967,742 6,332,336

Many of these methods have also been patented in other countries, and additional patent applications are pending. The purpose of this manual is only to describe the configuration and use of the described products. It is not sufficiently detailed to enable outside parties to duplicate or simulate their operation. The completeness and accuracy of this document is not guaranteed, and nothing herein should be construed as a warranty or guarantee, expressed or implied, regarding the use or applicability of the described products. CCC reserves the right to alter the designs or specifications of its products at any time and without notice.

TrainTools Series 3 Plus Engineering Utilities

3

Document ScopeThis manual describes the installation and operation of the TrainTools Series 3 Plus Engineering Utilities for Series 3 and Series 3 Plus Controllers: Chapter 1 Chapter 2 Chapter 3 Chapter 4 Appendix A Appendix B introduces the Series 3 Plus Engineering Utilities and briefly describes each of its component programs. describes the default operation of the Series 3 Plus OPC Server. tells how to load and configure controller application software using the Configurator utility. tells how to use the Fast Recorder program to record and display operating data from the Series 3 Plus OPC server. tells how to install, maintain, and remove the Series 3 Plus Engineering Utilities software package. tells how to physically interconnect controller and PC serial ports.

Additional information on using the Series 3 Plus OPC Server in a multi-workstation environment can be found in the Series 3 Plus OPC Server user manual [UM5503]. Detailed information on the configuration and operation of each Series 3 Plus Controller can be found in the following instruction manuals: IM301 IM302 IM303 IM307 IM308 IM311 IM312 IM313

Antisurge Controller for Axial and Centrifugal Compressors Performance Controller for Axial and Centrifugal Compressors Dual-Loop A/P Controller for Axial and Centrifugal Compressors Speed Controller for Steam Turbines Extraction Controller for Steam Turbines Fuel Controller for Multishaft Industrial Gas Turbines Fuel Controller for Aero-Derivative Multishaft Gas Turbines Fuel Controller for Single-Shaft Gas Turbines

Additional information relating to TrainTools software can be found in the following document, which is included at the back of printed copies of this manual: MS79 Software License Agreement

UM5513 (1.1.0)

4

Contents

Document ConventionsThe document title appears in the header of each odd-numbered page, while the chapter or appendix title appears in the header of even-numbered pages. Odd-page footers list the document number and revision level [UM5513 (1.1.0)], while even-page footers provide the publication date (October 2004). Acronyms are defined in the sections of this manual that discuss the corresponding subjects, by placing them in parentheses following the spelled-out terms they represent. As an example, a three-letter acronym (TLA) is a way to represent a three-word subject by combining and capitalizing the initial letters of those three words. Most are also listed under Symbols and Acronyms on page 10. Cross-references to other documents specify a section and chapter, while cross-references between chapters of this document specify a page number. References that do not specify a location are internal to the chapter in which they appear. In computerized versions of this manual, all such references are hot-linked to their target locations and appear in green. Entries in the tables of contents, illustration and table lists, and index are also hot-linked but are not green. Attention may be drawn to information of special importance by using this text styling or one of the following structures:

Note: Caution: Warning!

Notes contain important information that needs to be emphasized. Cautions contain instructions that, if not followed, could lead to irreversible damage to equipment or loss of data. Warnings contain instructions that, if not followed, could lead to personal injury. The appearance of this electrical hazard warning symbol on CCC equipment or the word Warning appearing in this manual indicates dangerously-high voltages are present inside its enclosure. To reduce the risk of fire or electrical shock, do not open the enclosure or attempt to access areas where you are not instructed to do so. Refer all servicing to qualified service personnel. The appearance of this user caution symbol on CCC equipment or the word Caution appearing in this manual indicates damage to the equipment or injury to the operator could occur if operational procedures are not followed. To reduce such risks, follow all procedures or steps as instructed.

October 2004

TrainTools Series 3 Plus Engineering Utilities

5

Table of ContentsDocument Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . List of Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symbols and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 5 8 8 9

Chapter 1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Purpose and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 3 Plus OPC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 3 Plus Configurator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fast Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 12 13 14 15 15 17 18 20 20 21 21 22 23 23 24 24 24 25 25 25 26

Chapter 2

Series 3 Plus OPC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Default Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Server Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Default Tag Sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Server Log File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Server Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adding Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EUType Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modbus Register Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modbus Identity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modbus Access Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baud Rate and Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Port Activity Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communication Error Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . .

UM5513 (1.1.0)

6

Contents

Chapter 3

Series 3 Plus Configurator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Closing Configurator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Program Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Configurator Preferences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Scanning for Controller