CAVA CURVE LED PENDANT DIRECT … in accordance with IESNA LM-79, unless otherwise indicated....
Transcript of CAVA CURVE LED PENDANT DIRECT … in accordance with IESNA LM-79, unless otherwise indicated....
CAVA CURVE LED PENDANT DIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.CURVE.PENDANT.DIRECT.SPEC February 19, 2015 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
ORDER GUIDE
CROSS SECTION
2 1/2"
2"
4 1/2"
4 1/2"
2 1/2"
2"
4 1/2"
4 1/2"
CAVCPD - air craft cable CAVCPD - stem
See page 2 for ordering code detailed information
PROJECT: __________________________________
____________________________________________
TYPE: ______________________________________
NOTES: ____________________________________
____________________________________________
CAVCPD RLO LED
LUMINAIRE ID END CAP OPTICS LIGHT SOURCE CRI LUMEN PACKAGES COLOR TEMP.
CAVCPD - cava curve pendant direct OP - open end cap
CO - closed end cap
RLO - Reduced Luminance Optic LED - high performance LED 80 - 80CRI
90 - 90CRI (consult factory)
350 - low output 350lm/f
500 - medium output 500lm/f
750 - high output 750lm/f
30 - 3000k
35 - 3500k
40 - 4000k
LUMINAIRE LENGTH VOLTAGE DRIVER ELECTRICAL MOUNTING FINISH CONTROLS
Standard sections - 2', 3', 4', 5', 8' & 12'
For all other specify length
#FT - nominal length in feet
Continuous Run - for luminaires over 12'
120 - 120V
277 - 277V
UNV - 120V-277V
347 - 347V
D - dimming 0-10V
DA - Dali
LHL# - Lutron Hi-Lume A
LEH - Lutron EcoSystem H
LE5 - Lutron EcoSystem 5
OTH - other (consult factory)
1 - 1 circuit
+#EB - emergency battery pack
(for min 4' fixture)
+#EM - emergency light circuit
+#NL - night light circuit
+GTD - generator transfer device
53WAC36 - power 5" + non power
3" white canopy (36" air craft cable)
55WSW18 - power 5" + non power
5" white canopy & stem (18" stem)
For all other mountings refer to the
Pendant Mounting Guide.
W - matte white
AL - aluminum
CF# - custom finish specify RAL#
ONBOARD
OMS - Motion Sensor & power pack
ODS - Daylight Sensor & controller
WIRELESS
EWC - EnOcean Wireless Controller
LMC - Lutron Motion Controller
LDC - Daylight Controller
OPTIONS
FU - fuse
TB# - T-bar caddy clip specify grid size
TG# - Tegular caddy clip specify grid size
ST - Screw Slots caddy clip
CU - custom
Shown with a open end cap Shown with an closed end cap
DESCRIPTIONCava is a linear LED pendant
luminaire with a remarkably comfortable and
surprising appearance. Using completely
concealed and indirect LED arrays, Cava
provides superior brightness control, while
maintaining high efficacy by distributing light
over the vaulted interior cavity of the luminaire.
Cava offers totally direct or segmented
direct/indirect distributions. See separate spec
sheets for other available design.
up to 111 lm/w performance
CAVA CURVE LED PENDANT DIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.CURVE.PENDANT.DIRECT.SPEC February 19, 2015 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
OPTICSREDUCED LUMINANCE OPTIC (RLO) - reduced Luminance Optic (RLO) consists of indirect-
mounted LED arrays illuminating a vaulted reflector with a matte white finish greater than 95%
reflectivity. The ultra-shallow arrays in RLO completely conceal the light source while evenly
distributing brightness over the entire surface of the cavity using a combination of multiple
reflective bounces and a very high diffuse reflectivity. Compared to diffusing optics, RLO reduces
luminaire brightness due to the visible interior surface being larger than the aperture.
LIGHT SOURCE - LEDCustom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
presented in accordance with IESNA LM-79, unless otherwise indicated.
PERFORMANCE PER 4' AT 4000K
LED output Color Temp Watts Nominal Lumens Efficacy Lumens Per Watt
low output 4000K 13 1400 111
medium output 4000K 19 2000 108
high output 4000K 28 3000 107
LUMINAIRE LENGTH
Cava is made up of standard 2, 3, 4, 5, 8 and 12 foot sections
that may be joined together to create longer continuous
run lengths. Nominal run length must be noted in the
product code. The minimum individual section available is
2 foot.
All individual sections are joined together onsite using the
joiner kits provided. LumenWerx offers joiner kits that are
extremely simple to work with in the field and result in a
fixture that appears virtually seamless with no light leak at
any connection.
joining system for Cava curved
ELECTRICAL Factory-set adjustable output current electronic driver with 120-277V AC line input.
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
and DALI protocol drivers.
EMERGENCYFactory installed long life high temperature recyclable Ni-Cad battery pack with test
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
(25ºC) emergency lighting output. Recharge time of 24 hours.
MOUNTING OPTIONSFixtures can be pendant-mounted, using air craft cables, or stem-mounted.
Unless otherwise specified, LumenWerx provides the following hardware:
For cable-mounted fixtures - 53WAC36 (5" white canopy for all power mounting
point, 3" white canopy for non power mounting point, and a 36" cable)
For stem mounted fixtures - 55WSW18 (5" white canopy for all power mounting
point, and non power mounting point, and a 18" white stem)
Caddy clips, if required specify under OPTIONSFor all other required mountings options, for all our Pendant Mounting Guide at
www.lumenwerx.com
FINISHInterior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
CONTROLSLumenWerx offers several options for integrating motion and daylight controls into
Cava luminaires. Wireless options incorporate a wireless controller/powerpack into
the luminaire, which receives signals from a wireless sensor (by others) installed in
the space. The advantages of the wireless option include greater flexibility of control
options, sensor coverage, and system integration. Onboard options incorporate both
the sensor and controller/powerpack. Onboard sensors, while inherently simpler,
have limitations of control and coverage.
CAVA CURVE LED PENDANT DIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.CURVE.PENDANT.DIRECT.SPEC February 19, 2015 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WARRANTYLumenWerx provides a five-year limited warranty of electrical and mechanical
performance of the luminaires, including the LED boards, drivers, and auxiliary
electronics. LumenWerx will repair or replace defective luminaires or components at
our discretion, provided they have been installed and operated in accordance with our
specifications. Other limitations apply, please refer to the full warranty on our website.
OnboardOnboard Motion Sensor and power pack (OMS) provide automatic on and automatic off control,
using PIR detection. Sensor is designed to detect fine-motion when installed within 6' of occupants.
Onboard Daylight Sensor and controller (ODS) provide input for 0-10V dimming drivers. Separate
switched control of line input is required for on/off control.
2.5"
Location of an Onboard sensor
WirelessEnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTIONHousing - Extruded Aluminum 0.075" nominal, matte white or silver powder coating.
Custom finishes are also available.
End cap - Die cast Aluminum (0.95" nominal)
Joiners - Die cast Aluminum (0.95" nominal)
Reflectors - Extruded Aluminum 0.07" nominal, 95% reflective matte white painted
Hanger - Chromed Griplock securely attached with spring steel hardware in end caps and/or
joiners
Air craft cable suspension - 7x7 braids Aluminum air craft cable 0.06" thick
Stem - 0.5" diameter threaded steel tube matte white or silver powder coating. Custom finishes are
also available
WEIGHTCava curved 4ft - 11.78lbs - 5.35kg
Cava curved 8ft - 22.91lbs - 10.4kg
Cava curved 12ft - 34.14lbs - 15.5kg
CERTIFICATIONSETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to CAN/CSA
Standard C22.2 No. 250.0.
CAVA CURVE LED PENDANT DIRECT/INDIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.CURVE.PENDANT.DIRECT-INDIRECT.SPEC February 20, 2015 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
ORDER GUIDE
CROSS SECTION
2 1/2"
2"
4 1/2"
4 1/2"
2 1/2"
2"
4 1/2"
4 1/2"
CAVCPDI - air craft cable CAVCPDI - stem
See page 2 for ordering code detailed information
PROJECT: __________________________________
____________________________________________
TYPE: ______________________________________
NOTES: ____________________________________
____________________________________________
CAVCPDI RLO LED
LUMINAIRE ID END CAP OPTICS LIGHT SOURCE CRI DIRECT LUMEN PACKAGES INDIRECT LUMEN PACKAGES COLOR TEMP.
CAVCPDI - cava curve
pendant direct indirect
OP - open end cap
CO - closed end cap
RLO - Reduced Luminance Optic LED - high performance LED 80 - 80CRI
90 - 90CRI (consult factory)
350 - low output 350lm/f
500 - medium output 500lm/f
750 - high output 750lm/f
500 - low output 500lm/f
750 - medium output 750lm/f
30 - 3000k
35 - 3500k
40 - 4000k
LUMINAIRE LENGTH VOLTAGE DRIVER ELECTRICAL MOUNTING FINISH CONTROLS
Standard sections - 2', 3', 4', 5', 8' & 12'
For all other specify length
#FT - nominal length in feet
Continuous Run - for luminaires over 12'
120 - 120V
277 - 277V
UNV - 120V-277V
347 - 347V
D - dimming 0-10V
DA - Dali
LHL# - Lutron Hi-Lume A
LEH - Lutron EcoSystem H
LE5 - Lutron EcoSystem 5
OTH - other (consult factory)
1 - 1 circuit
2 - 2 circuits
+#EB - emergency battery pack
(for min 4' fixture)
+#EM - emergency light circuit
+#NL - night light circuit
+GTD - generator transfer device
53WAC36 - power 5" + non power
3" white canopy (36" air craft cable)
55WSW18 - power 5" + non power
5" white canopy & stem (18" stem)
For all other mountings refer to the
Pendant Mounting Guide.
W - matte white
AL - aluminum
CF# - custom finish specify RAL#
ONBOARD
OMS - Motion Sensor & power pack
ODS - Daylight Sensor & controller
WIRELESS
EWC - EnOcean Wireless Controller
LMC - Lutron Motion Controller
LDC - Daylight Controller
OPTIONS
FU - fuse
DC - dust cover
TB# - T-bar caddy clip specify grid size
TG# - Tegular caddy clip specify grid size
ST - Screw Slots caddy clip
CU - custom
Shown with a open end cap Shown with an closed end cap
DESCRIPTIONCava is a linear LED pendant
luminaire with a remarkably comfortable and
surprising appearance. Using completely
concealed and indirect LED arrays, Cava
provides superior brightness control, while
maintaining high efficacy by distributing light
over the vaulted interior cavity of the luminaire.
Cava offers totally direct or segmented
direct/indirect distributions. See separate spec
sheets for other available design.
up to 106 lm/w performance
CAVA CURVE LED PENDANT DIRECT/INDIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.CURVE.PENDANT.DIRECT-INDIRECT.SPEC February 20, 2015 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
OPTICSREDUCED LUMINANCE OPTIC (RLO) - reduced Luminance Optic (RLO) consists of indirect-
mounted LED arrays illuminating a vaulted reflector with a matte white finish greater than 95%
reflectivity. The ultra-shallow arrays in RLO completely conceal the light source while evenly
distributing brightness over the entire surface of the cavity using a combination of multiple
reflective bounces and a very high diffuse reflectivity. Compared to diffusing optics, RLO reduces
luminaire brightness due to the visible interior surface being larger than the aperture.
LIGHT SOURCE - LEDCustom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
presented in accordance with IESNA LM-79, unless otherwise indicated.
PERFORMANCE PER 4' AT 4000KHigh Indirect Output (3000 Lumens)
LED output Color Temp
Watts Direct
Lumens
Indirect
Lumens
Total Nominal Lumens
Efficacy Lumens Per Watt
low output 4000K 42 1400 3000 4400 104
medium output 4000K 48 2000 3000 5000 104
high output 4000K 58 3000 3000 6000 104
Low Indirect Output (2000 Lumens)
LED output Color Temp
Watts Direct
Lumens
Indirect
Lumens
Total Nominal Lumens
Efficacy Lumens Per Watt
low output 4000K 32 1400 2000 3400 106
medium output 4000K 38 2000 2000 4000 105
high output 4000K 48 3000 2000 5000 105
LUMINAIRE LENGTH
Cava is made up of standard 2, 3, 4, 5, 8 and 12 foot
sections that may be joined together to create
longer continuous run lengths. Nominal run length
must be noted in the product code. The minimum
individual section available is 2 foot.
All individual sections are joined together onsite
using the joiner kits provided. LumenWerx offers
joiner kits that are extremely simple to work with in
the field and result in a fixture that appears virtually
seamless with no light leak at any connection.
joining system for Cava curved
ELECTRICAL Factory-set adjustable output current electronic driver with 120-277V AC line input.
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
and DALI protocol drivers.
EMERGENCYFactory installed long life high temperature recyclable Ni-Cad battery pack with test
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
(25ºC) emergency lighting output. Recharge time of 24 hours.
CAVA CURVE LED PENDANT DIRECT/INDIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.CURVE.PENDANT.DIRECT-INDIRECT.SPEC February 20, 2015 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
CONSTRUCTIONHousing - Extruded Aluminum 0.075" nominal, matte white or silver powder coating.
Custom finishes are also available.
End cap - Die cast Aluminum (0.95" nominal)
Joiners - Die cast Aluminum (0.95" nominal)
Reflectors - Extruded Aluminum 0.07" nominal, 95% reflective matte white painted
Hanger - Chromed Griplock securely attached with spring steel hardware in end caps
and/or joiners
Air craft cable suspension - 7x7 braids Aluminum air craft cable 0.06" thick
Stem - 0.5" diameter threaded steel tube matte white or silver powder coating.
Custom finishes are also available
WEIGHTCava curved 4ft - 11.78lbs - 5.35kg
Cava curved 8ft - 22.91lbs - 10.4kg
Cava curved 12ft - 34.14lbs - 15.5kg
CERTIFICATIONSETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to
CAN/CSA Standard C22.2 No. 250.0.
WARRANTYLumenWerx provides a five-year limited warranty of electrical and mechanical
performance of the luminaires, including the LED boards, drivers, and auxiliary
electronics. LumenWerx will repair or replace defective luminaires or components at
our discretion, provided they have been installed and operated in accordance with our
specifications. Other limitations apply, please refer to the full warranty on our website.
MOUNTING OPTIONSFixtures can be pendant-mounted, using air craft cables, or stem-mounted.
Unless otherwise specified, LumenWerx provides the following hardware:
For cable-mounted fixtures - 53WAC36 (5" white canopy for all power mounting point, 3" white
canopy for non power mounting point, and a 36" cable)
For stem mounted fixtures - 55WSW18 (5" white canopy for all power mounting point, and non
power mounting point, and a 18" white stem)
Caddy clips, if required specify under OPTIONSFor all other required mountings options, for all our Pendant Mounting Guide at
www.lumenwerx.com
FINISHInterior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
CONTROLSLumenWerx offers several options for integrating motion and daylight controls into Cava
luminaires. Wireless options incorporate a wireless controller/powerpack into the luminaire,
which receives signals from a wireless sensor (by others) installed in the space. The advantages
of the wireless option include greater flexibility of control options, sensor coverage and system
integration. Onboard options incorporate both the sensor and controller/powerpack. Onboard
sensors, while inherently simpler, have limitations of control and coverage.
OnboardOnboard Motion Sensor and power pack (OMS) provide automatic on and automatic off control,
using PIR detection. Sensor is designed to detect fine-motion when installed within 6' of occupants.
Onboard Daylight Sensor and controller (ODS) provide input for 0-10V dimming drivers. Separate
switched control of line input is required for on/off control.
2.5"
Location of an Onboard sensor
WirelessEnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CAVA LED RECESSED W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.RECESSED.SPEC February 19, 2015 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
ORDER GUIDE
CROSS SECTION
4 1/2"
4 1/2"
2 1/2"
CAVR - cava recessed
See page 2 for ordering code detailed information
PROJECT: __________________________________
____________________________________________
TYPE: ______________________________________
NOTES: ____________________________________
____________________________________________
CAVR RLO LED
LUMINAIRE ID OPTICS LIGHT SOURCE CRI LUMEN PACKAGES COLOR TEMP. LUMINAIRE LENGTH
CAVR - cava recessed RLO - Reduced Luminance Optic LED - high performance LED 80 - 80CRI
90 - 90CRI (consult factory)
350 - low output 350lm/f
500 - medium output 500lm/f
750 - high output 750lm/f
30 - 3000k
35 - 3500k
40 - 4000k
Standard sections - 2', 3', 4', 5', 8' & 12'
For all other specify length
#FT - nominal length in feet
Continuous Run - for luminaires over 12'
VOLTAGE DRIVER ELECTRICAL MOUNTING FINISH CONTROLS OPTIONS
120 - 120V
277 - 277V
UNV - 120V-277V
347 - 347V
D - dimming 0-10V
DA - Dali
LHL# - Lutron Hi-Lume A
LEH - Lutron EcoSystem H
LE5 - Lutron EcoSystem 5
OTH - other (consult factory)
1 - 1 circuit
+#EB - emergency battery pack (for grid mounting
only min 4' fixture)
+#EM - emergency light circuit
+#NL - night light circuit
+GTD - generator transfer device
TG9 - tegular 9/16"
TG15 - tegular 15/16"
TB9 - t-bar 9/16"
TB15 - t-bar 15/16"
ST - screw slot t-bar
DMF - drywall mud flange
W - matte white
AL - aluminum
CF# - custom finish
specify RAL#
For grid mountings only
ONBOARD
OMS - Motion Sensor & power pack
ODS - Daylight Sensor & controller
WIRELESS
EWC - EnOcean Wireless Controller
LMC - Lutron Motion Controller
LDC - Daylight Controller
FU - fuse
FWC - flexible whip cable (6' std)
CP - Chicago Plenum
CU - custom
up to 111 lm/w performanceShown with in a grid ceiling Shown with in a drywall ceiling
DESCRIPTIONCava is a linear LED recessed
and pendant luminaire with a remarkably
comfortable and surprising appearance. Using
completely concealed and indirect LED arrays,
Cava provides superior brightness control,
while maintaining high efficacy by distributing
light over the vaulted interior cavity of the
luminaire. See separate spec sheets for other
available design and mountings.
CAVA LED RECESSED W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.RECESSED.SPEC February 19, 2015 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
OPTICSREDUCED LUMINANCE OPTIC (RLO) - Reduced Luminance Optic (RLO) consists of indirect-
mounted LED arrays illuminating a vaulted reflector with a matte white finish greater than 95%
reflectivity. The ultra-shallow arrays in RLO completely conceal the light source while evenly
distributing brightness over the entire surface of the cavity using a combination of multiple
reflective bounces and a very high diffuse reflectivity. Compared to diffusing optics, RLO reduces
luminaire brightness due to the visible interior surface being larger than the aperture.
LIGHT SOURCE - LEDCustom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
presented in accordance with IESNA LM-79, unless otherwise indicated.
PERFORMANCE PER 4' AT 4000K
LED output Color Temp Watts Nominal Lumens Efficacy Lumens Per Watt
low output 4000K 13 1400 111
medium output 4000K 19 2000 108
high output 4000K 28 3000 107
LUMINAIRE LENGTH
Cava is made up of standard 2, 3, 4, 5, 8 and 12 foot
sections that may be joined together to create longer
continuous run lengths. Nominal run length must be
noted in the product code. The minimum individual
section available is 2 foot.
All individual sections are joined together onsite using
the joiner kits provided. LumenWerx offers joiner kits
that are extremely simple to work with in the field and
result in a fixture that appears virtually seamless with
no light leak at any connection.
joining system for Cava recessed
ELECTRICAL Factory-set adjustable output current electronic driver with 120-277V AC line input.
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
and DALI protocol drivers.
For our drywall-mounted fixtures, a remote driver is provided
EMERGENCYFactory installed long life high temperature recyclable Ni-Cad battery pack with test
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
(25ºC) emergency lighting output. Recharge time of 24 hours.
MOUNTING OPTIONSRecess mount into exposed or concealed T-Bar or Tegular grid ceiling
Mounting for drywall ceilings is available with mud flange
5"5 1/8"
between T-bars
4 1/2" 4 1/2"
5"5 1/2"
between T-bars
4 1/2"
5"5 1/8"
between T-bars
TG9 - tegular 9/16" TG15 - tegular 15/16" TB9 - t-bar 9/16"
4 1/2"
5"5 1/2"
between T-bars
4 1/2"
5"5 1/8"
between T-bars
4 1/2"
4 5/8"hole width
7"with flanges
TB15 - t-bar 15/16" ST - screw slot t-bar DMF - drywall mud flange
CAVA LED RECESSED W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.RECESSED.SPEC February 19, 2015 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WEIGHTCava 4ft - 11.78lbs - 5.35kg
Cava 8ft - 22.91lbs - 10.4kg
Cava 12ft - 34.14lbs - 15.5kg
CERTIFICATIONSETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to
CAN/CSA Standard C22.2 No. 250.0.
Chicago plenum - City of Chicago Approved (CCEA)
WARRANTYLumenWerx provides a five-year limited warranty of electrical and mechanical
performance of the luminaires, including the LED boards, drivers, and auxiliary
electronics. LumenWerx will repair or replace defective luminaires or components at
our discretion, provided they have been installed and operated in accordance with our
specifications. Other limitations apply, please refer to the full warranty on our website.
FINISHInterior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
CONTROLSLumenWerx offers several options for integrating motion and daylight controls into Cava
luminaires. Wireless options incorporate a wireless controller/powerpack into the luminaire,
which receives signals from a wireless sensor (by others) installed in the space. The advantages
of the wireless option include greater flexibility of control options, sensor coverage and system
integration. Onboard options incorporate both the sensor and controller/powerpack. Onboard
sensors, while inherently simpler, have limitations of control and coverage.
Onboard Onboard Motion Sensor and power pack (OMS) provide automatic on and automatic off control,
using PIR detection. Sensor is designed to detect fine-motion when installed within 6' of occupants.
Onboard Daylight Sensor and controller (ODS) provide input for 0-10V dimming drivers. Separate
switched control of line input is required for on/off control.
2.5"
Location of an Onboard sensor
WirelessEnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTIONHousing - Extruded Aluminum 0.075" nominal, matte white or silver powder coating.
Custom finishes are also available.
Joiners - Die cast Aluminum (0.95" nominal)
Reflectors - Extruded Aluminum 0.07" nominal, 95% reflective matte white painted
CAVA SQUARE LED PENDANT DIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.SQUARE.PENDANT.DIRECT.SPEC February 19, 2015 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
ORDER GUIDE
CROSS SECTION
2 1/2"4 1/2"
4 1/2"
2 1/2"4 1/2"
4 1/2"
CAVSPD - air craft cable CAVSPD - stem
See page 2 for ordering code detailed information
PROJECT: __________________________________
____________________________________________
TYPE: ______________________________________
NOTES: ____________________________________
____________________________________________
CAVSPD RLO LED
LUMINAIRE ID END CAP OPTICS LIGHT SOURCE CRI LUMEN PACKAGES COLOR TEMP.
CAVSPD - cava square pendant direct OP - open end cap
CO - closed end cap
RLO - Reduced Luminance Optic LED - high performance LED 80 - 80CRI
90 - 90CRI (consult factory)
350 - low output 350lm/f
500 - medium output 500lm/f
750 - high output 750lm/f
30 - 3000k
35 - 3500k
40 - 4000k
LUMINAIRE LENGTH VOLTAGE DRIVER ELECTRICAL MOUNTING FINISH CONTROLS
Standard sections - 2', 3', 4', 5', 8' & 12'
For all other specify length
#FT - nominal length in feet
Continuous Run - for luminaires over 12'
120 - 120V
277 - 277V
UNV - 120V-277V
347 - 347V
D - dimming 0-10V
DA - Dali
LHL# - Lutron Hi-Lume A
LEH - Lutron EcoSystem H
LE5 - Lutron EcoSystem 5
OTH - other (consult factory)
1 - 1 circuit
+#EB - emergency battery pack
(for min 4' fixture)
+#EM - emergency light circuit
+#NL - night light circuit
+GTD - generator transfer device
53WAC36 - power 5" + non power
3" white canopy (36" air craft cable)
55WSW18 - power 5" + non power
5" white canopy & stem (18" stem)
For all other mountings refer to the
Pendant Mounting Guide.
W - matte white
AL - aluminum
CF# - custom finish specify RAL#
ONBOARD
OMS - Motion Sensor & power pack
ODS - Daylight Sensor & controller
WIRELESS
EWC - EnOcean Wireless Controller
LMC - Lutron Motion Controller
LDC - Daylight Controller
OPTIONS
FU - fuse
TB# - T-bar caddy clip specify grid size
TG# - Tegular caddy clip specify grid size
ST - Screw Slots caddy clip
CU - custom
up to 111 lm/w performance
DESCRIPTIONCava is a linear LED pendant
luminaire with a remarkably comfortable and
surprising appearance. Using completely
concealed and indirect LED arrays, Cava
provides superior brightness control, while
maintaining high efficacy by distributing light
over the vaulted interior cavity of the luminaire.
Cava offers totally direct or segmented
direct/indirect distributions. See separate spec
sheets for other available design.
Shown with a open end cap Shown with an closed end cap
CAVA SQUARE LED PENDANT DIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.SQUARE.PENDANT.DIRECT.SPEC February 19, 2015 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
OPTICSREDUCED LUMINANCE OPTIC (RLO) - reduced Luminance Optic (RLO) consists of indirect-
mounted LED arrays illuminating a vaulted reflector with a matte white finish greater than 95%
reflectivity. The ultra-shallow arrays in RLO completely conceal the light source while evenly
distributing brightness over the entire surface of the cavity using a combination of multiple
reflective bounces and a very high diffuse reflectivity. Compared to diffusing optics, RLO reduces
luminaire brightness due to the visible interior surface being larger than the aperture.
LIGHT SOURCE - LEDCustom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
presented in accordance with IESNA LM-79, unless otherwise indicated.
PERFORMANCE PER 4' AT 4000K
LED output Color Temp Watts Nominal Lumens Efficacy Lumens Per Watt
low output 4000K 13 1400 111
medium output 4000K 19 2000 108
high output 4000K 28 3000 107
LUMINAIRE LENGTH
Cava is made up of standard 2, 3, 4, 5, 8 and 12 foot
sections that may be joined together to create longer
continuous run lengths. Nominal run length must be
noted in the product code. The minimum individual
section available is 2 foot.
All individual sections are joined together onsite using
the joiner kits provided. LumenWerx offers joiner kits
that are extremely simple to work with in the field and
result in a fixture that appears virtually seamless with
no light leak at any connection.
joining system for Cava square
ELECTRICAL Factory-set adjustable output current electronic driver with 120-277V AC line input.
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
and DALI protocol drivers.
EMERGENCYFactory installed long life high temperature recyclable Ni-Cad battery pack with test
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
(25ºC) emergency lighting output. Recharge time of 24 hours.
MOUNTING OPTIONSFixtures can be pendant-mounted, using air craft cables, or stem-mounted.
Unless otherwise specified, LumenWerx provides the following hardware:
For cable-mounted fixtures - 53WAC36 (5" white canopy for all power mounting
point, 3" white canopy for non power mounting point, and a 36" cable)
For stem mounted fixtures - 55WSW18 (5" white canopy for all power mounting
point, and non power mounting point, and a 18" white stem)
Caddy clips, if required specify under OPTIONSFor all other required mountings options, for all our Pendant Mounting Guide at
www.lumenwerx.com
FINISHInterior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
CONTROLSLumenWerx offers several options for integrating motion and daylight controls into
Cava luminaires. Wireless options incorporate a wireless controller/powerpack into
the luminaire, which receives signals from a wireless sensor (by others) installed in
the space. The advantages of the wireless option include greater flexibility of control
options, sensor coverage, and system integration. Onboard options incorporate both
the sensor and controller/powerpack. Onboard sensors, while inherently simpler,
have limitations of control and coverage.
CAVA SQUARE LED PENDANT DIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.SQUARE.PENDANT.DIRECT.SPEC February 19, 2015 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WARRANTYLumenWerx provides a five-year limited warranty of electrical and mechanical
performance of the luminaires, including the LED boards, drivers, and auxiliary
electronics. LumenWerx will repair or replace defective luminaires or components at
our discretion, provided they have been installed and operated in accordance with our
specifications. Other limitations apply, please refer to the full warranty on our website.
OnboardOnboard Motion Sensor and power pack (OMS) provide automatic on and automatic off control,
using PIR detection. Sensor is designed to detect fine-motion when installed within 6' of occupants.
Onboard Daylight Sensor and controller (ODS) provide input for 0-10V dimming drivers. Separate
switched control of line input is required for on/off control.
2.5"
Location of an Onboard sensor
WirelessEnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.
CONSTRUCTIONHousing - Extruded Aluminum 0.075" nominal, matte white or silver powder coating.
Custom finishes are also available.
End cap - Die cast Aluminum (0.95" nominal)
Joiners - Die cast Aluminum (0.95" nominal)
Reflectors - Extruded Aluminum 0.07" nominal, 95% reflective matte white painted
Hanger - Chromed Griplock securely attached with spring steel hardware in end caps and/or
joiners
Air craft cable suspension - 7x7 braids Aluminum air craft cable 0.06" thick
Stem - 0.5" diameter threaded steel tube matte white or silver powder coating. Custom finishes are
also available
WEIGHTCava square 4ft - 14.10lbs - 6.4kg
Cava square 8ft - 27.53lbs - 12.5kg
Cava square 12ft - 40.97lbs - 18.6kg
CERTIFICATIONSETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to CAN/CSA
Standard C22.2 No. 250.0.
CAVA SQUARE LED PENDANT DIRECT/INDIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.SQUARE.PENDANT.DIRECT-INDIRECT.SPEC February 19, 2015 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
ORDER GUIDE
CROSS SECTION
2 1/2"4 1/2"
4 1/2"
2 1/2"4 1/2"
4 1/2"
CAVCPDI - air craft cable CAVCPDI - stem
See page 2 for ordering code detailed information
PROJECT: __________________________________
____________________________________________
TYPE: ______________________________________
NOTES: ____________________________________
____________________________________________
CAVSPDI RLO LED
LUMINAIRE ID END CAP OPTICS LIGHT SOURCE CRI DIRECT LUMEN PACKAGES INDIRECT LUMEN PACKAGES COLOR TEMP.
CAVSPDI - cava square
pendant direct indirect
OP - open end cap
CO - closed end cap
RLO - Reduced Luminance Optic LED - high performance LED 80 - 80CRI
90 - 90CRI (consult factory)
350 - low output 350lm/f
500 - medium output 500lm/f
750 - high output 750lm/f
500 - low output 500lm/f
750 - medium output 750lm/f
30 - 3000k
35 - 3500k
40 - 4000k
LUMINAIRE LENGTH VOLTAGE DRIVER ELECTRICAL MOUNTING FINISH CONTROLS
Standard sections - 2', 3', 4', 5', 8' & 12'
For all other specify length
#FT - nominal length in feet
Continuous Run - for luminaires over 12'
120 - 120V
277 - 277V
UNV - 120V-277V
347 - 347V
D - dimming 0-10V
DA - Dali
LHL# - Lutron Hi-Lume A
LEH - Lutron EcoSystem H
LE5 - Lutron EcoSystem 5
OTH - other (consult factory)
1 - 1 circuit
2 - 2 circuits
+#EB - emergency battery pack
(for min 4' fixture)
+#EM - emergency light circuit
+#NL - night light circuit
+GTD - generator transfer device
53WAC36 - power 5" + non power
3" white canopy (36" air craft cable)
55WSW18 - power 5" + non power
5" white canopy & stem (18" stem)
For all other mountings refer to the
Pendant Mounting Guide.
W - matte white
AL - aluminum
CF# - custom finish specify RAL#
ONBOARD
OMS - Motion Sensor & power pack
ODS - Daylight Sensor & controller
WIRELESS
EWC - EnOcean Wireless Controller
LMC - Lutron Motion Controller
LDC - Daylight Controller
OPTIONS
FU - fuse
DC - dust cover
TB# - T-bar caddy clip specify grid size
TG# - Tegular caddy clip specify grid size
ST - Screw Slots caddy clip
CU - custom
Shown with a open end cap Shown with an closed end cap
DESCRIPTIONCava is a linear LED pendant
luminaire with a remarkably comfortable and
surprising appearance. Using completely
concealed and indirect LED arrays, Cava
provides superior brightness control, while
maintaining high efficacy by distributing light
over the vaulted interior cavity of the luminaire.
Cava offers totally direct or segmented
direct/indirect distributions. See separate spec
sheets for other available design.
up to 106 lm/w performance
CAVA SQUARE LED PENDANT DIRECT/INDIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.SQUARE.PENDANT.DIRECT-INDIRECT.SPEC February 19, 2015 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
OPTICSREDUCED LUMINANCE OPTIC (RLO) - reduced Luminance Optic (RLO) consists of indirect-
mounted LED arrays illuminating a vaulted reflector with a matte white finish greater than 95%
reflectivity. The ultra-shallow arrays in RLO completely conceal the light source while evenly
distributing brightness over the entire surface of the cavity using a combination of multiple
reflective bounces and a very high diffuse reflectivity. Compared to diffusing optics, RLO reduces
luminaire brightness due to the visible interior surface being larger than the aperture.
LIGHT SOURCE - LEDCustom linear array of mid-flux LED's are cartridge-mounted with quick-connect wiring to facilitate
service and thermal management. Available in 3000K, 3500K and 4000K with a minimum 80 CRI
and an option for 90 CRI with elevated R9 value. Color consistency maintained to within 3 SDCM.
LEDs operated at reduced drive current to optimize efficacy and lumen maintenance.
All LEDs have been tested in accordance with IESNA LM-80-08 and the results have shown L80
lumen maintenance greater than 60,000 hours. Absolute product photometry is measured and
presented in accordance with IESNA LM-79, unless otherwise indicated.
PERFORMANCE PER 4' AT 4000K
High Indirect Output (3000 Lumens)
LED output Color Temp
Watts Direct
Lumens
Indirect
Lumens
Total Nominal Lumens
Efficacy Lumens Per Watt
low output 4000K 42 1400 3000 4400 104
medium output 4000K 48 2000 3000 5000 104
high output 4000K 58 3000 3000 6000 104
Low Indirect Output (2000 Lumens)
LED output Color Temp
Watts Direct
Lumens
Indirect
Lumens
Total Nominal Lumens
Efficacy Lumens Per Watt
low output 4000K 32 1400 2000 3400 106
medium output 4000K 38 2000 2000 4000 105
high output 4000K 48 3000 2000 5000 105
LUMINAIRE LENGTH
Cava is made up of standard 2, 3, 4, 5, 8 and 12 foot
sections that may be joined together to create
longer continuous run lengths. Nominal run length
must be noted in the product code. The minimum
individual section available is 2 foot.
All individual sections are joined together onsite
using the joiner kits provided. LumenWerx offers
joiner kits that are extremely simple to work with in
the field and result in a fixture that appears virtually
seamless with no light leak at any connection.
joining system for Cava square
ELECTRICAL Factory-set adjustable output current electronic driver with 120-277V AC line input.
Dimmable from at least 100%-5% with 0-10V control. Rated life (90% survivorship)
of 50,000 hours at 50ºC max. ambient (and 70ºC max. case) temperature. Terminal
block connections for easy service. At maximum driver load: Efficiency>84%, PF>0.9,
THD<20%. Other specifiable options include Lutron Hi-Lume A (specify 2, 3 or 4 wires),
EcoSystem H (100%-1%, fade-to-black) and EcoSystem 5 (100%-5%) dimmable drivers
and DALI protocol drivers.
EMERGENCYFactory installed long life high temperature recyclable Ni-Cad battery pack with test
switch and charge indicator, minimum of 90 minutes operation, up to 1300 lumens
(25ºC) emergency lighting output. Recharge time of 24 hours.
CAVA SQUARE LED PENDANT DIRECT/INDIRECT W W W . L U M E N W E R X . C O M
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. File Name: CAVA.SQUARE.PENDANT.DIRECT-INDIRECT.SPEC February 19, 2015 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
CONSTRUCTIONHousing - Extruded Aluminum 0.075" nominal, matte white or silver powder coating.
Custom finishes are also available.
End cap - Die cast Aluminum (0.95" nominal)
Joiners - Die cast Aluminum (0.95" nominal)
Reflectors - Extruded Aluminum 0.07" nominal, 95% reflective matte white painted
Hanger - Chromed Griplock securely attached with spring steel hardware in end caps
and/or joiners
Air craft cable suspension - 7x7 braids Aluminum air craft cable 0.06" thick
Stem - 0.5" diameter threaded steel tube matte white or silver powder coating.
Custom finishes are also available
WEIGHTCava square 4ft - 14.10lbs - 6.4kg
Cava square 8ft - 27.53lbs - 12.5kg
Cava square 12ft - 40.97lbs - 18.6kg
CERTIFICATIONSETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to
CAN/CSA Standard C22.2 No. 250.0.
WARRANTYLumenWerx provides a five-year limited warranty of electrical and mechanical
performance of the luminaires, including the LED boards, drivers, and auxiliary
electronics. LumenWerx will repair or replace defective luminaires or components at
our discretion, provided they have been installed and operated in accordance with our
specifications. Other limitations apply, please refer to the full warranty on our website.
MOUNTING OPTIONSFixtures can be pendant-mounted, using air craft cables, or stem-mounted.
Unless otherwise specified, LumenWerx provides the following hardware:
For cable-mounted fixtures - 53WAC36 (5" white canopy for all power mounting point, 3" white
canopy for non power mounting point, and a 36" cable)
For stem mounted fixtures - 55WSW18 (5" white canopy for all power mounting point, and non
power mounting point, and a 18" white stem)
Caddy clips, if required specify under OPTIONSFor all other required mountings options, for all our Pendant Mounting Guide at
www.lumenwerx.com
FINISHInterior - 95%, reflective matte powder coated white paint
Exterior - matte white or silver powder coating.
Custom finishes are also available.
CONTROLSLumenWerx offers several options for integrating motion and daylight controls into Cava
luminaires. Wireless options incorporate a wireless controller/powerpack into the luminaire,
which receives signals from a wireless sensor (by others) installed in the space. The advantages
of the wireless option include greater flexibility of control options, sensor coverage and system
integration. Onboard options incorporate both the sensor and controller/powerpack. Onboard
sensors, while inherently simpler, have limitations of control and coverage.
OnboardOnboard Motion Sensor and power pack (OMS) provide automatic on and automatic off control,
using PIR detection. Sensor is designed to detect fine-motion when installed within 6' of occupants.
Onboard Daylight Sensor and controller (ODS) provide input for 0-10V dimming drivers. Separate
switched control of line input is required for on/off control.
2.5"
Location of an Onboard sensor
WirelessEnOcean Wireless Controller (EWC) provides both a power pack for presence detection control
and a 0-10V interface for daylight harvesting. EnOcean wireless sensors (by others) mounted in the
room signal the onboard EWC. This option permits manual on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Daylight Controller (LDC) provide inputs to Ecosystem
drivers. Compatible Lutron wireless motion and daylight sensors (by others) mounted in the room
signal onboard LPC or LDC. This option permits manual on/automatic off (vacancy) control.