BITTNER Application Note XR SXL II AX16...Bittner SXL II Control Interface Assembly of the Amplifier...
Transcript of BITTNER Application Note XR SXL II AX16...Bittner SXL II Control Interface Assembly of the Amplifier...
Application
NoteXR
SXL II
AX16
The Solution:
1. Amplifiers
2. Control Interface
3. Automatic Amplifier Switch
Bittner XR amplifiers with integrated DSP allow for an accurate adjustment of the
settings for the relevant public address areas at loads down to 2 ohms (level, EQ,
delay, dynamics)
Bittner SXL II Control Interface:
monitoring and control of up to 16 channels
permanent line and amplifier monitoring according to EN-60849
permanent evaluation of control signals
control of the AX16 amplifier switch incl. the transfer of DSP settings
integrated webserver allows configuration and storage of different setups as
well as readout of the logfile
Bittner AX16 Intelligent Amplifier Switch:
noiseless switching of the inputs and outputs of a defective amplifier incl.
automatic transfer of DSP settings and level to a backup unit
14 signal channels and 2 backup channels with three different switching
modes (7+1, 3+1 or 1+1)
n
n
n
n
n
n
n
The Job:
Low-impedance public address system with optimal intelligibility and system
reliability according to EN-60849 incl. permanent line and amplifier monitoring.
large venues such as stadiums, multipurpose venues,
congress centers, theaters, or cinemas
big events such as open air, public viewing, tour
productions
in fixed installations:
for mobile sound systems:
n
n
BITTNERAUDIO
Bittner SXL II Control Interface
Assembly of the Amplifier Rack
Bittner AX16 Intelligent Amplifier Switch (Mode 7+1)
SXL data bus SXL II outputs pilot tone
SPEAKER OUT CH 1+2
AUDIO IN CH 1+2BACKUP CH15+16
Bittner XR Amplifier with integrated DSP (backup amplifier)
Bittner XR Amplifier with integrated DSP (amplifier in use)
Application
NoteXR
SXL II
AX16
BITTNERAUDIO
Function: Permanent Line Monitoring
SXL II
n
n
n
n
n
n
time controlled pilot tone via SXL II (e. g. every 90 sec)
the amplifiers monitor their output lines synchronically to the pilot tone
monitoring of input signals
reporting of measuring results from the amplifier to the SXL II via the data bus
display of the data in the SXL web interface, the SXL front panel and in the SXL
log file
activation of a relais contact in case of a malfunction (SXL relays 1 to 8 user
configurable)
BITTNERAUDIO
Application
NoteXR
SXL II
AX16
Public Address SystemL
S
Mic
Amp
Data Port
SXL IISignal
Generator
Amplifier Switching incl. the Transfer of DSP Settings
SXL II Block Diagram AX16 Block Diagram
Activation of the AX16 Intelligent Amplifier Switch by SXL II
n
n
n
n
a defective XR amplifier is detected via SXL data bus
corresponding command for audio switching to the AX16 via SXL data bus
all XR parameters are transferred via SXL data bus to backup amplifier incl.
level and DSP settings
message and display of backup switching at the front LEDs of the AX16,
configurable error relays, and the SXL log file
BITTNERAUDIO
DisplayLEDs
DIPSwitches
Data
Port
ContactsAlive
Active
O
u
t
p
u
t
S
t
a
g
e
AliveContactsAmplifiers
Processor
Amp 1
Amp 2
Amp 3
Amp 4
Amp 5
Amp 6
Amp 7
Amp 8
I
n
p
u
t
S
t
a
g
e
L
e
v
e
l
RelaysLogical
Inputs
Processor
Front Panel Elements
LCD, Buttons, LEDsEthernet SD
Card
FlashDisk
Data Ports Paging & Monitor Buses
Application
NoteXR
SXL II
AX16