1633 Thornwood Dr. RHINO CARBON FIBER™ CRACK REPAIR … · 2019-09-13 · •Make sure crack will...

RHINO CARBON FIBER™ CRACK REPAIR INSTRUCTIONS 01

WHAT COMES IN THE CRACK REPAIR KIT?

KIT INCLUDES

•(1) 12” wide carbon fiber strap (length is determined by kind of kit)•(2) Tubes of Saturant-Adhesive Epoxy•(2) Static epoxy nozzles•Gloves and Instructions

•Safety Goggles •Scissors•Respirator Mask •Marker•Hard Hat •Hydraulic Cement•Coveralls •Epoxy Gun•Drop Cloth •Measuring Tape•Gravel •Shovel/bucket

YOU WILL ALSO NEED...

10-Gallon HEPADust Extractor

5-Inch Surface GrindingDust Shroud Kit

RECOMMENDED POWER TOOLS

Use for grinding foundation wall

Cutting and Tuck Pointing Dust Shroud Tool

Collects dust while attached to grinder and shroud tools

Use to tuckpoint the wall**USE DIAMOND EDGE BLADE **USE DIAMOND CUP WHEEL

1633 Thornwood Dr. Heath, OH 43056 USA

P: +1 888 684 3889 E: [email protected]

PRODUCTS COMMONLY USED WITH CRACK REPAIR

Rhino Carbon Fiber™ Dual Epoxy GunRCF™ High Strength Anchoring

Epoxy Paste Tough Wipes by Rhino Carbon Fiber™

300/300 ml or 300/150 ml gun Used to fill cracks Removes Epoxy!

SAFETY WARNINGS

Please read and follow safety procedures for all tools and wearproper safety equipment during installation.

While using power tools follow all EPA/OSHA guidelines forlead paint removal and respiratory protection. For moreinformation visit www.epa.gov or www.osha.gov

Hammer Drill

Use for concrete removal**USE CHISEL OR SPADE TIP ATTACHMENT

Rhino Carbon Fiber™ Concrete Crack Lock® stitches

Adds extra strength during repair

© All Rights Reserved

1-888-684-3889 | www.RhinoCarbonFiber.com

PLEASE READ ALL DIRECTIONS CAREFULLY & WEAR SAFETY GOGGLES BEFORE INSTALLING

01 PREP

•Please read and follow safety prodecures for all tools and wear all safetyequipment during installation.

•Locate where Rhino Carbon Fiber Crack Repair Kit will be installed.•Mark the crack at the top, middle and bottom of the wall.

Tools: Marker

0102 CONCRETE REMOVAL

•Remove 14” of concrete from the center of the crack

Note: Concrete should be removed past the edge of the footer

Recommended Tools: Hammer Drill

02

01

RHINO CARBON FIBER™ CRACK REPAIR INSTRUCTIONS

•Grind foundation wall where the crack repair material will be installed•Achieve a “Bare Foundation”•Rhino Carbon Fiber Crack Repair should span from the sill place to the footer

Note: Remove all caulk/latex/etc. from work area

Tools: Grinder

03 GRINDING

FILL04

• Fill crack with High Strength Anchoring Epoxy Paste or hydraulic cement beforemounting carbon fiber

Tools: High Strength Anchoring Epoxy Paste or Hydraulic Cement and Epoxy Gun





MOUNT05

Tools: Measuring tape and scissors/utility knife

•Measuring the height of the foundation wall from the sill plate to the footerand add 6”

•Cut carbon fiber to length•Make sure crack will be comletely covered by carbon fiber

•Apply thin layer of epoxy to the foundation wall working from top to bottom coveringentire ground surface

•Once a sufficient coating of epoxy is applied to foundation wall, lay carbon fiber crackrepair over the epoxy ensuring the carbon fiber completely covers the crack

•Use squeege over epoxy for both foundation wall and carbon fiber strap•Use light strokes with squeege to spread epoxy evenly focusing on the edges for aclean

Tools: Saturant-Adhesive Epoxy, Epoxy Gun and Squeege

•Using gravel or small pieces of concrete leftover from removal, fill area leaving aminiumum of 3” for new concrete

Tools: Gravel

EPOXY

BACKFILL REPLACEMENT

06

07



03

•Mix concrete per manufacturers recommendations•Pour concrete into work area and trowel to a smooth, uniform finish

Tools: Concrete, Bucket, Shovel and Trowel

FINISH 08

RHINO CARBON FIBER™ CRACK REPAIR INSTRUCTIONS



1633 Thornwood Dr. RHINO CARBON FIBER™ CRACK REPAIR … · 2019-09-13 · •Make sure crack will...

Documents

Transcript of 1633 Thornwood Dr. RHINO CARBON FIBER™ CRACK REPAIR … · 2019-09-13 · •Make sure crack will...