8/8/2019 10 Up Kia Soul Grille Installation Manual Carid

1/3

Quantity Description Part No.11111

Upper Fine Mesh SectionLower Mesh Grille SurroundLower Fine Mesh SectionFront Tag BezelHardware Kit (items listed below)(6) #6 x 3/4 T-10 Torx Screws(1) T-10 Torx Bit(3) .130 x 5 Black Cable Ties(4) .045 x .250 Double Faced Tape(30) .045 x 1 Double Faced Tape

1232-0020-101232-0022-101232-0021-101232-0710-101232-1902-103999-9107-003999-9108-001999-0301-003004-9250-923004-9244-92

IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCECopyright 2009 by E&GClassics, Inc.

All right reserved. The repro-duction or utilization of thiswork in any form or any elec-tronic, mechanical, or othermeans, no known or hereaf-ter invented, including xerog-

raphy, photocopying, and re-cording, and in any informa-tion storage retrieval systemis forbidden without writtenpermission of owners.

Notes to the Technician:

E&G is proud to present this package toyou and reminds you that for technical in-formation, contact Lynn Eash or Lee Claryat 410-381-4900. Do not attempt instal-

lation any E&G product without first read-ing the detailed instructions. E&G Classicswill not warrant damaged parts or vehicledue to altered installation instructions.

2010 Kia SoulUpper and Lower

Stainless SteelMesh Grilles

L 28 G9P

Mesh Grille Part # 1232-0102-10

*USE CAUTION* while handling the grille. Thestainless steel edges and mesh can be very sharp.

2. Apply the supplied double faced tape to the factorygrille surround and overlay the mesh section intoplace, making sure all edges of the mesh fit inside

the surround.

3. Apply protective masking tape to the lower edgesof the grille opeing and tag surround.4. Carefully align the lower mesh grille assembly intoplace and use masking tape to hold it in place dur-ing the following procedure.

5. Install the no.6 x 3/4 Torx screws using the sup-plied T-10 torx bit and a slow speed drill, allowingthe screws to self tap into the plastic grille opening.DO NOT OVERTIGHTEN or you will strip out themounting holes.

4

1. Remove the factory grille lettering using a 10mmsocket wrench and a phillips screwdriver to remove

the bolts and push fasteners across the top of thebumper cover..

1

6. Finish the installation of all #6 x 3/4 Torx Screws,working from the center out to the bottom corners.

6

8/8/2019 10 Up Kia Soul Grille Installation Manual Carid

2/3

2 Copyright 2009 by E&G Classics, Inc.

8. Carefully align the upper mesh section into the fac-tory upper grille opening and use masking tape onthe sides and bottom to hold the mesh section inplace during the following installation procedure.

9. Pre-bend the supplied black cable ties approx. 1after the alignment/starter tab portion of the cabletie.

11. Find a wire that lines up over an existing factorygrille secton. Insert the bent over black cable tie inthe opening next to the wire, then pull the blackcable tie back out through the grille once the bentedge aligns into the adjacent grille opening. Begin

tightening the black cable tie, leaving enoughslack to rotate the cable tie head to the back ofthe factory grille.

12

7,8

7. Apply protective masking tape to the lower edge ofthe upper factory grille opening.

7 8

9

1

10. These are the approxiamte locations inwhich youare going to install the supplied black cable ties.

1011

12. Use long nose pliers to reach down and snug thecable ties so that the mesh is tight against the fac-tory grille insert.

12

8/8/2019 10 Up Kia Soul Grille Installation Manual Carid

3/3