2003 2007 Hummer h2 Grille Installation Manual Carid

download 2003 2007 Hummer h2 Grille Installation Manual Carid

of 4

Transcript of 2003 2007 Hummer h2 Grille Installation Manual Carid

  • 8/8/2019 2003 2007 Hummer h2 Grille Installation Manual Carid

    1/4

    http://www.carid.com/hummer-grill/http://www.carid.com/hummer-accessories/http://www.carid.com/
  • 8/8/2019 2003 2007 Hummer h2 Grille Installation Manual Carid

    2/4

    2 Copyright 2007 by E&G Classics, Inc.

    10. Use a 3/32 drill bit to drill through the exact cen-ter of the frame outer mounting holes.

    13. Align the Ultimate grille over the factory grille.Install one screw on each side to properly centerthe grille, then press the block out panel firmly inplace to set the tape.14. Remove the frame once the block out panel isadhered to the factory grille.

    11. Paint the front of the ABS block out panel withsemigloss black paint, as unpainted ABS will grad-ually turn gray with UV exposure.

    11

    12. Peel off the backing on the double faced tape andcarefully align the painted ABS block out panelinside the machined opening of the E&G Ultimategrille.

    12

    7,8

    7. Once the paint has cured and the masking paperremoved, measure down from the inside top ofthe factory grille opening 7-9/16 and mark themasking tape.

    8. Align the CNC Chrome grille frame even with themarks made in Step 7 and make sure the frame isperfectly centered.9. Mark the side four (4) mounting holes onto themasking tape (extra help is highly recom-mended in keeping the grille properly alignedwhile marking the hole locations) and remove thegrille frame.

    7

    9

    Car Accessories | Hummer Accessories | Hummer Grilles

    http://www.carid.com/hummer-grill/http://www.carid.com/hummer-accessories/http://www.carid.com/
  • 8/8/2019 2003 2007 Hummer h2 Grille Installation Manual Carid

    3/4

    3 Copyright 2007 by E&G Classics, Inc.

    17. Use a pen, pencil or small screwdriver to pushdown on the mesh to make sure the mesh isdown tight against the inside edge of the Ultimategrille.

    17

    18

    16. Align the mesh section by placing it behind theUltimate grille frame and infront of the paintedABS grille block out. Do not allow the mesh toscratch the painted ABS grille block out as youlower it into position.

    15. Remove the protective masking tape and installthe frame and using the supplied 1/2 no.6 countersunk phillips screws across the bottom edgeonly. DO NOT TIGHTEN THE SCREWS, leave them1/8 from contacting the grille frame.

    18. Finish installing the Ultimate grille frame onto thefactory grille using the supplied #6 x 1/2 counter-sunk phillips screws. DO NOT OVERTIGHTEN ORYOU WILL STRIP OUT THE HOLES IN THE PLASTIC.19. Thoroughly clean the installed frame using alcoholor glass cleaner to remove any grease or fingerprints.

    20. Install the supplied .040 x .250 double facedtape to the back of the stainless steel overlay.21. Peel back a small section of tape and carefully alignthe polished overlay onto the Ultimate grille, mak-ing sure it is perfectly centered in the recess.

    Carefully peel off the double faced tape backingand press the polished overlay into place.

    22. Align the lower frame onto the factory lower grillesection. Use a 3/32 drill bit to drill through theholes in the frame and into the plastic. Wheninstalling the upper no.6 x 3/4 screws, install thesupplied 5/16 plastic spacer to keep the top of

    the frame at the correct height.

    22

    15

    21

    Car Accessories | Hummer Accessories | Hummer Grilles

    http://www.carid.com/hummer-grill/http://www.carid.com/hummer-accessories/http://www.carid.com/
  • 8/8/2019 2003 2007 Hummer h2 Grille Installation Manual Carid

    4/4

    http://www.carid.com/hummer-grill/http://www.carid.com/hummer-accessories/http://www.carid.com/