11 Up Honda Accord Coupe Grille Installation Manual Carid
-
Upload
enthonytopmak -
Category
Documents
-
view
218 -
download
0
Transcript of 11 Up Honda Accord Coupe Grille Installation Manual Carid
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 1/7
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE !Copyright © 2010 by E&G Classics, Inc. All right reserved. The reproduction or utilization of this work in any form or any electronic, mechanical, or other means, no known or hereaf ter invented,
including xerography, photocopying, and recording, and in any infor mation storage retrieval system is for bidden without written per mission of owners.
Part #: Complete #1124-0102-11 / “Black Ice” Part #1124-B102-11Upper Part #1124-010U-11 / Lower Part #1124-010L-11
Notes to the Technician/Installer:E&G is proud to present this package to you and reminds you that for tech-nical infor mation, contact Lynn Eash or Lee Clary at 410-381-4900. Do not
attempt the in stallation of any E&G product without first reading the detailed
instructions. E&G Classics will not war rant damaged parts or the vehi-
cle due to altered installation instructions.
J 13 HO P
Important information before you begin:
If this E&G grille installation kit includes grille hole location template(s) to drill mounting holes in the vehicle,
you MUST verify that the template(s) provided in this kit match the mounting pin locations on the grille(s).
Prior to drilling the mounting holes, place the assembled grille’s mounting pins over the template(s) provided
and make sure that the pin and hole locations are the same. If they do not match, please call 410-381-4900
and ask for technical assistance. Thank you.
1. Open the hood and remove a total of thirteen (13) factory plastic
push fasteners. Remove them by lifting up on the center part of
the factener until it locks in place, then remove the entire fastener.
Once the fasteners are removed, lift up and remove the radiator
support panel.
2. Apply several layer of masking tape around the factory grille to
protect the paint on the bumper cover during factory grille re-
moval.
Copyright 2010 by E&G Classics, Inc. Visit us online today at www.egclassics.com
2011 Honda Accord Coupe Fine Mesh Grille
TOOLS REQUIREDWide masking tape, large and small flat blade screwdrivers, electric drill, 1/8” and 5/16” drill bits, sissors,
awl or pointed tool, Sharpie marker or grease pencil, soft clean cloths, solvent, glass cleaner or alcohol.
Replacement Upper / Lower Overlay
3. Remove the upper outer factory phillips screws retaining the outer
corners of the factory grille to the bumper cover.
4. Use a flat blade screwdriver and insert it between the grille
mounting tabs and the bumper cover. Twist the screwdriver
slightly until the tab releases and allow you to begin pulling the
grille forward.
1
2 2
3
4
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 2/7
5. Use a long flat blade screwdriver to remove the outer lower
mounting push fasteners by pushing down on the center of the ex-
posed underside of the pin. The inner lower mounting push fas-
teners will use a smaller flat blade screwdriver and you must in-
sert the screwdriver between the pin and the body of the push fas-
tener and twist until it releases (not shown).
6. Once the factory push fasteners are removed from the bottom of
the grille, pull the grille straight out to remove it from the bumper
cover.
7. Remove the factory emblem by inserting a small flat blade screw
driver under the push on retainers and twist them until the mount-
ing pins snap off.
8. Install the supplied .045” x .250” double faced tape to the back of
the factory emblem as shown.9. Peel the backing from the installed double faced tape. align the
remaining portions of the factory alignment pins with the holes in
the supplied emblem mounting plate and press the emblem firmly
onto the plate to set the tape.
Copyright 2010 by E&G Classics, Inc. Visit us online today at www.egclassics.com
10. Apply additional masking tape around the upper grille opening
(even with the factory grille mounting channel) and apply mask-
ing tape around the lower bumper opening.
11. Use a tape measure to locate and mark the exact center of the
grille opening. Measure between two symetrical points and di-
vide that measurement in half. Use a grease pencil or sharpie
marker and draw a line as shown.
5
7
8
8
1011
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 3/7
12. Cut out and align the supplied upper grille hole location tem-
plate, and once properly aligned with the rear edge pushed into
the factory mounting channel, use masking tape to secure it.
13. Use an awl or similar pointed tool to mark the hole locations
onto the bumper cover. Remove the template, flip it over and
mark the holes on the opposite side.
14. Use a .125” (1/8”) drill bit to drill through the marks made in the
previous step. Use the drill bit to connect the holes, making
small slots allowing for slight left to right grille adjustments.
15. Cut out the supplied upper outer hole location template and use
masking tape to tape it up into the upper corner of the factory
grille opening. Use an awl or similar pointed tool to mark the hole
location onto the bumper cover. Remove the template, flip it
over, tape and mark the holes on the opposite side.
16. Use a 5/16” drill bit to drill through the marks made in the previ-
ous step and use the drill bit to connect the holes to create wide
enough slots to allow the upper grille outer mounting studs to
pass through.
Copyright 2010 by E&G Classics, Inc. Visit us online today at www.egclassics.com
17. Use fine sandpaper or a scotch brite pad to scuff the paint on
the upper grille opening and the center bar of the lower grille
opening.
18. Paint everything that would visible through the mesh grille with
flat or semi-gloss black paint, including the factory grille mount-
ing channel and inner bumper reinforcement.
12
13
14
15 16
17
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 4/7
19. Align the lower mesh section over the back of the lower mesh
surround.
20. Trim the ends from the supplied black cap plugs and install them
over the lower mounting studs only.
21. Align the lower mesh grille asembly into place and begin se-
curing it with the supplied large black plastic washers and
the #8-32 ESNA half nuts. Hand tighten only at this time.
22. Before tighten the mounting hardware on the lower grille, re-
move any masking tape that could get caught behind the mesh
grille once it is tightened. Shift the grille around if the tape be-
gins to get caught behind the mesh surround.
23. Use a 9mm or 11/32” deep socket and ratchet to tighten the
lower grille mounting hardware. Tighten only until the washer no
longer rotate freely. DO NOT OVERTIGHTEN or you will indent
the mesh surround at the stud locations.
24. Remove the masking tape from the upper grille surround, then
retape up to the forward edge of the mounting holes.
25. Install the emblem assembly on the mesh section using the sup-
plied large black plastic washers, #10 lock washers and #8-32
stainless steel hex nuts.
20
19
22
24
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 5/7
26. Align the assembled mesh grille onto the bumper cover, making
sure that the lower mounting pins fit into the holes drilled previ-
ously.
27. Lift up on the top edge of the bumper cover and beginning at
the center, pass the upper mounting tabs through the slots in the
bumper cover. Be extra careful not to damage the paint on the
edge of the bumper cover!
29. Use a flat blade screwdriver to bend the upper mounting tabs to
secure the top edge of the grille tightly to the bumper cover.
Make sure you push the grille into the bumper cover as tightly as
you can while bending the mounting tabs
28. Once the outer studs pass through the holes drilled previously,
pull the grille and bumper cover forward and install a large black
plastic washer and a #8-32 ESAN half nut and tighten com-
pletely.
30. Remove the protective tape around the upper mesh grille,
pulling it straight out to minimize tape breakage.
31. Reinstall the radiator support panel cover, reusing the factory
push fasteners.
27
28
30 31
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 6/7
32. Remove a small portion of the front license plate bracket (as
shown) in order to clear the mesh grille.
33. Reinstall the front license plate bracket reusing the upper center
factory screw.
34. Using a 7/64” drill bit, drill mounting holes through the portion of
the factory license plate bracket mounting tabs and into the
bumper cover.
35. Install the supplied #8 x 1/2” black truss head screws to finish
securing the front license plate mounting bracket.
36. Screw installation close-up. 37. Peel off the protective covering from the stainless steel mesh
surrounds. Use a mild solvent and a soft, clean cloth to remove
any glue residue. Use alcohol or glass cleaner and a soft clean
cloth to remove any solvent residue.
38. Finished installation.
33
34 35
36
8/8/2019 11 Up Honda Accord Coupe Grille Installation Manual Carid
http://slidepdf.com/reader/full/11-up-honda-accord-coupe-grille-installation-manual-carid 7/7
E&G Classics Warranty Information: E&G Classics, Inc. warrants its chrome parts and products to be free from defects in ma-
terial, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G.
This warranty is limited to the repair or replacement, at E&G Classics option, of the defec-
tive part or product. Full E&G Classics warranty information is available online @www.egclassics.com. Just click on the product warranty icon.
For E&G Classic Product Returns: Please contact the authorized E&G Classics Dealer where you purchased our prod-
uct from in regards to any workmanship or warranty claims. All items returned to
E&G Classics must have a return authorization number issued by us for inspection
or a defective product and or warranty issue. All merchandise sent back to E&G
Classics without proper paperwork or authorization will be rejected and returned.
Quanity: Description: Part Number:
1 Upper Mesh Grille - Complete ****************
1 Lower Mesh Surround 1124-0022-11
1 Lower Mesh Section 1124-0021-11
1 Installation Hardware Kit 1124-1902-11
1 Upper Grille Lower Hole Template 1124-0067-11
1 Emblem Mounting Plate 1110-0158-08X
14 Large Black Plastic Washers 1999-0264-00
12 #8-32 ESNA Half Nuts 1999-0065-00
1 Upper Grille Upper Hole Template 1124-0039-11
2 #10 S.S. lock Washers 1999-9555-00
2 #8-32 S.S. Hex Nuts 1999-9072-00
12” .045” x 1/4” Double Faced Tape 3004-9250-92
5 #8 x 1-1/4” Black Cap Plugs 1999-0311-00
Part #1124-0102-11
Copyright 2010 by E&G Classics, Inc. Visit us online today at www.egclassics.com