PUBLISHED: 11-MAY-20112008.25 X250, 303-12

INTAKE AIR DISTRIBUTION AND FILTERING - V8 S/C 4.2L PETROL

SUPERCHARGER (G1060825)

REMOVAL AND INSTALLATION

18.50.15SUPERCHARGER

ASSEMBLY - RENEW

4200 CC, AJ V8,

SUPERCHARGED4.7 USED WITHINS

REMOVAL

NOTE:

Removal steps in this procedure may contain installation details.

Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General

Procedures).

1.

Refer to: Cooling System Draining, Filling and Bleeding (303-03 Engine Cooling - 3.0L,

General Procedures).

2.

Refer to: Cowl Vent Screen (501-02 Front End Body Panels, Removal and Installation).3.

Refer to: Supercharger Outlet Pipe (303-12 Intake Air Distribution and Filtering - 4.2L,

Vehicles With: Supercharger, Removal and Installation).

4.

Refer to: Exhaust Manifold to Exhaust Gas Recirculation Valve Tube - V8 N/A 4.2L Petrol

(303-08 Engine Emission Control - 4.2L, Removal and Installation).

5.

Torque: 25 Nm

6.

7.

8.

9.

10.

Torque: 10 Nm

11.

Rotate the drive belt tensioner clockwise. Use a 1/2 inch square drive bar to rotate the

drive belt tensioner.

12.

13.

14.

15.

16.

17.

Torque: 8 Nm

18.

Torque: 25 Nm

19.

Torque: 25 Nm

20.

Torque: 25 Nm

21.

22.

Torque: 25 Nm

23.

INSTALLATION

To install, reverse the removal procedure.1.

PUBLISHED: 11-MAY-20112008.25 X250, 501-02

FRONT END BODY PANELS

COWL VENT SCREEN (G979342)

REMOVAL AND INSTALLATION

76.10.01

PLENUM CHAMBER

FINISHER - RENEW

ALL DERIVATIVES

0.4 USED WITHINS

CAUTION:

Always protect paintwork and glass when removing exterior components.

REMOVAL

NOTE:

Removal steps in this procedure may contain installation details.

For additional information, refer to: Windshield Wiper Pivot Arm (501-16, Removal and

Installation).

1.

2.

3.

4.

5.

INSTALLATION

To install, reverse the removal procedure.1.

PUBLISHED: 11-MAY-20112008.25 X250, 303-08

ENGINE EMISSION CONTROL - V8 N/A 4.2L PETROL/V8 S/C 4.2L PETROL

EXHAUST MANIFOLD TO EXHAUST GAS RECIRCULATION VALVE TUBE - V8 N/A 4.2L PETROL (G1060624)

REMOVAL AND INSTALLATION

17.45.11

EGR SYSTEM VALVE

TRANSFER PIPE - RENEW

4200 CC, AJ V8,

NATURALLY ASPIRATED

1.6 USED WITHINS

17.45.11

EGR SYSTEM VALVE

TRANSFER PIPE - RENEW

4200 CC, AJ V8,

SUPERCHARGED3.2 USED WITHINS

REMOVAL

Disconnect the battery ground cable. For additional information, refer to: Battery Disconnect

and Connect (414-01, General Procedures).

1.

Remove the engine cover. For additional information, refer to: Engine Cover - V8 N/A 4.2L

Petrol (501-05, Removal and Installation).

2.

Remove the intake manifold. For additional information, refer to: Intake Manifold (303-01, In-

vehicle Repair).

3.

4.

Remove the exhaust gas recirculation (EGR) valve inlet tube.

Remove and discard the gasket.

INSTALLATION

To install, reverse the removal procedure.1.

Tighten to 21 Nm.

2.

Install a new gasket.

PUBLISHED: 02-MAR-20172008.25 X250, 414-01

BATTERY, MOUNTING AND CABLES

BATTERY DISCONNECT AND CONNECT (G1033944)

GENERAL PROCEDURES

DISCONNECT

NOTE:

If a new battery is installed, the battery monitoring system (BMS) must be reset using Jaguar

approved diagnostic equipment.

Refer to: Battery and Battery Charging Health and Safety Precautions (100-00 General

Information, Description and Operation).

1.

Obtain and record the audio unit preset radio frequencies.2.

3.

4.

NOTE:

Where fitted.

CAUTION:

Take extra care not to damage the wiring harness.

5.

6.

CAUTION:

Make sure that the battery negative cable does not move when detaching the negative

terminal from the battery.

7.

CONNECT

CAUTION:

Make sure that the battery negative cable to the body retaining bolt is not loose and

fully tightened.

Torque: 13 Nm

1.

Torque: 6 Nm

2.

3.

4.

NOTE:

Make sure that both the positive and negative battery terminals are correctly located.

5.

NOTE:

Where fitted.

PUBLISHED: 11-MAY-20112008.25 X250, 303-12

INTAKE AIR DISTRIBUTION AND FILTERING - V8 S/C 4.2L PETROL

SUPERCHARGER OUTLET PIPE (G1060826)

Using Jaguar approved diagnostic equipment, reset the battery monitoring system (BMS).

6.

NOTE:

This step is only necessary when installing a new battery.

Refer to: Door Window Motor Initialization (501-11 Glass, Frames and Mechanisms, General

Procedures).

7.

Enter the audio unit preset radio frequencies.8.

Reset the clock to the correct time.9.

Start the engine and allow to idle until the engine reaches normal operating temperature.10.

Switch the engine off.11.

REMOVAL AND INSTALLATION

REMOVAL

NOTE:

Removal steps in this procedure may contain installation details.

Refer to: Engine Cover - V8 S/C 4.2L Petrol (501-05 Interior Trim and Ornamentation,

Removal and Installation).

1.

Refer to: Air Cleaner Outlet Pipe (303-12E, Removal and Installation).2.

3.

4.

5.

6.

Torque: 9 Nm

7.

Torque: 9 Nm

8.

Torque: 8 Nm

9.

INSTALLATION

To install, reverse the removal procedure.1.