Post on 06-Feb-2018
To order the highest quality flawed specimens call: (704) 795-4401 or visit www.flawtech.com
~ The World Leader in Manufacturing Real Flaws ~
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
2006
TABLE OF CONTENTS
FLAWED SPECIMEN CATEGORIES
PDI ALTERNATIVE ASME CAL BLOCKS
EPRI CS-4774 & BASIC PIPING CAL BLOCKS
PDI UT 10 CALIBRATION BLOCK SET
OVERLAY STEP WEDGE CAL BLOCK
RENTAL PRICE LIST APPENDIX VIII
RENTAL PRICE LIST STANDARD KITS
RENTAL PRICE LIST ADVANCED KITS
FLAWTECH PRICE LIST
..............................
.................................
...............................................
.................................
.....................................
..............................................
...............................................
..............................
.............................
.............................
........................
................
............................................
..............................................
...........................................
.......................
..................................
.....................................
........................
......................
.........
........................
..........................
.................................
................................
...........................
........................
........................
................................................
STANDARD KIT INTRODUCTION
DISCONTINUITIES LIST
STANDARD RADIOGRAPHIC KIT
STANDARD ULTRASONIC KIT
STANDARD MAGNETIC PARTICLE &
LIQUID PENETRANT KIT
STANDARD VISUAL KIT
STANDARD DEMONSTRATION KIT
PRACTICAL EXAM INTRODUCTION
UT PRACTICAL EXAM SPECIMENS
MT/PT PRACTICAL EXAM SPECIMENS
SAMPLE DRAWING OF EXAM SPECIMENS
ADVANCED SPECIMENS
API-UT-1 SPECIMEN KIT
AWS / CWI SPECIMEN KIT
ASME SECTION XI, APPENDIX VII KIT
ASME SECTION XI, APPENDIX VIII
SUPPLEMENTS 2, 3 & 10 KITS
FLAW IMPLANT TECHNIQUES
ULTRASONIC CALIBRATION BLOCKS
NASA/GENERAL DYNAMICS SERIES
PROGRAMMED INSTRUCTION &
CLASSROOM TRAINING BOOKS
APPENDIX VIII PRACTICE SESSIONS &
APPENDIX VIII QUALIFICATIONS
PH DIVERSIFIED INC.
INQUAL DIVISION
PAGE 1
PAGE 2
PAGE 3
PAGE 4
PAGE 5
PAGE 6
PAGE 7
PAGE 8
PAGE 9
PAGE 10
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 15
PAGE 16
PAGE 17
PAGE 18
PAGE 19
PAGE 20
PAGE 21
PAGE 22
PAGE 23
PAGE 24
PAGE 25
PAGE 26
PAGE 27
PAGE 28
PAGE 29, 30
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
FLAWED
SPECIMEN
CATEGORIES
STANDARD ADVANCED CRITICAL
STANDARD SPECIMENS:
Have a tolerance of
+/- 0.150” (4mm).
Includes all standard kit
specimens and all ut &
mt/pt practical exam
specimens.
Designed to enhance the
training & qualification
of level I & II personnel
with regards to
snt-tc-1a, en473 & pcn.
Normally less expensive
than advanced and
critical specimens.
Basic document package
with cad drawings is
Included with each kit
or exam specimen.
Custom specimens are
available at this level of
tolerance.
ADVANCED SPECIMENS:
Have a tolerance of
+/- 0.080” (2mm)
Includes all advanced
specimens, api-ut-1 kit &
all asme section xi
appendix vii specimen bank.
Designed to enhance the
training & qualification
of level I, II & III
personnel with regards to
snt-tc-1a, en473 & pcn.
Are larger in size than
the standard specimen
and higher tolerance.
Stock Advanced Specimens
are designed with specific
flaw types and geometry.
Document package with
cad drawings is included
with each kit or individual
advanced specimen.
Custom specimens are
available at this level of
tolerance.
CRITICAL SPECIMENS:
Have a tolerance of
+/- 0.040” (1mm)
Includes all asme section
xi appendix viii specimens
and most of the custom
designed specimens.
Designed to customer
specifications for their
specific training &
qualification of ndt
personnel and
procedures.
Size of specimens
range from a small bolt
for the space shuttle to
a 20,000 pound reactor
nozzle.
Detailed document
package is included with
each specimen.
Contact a member of
FlawTech for more
details.
All specimens in this
category are custom
specimens.
INDUSTRIES THAT USE FLAWTECH SPECIMENS
CALL FLAWTECH TODAY FOR DETAILS
SPECIMENS
RECOGNIZED
GLOBALLY
NDT
INDUSTRY
PIONEER
UNSURPASSED
QUALITY
STANDARD KIT
INTRODUCTION
FLAWTECH STANDARD KITS
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
RT KIT
UT KIT
MT/PT KIT
VT KIT
DEMONSTRATION KIT
REFERENCE RADIOGRAPHS
5 SPECIMENS & 11 FLAWS
FILM ONLY - 16 RADIOGRAPHS SHOWING 20 REAL FLAWS
SPECIAL
KITS
INDUSTRIES THAT USE FLAWTECH SPECIMENS
20 “REAL” FLAWS PER KIT
10 LARGE 4” X 8”
CARBON STEEL
SPECIMENS PER KIT
“FREE” CARRYING CASE
DETAILED DOCUMENT
PACKAGE WITH CAD
DRAWINGS
Flaw Manufacturing Technology
FLAWTECH STANDARD
KIT SPECIMENS
ARE DESIGNED TO:ENHANCE THE TRAINING &
QUALIFICATION OF LEVEL I & II
PERSONNEL WITH REGARDS TO
SNT-TC-1A, EN473 & PCN.
ASSIST WITH BASIC FLAW
DETECTION, SIZING AND
INTERPRETATION USING COMMON
WELD GEOMETRIES AND FLAW
TYPES.
2
REV. 10-05
CUSTOM KITS AVAILABLE
EACH KIT CONTAINS
FLAWTECH
DISCONTINUITIES
LIST4486 RACEWAY DR
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing Technology
# FLAW TYPE WELD NDT METHOD
10
11
12
13
14
15
16
17
18
19
20
30
31
32
33
34
35
36
37
38
39
50
51
52
53
54
55
56
57
58
59
70
71
72
73
74
75
76
77
78
79
80
90
91
92
93
TOE CRACK
TOE CRACK
ROOT CRACK
UNDERBEAD CRACK
CENTER LINE CRACK (SURFACE)
CENTER LINE CRACK (SUB-SURFACE)
CIRCUMFERENTIAL CRACK (FLUSH CROWN)
TRANSVERSE CRACK (FLUSH CROWN)
BASE METAL CRACK (CROWN HAZ AREA)
BASE METAL CRACK (ROOT HAZ AREA)
CRATER CRACK (CROWN STOP/START AREA)
POROSITY (SUB-SURFACE)
POROSITY (SUB-SURFACE)
POROSITY (SURFACE)
POROSITY (SURFACE)
SINGLE GAS PORE
SINGLE GAS PORE
SLAG INCLUSION (ROOT AREA)
SLAG INCLUSION (WELD GROOVE AREA)
SLAG INCLUSION (ROOT AREA)
TUNGSTEN INCLUSION (ROOT AREA)
LAMINATION (BASE METAL)
LAMINATION (BASE METAL)
LACK OF FUSION (SUB-SURFACE)
LACK OF FUSION (SURFACE BREAKING)
LACK OF FUSION (SURFACE BREAKING)
LACK OF FUSION (ROOT AREA)
INCOMPLETE ROOT PENETRATION
INCOMPLETE ROOT PENETRATION
INCOMPLETE ROOT PENETRATION (BRIDGING)
INCOMPLETE GROOVE WELD (CROWN AREA)
ROOT CONCAVITY
EXCESS ROOT PENETRATION
MISALIGNMENT (ROOT & CROWN AREA)
UNEVEN LEG LENGTH
EXCESS CROWN
EXCESS CROWN
CONCAVE CROWN
CONCAVE CROWN
UNDERCUT
UNDERCUT
OVERLAP
WELD SPATTER
WELD SPATTER
CHIPPING HAMMER MARKS
CHIPPING HAMMER MARKS
SV / DV
FILLET
SV
FILLET
SV / DV
SV / DV
SV / DV
SV / DV
SV / DV
SV
SV / DV
SV / DV
FILLET
SV / DV
FILLET
SV / DV
FILLET
SV
SV / DV
FILLET
SV / DV
SV
WP FACE
SV / DV
SV / DV
FILLET
SV
SV
DV
FILLET
SV / DV
SV
SV
SV
FILLET
SV / DV
FILLET
SV / DV
FILLET
SV / DV
FILLET
FILLET
SV / DV
FILLET
SV / DV
FILLET
-
-
-
-
-
-
-
-
-
-
VT
-
-
VT
VT
-
-
-
-
-
-
-
-
-
-
-
-
VT
-
-
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
VT
MT/PT
MT/PT
MT/PT
-
MT/PT
-
MT/PT
MT/PT
MT/PT
MT/PT
MT/PT
-
-
MT/PT
MT/PT
-
-
-
-
-
-
-
MT/PT
-
MT/PT
MT/PT
MT/PT
MT/PT
-
-
MT/PT
-
-
-
-
-
-
-
-
-
-
MT/PT
-
-
-
-
UT
UT
UT
UT
UT
UT
UT
UT
UT
UT
-
UT
UT
-
-
UT
-
UT
UT
UT
-
UT
-
UT
UT
-
UT
UT
UT
UT
UT
-
-
-
-
-
-
-
-
-
-
-
VT
VT
VT
VT
RT
-
RT
-
RT
RT
RT
-
-
-
-
RT
RT
-
-
RT
RT
RT
RT
RT
RT
-
-
-
-
-
-
RT
RT
-
RT
RT
RT
RT
-
-
-
-
-
-
-
-
RT
RT
RT
-
HOW TO REQUEST A CUSTOM SPECIMEN
1ST
SELECT A TOLERANCE
Standard +/-0.150” (4mm)
Advanced +/-0.080” (2mm)
Critical +/-0.040” (1mm)
1ST
SELECT A TOLERANCE
Standard +/-0.150” (4mm)
Advanced +/-0.080” (2mm)
Critical +/-0.040” (1mm)
2ND
SELECT YOUR FLAWS
FROM THE ABOVE TABLE
OR SPECIFY YOUR
SPECIAL REQUIREMENTS
2ND
SELECT YOUR FLAWS
FROM THE ABOVE TABLE
OR SPECIFY YOUR
SPECIAL REQUIREMENTS
3RD
SELECT THE MATERIAL
TYPE, WELD PREP GEOMETRY
AND THE REQUIRED NDT
METHOD OF INSPECTION
3RD
SELECT THE MATERIAL
TYPE, WELD PREP GEOMETRY
AND THE REQUIRED NDT
METHOD OF INSPECTION
12. Root Crack in Single VeeMT/PT, UT, RT
15. Centerline Crack, SingleVee (sub-surface)UT, RT
30. Porosity in Double Vee(sub-surface) UT, RT
31. Porosity in Fillet(sub-surface) UT, RT
34. Single Gas Pore in SingleVee UT, RT
36. Slag Inclusion in Single Vee(root area) UT, RT
37. Slag Inclusion in Single Vee(weld groove area) UT, RT
38. Slag Inclusion in Fillet(root area) UT, RT
39. Tungsten Inclusion in SingleVee (root area) RT
56. Incomplete Root Penetrationin Single Vee, VT, UT, RT
57. Incomplete Root Penetration inDouble Vee, UT, RT
59. Incomplete Groove Weld(crown area)VT, MT/PT, UT, RT
70. Root Concavity in SingleVee VT, RT
71. Excess Root Penetrationin Single Vee VT, RT
72. Misalignment, Root & Crownin Single Vee VT, RT
90. Weld Spatter on Single VeeVT, RT
92. Chipping Hammer Markson Single Vee, VT, RT
STANDARDRADIOGRAPHIC
KIT
Broc-RT-A 10/05
Shipping Weight 70lbs
0.375" & 0.625"(9.5mm & 16mm)
CROSS SECTION VIEW
REFERENCE EDGE
I.D. LABEL 8"(200mm)
4"(100mm)
4.5"(114mm)
0.337"(8.6mm)
8"(200mm)
I.D. LABELREFERENCE DATUM
CROSS SECTIONVIEW
CROSS SECTION VIEWREFERENCE EDGE
I.D.LABEL
8"(200mm)
4"(100mm)
4"(100mm)
0.375"(9.5mm)
The Radiographic Kit contains:8 Plates, 1 Pipe and 1 Tee20 Discontinuities, "REAL FLAWS", randomly placed
Actual X-Ray film is provided for each specimen. Specimensare packaged in 2 FREE CARRYING CASES. Complete withDocument Package with "Flaw Truth" documented by CADdrawings with a Standard Tolerance of ±0.150" (4mm).
The standard Radiographic Examination Kit contains 20 flawssimilar to those shown in the cross section drawings below. Also AvailableReference Radiograph Set "Real Film & Real Flaws"Document Package Only - with 10 CAD Drawings & 16 film
See current Price List for price information
30. Porosity in Single VeeRT, UT
14. Centerline Crack, SingleVee (surface breaking)MT/PT, UT, RT
4486 RACEWAY DRCONCORD, NORTH CAROLINA USA 28027Phone: 704-795-4401 FAX: 704-795-4403www.FlawTech.com
CONTACT YOUR LOCAL NDTSUPPLIER OR
FLAWTECH FOR ORDERING DETAILS
ALL SPECIMENS CONTAIN"REAL FLAWS"
Broc-UT-A 10/05
Shipping Weight 70lbs
0.375" & 0.625"(9.5mm & 16mm)
CROSS SECTION VIEW
REFERENCE EDGE
I.D. LABEL 8"(200mm)
4"(100mm)
4.5"(114mm)
0.337"(8.6mm)
8"(200mm)
I.D. LABELREFERENCE DATUM
CROSS SECTIONVIEW
CROSS SECTION VIEWREFERENCE EDGE
I.D.LABEL
8"(200mm)
4"(100mm)
4"(100mm)
0.375"(9.5mm)
34. Single Gas Pore in SingleVee UT, RT
37. Slag Inclusion in Single Vee(weld groove area) UT, RT
38. Slag Inclusion in Fillet(root area) UT, RT
50. Lamination in Single Vee(base metal) UT 52. Lack of Fusion in Single Vee
(crown area) UT
17. Transverse Crack in SingleVee, flush crownMT/PT, UT
18. Base Metal Crack in SingleVee (top HAZ area)MT/ PT, UT
19. Base Metal Crack in SingleVee (bottom HAZ area)MT/PT, UT
30. Porosity in Double Vee(sub-surface) UT, RT
31. Porosity in Fillet(sub-surface) UT, RT
DrawingsNot toScale
57. Incomplete Root Penetration inDouble Vee, UT, RT
59. Incomplete Groove Weld(crown area)VT, MT/PT, UT, RT
55. Lack of Fusion in Single Vee(surface breaking at root)MT/PT, UT
56. Incomplete Root Penetrationin Single Vee, VT, UT, RT
15. Centerline Crack, Single Vee(sub-surface) UT, RT
16. Circumferential Crack inSingle Vee, flush crownMT/PT, UT
10. Toe Crack in Single VeeMT/PT, UT
12. Root Crack in Single VeeMT/PT, UT, RT
The Ultrasonic Kit contains:8 Plates, 1 Pipe and 1 Tee20 Discontinuities, "REAL FLAWS", randomly placed
Specimens are packaged in 2 FREE CARRYING CASES.Complete with Document Package with "Flaw Truth" documentedby CAD drawings with a standard tolerance of ±0.150" (4mm).
The standard Ultrasonic Examination Kit contains 20 flaws similarto those shown in the cross section drawings below.
See current Price list for price information
4486 RACEWAY DR.CONCORD, NORTH CAROLINA USA 28027TEL: 704-795-4401 FAX: 704-795-4403www.FlawTech.com
CONTACT YOUR LOCAL NDTSUPPLIER OR
FLAWTECH FOR ORDERING DETAILS
ALL SPECIMENS CONTAIN"REAL FLAWS"
STANDARDULTRASONIC
KIT
STANDARDMAGNETIC PARTICLELIQUID PENETRANT
KIT
Drawings Not to Scale
80. Overlap in FilletVT, MT/PT
55. Lack of Fusion in Single Vee(surface breaking at root)MT/PT, UT
10. Toe Crack in Single VeeMT/PT, UT
12. Root Crack in Single VeeMT/PT, UT, RT
14. Centerline Crack, Single Vee(surface breaking)MT/PT, UT, RT
11. Toe Crack in FilletMT/PT, UT
The MT/PT Kit contains:8 Plates and 2 Tees20 Discontinuities , "REAL FLAWS", randomly placed
Specimens are packaged in a FREE CARRYING CASE .Complete with Document Package with "Flaw Truth" documentedby CAD drawings with a standard tolerance of +/- 0.150" (4mm).
The standard MT/PT Kit contains 20 "real" flaws similar to thoseshown in the cross section drawings below.
See current Price List for price information
CROSS SECTION VIEW
REFERENCE EDGE
I.D. LABEL 8"(200mm)
4"(100mm)
0.25"(6mm)
CROSS SECTION VIEWREFERENCE EDGE
I.D.LABEL
8"(200mm)
4"(100mm)
4"(100mm)
0.25"(6mm)
Broc-MT-A 10/05
16. Circumferential Crack inSingle Vee, flush crownMT/PT, UT
17. Transverse Crack in SingleVee, flush crownMT/PT, UT
18. Base Metal Crack in SingleVee (top HAZ area)MT/ PT, UT
19. Base Metal Crack in SingleVee (bottom HAZ area)MT/PT, UT
20. Crater Crack in Single Vee(surface stop-start area)MT/PT, VT
32. Porosity in Single Vee(surface breaking)VT, MT/PT
33. Porosity in Fillet(surface breaking)VT, MT/PT
51. Lamination in Weld PrepMT/PT
53. Lack of Fusion in Single Vee(surface breaking at crown)MT/PT, UT
54. Lack of Fusion in Fillet(surface breaking at crown)MT/PT
4486 RACEWAY DR.CONCORD, NORTH CAROLINA USA 28027TEL: 704-795-4401 FAX: 704-795-4403www.FlawTech.com
CONTACT YOUR LOCAL NDTSUPPLIER OR
FLAWTECH FOR ORDERING DETAILS
ALL SPECIMENS CONTAIN"REAL FLAWS"
STANDARDVISUAL
KIT
33. Porosity in Fillet(surface breaking)VT, MT/PT
32. Porosity in Single Vee(surface breaking)VT, MT/PT
20. Crater Crack in Single Vee(surface stop-start area)MT/PT, VT
The Visual Kit contains:7 Plates and 3 Tees20 Discontinuities, "REAL FLAWS", randomly placed
Specimens are packaged in a FREE CARRYING CASE .complete with Document Package with "Flaw Truth" documentedby CAD drawings with a standard tolerance of +/- 0.150" (4mm).
The standard Visual Examination Kit contains 20 flaws similar tothose shown in the cross section drawings below.
See current Price List for prices information
CROSS SECTION VIEW
REFERENCE EDGEI.D.
LABEL
8"(200mm)
4"(100mm)
4"(100mm)
0.25"(6mm)
91. Weld Spatter on FillerVT, RT
Broc-VT-A 2/03
Drawings Not to Scale
72. Misalignment, Root & Crownin Single Vee VT, RT
71. Excess Root Penetrationin Single Vee VT, RT
70. Root Concavity in Single VeeVT, RT
56. Incomplete Root Penetrationin Single Vee, VT, UT, RT
59. Incomplete Groove Weld(crown area)VT, MT/PT, UT, RT
90. Weld Spatter on Single VeeVT, RT
80. Overlap in FilletVT, MT/PT
79. Undercut in FilletVT
78. Undercut in Single VeeVT
77. Concave Crown in FilletVT
76. Concave Crown in Single VeeVT
75. Excess Crown in FilletVT
74. Excess Crown in Single VeeVT
73. Uneven Leg Length in FilletVT
CONTACT YOUR LOCAL NDTSUPPLIER OR
FLAWTECH FOR ORDERING DETAILS
4486 RACEWAY DR.CONCORD, NORTH CAROLINA USA 28027TEL: 704-795-4401 FAX: 704-795-4403www.FlawTech.com
CROSS SECTION VIEW
REFERENCE EDGE
I.D.LABEL
8"(200mm)
4"(100mm)
0.25"(6mm)
ALL SPECIMENS CONTAIN"REAL FLAWS"
NDTDEMONSTRATION
KIT
APPLICABLE NDTMETHOD UT RT MT PT VT
11 - Toe Crack (fillet)15 - Center Line Crack
19 - Base Metal Crack
30 - Porosity (single vee)
20 - Crater Crack
37 - Slag Inclusion54 - Lack of Fusion
71 - Excess Root
X X X
X X XX X X
XXX X
XXX
X
The NDT Demonstration Kit contains:1 Pipe, 3 Plates and 1 Tee11 Discontinuities, "REAL FLAWS", randomly placed
Specimens are packaged in a FREE CARRYING CASE. The"Flaw Truth" is documented on CAD drawings with a standardtolerance of +/- 0.150" (4mm).
This Kit contains actual X-Ray film for RT specimens and a"Flaw Locator" for UT specimens.
This standard NDT Demonstration Kit contains 11 flaws in 5specimens. The flaws in these specimens can be examined byseveral different NDT methods to demonstrate the advantagesand disadvantages of each NDT method. See Kit Price List forcost and listings of other flaw types available only from FlawTech.
CROSS SECTION VIEW
REFERENCE EDGE
I.D. LABEL 8"(200mm)
4"(100mm)
0.25" & 0.625"(6mm & 16mm)
4.5"(114mm)
0.337"(8.6mm)
8"(200mm)
I.D. LABELREFERENCE DATUM
CROSS SECTIONVIEW
CROSS SECTION VIEW
REFERENCE EDGE
I.D.LABEL
8"(200mm)
4"(100mm)
4"(100mm)
0.25"(6mm)
Drawings Not to Scale
See current Price List for price information
11. Toe Crack in FilletMT/PT, UT
19. Base Metal Crack in rootHAZ. MT/PT, UT
Broc-Demo-A 10/05
FlawTech Inc.4486 RACEWAY DR.
CONCORD, NC 28027TEL: 704-795-4401FAX: 704-795-4403
www.FlawTech.com
57 - Incomplete Root
X XX
57. Incomplete Root Penetrationin Double Vee, UT, RT
30. Porosity in Single Vee(sub-surface) UT, RT
37. Slag Inclusion in SingleVee, UT, RT
54. Lack of Fusion in Fillet (surface breaking) MT/PT
71. Excess Root in Single Vee RT, VT
20. Crater Crack (crown stop-start area) MT/PT, VT
15. Center Line Crack in Double Vee (sub-surface) UT, RT
32 - Porosity (surface) X X XX X
32. Porosity in Single Vee(surface) VT, MT/PT
18. Base Metal Crack in Single Vee MT/ PT, UT
18 - Base Metal CrackX X
Demonstration Kit Flaw and Weld Prep Cross Sections
UT & MT/PT PRACTICAL
EXAM SPECIMENS
UT PRACTICAL
EXAM SPECIMENS
MT/PT PRACTICAL
EXAM SPECIMENS
12 TO CHOOSE FROM
3 FLAWS PER SPECIMEN
12 TO CHOOSE FROM
3 FLAWS PER SPECIMEN
LARGER THAN STANDARD
KIT SPECIMENS
CUSTOMIZE YOUR SET
PURCHASE 1,2, 3 OR 12
BUY 3 OR MORE AND
RECEIVE 10% OFF &
A “FREE” CASE
CUSTOM EXAM SPECIMENS
AVAILABLE UPON REQUEST
SEE UT & MT/PT PRACTICAL EXAM BROCHURES
FOR MORE DETAILS
INDUSTRIES THAT USE FLAWTECH SPECIMENS
FLAWTECH PRACTICAL
EXAM SPECIMENS
ARE DESIGNED TO:ENHANCE THE TRAINING &
QUALIFICATION OF LEVEL I & II
PERSONNEL WITH REGARDS TO
SNT-TC-1A, EN473 & PCN.
ASSIST WITH BASIC FLAW
DETECTION, SIZING AND
INTERPRETATION USING COMMON
WELD GEOMETRIES AND FLAW
TYPES.
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyPRACTICAL EXAM
INTRODUCTION
9
REV.10-05
“NEW SPECIMENS”
AVAILABLE!
“NEW SPECIMENS”
AVAILABLE!
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
ULTRASONIC
PRACTICAL EXAM
SPECIMENS
visio ut broc 10/05
PLATES & SHEETS
P101
0.75" x 8" x 10" plate
BAR & ROD STOCK
P102
1.5" OD x 12"
BAR & ROD STOCK
P103
4" OD x 6"
L/R 90° ELBOW TO PIPE
P104
2" SCH160 (.344" wall)
NODE TO PLATE WELD
P105
2" SCH160 to .375" PLATE
PIPE TO SOCKET WELD
P106
2" SCH160 PIPE to COUPLING
WELDED PLATE
P108
1.0" x 6" x 10"
10
"
WELDED PLATE
P107
0.5" x 8" x 12"
8"
WELDED PIPING
P109
4.5" OD x 0.531" x 8"
FORGED PIPE FLANGE
P111
6" OD x 0.75" thick
WELDED TEE
P112
0.5" x 8" x 8" x 4"
LAP JOINT
P110
6"
0.5" x 12" x 6"
90°6"
6"8"
4"
8"
2"
12" 6"
12"
8"
� 3 Flaws per specimen
� "REAL FLAWS" in each specimen
� Document Package w/ each specimen
� Standard Tolerance +/- 0.150" (4mm)
� Blank Specimens available
� Specimens are carbon steel
� No Two Specimens are Alike
� Custom Specimens Available
� <10% for the Purchase of 3+
� FREE Carrying Case w/ 3+
� See Current Price List for Price
and Information
Specimen Details:
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
MT / PT
PRACTICAL EXAM
SPECIMENS
CAST FITTING
P001
2.0" to 1.3" reducer, 5" long
MACHINED SPINDLE
P002
1.75" diameter x 8"
BOLT & NUT
P003
1.25" OD x 6"
FORGED EYE HOOK
P004
6" long with 2" eye
FORGED SHACKLE & PIN
P005
4.25" with 0.75" pin
WELDED PLATE
P007
WELDED PIPING
P008
4.5" OD x 0.25" x 8"
FORGED PIPE FLANGE
P009
6" OD x 0.75" thick
WELDED TEE
P011
0.25" x 8" x 8" x 4"
PIPE to SOCKET WELD
P012
2" SCH160 PIPE to COUPLING
0.25" x 8" x 12"
2.75"
0.25" x 4"
FORMED METAL PLATE
P006
3"
MACHINED GEAR
P010
4.6" diameter x 1.5" bore
Top
ViewP0
01
End
View
Front
View
12"
4"
6"
2"
8"
Specimen Details:
� 3 Flaws per specimen
� "REAL FLAWS" in each specimen
� Each Specimen has Document Package
� Standard Tolerance +/- 0.15" (4mm)
� Blank Specimens available
� Specimens are carbon steel
� No Two Specimens are Alike
� Custom Specimens Available
� <10% for the Purchase of 3+
� FREE Carrying Case w/ 3+
� See Current Price List for Price
and Information
SAMPLEDRAW
ING
OF
PRACTICAL
&ADVANCED
SPECIMENS
THESE SPECIMENS ARE DESIGNED FOR:
TRAINING & QUALIFICATION OF LEVEL I & II PERSONNEL WITH REGARDS TO SNT-TC-1A, EN473 & PCN
FLAW DETECTION, SIZING & INTERPRETATION USING COMMON WELD GEOMETRIES AND FLAW TYPES.
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
INDUSTRIES THAT USE FLAWTECH SPECIMENS
ADVANCED SPECIMENSPLATES PIPES TEES Y’s NODES NOZZLES
PART SPECIMEN DIMENSIONS SPECIMEN
NUMBER TYPE (INCHES) DETAILS
UA-001 PLATE W/SV 0.5 X 12 X 12
UA-002 PLATE W/SV 0.75 X 12 X 12
UA-003 PLATE W/SV 1.0 X 12 X 16
UA-004 PLATE W/DV 1.25 X 12 X 17
UA-005 PIPE W/SV 6 SCH120 X 12
UA-006 PIPE W/SV 6 SCHXXH X 12
UA-007 PIPE W/SV 8 SCH80 X 12
UA-008 PIPE W/SV 12 SCH80s X 12
UA-009 PIPE W/SV 12 SCH120 X 12
UA-010 TEE W/SV 1.0 X 8 X 8 X 12
UA-011 TEE W/DV 1.0 X 8 X 8 X 12
UA-012 TEE W/DV 1.25 X 9 X 9 X 12
UA-013 Y-JOINT 1.25 X 9 X 9 X 12
UA-014 NODE & 10 SCH120 X 10
CARRIER 1.0 X 20 X 20
UA-015 NOZZLE & 8 SCH80 X 10
CARRIER 1.0 X 20 X 20
RA-001 PLATE W/SV 0.375 X 12 X 12
RA-002 PLATE W/DV 0.625 X 12 X 12
RA-003 PLATE W/SV 0.75 X 12 X 12
RA-004 PLATE W/SV 1.0 X 12 X 16
RA-005 PLATE W/DV 1.0 X 12 X 16
RA-006 PIPE W/SV 2 SCH80 X 12
RA-007 PIPE W/SV 6 SCH120 X 12
RA-008 PIPE W/SV 12 SCH80 X 12
MA-001 PLATE W/SV 0.375 X 12 X 12
MA-002 PIPE W/SV 6 SCH80 X 12
MA-003 PIPE W/SV 12 SCH40 X 12
MA-004 TEE W/SV 0.375 X 6 X 6 X 12
MA-005 Y-JOINT 0.375 X 6 X 6 X 12
MA-006 NODE & 10 SCH40 X 10
CARRIER 0.5 X 16 X 16
MA-007 NOZZLE & 8 SCH60 X 10
CARRIER 0.5 X 16 X 16
UT
UT
UT
UT
UT
UT
RT
RT
RT
MT/P
T&
VT
FLAWTECH
“THE GLOBAL
STANDARD”
ADVANCED
SPECIMENS
LARGER THAN OUR
PRACTICAL EXAM
SPECIMENS
ADVANCED
SPECIMENS
TOLERANCE+/- 0.080“
3 REAL FLAWS
PER SPECIMEN
RANDOMLY PLACED
COMPLETE
DOCUMENT PACKAGE
INCLUDED
CUSTOM SPECIMENS
AVAILABLE
UPON REQUEST
13
REV.10-05
SEE PRICE LIST
FOR PRICES
AND WEIGHTS
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyAPI-UT-1 FLAWED
SPECIMEN KIT
API-UT-1 QUALIFICATION SPECIMENS
API-UT-1KIT CONTAINS:
CUSTOM
AND
LEASE
OPTIONS
AVAILABLE
TOTAL OF
4
SPECIMENS
1 - 1.0” THICK PLATE W/ DOUBLE VEE (1” X 12” X 15”)
1 - 0.5” THICK PLATE W/ SINGLE VEE (0.5” X 10” X 12”)
1 - 8” SCH 80 PIPE (0.5” WALL X 12”, 360°)
1 - 12” SCH80 PIPE (0.688” WALL X 12”, 180° SEG.)
API KIT
STANDARD
FEATURES
- COMPLETE DOCUMENT PACKAGE W/ CAD DRAWINGS
- 3 “REAL” FLAWS PER SPECIMEN
- FLAWTECH ADVANCED TOLERANCE +/- 0.080”
- SPECIMENS ARE CARBON STEEL
API KIT
CUSTOM
OPTIONS
- 10% ID / OD CALIBRATION NOTCHES
- 0.75” X 4.5” X 6” ASME SEC. V BASIC CAL. BLOCK
- 8” SCH 80 (0.5” WALL) X 8” PIPE ASME SEC. V ANGLE
BEAM CAL. BLOCK
- RADIOGRAPHS
SEE PRICE LIST FOR PRICE INFORMATION
API KIT
STANDARD
FEATURES
FLAWTECH
ORIGINAL
KIT
“REAL FLAWS”USED IN KIT SPECIMENS
LACK OF PENETRATION
CENTER LINE CRACK
SLAG INCLUSION
LACK OF FUSION
ROOT CRACK
POROSITY
CUSTOM LOCKING STORAGE BOX
AVAILABLE UPON REQUEST
FOR UT EXAMINATION OF FERRITIC WELDS
14
REV.10-05
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyAWS / CWI FLAWED
SPECIMEN KIT
AWS / CWI TRAINING SPECIMENS
10
SPECIMENS
4 - TEES 4” X 6” X 2” X 0.25”
4 - PLATES 4” X 6” 0.25”
2 - EDGE & LAP JOINTS
4” X 6” X 0.3125”
2 FLAWS PER SPECIMEN
FLAW’S ARE RANDOMLY PLACED
FLAW’S ARE “BORDER LINE”
ACCEPTABLE OR REJECTABLE
CARBON STEEL SPECIMENS
WELDING PROCESS - SMAW
DOCUMENT PACKAGE W/ CAD DRAWINGS
“FREE” CARRYING CASE
DESIGNED SPECIFICALLY FOR
VISUAL WELD INSPECTION
TRAINING
AWS/CWI KIT
DESIGN
FEATURES
CUSTOM AND LEASE OPTIONS AVAILABLE
DESIGN SPECIFICATIONS BASED ON AWS D1.1
- UNDERCUT
- CRATER CRACK
- EXCESSIVE CONVEXITY
- UNDERSIZE LEG
- CLUSTER POROSITY
- ARC STRIKE
- OVERLAP
- LONGITUDINAL CRACK
- ALIGNED POROSITY
- INCOMPLETE PENETRATION
- EXCESSIVE REINFORCEMENT
- UNDERFILL
- CONCAVITY
- TRANSVERSE CRACK
- OVERSIZE LEG
AWS / CWI KIT FLAWS
AWS / CWI KIT FLAWS
REAL
FLAW
S
REAL
FLAW
S
REV.10-05
FLAWTECH
ORIGINAL
KIT
SEE PRICE LIST
FOR PRICE
INFORMATION
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
12"
10"
1.0"
12"
10"
0.5"
4.50"
2.375"
10.75"6.625"
ASME SECTION XI
APPENDIX VII KIT
CONTAINS 20
“REAL FLAWS”
8 PIECE
SPECIMEN SET
FOR TRAINING &
QUALIFICATION
FLAWTECH
ORIGINAL
KIT
SEE THE PRICE
LIST FOR PRICE
INFORMATION
SAMPLE OF “FLAW TRUTH” DOCUMENTATION
Z
-X +X
0.72"
(18mm)
each grid = 0.1" (2.5mm)
FLAW
FLAW
FLAW
FLAW
FLAWTECH HAS
REDESIGNED
THIS KIT TO BE
A COST
EFFECTIVE
SOLUTION
TO YOUR
TRAINING AND
QUALIFICATION
KIT DETAILSEACH SPECIMEN CONTAINS 2 TO 4 “REAL FLAWS”, DESIGNED TO MEET
APPENDIX VII SPECIFICATIONS.
SPECIMENS ARE MANUFACTURED TO FLAWTECH’S ADVANCED TOLERANCE
OF +/- 0.080”.
NO TWO SPECIMENS ARE ALIKE. BUY TWO SETS, ONE FOR TRAINING AND ONE
FOR TESTING.
DOCUMENT PACKAGE INCLUDES CAD DRAWINGS, CERTIFICATES OF CONFORMANCE
AND NDT REPORTS.
CUSTOM OPTIONS AVAILABLE SUCH AS 10% NOTCHES, BLANK SPECIMENS AND THE
PURCHASE OF INDIVIDUAL FLAWED SPECIMENS. CONTACT FLAWTECH FOR MORE DETAILS.
2 - WELDED PLATES 2 - WELDED PLATES 1 - WELDED PIPE
1 - WELDED PIPE 1 - WELDED PIPE 1 - WELDED PIPE
0.5” X 10” X 12” 1.0” X 10” X 12”
10” SCH160 X 12”
2” SCH160 X 12”
6” SCH160 X 12”4” SCH160 X 12”
ONE CARBON STEEL PLATE: #A7-CS-005
ONE STAINLESS PLATE: #A7-SS-005
ONE CARBON STEEL PLATE: #A7-CS-010
ONE STAINLESS PLATE: #A7-SS-010
ONE STAINLESS PIPE: #A7-SS-020
ONE CARBON STEEL PIPE: #A7-CS-100
(180° SEGMENT)
ONE CARBON STEEL PIPE: #A7-CS-100
(180° SEGMENT)
ONE CARBON STEEL PIPE: #A7-CS-100
(180° SEGMENT)
ONE STAINLESS PIPE: #A7-SS-060ONE CARBON STEEL PIPE: #A7-CS-040
16
REV.10-05
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
ASME SECTION XI
APPENDIX VIII KITS
ASME BOILER & PRESSURE VESSEL CODE, SECTION XI,
APPENDIX VIII, SUPPLEMENTS 2, 3 & 10 KITS
2” SCH80 X 24” 360°
4” SCH80 X 24” 360°
6” SCH160 X 24” 360°
12”SCH80s X 24” 360°
24”SCH80s X 24” 120°
KIT TOTAL - 5 SPECIMENS
1
3
4
9
5
22
1
1
2
3
3
10
2” SCH80 X 24” 360°
4” SCH80 X 24” 360°
6” SCH160 X 24” 360°
12”SCH80s X 24” 360°
24”SCH80s X 24” 120°
KIT TOTAL - 5 SPECIMENS
1
3
4
9
5
22
1
1
2
3
3
10
4” SCH80 X 24” 360°
6” SCH160 X 24” 360°
8” SCH80 X 24” 360°
12”SCH80s X 24” 180°
24”SCH80s X 24” 90°
KIT TOTAL - 5 SPECIMENS
3
4
6
4
4
21
2
2
3
4
4
15
PIPE SPECIMEN
DIMENSIONS
UNFLAWED
UNITS
FLAWED
UNITS
SUPPLEMENT 2
KIT FOR
AUSTENITIC
PIPING
SUPPLEMENT 3
KIT FOR
FERRITIC
PIPING
SUPPLEMENT 10
KIT FOR
DISSIMILAR
METAL WELDS
THE ABOVE KITS ARE MANUFACTURED TO MEET THE MINIMUM REQUIREMENTS
OF ASME, BOILER & PRESSURE VESSEL CODE, SECTION XI, APPENDIX VIII,
OF SUPPLEMENTS 2, 3 & 10.
KIT AND FLAW DETAILS:
EACH KIT WILL CONTAIN A MIX OF CROWN GEOMETRIES, SUCH AS, GROUND,
AS WELDED CROWNS AND WIDE CROWNS.
EACH KIT WILL CONTAIN NON-CRACK GEOMETRIC CONDITIONS.
ALL FLAWS WILL BE MECHANICAL FATIGUE OR THERMAL FATIGUE CRACKS.
AT LEAST 75% OF THE CRACKS WILL BE THERMAL FATIGUE.
10% OF THE FLAWS WILL BE ORIENTED AXIALLY & 30% FOR SUP.10.
50% OF THE CRACKS WILL BE COINCIDENT WITH FABRICATED CONDITIONS.
60% OF THE FLAW DEPTHS WILL BE MANUFACTURED AT 5-30%, 31-60 % AND
61-100% OF WALL THICKNESS. REMAINING 40% WILL HAVE RANDOM DEPTHS.
FLAWTECH
ORIGINAL
KIT
REV. 3-06
SEE PRICE LIST
FOR PRICE
INFORMATION
CRITICAL
TOLERANCE
+/- 0.040” (1MM)
4486 Raceway Dr. Concord, North Carolina USA 28027
Tel: 704.795.4401 Fax: 704.795.4403 Web: www.flawtech.com
Carbon Steel Stainless Steel
SS Clad
Stainless Steel
WeldSS Buttering
In-Situ Implants
Branched Thermal or
Mechanical Fatigue Crack
TYPICAL IN-SITU FATIGUE CRACK IMPLANT IN PIPING
Mechanical
Fatigue Crack
Mechanical Fatigue Crack in
Base Material & Cladding
In-Situ Implant
Excavation
Area
TYPICAL IN-SITU FATIGUE CRACK IMPLANTS IN VESSEL MATERIAL
Carbon Steel
Vessel
SS Clad
Carbon Steel Stainless Steel
SS Clad
Stainless Steel
Weld
SS
Buttering
Coupon
Implant
IGSCC or Thermal
Fatigue Crack
TYPICAL COUPON IMPLANT IN WELD MATERIAL
FLAW IMPLANT TECHNIQUES
FlawTech has the capability to use several methods to implant flaws
in a variety of configurations for nondestructive testing applications.
In the following data we have described a few of these methods so
you may gain a better understanding of our flaw manufacturing
possibilities.
In-Situ Implant- This technique has been the corner stone of flaw
manufacturing for many years and usually involves thermal or
mechanical fatigue cracks. The important characteristic is that the
flaw occurs in virgin base material (i.e. HAZ) so that UT energy can
impinge directly on the crack face without traveling through weld
metal. The process allows for precise mechanical dimensions of the
flaw face to be taken prior to implant. As shown below, this technique
allows the crack to be "branched" and this is the best way to replicate
the UT signal from IGSCC.
Coupon Implant- This process has the advantage of producing the
flaw in a small coupon in the laboratory and then implanting the
coupon into the mockup. The disadvantage is that precise mechanical
dimensions are usually not possible and the coupon is surrounded by
weld metal which may introduce additional UT reflectors.
Controlled Flaw- This is a unique proprietary process developed by
FlawTech to progressively extend a "crack-like" indication in any area
in carbon steel and within the weld groove in stainless steel or Inconel.
This process is often used in the production of "Dissimilar Metal"
specimens.
Weld-Solidification Crack- This technique is occasionally used
when a crack is desired within the weld groove. The weld is
"contaminated" by changing weld chemistry in a designated area to
produce a crack. Disadvantages include uncertainty about the
orientation and extent of cracking and crack size.
HIP (Hot Isostatic Process)- This technique is used to tighten the
tips of manufactured flaws. HIP is also used to tighten EDM Notches
in an effort to make them look like cracks. Disadvantages include
uncertainty as to how the grain structure of the base metal is effected
and the characteristics of the response to an EDM notch as well as
adding time and cost to the manufacturing process.
In addition to the aforementioned, FlawTech uses a variety of other
basic techniques for implanting slag, porosity, lack of fusion, under
bead cracking, etc. FlawTech offers 3 levels of tolerance; Standard
+/- 0.150", Advanced +/- 0.080" and Critical +/- 0.040", contact
FlawTech for more details.
4-STEP BLOCK
Thickness and linearity calibration. This 4-Step block comes in thicknesses
of .250”, .500”, .750”, and 1.000”. Step face measures .750”x.750”. In
accordance with ASTM E797. Two metric versions available.(4A and 4B)
NOTE: Variations of this block and the 5-Step block below are available if
additional steps are preferred. Also, larger step faces are offered for use
with large diameter transducers.
ULTRASONIC CALIBRATION BLOCKS
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyUT CALIBRATION
BLOCKS
5-STEP BLOCK
Thickness and linearity calibration. This 5-Step block comes in thicknesses
of .100”, .200”, .300”, .400 and .500”. Step face measures .750”x.750”. In
accordance with ASTM E797. Two metric versions available.(5A and 5B).
DSC Block
AWS-type clock used for shear wave distance and sensitivity calibration.
Contains a 1.0” radius opposite a 3.0” radius. The 3.0” radius includes a
.375” deep x .032” wide radius slot. Also contains a 0° reference point for
checking exit point on wedge, and a .125” diameter through hole and
corresponding markings at 45°, 60°, and 70° for measuring actual refracted
angle. In accordance with ASTM E164 and AWS 6.16.1B. Metric version
available. Special DSC blocks with radius scanning surfaces for NPS sizes
also offered. In Stock.
Dimensions: 1.000” thick x 4.000” long
AWS Resolution Block (RC Block)
Also called an RC Block, the AWS Resolution Reference Block is used for
checking resolution capabilities of angle beam transducers. Contains three
sets of .0625” diameter through-holes for 45°, 60°, and 70°. In accordance
with AWS Welding Highway and Railway Bridges specification D2.0-69, and
Structural Welding Code ANSI/AWS D1.1- 92. Metric version available. In
Stock.
Dimensions: 1.0"x3.0"x6.0”
DS Block
AWS-type block used for longitudinal distance and sensitivity calibration.
Contains a 2.0” high section between two 4.0” sections. In accordance with
AWS requirements.
Dimensions: 6.0”x4.0”x2.0”
19
Contact FlawTech for all your Standard and
Custom Calibration Block Needs
*all materials available upon request*
ULTRASONIC CALIBRATION BLOCKS
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyUT CALIBRATION
BLOCKS
All Blocks Available In: CS 1018, AL 7075-T6, & SS 304
*all other materials available upon request*
PDI ALTERNATIVE ASME CALIBRATION BLOCKS
The new PDI Alternative ASME blocks meet the requirements of the Performance Demonstration
Initiatice(PDI) Procedure No. PDI-UT-1, Rev. C, Fig. 4(Ferritic) and PDI-UT-2, Rev. C,
Fig.4(Austenitic). These cover the generic procedures for the ultrasonic examination of both ferritic
and austenitic pipe welds. The blocks offer users an economical alternative to fabricating multiple
curved cal blocks (pipe sections) in many diameters and wall thicknesses.
The blocks are normally supplied in sets of 3 individual blocks; one in A516 Grade 70 Steel, one in
Type 304/304L Stainless Steel, and one in Type 316/316L Stainless Steel. Individual blocks of any
one alloy are also offered.
Block design consists of steps(wall thicknesses) measuring 0.500", 1.000", 1.500", and 2.000".
Each step contains an EDM machined to a depth of 10% of wall x .010" wide x 2.0" long. Overall
block size is 2.00" wide x 2.25" tall x 10.00" long. The scanning and reflecting surfaces are
intentionally machined to simulate pipe and plate surfaces of 250 Ra maximum finish. Each block
is permanently machine-engraved on one edge to include the block description, serial no., alloy,
heat no., and FlawTech. The blocks are made from ultrasonically inspected, heat number-
traceable material supplied to FlawTech.
Contact FlawTech for all your Standard and
Custom Calibration Block Needs
*all materials available upon request*
ULTRASONIC CALIBRATION BLOCKS
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyUT CALIBRATION
BLOCKS
EPRI CS-4774 Basic Calibration Block
Used for establishment of primary reference responses for UT examination of welds. Block contains three axial SDHs
and two circ SDHs at 1.5" deep. Also contains one 1/8" diameter FBH at 0.5" deep and four notches at .031" deep x
.063" wide x 1.5" long. In accordance with EPRI CS-4774, Fig. A-3
ASME Sec. XI Basic Piping Calibration Block
Complete manufacture of the ASME Section XI Blocks including: supplying of pipe, machining of OD/ID(if needed),
cladding(if needed), machining of all notches and side-drilled holes(SDH), machine engraving of all essential info
including alloy, specification, diameter, wall thickness, and serial number. Blocks normally contain: one axial OD notch,
one axial ID notch, one circumferential OD notch, one circ ID notch, three axial SDHs at 1/4, 1/2, and 3/4T, and three
circ SDHs at 1/4, 1/2, and 3/4T. Can also be made from customer supplied material. We can upgrade your existing
blocks to Sec. XI requirements by adding needed holes and notches.
Contact FlawTech for all your Standard and
Custom Calibration Block Needs
*all materials available upon request*
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyUT CALIBRATION
BLOCKS
Contact FlawTech for all your Standard and
Custom Calibration Block Needs
*all materials available upon request*
PDI UT 10 CALIBRATION BLOCK SET
2” CIRC. BLOCK FOR ANGLES </= 50° 4” CIRC. BLOCK FOR ANGLES </= 50°
2” CONTOUR BLOCK FOR AXIAL SCANS 4” CONTOUR BLOCK FOR AXIAL SCANS
12 - 24 CONTOURED PROBE BLOCK 12” STAINLESS PIPE SEGMENT BLOCK
24” STAINLESS PIPE SEGMENT BLOCK
BLOCKS ARE BASED ON EPRI DESIGN
304 STAINLESS STEEL MATERIAL
BLOCKS MAY BE PURCHASED AS SET
OR INDIVIDUALLY
SEE PRICE LIST FOR PRICE
INFORMATION
OVERLAY STEP WEDGE
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing TechnologyUT CALIBRATION
BLOCKS
Contact FlawTech for all your Standard and
Custom Calibration Block Needs
*all materials available upon request*
STEP WEDGE IS BASED ON EPRI DESIGN FOR UTILITIES
CONTAINS 7 SDH’S, 5 FBH’S AND 5 EDM NOTCHES
BASE METAL AND OVERLAY SPECIFIED BY CUSTOMER
CONTACT FLAWTECH FOR MORE DETAILS AND PRICE INFORMTION
Revision of NASA/General Dynamics NDT Training Series
The Industry Standard for Basic NDT Training
Level I Programmed Instruction Handbooks
Author ISBN No. Editiion Order # New Low Price
Introduction to NDT Smilie 978-1-886630-00-0 1999 PI-1 $18.00
Liquid Penetrant Testing Smilie 978-1-886630-01-7 1998 PI-2 $18.00
Magnetic Particle Testing Smilie - 978-1-886630-22-2 2 Vol. Set 1997 PI-3 $32.00 Ultrasonic Testing Smilie - 978-1-886630-03-1 3 Vol. Set 1999 PI-4 $49.00
Eddy Current Testing Cox - 978-1-886630-21-5 2 Vol. Set 1997 PI-5 $32.00
Level II Classroom Training Handbooks Liquid Penetrant Testing Smilie 978-1-886630-14-7 1998 CT-2 $15.00 Magnetic Particle Testing Smilie 978-1-886630-15-4 1997 CT-3 $15.00 Ultrasonic Testing Smilie 978-1-886630-16-1 1995 CT-4 $15.00 Eddy Current Testing Cox 978-1-886630-17-8 1997 CT-5 $15.00
Level I-III McGraw Hill Reference Handbook Handbook of Nondestructive Evaluation – Hellier 978-0-07-028121-9 2001 REF-1 $99.00
This classic series of General Dynamics Programmed Instruction and Classroom Training Handbooks has been the standard of the NDT industry for many years and has been Updated with Current Technology and is now available from the publisher, PH Diversified, Inc. or your local NDT Supplier.
Level I - Programmed Instruction Handbooks This entry-level material is designed as self-study instruction with quizzes at the end of each chapter to reinforce learning. The "Introduction to NDT" book (PI-1) should be read prior to starting any of the other books in the series. Typically, it takes about 10-12 hours to complete each volume of Programmed Instruction (PI) text. Written examinations suitable for Level I-II qualifications are included in the PI series. Level II - Classroom Training Handbooks This material is an extension of the information taught in the corresponding Programmed Instruction Books, deleting some of the processing details and adding tabular matter and other technical details. These texts are best used in conjunction with classroom lectures after the student has completed the Programmed Instruction Books. Level I-III – Reference Handbook for NDE This McGraw Hill publication is the ideal complement to any NDT/NDE training program or reference library. The content was written and compiled by one of the master trainers in the NDT industry, Mr. Charles J. Hellier.
Buy Direct and Save: • 20% Discount for orders totaling 20 or more books. PH Diversified Inc. Publisher • Add only $5.00 to each order 4486 Raceway Drive # B for shipping and handling to Concord, NC 28027 the US only. Phone: 704-795-4402 • Intl. orders require Credit Fax: 704-795-4403 Card or a proforma invoice. Email: GPherigo@FlawTech.com • VISA, MC and AMEX
Next Day Shipping Possible www.FlawTech.com/PHD
Visio/pricelist\isi-inqual practice 10-05
Performance DemonstrationAPPENDIX VIII QUALIFICATIONS
1 person at INQUAL facility per 10 hour day. . . . . . . . . . . . . . . . .$ 1,300 2 people at INQUAL facility per 10 hour day. . . . . . . . . . . . . . . . .$ 1,6003-4 people at INQUAL facility per 10 hour day. . . . . . . . . . . . . . . . . $ 2,0005-6 people at INQUAL facility per 10 hour day. . . . . . . . . . . . . . . . . $ 2,700
INQUAL will review procedures, administer the Appendix VIII qualificationand provide full documentation in accordance with the ASME Code and theuser's "written program."
INQUAL's QA program complies with 10CFR50 and has been audited by NUPIC.
Contact INQUAL for a complete package of information.
PH Diversified, Inc.INQUAL Division...NDE Performance Demonstration and Qualification Services
Contact: Dr. George Pherigo, 4486-B Raceway Dr., Concord, NC 28027 Tel: 704-795-4402 Email: gpherigo@flawtech.com
APPENDIX VIII PRACTICE SESSIONS
Appendix VIII Hands-On Guided Practice Session
$195 per person with a minimum of three and a maximum of 6 people.Six (6) persons from the same company will cost $895.No charge for attendance of NDE instructor or PDI qualified administrator.
Specimen Lease for On-Site Practice Session
Basic Practice Session
1-2 people at INQUAL facility per 10 hour day. . . . . . . . . . . . . . $2903-4 people at INQUAL facility per 10 hour day. . . . . . . . . . . . . . $3805-6 people at INQUAL facility per 10 hour day. . . . . . . . . . . . . . $460
4 OPTIONS AVAILABLE
Individual or multiple specimens may be leased and shipped to your facility.Prices range from $75 to $125 a day plus freight cost.See "Rental Price List" for more information.
Includes: Unlimited access to INQUAL's specimen inventory
Includes: Unlimited access to INQUAL's specimen inventory One day of "Guided Practice Exercises" with a certificate to document compliance with USNRC, ASME & PDI Guidelines.
On-Site Appendix VIII Hands-On Guided Practice Session INQUAL proctor will provide approximately 15 specimens delivered to your site.Proctor will also administer practice session.Certificate of Completion for each technician completing 8 Hour Practice Session.Proctor fee $75 per hour travel, $125 per hour On-Site and $100 per diem plus fuel.
Includes: Unlimited access to INQUAL's specimen inventory
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
INDUSTRIES THAT USE FLAWTECH SPECIMENS
RENTAL
PRICE LIST
Supplement 2 -
Supplement 3 -
Supplement 10 -
Notes
180° Seg 280 Lbs $75
Cast Stainless *** 320 Lbs $75
130° Seg 205 Lbs $100
120° Seg 322 Lbs $100
120° Seg 322 Lbs $100
Notes Weigth Cost/Day
FlawTech 03-12-09 12" 0.688" flush yes 4 178 Lbs $75
180° Seg
120° Seg
120° Seg $100
Weight Cast/Day
$75
$75
$75
180° Seg 75 Lbs
180° Seg $100
180° Seg $100
120° Seg $100
180° Seg $100
120° Seg $100
120° Seg $100
60° Seg $150
60° Seg $150
AUSTENITIC PIPING SPECIMENSLOCATION SPEC # DIA WALL CROWN GEOMETRY # Flaws Weight Cost/Day
FlawTech 02-02-14 2" 0.218" flush no 2 11 Lbs $50
FlawTech 02-04-01 4" 0.337" flush no 4 30 Lbs $50
FlawTech 02-04-02 4" 0.337" flush no 4 30 Lbs $50
FlawTech 02-06-01 6" 0.718" as-welded yes 4 91 Lbs $50
FlawTech 02-06-02 6" 0.718" as-welded yes 4 91 Lbs $50
FlawTech 02-08-01 8" 0.500" flush yes 4 87 Lbs $75
FlawTech 02-08-02 8" 0.500" flush no 4 87 Lbs $75
FlawTech 02-10-01 10" 0.594" as-welded yes 4 129 Lbs $75
FlawTech 02-10-02 10" 0.594" as-welded yes 4 129 Lbs $75
FlawTech 02-12-01 12" 1.125" as-welded yes 4 280 Lbs $75
FlawTech 02-12-02 12” 1.125" as-welded yes 4 280 Lbs $75
FlawTech 02-12-31 12" 1.125" as-welded yes 3
FlawTech 02-12-42 12" 1.312” flush no 4 ***
FlawTech 02-14-08 14" 0.750" blended yes 5 212 Lbs $100
FlawTech 02-14-09 14" 0.750" blended yes 5 212 Lbs $100
FlawTech 02-16-01 16" 1.219" flush yes 4 385 Lbs $100
FlawTech 02-16-02 16" 1.219" flush no 4 385 Lbs $100
FlawTech 02-18-07 18" 1.781” flush yes 3
FlawTech 02-24-01 24" 2.00" flush no 3
FlawTech 02-24-02 24" 2.00" flush no 3
LOCATION SPEC # DIA WALL CROWN GEOMETRY # Flaws
FlawTech 03-04-01 4" 0.337" flush no 4 30 Lbs $50
FlawTech 03-04-02 4" 0.337" flush no 4 30 Lbs $50
FlawTech 03-04-08 4" 0.337" flat-topped no 2 30 Lbs $50
FlawTech 03-06-03 6" 0.718" flush yes 4 91 Lbs $50
FlawTech 03-08-01 8" 0.500" as-welded yes 4 87 Lbs $75
FlawTech 03-12-01 12" 1.125" as-welded yes 4 280 Lbs $75
FlawTech 03-12-11 12" 0.688" flush yes 4 178 Lbs $75
FlawTech 03-16-01 16" 1.593" flush yes 4 245 Lbs $100
FlawTech 03-18-02 18" 1.562" as-welded yes 2 182 Lbs $100
FlawTech 03-36-01 32" 3.125” flat-topped yex 4 198 Lbs
LOCATION SPEC # DIA.-WALL-GEOMETRY
FlawTech 10-04-01 4" Dia. 0.674" wall CS to SS with Inco butter and SS weld 56Lbs
FlawTech 10-04-03 4" Dia. 0.531" wall CS to SS with Inco butter and weld 46 Lbs
FlawTech 10-04-04 4" Dia. 0.337" wall CS to SS with Inco butter and weld 30 Lbs
FlawTech 10-07-02 7" Dia. 1.137" wall CS to Inco with Inco weld $100
FlawTech 10-08-03 8" Dia. 0.500” wall CS with Inco clad to SS with inco butter & weld 85 Lbs $100
FlawTech 10-12-02 12" Dia. 1.125 wall CS with SS clad to Inco with Inco butter & weld 140 Lbs
FlawTech 10-14-02 14" Dia. 1.094" wall CS with SS clad to SS pipe with Inco butter & weld 150 Lbs
FlawTech 10-20-03 20" Dia. 1.125" wall CS pipe to Inconel pipe with Inconel weld 128 Lbs
FlawTech 10-20-04 20" Dia. 1.125" wall CS pipe to Inconel pipe with Inconel weld 128 Lbs
FlawTech 10-24-02 24" Dia. 1.531" wall CS pipe with SS clad to SS pipe with Inco weld Inco butter 245 Lbs
FlawTech 10-24-03 24" Dia. 1.531" wall CS pipe with SS clad to SS pipe with Inco weld Inco butter 245 Lbs
FlawTech 10-40-02 40" Dia. 3.6" wall CS pipe to Inconel safe end, Inconel weld to Inconel pipe 400 Lbs
FlawTech 10-40-03 40" Dia. 3.6" wall CS pipe to Inconel safe end, Inconel weld to Inconel pipe 400 Lbs
FERRITIC PIPING SPECIMENS
DISSIMILAR METAL SPECIMENS
ASME BPVC, SECTION XI, APPENDIX VIII
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
INDUSTRIES THAT USE FLAWTECH SPECIMENS
RENTAL
PRICE LIST
Radiographic Testing Kit (RT Kit) - Part # RK-1
2 Each - Plates ( 0.625"T x 4"W x 8"L)
6 Each - Plates (0.375"T x 4"W x 8"L)
1 Each - Pipe (4" Dia. x 0.337" wall x 8" Long)
1 Each - Tee (0.375"T x 4"W x 4"H x 8"L)
70 Lbs
$40/day
Ultrasonic Testing Kit (UT Kit) - Part # UK-1
4 Each - Plates ( 0.625"T x 4"W x 8"L)
4 Each - Plates (0.375"T x 4"W x 8"L)
1 Each - Pipe (4" Dia. x 0.337" wall x 8" Long)
1 Each - Tee (0.375"T x 4"W x 4"H x 8"L)
70 Lbs
$40/day
Magnetic Particle / Liquid Penetrant Testing Kit (MT/PT Kit)- Part # MK-1
8 Each - Plates ( 0.250"T x 4"W x 8"L)
2 Each - Tee (0.250"T x 4"W x 4"H x 8"L)
35 Lbs
$40/day
Visual Testing Kit (VT Kit) - Part # VK-1
7 Each - Plates ( 0.250"T x 4"W x 8"L)
3 Each - Tee (0.250"T x 4"W x 4"H x 8"L)
35 Lbs
$40/day
NDT Demonstration Kit (Demo Kit) - Part # DK-1
(Contains 11 Flaws in 5 Specimens)
2 Each - Plates ( 0.625"T x 4"W x 8"L)
1 Each - Plates (0.375"T x 4"W x 8"L)
1 Each - Pipe (4" Dia. x 0.337" wall x 8" Long)
1 Each - Tee (0.375"T x 4"W x 4"H x 8"L)
35 Lbs
$30/day
STANDARD FLAWED SPECIMEN KITS
4486 RACEWAY DR.
CONCORD, NORTH CAROLINA USA 28027
TEL: 704-795-4401 FAX: 704-795-4403 WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology
INDUSTRIES THAT USE FLAWTECH SPECIMENS
RENTAL
PRICE LIST
ADVANCED FLAWED SPECIMEN KITS FOR RENT
API-UT-1 Qualification Kit - Part # API-K1
4 Specimen Set
- 3 Real Flaws in each Specimen
- Advanced Flaw Tolerance
- Flaws include: LOF, Cracks, LOP, Porosity, etc.
Plate with Double Vee (1.0"T x 12"W x 15"L) 50 Lbs
Plate with Single Vee (0.5"T x 10"W x 12"L) 17 Lbs
Pipe with Single Vee (8" Sch 80 x 12"L) 44 Lbs
Pipe with Single Vee (12" Sch 80 x 12"L) 89 Lbs
Optional: 10% Notches, Sec.V Cal Blocks, X-rays, Storage Box
Total 200 Lbs
$75/Day
AWS / CWI Training Kit - Part # AWS-K1
10 Specimen Set
- Designed in accordance with AWS D1.1
- 2 Flaws in each specimen
- Free Carrying Case
- Document Package with CAD Drawings
- Flaws are designed to be "borderline" acceptable
4 Each - Welded Tee (0.25"T x 2"H x 4"W x 6"L) 2 Lbs Ea.
4 Each - Welded Plates (0.25"T x 4"W x 6"L) 2 Lbs Ea.
2 Each - Welded Edge Lap Joint (0.312"T x 4"W x 6"L) 2 Lbs Ea.
Total 25 Lbs
$40/Day
ASME Appendix VII Kit - Part # A7-K1
8 Specimen Set
- Designed in accordance with ASME Section XI, Appendix VII
- Each specimens contains between 2 and 4 real flaws
- All flaw locations are unique
- Document Package with CAD Drawings
A7-SS-005 Stainless Steel Welded Plate (0.5"T x 10"W x 12"L) 15 Lbs
A7-CS-005 Carbon Steel Welded Plate (0.5"T x 10"W x 12"L) 15 Lbs
A7-SS-010 Stainless Steel Welded Plate (1.0"T x 10"W x 12"L) 29 Lbs
A7-CS-010 Carbon Steel Welded Plate (1.0"T x 10"W x 12"L) 29 Lbs
A7-SS-020 Stainless Steel Welded Pipe (2" Sch 160 x 12"L) 8 Lbs
A7-CS-040 Carbon Steel Welded Pipe (4" Sch 160 x 12"L) 23 Lbs
A7-SS-060 Stainless Steel Welded Pipe (6" Sch 160 x 12"L) 44 Lbs
A7-CS-100 Carbon Steel Welded Pipe (10" Sch 160 x
12"Lx180°Seg)116Lbs
Total 300 Lbs
$150/Day
15% DISCOUNT
5 OR MORE DAYS
25% DISCOUNT
10 OR MORE DAYS
REV.10-05
FLAWTECH PRICE LIST PAGE # PART # ITEM WEIGHT
Approx. LBS PRICE US Dollars
4 RK-1 Standard Radiographic Kit 65 $1,975.00 4 RR-1 Reference Radiograph Set 2 $575.00 5 UK-1 Standard Ultrasonic Kit 65 $1,975.00 6 MK-1 Standard Magnetic Particle/Liquid Penetrant Kit 32 $1,350.00 7 VK-1 Standard Visual Kit 32 $1,350.00 8 DK-1 NDT Demonstration Kit 32 $1,100.00
10 P101 UT Practical Exam – 0.75” Plate / Sheet 17 $400.00 10 P102 UT Practical Exam – 1.5” OD Bar 6 $400.00 10 P103 UT Practical Exam – 4” OD Bar 21 $400.00 10 P104 UT Practical Exam – 2” OD L/R 90° Elbow to Pipe 7 $400.00 10 P105 UT Practical Exam – 2” OD Node to 0.375” Plate 10 $400.00 10 P106 UT Practical Exam – 2” OD Pipe to Socket 6 $400.00 10 P107 UT Practical Exam – 0.5” Welded Plate 14 $400.00 10 P108 UT Practical Exam – 1.0” Welded Plate 23 $400.00 10 P109 UT Practical Exam – 4” Welded Pipe 7 $400.00 10 P110 UT Practical Exam – Lap Joint 14 $400.00 10 P111 UT Practical Exam – Forged Pipe Flange 5 $400.00 10 P112 UT Practical Exam – 0.5” Welded Tee 7 $400.00 11 P001 MT/PT Practical Exam – Cast Fitting 3 $300.00 11 P002 MT/PT Practical Exam – Machined Spindle 4 $300.00 11 P003 MT/PT Practical Exam – Bolt & Nut 3 $300.00 11 P004 MT/PT Practical Exam – Forged Hook 2 $300.00 11 P005 MT/PT Practical Exam – Forged Shackle & Pin 3 $300.00 11 P006 MT/PT Practical Exam – Formed Plate 2 $300.00 11 P007 MT/PT Practical Exam – Welded Plate 13 $300.00 11 P008 MT/PT Practical Exam – Welded Pipe 7 $300.00 11 P009 MT/PT Practical Exam – Forged Pipe Flange 5 $300.00 11 P010 MT/PT Practical Exam – Machined Gear 3 $300.00 11 P011 MT/PT Practical Exam – Welded Tee 7 $300.00 11 P012 MT/PT Practical Exam – Pipe to Socket Weld 6 $300.00 13 UA-001 Adv. Specimen – 0.5” Plate w/ SV 21 $500.00 13 UA-002 Adv. Specimen – 0.75” Plate w/ SV 31 $590.00 13 UA-003 Adv. Specimen – 1.0” Plate w/ SV 54 $650.00 13 UA-004 Adv. Specimen – 1.25” Plate w/ DV 74 $800.00 13 UA-005 Adv. Specimen – 6” Sch 120 Pipe Weld 36 $600.00 13 UA-006 Adv. Specimen – 6” Sch XXH Pipe Weld 53 $650.00 13 UA-007 Adv. Specimen – 8” Sch 80 Pipe Weld 43 $700.00 13 UA-008 Adv. Specimen – 12” Sch 80s Pipe Weld 66 $850.00 13 UA-009 Adv. Specimen – 12” Sch 120 Pipe Weld 126 $900.00 13 UA-010 Adv. Specimen – 1.0” Tee Weld w/ SV 41 $700.00 13 UA-011 Adv. Specimen – 1.0” Tee Weld w/ DV 41 $800.00 13 UA-012 Adv. Specimen – 1.25” Tee Weld w/ DV 80 $850.00 13 UA-013 Adv. Specimen – 1.25” Y Joint 80 $850.00 13 UA-014 Adv. Specimen – 10” Sch 120 Node to Carrier 205 $1,800.00 13 UA-015 Adv. Specimen – 8” Sch 80 Nozzle to Carrier 160 $1,500.00 13 RA-001 Adv. Specimen – 0.375” Plate w/ SV 16 $500.00 13 RA-002 Adv. Specimen – 0.625” Plate w/ DV 26 $575.00 13 RA-003 Adv. Specimen – 0.75” Plate w/ SV 31 $600.00 13 RA-004 Adv. Specimen – 1.0” Plate w/ SV 54 $675.00 13 RA-005 Adv. Specimen – 1.0” Plate w/ DV 54 $700.00
FLAWTECH PRICE LIST
PAGE # PART # ITEM WEIGHT Approx. LBS
PRICE US Dollars
13 RA-006 Adv. Specimen – 2” Sch 80 Pipe Weld 5 $500.00 13 RA-007 Adv. Specimen – 6” Sch 120 Pipe Weld 36 $625.00 13 RA-008 Adv. Specimen – 12” Sch 80 Pipe Weld 66 $850.00 13 MA-001 Adv. Specimen – 0.375” Plate w/ SV 16 $350.00 13 MA-002 Adv. Specimen – 6” Sch 80 Pipe Weld 29 $550.00 13 MA-003 Adv. Specimen – 12” Sch 40 Pipe Weld 50 $700.00 13 MA-004 Adv. Specimen – 0.375” Tee w/ SV 16 $400.00 13 MA-005 Adv. Specimen – 0.375” Y Joint 16 $400.00 13 MA-006 Adv. Specimen – 10” Sch 40 Node to Carrier 77 $725.00 13 MA-007 Adv. Specimen – 8” Sch 60 Nozzle to Carrier 72 $700.00 14 API-K1 API-UT-1 Kit 200 $3,395.00 15 AWS-K1 AWS / CWI Kit 50 $1,750.00 16 A7-K1 ASME Sec. XI, Appendix VII Kit 275 $15,500.00 17 S2-K1 ASME Sec. XI, Appendix VIII Kit, Sup. 2 350 Quote Only 17 S3-K1 ASME Sec. XI, Appendix VIII Kit, Sup. 3 360 $19,875.00 17 S10-K1 ASME Sec. XI, Appendix VIII Kit, Sup. 10 340 Quote Only 19 4S-CB-1 4 Step Calibration Block 1 $170.00 19 5S-CB-1 5 Step Calibration Block 1 $185.00 19 DSC-CB-1 DSC Calibration Block 2 $295.00 19 RC-CB-1 AWS Resolution Calibration Block 5 $245.00 19 DS-CB-1 DS Calibration Block 11 $595.00 20 PDI-CB-1 PDI Alternative ASME Cal. Block – 516-70 c/s 8 $2,350.00 20 PDI-CB-2 PDI Alternative ASME Cal. Block – 304 s/s 8 $2,600.00 20 PDI-CB-3 PDI Alternative ASME Cal. Block – 316 s/s 8 $2,600.00 20 PDI-CB-4 PDI Alternative ASME Cal. Block – Set of 3 35 $5,800.00 21 EPRI CS-4774 Basic Cal. Blocks N/A Quote Only 21 ASME Sec. XI Basic Piping Cal Blocks N/A Quote Only 22 2” Circ. Block for Angles ≤ 50° s/s 1 $1,365.00 22 4” Circ. Block for Angles ≤ 50° s/s 2 $2,160.00 22 2” Contour Block for Axial Scans s/s 2 $3,855.00 22 4” Contour Block for Axial Scans s/s 7 $4,825.00 22 12 – 24 Contour Probe Block s/s 31 $6,550.00 22 12” Stainless Pipe Segment Block s/s 11 $5,710.00 22 24” Stainless Pipe Segment Block s/s 24 $6,335.00 22 PDI-UT-10 Cal. Block Set of 7 78 $27,720.00 23 Overlay Step Wedge 15 Quote Only
PRICE LIST EFFECTIVE DATE 1/06 Notes:
Material for each item listed in the price list is carbon steel (c/s) unless otherwise noted. For example stainless steel items will have s/s at the end.
FlawTech will quote any material type for above items. Pricing is based on current material cost and availability, FlawTech reserves the
right to change any price of any item without notice.
4486 RACEWAY DR.
CONCORD, NC 28027
TEL: (704) 795-4401
FAX: (704) 795-4403
WWW.FLAWTECH.COM
Flaw Manufacturing TechnologyFlaw Manufacturing Technology