Detec�on range
Antenna module
27.525.014
Dual-Photocell Sensor
Hold �meDaylight sensor
Stand-by period Stand-by dimming level
Push Power supplyDALI
DA DA Push 1 Push 2
M3x8
M3x8
87
4.0 45.0
94102
t | +44(0)1543 396400 | e | [email protected] | w | www.fox-lux.co.uk
DALI DIMMING MICROWAVE MOTION SENSOR
MODEL: FXS03DL
DALI Dimming
This sensor contains a DALI power supply circuit, which gives DALI output to the driver to carry out the sensor on/off and dimming control.
FXS03DL - KEY FEATURES
• DALI dimming control
• Easy programming via DIP switches
• Dual-photocell technology allows real daylight monitoring for use with 'step-dim' drivers in built-in applications
• Zero-cross circuit protects the sensor relay against in-rush current, thereby maximising product life expectancy
• 5.8GHz C-band microwave motion sensor
• Operating voltage: 120 - 277V AC 50 - 60Hz
• Switched power : max. 30 devices; max. 60mA
• Stand-by power:
OFF
30sT3s*
3
OFF
ON1
100%
2
75%
50%
25%
Hold-time
This setting adjusts the period of full brightness after motion detection.
2
1
3
Detection rangeDetection range can be reduced by selecting the combination on the DIP switches to fit user requirements.
Daylight sensor
This setting adjusts the daylight threshold to enable or disable the sensor function.
“Disable”:
“50lux”:
The sensor works always, even during daylight.
The sensor works only in twilight.
“10lux, 2lux”: The sensor works only in the dark.
* to enter test mode (walk test) set hold-time to T3s*. This mode enables the user to set the desired detection range. In this mode, the daylight sensor is disabled, so when there is no motion detected the luminaire remains on. When motion is detected, the luminaires cycles 3s on and 2s off.
4 5
90s5min10min30min
ON
OFF
ON6 7
Disable
10lux
50lux
2lux
I
II
III
IV
I
II
III
IV
I
IIIIIIVVVI
On→Off: luminaire turns off immediately and cannot be triggered ON again by motion until the expiration of pre-set hold-time. After this period, the sensor goes back to normal sensor mode.
Off→On: the light turns on and goes to sensor mode.In some applications the user may not want to have a sensor automatically switch on the light, the sensor will be activated only on the manual Off→On press.
Long push (>1s) : adjust the dimming levelShort push (
8
+ = bi-level dimming control - luminaire always on.8
4 Stand-by period
This is the time period that the luminaire remains at a low light level before it is completely switched off in the long absence of detected motion.
OFF
ON9 10
10s
5min
30min
1h
10min
+ 8
5 Stand-by dimming level
This is the desired dimmed low light level after the hold-time in the absence of detected motion.
OFF
ON11
0%
12
10%
30%
50%
*I
II
III
IV
I
IIIIIIVVVI
*0% = on/off control
10% Vdim = 1.5Vdc
30% Vdim = 3.0Vdc
50% Vdim = 5.0Vdc
DALI Driver
Push1Push2
FXS03DL
L N
DA DA L NLED
+ -
DALI Driver
DA
DA- DA+
DA L NLED
+ -
t | +44(0)1543 396400 | e | [email protected] | w | www.fox-lux.co.uk
WIRING DIAGRAM
Ceiling mount (m) Wall mount (m)
Hei
ght
(m)
Hei
ght
(m)
DAYLIGHT MONITORING
Utilising dual-photocell technology, the sensor can differentiate between natural light and artificial light from behind the diffuser. It can switch on automatically (even without movement) when the ambient light is below the target value, and then switch off automatically whenever the artificial light is not required (sufficient ambient light).
This is REAL & INTELLIGENT daylight monitoring for built-in applications.
Note: Lux-Off sampling time: ~30s; Lux-On sampling time: ~10s.
Lux-On function takes effect only when standby dimming period set at + ∞ .
Brighter
Darker
Lux On Level
Lux Off Level
Ambient Light LevelLux Time Lux Time
Occupancy detected
Lights turn on Lights turn off
lssue V1: 5/1/2020
t | +44(0)1543 396400 | e | [email protected] | w | www.fox-lux.co.ukRegistered Office: Alex House 260/8 Chapel Street, Salford, Manchester, M3 5JZ
Company Registration No. 11821284 VAT Registration No. 320 9921 12
DETECTION PATTERN
Top Related