Vibration Sensors Catalog[1]

SKFVibration Sensors

Vibration sensors•

Sensor selection, installation •and mounting overview

Cables and connectors•

Sensor housings•

Mounting accessories•

Power supply units•

CMSS 2100Standard Industrial Acceleration Sensor …

Typical Temperature Response

Temperature, °C (°F)

Dev

iatio

n, %

Sen

sitiv

ity

-20 0 +25 +50 +80 +120 (-4) (+32) (+77) (+122) (+176) (+248)

+20

+10

0

-10

-20

… Incorporating the latest in technology to meet demanding CE, EMC, and low noise level requirements.

Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF offers rugged accelerometers designed for the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.

FeaturesFor use with the SKF Local Monitoring Unit (LMU’s) on-line •systems, protection systems and the ever versatile portable data collection Instruments.

Rugged, economical, and all around general purpose sensor.•

Sensitivity, 100 mV/g to optimize use in multiple applications.•

Exceptional bias voltage (BV) stability at elevated temperatures.•

Designed for exceptional low noise level for low frequencies at •elevated temperatures.

Meets stringent CE, EMC requirements.•

Smaller profile industrial accelerometers.•

Two (2) mounting studs (1/4–28 and M8 x 1.25) provided.•

Corrosion resistant and hermetically sealed for installation in high •humidity areas.

Reverse polarity wiring protection.•

Typical Frequency Response

0.5 10 100 1 k 20 kFrequency, Hz

Dev

iatio

n, d

B

10

3

2

1

0

-1

-2

-3

For additional information on SKF Reliability Systems products, contact:

SKF Reliability Systems5271 Viewridge Court • San Diego, California 92123 USATelephone: +1 858-496-3400 • FAX: +1 858-496-3531

Web Site: www.skf.com/cm® SKF is a registered trademark of the SKF Group.• All other trademarks are the property of their respective owners.•

© SKF Group 2008The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF reserves the right to alter any part of this publication without prior notice.

SKF Patents include: #US04768380 • #US05679900 • #US05845230 • #US05854553 • #US05992237 •#US06006164 • #US06199422 • #US06202491 • #US06275781 • #US06489884 • #US06513386 • #US06633822 • #US6,789,025 • #US6,792,360 • US 5,633,811 • US 5,870,699 • #WO_03_048714A1

Publication CM2205 EN (Revised 4-08) • Printed in the United States of America

CMSS 2100Standard Industrial Acceleration Sensor

SpecificationsSpecifications conform to ISA-RP-37.2 (1-64) and are typical values referenced at +24 °C (+75 °F), 24 Vdc supply, 4 mA constant current and 100 Hz.

DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 5% at +25 °C (+77 °F)Acceleration range: 80 g PeakAmplitude linearity: ≤ 1%, up to full scaleFrequency range:± 5%; 3.0 Hz to 5,000 Hz± 10%; 1.0 Hz to 9,000 Hz± 3 dB; 0.5 Hz to 14,000 HzResonance frequency: Mounted, nominal 30 kHzTransverse sensitivity: ≤ 5% of axial

ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, +18 Vdc to +30 VdcConstant current diode: 2 to 10 mA dc, recommended 4 mAElectrical noise: 2.0 Hz; 20µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 VdcGrounding: Case isolated, internal shielding

ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F), operating temperatureVibration limits: 500 g peakShock limit: 5,000 g peakElectromagnetic sensitivity, equivalent g: 70 µg/GaussSealing: HermeticBase strain sensitivity: 200 µg/microstrainCE: According to the generic immunity standard for

Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent

g level” under the above test conditions should be less than 2 milli g peak to peak.

PHYSICALDimensions: See drawingWeight: 90 gms (≈ 3.17 oz.)Case material: 316L stainless steel

Mounting: Internal 1/4–28 thread. Mounting studs provided. One (1) 1/4–28 to 1/4–28 english thread and one (1) M8 x 1.25 metric thread.Mounting torque: 2,9 N-m (24 in-lbs)Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS 3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 100 pF/m (30 pF/ft)

Diagrams

Ordering informationCMSS 2100 General purpose industrial standard acceleration sensor with top exit C5015 two (2) pin connector.

1/4-28 and M8 mounting studs provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.

53.0 mm(2.10”) MODEL CMSS2100

S/N S00000

2-Pin connector

100 mV/g NOM

Made in the USA

A B

20.3 mm(0.80”)

22.3 mm(0.87”)

19.0 mm(0.75”)

Diameter1/4-28

Mounting hole

7/8”HEX

… Incorporating the latest in technology to meet the demanding CE, EMC and low level noise requirements.

Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Condition Monitoring offers rugged accelerometers designed for the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.

FeaturesFor use with the SKF Local Monitoring •Unit (LMU’s) on-line systems, protection systems and the ever versatile portable data collection Instruments.

Rugged, economical, and all around general •purpose sensor.

Sensitivity, 100 mV/g to optimize use in •multiple applications.

Exceptional bias voltage (BV) stability at •elevated temperatures.

Designed for exceptional low noise level for low frequencies at elevated temperatures.•


Low profile for side industrial accelerometer with captive mounting bolts (1/4–28, M6 x 1.00 or •M8 x 1.25) provided.

Corrosion resistant and hermetically sealed.•


CMSS 2200/CMSS 2200-M8Low Profile Standard Acceleration Sensor …


Dev

iatio

n, %

Sen

sitiv

ity


-20 0 +25 +50 +80 +120 (-4) (+32) (+77) (+122) (+176) (+248)

+20

+10

0

-10

-20



Dev

iatio

n, d

B

3

2

1

0

-1

-2

-3







CMSS 2200/CMSS 2200-M8Low Profile Standard Acceleration Sensor


DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Acceleration range: 80 g peakAmplitude linearity: 1%Frequency range:± 10%; 1.0 Hz to 5,000 Hz± 3 dB; 0.7 Hz to 10,000 HzResonance frequency: Mounted, minimum 22 kHzTransverse densitivity: ≤ 5% of axial

ELECTRICALPower requirements:Voltage source: +18 Vdc to +30 VdcConstant current diode: 2 to 10 mA dc, recommended 4 mAElectrical noise: 2.0 Hz; 20 µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 VdcGrounding: Case isolated, internal shielding

ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F) operating temperatureVibration limits: 500 g peakShock limit: 5,000 g peakElectromagnetic sensitivity, equivalent g: 70 µg/GaussSealing: HermeticBase strain sensitivity: 200 µg/microstrainCE: According to the Generic immunity standard for

Industrial Environment EN50082-2. Acceptance criteria: The generated “false equivalent g

level” under the above test conditions should be less than 2 milli g peak to peak.

PHYSICALDimensions: See drawingWeight: 145 gms (≈ 5.10 oz.)Case material: 316L stainless steelMounting: Captive mounting bolts provided. One (1) 1/4–28 english thread and one (1) M6 x 1.00 metric thread.Mounting torque: 30 in-lbs, 3,4 N-m

Ordering informationCMSS 2200 • Low Profile Acceleration Sensor with side exit C5015 two (2) pin connector.


CMSS 2200-M8 • Low Profile Acceleration Sensor with side exit C5015 two (2) pin connector.

M8 mounting stud provided. Calibration sensitivity is provided on each accelerometer package with nominal sensitivity etched on each unit.

Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS 3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 100 pF/m (30 pF/ft)

Diagrams

A B

+ -

MODEL CMSS2200S/N S0000

25.0 mm(1.00”)

38.0 mm(1.50”) 26.0 mm

(1.04”)

2-PinConnectorMIL-C-5015

37.0 mm(1.44”)

53.0 mm(2.10”)

5/32” Allen Head

CMSS 2200:1/4-28 MountingthreadCMSS 2200-M8:M8 Mounting thread

… Incorporating the latest in technology to meet the demanding and stringent elevated temperature requirements such as those associated with tropic and desert installations, steel mills, and pulp and paper applications.

Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Reliability Systems offers rugged high temperature accelerometers designed for machines of the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.

FeaturesFor use with the SKF Local Monitoring Unit (LMU’s) On-line Systems, •Protection Systems and the ever versatile Portable Data Collection Instruments.

Rugged, economical, and all around high temperature general purpose •sensor for up to +150 °C (+302° F) operating temperature.

Sensitivity, 100 mV/g to optimize use in multiple applications.•

Exceptional bias voltage (BV) stability at elevated temperatures.•

Designed for exceptional low noise level for low frequencies at elevated •temperatures.


Two (2) mounting studs (1/4–28 and M8 x 1.25) provided.•

Corrosion resistant and hermetically sealed for installation in high •humidity areas.


CMSS 2106High Temperature Industrial Acceleration Sensor …


Dev

iatio

n, %

Sen

sitiv

ity +20

+10

0

-10

-20


-50 -25 0 +25 +50 +75 +100 +125 +150 (-58) (+13) (+32) (+77) (+122) (+167) (+212) (+258) (+302)


1 10 100 1 k 10 k 13 kFrequency, Hz

Dev

iatio

n, d

B

3

2

1

0

-1

-2

-3







CMSS 2106High Temperature Industrial Acceleration Sensor


DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at -50 °C to +150 °C (-58 °F to +302 °F)Acceleration range: 50 g peakAmplitude linearity: 1%Frequency range:± 5%; 4.0 Hz to 4,000 Hz± 10%; 3.0 Hz to 6,000 Hz± 3 dB; 1.0 Hz to 10,000 HzResonance frequency: Mounted, nominal 20 kHzTransverse sensitivity: ≤ 5% of axial

ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, +18 Vdc to +30 VdcConstant current diode: 2 to 4 mA dc, recommended 4 mAElectrical noise: 2.0 Hz; 30µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 Vdc at +25 °C (+77 °F); 11 Vdc at +150 °C (+302 °F)Grounding: Case isolated, internal shielding

ENVIRONMENTALTemperature range: -50 °C to +150 °C (-58 °F to +302 °F) operating temperatureVibration limits: 500 g peakShock limit: 2,500 g peakElectromagnetic sensitivity, equivalent g: 15 µg/GaussSealing: HermeticBase strain sensitivity: 500 µg/microstrainCE: According to the Generic immunity standard for

Industrial Environment EN50082-2. Acceptance Criteria: The generated “false equivalent


PHYSICALDimensions: See drawingWeight: 135 gms (≈ 4.73 oz.)

Case material: 316L stainless steelMounting: Internal 1/4–28 thread. Mounting studs provided. One (1) 1/4–28 to 1/4–28 english thread and one (1) M8 x 1.25 metric thread.Mounting torque: 2,9 N-m (24 in-lbs)Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS-3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 30 pF/ft (100 pF/m)

Diagrams

A B

61.0 mm(2.42”)

MODELCMSS2106

S/N S00000

2-Pin connector

100 mV/gNOM

23.8 mm(0.94”)

Diameter1/4-28

Mounting hole

15/16”HEX

45.0 mm(1.78”)

25.0 mm(1.00”)

Diameter

Made in theUSA

Ordering informationCMSS 2106 High Temperature Industrial Standard Acceleration Sensor with top exit C5015 two (2) pin connector.


… Incorporating the latest in technology to meet the demanding and stringent elevated temperature requirements such as those associated with tropic and desert installations, steel mills and pulp and paper applications.

Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Condition Monitoring offers rugged high temperature accelerometers designed for the Pulp and Paper, Petrochemical, Steel, Mining and Construction, Metal Working, and Machine Tool Industries.

FeaturesFor use with the SKF Local Monitoring Unit •(LMU’s) On-Line Systems and Protection Systems.

Rugged, economical, and all around high •temperature general purpose sensor for up to +150 °C (+302 °F) operating temperature.

Sensitivity, 100 mV/g to optimize use in •multiple applications.

Exceptional bias voltage (BV) stability at •elevated temperatures.

Designed for exceptional low noise level for low •frequencies at elevated temperatures.


Low profile, side exit, high temperature industrial accelerometer.•

Corrosion resistant and hermetically sealed for installation in high humidity areas.•


CMSS 2207High Temperature Low Profile Acceleration Sensor …


Dev

iatio

n, %

Sen

sitiv

ity


0 +25 +50 +75 +100 +120 (+32) (+77) (+122) (+167) (+212) (+248)

+20

+10

0

-10

-20



Dev

iatio

n, d

B

3

2

1

0

-1

-2

-3







CMSS 2207High Temperature Low Profile Acceleration Sensor


DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Acceleration range: 50 g peakAmplitude linearity: ≤ 1% up to full scaleFrequency range:± 5%; 4.0 Hz to 5,000 Hz± 10%; 3.0 Hz to 7,000 Hz± 3 dB 1.0 Hz to 11,000 HzResonance frequency: 20 kHzTransverse sensitivity: ≤ 5% of axial

ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, +18 Vdc to +30 VdcConstant current diode: 2 to 4 mA dc, recommend 4 mAElectrical noise: 2.0 Hz; 30µg/√HzOutput impedance: < 100 OhmsVoltage bias: 12 Vdc at +25 °C (+77 °F); 11 Vdc at +150 °C (+302 °F)Grounding: Case isolated, internal

ENVIRONMENTALTemperature range: -50 °C to +150 °C (-58 °F to +302 °F) operating temperatureVibration limits: 500 g peakShock limit: 2,500 g peakElectromagnetic sensitivity, equivalent g: < 5 µg/GaussBase strain sensitivity: 100 µg/microstrainCE: According to the Generic immunity standard for



PHYSICALDimensions: See drawingWeight: 145 gms (≈ 5.10 oz.)Case material: 316L stainless steelMounting: Captive mounting bolts provided. One (1) each 1/4–28 english thread and one (1) M6 x 1.00 metric thread.Mounting torque: 3,4 N-m (30 in-lbs)

Ordering informationCMSS 2207 • Low Profile High Temperature Acceleration Sensor with side exit C5015 two (2) pin connector.


Connector:Pin A: Signal/power (White wire)Pin B: Common (Black wire)Mating connector: CMSS 3106F-10SL-4S or equivalentRecommended cable: Two conductor shielded, teflon jacket, 100 pF/m (30 pF/ft)

Diagrams

Side View

A B

End View

Top View

Bottom View

100

mV/

g N

OM

Mad

e in

the

USA

30.0 mm(1.20”)

1/4-28Mounting

Thread

2-PinConnectorMIL-C-5015

Safety Wire Hole1.5 mm (0.062”)Diameter

43.0 mm(1.70”)

6.0 mm(0.25”)

26.0 mm(1.05”)

Diameter

54.0 mm (2.15”)

CMSS 2110-3Industrial acceleration sensor with integral 5 meter (16.5 feet) rugged stainless steel braided cable …

… Incorporating the latest in technology to meet demanding CE, EMC and low noise level requirements.

FeaturesDesigned for use with the SKF Machine •Condition Transmitters (MCT)

Economical, rugged, general purpose•

Sensitivity, 30 mV/g to optimize use in most •applications

Designed to meet stringent CE, EMC •requirements

Cable shield and braid connected to sensor •housing for better noise rejection

Corrosion resistant•

Miswiring protection•

SpecificationsDYNAMICSensitivity: 30 mV/g at +20 °C (+68 °F)Sensitivity precision: ± 10% at +20 °C (+68 °F)Sensitivity deviation over full temperature range: < ± 10% of the sensitivity at +20 °C (+68 °F)Amplitude linearity: < 1% up to full scaleTransverse sensitivity: < 5% of axialFrequency range:3.0 Hz – 8.0 kHz, ± 10% at +20 °C (+68 °F)0.8 Hz – 10.0 kHz, ± 3 dB at +20 °C (+68 °F)Sensor resonance frequency: Nominal 20 kHz or higher. Controlled resonance amplitude. Second order Q limiting filter.Acceleration output range: Minimum ± 6 V equivalent to 200 g peak. Turn on time for one (1) time constant is 0.5 seconds.

ELECTRICALPower Requirements:Voltage Source: +24 Vdc, ± 20%Constant Current Diode: 2 – 6 mA dcElectrical noise: Broadband (2 Hz to 20 kHz) < 0.7 milli g RMSOutput impedance: < 50 Ohms


Dev

iatio

n, %

Sen

sitiv

ity

+10

+5

0

-5

-10


-50 -25 0 +25 +50 +75 +100 +120 (-58) (+13) (+32) (+77) (+122) (+167) (+212) (+248)

Frequency, Hz


Ampl

itude

(dB

)

+20

+10

0

-10

-200.8 100 1k 30k 40k10k 20k

Standard Armored Cable

1/4 – 28"

Bend Radius19.0 mm (0.75”)

CMSS 2110/3S/N 98765

22.0 mm(0.87”)

25.0 mm(1.00”)

45.0 mm(1.75”)

51.0 mm(2.00”)

25.0 mm(1.00”) Hex







CMSS 2110-3Industrial acceleration sensor with integral 5 meter (16.5 feet) rugged stainless steel braided cable

SpecificationsELECTRICAL (continued)

Grounding: Case isolated, internal shielding (Faraday cage). The internal Faraday cage is connected to the signal return of the shielded twisted pair. The internal shield as well as the stainless steel braid is connected to the sensor housing.Isolation to sensor housing: > 10 Mega Ohms over full temperature range.V bias: 11.5 Vdc (± 10%) for 24 Vdc supply voltage over the temperature range from -50 °C to +100 °C (-58 °F to +212 °F).Over voltage protectionReverse polarity (wiring) protection

ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F) operating temperature.Vibration limits: 500 g peakShock limit: 1,000 g peakElectromagnetic sensitivity, equivalent g: < 100 µg/Gauss at 50 to 60 HzBase strain sensitivity: 200 µg/micro strainCE: According to the Generic immunity standard for



PHYSICALDimensions: See drawing. Integral cable with shielded twisted pair, and stainless steel braid. Cable length is 5 meters (16.5 feet) long.Weight: 350 g (12.25 oz.), including 5 meters (16.5 feet) of cableCase material: 316L stainless steelMounting: 1/4–28 to M8 and 1/4–28 to 1/4–28 mounting studs provided.Cable: Integral cable, 5 meters (16.5 feet) long. Shielded twisted pair; 2 times AWG 20. Shield grounded to sensor housing. Cable armored with stainless steel braid. Braid also connected to sensor housing. High temperature cable. Cable diameter less than 5 mm.Cable specifications: 2/C 20 AWG FEP/A/M/FEP 10-1254.Cable capacitance: 80 pF/m (25 pF/ft).Cable connectors: Integral cable;Power/signal: WhiteCommon: BlackShielding: Drain wire

Diagrams

Ordering informationCMSS 2110-3 General purpose industrial acceleration sensor with 5 meter (16.5 feet) stainless steel over-braided twisted pair cable.

CMSS 2110Industrial Acceleration Sensor with integral 5 meter (16.5 feet) over-braided cable …


DYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10%Sensitivity deviation over full temperature range: ≤ ± 10%Amplitude linearity: ≤ 1% up to full scaleTransverse sensitivity: ≤ 5% of axialFrequency range: 0.8 Hz to 10.0 kHz, ± 3 dBSensor resonance frequency: Nominal 25 kHz or higher. Controlled resonance amplitude. +15 dB maximum at resonance.Acceleration output range: Minimum ± 8 V equivalent to 80 g peak. Turn on time to within 10% of final bias is ≤ 1.0 seconds.

Using detailed knowledge acquired from many years of supplying high quality sensors to a broad spectrum of industry users, SKF Reliability Systems introduces this new series of rugged accelerometers designed for installation where cable protection is paramount without the luxury of cable trays or protective conduit.

FeaturesRecommended for use •with the SKF Machine Condition Transmitters (MCT)

Economical, rugged, •general purpose

Sensitivity, 100 mV/g •to optimize use in most applications

Designed to meet stringent CE, EMC •requirements

Cable shield and braid connected to sensor •housing for better noise rejection

Corrosion resistant•

Miswiring protection•

… Incorporating the latest in technology to meet demanding CE, EMC and low noise level requirements.

Machine Condition Transmitters (MCT)



Dev

iatio

n, %

Sen

sitiv

ity

+10

+5

0

-5

-10 -50 -25 0 +25 +50 +75 +100 +120 (-58) (+13) (+32) (+77) (+122) (+167) (+212) (+248)

0.8 100 1k 30k 40kFrequency, Hz


Ampl

itude

(dB

)

+20

+10

0

-10

-2010k 20k







CMSS 2110Industrial acceleration sensor with integral 5 meter (16.5 feet) over-braided cable

Specifications (continued)

ELECTRICALPower requirements:Voltage source: +24 Vdc nominal, ± 20%Constant current diode: 2 to 10 mA dc, recommend 4 mAElectrical noise: Broadband (2.5 Hz to 25.0 kHz) < 0.6 milli g RMSOutput impedance: < 50 OhmsGrounding: Case isolated, internal shielding (Faraday cage). The internal Faraday cage is connected to the signal return of the shielded twisted pair. The internal shield as well as the stainless steel braid is connected to the sensor housing.Isolation to sensor housing: > 10 MOhms over full temperature rangeV bias:12.5 Vdc to 13.5 Vdc for +24 Vdc supply over temperature range -50 °C to +99 °C (-58 °F to +211 °F)11.0 Vdc to 14.0 Vdc for +24 Vdc supply over temperature range +100 °C to +120 °C (+212 °F to +248 °F)Over voltage protectionReverse polarity (wiring) protection

ENVIRONMENTALTemperature range: -50 °C to +120 °C (-58 °F to +248 °F) operating temperatureVibration limits: 500 g peakShock limit: 1,000 g peakElectromagnetic sensitivity, equivalent g: < 100 µg/Gauss at 50 to 60 HzBase strain sensitivity: 200 µg/micro strainCE: According to the Generic immunity standard for



PHYSICALDimensions: See drawing. Integral cable with shielded twisted pair, and stainless steel braid. Cable length is 5 meters (16 feet) long.Weight: 350 gms (≈ 12.25 oz.) including 5 meters (16.5 feet) of cable.

Case material: 316L stainless steelMounting: Internal 1/4–28 thread. Mounting studs provided. One (1) 1/4–28 to 1/4–28 English thread and one (1) M8 x 1.25 Metric thread.Mounting torque: 2.9 N-m (24 in-pounds)Cable: Integral cable 5 meters (16 feet) long. Shielded twisted pair; 2 times AWG 20. Shield grounded to sensor housing. Cable armored with stainless steel braid. Braid also connected to sensor housing. High temperature cable. Cable diameter less than 5 mm (0.19”).Cable specifications: 2/C 20 AWG FEP/A/M/FEP 10-1254. Recommend two (2) wire, twisted, shielded.Connector: Power signal: White wire Common: Black wire Shielding: Drain wire

Diagrams

Ordering InformationCMSS 2110 General Purpose Industrial Standard Acceleration Sensor with integral 5 meter (16.5 feet) stainless steel over-braided twisted pair cable.


Standard Armored Cable

1/4-28"

Bend Radius19.0 mm (0.75”)

CMSS 2110S/N 98765

22.0 mm(0.87”)

25.0 mm(1.00”)

45.0 mm(1.75”)

51.0 mm(2.00”)

25.0 mm(1.00”) Hex

CMSS MT1Low Profile Machine Tool Accelerometer

The CMSS MT1 Machine Tool accelerometer features a low profile, bolt mounted sensor with a double-shielded integral cable. This sensor is optimized for use with on-line monitoring systems in Machine Tool applications.

FeaturesFor use with the SKF On-line surveillance •systems.

Meets CE, EMC requirements.•

High resistance to electrical •noise.

Low profile side exit industrial •accelerometer with captive bolt (M8 x 1.25, 33 mm length) provided.

Compact design ideal for •mounting with limited space.

Corrosion resistant and •hermetically sealed.

+8+6+4

dB +20

-2-4

0.1 1 10 100 1 k 10 k 12 k Hz







Publication CM2296 EN (4-08) • Printed in the United States of America

SpecificationsDYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Acceleration range: 50 g peakAmplitude linearity: 1% of full scaleFrequency range: ± 3 dB; 0.32 Hz to 10,000 HzResonance frequency: 10 kHz (mounted)Transverse sensitivity: ≤ 5% of axial

ELECTRICALPower requirements:Voltage source: +18 Vdc to +28 VdcConstant current diode: 2 to 10 mA DC, recommended 4 mAElectrical noise: < 100 µV from 2.5 Hz to 25 kHzOutput impedance: < 100 OhmsOutput bias voltage: 8 Vdc to 12 VdcGrounding: Case connected to outer shield, inner shield open

ENVIRONMENTALTemperature range:Operating: -40 °C to +85 °C (-40 °F to +185 °F)Storage: -54 °C to +121 °C (-65 °F to +250 °F)Shock limit: 7,000 g peakSealing: EncapsulatedCE: According to the immunity standard for Industrial Environment EN50082-2, Heavy Industrial

PHYSICALDimensions: See drawingWeight: Shipping weight. See table under Ordering Information.Case material: 304 stainless steelMounting: Captive mounting bolts provided: one (1) M8 x 1.25 Metric thread, 33 mm length.Mounting torque: 4,5 N-m (40 in-lbs)Cable termination:Signal/power: White wireCommon: Black wireInner Shield: Drain wireOuter Shield: Braid

Ordering informationCMSS MT1 General purpose low profile Machine Tool industry accelerometers

Part Number Cable Length Weight

CMSS MT1-16 4.88 meters(16 feet)

256 grams(9 ounces)


482 grams(17 ounces)


964 grams(34 ounces)

CMSS MT1Low Profile Machine Tool Accelerometer

35.95 mm(1.415”)

21.45 mm(0.844”)

8.50 mm(0.335”)17.00 mm

(0.669”)

Ø 8.50 mm(0.335”)

Dimension “A”(Total length)

Double shielded, twisted pair

Outside diameter of cable, approximately 3.6 mm

27.00 mm(1.063”) 19.00 mm

(0.748”)

0.75 mm(0.029”)

12.25 mm(0.482”)

M8 x 1.25 Socket cap head screw (33 mm long)

Drain (open)White (sensor – signal and power)Black (sensor – return)Screen (external shield connected to case)CMSS MT1

S/N 99999

Diagrams

CMSS MT3Special Purpose, Adhesive Mount Accelerometer

ApplicationsMachine Tool Spindles (Adhesive mounting in pre-machined hole)•

General FunctionalityThe CMSS MT3 Machine Tool accelerometer consists of an acceleration sensor with double-shielded integral cable designed for epoxy mounting. This sensor is a custom product designed for machine tool spindle applications (not for general use).

+8+6+4

dB +20

-2-4

0.1 1 10 100 1 k 10 k 12 k Hz







Publication CM2297 EN (4-08) • Printed in the United States of America

CMSS MT3Special Purpose, Adhesive Mount Accelerometer

SpecificationsDYNAMICSensitivity: 100 mV/gSensitivity precision: ± 10% at +25 °C (+77 °F)Amplitude linearity: 1% of full scaleFrequency range: ± 3 dB; 0.32 Hz to 10,000 HzResonance frequency: ≥ 10 kHz (mounted)Transverse sensitivity: < 9% of axial

ELECTRICALPower requirements:Voltage source: +18 Vdc to +28 VdcConstant current diode: 2 to 10 mA DC, recommended 4 mAElectrical noise: < 100 µV from 2.5 Hz to 25 kHzOutput impedance: < 100 OhmsOutput bias voltage: 8 Vdc to 12 VdcGrounding: Case connected to outer shield, inner shield open

ENVIRONMENTALTemperature range:Operating: -40 °C to +85 °C (-40 °F to +185 °F)Storage: -50 °C to +120 °C (-58 °F to +248 °F)

Acceleration range: 50 g peakShock limit: 7,000 g peakSealing: EncapsulatedCE: According to the immunity standard for Industrial Environment EN50082-2, Heavy Industrial

PHYSICALDimensions: The sensor case dimensions are 18.29 mm (round) x 22.00 mm (height). Refer to drawing for details.Weight: 185 gramsCore material: 316L stainless steelMounting: Glued on to machine in pre-machined hole

Ordering informationCMSS MT3-08 Special purpose, adhesive mount, Machine Tool industry accelerometer with 2.5 meter (8 feet) integral cable.

2500 mm (98.43") total length

Outside diameter of cableapproximately 3.6 mm (0.142")

Double-shielded, twisted pair

16.00 mm(0.630")

18.29 mm (ø 0.720")

18.50 mm(0.728")

Drain (Open)Sensor (–) Black WireSensor (+) White Wire

Screen(Connected to Casing)

22.00 mm(0.866")

Diagrams

Vibration Sensors Catalog[1]

Documents

Transcript of Vibration Sensors Catalog[1]