VENTILATION FAN CATALOGUE€¦ · 150mm (Axial) vs 150mm (Centrifugal) fan. The starting point is...

VENTILATION FAN CATALOGUE

Proven, Reliable Bathroom Ventilation Solutions

TABLE OF CONTENTSFANS

Extraction Selection 4

Manrose Pro-Series Wall/Ceiling Mounted Fans 10

Manrose Classic Wall/Ceiling Mounted Fans 12

Manrose Classic Thru Wall Fan Kits 14

Simx WhisperVent Centrifugal Ceiling Fans 16

Manrose Classic Multi-Vent Fans 18

Manrose Classic Wall Fans 18

Manrose Pro-Series Thru Wall Mounted Fan Kits 20

Manrose Classic Thru Wall Mounted Fan Kits 22

Manrose Classic Window Mounted Fans 24

Manrose Classic Window Commercial Fans 26

Manrose Designer Series LED Heat/Fan/Light Kits 28

Manrose Designer Series Heater Fan Lights 30

Manrose Pro-Series Heat/Fan/Light Kits 32

Manrose Classic Heat/Fan/Light Kits 32

Manrose Classic Heat/Light Kits 32

MixFlo Pro-Series Inline Fan Kits 34

Manrose Pro-Series Inline Mounted Fan Kits 36

Manrose Classic Inline Mounted Fan Kits 38

Manrose Pro Series Inline Fan/Light Kits 40

Manrose Classic Inline Fan/Light Kits 42

MixFlo Pro-Series Inline Mixed Flow Fans 44

Manrose Classic Inline Hyper Fan 46

Manrose Classic Inline Axial Fans 48

Eco Inline Axial Fans 48

Manrose Classic Inline Centrifugal Fans 50

Simx Inline Centrifugal 3 Speed Fans 51

Simx Inline Centrifugal Fans 52

Simx WhisperVent inline Centrifugal Fans 54

Simx External Wall Mounted Fans 56

Thru-Roof Mounted Fans 58

Thru-Roof Mounted Fans 60

Specialised Fans 62

Fan Timers 63

Electronic Transformers 63

Isolating Transformers 63

Thermostats 64

Humidistat Controller 64

Speed Controllers 64

Fan Mounting Brackets 64

Kitchens

The regulations require a fan capable of a minimum extraction capacity of 50 litres per second when installed.

Laundries


Bathrooms


Toilets


EXTRACTION SELECTIONFAN REGULATIONS

INDUSTRY RECOMMENDATIONS

• The mentioned flow rates below are minimum allowable. In general these would not be enough to overcome excessive moisture and condensation problems encountered in modern homes.

• The ventilation industry has a “Recommended Air-Changes per Hour” approach solution. i.e. An air flow rate sufficient to remove/replace the total volume of air in a given room a specified number of times each hour.

• Obviously fans will not necessarily be left running for an hour - a fact which is taken into consideration in the formula.

Example:

A bathroom is recommended at between 11 & 15 air-changes per hour. Therefore 15 changes per hour means the total air in the room would be replaced after 4 minutes.

e.g. (60 minutes @ 15 changes per hour = 4 minutes).

This would mean an average bathroom usage of 12 - 16 minutes resulting in the total air volume being changed 3 to 4 times. This equates to a rate of 15 ACH.

WHAT THE LAW STATES

New Zealand Building Code G4 Ventilation (summarised):

“Buildings shall have a means of collecting or otherwise removing: cooking fumes and odours; steam from laundering, utensil washing, bathing and showering; odours from sanitary and waste storage spaces; poisonous or flammable fumes and gases”.

• Natural Ventilation for the above is acceptable as long as opening windows in each room have an area of 5% or more of the floor area of the room.

• For internal rooms without natural ventilation, mechanical ventilation (extraction fans) must be installed to extract the air at given rates. Residential requirements are listed below.

• Where fans are used to remove moisture and other contaminants from kitchens, bathrooms and laundries in housing, the exhaust air must be ducted to the outside at the flow rates mentioned below.

• The above requirement for ducting also applies to any fan in those areas, even if there is an opening window (i.e. even if the fan is not a requirement to comply with ventilation regulations, but is installed as an optional extra).

4

Damp air out

Fresh air in

Poor Circulation Medium Circulation

Window Closed

Window Closed

Best Circulation

“Makeup air” is required for the fan to function efficiently. This is simply air that replaces the air that has already been extracted and can be achieved with a gap under the door (min 5mm) or a grill in the door, we do not recommend opening a window.

MANAGING MOISTURE

It is best to remove moisture from where it is generated to outside the house before it has a chance to spread to other parts of the house.

Use ducted fans, through-wall fans or window fans at all times. DO NOT use ceiling fans which discharge into the ceiling cavity, this only moves the problem.

Moisture will permeate insulation and ceiling linings causing further problems. In particular with bathrooms think in terms of “room-conditioning”. Warm, moist air is immediately attracted to cold surfaces, where it condenses into water droplets.

Cold surfaces include glass, mirrors, tiles, wet-wall linings, cold un-insulated ceiling linings, etc.

You cannot remove all of this air at a rate fast enough to stop this happening and if you could, you would be standing in a wind tunnel. Use of a bathroom heater to warm the room prior to use greatly assists in reducing condensation.

FAN PLACEMENT

Careful location of an extraction fan will ensure maximum air-flow through the room. Air extracted from a bathroom, for example, can be replaced with dry

air drawn from an adjacent bedroom or hallway, in turn, drawn from an open window or door.

This ensures that fresh air is being drawn into the entire house at regular periods. Switching the fan on before starting showering or cooking sets up effective air-flows before condensation problems occur.

Closing doors to adjacent living areas assists in stopping the transfer of moisture to those areas but ensure that sufficient air can enter under the door to replace extracted air. Use a door vent if necessary.

For a fan to remove air effectively, the same amount of air being extracted must be able to enter the room, e.g. air in = air out. An air-tight room will mean no air movement. If the room is tightly sealed (e.g. a tight-fitting door, with no gap at the bottom), you may need to fit a through-door grille to allow replacement air into the room.

5Simx Limited | www.simx.co.nz | [email protected]

EXTRACTION SELECTIONYOUR EXTRACTION SOLUTIONS

400

350

300

250

200

150

100

50

0

110

100

90

80

70

60

50

40

30

20

10

240

220

200

180

160

140

120

100

80

60

40

20

m3/hr l/s cfm

Application Description Air Changes Per Hour

Bathrooms 11 - 15

Kitchens - (domestic) 15 - 20

Laundries - (no drier) 6 - 10

Laundries - (with drier) 10 - 30

Toilets 6 - 10

Bedroom 2 - 5

Offices 6 - 10

Cafés 10 - 12

Canteens 8 - 12

Garages 6 - 8

Kitchens - (commercial) 20 - 30

Restaurants 8 - 12

Factories 8 - 10

Stores & Warehouses 3 - 6

Libraries 3 - 5

Classroom 5 - 7

Example:

What is the best fan for a bathroom that is 2.8m long by 2.8m wide with a ceiling height of 2.4m?

• Calculate the volume of the bathroom: 2.8 x 2.8 x 2.4 = 18.8m3.

• 11-15 air changes per hour are recommended for a bathroom. Multiply the room volume by 15: 18.8m3 x 15 = 282m3/hr.

• The fan to choose for this bathroom would be a fan that performs at greater than 282m3/hr.

• A fan that has a performance level of 313m3/hr or higher (e.g. XP150, or SF150) would do this job.

AIR CHANGES PER HOUR (ACH)

The number of times the total room volume of air is changed each hour. Refer to the table below for the recommended Air Changes per hour based on the room type.

WORKING OUT THE RIGHT FAN FOR THE JOB

• Calculate the room volume in metres (L x W x H).

• Multiply the room volume by the recommended air changes per hour for that room. Always use the higher limit.

• The result is the total performance required in cubic metres per hour.

Select a fan with a higher performance than this figure.

m³/hr to l/s to cfm Comparison Chart

Known To Find Action

l/s m³/hr l/s x 3.6 =m³/hr

m³/hr l/s m³/hr ÷ 3.6 = l/s

cfm m³/hr cfm x 1.69 =m³/hr

cfm l/s cfm x 0.47 = l/s

QUICK CROSS-REFERENCE CALCULATIONS:

Convert from one to other types of measurement:

Note: Stated extraction rates are “free air” values and do not account for grille type or duct run restrictions.

CONVERTING LITRES/SECOND (L/S) AND CUBIC METRES/HOUR (M³/HR) (NOTE: 1M3 = 1000 LITRES)

If you know the Litres/Second (l/s):

l/s x 3.6 = m³/hr. (e.g. 25 l/s x 3.6 = 90m³/hr).

If you know the Cubic Metres/Hour (m³/hr):

m³/hr ÷ 3.6 = l/s. (e.g. 200m³/hr ÷ 3.6 = 55.55 l/s).

6

EXTRACTION SELECTIONCALCULATING EXTRACTION RATES

COMPARE CENTRIFUGAL AGAINST AXIAL FAN PERFORMANCE:

100mm (Axial) vs 100mm (Centrifugal) fan.

The starting point is the free air performance of 23 l/s for the axial and 31 l/s for the centrifugal. As duct is added to each of these fans, this increases the pressure (Pa) and decreases volume of air moved.

From the below example you can see that at 20Pa of pressure the 100mm axial fan airflow has stopped whereas the 100mm centrifugal fan is still moving 29 l/s!

Smaller duct = greater resistance to airflow. More bends = greater resistance to airflow. Longer duct runs = increasingly reduced airflow.

Manrose ALUDUCT flexible ducting retains its stretched-out shape (for smooth airflow) far better than most competitive products.

Many competitive ducts tend to shrink back on themselves, wrinkling the duct fabric.

FAN TYPES

Centrifugal: Pressure developing fans which achieve good flow against the resistance created in a ducted system. Particularly useful in venting areas like internal bathrooms/laundries, multi-room extraction systems, heat transfer systems, etc.

Mixed Flow: Powerful in-duct mounted fans, designed for applications that require high air flows, with low relative noise. Can handle more pressure than an axial fan, although not as powerful as a centrifugal fan.

Axial: Suitable for wall, window and roof applications where they can extract directly to the outside.

Short duct runs are an option but the length of duct should be limited, to those noted below:

100mm diameter : 2-3m length 125mm diameter : 3-4m length 150mm diameter : 4-5m length

150mm (Axial) vs 150mm (Centrifugal) fan.

The starting point is the free air performance of 89 l/s for the axial and 115 l/s for the centrifugal.

As duct is added to each of these fans, this increases the pressure (Pa) and decreases the volume of air moved. From the below example you can see that at 120 Pa of pressure the 150mm axial fan airflow has stopped whereas the 150mm centrifugal fan is still moving 102 l/s!

Wrinkled duct airflow

Wrinkled ducting causes turbulence and reduces airflow:

Volume l/sec

Sta

tic

pre

ssur

e P

a

Volume m3/hr

SF200

SF100

100mm (Axial) vs 100mm (Centrifugal)

*Graphs are a visual representation only.

SIMPLE FACTS

Smooth duct airflow

Smoother, extended ducting allows smooth, increased airflow:

*Graphs are a visual representation only.

50

150

100

200

250

300

0 20 40 60 80 100 120 140

0 72 144 216 288 360 432 504

0

350

Volume l/sec

Sta

tic

pre

ssur

e P

a

Volume m3/hr

MAN150

ID150

150mm (Axial) vs 150mm (Centrifugal)


EXTRACTION SELECTION

When considering where in the room to place an extractor fan, you must consider the wet areas.

Zone 1: This is the zone directly within the shower or bath up to 2.25 metres above the floor and 150mm around the bath/shower cubicle. A SELV fan or an inline fan kit will be required in this zone.

For example if a fan is mounted directly over the bath or shower it must be a low voltage fan (SELV).

Zone 2: This zone is 0.6 metres horizontally outside of zone 1 and up to 2.25 metres above the floor.

Zone 3: The outer layer is zone 3, which is 2.4 metres horizontally outside of zone 2 and 2.25 metres above the floor.

Requires a SELV Fan or an Inline fan kit.

Any fan model can be used.

Any fan model can be used.

Zone 1:

Zone 2:

Zone 3:

Select the model that exhausts the closest to your requirements.

If the performance required falls between two fans, it is recommended you select the one handling the most air, as grille type and duct run length will reduce the stated ‘free air’ performance.

8

EXTRACTION SELECTIONWET AREA ZONE GUIDE

Location of your extraction fan will depend on the physical constraints of your room. The wet area zone guide (shown on the previous page) will help you decide the most suitable physical installation to meet your requirements. Within the various mounting options there are other features available, such as:

• TIMER (maintain fan operation for a set time after the room is vacated).

• PULLCORD (switch at fan, instead of wall switch control).

• AUTO-SHUTTER (electrically operated shutters inside the fan - closed when the fan is not running to stop draughts).

• PIR SENSOR (provide automatic motion-sensor control of fans).

Ceiling Mounted Fan

Designed for low-pitch roofs or between floors, where there is no ceiling access. Also available with heat lamps & lighting.

Thru Wall Fan Kit

Used where the bathroom is on an external wall, or there is no ceiling space for an inline fan.

Window Mounted Fan

Used in situations where an existing window fan is being replaced, or where there is no available external wall space and no ceiling space access.

Inline Mounted Fan Kit

Most common bathroom installation, the fan is mounted in the ceiling space with the grille directly above the source of the steam.

Generally this type of installation is quieter as the fan is not directly in the room.

Thru Roof Kit

Used where there is limited access to the roof space, or where there is no soffit available. Thru Roof Kits can be used with any extraction fan, or use a Thru Roof Fan Kit with the fan mounted within the cowl.

Wall/Ceiling

Thru Wall

Heat/Fan/Light

Inline

Window


EXTRACTION SELECTIONFAN TYPES

Requires three wires: permanent phase, switched phase, neutral. NOTE: All fan flow rates quoted are free air delivery.

Switching Options

1. Standard - Operates from remote switch (not supplied).

2. Timer - Fan operates from a switch and continues to run for a preset time after switching off - adjustable 1-20 minutes.

Duct Size Model No. Switching Method Performance Order Code

125mm XFLP125SS Standard 36 l/s, 130m3/hr FAN0589

125mm XFLP125ST Timer 36 l/s, 130m3/hr FAN0590

150mm XFLP150SS Standard 101 l/s, 364m3/hr FAN0594

150mm XFLP150ST Timer 101 l/s, 364m3/hr FAN0595


125mm XFLP125CS Standard 36 l/s, 130m3/hr FAN0604

125mm XFLP125CT Timer 36 l/s, 130m3/hr FAN0605

150mm XFLP150CS Standard 101 l/s, 364m3/hr FAN0609

150mm XFLP150CT Timer 101 l/s, 364m3/hr FAN0610

CIRCULAR MODELS

SAFETY EXTRA LOW VOLTAGE (SELV) MODELS

• Unique low profile design enables these fans to be installed unobtrusively into any wall or ceiling.• These axial fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.

ACCESSORIES

Duct Size Square Facia Order Code

125mm Satin Silver Fascia FAN2068

125mm Chrome Fascia FAN0755



Duct Size Circular Facia Order Code





SQUARE MODELS


125mm XFLP125SLV Standard 36 l/s, 130m3/hr FAN5886

125mm XFLP125CLV Standard 36 l/s, 130m3/hr FAN5885

150mm XFLP150SLV Standard 101 l/s, 364m3/hr FAN5892

150mm XFLP150CLV Standard 101 l/s, 364m3/hr FAN5891

MANROSE PRO-SERIES WALL/CEILING MOUNTED FANSXFLP LOW PROFILE MODELS

Square Model

Circular Model

SELV Model

Satin Silver / Chrome Fascia

12VAC transformer included and suitable for installation in damp areas, zones 1, 2 and 3.

10

D

BC

A

A

A

Models A B C D

XFLP125S 161 122 10 118

XFLP125C 165 122 10 118

XFLP150S 191 122 10 150

XFLP150C 198 122 10 150

Models Circular Cut-Out Size

XFLP125S 140mm - Using gib fixing clips supplied/included

XFLP125C 140mm - Using gib fixing clips supplied/included

XFLP150S 173mm - Using gib fixing clips supplied/included

XFLP150C 173mm - Using gib fixing clips supplied/included

DIMENSION INFORMATION (MM)

TECHNICAL SPECIFICATION & PERFORMANCE DATA

Models XFLP125 XFLP150

Power 220 - 240V (SELV models 12V) 220 - 240V (SELV models 12V)

Fan Performance 36 l/s, 130m3/hr 101 l/s, 364m3/hr

Fan Wattage 20W 25W

Maximum Pressure 35 Pa 60 Pa

Fan Speed 2000 RPM 2400 RPM

Sound Level 41 dB(A) 40 dB(A)

Max. Operating Temp 50°C 50°C

IP Rating IPX4 IPX4

Performance - XFLP125 Performance - XFLP150

GENERAL INFORMATION


Duct Size Model No. Switching Performance Order Code

100mm XF100S Standard 23 l/s, 85m3/hr FAN0046

100mm XF100P Pull Cord 23 l/s, 85m3/hr FAN0047

100mm XF100T Timer 23 l/s, 85m3/hr FAN0048







150mm XF150PIR PIR Control 101 l/s, 364m3/hr FAN0124

AUTO SHUTTER MODELS


• Designed for wall or ceiling mounting, these models are efficient and easy to install.• These axial fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.

STANDARD MODELS

Standard Model

Safety Model (SELV)

Auto Shutter Model


100mm XF100LV Standard 23 l/s, 85m3/hr FAN5883




Switching Options


150mm XF150A Standard 87 l/s, 313m3/hr FAN0121

150mm XF150AP Pull Cord 87 l/s, 313m3/hr FAN0122

150mm XF150AT Timer 87 l/s, 313m3/hr FAN0123

Electrically operated louvre shutters open automatically when fan is running - prevents back-draughts.

12

MANROSE CLASSIC WALL/CEILING MOUNTED FANSXF MODELS



3. Pull Cord - Integral pull cord switch on fan.

4. PIR Control - Motion sensor incorporated in fan.NOTE: All fan flow rates quoted are free air delivery

A

B

CD

E

Dimensions - XF

Models A B C D E

XF100 155 98 74 27 155

XF125 168 118 74 27 168

XF150 200 148 74 27 200

XF150PIR 200 148 90 55 200

XF150A/AP 200 148 90 55 200



Models Circular Cut-Out Size

XF100 112mm

XF125 140mm

XF150 160mm

Please note: Fan cut out size is a nominal diameter.

Performance - XF100 Performance - XF125 Performance - XF150

GENERAL INFORMATION

Models XF100 XF125 XF150

Power 220 - 240V (LV models 12V) 220 - 240V (LV models 12V) 220 - 240V (LV models 12V)

Fan Performance 23/s, 85m3/hr 36 l/s, 130m3/hr 101 l/s, 364m3/hr*

Fan Wattage 20W 20W 25W

Maximum Pressure 20 Pa 35 Pa 60 Pa

Fan Speed 2400 RPM 2000 RPM 2400 RPM

Sound Level 41 dB(A) 41 dB(A) 40 dB(A)

Max. Operating Temp 50°C 50°C 50°C

IP Rating IPX4 IPX4 IPX4

*Auto shutter 87 l/s, 313m3/hr installed.



230mm XFS230S Standard 152 l/s, 550m3/hr FAN0374




230mm XFS230A Standard 152 l/s, 550m3/hr FAN0346

300mm XFS300A Standard 306 l/s, 1100m3/hr FAN2041

AUTO SHUTTER MODELS


230mm XPS230S Standard 152 l/s, 550m3/hr FAN0455

300mm XPS300S Standard 306 l/s, 1100m3/hr FAN2042

Commercial ModelsDuct Size Model No. Switching Performance Order Code

230mm XPS230A Standard 152 l/s, 550m3/hr FAN0348

300mm XPS300A Standard 306 l/s, 1100m3/hr FAN2043

Auto Shutter Models

Commercial Models

Auto Shutter Models

AUTO SHUTTER MODELS

MANROSE CLASSIC WALL/CEILING MOUNTED FANSXFS COMMERCIAL MODELS

MANROSE CLASSIC THRU WALL FAN KITSXPS COMMERCIAL MODELS

STANDARD MODELS

STANDARD MODELS

Switching Options


14

Models XFS230 XFS300 XPS230 XPS300

Power 220 - 240V 220 - 240V 220 - 240V 220 - 240V

Fan Performance 152 l/s, 550m³/hr 306 l/s, 1100m³/hr 152 l/s, 550m³/hr 306 l/s, 1100m³/hr

Fan Wattage 45W 82W 45W 82W

Maximum Pressure 50 Pa 60 Pa 50 Pa 60 Pa

Fan Speed 1250 RPM 1300 RPM 1250 RPM 1300 RPM

Sound Level 50 dB(A) 60 dB(A) 50 dB(A) 60 dB(A)

Max. Operating Temp 50°C 50°C 50°C 50°C

IP Rating IPX4 IPX4 IPX4 IPX4

Models A B C D E F G H I

XFS230 286 230 141 75 66 - - - -

XFS300 362 300 156 81 75 - - - -

XPS230 286 230 141 75 286 250 375 248 30

XPS300 362 300 156 81 350 230 375 298 50



Models Fan Cut-Out Size Exterior Grille Duct Type Duct Length

XFS230 265mm - - -

XFS300 310mm - - -

XPS230 265mm White Fixed Grille Aluminium Semi-Rigid 375mm

XPS300 310mm White Fixed Grille Aluminium Semi-Rigid 375mm


A

B

C

D

E

A

Dimensions - XF230/300

F AB

CD

E

G

H

I

Dimensions - XPS230/300

Performance - XFS230 Performance - XFS300

GENERAL INFORMATION


• Designed for apartments where space is limited, these ceiling mounted centrifugal fans can be installed in confined spaces.

• The centrifugal fan design assists ‘whisper quiet’ operation.• Reliable long lasting ball bearing motor.• FAN0884 & FAN0885 supported by a 2 year warranty. • FAN2465 supported by a 3 year warranty.

Duct Size Model No. Colour Performance Order Code

100mm WVC100W White 63 l/s, 225m3/hr FAN0884

100mm WVC100S Stainless 63 l/s, 225m3/hr FAN0885

150mm WVC150S White 101 l/s, 364m3/hr FAN2465

Simx WhisperVent 150 - White

Simx WhisperVent 100 - Silver

Simx WhisperVent 100 - White

16

SIMX WHISPERVENT CENTRIFUGAL CEILING FANSWVC MODELS

Models A B C D

WhisperVent 100 245 240 280 290

WhisperVent 150 315 330 355 370


Models WhisperVent 100 WhisperVent 150

Power 220 - 240V 220 - 240V


Fan Wattage 30W 42W




Max. Operating Temp 40oC 40oC

IP Rating IPX4 IPX4

Performance - WhisperVent 100

50 100 150 200 250

7515 30 45 60

20

40

60

0

80

100

120

140

160

200 40 60 80 100 120

500 100 150 200 250 300 350 400

Pre

ssur

e (P

a)

Volume (l/s)

Volume (m³/hr)

Performance - WhisperVent 150


Dimensions - WhisperVent

A - cut out size

D

B

C


3. PIR Control - Motion sensor incorporated in fan. Range up to 5 metres.NOTE: All fan flow rates quoted are free air delivery.

Switching Options


2. Timer - Fan operates from a switch and continues to run for a preset time after switching off - adjustable 1-20 minutes. Requires three wires: permanent phase, switched phase, neutral.

Duct Size Model No. SwitchingPerformance @ Speed 3

Order Code

100mm FFCF234S Standard 65 l/s, 234m3/hr FAN0038

100mm FFCF234T Timer 65 l/s, 234m3/hr FAN0499

100mm FFCF234PIR PIR Control 65 l/s, 234m3/hr FAN0501

SURFACE MOUNT RANGE


Order Code

100mm SMCF234S Standard 65 l/s, 234m3/hr FAN0504

100mm SMCF234T Timer 65 l/s, 234m3/hr FAN0505

• Designed for apartments where space is limited, with a choice of wall or ceiling mounted system.• These Models include centrifugal fans with a choice of three in-built speed settings depending

on the performance required.• Supported by a 2 year warranty.


Order Code

100mm CF200S Standard 31 l/s, 110m3/hr FAN0041

100mm CF200TP Timer 31 l/s, 110m3/hr FAN0042

• Designed to move air over long distances.• The centrifugal fan design provides efficient airflow and quiet operation.• Supported by a 2 year warranty.

Flush Fitting Range

CF Centrifugal Model

FLUSH FITTING RANGE

Surface Mount Range

18

MANROSE CLASSIC MULTI-VENT FANSFF/SM MODELS

MANROSE CLASSIC WALL FANSCF CENTRIFUGAL MODELS

Flush Fitting Range

Multi-Vent FFCF234 91 96 141 250 15 155 210 -

Multi-Vent SMCF234 312 250 15 119.5 22.5 63 249 -

CF200 65 65 185 260 45 98 90 135


1 Speed 2 Speed 3 Speed

Power 220 - 240V 220 - 240V 220 - 240V 220 - 240V

Fan Performance 28 l/s, 100m3/hr 45 l/s, 162m3/hr 65 l/s, 234m3/hr 31 l/s, 110m3/hr







NOTE: 1, 2, 3 refer to speed settings controlled by internal switch (not consumer adjustable).


A

B

C

D

E

GH

F

Dimensions - CF200

FA

B

CE

G

D

Dimensions - Multi-Vent (Surface Mount) Dimensions - Multi-Vent (Flush Fitting)

A

B

C

D

EG

D

G

F

Performance - Multi-Vent Performance - CF200



125mm XPLP125SS Standard 36 l/s, 130m3/hr FAN0614

125mm XPLP125ST Timer 36 l/s, 130m3/hr FAN0615

150mm XPLP150SS Standard 101 l/s, 364m3/hr FAN0621

150mm XPLP150ST Timer 101 l/s, 364m3/hr FAN0623


125mm XPLP125SLV Standard 36 l/s, 130m3/hr FAN5887

125mm XPLP125CLV Standard 36 l/s, 130m3/hr FAN5888

150mm XPLP150SLV Standard 101 l/s, 364m3/hr FAN5894

150mm XPLP150CLV Standard 101 l/s, 364m3/hr FAN5893

• The unique Low Profile design enables these fans to be installed unobtrusively into any wall (requires a minimum wall cavity of 110mm).

• These axial fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.

ACCESSORIES


Duct Size Square Fascia Order Code





Duct Size Circular Fascia Order Code



Low Voltage Models

Standard Models

Accessories - Circular Fascia

Accessories - Square

STANDARD MODELSKits include: ducting, exterior grille and fixtures.


Switching Options




20

MANROSE PRO-SERIES THRU WALL MOUNTED FAN KITSXPLP LOW PROFILE MODELS


XPLP125 161 118 128 10 160 125 375 123 30

XPLP150 191 150 132 10 174 150 375 148 30



Models XPLP125 XPLP150

Power 220 - 240V (LV models 12V) 220 - 240V (LV models 12V)


Fan Wattage 20W 25W





IP Rating IPX4 IPX4

Models Fan Cut-Out Size Exterior Grille Duct TypeDuct Length

XPLP125 140mm White Gravity Shutter Aluminium Semi-Rigid 375mm

XPLP150 173mm White Gravity Shutter Aluminium Semi-Rigid 375mm


FE

G

H

I

AB

CD

Dimensions - XPLP

Performance - XPLP125 Performance - XPLP150


GENERAL INFORMATION


100mm XP100S Standard 23 l/s, 85m3/hr FAN0053

100mm XP100P Pull Cord 23 l/s, 85m3/hr FAN0054

100mm XP100T Timer 23 l/s, 85m3/hr FAN0055







AUTO SHUTTER MODELS


150mm XP150A Standard 87 l/s, 313m3/hr FAN0136

150mm XP150AP Pull Cord 87 l/s, 313m3/hr FAN0137

150mm XP150AT Timer 101 l/s, 364m3/hr FAN0138

• These fans are designed to be ducted straight through an exterior wall and are efficient and easy to install.• These axial fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.



100mm XP100LV Standard 25 l/s, 85m3/hr FAN5882



Standard Models

Auto Shutter Models

Low Voltage Models

STANDARD MODELS

3. Pull Cord - Integral pull cord switch on fan.NOTE: All fan flow rates quoted are free air delivery.

Switching Options


2. Timer - Fan operates from a switch and continues to run for a preset time after switching off - adjustable 1-20 minutes. Requires three wires: permanent phase, switched phase, neutral.

Kits include: ducting, exterior cowl or grille and fixtures.



22

MANROSE CLASSIC THRU WALL MOUNTED FAN KITSXP MODELS

Performance - XP100 Performance - XP125 Performance - XP150


XP100 155 98 74 27 138 100 375 98 30

XP125 168 118 74 27 160 125 375 123 30

XP150 200 148 74 27 174 150 375 148 30

XP150A 200 148 90 55 174 150 375 148 30



Models Fan Cut-Out Size Exterior Grille Duct Type Duct Length

XP100 112mm Weatherproof Cowl Aluminium Semi-Rigid 375mm




F AB

CD

E

G

H

I

Dimensions - XP

Models XP100 XP125 XP150

Power 220 - 240V (SELV models 12V) 220 - 240V (SELV models 12V) 220 - 240V (SELV models 12V)

Fan Performance 23 l/s, 85m³/hr 36 l/s, 130m³/hr 101 l/s, 364m3/hr*







*Auto shutter 87 l/s, 313m3/hr installed.

GENERAL INFORMATION



100mm WF100P Pull Cord 23 l/s, 85m3/hr FAN0021

100mm WF100PLV Low Voltage 23 l/s, 85m3/hr FAN5884

AUTO SHUTTER MODELS

• Designed for use in situations where an existing window fan is being replaced or where there is no available external wall space or ceiling space access.


Standard Models

Auto Shutter Models

STANDARD MODELS

2. Pull Cord - Integral pull cord switch on fan..NOTE: All fan flow rates quoted are free air delivery.

Switching Options



150mm WF150AP Pull Cord 87 l/s, 313m3/hr FAN0107

150mm WF150APT Pull Cord Timer 87 l/s, 313m3/hr FAN0109

150mm WF150APLV Low Voltage 87 l/s, 313m3/hr FAN5897


12VAC transformer included with LV switching models and suitable for installation in damp areas, zones 1, 2 and 3.

12VAC transformer included with LV switching models and suitable for installation in damp areas, zones 1, 2 and 3.

24

MANROSE CLASSIC WINDOW MOUNTED FANSWF MODELS

Models A B C D

WF100 163 90 30 163

WF150 203 118 23 203



Models WF100 WF150

Power 220 - 240V 220 - 240V (SELV models 12V)

Fan Performance 23 l/s, 85m³/hr 87 l/s, 313m3/hr

Fan Wattage 20W 25W




Max. Operating Temp 50oC 50oC

IP Rating IPX4 IPX4

Models Glass Cut-Out Size

WF100 115mm - 155mm

WF150 165mm - 190mm

Please note: Glass cut out size is a nominal diameter for a circular cut-out.

A

BC

D

Dimensions - WF

Performance - WF100 Performance - WF150

GENERAL INFORMATION


COM MODELS

AUTO SHUTTER MODELS


300mm WF300A Standard 306 l/s, 1100m3/hr FAN0482

230mm WF230AP Pull Cord 152 l/s, 550m3/hr FAN0146


230mm COM230A Standard 185 l/s, 670m3/hr FAN0519

230mm COM230MP Pull Cord 185 l/s, 670m3/hr FAN0518

300mm COM300A Standard 280 l/s,1020m3/hr FAN0521

300mm COM300MP Pull Cord 280 l/s,1020m3/hr FAN0520

• Designed for use in situations where an existing window fan is being replaced or where there is no available external wall space or ceiling space access.

• These axial fans have ball bearing motors to prolong the life of the motor. • Supported by a 5 year warranty.




• Designed for commercial applications such as pubs, restaurants, hotels, shops etc. • These axial fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.

Standard Larger Models

Auto Shutter Models

Commercial Auto Shutter Models

STANDARD MODELS

Switching Options


26

MANROSE CLASSIC WINDOW COMMERCIAL FANSWF/COM MODELS


2. Pull Cord - Integral pull cord switch on fan.

NOTE: All fan flow rates quoted are free air delivery.

Models A B C D E

WF230 286 286 4-32 112 25

WF300 362 362 4-32 133 29

COM230 286 125 25 154 -

COM300 362 145 25 170 -

Models WF230 WF300 COM230 COM300

Power 220 - 240V 220 - 240V 220 - 240V 220 - 240V

Fan Performance 152 l/s, 550m3/hr 306 l/s, 1100m3/hr 185 l/s, 670m3/hr 280 l/s, 1020m3/hr








Models Glass Cut-Out Size

WF230 255mm - 270mm

WF300 310mm - 345mm

COM230 255mm - 270mm

COM300 310mm - 345mm

Please note: Glass cut out size is a nominal diameter for a circular cut-out.

A

B

C

D E

Dimensions - WF230/300

A

B

C

A

D

Dimensions - COM230/300

Performance - WF230 Performance - WF300

55

40

25

0

0 250 500 750

0 70 140 210

Stat

ic P

ress

ure

Pa

Volume l/sec

Volume m /hr3

55

40

25

0

0 83 168 250 333 416

0 300 600 900 1200 1500

Stat

ic P

ress

ure

Pa

Volume l/sec

Volume m /hr3

Performance - COM230 Performance - COM300

GENERAL INFORMATION


Duct Size Model No. Performance Order Code

150mm LED HFL 2 White 86 l/s, 310m3/hr FAN4463

150mm LED HFL 2 Silver 86 l/s, 310m3/hr FAN4464

150mm LED HFL 4 White 86 l/s, 310m3/hr FAN4465

150mm LED HFL 4 Silver 86 l/s, 310m3/hr FAN4466

ACCESSORIES

Description Order Code

275W Heat Lamp LHT0081

LED Replacement Lamp for Silver Units LHT0211

• With high levels of extraction, these units have a stylish low profile design, making them easy to install into tight fitting roof cavities.

• The units incorporate long-life energy efficient LED centre lamps.• Supported by a 5 year warranty.

Designer Series Heat ‘n Vent 4

Designer Series Heat ‘n Vent 2

28

MANROSE DESIGNER SERIES LED HEAT/FAN/LIGHT KITS

NOTE: All fan flow rates quoted with 3 metres of duct, one bend and one external grille (normal installation).

Models Cut-Out Size Exterior Grille Duct Type Duct Length

LED HFL 4 Slv 435mm x 275mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)

LED HFL 4 Wht 435mm x 275mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)

LED HFL 2 Slv 435mm x 255mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)

LED HFL 2 Wht 435mm x 255mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)


TECHNICAL SPECIFICATION

Models LED HFL 4 DLED HFL 2

Power 230 - 240V 230 - 240V

Fan Centrifugal Centrifugal

Fan Performance 86 l/s, 310m³/hr 86 l/s, 310m³/hr

Heat Lamps 4 x 275W 2 x 275W

Light GU10 LED GU10 LED

Total Wattage 1080 - 1180W 550 - 610W

Light Wattage 4 x 4.5W 3 x 4.5W

Switch Plate 4 sw. (supplied) 3 sw. (supplied)

A

B

C

D

A B

C

D

Dimensions - LED HFL 2Dimensions - LED HFL 4

Models A B C D

LED HFL 4 480 360 205 120*

LED HFL 2 480 290 205 120*

* 125mm to 150mm adapter included in kit.

GENERAL INFORMATION



150mm Heater Fan Light PANEL 69 l/s, 248m3/hr FAN6577

150mm Heater Fan Light HALO 69 l/s, 248m3/hr FAN5876

150mm Heater Fan Light PTC 22 l/s, 79m3/hr FAN5875

• Halogen or PTC Heaters.• Contemporary low profile linear design.• Complete system ready for ceiling installation.• Energy efficient LED lighting.

Heater Fan Light HALO

Heater Fan Light PTC

MANROSE DESIGNER SERIES HEATER FAN LIGHTS


These Designer Series Heater/Fan/Light units are designed to add functionality with flair to your bathroom. Systems feature low profile designs and supplementary LED lighting. All systems come with duct, grille and wall switch.

Heater Fan Light PANEL

30


Heater Fan Light PANEL 455mm x 305mm 150mm Eggcrate Aluduct 150mm x 3m

Heater Fan Light HALO 455mm x 305mm 150mm Eggcrate Aluduct 150mm x 3m

Heater Fan Light PTC 420mm x 275mm 100mm Eggcrate Aluduct 100mm x 3m


TECHNICAL SPECIFICATION

Models Heater Fan Light PANEL Heater Fan Light HALO Heater Fan Light PTC

Power 220 - 240V ~ 50Hz 220 - 240V ~ 50Hz 220 - 240V ~ 50Hz

Max Load 1100W 1100W 2250W

Fan Centrifugal Centrifugal Centrifugal

Fan Performance69 l/s (as installed with supplied components)

69 l/s (as installed with supplied components)

22 l/s (as installed with supplied components)

Heat 1 x 1000W Halogen 1 x 1000W HalogenPTC (Positive Temperature Coefficient)

Lamp2 x 12W LED Panels4000K

6 x 4.5W LEDsGU10 LED down light 3000K 38° degree

14W, 4000k White1000 Lumens

Switch Plate 3-Way Switch (supplied) 3-Way Switch (supplied) 4-Way Switch (supplied)

Heater Fan Light PTC

A

B

CD

Models A B C D

Heater Fan Light PANEL 500 350 200 150

Heater Fan Light HALO 500 350 200 150

Heater Fan Light PTC 450 300 185 100

GENERAL INFORMATION

Heater Fan Light PANEL

A

B

C

D

Heater Fan Light HALO

A

B

C

D


2 Heat ‘n Light

Classic Heat ‘n Vent 2

Pro-Series Heat ‘n Vent 2

MANROSE CLASSIC HEAT/LIGHT KITS2 HEAT ‘N LIGHT

MANROSE CLASSIC HEAT/FAN/LIGHT KITSHEAT ‘N VENT 2


125mm Heat ‘n Vent 4 60 l/s, 216m3/hr FAN0995


ACCESSORIES

Duct Size Description Order Code

125mm Heat ‘n Vent 4 Silver Fascia FAN1015

125mm Heat ‘n Vent 2 Silver Fascia FAN1014

275W Heat Lamp LHT0081

50W Halogen GU10 lamp LHT0140

• These systems meet the demands of larger bathrooms and the stylish fascia blends into the decor.

• These high efficiency centrifugal fans incorporate a unique anti-condensate design feature.

• Supported by a 5 year warranty.




100mm 2 Heat ‘n Light (excludes fan) FAN2200

• This system delivers instant heat combined with ventilation and soft lighting to create a comfort area in small bathrooms.


• This system provides instant heat and additional lighting.• For a complete bathroom solution an extraction fan can be added.• Supported by a 5 year warranty.


32

MANROSE PRO-SERIES HEAT/FAN/LIGHT KITSHEAT ‘N VENT MODELS


Models A B C D

PS Heat ‘n Vent 4 338 338 170 120

PS Heat ‘n Vent 2 435 260 185 120

Heat ‘n Vent 450 250 195 100

Heat ‘n Light 450 250 195 100


PS Heat ‘n Vent 4 300mm x 300mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)

PS Heat ‘n Vent 2 390mm x 210mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)

Classic Heat ‘n Vent 2 390mm x 220mm White Eggcrate Aluminium 3m supplied (you can add up to 3m extra duct)

Classic Heat ‘n Light 390mm x 220mm - - -



Models PS Heat ‘n Vent 4 PS Heat ‘n Vent 2 Heat ‘n Vent 2 2 Heat ‘n Light

Power 220 - 240V 220 - 240V 220 - 240V 220 - 240V

Fan Centrifugal Centrifugal Centrifugal -

Fan Performance 60 l/s, 216m³/hr 50 l/s, 180m³/hr 35 l/s, 126m³/hr -

Heat Lamps 4 x 275W 2 x 275W 2 x 275W 2 x 275W

Light GU10 Halogen GU10 Halogen GLES GLES

Total Wattage 1180W 635W 670W 650W

Light Wattage 50W 50W 100W 100W

Switch Plate 4 sw. (supplied) 3 sw. (supplied) 3 sw. (supplied) 2 sw. (supplied)

Dimensions - PS Heat ‘n Vent 2

A

B

C

D

Dimensions - PS Heat ‘n Vent 4

A B

C

Dimensions - Classic Heat ‘n Vent

D

B

C

A

D

B

C

Dimensions - Classic 2 Heat ‘n Light

72 144 180 216 252 28810836

70

Performance Graph



Classic Heat ‘n Vent 203010203


GENERAL INFORMATION


100mm MFLP100S Standard 69 l/s, 250m3/hr FAN2049



• These powerful inline mixed flow fans have been designed to produce higher working pressures for applications that require higher airflows with low relative noise levels.


MFLP150

Models Grille Cut-Out Interior Grille Exterior Grille Duct Type Duct Length

MFLP100 115mm White Low Profile White Low Profile Unilok Nude6m supplied (you can add up to 6m extra duct)



Please note: Grille cut out size is a nominal diameter for a circular cut-out.

GENERAL INFORMATION

Switching Options

34

MIXFLO PRO-SERIES INLINE FAN KITSSHOWER FAN MODELS


Models A B C D E F G

MF100 98 182 315 100 100 168 27

MF125 122 182 350 100 100 168 60

MF150 147 209 360 130 115 195 55


Model NoSound Power Levels Lw (dB)Octave band centre frequency in Hz LwA dB(A)

125 250 500 1000 2000 4000 8000

MF100 50 56 58 58 52 47 37 61

MF125 52 59 60 60 56 49 41 63.5

MF150 58 66 65 63 62 54 46 67.5

SOUND POWER LEVELS (HIGH SPEED)

Dimensions - MF

Model NoSize (mm)

RPM WattsMaximum Airflow (m³/hr)

Maximum Pressure (Pa)

Lp dB(A)3m*

IPRating

Max Operating Temp °C

MF100 1002300 40 250 180

40 X4 451700 18 190 120

MF125 1252300 40 320 220

43 X4 451700 18 260 160

MF150 1502700 70 597 300

47 X4 602000 60 330 240

* Lp dB(A) @ 3 metres - sound pressure based on the high speed for each fan.

0

20

40

60

80

100

120

140

160

180

200

0 20 40 60 80

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0 50 100 150 200 250 300

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0 50 100 150 200 250 300 350

0

50

100

150

200

250

0 20 40 60 80 100

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0

50

100

150

200

250

300

350

0 50 100 150 200

0 100 200 300 400 500 600 700

Performance - MF100 Performance - MF125 Performance - MF150

A B

CD

E

FG



Duct Size Model No. Switching Fan Type Performance Order Code

125mm SFLP125S Standard Ctr’fgl 39 l/s, 140m³/hr FAN0616

125mm SFLP125T Timer Ctr’fgl 39 l/s, 140m³/hr FAN0617

150mm SFLP150S Standard Hyper150 109 l/s, 394m³/hr FAN0618

150mm SFLP150T Timer Hyper150 109 l/s, 394m³/hr FAN0619

• These high efficiency inline fans are designed to provide higher levels of extraction for today’s larger bathrooms.


SFLP150

ModelsGrille Cut-Out

Interior Grille Exterior Grille Duct Type Length of duct included

SFLP125 140mmWhite Low Profile options

Weatherproof Cowl or Fixed insert option

Flexible PVC4m supplied (can be extended up to 6m)

SFLP150 160mmWhite Low Profile options

Weatherproof Cowl or Fixed insert option

Flexible PVC5m supplied (can be extended up to 6m)


GENERAL INFORMATION

between 1-20 minutes, whereas the 150mm models include a fixed 7 minute timer. Both require: permanent phase and switched phase. NOTE: All fan flow rates quoted are free air delivery.

Performance will be affected by the length of ducting used.

Switching Options


2. Timer - Fan operates from a switch and continues to run for a preset time after switching off. The 100 and 125mm models are adjustable

36

MANROSE PRO-SERIES INLINE MOUNTED FAN KITSSFLP SHOWER FAN MODELS

Models A B C D E

SFLP125 155 125 125 195 258

SFLP150 200 143 170 185 -


Models SFLP125 SFLP150

Fan CFD225 Hyper150

Power 220 - 240V 220 - 240V


Fan Wattage 20W 27W





IP Rating IPX4 IPX2

AB CD

E

A

B

C

D

Dimensions - SFLP125 Dimensions - SFLP150

Performance - SFLP125 Performance - SFLP150


0

20

40

60

80

100

120

140

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (l/s)


Duct Size Model No.Switching Method

Fan Type Performance Order Code

100mm SF100S Standard Axial 23 l/s, 85m3/hr FAN0017

100mm SF100T Timer Axial 23 l/s, 85m3/hr FAN0018

100mm SF200S Standard Ctr’fgl 31 l/s, 110m3/hr FAN0328

100mm SF200T Timer Ctr’fgl 31 l/s, 110m3/hr FAN0329

125mm SF125S Standard Axial 36 l/s, 130m3/hr FAN0064

125mm SF125T Timer Axial 36 l/s, 130m3/hr FAN0065

150mm SF150S Standard Hyper 109 l/s, 394m3/hr FAN0101

150mm SF150T Timer Hyper 109 l/s, 394m3/hr FAN0102

• With the fan mounted in the ceiling space, these inline models are able to draw steam directly from source.

• These fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.

FAN0101

GENERAL INFORMATION


Models Grille Cut-Out Interior Grille Exterior Grille Duct Type Length of duct included

SF100 115mm White Round White Fixed Louvre Flexible PVC3m supplied (should not be extended)

SF200 115mm White Round White Fixed Louvre Flexible Alum3m supplied (can be extended up to 6m)

SF125 140mm White Round White Fixed Louvre Flexible PVC4m supplied (should not be extended)

SF150 160mm White Round White Fixed Louvre Flexible PVC5m supplied (can be extended up to 6m)

between 1-20 minutes, whereas the 150mm models include a fixed 7 minute timer. Both require: permanent phase and switched phase.NOTE: All fan flow rates quoted are free air delivery.


Switching Options



38

MANROSE CLASSIC INLINE MOUNTED FAN KITSSF SHOWER FAN MODELS

Models A B C D E

SF100 130 155 90 100 27

SF200 155 100 100 195 258

SF125 150 155 99 118 27

SF150 200 143 170 185 -


Models SF100 SF200 SF125 SF150

Fan ID100 CFD200 ID125 Hyper

Power 220 - 240V 220 - 240V 220 - 240V 220 - 240V

Fan Performance 23 l/s, 85m³/hr 31 l/s, 110m³/hr 36 l/s, 130m³/hr 109 l/s, 394m3/hr





Max Operating Temp 50°C 50°C 50°C 60°C


Note: PERFORMANCE - ID Fans maximum fan performance stated, this can vary depending on the length of ducting used.

A

B

C

D

E

AB CD

E

Dimensions - SF100/SF125

Dimensions - SF200

A

B D

CA

B

C

D

Dimensions - SF150

Performance - SF100 Performance - SF200Performance - SF125

Performance - SF150

0

20

40

60

80

100

120

140

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (l/s)



Halogen Model

Fits Model Diffuser Colour Order Code

ELLP150 Incl Halogen White DCT1521

ELLP150 Incl Halogen Silver DCT1522

ELLP125 Incl Halogen White DCT1519

ELLP125 Incl Halogen Silver DCT1520

LED Model


ELLP150 Incl LED & Driver White DCT3211

ELLP150 Incl LED & Driver Silver DCT3212

ELLP125 Incl LED & Driver White DCT3213

ELLP125 Incl LED & Driver Silver DCT3214

ELLPS150 Incl LED & Driver White DCT3640

Switching Options

• These high efficiency inline fans are designed to provide higher levels of extraction for larger bathrooms.

• Choose either an energy efficient LED or halogen lamp.• White or satin silver finish available to complement your bathroom decor.• Supported by a 5 year warranty.

Duct Size

Model Switching PerformanceOrder CodeHalogen / LED

125mm ELLP125WS - Wht Standard 39 l/s, 140m3/hr FAN2029 / FAN5379

125mm ELLP125WT - Wht Timer 39 l/s, 140m3/hr FAN2031 / FAN5381

125mm ELLP125SS - Slv Standard 39 l/s, 140m3/hr FAN2030 / FAN5380

125mm ELLP125ST - Slv Timer 39 l/s, 140m3/hr FAN2032 / FAN5382

150mm ELLP150WS - Wht Standard 109 l/s, 394m3/hr FAN2033 / FAN5375

150mm ELLP150WT - Wht Timer* 109 l/s, 394m3/hr FAN2035 / FAN5377

150mm ELLP150SS - Slv Standard 109 l/s, 394m3/hr FAN2034 / FAN5376

150mm ELLP150ST - Slv Timer* 109 l/s, 394m3/hr FAN2036

150mm ELLPS150WS - Wht SQ Standard 109 l/s, 394m3/hr FAN5899

150mm ELLPS150WT – Wht SQ Timer* 109 l/s, 394m3/hr FAN5900

* Includes a 7 minute fixed timer.

ACCESSORIES

Halogen/LED ELLP125SW

Halogen/LED ELLP150SS

GENERAL INFORMATION

ModelsDiffuser Cut-Out

Interior Exterior Grille Duct Type Length of duct included

ELLP125 140mmWhite or Satin Silver Extract-a-lite

White Low Profile Black Unilok6m supplied (you can add up to 6m extra duct)

ELLP150 165mmWhite or Satin Silver Extract-a-lite

White Low Profile Black Unilok6m supplied (you can add up to 6m extra duct)

Please note: Diffuser cut out size is a nominal diameter for a circular cut-out.

LED-ELLP150 Diffuser White

LED-ELLPS150 Diffuser White





40

MANROSE PRO SERIES INLINE FAN/LIGHT KITSELLP EXTRACT-A-LITE/LED LOW PROFILE MODELS

Models A B C D E F G H

ELLP125 155 125 125 195 258 165 80 110

ELLP150 200 143 170 185 - 200 80 148


Models ELLP125 ELLP150

Fan CFD225 Hyper

Power 220 - 240V 220 - 240V


Fan Wattage 20W 27W



Light 12V 50W Halogen 12V 50W Halogen

12V 3W LED 12V 3W LED

Total Wattage 99W 96W



IP Rating IPX4 IPX2

F

G

H

AB CD

E

Dimensions - ELLP125 Fan

A

B D

CA

B

C

D

Dimension - ELLP150 Fan Dimensions - ELLP Extract-a-lite Diffuser

Performance - ELLP125


0

20

40

60

80

100

120

140

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (l/s)

Performance - ELLP150


Halogen Model


EL150 Incl Halogen White DCT1169

EL150 Incl Halogen Chrome DCT1171





LED Model


EL150 Incl LED & Driver White DCT3209

EL150 Incl LED & Driver Chrome DCT3208







Switching Options



ACCESSORIES

• The fan is mounted in the ceiling space, and is therefore able to draw steam directly from source, while at the same time providing spot lighting within your bathroom.

• Choose either an energy efficient LED or halogen lamp.• These fans have ball bearing motors to prolong the life of the motor.• Supported by a 5 year warranty.

Halogen/LED EL150S

ModelsDiffuser Cut-Out

Interior Exterior Grille Duct Type Length of Duct included

EL100 115mmWhite or Chrome Extract-a-lite

White Eggcrate Flexible PVC 3m supplied (should not be extended)


White Eggcrate Flexible PVC 4m supplied (should not be extended)


White Eggcrate Flexible PVC 5m supplied (you can add up to 6m extra duct)

Please note: Diffuser cut out size is a nominal diameter for a circular cut-out.

GENERAL INFORMATION

Duct Size

Model Switching PerformanceOrder CodeHalogen / LED

100mm EL100S Standard 31 l/s, 110m3/hr FAN0420 / FAN5373

100mm EL100T Timer 31 l/s, 110m3/hr FAN0438 / FAN5374


125mm EL125T Timer 36 l/s, 130m3/hr FAN2038 / FAN5372


150mm EL150T Timer* 109 l/s, 394m3/hr FAN0804 / FAN5370

* Includes a 7 minute fixed timer.

125mm Halogen-EL Diffuser Chrome

150mm LED-EL Diffusers White

42

MANROSE CLASSIC INLINE FAN/LIGHT KITSEL EXTRACT-A-LITE/LED MODELS

F

G

H

0

20

40

60

80

100

120

140

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (l/s)

Models A B C D E F G H

EL100 130 155 90 100 27 140 74 98

EL125 150 155 99 118 27 170 74 118

EL150 200 143 170 185 - 200 74 148


Dimensions - EL Extract-a-lite Diffuser

Performance - EL100 Performance - EL125 Performance - EL150

Models EL100 EL125 EL150

Fan CFD200 ID125 Hyper

Power 220 - 240V 220 - 240V 220 - 240V

Fan Performance 31 l/s, 110m3/hr 36 l/s, 130m3/hr 109 l/s, 394m³/hr




Light 12V 50W Halogen 12V 50W Halogen 12V 50W Halogen

12V 3W LED 12V 3W LED 12V 3W LED

Total Wattage 70W 75W 88W





A

B D

C

Dimensions - EL150 FanDimensions - EL100

AB CD

E

Dimensions - EL125

A

B

C

D

E


Duct Size Model No. Switching Speed Setting

Performance @ High Speed

Order Code

100mm MF100S Standard 2 Speed 69 l/s, 250m3/hr FAN1004

100mm MF100T Timer 2 Speed 69 l/s, 250m3/hr FAN2124

100mm MF100PL Plug & Lead 2 Speed 69 l/s, 250m3/hr FAN1050









• These powerful inline mixed flow fans have been designed to produce higher working pressures for applications that require higher airflows with low relative noise levels.

• Supported by a 4 year warranty or 30,000 continuous hours.


MixFlo 150mm Standard Model - White

Dimensions - MF

D

E

F

AB

C

GModelsDimensions

A B C D E F G

MF100 98 182 315 100 100 168 27

MF125 122 182 350 100 100 168 60

MF150 147 209 360 130 115 195 55

MF200 197 244 354 142 140 230 50




Switching Options

44

MIXFLO PRO-SERIES INLINE MIXED FLOW FANSFAN MODELS

0

20

40

60

80

100

120

140

160

180

200

0 20 40 60 80

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0 50 100 150 200 250 300

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0 50 100 150 200 250 300 350

0

50

100

150

200

250

0 20 40 60 80 100

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0

50

100

150

200

250

300

350

0 50 100 150 200

0 100 200 300 400 500 600 700

Performance - MF100 Performance - MF125 Performance - MF150

Pre

ssur

e (P

a)

Airflow (L/s)

Airflow (m3/hr)

0 200 400 600 800 1000

0

50

100

150

200

250

300

0 50 100 150 200 250 300*MF200 Timer model only has 2 speeds, therefore Medium fan speed specifications will not apply.

Performance - *MF200

Speed 1 Speed 2 Speed 3

Icon Key

Model NoSize (mm)

RPM WattsMaximum

Airflow (m³/hr)Maximum

Pressure (Pa)Lp dB(A)

3m*IP

RatingMax Operating

Temp °C

MF100 1002300 40 250 180 40

33X4 45

1700 18 190 120

MF125 1252300 40 320 220 43

36X4 45

1700 18 260 160

MF150 1502700 70 597 300 47

40X4 60

2000 60 330 240

MF200 200

2700 85 980 250 48

45

41

X4 602350 60 860 140

2000 45 706 80

* Lp dB(A) @ 3 metres - sound pressure based on the high speed for each fan.


SOUND POWER LEVELS

Model No.

Sound Power Levels LwA (dB) Octave band centre frequency in Hz

125 250 500 1000 2000 4000 8000

MF100 50 56 58 58 52 47 37

MF125 52 59 60 60 56 49 41

MF150 58 66 65 63 62 54 46

MF200 65 69 64 63 62 60 48


Switching Options

1. Standard - Operates from remote switch (not supplied).NOTE: All fan flow rates quoted are free air delivery.

MANROSE CLASSIC INLINE HYPER FAN


150mm Hyper150 Standard 109 l/s, 394m3/hr FAN0085

• This high efficiency inline fan is designed to provide high levels of extraction.• The ball bearing motor prolongs the life of the motor.• Includes 1.3m lead and 3 pin plug.• Supported by a 5 year warranty.

Hyper 150

BELIEVE THE HYPENew Zealand’s best selling, most trusted and trade preferred fan is now better than ever

ManroseHYPER150✔ Stronger: 394 m3/hour✔ Quieter: 38 dB(a)✔ MORE ENERGY EFFICIENT

THE IMPROVED HYPER FAN IS ALSO USED IN THESE SHOWER FAN KITS: • Manrose ProSeries Shower Fans Kits inc FAN0618• Manrose ProSeries Extract-A-LED Shower Fan Kit inc FAN5375• Manrose Classic Shower Fan Kits inc FAN0101 • Manrose Classic Extract-A-Lite Kits inc FAN0803 • Manrose Classic Extract-A-LED Kits inc FAN5369• HeatTrans One Room Kit FAN0325

46


Hyper150 200 143 170 185A

B

C

D

Dimensions


Power 220-240 V ~ 50Hz

Fan Performance 109 l/s, 394m³/hr

Fan Wattage 27W

Maximum Pressure 120 Pa

Sound Level 38dB

IP Rating IPX2

Performance - Hyper150

0

20

40

60

80

100

120

140

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (l/s)



100mm ID100S Standard 23 l/s, 85m3/hr FAN0012

100mm ID100T Timer 23 l/s, 85m3/hr FAN0013







• With the fan mounted in the ceiling space, these inline models are able to draw steam directly from the source.


ID100/125/150

ID230


150mm ECO150S Standard 64 l/s, 230m3/hr FAN2078

• With the fan mounted in the ceiling space, these inline models are able to draw steam directly from the source.

• High quality sleeve bearing motor.• Supported by a 2 year warranty.

ECO150S

Switching Options

48



Requires three wires: permanent phase, switched phase, neutral.NOTE: All fan flow rates quoted are free air delivery.

ECO INLINE AXIAL FANS

MANROSE CLASSIC INLINE AXIAL FANSID MODELS

Models A B C D E

ID100 130 155 90 100 27

ID125 150 155 99 118 27

ECO150 (white) 187 153 109 150 27

ID150 187 153 109 150 27

ID230 (square model) 286 286 155 230 -


Models ID100 ID125 ECO150 ID150 ID230

Power 220 - 240V 220 - 240V 220 - 240V 220 - 240V 220 - 240V

Fan Performance 23 l/s, 85m³/hr 36 l/s, 130m³/hr 64 l/s, 230m³/hr 87 l/s, 313m³/hr 152 l/s, 550m³/hr

Fan Wattage 20W 20W 25W 25W 80W

Maximum Pressure 20 Pa 35 Pa 50 Pa 60 Pa 50 Pa

Fan Speed 2400 RPM 2000 RPM 2400 RPM 2400 RPM 1250 RPM

Sound Level 41 dB(A) 41 dB(A) 40 dB(A) 40 dB(A) 50 dB(A)

Max. Operating Temp 50°C 50°C 50°C 50°C 50°C

IP Rating IPX4 IPX4 IPX4 IPX4 IPX4

Dimensions - ID Fans

Performance - ID100 Performance - ID125 Performance - ECO150

Performance - ID150 Performance - ID230

Note: PERFORMANCE - ID Fans maximum fan performance stated, this can vary depending on the length of ducting used.

DIMENSIONS SPECIFICATION (MM)

A

B

C

D

E


Requires: permanent phase and switched phase.NOTE: All fan flow rates quoted are free air delivery.

Switching Options




100mm CFD200S Standard 31 l/s, 110m³/hr FAN0326

100mm CFD200T Timer 31 l/s, 110m³/hr FAN0327

125mm CFD225S Standard 39 l/s, 140m³/hr FAN2067

125mm CFD225T Timer 39 l/s, 140m³/hr FAN2066

• These high efficiency centrifugal fans are designed for use where longer duct runs are required.

• These centrifugal fans have ball bearing motor prolongs the life of the motor.


Dimensions - CFD200/CFD225

Performance - CFD200 Performance - CFD225

CFD200S

Models CFD200 CFD225

Power 220 - 240V 220 - 240V


Fan Wattage 20W 20W

Maximum Pressure 120Pa 120Pa




IP Rating IP44 IPX4

Models A B C D E

CFD200 155 100 100 195 258

CFD225 155 125 125 195 258

DIMENSION INFORMATION (MM)TECHNICAL SPECIFICATION

AB CD

E

50

MANROSE CLASSIC INLINE CENTRIFUGAL FANSCFD MODELS

Duct Size Model No. Performance @ Speed 3 Order Code

150mm 3 Speed 124 l/s, 445m³/hr FAN0921

200mm 3 Speed 208 l/s, 750m³/hr FAN0997

• Suitable for a variety of domestic and commercial applications, these inline centrifugal fans provide high performance at your preset choice of speed.


Please note: Can be used for supply or extract.

Models A B C D E

150mm 340 150 280 50 75

200mm 340 200 280 50 75


Models 150mm 200mm

Voltage/Freq (50hz) 220 - 240V 220 - 240V

Fan Performance Speed 1 72 l/s, 260m³/hr 120 l/s, 433m³/hr



Fan Wattage (at high speed) 57W 105W

Current (A) (at high speed) 0.26 0.47

Fan Speed (at high speed) 2450 RPM 2500 RPM

Sound Level* 43 dB(A) 56 dB(A)

Ambient Temp 50°C 70°C

* dB(A) - measured 1m free field.

Performance - 150mm 3 Speed

400

300

200

100

0

Pre

ssu

re (

Pa

)

500 100 150 200

Volume (m3/hr)

Volume l/s

1000 200 300 400 500 600 700 800

Performance - 200mm 3 Speed

Dimensions - Simx Inline Centrifugal 3 Speed Fan

DIMENSION INFORMATION (MM)Simx Inline Centrifugal 3 Speed Fan


SIMX INLINE CENTRIFUGAL 3 SPEED FANSHIGH PERFORMANCE MODELS

Duct Size Model No Performance Order Code

100mm MAN100 49 l/s, 176m3/hr FAN0361

125mm MAN125 61 l/s, 220m3/hr FAN0360

150mm MAN150 124 l/s, 445m3/hr FAN0330

200mm MAN200 208 l/s, 750m3/hr FAN0467

250mm MAN250 280 l/s, 1010m3/hr FAN0358

315mm MAN315 360 l/s, 1300m3/hr FAN0357

315mm MAN315L 472 l/s, 1700m3/hr FAN0356

• Suitable for a variety of domestic and commercial applications, these inline centrifugal fans provide extremely high performance with a choice of sizes.


Please note: Can be used for supply/extract.

Models A B C D E

MAN100 250 100 136 50 70

MAN125 250 125 147 60 60

MAN150 340 150 280 50 75

MAN200 340 200 280 50 75

MAN250 341 249 230 30 30

MAN315 405 315 275 30 30

MAN315L 405 315 275 30 30


Dimensions - Simx 150mm Inline Fan

Simx 150mm Inline Fan

52

SIMX INLINE CENTRIFUGAL FANSHIGH PERFORMANCE MODELS

Models MAN100 MAN125 MAN150 MAN200 MAN250 MAN315 MAN315L

Voltage/Freq (50hz) 220-240V 220-240V 220-240V 220-240V 220-240V 220-240V 220-240V

Fan Performance49 l/s, 176m³/hr

61 l/s, 220m³/hr

124 l/s, 445m³/hr

208 l/s, 750m³/hr

280 l/s, 1010m³/hr

360 l/s, 1300m³/hr

472 l/s, 1700m3/hr

Fan Wattage 32W 31W 57W 105W 170W 176W 318W

Maximum Pressure 153 Pa 143 Pa 320 Pa 418 Pa 500 Pa 590 Pa 720 Pa

Current (A) 0.14 0.13 0.26 0.47 0.76 0.77 1.39

Fan Speed (min -1) 2500 RPM 2490 RPM 2450 RPM 2500 RPM 2580 RPM 2387 RPM 2433 RPM

Sound Level* 38 dB(A) 38 dB(A) 50 dB(A) 47 dB(A) 48 dB(A) 52 dB(A)

Max Operating Temp 60°C 60°C 50°C 70°C 50°C 60°C 40°C

* dB(A) - measured 1m free field.


200mm

Volume l/s

Volume m3/h

0

50

100

150

200

250

300

350

400

450

0 50 100 150 200 250

0 100 200 300 400 500 600 700 800 900

Sta

tic

Pre

ssur

e (P

a)

Performance - MAN200 Performance - MAN250 Performance - MAN315 & MAN315L

250mm

0

50

100

150

200

250

300

350

400

450

500

0 50 100 150 200 250 300

0 200 400 600 800 1000

Volume l/s

Volume m3/h

Sta

tic

Pre

ssu

re (P

a)

250mm

MAN315

MAN315L

0

100

200

300

400

500

600

0 50 100 150 200 250 300 350 400

0 200 400 600 800 1000 1200 1400

Volume l/s

Volume m3/h

Sta

tic

Pre

ssur

e (P

a)

Performance - MAN100 Performance - MAN125 Performance - MAN150

100mm 125mm

Volume l/s

Volume m3/h

Volume l/s

Volume m3/h

0

20

40

60

80

100

120

140

160

0

20

40

60

80

100

120

140

160

0 10 20 30 40 50

0 50 100 150 200 250

0 10 20 30 40 50 60 70

0 20 40 60 80 100 120 140 160 180

Sta

tic

Pre

ssu

re (P

a)

Sta

tic

Pre

ssu

re (P

a)

100mm 125mm

Volume l/s

Volume m3/h

Volume l/s

Volume m3/h

0

20

40

60

80

100

120

140

160

0

20

40

60

80

100

120

140

160

0 10 20 30 40 50

0 50 100 150 200 250

0 10 20 30 40 50 60 70

0 20 40 60 80 100 120 140 160 180

Sta

tic

Pre

ssu

re (

Pa

)

Sta

tic

Pre

ssu

re (

Pa

)

200mm150mm

Volume l/s

Volume m3/h

0

50

100

150

200

250

300

3500 50 100 150 200 250 300 350

0 20 40 60 80 100 120

Sta

tic

Pre

ssur

e (P

a)

400


Duct Size Model No Performance Order Code

150mm WVILP150-1 124 l/s, 445m3/hr FAN0829

150mm WVILP150-3 124 l/s, 445m3/hr FAN0830

• Suitable for a variety of domestic and commercial applications, this inline centrifugal fan offers high performance with a low profile design to enable this unit to be installed in confined spaces.



Models A B C D E

WhisperVent Low Profile 313 168 148 340 218

Dimensions

A

E

B

D

Ø C

Simx 150mm WhisperVent low profile

54

SIMX WHISPERVENT INLINE CENTRIFUGAL FANSLOW PROFILE MODELS

Model No

Sound Power Levels Lw (A)Octave band centre frequency in Hz dB(A) @ 3m63 125 250 500 1k 2k 4k 8k

FAN0830 - Speed 1 - 20 34 43 43 44 40 30 30

FAN0830 - Speed 2 - 26 40 51 51 52 45 38 36

FAN0830 - Speed 3 - 40 42 62 64 64 59 45 43

FAN0829 57 61 68 67 65 64 59 53 43

SOUND POWER LEVEL

ModelsFan Speed

Fan PerformanceNorm Fan

Speed (RPM)

Single Phase

Nom Watts Nom Amps

FAN0830 1 72 l/s, 260m³/hr 1440 50 0.22

FAN0830 2 102 l/s, 367m³/hr 1860 56 0.24

FAN0830 3 124 l/s, 445m³/hr 2460 80 0.36

FAN0829 1 124 l/s, 445m³/hr 2450 80 0.36


Performance - FAN0829 & FAN0830

400

300

200

100

Sta

tic

Pre

ssur

e P

a

28 56 83 111 139 167 194 222 250 278

Volume (l/s)

100 200 300 400 500 600 700 800 900 1000Volume (m3/hr)

12

3FAN0829



110mm

369mm

305mm

C

A

B

Connection

1. Electrical connection must be made internally (Junction Box is only suitable for internal use).NOTE: All fan flow rates quoted are free air delivery.

SIMX EXTERNAL WALL MOUNTED FANS3 SPEED EXTRACT MODELS

*Also available in a Supply Air option

Duct Size Fan Type Air Performance Order Code

150mm Axial Extract* 73 l/s, 263m3/hr FAN2303

150mm Ctr’fgl (190 Motor) Extract 109 l/s, 392m3/hr FAN2301


Duct Size Fan Type AirPerformance(High Speed)

Order Code



• Designed for use in residential and light commercial applications where a high performance, low noise solution is required.

• Specific applications include apartments where space is limited.• Supported by a 2 year warranty.

• Designed for use in residential and light commercial applications where a high performance, low noise solution is required.

• Three speed models enable further flexibility in a variety of applications.• Specific applications include apartments where space is limited.• Supported by a 2 year warranty.

Fan Assembly - Line Drawing

150mm Centrifugal (190 Motor)

Models A B C

150mm Axial 369 110 305

150mm Ctr’fgl (190 Motor) 369 110 305

150mm Ctr’fgl (220 Motor) 369 110 305

56

SIMX EXTERNAL WALL MOUNTED FANSEXTRACT MODELS

Order CodeMotor Size (mm)

DescriptionFan Performance Watts @

230VAmps

Static Pressure (Pa)

Sound Level (dB(A) @ 3m)m³/hr l/s

FAN2303 150 Axial 263 73 48 0.29 80 48

FAN2301 150Centrifugal 190 Motor (1 Speed)

392 109 65 0.28 280 60


423 118 96 0.42 380 61


High Speed 408 113 65 0.28 280 60

Medium Speed 340 94 57 0.25 250 56

Low Speed 277 77 55 0.24 200 46


High Speed 493 136 96 0.42 380 61

Medium Speed 408 113 69 0.34 340 56

Low Speed 340 94 60 0.31 280 50


FAN2303 150mm AXIAL

FAN2301 150mm CENTRIFUGAL (190 Motor)

FAN2302 150mm CENTRIFUGAL (220 Motor)

01

02

03

FAN2316 150mm 3 SPEED CENTRIFUGAL (190 Motor)

FAN2317 150mm 3 SPEED CENTRIFUGAL (220 Motor)

01

02

0

50

100

150

200

250

300

350

400

50 1000 150

Airflow (L/s)

Pre

ssur

e (P

a) 02

0

50

100

150

200

250

300

350

400

50 1000 150

Airflow (L/s)

Pre

ssur

e (P

a)

01

02

03

01


Connection

1. Electrical connection can be made inside or outside the roof space.* NOTE: All fan flow rates quoted are motor performance in free air.

THRU ROOF FAN SYSTEM MODELS

WITH FLASHING & HDPE TUBE


150mm Ctr’fgl Extract 153 l/s, 550m3hr FAN0529

150mm Ctr’fgl 3-spd Extract 153 l/s, 550m3hr FAN1002

150mm Axial - Whisper Extract 89 l/s, 320m3/hr FAN1009

150mm Axial Extract 75 l/s, 270m3/hr FAN0531

150mm Axial - Whisper Supply 75 l/s, 270m3/hr FAN0533

Duct Size Description Fan Type Performance* Order Code

150mm Ultra Ctr’fgl 153 l/s, 550m3/hr FAN0535

150mm Hyper Hyper 75 l/s, 270m3/hr DCT0189

• High quality aluminium cowl construction, with fan incorporated, for longevity of operation.• Includes Flashing for metal based roofs, an optional lead Flashing is available for concrete

tile roofs (DCT0190) at an additional cost.• Supported by a 2 year warranty.

• High quality aluminium cowl construction, with fan incorporated, for longevity of operation.• Supported by a 2 year warranty.


150mm Ctr’fgl Extract 153 l/s, 550m3hr FAN0530

150mm Ctr’fgl 3-spd Extract 153 l/s, 550m3/hr FAN0967

150mm Axial - Whisper Extract 89 l/s, 320m3/hr FAN1060

150mm Axial Extract 75 l/s, 270m3/hr FAN0532

150mm Axial Supply 75 l/s, 270m3/hr FAN0534

150mm H/D Axial Extract 75 l/s, 270m3/hr FAN0739

150mm H/D Ctr’fgl Extract 153 l/s, 550m3/hr FAN0740

H/D = Heavy Duty cowl used in these kits.

• High quality aluminium cowl construction, with fan incorporated for longevity of operation.• Includes Flashing for metal based roofs, an optional lead Flashing is available for concrete tile

roofs (DCT0190) at an additional cost.• Supported by a 2 year warranty.

150mm Axial - Whisper

150mm Axial - Whisper

150mm Hyper Fan System

58

THRU-ROOF MOUNTED FANSTHRU ROOF FAN COWL MODELS

A

B

C

Models A B C

FAN0529 - FAN1002 275 170 -

FAN1009 275 170 -

FAN0531- FAN0533 275 170 -

FAN0530 - FAN0967 275 170 500

FAN1060 275 170 500

FAN0532 - FAN0534 275 170 500

FAN0739 - FAN0740 275 170 500


Dimensions - Thru Roof Fans

FAN1009/FAN1060

FAN0530 / FAN0555

0

50

100

150

200

250

300

350

0 50 100 150 200

Pres

sure

(Pa)

Airflow (L/s)

FAN0529/FAN0530/FAN0740 FAN0532 / FAN0553

0

10

20

30

40

50

60

70

80

90

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (L/s)

FAN0531/FAN0532/FAN0739

0

20

40

60

80

100

120

140

160

0 50 100 150

Pres

sure

(Pa)

Airflow (L/s)

FAN1009 / FAN1060FAN0532 / FAN0553

0

10

20

30

40

50

60

70

80

90

0 20 40 60 80 100 120

Pres

sure

(Pa)

Airflow (L/s)

FAN0533/FAN0534

ModelsFAN0529FAN0530FAN0740

FAN1002FAN0967

FAN0531FAN0532FAN0739

FAN0533FAN0534

FAN1009FAN1060

Supply Voltage 220-240VAC 220-240VAC 220-240VAC 220-240VAC 220-240VAC

Fan Centrifugal Centrifugal Axial Axial Axial - Whisper

Fan Performance 153 l/s, 550m3/hr 153 l/s, 550m3/hr 75 l/s, 270m3/hr 75 l/s, 270m3/hr 89 l/s, 320m3/hr

Fan Wattage 58W 58W 44W 44W 46W

Maximum Pressure 320 Pa 320 Pa 80 Pa 130 Pa 130 Pa

Fan Speed 2500 RPM 2500 RPM 2850 RPM 2850 RPM 2750 RPM

Sound Level @ 1m 62 dB(A) 62 dB(A) 55 dB(A) 55 dB(A) 38 dB(A)

Operating Temp -25 - +50°C -25 - +50°C -20 - +80°C -20 - +80°C -20 - +80°C

IP Rating IPX4 IPX4 IPX2 IPX2 IPX2



• Kit comes complete with a ASA plastic cowl construction, with or without fan incorporated, mounting tubes, aquaseal roof flashing & power lead flashing.

• The orientation of the fan section can be reversed to facilitate extract or supply.• Supported by a 2 year warranty.

• High quality ASA plastic cowl construction, with fan incorporated, for longevity of operation.• The orientation of the fan section can be reversed to facilitate extract or supply.• Supported by a 2 year warranty.

COMMERCIAL THRU ROOF FAN KITS

Duct Size Description Fan Type Performance Order Code

250mm Commercial Cowl - - DCT2238

250mm Commercial Fan Cowl Ctr’fgl 178 l/s, 640 m3/hr FAN2120

250mmCommercial Fan Cowl - High Performance

Ctr’fgl 265 l/s, 954 m3/hr FAN2121

250mm Filter Ring - - DCT2254

250mm Insect Mesh - - DCT2253


250mm Commercial Kit - - DCT2241

250mm Commercial Fan Kit Ctr’fgl 178 l/s, 640 m3/hr FAN2122

250mmCommercial Fan Kit - High Performance




250 mm Hyper Fan System

250mm Commercial Fan Kit

THRU-ROOF MOUNTED FANSCOMMERCIAL THRU ROOF FAN

60


Models FAN2120/FAN2122 FAN2121/FAN2123

Supply Voltage 220-240VAC 220-240VAC

Fan Centrifugal Centrifugal

Fan Performance 178 l/s, 640 m3/hr 265 l/s, 954 m3/hr

Fan Wattage 75W 135W



Sound Level @ 1m 72 dB(A) 70 dB(A)

Operating Temp -25 - +40° -25 - +60°

Models A B C

250mm 400 400 248

B

C

A

Dimensions - Thru Roof

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

350

300

250

200

150

100

50

0

0 25 50 75 100 125 150 175 200

250mm - 220 motor

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

700

600

500

400

300

200

100

0

0 50 100 150 200 250 300 350 400

250mm - 225 Motor

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

350

300

250

200

150

100

50

0

0 25 50 75 100 125 150 175 200

250mm - 220 motor

250mm - 225 Motor

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

700

600

500

400

300

200

100

0

0 50 100 150 200 250 300 350 400

Performance - FAN2120/FAN2122

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

350

300

250

200

150

100

50

0

0 25 50 75 100 125 150 175 200

250mm - 220 motor

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

700

600

500

400

300

200

100

0

0 50 100 150 200 250 300 350 400

250mm - 225 Motor

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

350

300

250

200

150

100

50

0

0 25 50 75 100 125 150 175 200

250mm - 220 motor

250mm - 225 Motor

Sta

tic

Pre

ssu

re (

Pa)

Airflow l/s

700

600

500

400

300

200

100

0

0 50 100 150 200 250 300 350 400

Performance - FAN2121/FAN2123

COWL ON Test ConditionsNoise Rating

dB(A)125 250 500 1000 2000 4000 8000

SupplyInlet + CR 56 65.7 67.5 69.0 62.9 60.1 51.9 43.2

Discharge 55 61.1 62.0 67.8 62.4 61.8 60.7 43.9

ExtractInlet 54 62.4 62.3 67.1 61.9 60.6 58.1 48.5

Discharge + CR 54 67.2 68.5 66.1 61.4 60.9 51.2 42.3

COWL ON Test Conditions Noise Rating 125 250 500 1000 2000 4000 8000

SupplyInlet + CR 61 73.3 76.5 74.7 70.8 65.5 60.2 51.1

Discharge 60 68.9 71.5 72.4 69.9 67.9 65.5 56.1

ExtractInlet 58 69.9 72.8 69.5 68.3 65.6 62.7 54.6

Discharge + CR 60 76.2 78.1 71.7 69.5 66.8 59.0 50.2

ACOUSTIC PERFORMANCE - FAN2121/FAN2123

ACOUSTIC PERFORMANCE - FAN2120/FAN2122 Please note: CR Represents - Casing Radiation




120mm Frame Fan Standard 38 l/s, 138m³/hr FAN0397

150mm Frame Fan Standard 89 l/s, 320m³/hr FAN1043


120mm Finger Guard for FAN0397 - Metal FAN0412

120mm Filter Guard for FAN0397 FAN0413

150mm Finger Guard for FAN1043 FAN0841

ACCESSORIES

• This frame fan is designed for use in computer rooms or applications where the introduction of cool air is required for small enclosed spaces.

• The ball bearing motor prolongs the life of the motor.• Supported by a 2 year warranty.

Frame Fan 125mm

Models Frame Fan 125 Frame Fan 150

Power 220 - 240V 220 - 240V


Fan Wattage 15W 38W

Maximum Pressure 62Pa 135Pa




IP Rating IPX4 IPX2

Models A B C D

Frame Fan 125 120 120 105 40

Frame Fan 150 172 150 160 51

B

D A

C

Dimensions - Frame Fan

0 50 100 150 200

Performance - 125mm Frame Fan

72 144 180 216 252 288 324 36010836

70 90

Performance - 150mm Frame Fan

DIMENSION INFORMATION (MM)TECHNICAL SPECIFICATION

Frame Fan Accessories

62

SPECIALISED FANSFRAME FAN MODEL

Switching Options

1. Standard - operates from remote switch (not supplied).NOTE: All fan flow rates quoted are free air delivery.

Model No. Description Order Code

Time Air 7 Minute Fixed Timer (suits fans 20W-200W) FAN0372

• A fixed fan timer that will automatically run the fan for approximately 7 minutes when fan is switched on for up to 5 mins.

• Fan runs on for approx 12 minutes when switched on for over 5 mins


Fully Adjustable Run-On Fan Timer (suits fans 20W-350W) FAN2444

• Timing Switch 1 Sec to 90 Mins.• Adjustable Run On Timer & Start Delay.• Includes resistor for fans under 50W

Time Air - Fixed Fan Timer

Electronic Transformer

ELECTRONIC TRANSFORMERS


ACTO TE0060 Electronic Transformer 12VAC 50kHz FAN2101

• This transformer must only be used with 12V lighting installations.• Supports lamp wattages from 20W - 60W.• Overload & short circuit protection with self resetting.• Over temperature cut off.• Dimmable with trailing and leading edge dimmers.


SELV Isolating Transformer 12VAC FAN0436

• SELV isolating transformer is required for all low voltage fan installations.• Can be used with low voltage 12V lighting.• Supports lamp wattages from 20W - 50W.• An iron core transformer.• Thermally stable and shatter-proof plastic casings.• Overload & short circuit protection with self resetting.• Over temperature cut off.• Dimmable with trailing and leading edge dimmers.

SELV Isolating Transformer 12VAC

ISOLATING TRANSFORMERS

Fully Adjustable Run-On Fan Timer


FAN TIMERS

HUMIDISTAT CONTROLLER


UT-H1 Humidistat Controller FAN6085

• Designed to maintain the relative humidity (RH) ina room by controlling a ventilation device

• Dry and Damp Conditions setting.• Switching Capacity 15 - 200W

Humidistat Controller

Model No. Description Switching Method Order Code

1348 For XF/XP/WF 230/300 Fans* 2 Spd + Reverse FAN0155

1349 For XF/XP/WF 230/300 Fans* Adjust + Reverse FAN0156

1350 For any XF/XP/WF 230/300 Fans Adjustable FAN0157

PDL625F General Purpose up to 500W On-Off + Adjust FAN2104

FAN MOUNTING BRACKETS

• These adjustable fan mounting brackets, designed for use with the centrifugal fans.• Supplied in pairs.


100-200mm Fan Mounting Bracket for 100 - 200mm FAN0015

250-315mm Fan Mounting Bracket for 250 - 315mm FAN0016

• A range of speed controllers with variable or 2 speed and reversible options.• Models 1348 - 1350: Electrical load must be between 20 and 200 watts.• FAN0154 - Single pattress mounting block for FAN0155/0156/0157.

*Not suitable for manual pull cord model fans.


UT-T1 Touch Screen Automated Thermostat FAN5555

UT-M1 Mechanical Thermostat FAN5856

SPEED CONTROLLERS

FAN2104 General Purpose

100-200mm Fan Mounting Bracket

Mechanical Thermostat

Automated Thermostat• High quality, easy to use heat transfer thermostats.• Electronic temperature sensor.• FAN5555 is included in HeatTrans systems.

64

THERMOSTATS

Ducting Label Guide 66

Unilok FR1 - Flexible Ducting 67

Unilok FR1 - Acoustic Ducting 68

Unilok FR1 - Quadroflex Ducting 69

V-Flex - Flexible Ducting 70

Comflex Premium - Flexible Ducting 71

Comflex (Aluduct) - Flexible Ducting 72

Semiduct - Semi Rigid Ducting 73

Manrose PVC - Flexible Ducting 73

Reducers 74

Duct Joiners/Spigots 74

Inline Backdraught Shutters 75

‘Y’ Branch 75

Branch Take Off 76

Double Branch Take Off 77

Accessories - Duct Straps and Duct Tape 78

Manrose Solid Tube 79

Manrose Low Profile Ducting 80

Smartduct™ Ducting 83

Smartduct™ Ducting - Accessories 84

Duct Silencers 85

Opposed Blade Dampers 86

Motorised Directional 87

In-Line Filters 88

SW-2T Swirl Diffusers 89

CD2000 One Piece 90

One Piece Plaque Diffusers 91

One Piece 4-Way 94

Unijet Ceiling Diffusers 96

Univent Ceiling Diffusers 96

Ceiling Diffusers 97

Eggcrate Round Diffusers 97

Manrose Designer Ceiling Diffusers 98

Manrose Flat Ceiling Diffusers 98

Ceiling Diffusers 99

Manrose Designer Wall/Ceiling Grilles 100

Manrose Wall/Ceiling Grilles 101

Manrose Designer Wall Grilles 103

Manrose Wall Grilles 103

Manrose Designer Weatherproof Cowls 104

Manrose Weatherproof Cowls 104

TABLE OF CONTENTSDUCTING & GRILLES

Manrose Designer Weatherproof Domes 105

Tenmat Fire Rated Ceiling Valves 105

Double Deflection 106

Slot Diffusers 108

Eggcrate Return Grilles - Fixed Core 110

Eggcrate Return Grilles - With Filter 111

Eggcrate Return Grilles - Face Only 112

Ceiling Mounted Grilles 113

Uni Louvre Return Grilles 113

Cushion Boxes 114

Neck Adaptors 115

Trox Jet Nozzles - DUK 117

Trox Jet Nozzles - TJN 117

Trox Swirl Diffusers - VDW 117

Trox Swirl Diffusers - FD 118

Trox Swirl Diffusers - AIRNAMIC 118

Trox Swirl Diffusers - VDL 118

Trox Volume Flow Limiters - VFL 118

Weatherproof Louvre Grilles 119

Floor Registers - Side Flow Poly 120

Floor Registers - Side Flow Metal 120

Floor Registers - Front Flow Poly 121

Floor Boots 122

Louvre Return Air Grilles 123

Door Relief Air Grilles 123

Manrose Wall/Ceiling Plate Grilles 124

Manrose Door Grilles 124

Roof Cowls 125

General Purpose Cowls - Low Profile 125

Roof Cowl Kits 126

Thru Roof Mounted Fans 127

Manrose Rangehood Ducting Kits 128

Manrose Dryer Ducting Kits 129

Manrose Ducting Kits 129

66

General Information

To avoid confusion in the our range of flexible duct sizes and types, we have colour coded labels for each size. The different colours denote the various sizes.

Labels include:

Type of duct core, insulation type, length of duct and type of sleeve (where applicable).

E.g. ‘V-Flex RO.6 6m’ = V-Flex with thermal resistance of RO.6 and is 6m long.

DUCTING LABEL GUIDECOLOUR CODE SYSTEM

Pink 100mm

Dark Green 125mm

Black 150mm

Yellow 200mm

Blue 250mm

White 300mm

Red 350mm

Grey 400mm

Orange 450mm

Brown 500mm

Dark Pink 550mm

Light Green 600mm

NUDEINSULATEDFR1 R0.6

INSULATED FR1 R1.0

INSULATEDR1.5

Diameter (mm)

Length (m)

Order Code Order Code Order Code Order Code

100 36

DCT1133DCT1198

DCT1144DCT1202

12536

DCT1134DCT1143

DCT1469DCT1204

15036

DCT0561DCT0562

DCT0583DCT0584

DCT0817DCT0818

DCT3038

20036

DCT0563DCT0564

DCT0585DCT0586

DCT0819DCT0820

DCT3039

25036

DCT0565DCT0566

DCT0587DCT0588

DCT0821DCT0822

DCT3040

30036

DCT0567DCT0568

DCT0589DCT0590

DCT0823DCT0824

DCT3041

35036

DCT0569DCT0570

DCT0591DCT0592

DCT0825DCT0826

DCT3042

40036

DCT0571DCT0572

DCT0593DCT0594

DCT0827DCT0828

DCT3043

45036

DCT0573DCT0574

DCT0595DCT0596

DCT0829

50036

DCT0575DCT0576

DCT0597 DCT0830

550 3 DCT0577 DCT0599

600 3 DCT0578 DCT0600

UNILOK FR1 is a flexible duct manufactured “tough” for consumer & installer peace of mind. Unlike other types of flexible duct, UNILOK FR1 has an outer steel rib that ensures the products integrity and correct diameter, even in the tightest bends.

Due to its steel rib, it is not prone to glue failure or fatigue (sagging or ovalisation) from vibration with age like plastic ribbed or non-ribbed glued duct.

• Fully complies to AS4254 (2012) & AS1530 Pt3 and New Zealand Building Code.• Material Group Number of 1 or 1S as per NZBC.• DUCT CORE: A UV resilient fire retardant 100μm black low density polyethylene material

mechanically locked into an outer metal helix with a copper coated spring steel wire.• DUCT SLEEVE: Fire retardant 75μm black low density polyethylene and UV stabilised.• DUCT INSULATION: R0.6: Polyester R0.6.• DUCT INSULATION: R1.0: Polyester R1.0.• TEMPERATURE RANGE: Maximum: +80˚C, Minimum: -10˚C.• COLOUR: Black.

Insulated R1.0 (70mm)

Nude


UNILOK FR1FLEXIBLE DUCTING


Acoustic Insulated R0.6 (40mm)


UNILOK FR1 Acoustic Ducting is a flexible duct manufactured “tough” & “whisper quiet” for consumer & installer peace of mind. Unlike other types of flexible duct, UNILOK FR1 has an outer steel rib that ensures the products integrity, and correct diameter, even in the tightest bends.

Due to its steel rib, it is not prone to glue failure or fatigue (sagging or ovalisation) from vibration with age like plastic ribbed or non-ribbed glued duct.

INSULATED R0.6 INSULATED R1.0 INSULATED R1.5

Diameter (mm)

Length (m)

Order Code Order Code Order Code

100 36

DCT1216 DCT1268

12536

DCT1164DCT1224

DCT1176

15036

DCT0633DCT0634

DCT0833DCT0834

DCT3032DCT2600

20036

DCT0635DCT0636

DCT0835DCT0836

DCT3033DCT2601

25036

DCT0637DCT0638

DCT0837DCT0838

DCT3034

30036

DCT0639DCT0640

DCT0839DCT0840

DCT3035

35036

DCT0641DCT0642

DCT0841DCT0842

DCT3036

40036

DCT0643DCT0644

DCT0843DCT0844

DCT3037

450 3 DCT0645 DCT0845

500 3 DCT0647 DCT0846

550 3 DCT0649

600 3 DCT0650

• Fully complies to AS4254 (2012) & AS1530 Pt3 and New Zealand Building Code.• Material Group Number of 1 or 1S as per NZBC.• Designed for low noise air transfer.• Fully flexible same mechanical construction as standard Unilok ducting.• DUCT CORE: A UV resilient fire retardant 100μm black low density polyethylene perforated

material mechanically locked into an outer metal helix with a copper coated spring steel wire.• DUCT SLEEVE: Fire retardant 75μm black low density polyethylene and UV stabilised.• DUCT INSULATION: R0.6: Polyester R0.6.• DUCT INSULATION: R1.0: Polyester R1.0.• TEMPERATURE RANGE: Maximum: +80˚C, Minimum: -10˚C.• Colour: Black.

Insertion Loss, dB Octive Band Centre Frequency: Nominal 3m Length

Sample 125 250 500 1000 2000 4000 8000

150mm UNILOK FR1 R0.6 AI 35.5 39.2 36.0 30.3 29.8 31.5 22.5

300mm UNILOK FR1 R0.6 AI 33.3 35.9 27.3 31.0 28.1 17.0 12.2

400mm UNILOK FR1 R0.6 AI 36.1 30.0 20.6 27.2 26.0 12.7 10.5

UNILOK FR1ACOUSTIC DUCTING

68

• Special Purpose Ovalised Ducting.• Fully complies to AS4254 (2012) & AS1530 Pt3 and New Zealand Building Code.• Material Group Number of 1 or 1S as per NZBC.• Fully flexible same mechanical construction as standard UNILOK ducting.• DUCT CORE: A UV resilient fire retardant 100μm black low density polyethylene

material mechanically locked into an outer metal helix with a copper coated spring steel wire. Acoustic duct’s polyethylene material is perforated.

• DUCT SLEEVE: Fire retardant 75μm black low density polyethylene and UV stabilised.• DUCT INSULATION: R0.6: Polyester R0.6 nominal 250 g/m² 40mm thick.• TEMPERATURE RANGE: Maximum: +80˚C, Minimum: -10˚C.• Acoustic Duct is designed for low air noise transfer.• COLOUR: Black.

NUDEINSULATED FR1 R0.6

*ACOUSTIC FR1 R0.6

Diameter (mm)

Length (m)


20036

DCT1276DCT1282

DCT1300DCT1306

DCT1312DCT1318

25036

DCT1277DCT1283

DCT1301DCT1307

DCT1313DCT1319

30036

DCT1278DCT1284

DCT1302DCT1308

DCT1314DCT1320

35036

DCT1279DCT1285

DCT1303DCT1309

DCT1315DCT1321

40036

DCT1280DCT1286

DCT1304DCT1310

DCT1316DCT1322

45036

DCT1281DCT1287

DCT1305DCT1311

DCT1317DCT1323

QUADROFLEX has been specifically designed to fit into false ceilings, between floors and low ground clearance applications.

UNILOK FR1QUADROFLEX DUCTING

Nude



Equivalent Round Duct Size (mm)

Width (mm) Height (mm)

200 260 140

250 325 160

300 380 200

350 435 240

400 470 310

450 555 320

WIDTH

HEIGHT

Add approximately 80-140mm to these sizes to allow for insulation.

TECHNICAL DATA


• Fully complies to AS4254 (2012).• Material Group Number of 1 or 1S as per NZBC.• DUCT CORE: Reinforced multiple layered metallised PET encapsulating copper coated

spring steel wire helix. Bonded by fire retardant resin.• DUCT INSULATION R0.6: Polyester R0.6 nominal 250 g/m² 40mm thick.• DUCT INSULATION R1.0: Polyester R1.0 nominal 450 g/m² 70mm thick.• DUCT SLEEVE: Fire retardant 75μm black low density polyethylene and UV stabilised.• TEMPERATURE RANGE: Maximum: +80˚C, Minimum: -10˚C.• COLOUR: Silver with black sleeve.

NUDE INSULATED R0.6 INSULATED R1.0

Diameter (mm)

Length (m)


100 36

DCT1051DCT1050

125 3 DCT3805

15036

DCT0662DCT0663

DCT0601DCT0602

DCT0849DCT0850

20036

DCT0664DCT0665

DCT0603DCT0604

DCT0851DCT0852

25036

DCT0666DCT0667

DCT0605DCT0606

DCT0853DCT0854

30036

DCT0668DCT0669

DCT0607DCT0608

DCT0855DCT0856

35036

DCT0670DCT0671

DCT0609DCT0610

DCT0857DCT0858

40036

DCT0672DCT0673

DCT0611DCT0612

DCT0859DCT0860

45036

DCT0674DCT0676

DCT0613DCT1107

DCT0861

50036

DCT0677DCT0678

DCT0615 DCT0862

550 3 DCT0679 DCT0617

600 3 DCT0680 DCT0618

Nude



V-FLEXFLEXIBLE DUCTING

70

1. No glued/adhesive duct should be installed in a compressed or ovalised state for fear of long term failure.

• Complies to AS1530 PT3 and relevant clauses of the NZ building code.• Material Group Number of 1 or 1S as per NZBC.• DUCT CORE: Polyester film core with aluminium foil laminated onto both sides. • This composite film is then permanently bonded onto a corrosion resistant coated, spring steel wire helix.• DUCT SLEEVE: Fire retardant 75μm black low density polyethylene and UV stabilised.• DUCT INSULATION: Polyester R0.6 nominal.• TEMPERATURE RANGE: Nude Core - Maximum: +150˚C, Minimum: -30˚C.• COLOUR: Silver with black sleeve.

NUDE INSULATED R.06

Diameter (mm)

Length (m)

Order Code Order Code

100 36

DCT0215DCT0104

DCT0452

12536

DCT0216DCT0160

15036

DCT0217DCT0107

DCT0427DCT0428

20036

DCT0218DCT0109

DCT0429DCT0430

25036

DCT0219DCT0421

DCT0431DCT0432

30036

DCT0111DCT0422

DCT0433DCT0434

35036

DCT0112DCT0423

DCT0435DCT0436

40036

DCT0113DCT0424

DCT0437DCT0438


Nude

COMFLEX PREMIUMFLEXIBLE DUCTING

Note


1. All 1 metre lengths are packed in bags with header cards, 3 metre aluduct duct is supplied boxed and all other items are supplied in colour coded bags, see page 66 for colour coding.

2. No glued/adhesive duct should be installed in a compressed or ovalised state for fear of long term failure.

3. Products with the “order code” shown are generally ex. stock lines - other products are available to order.

4. Should you have an ongoing requirement for an item that is not a standard stock line - PLEASE discuss with us and we will review stocking the item for you.

MANROSEALUDUCT

NUDE INSULATED R0.6

Diameter (mm)

Length (m)

Pack Order Code Order Code Order Code

100136

Header CardedBoxed

DCT0357DCT0328 DCT0367

DCT0409

125136

Header CardedBoxed


DCT0410

150136

Header CardedBoxed


DCT0411DCT0088DCT0399

20036

Boxed DCT0331 DCT0377DCT0412

DCT0089DCT0343

25036

Boxed DCT0332 DCT0370DCT0413

DCT0400DCT0344

30036

DCT0380DCT0414

DCT0401DCT0402

35036

DCT0415DCT0416

DCT0403DCT0404

40036

DCT0417DCT0418

DCT0405DCT0406

• DUCT CORE: Aluminium foil laminated onto polyester film.• DUCT SLEEVE: Fire retardant 75μm black low density polyethylene and UV stabilised.• DUCT INSULATION: Polyester R0.6.• TEMPERATURE RANGE: Maximum: +80˚C, Minimum: -10˚C.• COLOUR: Silver with black sleeve.

Nude

Insulated

COMFLEX (ALUDUCT) FLEXIBLE DUCTING

72

NUDE INSULATED R0.6*

Diameter (mm) Length (m) Pack Order Code Order Code

1001.53

BoxedLoose

DCT0333DCT0114

1251.53

BoxedLoose

DCT0334DCT0115

1501.53

BoxedLoose


200 3 Loose DCT0117 DCT2589





SEMIDUCT is also known as semi-rigid aluminium ducting is a lightweight, flexible but strong corrugated aluminium duct. It is spiral wound with a unique interlocked and knotted continuous seam. It is self supporting over longer lengths and generally only needs fittings or mechanics at each end for support.

SEMIDUCT SEMI RIGID DUCTING

Semiduct Semi Rigid Ducting

• Fully complies to AS1530 Building code.• DUCT CORE: Spiral wire reinforced PVC film construction.• Non-collapsing/non-rotting.• Vapour-proof.• Fire retardant.• TEMPERATURE RANGE: Maximum: +50˚C : Minimum: 6˚C.• COLOUR: White PVC.

Diameter (mm) Length (m) Pack Order Code

10013

Header CardedBoxed

DCT0936DCT0336

12514

Header CardedBoxed

DCT0937DCT0337

15015

Header CardedBoxed

DCT0938DCT0338

PVC Flexible Duct is a product that is extremely versatile in the ventilation industry. It doesn’t rot, is non-collapsing, is fire resistant, has an operating temperature of +6° to +50° and is available in a range of sizes from 100mm to 150mm.

MANROSE PVCFLEXIBLE DUCTING

150mm PVC Flexible Ducting

• Fully complies to the New Zealand Building Code.• DUCT CORE: Pure aluminium spiral wound with a unique interlocked and knurled continuous seam.• Holds shape, self supporting.• TEMPERATURE RANGE: Maximum: +250°C, Minimum: -30°C.• COLOUR: Silver.

Sold as compressed packaged form. *Sold in kitset form - some assembly required.


Note

1. Products with the “order code” shown are generally ex. stock lines - other products are available to order.

2. Nude combination fittings will be supplied in component form. We do NOT assemble.

3. Insulated versions may not be ex-stock but will generally be available within 2-3 days of ordering.

4. Should you have an ongoing requirement for an item that is not a standard stock line – PLEASE discuss with us and we will review stocking the item for you.

PVC Plastic

Poly/Insulated/Metal

REDUCERS

• Poly - High Density Polyethylene (HDPE).• Heavy duty, robust, positive lock duct tabs.

PVC POLY INSULATED METAL

Duct Size (mm) Order Code Order Code Order Code Order Code

125-100 DCT2067

150-100 DCT2122

150-125 DCT2066

200-125 DCT0084

200-150 DCT0486 DCT0901

225-150 DCT0078

250-150 DCT0162

250-200 DCT0487 DCT0902

300-250 DCT0488 DCT0903

315-300 DCT2996 (Long)

350-300 DCT0489 DCT0904

400-350 DCT0490 DCT0905

450-300 DCT0916

500-450 DCT4237

PVC METAL LONG METAL SHORTMETAL PLATE SPIGOTS


100 DCT0159

125 DCT0037

150 DCT3528 DCT0723 DCT0059 DCT0935

200 DCT0724 DCT0071 DCT0939

250 DCT0725 DCT0339 DCT0940

300 DCT0726

350 DCT0770

400 DCT0771

450 DCT0772

500 DCT1157

PVC PlasticMetal Long

Metal Short Metal Plate Spigots

DUCT JOINERS/SPIGOTS

• Heavy duty, robust, positive lock duct tabs.

74

• Manufactured from HDPE.• UV stabilised.• Heavy duty, robust.• Smooth internal lines.• No sharp edges.• Positive lock duct tabs.• Insulation meets AS1530 part 3.• Insulation material LDPE, thickness 5mm.

PVC POLY INSULATED METAL


100-100-100 DCT2182

125-125-125 DCT2183

150-100-100 DCT0079

150-125-125 DCT0707

150-150-150 DCT2184 DCT1233

200-150-150 DCT0379 DCT0865

200-200-200 DCT0376 DCT0955

250-200-200 DCT0471 DCT0866

300-250-250 DCT0717 DCT0868

300-300-200 DCT4190

300-300-300 DCT0494 DCT0869

350-250-250 DCT1433 DCT1034

350-300-300 DCT0718 DCT0870

350-350-350 DCT0776 DCT0871

400-300-200 DCT4191

400-300-300 DCT0777 DCT0872

400-350-300 DCT0813 DCT0873

400-350-350 DCT0778 DCT0874

400-400-200 DCT4192

400-400-250 DCT4193

400-400-350 DCT1116 DCT1128

‘Y’ BRANCH

100-100-100 ‘Y’ Branch

Note



1. Combinations of sizes which are not ex. stock can be made up using a suitable body and the relevant reducers and fitting joiners poly.


Coded products shown are generally ex-stock lines, however, other products are available to order. See our website

INLINE BACKDRAUGHT SHUTTERS

PVC METAL

Size (mm) Order Code Order Code

100 FAN0213

125 DCT0036

150 DCT0511 DCT2692

200 DCT2092

315 DCT2337


• Manufactured from HDPE.• UV stabilised.• Heavy duty, robust.• Smooth internal lines. • No sharp edges.• Positive lock duct tabs.• Insulation meets AS1530 part 3.• Insulation material LDPE, thickness 5mm.

POLY INSULATED METAL

Duct Size (mm) Order Code Order Code Order Code

100-100-100 DCT1439

125-125-125 DCT1501

150-150-100 DCT0080

150-150-150 DCT0091 DCT0875

200-150-150 DCT0719 DCT0876

200-200-150 DCT0460 DCT0877

200-200-200 DCT0461 DCT0878

250-150-150 DCT1063 DCT0967

250-200-150 DCT1064

250-200-200 DCT0462 DCT0879

250-250-150 DCT0463 DCT0880

250-250-200 DCT0720 DCT0881

250-250-250 DCT0464 DCT0882

300-200-150

300-200-200 DCT1129 DCT1130

300-250-150

300-250-200 DCT0721 DCT0883

300-250-250 DCT0730 DCT0884

300-300-150

300-300-200 DCT0978 DCT1094

300-300-250 DCT0979 DCT1015

300-300-300 DCT0491 DCT0885

350-250-150

350-250-200

350-250-250 DCT0465 DCT0886

350-300-150

350-300-200 DCT0915 DCT0945

350-300-250

350-300-300 DCT0493 DCT0887

350-350-150

350-350-200

350-350-250

350-350-300

BRANCH TAKE OFF (B.T.O)

200-200-200 Branch Take Off

Note

1. Products with the “order code” shown are generally ex. stock lines -other products are available to order.

76

• Manufactured from HDPE.• UV stabilised.• Heavy duty, robust.• Smooth internal lines.• No sharp edges.• Positive lock duct tabs.• Insulation meets AS1530 part 3.• Insulation material LDPE, thickness 5mm.

POLY INSULATED

Duct Size (mm) Order Code Order Code

200-150-150-150 DCT0090 DCT0889

250-150-150-150 DCT0467 DCT0890

250-200-150-150 DCT0480 DCT0891

250-200-200-150

250-200-200-200 DCT1422 DCT0973

250-250-150-150

250-250-200-150

300-200-200-150

300-200-200-200 DCT0481 DCT0893

300-250-150-150

300-250-200-150

300-250-200-200 DCT0482 DCT0894

300-250-250-150

300-250-250-200

300-250-250-250 DCT0722 DCT0895

300-300-150-150

300-300-200-150

300-300-200-200 DCT0483 DCT0896

300-300-250-200

300-300-300-300

350-250-150-150

350-250-200-150

350-250-200-200 DCT0470 DCT0897

350-250-250-150

350-250-250-200

350-250-250-250 DCT0469 DCT0898

350-300-150-150

350-300-200-150

350-300-200-200 DCT2060 DCT2061

350-300-250-150

350-300-250-200

350-300-250-250 DCT0484 DCT0899

350-300-300-150

350-300-300-200

POLY INSULATED

Duct Size (mm) Order Code Order Code

350-300-300-250

350-300-300-300

350-350-150-150

350-350-200-150

350-350-200-200 DCT0485 DCT0900

350-350-250-200

350-350-250-250

350-350-300-150

350-350-350-200

350-350-350-300

350-350-350-350

200-200-200 Double Branch Take Off

DOUBLE BRANCH TAKE OFF (D.B.T.O)

1. Products with the “order code” shown are generally ex. stock lines -other products are available to order.


Duct Size (mm) Description Order Code

100mm Cable Ties FAN0274



12mm x 3m Hanging Strap + Clips DCT2299

25mm x 50m Hanging Strap DCT0808

48mm x 5m Duct Tape Grey (Box of 200) DCT0173

48mm x 30m Duct Tape Grey (PVC Box of 24) DCT0807

48mm x 30m Duct Tape Black (Box of 24) DCT4142

48mm x 108m Duct Tape Silver UL181 DCT3232

75mm x 45m Aluminimum Tape (P3) DCT3020

Ducting Straps & Duct Tape

Duct Tape Silver UL181

78

ACCESSORIESDUCT STRAPS AND DUCT TAPE

Diameter (mm) Length (m) Finish Order Code

100 0.9 Galvanised DCT0151

100 0.9 White DCT0145


125 0.9 White DCT0146



150 0.9 White DCT0147


Diameter (mm) Length (m) Finish Order Code

100 1 White DCT1424

125 1 White DCT1425

150 1 White DCT1426

150 2.5 White DCT3527

150 5 White DCT3530

150 6 White DCT4196

GALVANISED STEEL TUBES

PVC TUBES

MANROSE SOLID TUBE

White Galvanised Tube

Galvanised Tube

PVC Tube

Size (mm) Description Order Code

100 PVC Round 90° Bend DCT3770




PVC BENDS


VERTICAL 90° BENDS

Dimension (mm) Order Code

110 x 54 DCT0126 (F)

204 x 60 DCT0525 (F)

220 x 90 DCT1447 (F)

300 x 25 DCT2099 (F)

LOW PROFILE CONNECTORS


110 x 54 DCT0014 (F)

204 x 60 DCT0520 (F)

220 x 90 DCT1442 (F)

300 x 25 DCT1459 (F)

HORIZONTAL 90° BENDS


110 x 54 DCT0125 (F)

204 x 60 DCT0524 (F)

220 x 90 DCT1448 (F)

300 x 25 DCT2097 (F)

HORIZONTAL T-PIECE CONNECTORS


110 x 54 DCT1479 (F)

204 x 60 DCT1114 (F)

220 x 90 DCT3126 (F)


220 x 90 DCT2701 (F)

300 x 25 DCT2098 (F)

HORIZONTAL 45° BEND


220 x 90 DCT2700 (F)

300 x 25 DCT1455 (F)

VERTICAL 45° BEND

Dimension (mm)Equivalent Size (mm)

Length (m) Order Code

110 x 54 100 1.5 DCT0013 (M)

204 x 60 125 1.5 DCT0519 (M)

220 x 90 150 1.5 DCT1443 (M)

300 x 25 100 1.5 DCT1460 (M)

MANROSE LOW PROFILE DUCTING-FLAT CHANNEL

Low profile ducting enables it to be concealed when installed along the top of wall units. It can also be fitted in ceiling voids and cavity walls, providing versatility whilst remaining unobtrusive. All Manrose system parts and channels are made from flame-retardant material.

Four Low Profile System Sizes

110mm x 54mm:

Suitable for applications requiring low extraction rates, such as ventilation of domestic bathrooms and toilets.

With a 5940mm2 cross-section it provides efficient ducting for short, straight runs connecting to a 100mm round spigot.

204mm x 60mm:

Suitable for ducting of kitchen cooker hoods with 100, 125 or 150mm round exhaust spigots. The flat channel cross section of 12240mm2 increases efficiency.

High Performance 220mm x 90mm:

Suitable for applications requiring high performance extraction or supply. The flat channel cross section of 19800mm2 makes it highly efficient and higher extraction rates are achieved.

Flat Ducting 300mm x 25mm:

Suitable for applications where space is very limited.

204mm x 60mm Low Profile Ducting Flat channel. Box of 6

(M) = Male (F) = Female

80

MANROSE LOW PROFILE DUCTINGFLAT CHANNEL

(m) = Male (f) = Female

ELBOW BENDS 100mm


110 x 54 DCT0124 (M)

110 x 54 DCT0015 (F)

204 x 60 DCT0521 (F)

220 x 90 DCT1444 (F)

300 x 25 DCT2095 (F)


204 x 60 DCT0523 (F)

220 x 90 DCT1441*(F)

ELBOW BENDS 150mm

*Rotating offset spigot

*Rotating offset spigot

ELBOW BENDS 125mm


204 x 60 DCT0522 (F)

220 x 90 DCT1440* (F)

300 x 25 DCT2096 (F)


204 x 60 DCT1480 (F)

HORIZONTAL BEND ADJUSTABLE

Comes complete with duct connector DCT0520.

Dimension mm) Order Code

204 x 60 DCT1414 (F)

VERTICAL AIRBRICK INSERT

Duct connection requires the following Reducer or Connector:

110 x 54: requires: DCT0136 204 x 60: requires: DCT0520


204 x 60 DCT0137 (M)

HORIZONTAL AIRBRICK INSERT

Designed to fit 204 x 60mm flat channel or airbrick.

FLAT CHANNEL REDUCERS


110 x 54:204 x 60 DCT0136 (F)

204 x 60:220 x 90 DCT1452 (F)

300 x 25:204 x 60 DCT1456 (F)(M) = Male (F) = Female

SHORT ADAPTER RECTANGULAR: ROUND


110 x 54 : 100 DCT0127 (F)

110 x 54 : 100 DCT0131 (M)

ADAPTERS RECTANGULAR: ROUND


110 x 54 : 100 DCT1482 (F)

204 x 60 : 125 DCT0526 (F)

220 x 90 : 150 DCT1446 (F)

300 x 25 : 100 DCT1461 (F)

MANROSE LOW PROFILE DUCTINGDUCT FITTINGS


DOUBLE AIRBRICK


232 x 138 DCT1450 (F)


235 x 140 DCT1453 (M)

DOUBLE AIRBRICK REDUCER

DOUBLE AIRBRICK ADAPTOR


220 x 90:232 x 138 DCT1451 (M/F)

EXTERNAL LOUVRED GRILLES

Diameter (mm) Order Code

100 DCT2200

125 DCT2201

150 DCT2202

A B

*2 clips are required to secure ducting.

FLAT CHANNEL CLIPS


110 x 54 (A) DCT0134

204 x 60 (A) DCT0527

220 x 90 (B) DCT1445*

300 x 25 (B) DCT1458*

Diameter (mm) Order Code

100 DCT2206

EXTERNAL TUBE GRILLE

Designed to fit directly into round solid tube, for systems ducted straight through an external wall.

WALL/CEILING PLATES RECTANGULAR


155 x 155 : 110 x 55 DCT0016

264 x 118 : 206 x 60 DCT0528

WALL/CEILING PLATES ROUND


155 x 155 : 104 ø DCT0148

170 x 170 : 130 ø DCT0149

200 x 200 : 160 ø DCT0150

82

MANROSE LOW PROFILE DUCTINGDUCT FITTINGS

SmartDuct is a revolutionary way to duct. It is based on unique construction and installation procedures.

Characterised by simple assembly and fast installation, both of which will ensure cost advantages over standard insulated rigid ducting. SmartDuct consists of precut panels ready to be assembled with a supplied bayonet to create a labyrinth type joint.

• Pre insulated aluminium ducting.• Cost effective.• Light weight.• Fast assembly.• Low pressure drop.• Internal bactericidal coating.• Green water blown foam.• R=0.55• Fire Rated to AS 1530.3-1999 & UL181.11-2005

SMART4 with Take Off

SMART8

Description Length (m) Order Code

150mm 1.2 DCT2400

200mm 1.2 DCT2401

250mm 1.2 DCT2402

300mm 1.2 DCT2403

400mm 1.2 DCT2404

500mm 1.2 DCT2405


150mm DIA 1.2 DCT2406

200mm DIA 1.2 DCT2407

250mm DIA 1.2 DCT2408

300mm DIA 1.2 DCT2409

350mm DIA 1.2 DCT2410

400mm DIA 1.2 DCT2411


250x150mm 1.2 DCT2711

350x150mm 1.2 DCT2712

450x150mm 1.2 DCT2713

500x250mm 1.2 DCT2714

SMART4 SQUARE

SMART4 RECTANGULAR

SMART8 OCTAGONAL

Using the 12mm pre-cut panels, assemble the straight duct by simply bending and inserting the “labyrinth” bayonet (panels and bayonets are provided together in kit form).

With a specific connector it is possible to join single pieces of duct, giving the ability to mae any length of straight duct.

To make reducers/bends, the straight duct can be easily cut and joined with the relevant connectors.

SMARTDUCT CONSTRUCTION

0201

03 04


SMARTDUCT™ DUCTING

SMARTDUCT™ DUCTINGACCESSORIES

The real secret behind the Smart and Smart8 is its simple assembly.

Starting with a length of straight duct, a total ducting system can be easily assembled, using simple bayonet and proprietary fittings - bends, reducers, off-sets, etc.

The labyrinth join system has excellent sealing properties ensuring air tight joints along the ducting edges.

SMARTDUCT SQUARE/OCTAGON

END CAPS

SMARTDUCT 45° BENDS

TAKE-OFFS

INSTALLATION TOOLS

SMART4 SMART8

Straight Joiners Straight Joiners


150 DCT2412 DCT2418

200 DCT2413 DCT2419

250 DCT2414 DCT2420

300 DCT2415 DCT2421

350 N/A DCT2422

400 DCT2416 DCT2423

500 DCT2417 N/A

SMART4 SMART8


150 DCT2424 DCT2430

200 DCT2425 DCT2431

250 DCT2426 DCT2432

300 DCT2427 DCT2433

350 N/A DCT2434

400 DCT2428 DCT2435

500 DCT2429 N/A

SMART4

Size (mm) Order Code

150 DCT2554

200 DCT2555

250 DCT2556

300 DCT2557


500 ml Glue DCT2448

Metal Join Clips DCT3461

Aluminium Tape DCT3020

SMART4 SMART8


150 DCT2436 DCT2442

200 DCT2437 DCT2443

250 DCT2438 DCT2444

300 DCT2439 DCT2445

350 N/A DCT2446

400 DCT2440 DCT2447

500 DCT2441 N/A

Use 2x 45° bends to make a 90° bend.

84

Easily-fitted silencer for circular ducts, fitted with a connection that complies with the spiral duct standard. The Duct Silencer effectively reduces noise in the duct. Two silencers can be used together in installations where noise reduction is a particularly strong requirement.

This is very effective for the most effective noise reduction, the silencer should be fitted immediately behind the fan or bend. The silencer should be used together with an insulated fan where there is a requirement for noise reduction both in the duct and in the surroundings as a whole.

• Easily fitted for circular ducts.• Effectively reduces noise in the duct.• More than one silencer can be used together in installations,

where noise reduction is a particularly strong requirement.• Other sizes available on request.

TECHNICAL DATA

Noise suppression DB (mid-frequency Hz)

LDC 63 125 250 500 1k 2k 4k 8k

100-300 2 2 6 14 21 25 20 11

100-600 4 3 11 24 36 49 34 17

100-900 5 4 15 34 50 50 48 23

100-1200 6 5 19 45 50 50 50 29

125-600 3 3 9 23 30 40 22 14

125-900 4 4 12 33 45 50 30 17

125-1200 5 5 15 43 50 50 38 21

150-600 - 3 7 20 27 31 16 11

160-600 2 3 7 19 27 29 14 11

160-900 2 4 10 28 42 43 20 15

200-600 2 3 7 16 21 23 9 8

200-900 2 4 8 24 32 34 13 10

250-600 3 2 7 13 17 16 8 6

250-900 3 4 8 20 26 23 10 8

315-600 0 2 6 11 14 9 4 5

315-900 1 3 7 16 22 12 6 7

355-900 - 3 6 13 18 10 6 7

400-900 1 3 5 10 13 7 5 6

DUCT SILENCERS

Ø di

Ø d0

Ø di Duct Size (mm)

Length (mm)

Ø d0 Tube Order Code

100 600 200

100 900 200

125 600 225 DCT2617

125 900 225

150 600 260 DCT2090

150 900 260 DCT3112

Ø di Duct Size (mm)

Length (mm)

Ø d0 Tube Order Code

200 600 315 DCT2630

200 900 315 DCT3113

250 600 355 DCT3114

250 900 355 DCT3115

315 600 450 DCT3116

315 900 450 DCT3117

150mm x 600mm Duct Silencer


• Manufactured in high quality aluminium extrusion profiles.• Designed with nylon bearings for efficient, smooth operation.• Clips onto one piece 4-Way aluminium diffusers (see above). • Powder coated black.• Opposed blade damper design to ensure regulation of airflow.• Screw type opening mechanism.• Special sizes made to order, please state neck size, POA.

Nomimal Neck Size (mm)

Order Code

150 x 150 DCT2015

157 x 157 DCT1970

225 x 225 DCT2016

300 x 300 DCT2017

300 x 150 DCT4138

360 x 360 DCT2018

450 x 450 DCT2019

500 x 200 DCT4136

600 x 300 DCT4134

E = 75mm

DIMENSION INFORMATION

OPPOSED BLADE DAMPERS (O.B.D)

225mm x 225mm Opposed Blade Damper

86

Note

1. Products with the “order code” showing are generally ex. stock lines - other products are available to order.




• Manufactured from HDPE.• Complete with hand quadrant.• Braced for strength with 2 x 6mm steel rod rings.• Positive lock duct tabs.• Insulation meets AS 1530 part 3.

Duct Size (mm) Order Code

150 DCT0787

200 DCT0706

250 DCT0788

300 DCT2706

350

400

• Standard 240V Drive Open, Drive Close (D.O.D.C) motor attached.• Manufactured from ABS plastic.• Single damper motor & paddle control to direct airflow into or from selected branch.• Designed for both dual supply air and extract air applications.• Aesthetic smooth lines.


150 DCT1495

200 DCT1500

• Standard 240V Drive Open, Drive Close (D.O.D.C) motor attached.• Other voltages available upon request.• Manufactured from HDPE.• Braced for strength with 2 x 6mm steel rod rings.• 100% positive shut off and positive lock duct tabs.• Insulation meets AS 1530 part 3.


150 DCT1168

200 DCT1123

250 DCT1124

300 DCT1125

350 DCT1126

400 DCT1127

Note: These are insulated

Note: These are insulated

MOTORISED BARREL DAMPER

MANUAL BARREL DAMPER

150mm Motorised Directional T-Branch Damper

MOTORISED DIRECTIONALT-BRANCH DAMPER


• Other filters available, please enquire.

This high quality F7 filter captures pollens, dust and allergens from the air. Over its life the filter will, as an average, have an 80-90% arrestance on particles 0.4 microns in size and above.

The filter cassette is held in a frame of silicon impregnated cardboard which is fitted with two plastic neck adaptors to facilitate maintenance and replacement. This design also permits a range of duct sizes for the same filter cassette.

Duct Size (mm) Filter Order Code

150 G4 DCT1412

IN-LINE FILTERS

SOCK FILTER FRAME


150 G4 DCT1411

SOCK FILTER MEDIA

G4 grade sock filter is a quality filter, to filter out dust and pollens from the air. Over its life the filter will, as an average, have 90% arrestance of particles of 5 microns in size and above.

Duct Size (mm) Filter Suits Filter Size (mm) Order Code

300 x 300 F7 150/200 DCT2093

225 x 225 G4 150 DCT2221

300 x 300 G4 200 DCT2222

300 x 300 HEPA/Carbon 150/200 DCT2278

300 x 300 F7/Carbon 150/200 DCT2277

REPLACEMENT IN-LINE FILTER CARTRIDGE

F7 In-Line Filter

Replacement F7 Filter

G4 Sock Filter


150 F7 DCT2076

200 F7 DCT2075

150 G4 DCT2073

200 G4 DCT0009


150 HEPA/Carbon DCT2281

200 HEPA/Carbon DCT2282

150 F7/Carbon DCT2279

200 F7/Carbon DCT2280

IN-LINE FILTERS FOR SMART-VENT

88

The resistance curve has been constructed from numerical and empirical measurements of the pressure drop across the filter for a range of in-line duct flow rates.

430mm

300mm

300mm

150mm

F7 In-Line Filter Replacement F7 Filter

0.0001 0.001 0.01 0.1 1.0 10 100 100001000

F7 G4

Filter Classification of Common Air Contaminants (shown in micrometres)

FILTER CLASSIFICATION

EU 7 In-Line Fliter Resistance Curve

0

50

100

150

0 50 100 150 200 250

Airflow (l/s)

Pre

ssur

e D

rop

(Pa)


RESISTANCE CURVE



No. of blades = 29

Top View

Oval Inlet Nominal Inlet Diameter, ID

Top Round Inlet ID

SW-2T with Plenum Box

SW-2T series is a swirl diffuser with fixed radially arranged air control blades. This unique type of slot provides high induction “vortex” air flow, projecting horizontally from the face of diffuser. This swirling air flow produces a diffuser air distribution, with no stationary air jet resulting in excellent uniformity of temperature in air conditioned spaces.

SW-2T is suitable in area of high heat load where large quantities of cool air must be rapidly mixed with room air; areas which require high air change in a short time. The SW-2T series can also be use as a return and exhaust type device.

Materials

• Diffuser Face: 1.0mm thickness galvanized steel.• Outer Frame: 1.0mm thickness galvanized steel.Surface Finish

• White powder coated as standard.Features

• Diffuser face can be opened without using any tools.• Volume control damper is adjustable without removing ceiling panel.• Swirl air pattern provides high induction ratio.• High coanda effect reduces direct-throw of air on occupants.• Standard sizes available for T-bar ceiling on metric or imperial size.


250 SW-2T Swirl + 250mm Side Entry Box DCT2634

250 SW-2T Swirl + 250mm Top Entry Box DCT2614

300 SW-2T Swirl + 300mm Side Entry Box DCT2635

300 SW-2T Swirl + 300mm Top Entry Box DCT2613

350 SW-2T + 350mm Side Entry DCT2615

SW-2T Swirl Plate only DCT2636

SW-2T

SW-2T SWIRL DIFFUSERS

90

Blades

Frame

Diffuser Face

Perforated Sheet (optional)

Collar

Locking Mecha-nism

Outer Frame

Isometric Front View Isometric Back View

Inlet Diameter(mm)

Collar Neck Vel. (m/s) 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0

Vel. Press (Pa) 2 3 4 6 8 10 13 16 19 23

150

l/s 26 35 44 53 61 70 79 88 97 106

Tot. Press (Pa) 3 6 9 12 17 22 27 32 39 48

NR (dB(A)) - - - - - - 23 26 30 33

Throw (m)0.6 - 1.2

0.9 - 1.5 0.9 - 1.8 1.2 - 1.8 1.5 - 2.1 1.5 - 2.1 1.5 - 2.4 1.8 - 2.4 1.8 - 2.7 1.8 - 2.7

200

l/s 47 63 79 95 110 125 141 156 172 188

Tot. Press (Pa) 4 7 12 17 23 30 37 48 55 65

NR (dB(A)) - - - 21 27 31 35 38 40 41

Throw (m)0.6 - 1.2

0.9 - 1.5 0.9 - 2.1 1.2 - 2.1 1.5 - 2.4 1.5 - 2.7 1.8 - 2.7 2.1 - 3.0 2.1 - 3.0 2.1 - 3.4

250

l/s 74 99 124 149 171 196 220 245 270 294

Tot. Press (Pa) 6 11 17 29 39 49 61 76 91 108

NR (dB(A)) - - 21 28 34 36 40 42 44 46

Throw (m)0.9 - 1.8

1.2 - 2.4 1.5 - 2.7 1.8 - 3.0 2.1 - 3.4 2.4 - 3.7 2.7 - 4.0 2.7 - 4.0 3.0 - 4.3 3.0 - 4.3

300

l/s 107 143 179 215 247 282 318 353 388 424

Tot. Press (Pa) 13 23 35 51 68 90 113 141 170 214

NR (dB(A)) - 24 30 38 41 44 47 49 51 54

Throw (m)1.2 - 2.4

1.5 - 3.0 1.8 - 3.4 2.4 - 4.0 2.7 - 4.3 3.0 - 4.6 3.4 - 4.6 3.7 - 4.9 3.7 - 5.2 3.9 - 5.5

PERFORMANCE DATA

D C ID (nom) PH I OC IC PL IL AH CH

595

150 200 250 300350

150 200 235 300350

190 190 210 230250

535 513 190 580 60 100 60

TECHNICAL DATA


• Manufactured from V-Zero fire rated ABS plastic. AS/NZ 1530.3.• Resistant to scratching and fading.• Minimises problems associated with cold bridging in high humidity areas.• Spring loaded fixing clips.• Poly neck adaptors and side entry cushion boxes see page 115 • Oppose blade damper available for order.

Neck Size (mm) Order Code

225 x 225 DCT0792

300 x 300 DCT0468

360 x 360 DCT0793

435 x 435 DCT0794*

Neck Adaptor Size (mm)

Neck Vel(m/s)

1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5

225 x 225

PD (Pa) - 10 18 27 38 51 66 83 101 121 143 166

Throw (m) - 0.8 1.7 3.8 5.7 7.4 8.9 10.2 11.4 12.3 13.1 13.7

NR (dB(A)) - < 8 < 15 20 24 29 33 38 41 45 48 50

300 x 300

Flow (l/s) - 118 157 196 235 274 314 353 392 431 470 510

PD (Pa) - 10 18 27 38 51 66 83 101 121 143 166

Throw (m) - 1.7 4.4 6.9 9.1 11.0 12.6 13.9 15.0 15.8 16.4 16.9

NR (dB(A)) - < 11 < 18 23 27 31 36 40 44 47 50 53

360 x 360Flow (l/s) 126 189 252 315 378 441 504 567 630 693 756 819

PD (Pa) 5 10 18 27 38 51 66 83 101 121 143 166

Throw (m) 1.5 4.8 8.2 11.2 13.7 15.8 17.4 18.7 19.6 20.3 20.8 21.0

NR (dB(A)) 1 13 20 25 29 34 38 42 46 49 52 56

595 x 595Flow (l/s) 185 277 370 462 555 647 740 832 925 1017 1109 1202

PD (Pa) 5 10 18 27 38 51 66 83 101 121 143 166

Throw (m) 3.8 8.2 12.3 15.7 18.5 20.7 22.4 23.7 24.5 25.1 25.4 25.5

NR (dB(A)) 6 15 22 27 31 36 40 44 48 51 54 57

CD2000 One Piece - 4 Way Diffuser

• * 595 x 595mm “lay in” T-rail diffuser.

See below for actual dimensions.

CD2000 ONE PIECE 4-WAY DIFFUSER

TECHNICAL DATA

92

D

C

B

A

E

F


225 x 225 DCT2012

300 x 300 DCT2013

360 x 360 DCT2014

Side View

Neck Size (mm) A (mm) B (mm) C (mm) D (mm) E (mm) F (mm)

225 x 225 207 220 595 45 212 85

300 x 300 278 294 595 45 285 85

360 x 360 355 369 595 45 360 85


ONE PIECE PLAQUE DIFFUSERS

• One piece pressed aluminium, powder coated white.• Removable core, no joints, smooth airflow.• Poly neck adaptors and side entry cushion boxes see page 115 • 595 x 595mm “lay in” T-rail diffuser.


Front View

300 x 300 One Piece Plaque Diffuser


D

C

B

A

E

F

Side View Front View


• One Piece Diffusers.• Manufactured from aluminium sheets in one piece, no joints, smooth airflow.• Easily removable internal core assembly for ease of installation.• Negligible resistance to airflow.• Powder coated white.

Neck Size (mm) A (mm) B (mm) C (mm) D (mm) E (mm) F (mm)

150 x 150 131 144 290 45 137 85

225 x 225 207 220 365 45 212 85

300 x 300 278 294 440 45 285 85

360 x 360 355 369 515 45 360 85

450 x 450 430 444 595 45 435 85

TECHNICAL DATA


150 x 150 DCT2006

225 x 225 DCT2007

300 x 300 DCT2008

360 x 360 DCT2009

450 x 450 DCT2010*

• One piece pressed aluminium, powder coated white.• Removable core, no joints, smooth airflow.• Poly neck adaptors and side entry cushion boxes see page 115

* 595 x 595mm “lay in” T-rail diffuser.


94

300 x 300 One Piece 4-Way

ONE PIECE 4-WAY DIFFUSER



Neck Vel (m/s)

1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7

150 x 150

Flow (l/s) - 36 46 55 64 73 82 91 100 109 118 128

PD (Pa) - 13 19 27 37 47 59 72 86 102 119 136

Throw (m) - 0.8 1.2 1.4 2.9 4.4 5.6 6.6 7.6 8.5 9.4 10.2

NR (dB(A)) - 11 15 19 22 24 27 29 32 36 38 41

225 x 225

Flow (l/s) 66 88 110 132 154 176 198 221 243 265 287 309

PD (Pa) 7 13 19 27 37 47 59 72 86 102 119 136

Throw (m) 0.8 2.0 4.9 7.0 8.7 10.2 11.6 12.9 14.2 15.5 16.8 18.1

NR (dB(A)) 9 15 19 23 26 29 33 37 40 43 46 48

300 x 300

Flow (l/s) 122 162 203 244 284 325 366 406 447 487 528 569

PD (Pa) 7 13 19 27 37 47 59 72 86 102 119 136

Throw (m) 1.8 5.6 8.0 9.9 11.5 13.1 14.7 16.3 18.0 19.7 21.4 23.2

NR (dB(A)) 12 18 22 26 29 34 38 42 45 48 51 53

360 x 360

Flow (l/s) 194 259 324 389 454 518 583 648 713 778 842 907

PD (Pa) 7 13 19 27 37 47 59 72 86 102 119 136

Throw (m) 4.5 7.5 9.6 11.3 13.0 14.7 16.5 18.4 20.4 22.5 24.7 27.0

NR (dB(A)) 14 20 24 28 33 38 42 46 49 52 55 57

595 x 595

Flow (l/s) 290 387 484 581 678 774 871 968 1065 1162 1258 1355

PD (Pa) 7 13 19 27 37 47 59 72 86 102 119 136

Throw (m) 6.4 8.7 10.4 12.0 13.8 15.7 17.8 20.0 22.3 24.8 27.4 30.0

NR (dB(A)) 16 22 26 31 37 41 45 49 52 55 58 61

TECHNICAL DATA CONT.

Unijets have been designed not to just ‘dump’ air straight down like other similar diffusers.

The Unijet disperses the air over a greater area because its louvres are at different angles. This gives a more even temperature over a greater area.

UNIJET CEILING DIFFUSERS

Duct Size (mm) Colour Order Code

150 Ice White DCT2610



• Manufactured from V-Zero fire rated ABS plastic AS/NZ 1530 pt 3• Designed to push supply air into the room as shown.• Spring loaded fixing clips.• Adjustable ‘set and forget’ damper blade.• Comes with damper blade adjustment tool.• Resistant to scratching and fading.• Positive lock duct tabs.


Duct Size (mm)

Face Size (mm)

Spigot Diameter (mm)

Spigot Length (mm)

Cut-Out Size (mm)

150 220 145 70 200

200 268 195 70 250

Unijet Ceiling Diffuser

Round Ceiling Diffusers

www.uniflex.com.au

Westaflex / Uniflex Australia Pty Ltd ABN 21 005 072 873

Head Office 140 - 152 Bamfield Rd, Heidelberg West Victoria Australia 3081Postal Address P.O. Box 133 West Heidelberg Victoria 3081 Australiaphone +61 (0)3 9458-2122 fax +61 (0)3 9458-3120 email [email protected]

Branches Throughout Australia & New ZealandAustralia: Melbourne, Sydney, Penrith, Newcastle, Canberra, Dubbo, Adelaide, Perth, Brisbane, Hobart New Zealand: Auckland and Christchurch

‘When you have to meet the standards’

The bitterness of poor quality remains long after the

sweetness of a low price has been forgotten.

Shallow Airflow

Deep Airflow

Unijet Cross Section

Cone Centre Cross Section

The Choice is YoursA ducted heating or cooling system is an investment in your families personal comfort. As

much emphasis should be placed on the type of ancillary products as to the type of unit

you purchase.

Smooth StylingOur round ceiling diffusers are manufactured from ABS (Acrylonitrile Butadiene Styrene)

plastic, which is the same type of plastic that is used in products like telephones, fridge

liners and hard hats.

The smooth curve of the outside flange gives an attractive and unobtrusive finish. It is the

same smooth curve that is used on our other plastic diffusers. So when you purchase

Westaflex manufactured products, you get a job that is aesthetically pleasing throughout

your home and built to last.

UnijetUnijets have been designed not to just

‘dump’ air straight down like other

similar diffusers. The Unijet disperses

the air over a greater area because it’s

louvres are at different angles.

This gives a more even temperature

over a greater area.

Cone CentreCone Centres are designed to suit the

reverse cycle systems. Cone Centres

allow adjustable control of the airflow

by moving the centre up or down. This

is achieved by a screwing technique.

Clockwise decreases and shallows the

airflow while anti-clockwise increases

and deepens the airflow.

Unijet cross-section diagram

UNIVENT CEILING DIFFUSERS

Neck Size (mm) Order code

Fixed Blade Moving Blade

225 x 225 DCT1022 DCT0762

300 x 300 DCT1019 DCT0495

360 x 360 DCT1023 DCT0761

375 x 550 DCT1024 DCT0791Univent Diffuser

96

Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

150 266 150 95 232

200 317 200 95 282

250 389 250 102 355

300 435 300 102 405

• Manufactured from ABS plastic.• Designed for either supply or extract ventilation.• When used to supply, the air will be pushed down into the room.• These diffusers are used in heat transfer systems.• Spring loaded fixing clips.• Resistant to scratching and fading.• Positive lock duct tabs.• Adjustable screw in centre cone to ensure a balanced airflow.


150 White DCT1472

200 White DCT1473

250 White DCT1474

300 White DCT1475


Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

150 240 150 95 215

200 290 200 95 260

EGGCRATE ROUND DIFFUSERS

• Manufactured from ABS plastic.• Designed for either supply or extract ventilation.• Spring loaded fixing clips.• Resistant to scratching and fading.• Positive lock duct tabs.

Duct Size (mm) Colour Damper Order Code

150 Ice White - DCT2594

200 Ice White - DCT2595

150 Ice White included DCT2608

200 Ice White included DCT2609


200mm Ceiling Diffuser

150mm Eggcrate Round Diffuser

CEILING DIFFUSERSCONE CENTRE


MANROSE FLAT CEILING DIFFUSERS LOW PROFILE

• High quality designer finish.• Designed to supply air into your home, by pushing the air along the ceiling

and down the walls. Included in SmartVent Home Ventilation Systems.


150 White DCT2208

• High quality designer stainless steel finish - grade 304, Designed for internal extraction where a quality finish is required.


100 Stainless DCT2139




Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

100 140 97 52 105

125 172 120 52 130

150 220 145 62 150


Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

150 220 148 80 190


Designer Ceiling Diffuser

Flat Ceiling Diffuser

MANROSE DESIGNER CEILING DIFFUSERSSTAINLESS STEEL

98

Round Ceiling Diffusers

www.uniflex.com.au

Westaflex / Uniflex Australia Pty Ltd ABN 21 005 072 873

Head Office 140 - 152 Bamfield Rd, Heidelberg West Victoria Australia 3081Postal Address P.O. Box 133 West Heidelberg Victoria 3081 Australiaphone +61 (0)3 9458-2122 fax +61 (0)3 9458-3120 email [email protected]

Branches Throughout Australia & New ZealandAustralia: Melbourne, Sydney, Penrith, Newcastle, Canberra, Dubbo, Adelaide, Perth, Brisbane, Hobart New Zealand: Auckland and Christchurch

‘When you have to meet the standards’

The bitterness of poor quality remains long after the

sweetness of a low price has been forgotten.

Shallow Airflow

Deep Airflow

Unijet Cross Section

Cone Centre Cross Section

The Choice is YoursA ducted heating or cooling system is an investment in your families personal comfort. As

much emphasis should be placed on the type of ancillary products as to the type of unit

you purchase.

Smooth StylingOur round ceiling diffusers are manufactured from ABS (Acrylonitrile Butadiene Styrene)

plastic, which is the same type of plastic that is used in products like telephones, fridge

liners and hard hats.

The smooth curve of the outside flange gives an attractive and unobtrusive finish. It is the

same smooth curve that is used on our other plastic diffusers. So when you purchase

Westaflex manufactured products, you get a job that is aesthetically pleasing throughout

your home and built to last.

UnijetUnijets have been designed not to just

‘dump’ air straight down like other

similar diffusers. The Unijet disperses

the air over a greater area because it’s

louvres are at different angles.

This gives a more even temperature

over a greater area.

Cone CentreCone Centres are designed to suit the

reverse cycle systems. Cone Centres

allow adjustable control of the airflow

by moving the centre up or down. This

is achieved by a screwing technique.

Clockwise decreases and shallows the

airflow while anti-clockwise increases

and deepens the airflow.

• Manufactured from ABS plastic.• Designed for either supply or extract ventilation.• Fixing flange included, screws required.• Adjustable screw in centre cone.


100 White DCT0020

125 White DCT0174

150 White DCT0058

200 White DCT0068

Cone cross-section

Cone Centres are designed to suit the reverse cycle systems. Cone Centres allow adjustable control of the airflow by moving the centre up or down.

This is achieved by a screwing technique. Clockwise decreases and shallows the airflow while anti-clockwise increases and deepens the airflow.

Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

100 149 99 47 98

125 169 125 47 123

150 186 148 50 148

200 235 198 50 198


200mm Ceiling ‘ECO’ Diffuser


CEILING DIFFUSERS ECO DIFFUSER

100

• High quality designer finish available in either white or brushed aluminium silver.• Designed for bathroom extraction that blends into any decor.


150 White DCT2236

150 Silver DCT2237

Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

100 140 98 49 105

125 170 125 65 125

150 200 150 65 157


MANROSE WALL/CEILING GRILLESCIRCULAR

• Concentric circular grille designed for extraction.


100 White DCT2185

125 White DCT2186

150 White DCT2187

Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

150 191 x 191 150 65 157

150 191 x 191 150 65 157


150mm Circular Wall/Ceiling Grille

Designer Wall/Ceiling Grilles

MANROSE DESIGNER WALL/CEILING GRILLESSQUARE

• Low Profile eggcrate design improves airflow in extraction applications.• Twist lock fascia for easy cleaning.• Gib fixing clips included.• Longer spigot for easy duct connection.• Satin Silver & Chrome fascias available.

ACCESSORIES

Duct Size (mm) Description Colour Order Code

100 Circular White DCT1089

100 Square White DCT2223





Duct Size (mm) Description Colour Order Code

125 Square Fashia Gold FAN0754

125 Circular Fascia Satin Silver FAN2069

125 Square Fascia Satin Silver FAN2068

125 Circular Fascia Chrome FAN0757

125 Square Fascia Chrome FAN0755

125 Circular Fascia White FAN0748

125 Square Fascia White FAN0747

150 Circular Fascia Satin Silver FAN2070

150 Square Fascia Satin Silver FAN2071

150 Circular Fascia Chrome FAN0613

150 Square Fascia Chrome FAN0598

150 Square Fascia Gold FAN0597

150 Circular Fascia White FAN0750

150 Square Fascia White FAN0749

125 Spigot White DCT1074

150 Spigot White FAN0656

Duct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

100 140 98 49 115

125 170 120 65 135

150 200 150 65 165

100 140 x 140 98 49 115

125 161 x 161 120 65 135

150 191 x 191 150 65 165


Accessories

150mm Low Profile Wall/Ceiling Grille - Square/Circular

150mm Low Profile Wall/Ceiling Grille


MANROSE WALL/CEILING GRILLESLOW PROFILE


100 White DCT0375

125 White DCT0472

150 White DCT0473

• Improved air-flow characteristics.• Removable insert for easy cleaning.


100 White DCT0025

100 Grey DCT0024

100 Terracotta DCT0026

125 White DCT0041

125 Grey DCT0039


150 White DCT0063

150 Grey DCT0062


200 White DCT0340

230/250 White DCT0073

300 White DCT1979

• Standard grille with some weather protection.• Removable insert for easy cleaning.

Grille DescriptionDuct Size (mm)

Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

Fixed Louvre Grille 100 140 x 140 100 35 105




Fixed Louvre Grille 230/250 285 x 285 230 29 240


Eggcrate Grille 100 140 x 140 100 34 105



150mm Wall/Ceiling Grille Fixed Louvre White

150mm Wall/Ceiling Grille Eggcrate White


MANROSE WALL/CEILING GRILLESEGGCRATE

102

MANROSE WALL/CEILING GRILLESFIXED LOUVRE

Prevents back draughts & weather penetration.

High quality designer stainless steel finish. Stainless Steel Grade 304.


100 White DCT0029

100 Grey DCT0028


125 White DCT0044

125 Grey DCT0042


150 White DCT0066

150 Grey DCT0061


230/250 White DCT2204

300 White DCT1981


100 Stainless Steel DCT2145





Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

Designer Gravity Grille 100 150 x 150 97 52 115



Standard Gravity Grille 100 140 x 140 100 35 105



Standard Gravity Grille 230/250 275 x 275 230 50 240


• The Designer Gravity Grille requires a minimum pressure to open.• 20Pa - 100mm (DCT2145).• 30Pa - 125mm (DCT2146).• 30Pa - 150mm (DCT2147).

MANROSE WALL GRILLESPLASTIC GRAVITY


MANROSE DESIGNER WALL GRILLESSTAINLESS GRAVITY

150mm Weatherproof Cowl

150mm Weatherproof Plastic Cowl

• High quality designer stainless steel finish with stainless steel wire mesh.• Designed for use where adverse weather conditions are experienced.• Manufactured from a Stainless Steel Grade 304.

Mesh and Flap Mesh no Flap

Duct Size (mm) Colour Order Code Order Code

100 Stainless Steel DCT3614 DCT3617



• Comes standard with wire mesh.• Used where adverse weather conditions are experienced.


100 White DCT0018

100 Brown DCT0019

125 White DCT1030

150 White DCT1031

150 White DCT1995*

MANROSE WEATHERPROOF COWLSPLASTIC COWLS


Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

Designer Weatherproof 100 150 x 150 97 52 115



Standard Weatherproof 100 140 x 140 99 35 115




*Comes with Aluminium Fixed Louvre.


100 For 100mm Grilles DCT0371



200-250 For 200mm & 250mm Grilles DCT0373

150 Bird Mesh DCT2263

150 Aluminium Fixed Louvre DCT2599

OPTIONAL INSERTS

104

MANROSE DESIGNER WEATHERPROOF COWLSSTAINLESS COWLS





• High quality stainless steel dome cowl for a modern stylish look.• Designed for exhaust and supply ventilation.• Generally mounted on an external wall, however they can be mounted internally.• Manufactured from a Stainless Steel Grade 304.• Insect mesh included.• This product does not have a backdraught shutter. An Insect mesh is

included


Face Size (mm)


Spigot Length (mm)

Cut-Out Size (mm)

Designer Dome Cowl 100 140 97 52 115



150mm Weatherproof - Stainless Dome Cowl

MANROSE DESIGNER WEATHERPROOF DOMESSTAINLESS DOME COWLS


TENMAT FIRE RATED CEILING VALVESTENMAT FIREFLY FIRE RATED AIR VALVES

Description Face Size Neck Size Weight Order Code

100 mm Fire Diffuser 138Ø 98Ø 0.30Kg DCT2856

125 mm Fire Diffuser 180 123Ø 0.40Kg DCT2789



Tenmat Fire Diffuser


Note

1. Products with the order code showing are generally ex-stock lines - other products are available to order.

106

• Manufactured in high quality aluminium extrusion profiles, powder coated white.• Designed with nylon bushes for efficient, smooth operation.• Deflection blades are adjustable individually.• Standard 20mm blade spacing.• Opposed blade dampers and removable core are available on request.• Special sizes made to order, please state neck size required. POA.

Neck Adaptor Fixed Core Removable Core


300 x 100 DCT2020* DCT1372*

300 x 150 DCT4137

350 x 150 DCT2021* DCT1373*

400 x 100 DCT2022

400 x 150 DCT2023 DCT1374

400 x 200 DCT2024 DCT1375

500 x 100 DCT2025

500 x 150 DCT2026

500 x 200 DCT2027 DCT4135

500 x 300 DCT2028

600 x 150 DCT2029

600 x 200 DCT2030

600 x 300 DCT2031 DCT4133

800 x 150 DCT2032

800 x 200 DCT2033

800 x 300 DCT2034

800 x 400 DCT2035


400 x 100 Double Deflection Wall Diffuser

*Suits Poly Floor Boots - DCT0714, DCT0715, DCT0716 see page 122

DOUBLE DEFLECTION WALL DIFFUSER

Neck Size

252025

45



Face Velocity (m/sec)

1.5 2 2.5 3 3.5 4 4.5 5

Pa 9 16 26 37 50 62 83 102

300 x 100l/sM3/hrNR (dB(A))

38138<15

5118515

6322823

7527226

9032530

10237135

11441141

12946645

300 x 150400 x 100

l/sM3/hrNR (dB(A))

56202<15

7527215

9434224

11441128

13347930

14954135

16860741

18968446


66238<15

8831815

11140324

13247628

15556130

17864335

20072340

22380646


77277<15

10236716

12846224

15355327

17864431

20273135

23083141

25692746

400 x 200500 x 150

l/sM3/hrNR (dB(A))

86309<15

12846216

14251523

16961227

19771430

22581335

25592140

284102946

500 x 200600 x 150

l/sM3/hrNR (dB(A))

113408<15

15054417

18868023

22681627

26395231

301108835

338122440

376136046

600 x 200800 x 150

l/sM3/hrNR (dB(A))

169612<15

22681620

282102023

348125827

395142831

451163235

508183640

573207447

500 x 300600 x 300800 x 200

l/sM3/hrNR (dB(A))

22681616

301108821

376136024

451163228

526190432

602217637

677244841

752272048


310112217

414149622

517187026

620224430

724261835

827299238

931336643

1034374051

TECHNICAL DATA

Materials

• Extruded aluminium A6063.Surface Finish

• Baked white powder coated as standard.• Pattern controller vane is black anodised.Features

• SLLS linear ceiling diffuser can be used in T-bar ceiling suspension system & other ceiling types as well.• The diffuser incorporates curved blade pattern controllers for adjustment of air distribution.• Available in 1 slot to 6 slots.• Approximately 38% free area when blades are fully open.

DIMENSION INFORMATION - DIFFUSER ONLY

Slots Length (L) Width (W) Height (H) Spigot Size (S) Order Code

1 Slot 600mm

Diffuser Neck size +20mm

230mm

150mm DCT2685

900mm 200mm DCT3548

1200mm 150mm DCT2686

2 Slot 600mm 150mm DCT2653

900mm 200mm DCT3549

1200mm 200mm DCT2655

1200mm 300mm DCT2654

1500mm 250mm DCT2688

1800mm 250mm DCT2689


1800mm 300mm DCT2690

SlotsLength (L)

Neck Size (W)

Duct Size (A)

Ceiling Cut Out (B)

Face Size (D)

Order Code

1 Slot 600mm 48mm

L + 10mmW + 10mm

L + 15mmW + 15mm

L + 37mm

DCT2677

900mm 48mm DCT3546

1200mm 48mm DCT2679


900mm 93mm DCT3547

1200mm 93mm DCT2680

1500mm 93mm DCT2682

1800mm 93mm DCT2683


1800mm 138mm DCT2689

DIMENSION INFORMATION - PLENUM ONLY

108

SLOT DIFFUSERSWALL DIFFUSER

Slot Diffuser - Face only

L

W

H

S

Dimensions - Plenum Only

B

A

W

D

48Dimensions - Diffuser Only

L


SlotsSpigot Size

Length


4 8 14 23 33 45 58

m3/hr 51 77 102 128 153 179 204

1 Slot 150mm 600mm L/s 14 21 28 36 43 50 57

NC 26 31 35 38 42

Throw (m) 1.8-3.4 2.7-4.0 3.4-4.6 3.7-5.2 0.4-5.5 4.3-6.1 4.6-6.4


3 8 14 21 31 42 55

m3/hr 77 116 153 192 230 269 306

1 Slot 150mm 1200mm L/s 21 32 43 53 64 75 85

NC 25 30 35 38 41

Throw (m) 0.6-2.7 2.7-4.0 2.7-4.6 3.7-5.2 0.4-5.5 4.3-6.1 4.6-6.4


3 7 12 20 28 39 52

m3/hr 68 107 145 184 221 260 298

2 Slot 150mm 600mm L/s 19 30 40 51 61 72 83

NC 24 29 34 37 41

Throw (m) 0.9-3.7 2.1-5.8 0.4-7.9 5.2-10.1 6.1-11.9 0.7-12.8 8.2-13.7


5 9 14 21 29 39 49

m3/hr 153 213 272 332 391 451 510

2 Slot 200mm 1200mm L/s 43 59 76 92 109 125 142

NC 24 29 33 36 39

Throw (m) 1.5-4.0 2.7-5.2 3.7-6.1 4.3-6.7 5.2-7.3 8.5-7.6 5.8-8.2


4 7 12 18 26 35 45

m3/hr 255 366 476 587 697 808 918

3 Slot 250mm 1200mm L/s 71 102 132 163 194 224 255

NC 24 29 33 37 40

Throw (m) 2.4-5.5 0.4-7.0 5.2-7.9 6.1-8.8 6.7-9.4 7.3-10.4 7.9-11.0

TECHNICAL DATA (WITH PLENUM)

Neck Size (mm) Face Size Order Code

150 x 150 DCT1989*

225 x 225 DCT2002

300 x 300 DCT2003

360 x 360` DCT2004

438 x 438 490 x 490 DCT3757

540 x 540 595 x 595 DCT2005**

• Manufactured in high quality aluminium extrusion profiles.• Flush face finish. • Powder coated white.• Poly neck adaptors see page 115 • Special sizes made to order, please state neck size required. POA.

300 x 300mm Eggcrate Return Grill - Fixed Core

Neck Size (mm)Face Size (mm)

157 x 157 210 x 210

225 x 225 275 x 275

300 x 300 348 x 348

360 x 360 420 x 420

540 x 540 595 x 595


* DCT1970 (157 x 157) Opposed Blade Damper (O.B.D) to suit see page 86.

** 595 x 595mm “lay in” T-rail grille.


EGGCRATE RETURN GRILLES FIXED CORE (ERG)

110

EGGCRATE RETURN GRILLES WITH FILTER (ERHFG)


300 x 300 DCT0962

360 x 360 DCT1257

550 x 550 DCT0966*

550 x 1150 DCT1113

REPLACEMENT FILTER MEDIA

Metric Size (mm) Order Code

300 x 300 DCT1025

595 x 595 DCT1026

1400 x 1000 DCT1061

Rubber Spline DCT1062

• Manufactured in high quality aluminium extrusion profiles.• Hinged removable filters.• Flush face finish.• Powder coated white.• Filter media G2 rated.• Poly neck adaptors see page 115

Neck Size (mm)Face Size (mm)

300 x 300 340 x 340

360 x 360 407 x 407

550 x 550 595 x 595

360 x 360mm Eggcrate Return Grille with Filter

DIMENSIONS WITH FILTER


* 595 x 595mm “lay in” T-rail grille.

Special sizes made to order, please state neck size required. POA.


• Manufactured from high impact polystyrene.• Resistant to scratching and fading.• Quick fix fixing clips, no tools required.• Aluminium eggcrate biscuits powder coated white.


225 x 225 DCT0759

300 x 300 DCT0760

360 x 360 DCT0797

375 x 550 DCT0798

Neck Size (mm) Face Size (mm)

225 x 225 278 x 278

300 x 300 348 x 348

360 x 360 425 x 425

375 x 550 422 x 600

300 x 300mm Eggcrate Return Grill - Face Only



EGGCRATE RETURN GRILLES FACE ONLY (ERG)

112

With Fixing Flange No Filter With Filter Media

Metric Size (mm) Order Code Order Code

375 x 550 DCT0729 DCT0805*

UNI LOUVRE RETURN GRILLESLRG MODEL

• Manufactured from V-Zero fire rated ABS plastic AS/NZ 1530.3.• Easy fit pressed metal fixing flange included.• With or without filter media, G2 rated.• Replacement filter cloth DCT3250

*Filter media G2 rated where applicable.

Neck Size (mm) Face Size (mm)

375 x 550 428 x 603


375 x 550mm Uni Louvre Return Grille

CEILING MOUNTED GRILLESREMOVABLE CORE EGGCRATE GRILLES

Neck Size (mm) Face Size (mm) Order Code

140 x 140 180 x 180 DCT3566

190 x 190 230 x 230 DCT3636

• Resistant to scratching and fading.• Manufactured from aluminium and powder coated white as standard.


114

CUSHION BOXESSIDE ENTRY - PLASTIC

NUDE INSULATED


225 x 225 - 150 Ø DCT0993 DCT1004

225 x 225 -200 Ø DCT0992 DCT1003

300 x 300 - 200 Ø DCT1006

300 x 300 - 250 Ø DCT0971 DCT0972

300 x 300 - 300 Ø DCT0994

375 x 375 - 300 Ø DCT0996

450 x 450 - 350 Ø

450/435 x 450/435 300/250/200 Ø

DCT1356* DCT1417*

550 x 375 -350 Ø DCT2986

• Low profile to suit suspended ceilings or in between floors (double storey).• Manufactured from HDPE, fits poly and aluminium diffusers.

* Cut to suit size required.

Cushion Box (Plastic) - Side Entry


Metric SizeA Length

BHeight

CSpigot length

DNeck Size

Spigot Size

225 x 225-150 310 196 90 226 115 x 180

225 x 225-200 310 196 90 226 115 x 226

300 x 300-200 395 200 90 304 110 x 226

300 x 300-250 395 200 90 304 110 x 330

STEPPED CUSHION BOX

Metric SizeA Length

BHeight

CSpigot length

DNeck Size

Spigot Size

450/435 x 450/435

-200 540 250 90 450 125 x 235

-250 540 250 90 450 145 x 300

-300 540 250 90 450 190 x 350

A

B

D

C

Dimensions for Nude/Insulated

A

B

C

D

Dimensions For Stepped Cushion Box


• Poly Adaptor “Snaps-On” to plastic diffusers, no tools or fixing required.• Manufactured from high impact polystyrene, positive lock duct tabs.• Poly neck adaptors to suit UniVents, CD2000 and some aluminium diffusers.


250-150 DCT1142

250-200 DCT0965

*To CONVERT 250mm Spigots.

NO DAMPER WITH DAMPER


225 x 225-150 DCT0681 DCT0683

225 x 225 -200 DCT0545 DCT0741

300 x 300-250 DCT0497* DCT0498*

300 x 300-300 DCT0509 DCT0499

375 x 375-250 DCT0547* DCT0557*

375 x 375-300 DCT0549 DCT0559

375 x 375-350 DCT0553 DCT0661

375 x 375-400 DCT0555 DCT0804


450 x 450 - 300/350 DCT1406

450 x 450 - 400/450 DCT1407

550 x 550 - 300/350 DCT1408

550 x 550 - 400/450 DCT1409

550 x 550 - 500/550 DCT1410

Poly Adaptor & Poly Adaptor with Damper

250-150mm Spigot

450 x 450 - 300/350 Stepped Spigot

NECK ADAPTORS

STEPPED SPIGOT - NO DAMPER

116

A

C

B

Metric Size (mm)ASquare Neck (mm)

BSpigot Diameter (mm)

CSpigot Length (mm)

225 x 225 - 150 214 146 70

225 x 225 - 200 214 198 70

300 x 300 - 250 287 248 70

300 x 300 - 300 287 298 70

375 x 375 - 250 360 248 70

375 x 375 - 300 360 298 70

375 x 375 - 350 360 348 70

375 x 375 - 400 360 398 70

Metric Size (mm)ASquare Neck (mm)

BSpigot Diameter (mm)

CSpigot Length (mm)

450 x 450/300/350 448 295/345 60/60

450 x 450/400/450 448 395/445 60/60

550 x 550/300/350 550 295/345 60/60

550 x 550/400/450 550 395/445 60/60

550 x 550/500/550 550 495/545 60/60

A

B

C

Dimensions A

DIMENSIONS B

Dimensions B

NECK ADAPTORS

DIMENSIONS A

DUK Jet Nozzle

TJN Jet Nozzle

VDW Swirl Diffuser

TROX JET NOZZLESDUK

TROX JET NOZZLESTJN

Model Flow Rates l/s Nom. Size (mm) Order Code

DUK-V/100 < 39 100Ø

DUK-V/125 < 50 125Ø

DUK-V/160 23 - 69 160Ø

DUK-V/200 29 - 85 200Ø DCT3157

DUK-V/250 37 -106 250Ø DCT3158

DUK-V/315 20 - 150 315Ø DCT3159

DUK-V/400 65 - 195 400Ø DCT3160


TJN/160/D 25 - 70 160Ø DCT3325

TJN/200/D 30 - 120 200Ø DCT3326

TJN/250/D 50 - 190 250Ø DCT3327

TJN/315/D 120 - 300 315Ø DCT3328

TJN/4000/D 190 - 450 400Ø DCT3329

TROX SWIRL DIFFUSERSVDW

Model (Face Plate Only) Flow Rates l/s Nom. Size (mm) Order Code

VDW-Q-Z/300x8/O/RAL9010 15 -200 298 x 298 DCT3135

VDW-Q-Z/300x8/O/RAL9010 PLQ 15 - 200 598 x 598 DCT3140

VDW-Q-Z/400x16/O/RAL9010 30 -250 398 x 398 DCT3136

VDW-Q-Z/400x16/O/RAL9010 PLQ 30 -250 598 x 598 DCT3141

VDW-Q-Z/500x24/O/RAL9010 45 - 330 498 x 498 DCT3137

VDW-Q-Z/500x24/O/RAL9010 PLQ 45 -330 598 x 598 DCT3551

VDW-Q-Z/600x24/O/RAL9010 60 -440 598 x 598 DCT3138

VDW-Q-Z/600x48/O/RAL9010 120 - 600 598 x 598 DCT3139

VDW-Q-Z/825x72/O/RAL9010 220 - 850


FD Swirl Diffuser

AIRNAMIC Swirl Diffuser

VDL Swirl Diffuser

VFL Volume Flow Limiter


FD-Q-Z/300/0/0/RAL9010 40 - 55 298 x 298 DCT3130

FD-Q-Z/400/0/0/RAL9010 50 -110 398 x 398 DCT3131

FD-Q-Z/500/0/0/RAL9010 60 -145 498 x 498 DCT3132

FD-Q-Z/600/0/0/RAL9010 80 -165 598 x 598 DCT3133

TROX SWIRL DIFFUSERSFD


AIRNAMIC-Q-Z/300L/0/RAL9016 30 - 100 300 x 300 DCT3161

AIRNAMIC-Q-Z/300H/0/RAL9016 40 -135 300 x 300 DCT3162

AIRNAMIC-R-Z/400/0/RAL9016 60 - 140 400Ø DCT3163

AIRNAMIC-Q-Z/600/0/RAL9016 130 -385 600 x 600 DCT3164

AIRNAMIC-R-Z/600/0/RAL9016 130 -385 600Ø DCT3165

TROX SWIRL DIFFUSERSAIRNAMIC


VDL-0/315/0/RAL9010 66 - 340 315Ø DCT3176

VDL-0/400/0/RAL9010 93 - 500 400Ø DCT3178

VDL-0/630/0/RAL9010 230 - 1100 630Ø

VDL-0/800/0/RAL9010 318 - 1400 800Ø

TROX SWIRL DIFFUSERSVDL


VFL/80 4 - 25 80Ø DCT3392

VFL/100 4 - 33 100Ø DCT3393

VFL/125 11 - 57 125Ø DCT3394

VFL/150 14 - 97 150Ø DCT3395

VFL/200 17 - 158 200Ø DCT3396

VFL/250 35 - 250 250Ø DCT3397

TROX VOLUME FLOW LIMITERSVFL

118

• Designed for external ventilation.• Special sizes made to order, please state neck size required. POA.• Bird Mesh attached.

Face Size (mm) (N) Finish Neck Size (W x H) Order Code

200 x 200 Natural Anodised 195 x 195 DCT3638


210 x 210 White 160 x 160 DCT2579




375 x 375 Natural Anodised DCT3336




• Manufactured from galvanised steel.• Neck adaptors to suit WPLG above.


170 x 170 - 150 Ø DCT1434

210 x 210 - 200 Ø DCT1435

290 x 290 - 250 Ø DCT1436

330 x 330 - 300 Ø DCT1437

410 x 410 - 350 Ø DCT1438

NECK ADAPTOR FOR WEATHERPROOF LOUVRE GRILLE

Model MaterialsThickness Neck Adapter

Size AHole Size B

Face Size CFrame Blade

WPLGExtruded Aluminium A6063

1.2 1.2N+10N+10

N+20N+20

N+60N+60

410 x 410mm Weatherproof Louvre Grille

410 x 410mm Neck Adaptor for Weatherproof Louvre Grille

N

WEATHERPROOF LOUVRE GRILLES(WPLG)



• Manufactured from V2 fire rated high impact polycarbonate.• Positive shut-off, resistant to scratching and fading.• Improved air flow control.

• Powder-coated.• Positive shut-off.

FLOOR REGISTERS SIDE FLOW METAL

Neck Size (mm) Colour Order Code

300 x 100 Beige DCT2213

350 x 150 Beige DCT2214


300 x 50 Beige DCT2210

300 x 50 White DCT2209

350 x 50 Beige DCT2212


KICK RAIL


300 x 100 Beige DCT0914

300 x 100 Mushroom DCT0810

300 x 100 Grey DCT0712

300 x 100 White DCT0956

300 x 100 Chocolate DCT1137

300 x 100 Black DCT0980

350 x 150 Slate Grey DCT0749

350 x 150 Beige DCT0713

350 x 150 White DCT1052


350 x 150 Black DCT0959

350 x 150 Baltic Pine DCT1266

STANDARD

Standard

Kick Rail

Floor Register - Side Flow Poly

FLOOR REGISTERS SIDE FLOW POLY

120

DescriptionMetric Size (mm)

Face Size (mm)

Neck Size (mm)

Spigot Length (mm)

Floor Register 300 x 100 345 x 140 298 x 98 50

Floor Register 350 x 150 392 x 190 348 x 148 63

Kick Rail Floor Register 300 x 50 345 x 100 300 x 51 40

Kick Rail Floor Register 350 x 50 395 x 100 348 x 51 46

TECHNICAL DATA

FLOOR REGISTERS - COLOUR CHART

• Manufactured from V2 fire rated high impact polycarbonate.• Positive shut-off, resistant to scratching and fading.• Improved air flow control.



300 x 100 Beige DCT0743

300 x 100 White DCT0957


350 x 150 Beige DCT0752


350 x 150 White DCT1059


Floor Register - Front Flow Poly

FLOOR REGISTERSFRONT FLOW POLY

Simx Limited | www.simx.co.nz | [email protected] 121

Grey Black Chocolate

Beige White Off White

• Poly Boot manufactured from high density polyethylene.• Metal Boot manufactured from Galvanised Steel.• UV. stabilised.• Robust, heavy duty with smooth internal lines.• Complete with collar and damper.• Positive lock duct tabs, nail holes pre-puncheded.

POLY METAL UNIBOOT


300 x 50 - 150 DCT2215

350 x 50 - 150 DCT2216

300 x 100 - 150 DCT0714 DCT1449

350 x 150 - 200 DCT0715

350 x 150 - 250 DCT0716

Recommended Airflow:

• 150mm duct approx. 65 l/s.• 200mm duct approx. 90 l/s.• 250mm duct approx. 140 l/s.

Poly

Metal Uniboot

BOOT DIMENSIONS POLY

Metric Size (mm)Neck Size (mm) A x B

Spigot Size (mm) C x D

Boot Length (mm) E

300 x 100 - 150 Ø 300 x 100 180 x 90 220

350 x 150 - 200 Ø 355 x 150 250 x 110 250

350 x 150 - 250 Ø 355 x 150 340 x 110 250

A B

C

E

Dimensions: UniBoot

A B

C

E

D

Dimensions: POLY

Metric Size (mm)Neck Size (mm) A x B

Spigot Size (mm) C x D

Boot Length (mm) E

300 x 50 - 150 Ø 300 x 50 150 Ø 250

350 x 50 - 150 Ø 350 x 50 150 Ø 250

BOOT DIMENSIONS METAL

122

FLOOR BOOTS

Face Size (mm) Neck Size (mm) Order Code

200 x 150 188 x 146 DCT3540

200 x 200 190 x 190 DCT3489

300 x 300 290 x 290 DCT3490

350 x 200 340 x 190 DCT3635

595 x 595 540 x 540 DCT3491

• Manufactured in high quality aluminium powder coated white.• Special sizes made to order, please state neck size required. POA.• Indent Items.• Two options available, fixed core (LRG) or filtered removable core (LRGF).

FIXED CORE (LRG)

REMOVABLE CORE (LRGF)


400 x 350 DCT1382 DCT1377

400 x 500 DCT1383 DCT1378

400 x 600 DCT1384 DCT1379

400 x 900 DCT1385 DCT1380

500 x 400 DCT1386 DCT1381

DOOR RELIEF AIR GRILLES(DRAG)

• Natural anodised aluminium.• Including backing flange.• 95% light proof.• Special sizes made to order. POA.


300 x 300 DCT3486

450 x 150 DCT1387

450 x 200 DCT1388

450 x 250 DCT1389

450 x 300 DCT1390

450 x 450 DCT1391

500 x 300 DCT3487

600 x 150 DCT1392

600 x 200 DCT1393

600 x 250 DCT1394

600 x 300 DCT1395

600 x 350 DCT1396

600 x 400 DCT1397

600 x 450 DCT1398

600 x 600 DCT1399

LRGF & LFGLouvre Return Air Grille

Door Relief Air Grille


LOUVRE RETURN AIR GRILLES(LRG)

Plate Size (mm) Colour Order Code


245 x 80 Chrome DCT2195

245 x 160 White DCT2196


245 x 245 White DCT2198


ADJUSTABLE VENT

Plate Size (mm) Colour Order Code



245 x 160 White DCT2190


245 x 245 White DCT2192


MANROSE WALL/CEILING PLATE GRILLESPLATE FACE

Duct Size (mm) Grille Type Colour Order Code

150 Fixed Louvre White DCT0352

150 Gravity Shutter White DCT0353

230 Fixed Louvre White DCT0354

• For situations where no spigot is required.

• Manufactured from PVC in either white or chrome.• Designed for use when make-up air is required.• Fixed Louvre provides maximum airflow.• Adjustable Vent can be fully closed off when not required.

MANROSE DOOR GRILLES


Door Vent Internal Door Ventilator Grille FAN0159

• This door grille allows make-up air into the room.• Dimensions: 455mm (h) x 90mm (w) to fit door with depth of 33mm.

Wall/Ceiling Plate Grilles - Adjustable Vent

Wall/Ceiling Plate Grilles - Fixed Louvre Vent

Wall/Ceiling Plate Grilles - Plate Face

MANROSE WALL/CEILING PLATE GRILLESFIXED LOUVRE VENT

Manrose Door Grille Internal Door Vent

124


DCT0708 and DCT0709Pressure vs Volume

100

80

60

40

20

0

Pres

sure

(Pa)

0 50 100 150 200 250

Volume (litre/sec)

GENERAL PURPOSE COWLS - LOW PROFILELOW BACK PRESSURE


150 General Purpose Cowl DCT0708

150 Heavy Duty Cowl DCT0709

• Added exhaust aperture area and deep vent coverage.• Recommended where high winds in exposed locations may drive rain into the vent.• Also recommended for use in high airflow air intake systems to prevent rain being

sucked into the system.

Models A B

DCT0708 275 125

DCT0709 275 140

Performance - DCT0708/DCT0709


150mm General Purpose Cowl

150mm Heavy Duty Cowl

ROOF COWLS

A

BB

A

Dimensions: Heavy Duty Cowl

Dimensions: General Purpose Cowl


150 General Purpose Kit DCT0172

150 Heavy Duty Cowl Kit DCT0710

150 General Purpose Lead Flashing Kit DCT1095

200 Medium Duty Cowl Kit DCT3603

200 Heavy Duty Cowl Kit DCT3604

PLASTIC REDUCERS FOR HDPE THRU-ROOF TUBE (FOR THRU-ROOF KITS)

• Reducers fit to the bottom of HDPE tube to adapt to smaller duct diameters where required.

Metric Size (mm) Description Order Code

150:125 150:125 reducer DCT2066

150:100 150:100 reducer DCT2122


125 Angled Roof Kit DCT2205

• General purpose through roof kit for smaller applications. 110mm PVC pipe - suitable fpr 125 flexible ducting.

• To be mounted on tile roofs.• Includes kit - Cowl, 0.5m of tube & weathering slate included.

MANROSE ANGLED ROOF COWL KIT

• General purpose cowl included.• 0.5m HDPE Tube included.• Flashing included (for metal based roofs).• All fittings supplied.• Optional lead Flashing available (extra cost - refer to Roof Flashings page 127).

Note: Lead Flashing (DCT0190) required for concrete tile roofs.

126

150mm General Purpose Kit

Angled Roof Kit

ROOF COWL KITS WITH FLASHING & HDPE TUBE

• Kit comes complete with a ASA plastic cowl construction, with or without fan incorporated, mounting tubes, aquaseal roof flashing & power lead flashing.


• High quality ASA plastic cowl construction, with fan incorporated, for longevity of operation.


COMMERCIAL THRU ROOF FAN KITS


250mm Commercial Cowl - - DCT2238

250mm Commercial Fan Cowl Ctr’fgl 178 l/s, 640 m3/hr FAN2120

250mmCommercial Fan Cowl - High Performance





250mm Commercial Kit - - DCT2241

250mm Commercial Fan Kit Ctr’fgl 178 l/s, 640 m3/hr FAN2122

250mmCommercial Fan Kit - High Performance




• Standard Model - operates from remote switch (not supplied).

ROOF FLASHINGS


Flashing Roof Flashing - fits 110-160mm DCT0180

Tiledek Roof Flashing - For use on concrete tile, clay tile and slate roofing

DCT0190

0.5m HDPE Tube 150mm DCT0183

Stitching Screws (for roof fastening) FAN0400


250mm Hyper Fan System

250mm Commercial Fan Kit

THRU ROOF MOUNTED FANSCOMMERCIAL THRU ROOF FAN

Roof Flashings

• There are three ducting options available, for the kitchen rangehood. Through an adjacent wall, through the soffit (under the eave) or up through the roof.

• Semi-Rigid ducting is used in our top of the range systems to reduce the rangehood system noise and increase air flow performance.

• Fully complies to AS/NZS 60335.2.80.


125 Rear Vent - Gravity Grille DCT1162

150Top & Rear Vent - Weatherproof Cowl

DCT2592


150 Thru Soffit DCT1161

150 Thru Soffit - Galv Tube DCT1259

150 Thru Soffit - Semi Rigid DCT2323

FLASHING


150 Thru Roof - Iron DCT2324

150 Thru Roof - Tiled DCT2325

• For added weather protection use the weatherproof cowl as included in DCT2592.

• All systems include 3 metres of Aluminium Duct.• Galv Tube system also includes 900mm of Solid Tube.

THRU WALL RANGEHOOD DUCTING KITS

SOFFIT RANGEHOOD DUCTING KITS

THRU ROOF RANGEHOOD DUCTING KITS

Iron Roof Tiled Roof

Soffit Rangehood Ducting Kits

Thru Roof Rangehood Ducting Kits

Thru Wall Rangehood Ducting Kits

128

MANROSE RANGEHOOD DUCTING KITS

200mm Outlet Fan

• This ducting kit is designed for inverted and wall mounted dryers.• Free standing dryers on the floor will require extra rectangular ducting

and connector (Order Code: DCT0013 & DCT0014).• These ducting kits suit dryers with a 100mm outlet. The square to round

elbow will fit snugly onto most 100mm dryer outlets.

Kit Includes:

• 3m Flexible aluminium Aluduct (rated -30°C to 150°C).• 0.75m Flat channel duct.• 2 x Rectangular to Round 90° elbow bends.• 100mm white eggcrate grille.• All fixing and fittings.


100 DCT1263


150 HeatTrans Extension Kit DCT2101

150 SmartVent Extension Kit DCT2276

Kit Includes:

• Designed to extend your home ventilation or heat transfer systems to additional rooms.

• 1 x Y-Branch.• 1 x 3 metres - 150mm Acoustic Insulated Ducting.• 1 x Adjustable Circular Diffuser.• All fixing and fittings included.

DRYER DUCTING FEATURES

PRO SERIES EXTENSION KIT

Suitable for a range of fans including the following models:

• Airflow Sunshine 6600A.


150 Thru-Soffit DCT0167

150 Thru-Roof DCT0171



MANROSE DUCTING KITSFOR HEAT/FAN/LIGHT UNITS - 220MM OUTLET FAN

Dryer Ducting Kit

Pro-Series Extension Kit


MANROSE DRYER DUCTING KITSREAR VENT THRU WALL

Note

Adaptor to fit to the rear of the fan, 3 metres of flexible ducting and an exterior louvred grille.

Thru Soffit Kits include:

Adaptor to fit to the rear of the fan, 3 metres of flexible ducting and an exterior louvred grille.

Thru Roof Kits include:

Adaptor to fit to the rear of the fan, 1.5 metres of flexible ducting, 0.5 metres of 150mm high density polyethylene (HDPE) tubing, a tube fastening bracket, an aluminium cowl and roof flashing plus approved fastenings.

MANROSE DUCTING KITS FOR OPEN BACK FANS


• HPM Exhaust Fan R621/1.• ARLEC 200 Ceiling Fan.• IXL Vent’n’Lite 100- 10310, IXL Ventair - 10320.• Mistral 6250-0.






• HPM Models: Exhaust Fan R621/2, Fanlight R620.• ARLEC 250 Ceiling Fan.• IXL Ventair - 10325.• Mistral 6230-0.











• HPM Models: Instant Heat 2 R622/1A, Instant Heat 4 R622/2A.

250MM OUTLET FAN

300MM COWL

340MM COWL

250mm Outlet FAN

300mm Cowl

130 148

MANROSE DUCTING KITSFOR HEAT/FAN/LIGHT UNITS

TABLE OF CONTENTSHOME VENTILATION AND HEAT TRANSFER

SmartVent Positive Selection Guide 132

SmartVent Positive System Ducting Guide 133

SmartVent Positive Specifications and Controllers 134

Single Room Heat Recovery 135

SmartVent Synergy Selection Guide 137

SmartVent Synergy System Ducting Guide 139

SmartVent Synergy How They Work 140

SmartVent Accessories 141

HeatTrans Systems 142

131

132

3m x 150mm Acoustic Insulated

150mm 150mm

150mm

150mm

SMARTVENT POSITIVESELECTION GUIDE

The size of the home (m2)

Evolve temperature and humidity sensor capabilities and Tablet

Supply Outlets SmartVent System Order Codes

Up to 70m² -

1 SV01C FAN2023

2 Extension Kit DCT2276

1 SV01 (no controller) FAN1056

Up to 100m²

Yes2 SV02E FAN2113


No2 SV02 FAN0939


Up to 280m²

Yes4 SV04E FAN2115

5 - 6 Extension Kit/s DCT2276

No4 SV04 FAN1057


Up to 560m²

Yes6 SV06E FAN2117


No6 SV06 FAN1064


IMPORTANT

• If you exceed the number of rooms listed in the selection guide above, the performance of the system will not work as designed.• Maximum outlets are listed above, do not exceed the number listed.• For the SV06 systems, a total of 6 extension kits can be added, however do not exceed 3 extension kits per branch of the system.

* DCT1491 / DCT3418 consist of 2 x 1kW units for installation into each branch of an SV06/E system. ** When adding more than one PTC Room Heater into the digital system contact Simx Technical Support for advice on 09 259 1660 BEFORE PLACING ORDER.

Kit SV01 SV01C SV02 SV02E SV04 SV04E SV06 SV06E

Second Air Source Kit - DCT2134 DCT2134 DCT2128 DCT2135

Outdoor Air Supply Kit FAN6264 FAN6264 FAN6264 - - -

Heat Transfer Kit - - FAN2027 FAN2028FAN2028 (1 branch)

FAN4438 (both branches)

Tempering Heater

1 kW DCT2123 DCT1226 DCT1226 DCT3478 DCT1483 DCT3231 DCT1483 DCT3231

2 x 1 kW - - - - - - DCT1491* DCT3418*

2 kW - - - - DCT1484 DCT3230 DCT1484 DCT3230

Digital PTC Room Heater

1.6 kW DCT4039** DCT4039** DCT4039** - DCT4039** - DCT4039** -

2.4 kW DCT4040** DCT4040** DCT4040** - DCT4040** - DCT4040** -

Evolve PTC Room Heater

1.6 kW - - - DCT4037 - DCT4037 - DCT4037

2.4 kW - - - DCT4038 - DCT4038 - DCT4038

Additional Fan Kit – 150mm

- FAN5836 FAN5836 FAN5836 - FAN5836

Additional Fan Kit – 200mm

- FAN5837 FAN5837 FAN5837 - FAN5837

Additional Outlet/s

Optional Extras

Kit SV01 SV01C SV02 SV02E SV04 SV04E SV06 SV06E

Additional Outlet DCT2276

Note: Exceeding the number of rooms listed in the Selection Guide (by product) may affect the performance of the system and should be reviewed with SmartVent prior to purchase and installation.


SMARTVENT POSITIVESYSTEM DUCTING GUIDE

Note: For SV06 systems the ducting diagram below is duplicated.

SV01 / SV01C

SV04 / SV04E

SV06 / SV06E

SV02 / SV02E

134

SMARTVENT POSITIVESPECIFICATIONS & CONTROLLERS

Kits SV01/SV01C SV02/SV02E SV04/SV04E SV06/SV06E

No Controller (SV01 only) FAN1056

Digital Controller (SV01C) FAN2023 FAN0939 FAN1057 FAN1064

Evolve Tablet controller (E Models) FAN2113 FAN2115 FAN2117

Specifications SV01/SV01C SV02/SV02E SV04/SV04E SV06/SV06E

House size* up to 70m² up to 100m² up to 280m² up to 560m²

Max. Air Flow 620 m³/hr 620 m³/hr 920 m³/hr 1840 m³/hr

Fan Type (Centrifugal) 150mm 150mm 200mm 2x 200mm

Fan Speeds 3 3 3 3

Supply Outlets 1 2 4 6

Default Air Source Roof space Roof space Roof space Roof space

Sound level 47 dB(A) 47 dB(A) 53 dB(A) 53 dB(A)

Max Operating Temperature 60 °C 60 °C 60 °C 60 °C

Min. setting 0 °C 0 °C 0 °C 0 °C

Max. setting 35 °C 35 °C 35 °C 35 °C

Operating hysteresis temperature - 2 °C 2 °C 2 °C

Minimal Differential - 5 °C 5 °C 5 °C

Temperature Accuracy (at source) - ± 1 °C ± 1 °C ± 1 °C

Power Supply (Must be mains earthed)

220-240 VAC

50 Hz

220-240 VAC

50 Hz

220-240 VAC

50 Hz

220-240 VAC

50 Hz

Controller Connection - / 10m RJ45 10m RJ45 / Wireless 10m RJ45 / Wireless 10m RJ45 / Wireless

Filter/s F7 (Inline) F7 (Inline) F7 (Inline) F7 (Inline)

Positive EvolveThe Evolve controller operates on the humidity level or temperature in and around the home.

Positive DigitalThe Positive digital controller uses the temperature in the roof space and your living area* to manage ventilation.

* If heat transfer upgrade is installed.

Evolve Upgrade for Digital Controlled Systems DCT3432

Upgrade Digital SmartVent Systems to Positive Evolve. Contains all you need to convert SmartVent Positive Digital to SmartVent Positive Evolve.

DCT3432

This single room heat recovery fan meets the performance requirements for continuous ventilation under the NZ Building Regulations. With a 100mm diameter heat recovery outlet, this unit has low energy consumption and low noise levels.

Synergy Single Room Heat Recovery can be set to run continuously at 6l/s (for rooms up to 25m2)* or 9l/s (for rooms up to 37m2)*, boosting up to 13l/s, recovering energy from the extracted air and returning it to the dwelling.

The unique, compact heat exchanger has a temperature efficiency up to 80%, saving energy on heating and reducing your carbon footprint while providing ventilation.

• Constant trickle ventilation (24 Hours, 7 Days) with airflow boost option.• Supply & extract airflows are separated. This means that any moisture

extracted from the room is not re-introduced.• Low energy consumption.• Low noise.• Security - reduces risk of theft as windows are not required to be left open.• Health - introduces fresher, drier air from outside helping to reduce condensation

and improve air quality.• Can be switched to ‘extract only’ if desired.• 5 year Warranty.

02Moist/stale air is extracted from the home.01

Extracted moist/stale air exits the home.02

Fresh drier air supplied from outside.03

Warmed supply air enters the home.04

01

03

04

WORKING DIAGRAM

DescriptionSuitable for Wall Thickness (mm)

Order Code

Synergy Single Room Heat Recovery - Standard Up to 320 FAN4439

Synergy Single Room Heat Recovery - Long 321-460 FAN5945


SINGLE ROOM HEAT RECOVERYOVERVIEW

Stale Warm Air from dwelling

Stale Cool Air Out

Fresh Warm Air returning to dwelling

Fresh Cold Air In

Fresh Warm Air returning to dwelling

DIMENSIONS (MM)

Order Code A B C D E F G

FAN4439 190 266 262 117 496 99 321

FAN5945 190 266 262 117 636 99 461

A D F

EØ

100B C

E

GC

D

HEAT EXCHANGER DIAGRAM

PERFORMANCE

Extract Performance l/s Power Consumption Watts Sound @dB(A)*

ModelTrickle Low

Trickle High

BoostTrickle Low

Trickle High

BoostTrickle Low

Trickle High

Boost

FAN4439/ FAN5945

6 9 15 3.2 5.7 26.6 20 22 36

*Octave band frequency range of 250Hz to 4KHz at 3m. Unit mounted on a reflective surface.

A

B

F

136

SINGLE ROOM HEAT RECOVERYOVERVIEW.


SMARTVENT SYNERGYSELECTION GUIDE

• These recommendations are based on the standard components in the system.• This selection guide assumes 2.4m stud height, if greater please increase the square metre size by 4% for every 0.1 metre.

For example for a 2.8m stud height, increase your house size by 16%.• If you choose to exceed the number of rooms listed in the selection guide above, the performance of the system will be affected.• This selection guide assumes that there is sufficient ceiling space to install all componentry.• By adding additional outlets to the system you are simply dividing the available air amongst more rooms. Extra duct may be

required depending on the size & layout of the home. See accessories on page 141.• For larger homes please contact SmartVent for technical advice.• A SmartVent Synergy system with in-line tempering heaters is not intended to be a substitute for an effective heating system in

the home.• An Inline PTC Room Heater is an effective room heating solution providing fresh air warmed to a comfortable temperature.

Additional Information

The size of the home (m2)Supply Rooms

Extract Rooms

SmartVent Synergy System

Order Code

Up to 150m2

3 1 Synergy 190E FAN2177

4 2 Supply & Extract Extension KitsDCT2276 Supply KitDCT2289 Extract Kit



Up to 250m23 1 Synergy 2025E FAN6067


Up to 350m2



5 2 Synergy 405 FAN2191


Kit Synergy 190E Synergy 1015E Synergy 2025E Synergy 3035E Synergy 405

Second Air Source DCT4017 Included

Heat Transfer FAN2027 FAN2027 FAN2027 FAN2027 -

Tempering Heater

1 kW DCT3478 DCT3231 DCT3231 DCT3231 DCT1483

2 kW - DCT3230 DCT3230 DCT3230 DCT1484

TSC PTC Room Heater

1.6 kW - - - - DCT4039

2.4 kW - - - - DCT4040

Evolve PTC Room Heater

1.6 kW DCT4037 -

2.4 kW DCT4038 -

Core By-pass Kit FAN2172 Included Included Included Included

Heat Boost - - - - Included

Remote Sensor - - - - FAN2047

Optional Extras

138

SMARTVENT SYNERGYSELECTION GUIDE

Note: Exceeding the number of rooms listed in the Selection Guide (by product) may affect the performance of the system and should be reviewed with SmartVent prior to purchase and installation.

Additional Outlet/s & Extracts

Kit Synergy 190E Synergy 1015E Synergy 2025E Synergy 3035E Synergy 405

Additional Outlet DCT2276 DCT4015 DCT4015 DCT4015 DCT2334

Additional Extract DCT2289 DCT4016 DCT4016 DCT4016 DCT2335

DCT2276

DCT2289

DCT4015

DCT4016

DCT2334

DCT2335


SMARTVENT SYNERGYSYSTEM DUCTING GUIDE

Note: The layouts below are intended as a guide only, refer to the Kit Contents list and latest system installation manual for the specific product details and layout.

Synergy 1015E / 2025E / 3035E

Synergy 405

OA = Outside Air SA = Supply Air RA = Return Air EA = Exhaust Air

Synergy 190E

SMARTVENT SYNERGYHOW THEY WORK

140

Synergy 190E Synergy 1015E / 2025E / 3035E

Synergy 405

Extracted moist/stale air exits the home, Fresh drier air supplied from the roof cavity or outside,Moist, humid air is extracted from the home, Warm supply air enters the home

No Condensation Drain

SMARTVENTACCESSORIES


INSULATED DUCTING

150mm diameter x 3m DCT0583




DUCT FASTENERS

Hanging Strap DCT2299

Duct Tape 48mm x 5m DCT0173



DUCT CONNECTORS

150mm metal DCT0723

200mm metal DCT0724

FIXED LOUVRE GRILLES

125mm White DCT0041

150mm White DCT0063

200mm White DCT0340

CONTROLLER SOFTWARE UP-GRADE

Positive Pressure Digital Up-grade to(Software V3.00)

FAN2065

RJ45 to RJ45 Connector FAN2408

CONNECTION ACCESSORIES

MANROSE FLAT CEILING DIFFUSER

150mm White DCT2208





ACOUSTIC INSULATED DUCTING

UNILOK NUDE DUCTING





150/200 Centrifugal Fan

DCT2297

150/200 Mix Flow Fan DCT2298

NOISE REDUCTION FAN HOUSING

REPLACEMENT FILTERS

G4 Sock DCT1411

G4 Filter DCT2221

F7 Filter DCT2093

F7 with Carbon Filter DCT2277

HEPA with Carbon Filter

DCT2278

EXTENSION LEADS

3m Fan lead (4 wire) FAN2190

3m Heater or Damper lead (3 wire)

FAN2194

150-150-150 DCT1233

200-150-150 DCT0379

Y BRANCH

HeatTrans uses excess heat to warm other areas of the home by transferring it from one room to multiple rooms. HeatTrans is the professional brand in heat transfer systems and is the brand of choice for electrical contractors.

Leading the market for over 15 years, HeatTrans is at the forefront of product development and innovation and are the only heat transfer systems using acoustic insulated ducting and digital touch screen controllers.

HOW DOES HEATTRANS WORK

MODEL Order Code

HeatTrans One Room Kit FAN0325

HeatTrans Two Room Kit FAN0337

HeatTrans Three Room Kit FAN0338

Pro-Series One Outlet Extension Kit

DCT2101

HeatTrans Summer-Vent Extension Kit

DCT1481

HeatTrans Thru Wall Kit FAN0005

MODELS

AUTOMATED THERMOSTAT

142

HEATTRANS SYSTEMS

01 Excess heat from your heat source will rise to ceiling level where it is trapped. This excess heat can reach temperatures of 30-35°C.

Air moves from the bedrooms back to the lounge creating a natural recirculation of warm air throughout the home.

This excess heat can be effectively transferred to other rooms using a high quality fan and acoustic insulated ducting.

02

03


UT-T1Touch Screen Automated Thermostat

FAN5555

• High quality, easy to use heat transfer thermostats.• Electronic temperature sensor.• FAN5555 is included in HeatTrans systems.

VENTILATION FAN CATALOGUE€¦ · 150mm (Axial) vs 150mm (Centrifugal) fan. The starting point is...

Documents

Transcript of VENTILATION FAN CATALOGUE€¦ · 150mm (Axial) vs 150mm (Centrifugal) fan. The starting point is...