SUPREME - bidetsPLUS Bidet BB 1000...plumbing installation work has been completed. Never operate...
Transcript of SUPREME - bidetsPLUS Bidet BB 1000...plumbing installation work has been completed. Never operate...
SUPREME BIDET SEAT
Thank you for purchasing BIO BIDET(Supreme Bidet Seat).This unit is manufactured for household use.
MAINTENANCE
WATER DRAINING
TROUBLE SHOOTING
SPECIFICATIONS
INFORMATION TO THE USER
WARRANTY
OPERATION (BASIC)
OPERATION (DETAILS)
INSTALLATION
DETACHMENT
IMPORTANT SAFEGUARDS /
GENERAL CAUTIONS
CAUTIONS BEFORE INSTALLATION
IDENTIFICATION
PREPARATIO
NO
PERATION
INSTA
LLATION
MA
INTEN
AN
CE
Contents
4
6
8
9
10
14
17
19
18
20
21
22
22
3Installation Manual and Operating Instructions
4
The following terms are used in this manual to indicate hazards of varying degrees of severity
indicates potentially hazardous situation which, if not avoided, may result in minoror moderate injury or in damage to the product or other property.
indicates potentially hazardous situation which, if not avoided, could result in death orserious injury.WARNING
indicates an imminently hazardous situation which, if not avoided, will result in deathor serious injury.DANGER
CAUTION
Do not touch the power cord with wet hands. Do not reachfor a product that has fallen into water. Unplug immediately!
Do not open the product to repair or remodel.Only qualified service personnel should service BIO BIDET(SUPREME BIDET SEAT). Do not use attachments notrecommended by the manufacturer.
IMPORTANT SAFEGUARDS/GENERAL CAUTIONS1
Do not splash water on BIO BIDET(SUPREME BIDET SEAT). Do not install in a location exposed to excessive moisturethat condensation forms on the BIO BIDET(SUPREME BIDETSEAT) surface. To avoid damage to electronic componentsdue to high levels of humidity, provide adequate ventilationopening via an opened window and/or door when bathing.
The BIO BIDET(SUPREME BIDET SEAT) must be grounded.Connect the grounding wire properly to the groundingterminal. Refer to the grounding instructions. An approvedGround Fault Circuit Interrupt (GFCI) must be used.
PLEASE OBSERVE THE FOLLOWING PRECAUTION BEFORE USING BIO BIDET(SUPREME BIDETSEAT)
PREPARATIO
N
READ ALL INSTRUCTIONS BEFORE INSTALLATION AND USE
DANGER - To reduce the risk of electrocution
WARNING - To reduce the risk of burns, electrocution, fire, or injury to persons
Installation Manual and Operating Instructions
5
Please disconnect the power cord when you clean the BIOBIDET(SUPREME BIDET SEAT) or detach it from toilet bowl.Do not supply electrical power to the unit until theplumbing installation work has been completed.
Never operate this product if it has a damaged cord or plug.BIO BIDET(SUPREME BIDET SEAT) must be connected to astandard voltage power source. Do not connect power cordif the cord is damaged or broken. Do not plug the unit intoa loose electric outlet.
Keep the cord away from heated surfaces. And keep anyflammable materials away from the BIO BIDET(SUPREMEBIDET SEAT)
About Low Temperature Burns-A burn occurs when the skin has been exposed to high temperatures. However, alow temperature burn may occur when the skin has been in contact with anobject at relatively low temperature (about 104
oF ).
Close supervision is necessary when this product is used by, on, or near children orinvalids
Connect the BIO BIDET(SUPREME BIDET SEAT) to cold watersupply pipe carrying potable water. Do not connect to anindustrial water supply line that does not carry water ofdrinking quality.This will negatively effect hygiene and performance.
Do not plug in the power cord before connecting thewater supply hose.
SHOWER TOILET SEAT
If using any chemical toilet bowl cleaner, be sure to wipe upany spills that splash onto BIO BIDET(SUPREME BIDET SEAT).Do not use benzene or any acid chemical detergent. Onlyneutral detergent permitted.
PREPARATIO
N
Installation Manual and Operating Instructions
6
CAUTIONS BEFORE INSTALLATION2
- SAVE THESE INSTRUCTIONS -
CAUTION
Drain the water from BIO BIDET(SUPREME BIDET SEAT)and unplug the power if it is not going to be used foran extended period of time. This will help prevent theunit from freezing over and in good condition.
Never operate this product if itis not working properly, if it hasbeen dropped or damaged, ordropped into water. Return theproduct to a service center forexamination and repair
Do not strain or push the connected hose and tubeconnecter; it may cause water leakage. Never drop orinsert any object into any opening or hose
Do not obstruct orput anything into thedry air outlet. Do notapply excessive forceto the shower nozzle.
PREPARATIO
NPREPA
RATION
Do not stand or siton the seat coverlid.It is not designed tosupport a user’sbody weight.
Do not bang theseat and lid.
Use BIO BIDET(SUPREME BIDETSEAT) only as described in theoperating instructions. Neveruse while sleeping or drowsy.Do not use while bathing.
Be careful so thatBIO BIDET(SUPREMEBIDET SEAT) doesnot become stainedwith excrement andurine.
BIO BIDET(SUPREME BIDET SEAT) MUST BE PLUGGED into a regular voltage (North America120V AC, 60Hz / Europe 230V AC, 50Hz) and the rated power consumption is 660W / 660WGrounded GFCI outlet. In locations where only a standard two-prong outlet is available, it is theresponsibility of the user to install a grounded three-prong outlet.Using a higher voltage is dangerous and may result in a fire or other accident. BIO BIDET is notresponsible for damage resulting from the use of BIO BIDET(SUPREME BIDET SEAT) on otherthan specified voltage, or operating it without proper grounding.
WIRING REQUIREMENT
Installation Manual and Operating Instructions
7
GROUND INSTRUCTIONS
(1) BIO BIDET(SUPREME BIDET SEAT) has a three-prong grounding plug, which must beplugged into an outlet that is properly installed and grounded. In the event of anelectrical short circuit, grounding reduces the risk of electric shock by providing an escapewire for the electric current.If repair or replacement of the cord or plug is necessary, do not connect the groundingwire to either flat blade terminal. The wire with insulation having an outer surface that isgreen with or without yellow stripes is the grounding wire.Check with a qualified electrician or serviceman if the grounding instructions are notcompletely understood, or if in doubt as to whether the product is properly grounded.
The use of an extension cord is not recommended or advised. If it is necessary to use an extension cord,use only a three-prong extension cord, and a three slot built-in GFCI receptacle that will accept the plugon BIO BIDET(SUPREME BIDET SEAT). The marked rating of the extension cord should be equal to orgreater than the electrical rating of the unit (10amp). Consult a qualified electrician or service person ifyou are not sure whether the unit is properly grounded.
BIO BIDET(SUPREME BIDET SEAT) must be on a separated circuit.No other appliance should share the circuit with BIOBIDET(SUPREME BIDET SEAT). Sharing a circuit could cause thebranch circuit fuse to blow or the circuit breaker to trip. Continuoususage under these conditions could result in fire or propertydamage.
WARNING
IMPROPER GROUNDING CAN RESULT IN A RISK OF ELECTRICSHOCK.Electric wiring has to be done in accordance with all local codes,or in the absence of local codes, with the National ElectricalCodes.
DANGER
PREPARATIO
N
GROUNDING PINGROUNDEDOUTLET BOX
ADAPTER ADAPTER
METAL SCREWTAB forGrounding Screw
GROUNDEDOUTLET
- Figure 1-
(2) This product is for use on a nominal 120V circuit, and has a grounding plug that looks likethe plug illustrated in sketch A in Figure 1. A temporary adapter, which looks like theadapter illustrated in sketches B and C, may be used to connect this plug to a 2-polereceptacle as shown in sketch B if a properly grounded outlet is not available. Thetemporary adapter should be used only until a properly grounded outlet (sketch A) can beinstalled by a qualified electrician. The green colored rigid ear, lug, or the like extendingfrom the adapter must be connected to a permanent ground such as a properly groundedoutlet box cover. Whenever the adapter is used, it must be held in place by the screw.
Installation Manual and Operating Instructions
SHOWER TOILET SEAT
MAIN UNIT1
ACCESSORIES2
8
IDENTIFICATION3
Washer (2 pcs)
Cone Packing (2 pcs)
Mounting Bolts 2 pcs
Quick Release plate(1 pc)
Nuts (2 pcs)
Bolt Guide(2 pcs)
Spanner
Water Supply Tube to Toilet Fresh Tank
Water Supply Tube to BIO BIDET(Shower Toilet Seat)
T-Valve and Washer
Enema Function Nozzle
Feminine Wash Nozzle
Posterior Wash Nozzle
Enema Function Nozzle
Feminine Wash Nozzle
Posterior Wash Nozzle
Dryer Outlet
Simple Operation Panel
Digital Occupied Sensor
Drain / Unit SeparationButton
Operation LED Window
Heated Seat
Lid
Warning Lable (Caution Lable)
Deodorizer
Deodorizer Filter Unit (Use Semipermanent)
DEODORANT (CARBONATE)
Simple GuideSheet
Remotecontrol
Remotecontrol FixedPanel
Fix screw &Blocking (3pcs)
Battery (2pcs)1.5V AA
InstallationInstructionSheet
UserOperatingManual
PREPARATIO
N
3/8” Spare Nut(With Packing)
Installation Manual and Operating Instructions
9
OPERATION (BASIC)4
• When you sit on the unit, please sit down on the central position in order toactivate the sensor.
• After an extended wash, allow about three minutes for water to reheat.
Adjust the oscillation functionand nozzle position (5 levels).
Adjust the water pressureand warm air dryertemperature.
Power Saving mode button.
Adjust the water and seattemperature (4 levels).
OPERATIO
N
Installation Manual and Operating Instructions
Stop
Posterior Wash
Feminine Wash
Simple Operation Panel
SHOWER TOILET SEAT
SERVICE / INQUIRY : 877-339-5214
10
OPERATION (DETAILS)5
SIT DOWN ON THE SEAT• When you sit down on the seat, the LED lamp on the control panel will light up.• When the digital sensor on the seat is activated, the operation LED window on the
unit will light “Occupied sensor”; simultaneously, Deodorizer will start working.
• Open the shut off valve and check for any water leaks.• Plug the unit into the proper power source and turn it on. • The water tank will be filled after pushing a “Wash” ( or ) button. When the
water tank is filled, the buzzer sounds ”Beep”.
CLEANSING • CLEANSING 1. (Posterior Wash) - Press “Posterior Wash”( ), automatically nozzle comes out and sprays warm water to posterior. If
you press “Oscillation (Move)”, the nozzle moves back and forth automatically. Nozzle stops moving
when the switch is pressed again. It automatically stops after two minutes.
• CLEANSING 2. (Enema Wash) STEP 1 : Press “Enema Wash”( ), automatically nozzle comes out and sprays.
STEP 2 : The stream of water is set to the posterior center.
STEP 3 : Press “water pressure-High & Low button”( , ) and adjust the water pressure.
STEP 4 : If you feel that the water has filled you up a bit, just wait for a minute and push the water and
feces out.
- If you do not push out the water in a rectum completely, you may feel unwell.
• CLEANSING 3. (Feminine Wash)- Press “Feminine Wash”( ), automatically nozzle comes out and sprays warm water to feminine
area. If you press “Oscillation (Move)”, the nozzle moves back and forth automatically. Nozzle stops
moving when the switch is pressed again and It automatically stops after two minutes.
PREPARATION1
OPERATION2
STOP• Press this switch to stop in middle of operation.
OPERATIO
N
Installation Manual and Operating Instructions
11
WATER PRESSURE ADJUSTMENT AND DRY TEMPERATURE ADJUSTMENT• After sitting down on the seat, the LED lamp( ) for water pressure should
light at 3 levels( ). You can adjust the water pressure with “High( )” and“Low( )” button. Adjust the “Warm Air Dryer” temperature with “High( )” and“Low( )” button. In addition, the unit memorizes the air temperature of prior use.Basically, the uint memorizes the water pressure level of prior use. (But, when userput the simple operation panel, the first water pressure always should be fixed onmiddle level)
STOP• Press this button to stop in middle of operation.
WARM AIR DRYER • Press “Dry( )”, dry air comes out. Middle of operation, you can adjust the warm
air temperature with “High( )” and “Low( )” button. It will automatically stopabout 3 minutes later.
Room temperature approx. 93.2o
F (34o
C) 98.6o
F (37o
C) 104o
F (40o
C)
SEAT TEMPERATURE
WARM WATER TEMPERATURE AND SEAT TEMPERATURE ADJUSTMENT• The temperature of water and seat are adjustable to the desired level by pressing
‘WATER( )’ and ‘SEAT( )’ button.
WATER TEMPERATURE
Room temperature approx. 93.2o
F (34o
C) 98.6o
F (37o
C) 105.8o
F (41o
C)
OPERATIO
N
Installation Manual and Operating Instructions
When user does not use remote control for 10 seconds, the LED lampwill turned off in order to save the battery power.CAUTION
SHOWER TOILET SEAT
12
OPERATION (DETAILS)5
DEODORIZER
OSCILLATION ( Nozzle Move Function)
• The deodorizer is activated when the unit is occupied. After using the unit, itwill automatically stop about 1 minute later.
• The deodorized air velocity of wind is adjustable to the desired level bypressing “STOP”( ) and “WATER”( ), simultaneously.
• When using Posterior or Feminine Washing, press in a “OSCILLATION (Move)”button will provide oscillating spray for much wider cleansing. This functionis not available during Enema Wash.
• In addition, the oscillation can be adjusted to the desired position by pressing“OSCILLATION (Move)” and “( )(Front) or ( ) (Rear)”, simultaneously.
• If you push “OSCILLATION (MOVE)” again, the oscillation will be stopautomatically.
* Auto-Setting of Oscillation: Without being occupied, press “OSCILLATION (MOVE)” button for 3 seconds to set up “Auto-
Setting of Oscillation”.
* Auto-Setting of Oscillation: Without pushing “Move” button, when using Posterior or Feminine Washing, this oscillation
function will be operated automatically.
1Level
OFFDeodorizer
(Air velocity ofwind)
On Using __> Low Speed
After using __>Low Speed
Deodorizer(Air velocity of
wind)On Using __>Low Speed
After using __>High Speed
Deodorizer(Air velocity of
wind)On Using __>High Speed
After using __>High Speed
2Level 3Level 4Level+
(Level1~4)
NOZZLE POSITION ADJUSTMENT• Nozzle position is adjustable to the desired position by pressing “(Front) ( )”
or “(Rear) ( )” button from 1 to 5 positions. After using product, the nozzleshould return to position 3.
OPERATIO
N
Installation Manual and Operating Instructions
14
INSTALLATION6
STEPS
Shut off the water supply to theexisting toilet tank by closing theangle stop valve. Drain the toilet tankcompletely. Remove the water supplyhose to toilet tank.
CAUTION BEFORE INSTALLATION• Please, do not plug in before installation.• If you need an electric power system or extension, please consult a qualified
electrician.
Flexible Tube
Flexible Tube
3/8” Spare Nut
1 Removing the existing seat and lid.• By using a wrench (spanner) or other proper
tool, release the nut on both sides of existingtoilet to remove the toilet seat and lid.
2
Connect T-Valve.• Remove existing supply tube from fresh tank • Angle Stop Valve is standard 1/2” in size. If it
is 3/8”use the 1/2”to 3/8”conversion nut kitswith packing before connecting the AngleStop valve. Install T-Valve on top of AngleStop Valve.
3 One of flexible tube connects fromtop of T-Valve to toilet tank.
4IN
STALLATIO
N
Use the Spanner
Use the Spanner Use the Spanner
Installation Manual and Operating Instructions
13
MASSAGE (Rhythmic Wash)
ECONOMY (Power Save Mode)
NOZZLE CLEANING (Automatic)
• When using Posterior Wash, Enema Wash or Feminine Washing, pressing"MASSAGE (Rhythmic Wash)" button will provide pulsating spray. In addition, thewater pressure is adjustable by pushing "( ) High or ( ) Low" and "MASSAGE",simultaneously.
* Auto-Setting of Massage: Without being occupied, press “MASSAGE” button for 3 seconds to set up Auto-Setting of
“MASSAGE”.
* Auto-Setting of MASSAGE: Without pushing “MASSAGE” button, when using CLEANSING, this Massage function will be
operated automatically.
• BIO BIDET(SUPREME BIDET SEAT) has an automatic nozzle self-cleaningfunction that works before and after each operation.
NOZZLE CLEANING (Manual)• Nozzle can be cleaned manually by pressing “CLEANSING 1: Posterior Wash( )”
button for 3 seconds without being occupied on the seat and nozzle will come out.Press “CLEANSING 1: Posterior Wash( )” button for 3 seconds again to returnnozzle to stand- by mode.
• ECONOMY 1: The “ECONOMY 1” feature drops the water temperature andseat temperature to about 32
o
C (90o
F) when the seat is not in use.
• ECONOMY 2: The “ECONOMY 2” (Intelligent Economy Function) records themain time the family use it, for 4 days after installation. Then the unit sets upthe “Power-On and Off Time”. The “ECONOMY 2” feature drops the water andseat temperature to about 32oC (90oF). When the seat is in use during thismode, the settings are returned to their original levels. After using, the unit isreturned to “ECONOMY Mode”.
OPERATIO
N
Installation Manual and Operating Instructions
SHOWER TOILET SEAT
15
Cone PackingWasherNut
Cone PackingWasherNut
Bolt
Quick-Release Plate Bolt Guide
Place bolt guide with bolt in quick-release plate and slide into designatedgroove at rear bottom of main body.
5 Place main unit aligning to toiletseat mounting holes.
6
Securly tightening mounting boltswith supplied cone packing andplastic washer.
7 Connect water supply flexible hose tothe unit.
8
INSTA
LLATION
* Connect ground wire from T-Valve to BIO BIDET(SUPREME BIDET SEAT).* Check for any water leakage.
Use the Spanner
Installation Manual and Operating Instructions
SHOWER TOILET SEAT
16
INSTALLATION6
Insert the deodorant catalyst into the unit.
How to change the deodorant catalyst
Peel off adhesive protection to use self-adhesive.Place supplied batteries and close the cover.
Or, mount on the wall using supplied screws.
Screw mounting holes.
Deodorant.Deodorant case
Cover
9
Installation of Remote Control.10
Check the deodorant package.1
Follow the below photos to change the deodorant.2
Insert the new deodorant case into the unit.3
INSTA
LLATION
Installation Manual and Operating Instructions
17
INSTA
LLATION
Disconnect power.1
Shut off water supply.2
Empty water tank using drainage. 3Slide out main unit from quick release plate while pushing drainage as illustrated below.4
Disconnect the tube and T-Valve from unit (Refer to page # 14).5
If you move or clean the toilet, please separate the BIO BIDET(SUPREME BIDET SEAT) from toilet bowl.
Do not turn upside down.
DETACHMENT7
Installation Manual and Operating Instructions
SHOWER TOILET SEAT
CLEANING THE BODY OF UNIT• When you clean the body, do not use “thinner”, “benzene” or “NaClO”. It causes defects to
the surface of unit.• Please use a wet cloth when you clean the unit.• Do not spray water directly on the unit.• When you clean the unit, please disconnect the power plug.
CLEANING THE STRAINER
18
MAINTENANCE8
CLEANING THE NOZZLE
• When the “Posterior Wash( )” button(in simple operationpanel) is pressed for 3 second without occupying the seat,the nozzle can be cleaned with a toothbrush.
• After cleaning the nozzle, push the “Stop( )” button(in simple operation panel) once again, and the nozzleretracts itself.
The product {BIO BIDET(SUPREME BIDET SEAT)} will not operate properly if the strainer isclogged. Please clean the strainer regularly.
1) Close the shut off valve.
3) Unscrew the water filter nut.
5) Re-screw the water filter nut.
2) Flush the toilet to empty the water reservoir.
4) Clean the strainer with a small brush or water.
6) Open the shut off valve.
MA
INTEN
AN
CE
Installation Manual and Operating Instructions
19
WATER DRAINING9M
AIN
TENA
NCE
MAINTENANCE FOR WINTER SEASON
Please check the power cord whether plugged in or not.1Keep the water temperature on “Middle or High Level” to prevent water fromfreezing.2
If you do not use the unit for long time, please disconnect the power plug anddrain the water.
3
If you do not use the product for long time, please drain water from the warm water tank.
1) Disconnect the power plug.
2) Close the shut off valve.
3) Press the drain lever until the water is completely drained from the unit’s water tank.
4) To re-supply water after draining, open the shut off valve.
Do not drink the drained water.Do not insert finger into the drain hole.Before draining, unplug the power cord and wait 30 minutes until the unit has cooled down.
DRAIN THE WARM WATER TANK IN THE UNIT
Installation Manual and Operating Instructions
SHOWER TOILET SEAT
20
TROUBLE SHOOTING10
Cause RemedyTrouble
1.The water tank is not filled.
2.The shutoff valve is closed.
3. Freezing inside the main unit or
the water supply pipe.
1.Disconnected the power cord.
2.The seat is not occupied.
3. The battery of remote controller
is exhausted.
1.Check the water supply system
1.The water pressure level is set to
“LOW”.
2.The strainer is clogged.
1.The water temperature is set to
“LOW”.
2.Continuous operation has
depleted the supply of warm
water.
1.The seat & dryer temperature is
set to “LOW”
1. Wait about one minute.
2.Press the desired washing
button once again.
3.Turn on the shutoff valve to
open.
4.Heat the room (for about two
hours). Operating the unit while
parts are frozen will cause a
malfunction.
1.Connect the power cord.
2. Check the power supply
system in your house.
3.Occupy the seat (The unit has
an occupied sensor).
4.Replace the battery.
1. If water is leaking from the
main unit, call the service center
or the place you purchased.
1.Set the water pressure to
“HIGH”.
2.Clean the strainer.
1.Set the water temperature to
“HIGH”
2. Wait about three minutes.
1. Set the seat & dryer
temperature to “HIGH”.
The washing wateris not sprayed
The unit is notoperating
Water is leaking
The washing waterpressure is weak
The washing wateris not warm
The seat and dryeris not warm
MA
INTEN
AN
CE
Installation Manual and Operating Instructions
Feminine Wash
WashDevice
Heated Seat
WarmAir DryerDevice
SPECIFICATIONS11
Posterior Wash
Water PressureAdjustable
Warm WaterTemperature
Heater
Safety Devices
Temperature
Heater
Safety Device
Adjustable Dry Temperature
(Room Temp~45 oC)
Deodorizer
Enema Function
Remote control
Inlet water temperature 3oC ~ 35o
C (37.4 oF ~ 95 o
F )
3oC ~ 40o
C (37.4 oF ~ 104o
F )
W : 475mm (18.7 inch) L : 525mm (20.6 inch) H : 185mm (7.28 inch)
W : 475mm (18.7 inch) L : 493mm (19.4 inch) H : 185mm (7.28 inch)
Ambient Temperature
Dimension
Weight (kg, lbs)
Heater
(250W)
Safety Device
(Themal fuse, bimetal)
Power Rating
Power cord
TypeWater inlettype Water inlet pressure
BB-1000Specifications
AC 120V 60Hz 660W
Direct Inlet flow type
0.4 ~ 7.5 kgf/cm2(5.69 psi ~ 106.7psi)
1.2m (4 feet)
Max. 1.2ℓ/min ( Max. 0.32 GPM)
Max. 1.2ℓ/min ( Max. 0.32 GPM)
5 Levels
Room Temp - 40oC (Room Temp. 104
oF )
600 W
Thermal fuse, Thermal switch, Float switch
Room Temp ~ 41oC (Room Temp. ~ 105.8
oF )
55W
Thermal fuse
Installation Manual and Operating Instructions 21
MA
INTEN
AN
CE
5.2kg(10.7 lbs)
SHOWER TOILET SEAT
Elongated Round
22
WARRANTY 13UCI, Inc.
Limited Warranty
MA
INTEN
AN
CE
This limited warranty gives you specific legal rights, and you may also have other rights
that may vary from state to state or according to other conditions.
General Limited Warranty Covered The Manufacturer, UCI, Inc will warrant to the
original retail buyer only, which fails in normal use and within the applicable periods
specified below, following the terms of this warranty. UCI, Inc replacement will be
warranted to the original purchaser of the products.
The Parts Warranty If the parts fail within Twelve (12) months after original installation
following the installation manual and normal operation, UCI, Inc will furnish a
replacement part(s).
INFORMATION TO THE USER12This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one more of the followingmeasures:
- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.
Installation Manual and Operating Instructions
WARNINGChanges or modifications not expressly approved by the manufacturer could void the user'sauthority to operate the equipment.• OR“Note : The manufacturer is not responsible for any Radio or TV interference caused byunauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.”
23
Serial Number #
Purchaser
Dealer(Company)
To ensure your warranty protection you must complete and return this card toUCI, Inc within 10 days after date of purchase.
Model
company
Address
City
Phone
Address
Fax
Country
Dealer Code
PLACE
STAP
HERE
Service
Department
Head office: 205 Berg StreetAlgonquin, Illinois 60102Tel: (847) 854-7292 Fax: (847) 854-1296
WARRANTY REGISTRATION
MA
INTEN
AN
CE
1. Defects and/or malfunctions from failure to properly install, operate and/or maintain the unitin accordance with the installation manual.
2. Damage from abuse, fire, flood, freeze, and any other act of God.3. Damage resulting from unauthorized alterations, attachments and/or repairs.4. If the product was not installed properly to residential water closets.5. Damage from installing the unit in an environment with animals, mice or insects.6. Damage caused by excess moisture or from water clogging the water closet.7. Damage from not being installed in accordance with all applicable local codes, ordinances
and good trade practices.8. Color fading due to use in wrong environments.9. Damage from consumable chemicals.
10. The warranty will not be covered without providing the date of purchase with originalreceipts.
11. Damage from misuse due to not following the installation manual.
Will be not Covered by this Warranty
Installation Manual and Operating Instructions
SHOWER TOILET SEAT