Structural Dynamics of Linear Elastic Single-Degree-of...
Transcript of Structural Dynamics of Linear Elastic Single-Degree-of...
FEMA 451B Topic 3 Notes Slide 1
SDOF Dynamics 3 - 1Instructional Material Complementing FEMA 451, Design Examples
Structural Dynamics ofLinear Elastic Single-Degree-of-Freedom
(SDOF) Systems
This set of slides covers the fundamental concepts of structural dynamics of linear elastic single-degree-of-freedom (SDOF) structures. A separate topic covers the analysis of linear elastic multiple-degree-of-freedom (MDOF) systems. A separate topic also addresses inelastic behavior of structures. Proficiency in earthquake engineering requires a thorough understanding of each of these topics.
FEMA 451B Topic 3 Notes Slide 2
SDOF Dynamics 3 - 2Instructional Material Complementing FEMA 451, Design Examples
Structural Dynamics
• Equations of motion for SDOF structures
• Structural frequency and period of vibration
• Behavior under dynamic load
• Dynamic magnification and resonance
• Effect of damping on behavior
• Linear elastic response spectra
This slide lists the scope of the present topic. In a sense, the majority of the material in the topic provides background on the very important subject of response spectra.
FEMA 451B Topic 3 Notes Slide 3
SDOF Dynamics 3 - 3Instructional Material Complementing FEMA 451, Design Examples
Importance in Relation to ASCE 7-05• Ground motion maps provide ground
accelerations in terms of response spectrumcoordinates.
• Equivalent lateral force procedure gives base shear in terms of design spectrum and period of vibration.
• Response spectrum is based on 5% critical damping in system.
• Modal superposition analysis uses design response spectrum as basic ground motion input.
The relevance of the current topic to the ASCE 7-05 document is provided here. Detailed referencing to numbered sections in ASCE 7-05 is provided in many of the slides. Note that ASCE 7-05 is directly based on the 2003 NEHRP Recommended Provisions for Seismic Regulations for New Buildings and Other Structures, FEMA 450, which is available at no charge from the FEMA Publications Center, 1-800-480-2520 (order by FEMA publication number).
FEMA 451B Topic 3 Notes Slide 4
SDOF Dynamics 3 - 4Instructional Material Complementing FEMA 451, Design Examples
Idealized SDOF Structure
Mass
Stiffness
Damping
F t u t( ), ( )
t
F(t)
t
u(t)
The simple frame is idealized as a SDOF mass-spring-dashpot model with a time-varying applied load. The function u(t) defines the displacement response of the system under the loading F(t). The properties of the structure can be completely defined by the mass, damping, and stiffness as shown. The idealization assumes that all of the mass of the structure can be lumped into a single point and that all of the deformation in the frame occurs in the columns with the beam staying rigid. Represent damping as a simple viscous dashpot common as it allows for a linear dynamic analysis. Other types of damping models (e.g., friction damping) are more realistic but require nonlinear analysis.
FEMA 451B Topic 3 Notes Slide 5
SDOF Dynamics 3 - 5Instructional Material Complementing FEMA 451, Design Examples
F t( )f tI ( )
f tD ( )0 5. ( )f tS0 5. ( )f tS
F t f t f t f tI D S( ) ( ) ( ) ( )− − − = 0
f t f t f t F tI D S( ) ( ) ( ) ( )+ + =
Equation of Dynamic Equilibrium
Here the equations of motion are shown as a force-balance. At any point in time, the inertial, damping, and elastic resisting forces do not necessarily act in the same direction. However, at each point in time, dynamic equilibrium must be maintained.
FEMA 451B Topic 3 Notes Slide 6
SDOF Dynamics 3 - 6Instructional Material Complementing FEMA 451, Design Examples
-40
0
40
0.00 0.20 0.40 0.60 0.80 1.00
-0.50
0.00
0.50
0.00 0.20 0.40 0.60 0.80 1.00
-15.00
0.00
15.00
0.00 0.20 0.40 0.60 0.80 1.00
-400.00
0.00
400.00
0.00 0.20 0.40 0.60 0.80 1.00
Acceleration, in/sec2
Velocity, in/sec
Displacement, in
Applied Force, kips
Observed Response of Linear SDOF
Time, sec
This slide (from NONLIN) shows a series of response histories for a SDOF system subjected to a saw-tooth loading. As a result of the loading, the mass will undergo displacement, velocity, and acceleration. Each of these quantities are measured with respect to the fixed base of the structure.Note that although the loading is discontinuous, the response is relatively smooth. Also, the vertical lines show that velocity is zero when displacement is maximum and acceleration is zero when velocity is maximum.NONLIN is an educational program for dynamic analysis of simple linear and nonlinear structures. Version 7 is included on the CD containing these instructional materials.
FEMA 451B Topic 3 Notes Slide 7
SDOF Dynamics 3 - 7Instructional Material Complementing FEMA 451, Design Examples
Observed Response of Linear SDOF(Development of Equilibrium Equation)
-30.00
-15.00
0.00
15.00
30.00
-0.60 -0.30 0.00 0.30 0.60
Displacement, inches
-4.00
-2.00
0.00
2.00
4.00
-20.00 -10.00 0.00 10.00 20.00
Velocity, In/sec
-50.00
-25.00
0.00
25.00
50.00
-500 -250 0 250 500
Acceleration, in/sec2
Spring Force, kips Damping Force, Kips Inertial Force, kips
Slope = k= 50 kip/in
Slope = c= 0.254 kip-sec/in
Slope = m= 0.130 kip-sec2/in
f t k u tS ( ) ( )= f t c u tD ( ) &( )= f t m u tI ( ) &&( )=
These X-Y curves are taken from the same analysis that produced the response histories of the previous slide. For a linear system, the resisting forces are proportional to the motion. The slope of the inertial-force vs acceleration curve is equal to the mass. Similar relationships exist for damping force vs velocity (slope = damping) and elastic force vsdisplacement (slope = stiffness).The importance of understanding and correct use of units cannot be over emphasized.
FEMA 451B Topic 3 Notes Slide 8
SDOF Dynamics 3 - 8Instructional Material Complementing FEMA 451, Design Examples
F t( )f tI ( )
f tD ( )0 5. ( )f tS0 5. ( )f tS
m u t c u t k u t F t&&( ) & ( ) ( ) ( )+ + =
Equation of Dynamic Equilibrium
f t f t f t F tI D S( ) ( ) ( ) ( )+ + =
Here the equations of motion are shown in terms of the displacement, velocity, acceleration, and force relationships presented in the previous slide. Given the forcing function, F(t), the goal is to determine the response history of the system.
FEMA 451B Topic 3 Notes Slide 9
SDOF Dynamics 3 - 9Instructional Material Complementing FEMA 451, Design Examples
Mass
• Includes all dead weight of structure• May include some live load• Has units of force/acceleration
Inte
rnal
For
ce
Acceleration
1.0M
Properties of Structural Mass
Mass is always assumed constant throughout the response. Section 12.7.2 of ASCE 7-05 defines this mass in terms of the “effective weight” of the structure. The effective weight includes 25% of the floor live load in areas used for storage, 10 psf partition allowance, operating weight of all permanent equipment, and 20% of the flat roof snow load when that load exceeds 30 psf.
FEMA 451B Topic 3 Notes Slide 10
SDOF Dynamics 3 - 10Instructional Material Complementing FEMA 451, Design Examples
Damping
• In absence of dampers, is called inherent damping• Usually represented by linear viscous dashpot• Has units of force/velocity
Dam
ping
For
ce
Velocity
1.0C
Properties of Structural Damping
Except for the case of added damping, real structures do not have discrete dampers as shown. Real or inherent damping arises from friction in the material. For cracked concrete structures, damping is higher because of the rubbing together of jagged surfaces on either side of a crack.In analysis, we use an equivalent viscous damper primarily because of the mathematical convenience. (Damping force is proportional to velocity.)
FEMA 451B Topic 3 Notes Slide 11
SDOF Dynamics 3 - 11Instructional Material Complementing FEMA 451, Design Examples
Damping
Dam
ping
For
ce
Displacement
Properties of Structural Damping (2)
Damping vs displacement response iselliptical for linear viscous damper.
AREA =ENERGYDISSIPATED
The force-displacement relationship for a linear viscous damper is an ellipse. The area within the ellipse is the energy dissipated by the damper. The greater the energy dissipated by damping, the lower the potential for damage in structures. This is the primary motivation for the use of added damping systems. Energy that is dissipated is irrecoverable.
FEMA 451B Topic 3 Notes Slide 12
SDOF Dynamics 3 - 12Instructional Material Complementing FEMA 451, Design Examples
• Includes all structural members• May include some “seismically nonstructural” members• Requires careful mathematical modelling• Has units of force/displacement
Sprin
g Fo
rce
Displacement
1.0K
Properties of Structural Stiffness
Stif
fnes
s
In this topic, it is assumed that the force-displacement relationship in the spring is linear elastic. Real structures, especially those designed according to current seismic code provisions, will not remain elastic and, hence, the force-deformation relationship is not linear. However, linear analysis is often (almost exclusively) used in practice. This apparent contradiction will be explained as this discussion progresses.The modeling of the structure for stiffness has very significant uncertainties. Section 12.7.3 of ASCE 7-05 provides some guidelines for modeling the structure for stiffness.
FEMA 451B Topic 3 Notes Slide 13
SDOF Dynamics 3 - 13Instructional Material Complementing FEMA 451, Design Examples
• Is almost always nonlinear in real seismic response• Nonlinearity is implicitly handled by codes• Explicit modelling of nonlinear effects is possible
Sprin
g Fo
rce
Displacement
Properties of Structural Stiffness (2)
Stif
fnes
s
AREA =ENERGYDISSIPATED
This is an idealized response of a simple inelastic structure. The area within the curve is the inelastic hysteretic energy dissipated by the yielding material. The larger hysteretic energy in relation to the damping energy, the greater the damage.In this topic, it is assumed that the material does not yield. Nonlinear inelastic response is explicitly included in a separate topic.
FEMA 451B Topic 3 Notes Slide 14
SDOF Dynamics 3 - 14Instructional Material Complementing FEMA 451, Design Examples
Undamped Free Vibration
)cos()sin()( 00 tututu ωω
ω+=
&
m u t k u t&&( ) ( )+ = 0Equation of motion:
0u&Initial conditions:
ω0uA&
= B u= 0Solution: ω =km
Assume: u t A t B t( ) sin( ) cos( )= +ω ω
0u
In this unit, we work through a hierarchy of increasingly difficult problems. The simplest problem to solve is undamped free vibration. Usually, this type of response is invoked by imposing a static displacement and then releasing the structure with zero initial velocity. The equation of motion is a second order differential equation with constant coefficients. The displacement term is treated as the primary unknown.The assumed response is in terms of a sine wave and a cosine wave. It is easy to see that the cosine wave would be generated by imposing an initial displacement on the structure and then releasing. The sine wave would be imposed by initially “shoving” the structure with an initial velocity. The computed solution is a combination of the two effects.The quantity ω is the circular frequency of free vibration of the structure (radians/sec). The higher the stiffness relative to mass, the higher the frequency. The higher the mass with respect to stiffness, the lower the frequency.
FEMA 451B Topic 3 Notes Slide 15
SDOF Dynamics 3 - 15Instructional Material Complementing FEMA 451, Design Examples
ω =km
f =ωπ2
Tf
= =1 2π
ω
Period of Vibration(sec/cycle)
Cyclic Frequency(cycles/sec, Hertz)
Circular Frequency (radians/sec)
Undamped Free Vibration (2)
-3-2-10123
0.0 0.5 1.0 1.5 2.0
Time, seconds
Dis
plac
emen
t, in
ches
T = 0.5 sec
u0
&u01.0
This slide shows a computed response history for a system with an initial displacement and velocity. Note that the slope of the initial response curve is equal to the initial velocity (v = du/dt). If this term is zero, the free vibration response is a simple cosine wave. Note also that the undamped motion shown will continue forever if uninhibited. In real structures, damping will eventually reduce the free vibration response to zero.The relationship between circular frequency, cyclic frequency, and period of vibration is emphasized. The period of vibration is probably the easiest to visualize and is therefore used in the development of seismic code provisions. The higher the mass relative to stiffness, the longer the period of vibration. The higher the stiffness relative to mass, the lower the period of vibration.
FEMA 451B Topic 3 Notes Slide 16
SDOF Dynamics 3 - 16Instructional Material Complementing FEMA 451, Design Examples
Approximate Periods of Vibration(ASCE 7-05)
xnta hCT =
NTa
1.0=
Ct = 0.028, x = 0.8 for steel moment framesCt = 0.016, x = 0.9 for concrete moment framesCt = 0.030, x = 0.75 for eccentrically braced framesCt = 0.020, x = 0.75 for all other systems
Note: This applies ONLY to building structures!
For moment frames < 12 stories in height, minimumstory height of 10 feet. N = number of stories.
One of the first tasks in any seismic design project is to estimate the period of vibration of the structure. For preliminary design (and often for final design), an empirical period of vibration is used. Section 12.8.2 of ASCE 7-05 provides equations for estimating the period. These equations are listed here.
FEMA 451B Topic 3 Notes Slide 17
SDOF Dynamics 3 - 17Instructional Material Complementing FEMA 451, Design Examples
Empirical Data for Determinationof Approximate Period for Steel Moment Frames
8.0028.0 na hT =
Ta is based on curve-fitting of data obtained from measured response of California buildings after small earthquakes. As will be seen later, the smaller the period, the larger the earthquake force that must be designed for. Hence, a lower bound empirical relationship is used. Because the empirical period formula is based on measured response of buildings, it should not be used to estimate the period for other types of structure (bridges, dams, towers).
FEMA 451B Topic 3 Notes Slide 18
SDOF Dynamics 3 - 18Instructional Material Complementing FEMA 451, Design Examples
Periods of Vibration of Common Structures
20-story moment resisting frame T = 1.9 sec10-story moment resisting frame T = 1.1 sec1-story moment resisting frame T = 0.15 sec
20-story braced frame T = 1.3 sec10-story braced frame T = 0.8 sec1-story braced frame T = 0.1 sec
Gravity dam T = 0.2 secSuspension bridge T = 20 sec
This slide shows typical periods of vibration for several simple structures. Engineers should develop a “feel” for what an appropriate period of vibration is for simple building structures.For building structures, the formula T = 0.1 in is the simplest “reality check.”The period for a 10-story building should be approximately 1 sec. If a computer analysis gives a period of 0.2 sec or 3.0 sec for a 10-story building, something is probably amiss in the analysis.
FEMA 451B Topic 3 Notes Slide 19
SDOF Dynamics 3 - 19Instructional Material Complementing FEMA 451, Design Examples
SD1 Cu> 0.40g 1.4
0.30g 1.40.20g 1.50.15g 1.6< 0.1g 1.7
computedua TCTT ≤=
Adjustment Factor on Approximate Period(Table 12.8-1 of ASCE 7-05)
Applicable ONLY if Tcomputed comes from a “properlysubstantiated analysis.”
In some cases, it is appropriate to remove the “conservatism” from the empirical period formulas. This is done through use of the Cu coefficient. This conservatism arises from two sources:
1. The lower bound period was used in the development of the periodformula.
2. This lower bound period is about 1/1.4 times the best-fit period. The empirical formula was developed on the basis of data from California
buildings. Buildings in other parts of the country (e.g., Chicago) where seismic forces are not so high will likely be larger than those for the same building in California.
It is important to note that the larger period cannot be used without the benefit of a “properly substantiated” analysis, which is likely performed on a computer.
FEMA 451B Topic 3 Notes Slide 20
SDOF Dynamics 3 - 20Instructional Material Complementing FEMA 451, Design Examples
If you do not have a “more accurate” period (from a computer analysis), you must use T = Ta.
If you have a more accurate period from a computeranalysis (call this Tc), then:
if Tc > CuTa use T = CuTa
if Ta < Tc < TuCa use T = Tc
if Tc < Ta use T = Ta
Which Period of Vibration to Usein ELF Analysis?
This slide shows the limitations on the use of CuTa. ASCE-7-05 will not allow the use of a period larger than CuTa regardless of what the computer analysis says. Similarly, the NEHRP Recommended Provisions does not require that you use a period less than Ta.
FEMA 451B Topic 3 Notes Slide 21
SDOF Dynamics 3 - 21Instructional Material Complementing FEMA 451, Design Examples
Damped Free Vibration
u t e u t u u ttD
DD( ) cos( )
&sin( )= +
+⎡
⎣⎢
⎤
⎦⎥
−ξω ω ξωω
ω00 0
m u t c u t k u t&&( ) &( ) ( )+ + = 0Equation of motion:
u u0 0&Initial conditions:
Solution:
Assume: u t e st( ) =
ξω
= =c
mccc2 ω ω ξD = −1 2
This slide shows the equation of motion and the response in damped free vibration. Note the similarity with the undamped solution. In particular, note the exponential decay term that serves as a multiplier on the whole response.Critical damping (cc) is defined as the amount of damping that will produce no oscillation. See next slide.The damped circular frequency is computed as shown. Note that in many practical cases (x < 0.10), it will be effectively the same as the undampedfrequency. The exception is very highly damped systems. Note that the damping ratio is often given in terms of % critical.
FEMA 451B Topic 3 Notes Slide 22
SDOF Dynamics 3 - 22Instructional Material Complementing FEMA 451, Design Examples
ξω
= =c
mccc2
Damping in Structures
cc is the critical damping constant.
Time, sec
Displacement, in
ξ is expressed as a ratio (0.0 < ξ < 1.0) in computations.
Sometimes ξ is expressed as a% (0 < ξ < 100%).
Response of Critically Damped System, ξ=1.0 or 100% critical
The concept of critical damping is defined here. A good example of a critically damped response can be found in heavy doors that are fitted with dampers to keep the door from slamming when closing.
FEMA 451B Topic 3 Notes Slide 23
SDOF Dynamics 3 - 23Instructional Material Complementing FEMA 451, Design Examples
-30.00
-15.00
0.00
15.00
30.00
-0.60 -0.30 0.00 0.30 0.60
Displacement, inches
-4.00
-2.00
0.00
2.00
4.00
-20.00 -10.00 0.00 10.00 20.00
Velocity, In/sec
-50.00
-25.00
0.00
25.00
50.00
-500 -250 0 250 500
Acceleration, in/sec2
Spring Force, kips Damping Force, Kips Inertial Force, kips
True damping in structures is NOT viscous. However, for lowdamping values, viscous damping allows for linear equations and vastly simplifies the solution.
Damping in Structures
An earlier slide is repeated here to emphasize that damping in real structures is NOT viscous. It is frictional or hysteretic. Viscous damping is used simply because it linearizes the equations of motion. Use of viscous damping is acceptable for the modeling of inherent damping but should be used with extreme caution when representing added damping or energy loss associated with yielding in the primary structural system.
FEMA 451B Topic 3 Notes Slide 24
SDOF Dynamics 3 - 24Instructional Material Complementing FEMA 451, Design Examples
Damped Free Vibration (2)
-3-2-10123
0.0 0.5 1.0 1.5 2.0
Time, seconds
Dis
plac
emen
t, in
ches
0% Damping10% Damping20% Damping
This slide shows some simple damped free vibration responses. When the damping is zero, the vibration goes on forever. When the damping is 20% critical, very few cycles are required for the free vibration to be effectively damped out. For 10% damping, peak is approximately ½ of the amplitude of the previous peak.
FEMA 451B Topic 3 Notes Slide 25
SDOF Dynamics 3 - 25Instructional Material Complementing FEMA 451, Design Examples
Damping in Structures (2)Welded steel frame ξ = 0.010Bolted steel frame ξ = 0.020
Uncracked prestressed concrete ξ = 0.015Uncracked reinforced concrete ξ = 0.020Cracked reinforced concrete ξ = 0.035
Glued plywood shear wall ξ = 0.100Nailed plywood shear wall ξ = 0.150
Damaged steel structure ξ = 0.050Damaged concrete structure ξ = 0.075
Structure with added damping ξ = 0.250
Some realistic damping values are listed for structures comprised of different materials. The values for undamaged steel and concrete (upper five lines of table) may be considered as working stress values.
FEMA 451B Topic 3 Notes Slide 26
SDOF Dynamics 3 - 26Instructional Material Complementing FEMA 451, Design Examples
Inherent damping
Added damping
ξ is a structural (material) propertyindependent of mass and stiffness
critical%0.7to5.0=Inherentξ
ξ is a structural property dependent onmass and stiffness anddamping constant C of device
critical%30to10=Addedξ
Damping in Structures (3)
C
The distinction between inherent damping and added damping should be clearly understood.
FEMA 451B Topic 3 Notes Slide 27
SDOF Dynamics 3 - 27Instructional Material Complementing FEMA 451, Design Examples
ln uu
1
22
21
=−
πξξ
ξπ
≅−u uu
1 2
22
For alldamping values
For very lowdamping values
Measuring Damping from Free Vibration Test
-1
-0.5
0
0.5
1
0.00 0.50 1.00 1.50 2.00 2.50 3.00Time, Seconds
Ampl
itude
u e t0
−ξω
u1
u2 u3
One of the simplest methods to measure damping is a free vibration test. The structure is subjected to an initial displacement and is suddenly released. Damping is determined from the formulas given. The second formula should be used only when the damping is expect to be less than about 10% critical.
FEMA 451B Topic 3 Notes Slide 28
SDOF Dynamics 3 - 28Instructional Material Complementing FEMA 451, Design Examples
Undamped Harmonic Loading
)sin()()( 0 tptuktum ω=+&&Equation of motion:
-150-100
-500
50100150
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
Time, Seconds
Forc
e, K
ips
po=100 kips= 0.25 sec
= frequency of the forcing function
ωπ2
=T
ω
T
The next series of slides covers the response of undamped SDOF systems to simple harmonic loading. Note that the loading frequency is given by the omega term with the overbar. The loading period is designated in a similar fashion.
FEMA 451B Topic 3 Notes Slide 29
SDOF Dynamics 3 - 29Instructional Material Complementing FEMA 451, Design Examples
Solution:
Particular solution: Complimentary solution:
u t C t( ) s in ( )= ω
u t A t B t( ) sin( ) cos( )= +ω ω
⎟⎠⎞
⎜⎝⎛ −
−= )sin()sin(
)/(11)( 2
0 ttkptu ω
ωωω
ωω
Undamped Harmonic Loading (2)
m u t k u t p t&&( ) ( ) s in ( )+ = 0 ωEquation of motion:
Assume system is initially at rest:
This slide sets up the equation of motion for undamped harmonic loading and gives the solution. We have assumed the system is initially at rest.
FEMA 451B Topic 3 Notes Slide 30
SDOF Dynamics 3 - 30Instructional Material Complementing FEMA 451, Design Examples
Define β ωω
=
( )u t pk
t t( ) sin( ) sin( )=−
−02
11 β
ω β ω
Static displacementSteady state
response(at loading frequency)
Transient response(at structure’s frequency)
Loading frequency
Structure’s natural frequency
Undamped Harmonic Loading
Dynamic magnifier
Here we break up the response into the steady state response (at the frequency of loading) and the transient response (at the structure’s own natural frequency). Note that the term po/k is the “static” displacement. The dynamic magnifier shows how the dynamic effects may increase (or decrease) the response. This magnifier is a function of the frequency ratio β. Note that the magnifier goes to infinity if the frequency ratio β is 1.0. This defines the resonant condition.In other words, the response is equal to the static response, times a multiplier, times the sum of two sine waves, one in phase with the load and the other in phase with the structure’s undamped natural frequency.
FEMA 451B Topic 3 Notes Slide 31
SDOF Dynamics 3 - 31Instructional Material Complementing FEMA 451, Design Examples
-10-505
10
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-10-505
10
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-10-505
10
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
Time, seconds
spac
ee
t,
-200-100
0100200
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
ω π= 2 rad / secω π= 4 rad / sec uS = 5 0. .inβ = 0 5.
Loading (kips)
Steady stateresponse (in.)
Transientresponse (in.)
Total response(in.)
This is a time-history response of a structure with a natural frequency of 4 rad/sec (f = 2 Hz, T = 0.5 sec), and a loading frequency of 2 rad/sec (f = 1 Hz, T = 1 sec), giving a frequency ratio β of 0.5. The harmonic load amplitude is 100 kips. The static displacement is 5.0 inches. Note how the steady state response is at the frequency of loading, is in phase with the loading, and has an amplitude greater than the static displacement. The transient response is at the structure’s own frequency. In real structures, damping would cause this component to disappear after a few cycles of vibration.
FEMA 451B Topic 3 Notes Slide 32
SDOF Dynamics 3 - 32Instructional Material Complementing FEMA 451, Design Examples
Steady stateresponse (in.)
Transientresponse (in.)
Total response(in.)
Loading (kips)
ω π= 4 rad / secω π≈ 4 rad / sec uS = 5 0. .inβ = 0 99.
-500
-250
0
250
500
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-150-100
-500
50100150
0 .00 0 .25 0 .50 0 .75 1.00 1 .25 1.50 1 .75 2 .00
-500
-250
0
250
500
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-80
-40
0
40
80
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
Time, seconds
p,
In this slide, ϖ has been increased to 4π rad/sec, and the structure is almost at resonance. The steady state response is still in phase with the loading,but note the huge magnification in response. The transient response is practically equal to and opposite the steady state response. The total response increases with time.If one looks casually at the steady state and transient response curves, it appears that they should cancel out. Note, however, that the two responses are not exactly in phase due to the slight difference in the loading and natural frequencies. This can be seen most clearly at the time 1.75 sec into the response. The steady state response crosses the horizontal axis to the right of the vertical 1.75 sec line while the transient response crosses exactly at 1.75 sec.In real structures, the observed increased amplitude could occur only to some limit and then yielding would occur. This yielding would introduce hysteretic energy dissipation (apparent damping), causing the transient response to disappear and leading to a constant, damped, steady state response.
FEMA 451B Topic 3 Notes Slide 33
SDOF Dynamics 3 - 33Instructional Material Complementing FEMA 451, Design Examples
-80
-40
0
40
80
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
Time, seconds
Dis
plac
emen
t, in
.
2π uS
Undamped Resonant Response Curve
Linear envelope
This is an enlarged view of the total response curve from the previous slide. Note that the response is bounded within a linear increasing envelope with the increase in displacement per cycle being 2π times the static displacement.
FEMA 451B Topic 3 Notes Slide 34
SDOF Dynamics 3 - 34Instructional Material Complementing FEMA 451, Design Examples
Steady stateresponse (in.)
Transientresponse (in.)
Total response (in.)
Loading (kips)
ω π= 4 rad / secω π≈ 4 rad / sec uS = 5 0. .inβ = 1 01.
-150-100
-500
50100150
0 .00 0 .25 0 .50 0 .75 1.00 1.25 1.50 1.75 2 .00
-500
-250
0
250
500
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-50 0
-25 0
0
25 0
50 0
0 .00 0 .25 0 .5 0 0 .75 1 .00 1 .2 5 1 .50 1 .75 2 .0 0
-80
-40
0
40
80
0.00 0.25 0 .50 0 .75 1.00 1 .25 1 .50 1.75 2 .00
T im e, seconds
p,
In this slide, the loading frequency has been slightly increased, but the structure is still nearly at resonance. Note, however, that the steady state response is 180 degrees out of phase with the loading and the transient response is in phase. The resulting total displacement is effectively identical to that shown two slides back.
FEMA 451B Topic 3 Notes Slide 35
SDOF Dynamics 3 - 35Instructional Material Complementing FEMA 451, Design Examples
Steady state response (in.)
Transient response (in.)
Total response (in.)
Loading (kips)
ω π=8 rad / secω π= 4 rad / sec uS = 5 0. .inβ = 2 0.
-150-100
-500
50100150
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-6
-3
0
3
6
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-6
-3
0
3
6
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
-6
-3
0
3
6
0 .00 0 .25 0 .50 0 .75 1 .00 1 .25 1 .50 1 .75 2 .00
T im e, seconds
p,
The loading frequency is now twice the structure’s frequency. The important point here is that the steady state response amplitude is now less than the static displacement.
FEMA 451B Topic 3 Notes Slide 36
SDOF Dynamics 3 - 36Instructional Material Complementing FEMA 451, Design Examples
-12.00
-8.00
-4.00
0.00
4.00
8.00
12.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00
Frequency Ratio β
Mag
nific
atio
n Fa
ctor
1/(1
- β2 ) In phase
180 degrees out of phase
Resonance
Response Ratio: Steady State to Static(Signs Retained)
This plot shows the ratio of the steady state response to the static displacement for the structure loaded at different frequencies. At low loading frequencies, the ratio is 1.0, indicating a nearly static response (as expected). At very high frequency loading, the structure effectively does not have time to respond to the loading so the displacement is small and approaches zero at very high frequency. The resonance phenomena is very clearly shown. The change in sign at resonance is associated with the in-phase/out-of-phase behavior that occurs through resonance.
FEMA 451B Topic 3 Notes Slide 37
SDOF Dynamics 3 - 37Instructional Material Complementing FEMA 451, Design Examples
0.00
2.00
4.00
6.00
8.00
10.00
12.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00
Frequency Ratio β
Mag
nific
atio
n Fa
ctor
1/(1
- β2 )
Response Ratio: Steady State to Static(Absolute Values)
Resonance
Slowlyloaded
1.00
Rapidlyloaded
This is the same as the previous slide but absolute values are plotted. This clearly shows the resonance phenomena.
FEMA 451B Topic 3 Notes Slide 38
SDOF Dynamics 3 - 38Instructional Material Complementing FEMA 451, Design Examples
Damped Harmonic Loading
m u t cu t k u t p t&&( ) &( ) ( ) sin( )+ + = 0 ωEquation of motion:
-150-100-50
050
100150
0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
Time, Seconds
Forc
e, K
ips
po=100 kips
sec25.02==
ωπT
We now introduce damping into the behavior. Note the addition of the appropriate term in the equation of motion.
FEMA 451B Topic 3 Notes Slide 39
SDOF Dynamics 3 - 39Instructional Material Complementing FEMA 451, Design Examples
Solution:
Assume system is initially at rest
Particular solution:
Complimentary solution:
u t C t D t( ) sin( ) cos( )= +ω ω
[ ]u t e A t B ttD D( ) sin( ) cos( )= +−ξω ω ω
Damped Harmonic LoadingEquation of motion:
m u t cu t k u t p t&&( ) &( ) ( ) sin( )+ + = 0 ω
ω ω ξD = −1 2
ξω
=c
m2
[ ]u t e A t B ttD D( ) sin( ) cos( )= +− ξω ω ω
+ +C t D tsin( ) cos( )ω ω
This slide shows how the solution to the differential equation is obtained. The transient response (as indicated by the A and B coefficients) will damp out and is excluded from further discussion.
FEMA 451B Topic 3 Notes Slide 40
SDOF Dynamics 3 - 40Instructional Material Complementing FEMA 451, Design Examples
Transient response at structure’s frequency(eventually damps out)
Steady state response,at loading frequency
D pk
o=−
− +2
1 22 2 2
ξββ ξβ( ) ( )
Damped Harmonic Loading
C pk
o=−
− +1
1 2
2
2 2 2
ββ ξβ( ) ( )
)cos()sin( tDtC ωω +
+[ ]u t e A t B ttD D( ) sin( ) cos( )= +− ξω ω ω
This slide shows the C and D coefficients of the steady state response. Note that there is a component in phase with the loading (the sine term) and a component out of phase with the loading (the cosine term). The actual phase difference between the loading and the response depends on the damping and frequency ratios.Note the exponential decay term causes the transient response to damp out in time.
FEMA 451B Topic 3 Notes Slide 41
SDOF Dynamics 3 - 41Instructional Material Complementing FEMA 451, Design Examples
-50
-40
-30
-20
-10
0
10
20
30
40
50
0.00 1.00 2.00 3.00 4.00 5.00
Time, Seconds
Dis
plac
emen
t Am
plitu
de, I
nche
s
BETA=1 (Resonance)Beta=0.5Beta=2.0
Damped Harmonic Loading (5% Damping)
This plot shows the response of a structure at three different loading frequencies. Of significant interest is the resonant response, which is now limited. (The undamped response increases indefinitely.)
FEMA 451B Topic 3 Notes Slide 42
SDOF Dynamics 3 - 42Instructional Material Complementing FEMA 451, Design Examples
Staticδξ21
-50
-40
-30
-20
-10
0
10
20
30
40
50
0.00 1.00 2.00 3.00 4.00 5.00
Time, Seconds
Dis
plac
emen
t Am
plitu
de, I
nche
s
Damped Harmonic Loading (5% Damping)
For viscously damped structures, the resonance amplitude will always be limited as shown.
FEMA 451B Topic 3 Notes Slide 43
SDOF Dynamics 3 - 43Instructional Material Complementing FEMA 451, Design Examples
Harmonic Loading at ResonanceEffects of Damping
-200
-150
-100
-50
0
50
100
150
200
0.00 1.00 2.00 3.00 4.00 5.00
Time, Seconds
Dis
plac
emen
t Am
plitu
de, I
nche
s
0% Damping %5 Damping
A comparison of damped and undamped responses is shown here. The undamped response has a linear increasing envelope; the damped curve will reach a constant steady state response after a few cycles.
FEMA 451B Topic 3 Notes Slide 44
SDOF Dynamics 3 - 44Instructional Material Complementing FEMA 451, Design Examples
0.00
2.00
4.00
6.00
8.00
10.00
12.00
14.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00
Frequency Ratio, β
Dyn
amic
Res
pons
e A
mpl
ifier
0.0% Damping5.0 % Damping10.0% Damping25.0 % Damping
RD =− +
11 22 2 2( ) ( )β ξβ
Resonance
Slowlyloaded Rapidly
loaded
This plot shows the dynamic magnification for various damping ratios. For increased damping, the resonant response decreases significantly. Note that for slowly loaded structures, the dynamic amplification is 1.0 (effectively static). For high frequency loading, the magnifier is zero.Note also that damping is most effective at or near resonance (0.5 < β < 2.0).
FEMA 451B Topic 3 Notes Slide 45
SDOF Dynamics 3 - 45Instructional Material Complementing FEMA 451, Design Examples
Summary Regarding Viscous Dampingin Harmonically Loaded Systems
• For systems loaded at a frequency near their natural frequency, the dynamic response exceeds the static response. This is referred to as dynamic amplification.
• An undamped system, loaded at resonance, will have an unbounded increase in displacement over time.
A summary of some of the previous points is provided.
FEMA 451B Topic 3 Notes Slide 46
SDOF Dynamics 3 - 46Instructional Material Complementing FEMA 451, Design Examples
Summary Regarding Viscous Dampingin Harmonically Loaded Systems
• Damping is an effective means for dissipating energy in the system. Unlike strain energy, which is recoverable, dissipated energy is not recoverable.
• A damped system, loaded at resonance, will have a limited displacement over time with the limit being (1/2ξ) times the static displacement.
• Damping is most effective for systems loaded at or near resonance.
Summary continued.
FEMA 451B Topic 3 Notes Slide 47
SDOF Dynamics 3 - 47Instructional Material Complementing FEMA 451, Design Examples
LOADING YIELDING
UNLOADING UNLOADED
F F
F
u
F
u
u u
EnergyStored
EnergyDissipated
EnergyRecovered
TotalEnergyDissipated
CONCEPT of ENERGY STOREDand Energy DISSIPATED
12
1
3
2
4
3
It is very important that the distinction between stored energy and dissipated energy be made clear. (Note that some texts use the term “absorbed”energy in lieu of stored energy.) In the first diagram, the system remains elastic and all of the strain energy is stored. If the bar were released, all of the energy would be recovered.In the second diagram, the applied deformation is greater than the elastic deformation and, hence, the system yields. The energy shown in green is stored, but the energy shown in red is dissipated. If the bar is unloaded, the stored energy is recovered, but the dissipated energy is lost. This is shown in Diagrams 3 and 4.
FEMA 451B Topic 3 Notes Slide 48
SDOF Dynamics 3 - 48Instructional Material Complementing FEMA 451, Design Examples
Time, T
F(t)
General Dynamic Loading
The discussion will now proceed to general dynamic loading. By general loading, it is meant that no simple mathematical function defines the entire loading history.
FEMA 451B Topic 3 Notes Slide 49
SDOF Dynamics 3 - 49Instructional Material Complementing FEMA 451, Design Examples
General Dynamic Loading Solution Techniques
• Fourier transform
• Duhamel integration
• Piecewise exact
• Newmark techniques
All techniques are carried out numerically.
There are a variety of ways to solve the general loading problem and all are carried out numerically on the computer. The Fourier transform and Duhamel integral approaches are not particularly efficient (or easy to explain) and, hence, these are not covered here. Any text on structural dynamics will provide the required details.The piecewise exact method is used primarily in the analysis of linear systems. The Newmark method is useful for both linear and nonlinear systems. Only the basic principles underlying of each of these approaches are presented.
FEMA 451B Topic 3 Notes Slide 50
SDOF Dynamics 3 - 50Instructional Material Complementing FEMA 451, Design Examples
dt
( ) odFF Fdt
τ τ= +
dF
dt
τ
Piecewise Exact Method
Fo
In the piecewise exact method, the loading function is broken into a number of straight-line segments. In a sense, the name of the method is a misnomerbecause the method is not exact when the actual loading is smooth (like a sine wave) because the straight line load segments are only an approximation of the actual load. When the actual load is smooth, the accuracy of the method depends on the level of discretization when defining the loading function.For earthquake loads, the load is almost always represented by a recorded accelerogram, which does consist of straight line segments. (There would be little use in trying to interpolate the ground motion with smooth curves.) Hence, for the earthquake problem, the piecewise exact method is truly exact.
FEMA 451B Topic 3 Notes Slide 51
SDOF Dynamics 3 - 51Instructional Material Complementing FEMA 451, Design Examples
Initial conditions 00, =ou 00, =ou&
Determine “exact” solution for 1st time step
)(1 τuu = )(1 τuu && = )(1 τuu &&&& =
)(1, τuuo = )(1,0 τuu && =Establish new initial conditions
Obtain exact solution for next time step
)(2 τuu = )(2 τuu && = )(2 τuu &&&& =
LOOP
Piecewise Exact Method
The basic idea of the piecewise exact method is to develop a solution for a straight line loading segment knowing the initial conditions. Given the initial conditions and the load segment, the solution at the end of the load step is determined and this is then used as the initial condition for the next step of the analysis. The analysis then proceeds step by step until all load segments have been processed.
FEMA 451B Topic 3 Notes Slide 52
SDOF Dynamics 3 - 52Instructional Material Complementing FEMA 451, Design Examples
Piecewise Exact Method
Advantages:
• Exact if load increment is linear• Very computationally efficient
Disadvantages:
• Not generally applicable for inelastic behavior
Note: NONLIN uses the piecewise exact method forresponse spectrum calculations.
It should be noted that the piecewise exact method may be used for nonlinear analysis in certain circumstances. For example, the “fast nonlinear analysis” (FNA) method developed by Ed Wilson and used in SAP 2000 utilizes the piecewise exact method. In FNA, the nonlinearities are “right-hand sided,” leaving only linear terms in the left-hand side of the equations of motion.
FEMA 451B Topic 3 Notes Slide 53
SDOF Dynamics 3 - 53Instructional Material Complementing FEMA 451, Design Examples
Newmark Techniques
• Proposed by Nathan Newmark• General method that encompasses a family of different
integration schemes• Derived by:
– Development of incremental equations of motion– Assuming acceleration response over short time step
The Newmark method is one of the most popular methods for solving the general dynamic loading problem. It is applicable to both linear and nonlinear systems. It is equally applicable to both SDOF and MDOF systems.The Newmark method is described in more detail in the topic on inelastic behavior of structures.
FEMA 451B Topic 3 Notes Slide 54
SDOF Dynamics 3 - 54Instructional Material Complementing FEMA 451, Design Examples
Newmark MethodAdvantages:
• Works for inelastic response
Disadvantages:
• Potential numerical error
Note: NONLIN uses the Newmark method forgeneral response history calculations
The advantages and disadvantages of the Newmark method are listed. The principal advantage is that the method may be applied to inelastic systems. The method also may be used (without decoupling) for multiple-degree-of-freedom systems.
FEMA 451B Topic 3 Notes Slide 55
SDOF Dynamics 3 - 55Instructional Material Complementing FEMA 451, Design Examples
-0.40
-0.20
0.00
0.20
0.40
0.00 1.00 2.00 3.00 4.00 5.00 6.00
TIME, SECONDS
GR
OU
ND
AC
C, g
Development of Effective Earthquake Force
In an earthquake, no actual force is applied to the building. Instead, the ground moves back and forth (and up and down) and this movement induces inertial forces that then deform the structure. It is the displacements in the structure, relative to the moving base, that impose deformations on the structure. Through the elastic properties, these deformations cause elastic forces to develop in the individual members and connections.
FEMA 451B Topic 3 Notes Slide 56
SDOF Dynamics 3 - 56Instructional Material Complementing FEMA 451, Design Examples
Earthquake Ground Motion, 1940 El Centro
Many ground motions now are available via the Internet.
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0 10 20 30 40 50 60
Time (sec)
Gro
und
Acce
lera
tion
(g's)
-30
-20
-10
0
10
20
30
40
0 10 20 30 40 50 60
Time (sec)
Gro
und
Vel
ocity
(cm
/sec
)-15
-10
-5
0
5
10
15
0 10 20 30 40 50 60
Time (sec)
Gro
und
Dis
plac
emen
t (cm
)
Earthquake ground motions usually are imposed through the use of the ground acceleration record or accelerogram. Some programs (like Abaqus) may require instead that the ground displacement records be used as input.
FEMA 451B Topic 3 Notes Slide 57
SDOF Dynamics 3 - 57Instructional Material Complementing FEMA 451, Design Examples
m u t u t c u t k u tg r r r[&& ( ) && ( )] & ( ) ( )+ + + = 0
mu t c u t k u t mu tr r r g&& ( ) & ( ) ( ) && ( )+ + = −
Development of Effective Earthquake Force
-0.40
-0.20
0.00
0.20
0.40
0.00 1.00 2.00 3.00 4.00 5.00 6.00
TIME, SECONDS
GR
OU
ND
AC
C, g
Ground Acceleration Response History
gu&& tu&&ru&&
In this slide, it is assumed that the ground acceleration record is used as input. The total acceleration at the center of mass is equal to the ground acceleration plus the acceleration of the center of mass relative to the moving base. The inertial force developed at the center of mass is equal to the mass times the total acceleration. The damping force in the system is a function of the velocity of the top of the structure relative to the moving base. Similarly, the spring force is a function of the displacement at the top of the structure relative to the moving base. The equilibrium equation with the zero on the response history spectrum (RHS) represents the state of the system at any point in time. The zero on the RHS reflects the fact that there is no applied load.If that part of the total inertial force due to the ground acceleration is moved to the right-hand side (the lower equation), all of the forces on the left-hand side are in terms of the relative acceleration, velocity, and displacement. This equation is essentially the same as that for an applied load (see Slide 8) but the “effective earthquake force” is simply the negative of the mass times the ground acceleration. The equation is then solved for the response history of the relative displacement.
FEMA 451B Topic 3 Notes Slide 58
SDOF Dynamics 3 - 58Instructional Material Complementing FEMA 451, Design Examples
)()()()( tumtuktuctum grrr &&&&& −=++
)()()()( tutumktu
mctu grrr &&&&& −=++
ξω2=mc 2ω=
mk
Divide through by m:
Make substitutions:
“Simplified” form of Equation of Motion:
)()()(2)( 2 tutututu grrr &&&&& −=++ ωξωSimplified form:
In preparation for the development of response spectra, it is convenient to simplify the equation of motion by dividing through by the mass. When the substitutions are made as indicated, it may be seen that the response is uniquely defined by the damping ratio, the undamped circular frequency of vibration, and the ground acceleration record.
FEMA 451B Topic 3 Notes Slide 59
SDOF Dynamics 3 - 59Instructional Material Complementing FEMA 451, Design Examples
)()()(2)( 2 tutututu grrr &&&&& −=++ ωξω
Ground motion acceleration history
Structural frequency
Damping ratio
For a given ground motion, the response history ur(t) is function of the structure’s frequency ω and damping ratio ξ.
This restates the point made in the previous slide. A response spectrum is created for a particular ground motion and for a structure with a constant level of damping. The spectrum is obtained by repeatedly solving the equilibrium equations for structures with varying frequencies of vibration and then plotting the peak displacement obtained for that frequency versus the frequency for which the displacement was obtained.
FEMA 451B Topic 3 Notes Slide 60
SDOF Dynamics 3 - 60Instructional Material Complementing FEMA 451, Design Examples
Change in ground motion or structural parameters ξand ω requires re-calculation of structural response
Response to Ground Motion (1940 El Centro)
-6
-4
-2
0
2
4
6
0 10 20 30 40 50 60
Time (sec)
Stru
ctur
al D
ispl
acem
ent (
in)
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0 10 20 30 40 50 60
Time (sec)
Gro
und
Acce
lera
tion
(g's
)
Excitation applied to structure with given ξ and ω
Peak displacement
Computed response
SOLVER
The next several slides treat the development of the 5% damped response spectrum for the 1940 El Centro ground motion record. The “solver”indicated in the slide is a routine, such as the Newmark method, that takes the ground motion record, the damping ratio, and the system frequency as input and reports as output only the maximum absolute value of the relative displacement that occurred over the duration of the ground motion. It is important to note that by taking the absolute value, the sign of the peak response is lost. The time at which the peak response occurred is also lost (simply because it is not recorded).
FEMA 451B Topic 3 Notes Slide 61
SDOF Dynamics 3 - 61Instructional Material Complementing FEMA 451, Design Examples
0
4
8
12
16
0 2 4 6 8 10
PERIOD, Seconds
DIS
PLA
CEM
ENT,
inch
es
The Elastic Displacement Response SpectrumAn elastic displacement response spectrum is a plotof the peak computed relative displacement, ur, for anelastic structure with a constant damping ξ, a varyingfundamental frequency ω (or period T = 2π/ ω), respondingto a given ground motion.
5% damped response spectrum for structureresponding to 1940 El Centro ground motion
This slide is a restatement of the previous point.
FEMA 451B Topic 3 Notes Slide 62
SDOF Dynamics 3 - 62Instructional Material Complementing FEMA 451, Design Examples
-0.08
-0.06
-0.04
-0.02
0.00
0.02
0.04
0.06
0.08
0 1 2 3 4 5 6 7 8 9 10 11 12
Time, Seconds
Dis
plac
emen
t, In
ches
ξ = 0.05T = 0.10 secUmax= 0.0543 in.
0.00
2.00
4.00
6.00
8.00
10.00
0.00 0.50 1.00 1.50 2.00
Period, Seconds
Dis
plac
emen
t, In
ches
Computation of Response Spectrum for El Centro Ground Motion
Elastic response spectrum
Computed response
Here, the first point in the response spectrum is computed. For this and all subsequent steps, the ground motion record is the same and the damping ratio is set as 5% critical. Only the frequency of vibration, represented by period T, is changed.When T = 0.10 sec (circular frequency = 62.8 radians/sec), the peak computed relative displacement was 0.0543 inches. The response history from which the peak was obtained is shown at the top of the slide. This peak occurred at about 5 sec into the response, but this time is not recorded. Note the high frequency content of the response. The first point on the displacement response spectrum is simply the displacement (0.0543 inches) plotted against the structural period (0.1 sec) for which the displacement was obtained.
FEMA 451B Topic 3 Notes Slide 63
SDOF Dynamics 3 - 63Instructional Material Complementing FEMA 451, Design Examples
ξ = 0.05T = 0.20 secUmax = 0.254 in.
-0.40
-0.30
-0.20
-0.10
0.00
0.10
0.20
0.30
0.40
0 1 2 3 4 5 6 7 8 9 10 11 12
Time, Seconds
Dis
plac
emen
t, In
ches
0.00
2.00
4.00
6.00
8.00
10.00
0.00 0.50 1.00 1.50 2.00
Period, Seconds
Dis
plac
emen
t, In
ches
Computation of Response Spectrumfor El Centro Ground Motion
Elastic response spectrum
Computed response
Here the whole procedure is repeated, but the system period is changed to 0.2 sec. The computed displacement history is shown at the top of the slide, which shows that the peak displacement was 0.254 inches. This peak occurred at about 2.5 sec into the response but, as before, this time is not recorded. Note that the response history is somewhat smoother than that in the previous slide.The second point on the response spectrum is the peak displacement (0.254 inch) plotted against the system period, which was 0.2 sec.
FEMA 451B Topic 3 Notes Slide 64
SDOF Dynamics 3 - 64Instructional Material Complementing FEMA 451, Design Examples
ξ = 0.05T = 0.30 secUmax = 0.622 in.
-0.80
-0.60
-0.40
-0.20
0.00
0.20
0.40
0.60
0.80
0 1 2 3 4 5 6 7 8 9 10 11 12
Time, Seconds
Dis
plac
emen
t, In
ches
0.00
2.00
4.00
6.00
8.00
10.00
0.00 0.50 1.00 1.50 2.00
Period, Seconds
Dis
plac
emen
t, In
ches
Computation of Response Spectrumfor El Centro Ground Motion
Elastic response spectrum
Computed response
The third point on the response spectrum is the peak displacement (0.622 inch) plotted against the system period, which was 0.3 sec. Again, the response is somewhat “smoother” than before.
FEMA 451B Topic 3 Notes Slide 65
SDOF Dynamics 3 - 65Instructional Material Complementing FEMA 451, Design Examples
ξ = 0.05T = 0.40 secUmax = 0.956 in.
-1.20
-0.90
-0.60
-0.30
0.00
0.30
0.60
0.90
1.20
0 1 2 3 4 5 6 7 8 9 10 11 12
Time, Seconds
Dis
plac
emen
t, In
ches
0.00
2.00
4.00
6.00
8.00
10.00
0.00 0.50 1.00 1.50 2.00
Period, Seconds
Dis
plac
emen
t, In
ches
Computation of Response Spectrumfor El Centro Ground Motion
Elastic response spectrum
Computed response
The fourth point on the response spectrum is the peak displacement (0.956 inch) plotted against the system period, which was 0.40 sec.
FEMA 451B Topic 3 Notes Slide 66
SDOF Dynamics 3 - 66Instructional Material Complementing FEMA 451, Design Examples
ξ = 0.05T = 0.50 secUmax = 2.02 in.
-2.40
-1.80
-1.20
-0.60
0.00
0.60
1.20
1.80
2.40
0 1 2 3 4 5 6 7 8 9 10 11 12
Time, Seconds
Dis
plac
emen
t, In
ches
0.00
2.00
4.00
6.00
8.00
10.00
0.00 0.50 1.00 1.50 2.00
Period, Seconds
Dis
plac
emen
t, In
ches
Computation of Response Spectrumfor El Centro Ground Motion
Elastic response spectrum
Computed response
The next point on the response spectrum is the peak displacement (2.02 inches) plotted against the system period, which was 0.50 sec.
FEMA 451B Topic 3 Notes Slide 67
SDOF Dynamics 3 - 67Instructional Material Complementing FEMA 451, Design Examples
ξ = 0.05T = 0.60 secUmax= -3.00 in.
Computation of Response Spectrumfor El Centro Ground Motion
-3.20-2.40-1.60-0.800.000.801.602.403.20
0 1 2 3 4 5 6 7 8 9 10 11 12
Time, Seconds
Dis
plac
emen
t, In
ches
0.00
2.00
4.00
6.00
8.00
10.00
0.00 0.50 1.00 1.50 2.00
Period, Seconds
Dis
plac
emen
t, In
ches
Elastic response spectrum
Computed response
The next point on the response spectrum is the peak displacement (3.03 inches) plotted against the system period, which was 0.60 sec. Note that only the absolute value of the displacement is recorded. The complete spectrum is obtained by repeating the process for all remaining periods in the range of 0.7 through 2.0 sec. For this response spectrum, 2/0.1 or 20 individual points are calculated, requiring 20 full response history analyses. A real response spectrum would likely be run at a period resolution of about 0.01 sec, requiring 200 response history analyses.
FEMA 451B Topic 3 Notes Slide 68
SDOF Dynamics 3 - 68Instructional Material Complementing FEMA 451, Design Examples
Complete 5% Damped Elastic DisplacementResponse Spectrum for El Centro
Ground Motion
0.00
2.00
4.00
6.00
8.00
10.00
12.00
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0Period, Seconds
Dis
plac
emen
t, In
ches
This is the full 5% damped elastic displacement response spectrum for the 1940 El Centro ground motion. Note that the spectrum was run for periods up to 4.0 sec. This spectrum was generated using NONLIN.Note also that the displacement is nearly zero when T is near zero. This is expected because the relative displacement of a very stiff structure (with Tnear zero) should be very small. The displacement then generally increases with period, although this trend is not consistent. The reductions in displacement at certain periods indicate that the ground motion has little energy at these periods. As shown later, a different earthquake will have an entirely different response spectrum.
FEMA 451B Topic 3 Notes Slide 69
SDOF Dynamics 3 - 69Instructional Material Complementing FEMA 451, Design Examples
Development of PseudovelocityResponse Spectrum
0.00
5.00
10.00
15.00
20.00
25.00
30.00
35.00
0.0 1.0 2.0 3.0 4.0Period, Seconds
Pseu
dove
loci
ty, i
n/se
c
DTPSV ω≡)(
5% damping
If desired, an elastic (relative) velocity response spectrum could be obtained in the same way as the displacement spectrum. The only difference in the procedure would be that the peak velocity computed at each period would be recorded and plotted.Instead of doing this, the velocity spectrum is obtained in an approximate manner by assuming that the displacement response is harmonic and, hence, that the velocity at each (circular) frequency is equal to the frequency times the displacement. This comes from the rules for differentiating a harmonic function.Because the velocity spectrum so obtained is not exact, it is called the pseudovelocity response spectrum. Note that it appears that the pseudovelocity at low (near zero) periods is also near zero (but not exactly zero).
FEMA 451B Topic 3 Notes Slide 70
SDOF Dynamics 3 - 70Instructional Material Complementing FEMA 451, Design Examples
0.0
50.0
100.0
150.0
200.0
250.0
300.0
350.0
400.0
0.0 1.0 2.0 3.0 4.0Period, Seconds
Pseu
doac
cele
ratio
n, in
/sec
2
DTPSA 2)( ω≡
Development of PseudoaccelerationResponse Spectrum
5% damping
The pseudoacceleration spectrum is obtained from the displacement spectrum by multiplying by the circular frequencies squared. Note that the acceleration at a near zero period is not near zero (as was the case for velocity and displacement). In fact, the pseudoacceleration represents the total acceleration in the system while the pseudovelocity and the displacement are relative quantities.
FEMA 451B Topic 3 Notes Slide 71
SDOF Dynamics 3 - 71Instructional Material Complementing FEMA 451, Design Examples
The pseudoacceleration response spectrum represents the total acceleration of the system, not the relative acceleration. It is nearly identical to the true total acceleration response spectrum for lightly damped structures.
Note About the Pseudoacceleration Response Spectrum
0.0
50.0
100.0
150.0
200.0
250.0
300.0
350.0
400.0
0.0 1.0 2.0 3.0 4.0Period, Seconds
Pseu
doac
cele
ratio
n, in
/sec
2
5% damping
Peak groundacceleration
For very rigid systems (with near zero periods of vibration), the relative acceleration will be nearly zero and, hence, the pseudoacceleration, which is the total acceleration, will be equal to the peak ground acceleration.
FEMA 451B Topic 3 Notes Slide 72
SDOF Dynamics 3 - 72Instructional Material Complementing FEMA 451, Design Examples
m u t u t c u t k u tg r r r[&& ( ) && ( )] & ( ) ( )+ + + = 0
mu t c u t k u t mu tr r r g&& ( ) & ( ) ( ) && ( )+ + = −
PSA is TOTAL Acceleration!
-0.40
-0.20
0.00
0.20
0.40
0.00 1.00 2.00 3.00 4.00 5.00 6.00
TIME, SECONDS
GR
OU
ND
AC
C, g
Ground Acceleration Response History
gu&& tu&&ru&&
This slide explains why the pseudoacceleration is equal to the total acceleration. The relative displacement is multiplied by omega to get pseudovelocity. The pseudovelocity then is multiplied by omega to get the total acceleration.
FEMA 451B Topic 3 Notes Slide 73
SDOF Dynamics 3 - 73Instructional Material Complementing FEMA 451, Design Examples
Difference Between Pseudo-Accelerationand Total Acceleration
(System with 5% Damping)
0.00
50.00
100.00
150.00
200.00
250.00
300.00
350.00
0.1 1 10Period (sec)
Acce
lera
tion
(in/s
ec2 )
Total Acceleration Pseudo-Acceleration
This plot shows total acceleration and pseudoacceleration for a 5% damped system subject to the El Centro ground motion. Note the similarity in the two quantities. The difference in the two quantities is only apparent at low periods.The difference can be much greater when the damping is set to 10%, 20%, or 30% critical, and the differences can appear in a wider range of periods.
FEMA 451B Topic 3 Notes Slide 74
SDOF Dynamics 3 - 74Instructional Material Complementing FEMA 451, Design Examples
Difference Between Pseudovelocityand Relative Velocity
(System with 5% Damping)
0
5
10
15
20
25
30
35
40
0.1 1 10Period (sec)
Velo
city
(in/
sec)
Relative Velocity Pseudo-Velocity
This plot shows relative velocity and pseudovelocity for a 5% damped system subject to the El Centro ground motion. Here, the differences are much more apparent than for pseudoacceleration, and the larger differences occur at the higher periods. The differences will be greater for systems with larger amounts of damping.
FEMA 451B Topic 3 Notes Slide 75
SDOF Dynamics 3 - 75Instructional Material Complementing FEMA 451, Design Examples
Displacement Response Spectrafor Different Damping Values
0.00
5.00
10.00
15.00
20.00
25.00
0.0 1.0 2.0 3.0 4.0 5.0Period, Seconds
Dis
plac
emen
t, In
ches
0%5%10%20%
Damping
The higher the damping, the lower the relative displacement. At a period of 2 sec, for example, going from zero to 5% damping reduces the displacement amplitude by a factor of two. While higher damping produces further decreases in displacement, there is a diminishing return. The % reduction in displacement by going from 5 to 10% damping is much less that that for 0 to 5% damping.
FEMA 451B Topic 3 Notes Slide 76
SDOF Dynamics 3 - 76Instructional Material Complementing FEMA 451, Design Examples
Pseudoacceleration Response Spectrafor Different Damping Values
0.00
1.00
2.00
3.00
4.00
0.0 1.0 2.0 3.0 4.0 5.0Period, Seconds
Pseu
doac
cele
ratio
n, g
0%5%10%20%
Damping
Peak groundacceleration
Damping has a similar effect on pseudoacceleration. Note, however, that the pseudoacceleration at a (near) zero period is the same for all damping values. This value is always equal to the peak ground acceleration for the ground motion in question.
FEMA 451B Topic 3 Notes Slide 77
SDOF Dynamics 3 - 77Instructional Material Complementing FEMA 451, Design Examples
Damping Is Effective in Reducing the Response for (Almost) Any Given Period
of Vibration
• An earthquake record can be considered to be the combination of a large number of harmonic components.
• Any SDOF structure will be in near resonance with oneof these harmonic components.
• Damping is most effective at or near resonance.
• Hence, a response spectrum will show reductions due todamping at all period ranges (except T = 0).
Damping is generally effective at all periods (except at T = 0). The reason for this is that ground motions consist of a large number of harmonics, each at a different frequency. When a response spectrum analysis is run for a particular period, there will be a near resonant response at that period. Damping is most effective at resonance and, hence, damping will be effective over the full range of periods for which the response spectrum is generated.
FEMA 451B Topic 3 Notes Slide 78
SDOF Dynamics 3 - 78Instructional Material Complementing FEMA 451, Design Examples
Damping Is Effective in Reducing the Response for Any Given Period of
Vibration
Time (sec)
Am
plitu
de
• Example of an artificially generated wave to resemble a real time ground motion accelerogram.
• Generated wave obtained by combining five different harmonic signals, each having equal amplitude of 1.0.
-4.00-2.000.002.004.00
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
To demonstrate the point made in the previous slide, an “artificial” ground motion is made up from the sum of five simple harmonics.
FEMA 451B Topic 3 Notes Slide 79
SDOF Dynamics 3 - 79Instructional Material Complementing FEMA 451, Design Examples
The Artificial Wave Is the Sum of Five Harmonics
T = 5.0 s
T = 4.0 s
T = 3.0 s
Time (sec)
Am
plitu
de
-1-0.5
00.5
1
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
-1-0.5
00.5
1
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
-1-0.5
00.5
1
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
Each of the harmonics has an amplitude of 1.0. The first three of the harmonics with T = 5, 4, and 3 sec are shown.
FEMA 451B Topic 3 Notes Slide 80
SDOF Dynamics 3 - 80Instructional Material Complementing FEMA 451, Design Examples
T = 2.0 s
T = 1.0 s
Time (sec)
Am
plitu
de
Summation
-1-0.5
00.5
1
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
-1-0.5
00.5
1
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
-4.00-2.000.002.004.00
0.0 6.0 12.0 18.0 24.0 30.0 36.0 42.0 48.0 54.0 60.0 66.0 72.0 78.0 84.0 90.0
`
The Artificial Wave Is the Sum of Five Harmonics
The remaining two harmonics (at T = 2 and 1 sec) and the sum are shown.
FEMA 451B Topic 3 Notes Slide 81
SDOF Dynamics 3 - 81Instructional Material Complementing FEMA 451, Design Examples
FFT curve for the combined wave
Frequency (Hz)
Four
ier a
mpl
itude
0.00
2.00
4.00
6.00
8.00
10.00
12.00
14.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00
Frequency Ratio, β
Dyn
amic
Res
pons
e A
mpl
ifier
0.0% Damping5.0 % Damping10.0% Damping25.0 % Damping
Damping Reduces the Responseat Each Resonant Frequency
The Fourier amplitude spectrum of the artificial ground motion is shown at the left. This spectrum shows the five discrete harmonics that are in the artificial motion. If the response spectrum is run at intervals of 0.2 sec, there will be resonant response at each of these frequencies. Damping will be very effective in reducing the response at each of the frequencies.
FEMA 451B Topic 3 Notes Slide 82
SDOF Dynamics 3 - 82Instructional Material Complementing FEMA 451, Design Examples
Use of an Elastic Response SpectrumExample StructureK = 500 k/inW = 2,000 kM = 2000/386.4 = 5.18 k-sec2/inω = (K/M)0.5 =9.82 rad/secT = 2π/ω = 0.64 sec5% critical damping
0.00
2.00
4.00
6.00
8.00
10.00
12.00
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Period, Seconds
Dis
plac
emen
t, In
ches
At T = 0.64 sec, displacement = 3.03 in.
This is a simple example of the use of an elastic displacement response spectrum. If the system is assumed to have 5% damping (matching the spectrum) and the system period is known, the peak displacement may be easily computed. Note that the sign of the displacement (positive or negative) and the time that the displacement occurred is not known as this information was discarded when the spectrum was generated.
FEMA 451B Topic 3 Notes Slide 83
SDOF Dynamics 3 - 83Instructional Material Complementing FEMA 451, Design Examples
Use of an Elastic Response SpectrumExample StructureK = 500 k/inW = 2,000 kM = 2000/386.4 = 5.18 k-sec2/inω = (K/M)0.5 =9.82 rad/secT = 2π/ω = 0.64 sec5% critical damping
At T = 0.64 sec, pseudoacceleration = 301 in./sec2
0.0
50.0
100.0
150.0
200.0
250.0
300.0
350.0
400.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Period, SecondsPs
eudo
acce
lera
tion,
in/s
ec2
Base shear = M x PSA = 5.18(301) = 1559 kips
This is a simple example of the use of an elastic pseudoaccelerationresponse spectrum. If the system is assumed to have 5% damping (matching the spectrum) and the system period and mass are known, the peak base shear may be easily computed. Note that the sign of the shear (positive or negative) and the time that the shear occurred is not known as this information (related to pseudoacceleration) was discarded when the spectrum was generated.
FEMA 451B Topic 3 Notes Slide 84
SDOF Dynamics 3 - 84Instructional Material Complementing FEMA 451, Design Examples
Response Spectrum, ADRS Space
0.00
0.20
0.40
0.60
0.80
1.00
0.00 2.00 4.00 6.00 8.00 10.00 12.00
Displacement, inches
Pseu
doac
cele
ratio
n, g
Diagonal lines representperiod values, T
T = 0.64s
Another type of spectrum plot is the acceleration-displacement response spectrum (ADRS), which is also called a demand spectrum. Here, displacement is plotted on the x-axis and pseudoacceleration is plotted on the y-axis. Periods of vibration are represented as radial lines.This kind of spectrum is most commonly used in association with “capacity spectra” developed from nonlinear static pushover analysis. A demand spectrum is also useful in assessing stiffness and damping requirements of base-isolated systems.
FEMA 451B Topic 3 Notes Slide 85
SDOF Dynamics 3 - 85Instructional Material Complementing FEMA 451, Design Examples
0.1
1
10
100
0.1 1 10 100 1000
Circular Frequency ω, Radiand per Second
PSEU
DO
VELO
CIT
Y, in
/sec
1.0
D=10.0
0.01
.01
0.1
0.1 0.001
1.0
Line of increasingdisplacement
Line of constantdisplacement
Four-Way Log Plot of Response Spectrum
ωPSVD =
Circular Frequency ω(radians/sec)
Response spectra often are plotted on four-way log paper. This type of spectrum is often called a “tripartite spectrum” because the displacement, pseudovelocity, and pseudoacceleration are all shown on the same plot. On the plot, pseudovelocity is plotted on the vertical axis. Lines of constant and logarithmically increasing displacement are generated as shown. The use of circular frequency on the horizontal axis is rarely used in practice but is convenient for illustrating the development of the plot.
FEMA 451B Topic 3 Notes Slide 86
SDOF Dynamics 3 - 86Instructional Material Complementing FEMA 451, Design Examples
0.1
1
10
100
0.1 1 10 100 1000
Circular Frequency ω, Radiand per Second
PSEU
DO
VELO
CIT
Y, in
/sec
100
PSA=1000
10000
100
100000
10 1000
10000Line of increasingacceleration
Line of constantacceleration
Four-Way Log Plot of Response Spectrum
PSA PSV= ω
Circular Frequency ω(radians/sec)
Lines of constant and logarithmically increasing pseudoacceleration are obtained in a similar manner.
FEMA 451B Topic 3 Notes Slide 87
SDOF Dynamics 3 - 87Instructional Material Complementing FEMA 451, Design Examples
0.1
1
10
100
0.1 1 10 100 1000
Circular Frequency ω, Radiand per Second
PSEU
DO
VELO
CIT
Y, in
/sec
Four-Way Log Plot of Response Spectrum
10000
1000
100
10
10.1
ACCELERATIO
N, in/se
c2
100
10
1.0
0.1
0.01
0.001
DISPLACEMENT, in
Circular Frequency ω(radians/sec)
This is a completed spectrum for the 5% damped 1940 El Centro earthquake with maximum acceleration = 0.35g.
FEMA 451B Topic 3 Notes Slide 88
SDOF Dynamics 3 - 88Instructional Material Complementing FEMA 451, Design Examples
0.10
1.00
10.00
100.00
0.01 0.10 1.00 10.00
PERIOD, Seconds
PSEU
DO
VELO
CIT
Y, in
/sec
1.0
10.0
0.1
0.01
Acceleration, g
0.001
10.0
0.10
1.0
0.01
0.001
Displac
emen
t, in.
Four-Way Log Plot of Response SpectrumPlotted vs Period
Response spectra usually are plotted versus structural period or structural cyclic frequency. This is the same spectrum as shown in the previous slide, but it is plotted versus period.
FEMA 451B Topic 3 Notes Slide 89
SDOF Dynamics 3 - 89Instructional Material Complementing FEMA 451, Design Examples
Development of an ElasticResponse Spectrum
0.10
1.00
10.00
100.00
0.01 0.10 1.00 10.00
PERIOD, Seconds
PSEU
DO
VELO
CIT
Y, in
/sec
1.0
10.0
0.1
0.01
Acceleration, g
0.001
10.0
0.10
1.0
0.01
0.001
Displac
emen
t, in.
Problems with Current Spectrum:
It is for a single earthquake; otherearthquakes will have differentCharacteristics.
For a given earthquake,small variations in structural frequency (period) can producesignificantly different results.
The use of a single earthquake spectrum in structural design is not recommended for the reasons shown on this slide. The same site experiencing different earthquakes (or different components of the same earthquake) often will have dissimilar spectra.
FEMA 451B Topic 3 Notes Slide 90
SDOF Dynamics 3 - 90Instructional Material Complementing FEMA 451, Design Examples
0.1
1
10
100
0.01 0.1 1 10Period, Seconds
Pseu
do V
eloc
ity, I
n/Se
c
0% Damping5% Damping10% Damping20* Damping
1.0
10.0
0.1
0.01
Acceleration, g
0.001
10.0
0.10
1.0
0.01
0.001
Displac
emen
t, in.
For a given earthquake,small variations in structural frequency (period) can producesignificantly different results.
1940 El Centro, 0.35 g, N-S
Note the significant changes (for any given damping value) in the 1.5 sec period range.
FEMA 451B Topic 3 Notes Slide 91
SDOF Dynamics 3 - 91Instructional Material Complementing FEMA 451, Design Examples
0.1
1.0
10.0
100.0
0.01 0.10 1.00 10.00Period, seconds
Pseu
so V
eloc
ity, i
n/se
c
El CentroLoma PrietaNorth RidgeSan FernandoAverage
5% Damped Spectra for Four California EarthquakesScaled to 0.40 g (PGA)
Different earthquakeswill have different spectra.
The spectra are scaled to 0.4 g with 5% damping. Note the differences.
FEMA 451B Topic 3 Notes Slide 92
SDOF Dynamics 3 - 92Instructional Material Complementing FEMA 451, Design Examples
Smoothed Elastic Response Spectra(Elastic DESIGN Response Spectra)
• Newmark-Hall spectrum
• ASCE 7 spectrum
Because real ground motion spectra are difficult to work with in a design office, a variety of empirical spectra have been generated. One of the earliest of these empirical spectra was developed by Nathan Newmark. The next several slides describe this in detail. The spectrum used by ASCE 7-05 is simpler than the Newmark spectrum, but explanation of the background of the ASCE 7 spectrum is more difficult. Certain key aspects of the ASCE 7 spectrum are presented in the topic on seismic load analysis.
FEMA 451B Topic 3 Notes Slide 93
SDOF Dynamics 3 - 93Instructional Material Complementing FEMA 451, Design Examples
0.1
1
10
100
0.01 0.1 1 10 100Period (sec)
Disp
lace
men
t (in
)
0% Damping5% Damping10% Damping
Newmark-Hall Elastic Spectrum
Observations
gu&&max
gu&max
gumax
gvv &&&& max→
gvv max→
at short T
at long T
0→v
0→v&&
The Newmark spectrum is based on the following observations:• The pseudoacceleration at very low periods is exactly equal to the peak
ground acceleration.• The relative displacement at very long periods is exactly equal to the
peak ground displacement.• At intermediate periods, the displacement, pseudovelocity, and
pseudoacceleration are equal to the ground values times some empirical constant.
FEMA 451B Topic 3 Notes Slide 94
SDOF Dynamics 3 - 94Instructional Material Complementing FEMA 451, Design Examples
Very Stiff Structure (T < 0.01 sec)
Total accelerationZero
Ground accelerationRelative displacement
For very low period (high frequency) buildings, the maximum relative displacement will be zero. The maximum acceleration will approach the ground acceleration.
FEMA 451B Topic 3 Notes Slide 95
SDOF Dynamics 3 - 95Instructional Material Complementing FEMA 451, Design Examples
Very Flexible Structure (T > 10 sec)
Relative displacement Total acceleration
Ground displacement Zero
For very high period (low frequency) buildings, the maximum relative displacement will be equal to the maximum ground displacement. The maximum total acceleration will approach zero.
FEMA 451B Topic 3 Notes Slide 96
SDOF Dynamics 3 - 96Instructional Material Complementing FEMA 451, Design Examples
0.1
1
10
100
0.01 0.1 1 10Period, Seconds
Pseu
do V
eloc
ity, I
n/Se
c
0% Damping5% Damping10% Damping20* Damping
1.0
10.0
0.1
0.01
Acceleration, g
0.001
10.0
0.10
1.0
0.01
0.001
Displac
emen
t, in.
1940 El Centro, 0.35 g, N-S
0.35g
12.7 in/s
4.25 in.
Ground Maxima
The yellow line shows the maximum recorded ground displacement, velocity, and acceleration from the 1940 El Centro earthquake. These lines clearly form a lower bound to the elastic response spectra. Note how the building response displacements, velocities, and accelerations are amplifications of the ground values. Note also how the amplifications decrease with increased damping.
FEMA 451B Topic 3 Notes Slide 97
SDOF Dynamics 3 - 97Instructional Material Complementing FEMA 451, Design Examples
Damping One Sigma (84.1%) Median (50%)% Critical aa av ad aa av ad
.05 5.10 3.84 3.04 3.68 2.59 2.011 4.38 3.38 2.73 3.21 2.31 1.822 3.66 2.92 2.42 2.74 2.03 1.633 3.24 2.64 2.24 2.46 1.86 1.525 2.71 2.30 2.01 2.12 1.65 1.397 2.36 2.08 1.85 1.89 1.51 1.2910 1.99 1.84 1.69 1.64 1.37 1.2020 1.26 1.37 1.38 1.17 1.08 1.01
Newmark’s Spectrum Amplification Factorsfor Horizontal Elastic Response
Newmark has developed a series of amplification factors to be used in the development of design spectra. These are based on the average of dozens of spectra recorded on firm soil sites for the western United States. Values are shown for the median and median plus one standard deviation.
FEMA 451B Topic 3 Notes Slide 98
SDOF Dynamics 3 - 98Instructional Material Complementing FEMA 451, Design Examples
Newmark-Hall Elastic Spectrum
1
3
2 4
65
1) Draw the lines corresponding to max ggg
vvv ,, &&&
2) Draw line from Tb to Tc
Ta Tb Tc Td Te Tf
gAv&&maxα
3) Draw line from Tc to Td
gVv&maxα
4) Draw line from Td to Te
gDvmaxα
5) Draw connecting line from Ta to Tb
6) Draw connecting line from Te to Tf
These are the steps in the development of the Newmark spectrum. Note that actual values are not present.
FEMA 451B Topic 3 Notes Slide 99
SDOF Dynamics 3 - 99Instructional Material Complementing FEMA 451, Design Examples
ASCE 7Uses a Smoothed Design Acceleration Spectrum
“Long period”acceleration
TS T = 1.0Period, T
Spec
tral
Res
pons
e A
ccel
erat
ion,
Sa SDS
SD13
2
1
“Short period”acceleration
1
3
2
S = 0.6 ST
T+0.4 SaDS
0DS
S = Sa DS
S = ST
aD1
Note exceptions at larger periods
TL
4 D1SLa 2TS =T
4
This plot shows the basic relationships used for the ASCE 7 spectrum. Note that the vertical axis is pseudoacceleration. The spectrum is derived from a series of maps giving spectral acceleration values for “short period” (T = 0.2 sec) or “long period” (T = 1 sec) buildings. Note that the part of the spectrum to the right of TL (Curve 4) was introduced in the 2003 NEHRP Recommended Provisions and in ASCE 7-05.The maps are based on very stiff soils. For design purposes, the acceleration spectra is not reduced to the ground acceleration at low periods (Line 1 on the plot). Damping is assumed to be 5% critical.
FEMA 451B Topic 3 Notes Slide 100
SDOF Dynamics 3 - 100Instructional Material Complementing FEMA 451, Design Examples
The ASCE 7 Response Spectrum
is a uniform hazard spectrum based onprobabilistic and deterministic seismichazard analysis.
This slide notes that the ASCE 7 spectrum is a “uniform hazard spectrum.”This concept is covered in detail in the topic on seismic hazard analysis. The main purpose of this side is a transition into the hazards topic.