DURING OPERATION.

SQUEEZE CHUTE#191440

SIOUX STEEL

FROM ALL HINGED AND MOVING PARTSWARNING!: KEEP HANDS & FINGERS AWAY

SIOUX STEEL COMPANY, P.O. BOX 1265, SIOUX FALLS, SOUTH DAKOTA 571011-800-557-4689

MANUAL NO: 193738CREATED: 12/2011REV C: 11/6/2012 KAG ECN 12-165

CONTENTS

SAFETY PG 2

REPAIR/REPLACEMENT PARTS PG 3-4

FIG. A- MAIN ASSEMBLY BREAK DOWN PG 5

FIG. B- MAIN FRAME ASSEMBLY PG 6

FIG. C- LH LARGE DOOR ASSEMBLY PG 7

FIG. D- RH LARGE DOOR ASSEMBLY PG 8

FIG. E- SLICK DOOR ASSEMBLY PG 9

FIG. F- LH PALP DOOR ASSEMBLY PG 10

FIG. G- RH PALP DOOR ASSEMBLY PG 11

RATCHET LOCK INSTALLATION PG 12

ROPE INSTALLATION PG 13

AUTO/MANUAL HEAD GATE (OPTIONAL) INSTALLATION PG 14

PALP DOOR SQUEEZE (OPTIONAL) PG 15

WARRANTY PG 16

1

SAFETY Watch for this symbol. It points out important safety precautions. It means “Attention – Be Alert!”

DEFINITIONS: CAUTION: Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.

WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.

DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or serious injury. If any decals become damaged, detached, or illegible contact your dealer or Sioux Steel Company at (800)-557-4689 for free replacements. A careful operator, is the best operator. To help prevent accidents, read the following precautions before operating this equipment. Equipment should be operated only by those who are responsible and knowledgeable of this type of equipment. Carefully review the procedures given in this manual with all operators. It is important that all operators be familiar with and follow safety precautions. Improper use of equipment can cause serious injury or death. 1. Read the operator's manual before operating equipment.

2. Keep hands, arms, feet, and legs away from all pinch points.

3. DO NOT remove any safety devices that have been provided for your protection.

4. DO NOT work around the equipment in loose clothing that might catch in any moving parts.

5. DO NOT modify the equipment without consulting a dealer or Sioux Steel Co.

6. Do NOT clean, lubricate, or adjust equipment, while equipment is operating.

7. Inspect the equipment regularly for any damage before and after each use. If damage to equipment occurs, equipment should not be used until repairs are made. Immediately, contact your dealer or Sioux Steel Warranty Department at (800) 557-4689. Repair of damages should be implemented as soon as practical, with appropriate Sioux Steel replacement parts. REMEMBER: Sioux Steel Co. includes all reasonable means for accident prevention except a safe and careful operator.

2

REPAIR/REPLACEMENT PARTS LISTNotes:- The Sioux Steel Squeeze Chute has been completely assembled at the factory.

- Before operating, install Ratchet Lock and Rope per customer preference. Ratchet Lock and Rope can be installed on either side of chute. See Ratchet Lock and Rope installation sections of manual for additional details.

- Before operating, apply grease to grease zerks. Oil all other hinged and moving parts.

- Grease and oil as needed.WARNING!

KEEP HANDS AND FINGERS AWAY FROM ALL HINGEDAND MOVING PARTS DURING OPERATION.

ITEM NO.

PART NUMBER DESCRIPTION QTY.

1 189767 FRAME WLDT 12 191386LH LARGE DOOR- LH 13 189776 PIVOT WLDT - SM 24 191386RH LARGE DOOR RH 15 189724 SMALL DOOR - LH 16 189724RH SMALL DOOR- RH 17 191399 RATCHET ASSEMBLY 18 191398 RATCHET LOCK ASSY 19 191433W SLICK DOOR WELDMENT 110 197610 PALP DOOR SQUEEZE (OPTIONAL) 111 191527W PUSH BAR 112 195367 SERIAL NUMBER DECAL 113 191384 FLOOR PLANK 214 191523 FLOOR PLANK 8X125 215 191535 HANDLE GRIP 1.0" SQ 216 159781 NUT- .375 HEX -16 ELASTIC LOCK GR5 ZP 1817 189708 PALP DOOR HANDLE 118 173803 DECAL - "SIOUX" OVAL 4.13" x 7" 219 189708LH PALP DOOR HANDLE LH 120 176756 FLAT WASHER- 3/4" 221 154066 FLATWASHER - 3/8" WIDE SERIES 1022 191524 BLINDER 30X10 223 196474 2 X 3 PLASTIC TUBE PLUG 624 173990 ZERK- 1/4" DRIVE IN 5025 195827 WARNING DECAL "PINCH POINT" 326 195828 WARNING DECAL "PINCH POINT" 627 189738 STOP PLATE- BUTT BAR 1028 191529 HANDLE GRIP 1.25 SQ 629 191525 SMALL BLINDER 1230 166543 5/8" NYLOCK NUT 131 196459 SCREW- .625 HHC-11 X 3.5 GR5 ZP 132 154071 5/8" FLAT WASHER BZ 233 189515 1/2-13 LOCK NUT 2034 154069 WASHER - 1/2 FLAT TYPE A/W SERIES ZP 26

3

REPAIR/REPLACEMENT PARTS LIST (CONT.)ITEM NO.

PART NUMBER DESCRIPTION QTY.

35 190006 SCREW- .50 HHC X 3.5 1436 158981 HEX BOLT- 1/2-13 UNS X 7.500 G8 237 191536 SPRING- DIE 4.0 X .5 238 191546 CAP-PLAS HNDL 1.315RNDX5"/BLK 139 187321 DECAL- SIOUX OVAL 2.63 X 4.87 240 191545 HANDLE CAP 241 191495 HANDLE WELDMENT 242 191419W LINK WELDMENT 143 10516KW BUSHING 444 154051 NUT - 3/8-16UNC GR5 ZP 245 169367 WASHER 7/16" TYPE A/W SERIES ZP 1446 169365 7/16-14 X 2 HEX HD CAPSCREW 247 191566 7/16" NYLOCK LOCK NUT 1248 169366 7/16-14 X 1 1/2 HEX HD CAPSCREW 1049 191783 EYE-BOLT- 38 X 8 150 191557 SPRING- EXT. 7/8 X 4 151 169703 COTTER PIN - 1/8" x 1" ZP 452 176082 7/16"HEX IDx1.63"x0.8" ROLLER BEARING 453 189779 SPACER TUBE- BEARING 254 176081 1/2" RUE COTTER PIN RING 255 191622 Stop Pin Wldt 156 191767 HAIR PIN COTTER 0.148 X 3.3125 157 191544 PULLEY - ROPE 158 196552 UPPER PIVOT ASSY 260 191750 SCREW- .50 HHC X 4.5 161 191462 Spring- Compression 2.75 OD x 6.25 162 191537 HANDLE CAP .750 663 191556 SWIVEL EYE PULLEY 264 191562 PULL ROPE HANDLE 165 191565 RATCHET HANDLE SPACER 266 173991 PLUG - 2" SQUARE 867 191463 SPRING- EXTENSION 1.50 X 8.50 168 191571 TUBE- FLOOR BRACE 669 191580 BRISKET BAR REAR HOLD DOWN 170 191579 BRISKET BAR FRONT HOLD DOWN 171 163137 BOLT, 3/8-16UNC X 3" CARRIAGE 1672 162476 3/8" FENDER WASHER 1673 196489 WASHER- .250 FENDER 1.00 OD 5274 196490 1/4x1.00 DRILL SCREW- PAN HEAD 5275 197654 ROPE- 7/16 SOLID BRAID NYLON 10ft

76 198400 OR 194538

HEAD GATE AUTO OR MANUAL (OPTIONAL) 1

4

(NOT SHOWN)

FIGURE B

FIGURE EASSEMBLYSLICK DOOR

FIGURE GASSEMBLYRH PALP DOOR

FIGURE FASSEMBLY

LH PALP DOOR

LH LARGE DOORASSEMBLYFIGURE C

FIGURE DASSEMBLYRH LARGE DOOR

FIGURE AMAIN ASSEMLBY BREAK DOWN

MAIN FRAME

76SEE NOTES BELOW

HEAD GATE

ASSEMBLY

OPTIONALAUTO OR MANUAL

ROPE(NOT SHOWN)

SEE NOTES BELOW75

NOTES: - SEE HEAD GATE INSTALLATION SECTION FOR ADDITIONAL DETAILS ON AUTO OR MANUAL HEAD GATE.- SEE ROPE INSTALLATION SECTION FOR ADDITIONAL DETAILS ON ROPE.- SEE PALP SQUEEZE SECTION FOR ADDITIONAL DETAILS ON PALP SQUEEZE.

OPTIONALPALP DOOR SQUEEZE

(NOT SHOWN)SEE NOTES BELOW

10

5

MAIN FRAME ASSEMBLYFIGURE B

SCALE 1 : 15DETAIL B

16

71

72

38

33

70

3

1

63

6364

58

58

12

33

8

23

3534

11

2424

6869

35

23

23

34

14 13 13

14

3132

30

3334

35

A

B

C

62

6533

34

3534

34

DETAIL A SCALE 1 : 10

33

33

25

3 23

26

6133

60

24

34

50

35

33

34

DETAIL C SCALE 1 : 10

36

34

37

34

6

LH LARGE DOOR ASSEMBLYFIGURE C

45

24

24

62

4827

29

28

7374

25

24

22

24

24

74

73

26

24

47

2

62

24

66

7

24

29

4

7473

62

66

2873

74

47

45

48

27

2224

24

24

24

24

24

62

RH LARGE DOOR ASSEMBLYFIGURE D

8

SLICK DOOR ASSEMBLYFIGURE E

24

24

9

41

4039

26

3433

35

43

45

46

56 5567

4249

21

44

44

45

66

47

4645

43

66

51

45

24

47

24

40

41

51

39

24

D

57

33

53

52

DETAIL D SCALE 2 : 9

52

5352

52

9

5

15

18 17

51

16

21

20

LH PALP DOOR ASSEMBLYFIGURE F

10

6

51

18

21

16

19

20

15

RH PALP DOOR ASSEMBLYFIGURE G

11

65

65

8

SCALE 1 : 8DETAIL D

60

33

34

34

61

RATCHET LOCK INSTALLATION

BE INSTALLED ON EITHERSIDE OF CHUTE

RATCHET LOCK CAN

D

FIGURE H

12

ROPE INSTALLATIONNOTE: ROPE CAN BE INSTALLED ON EITHER SIDE OF CHUTE AS SHOWN BELOW.

FIGURE I

FIGURE J

INSTALL LH OPTION

LINK CONTROL ARMONTO SLICK DOOR

AROUND PULLEYPASS ROPE

DROP PULLEYPASS ROPE THRU

TIE END OF ROPEPASS ROPE THRU PULLEY,AT DESIRED LOCATION,

HOOK DROP PULLEY

HANDLE ITEM 64AND TIE TO PULL ROPE

75 ROPE

INSTALL RH OPTION

LINK CONTROL ARMONTO SLICK DOOR

AROUND PULLEYPASS ROPE

DROP PULLEYPASS ROPE THRU

TIE END OF ROPE

PASS ROPE THRU PULLEY,AT DESIRED LOCATION,HOOK DROP PULLEY

HANDLE ITEM 64AND TIE TO PULL ROPE

75 ROPE

13

DETAIL G SCALE 1 : 12

INSTALL ONTOFRAME AS

SHOWN

S194538MANUAL HEAD GATE

FIGURE M

36

SCALE 1 : 12DETAIL E

33

34

34

34

37

ATTACH HEAD GATE TO MAIN FRAME AS SHOWN

FIGURE K

E

F

F

TYPICAL BOTH SIDE

AUTO & MANUAL HEAD GATE (OPTIONAL) INSTALLATION

TYPICAL BOTH SIDES

33

ATTACH SAFTEYCHAIN TO 1/2"BOLT

DETAIL F SCALE 1 : 12

34

S198400AUTO HEAD GATE

FIGURE L

14

PALP DOOR SQUEEZE (OPTIONAL)

FIGURE O

PALP DOOR SQUEEZECAN BE INSTALLED ONEITHER LH OR RH PALPDOORS

PALP DOOR

FIGURE NS197610- PALP DOOR SQUEEZE (ITEM 10)

15

{00659155.1}

NEW PRODUCT WARRANTY

LIVESTOCK EQUIPMENT LIMITED WARRANTY FOR NEW SIOUX STEEL COMPANY PRODUCTS

A. GENERAL PROVISIONS. “Sioux Steel” means Sioux Steel Company, 196 1/2 East Sixth Street, Sioux Falls, South Dakota 57104. The warranties described below are provided by Sioux Steel to the original purchasers of new products purchased from Sioux Steel or from an authorized Sioux Steel Dealer (the “Products”). Under these warranties, Sioux Steel will, at its option, repair or replace at its factory any Product covered under these warranties which is found to be defective in material and workmanship during the applicable warranty term or refund the purchase price paid for the defective Product. Customer will be responsible for labor charges for removing the defective Product and reinstalling the repaired or replacement Product, any premium charge for overtime labor requested of Sioux Steel and shipping charges to and from Sioux Steel’s factory. These warranties are not transferrable. B. WARRANTY PERIOD. Subject to exclusions and limitations set forth herein, each new Product is warranted for the number of years specified below. Each warranty term begins from the date of purchase regardless of delay in receipt of the Product by Customer due to the time required to process, handle, ship, assemble, construct and install the Product. Customer must retain proof of the date of purchase. Replacement parts for and repairs to the Product will be warranted only for the remainder of the original warranty term. The replacement parts for or repairs to the Product will not extend the warranty term beyond the original warranty term. Products described below include all parts, components and accessories.

LIVESTOCK EQUIPMENT Victory, Cattleman’s, Heavy Duty and Super Six steel construction livestock gates labeled through the Company’s “Lifetime Guarantee Gate Program” (“Lifetime Guaranteed Gates”)

Lifetime

All Poly Products 2 years Post Puller/Pounder Consumer Use 1 Year Commercial or Government Use 6 Months All Other Livestock Equipment, including Bulk Bins and all Livestock Gates that are not labeled through the “Guarantee Gate Program” as provided above

1 Year

Exclusions specific to Livestock Equipment: Damage or loss of any kind from (1) storage of feed products that are not free-flowing or that have a density greater than 40 pounds per square foot; and (2) the storage of materials other than free-flowing livestock feed. C. ITEMS COVERED SEPARATELY. The Sioux Steel warranties do not cover any parts, components or materials that are part of the Product, or used in conjunction with the Product, that are not manufactured by Sioux Steel. Such parts, components and materials will be subject to the warranties provided by the manufacturer, if any. D. WHAT IS NOT WARRANTED. Sioux Steel does not warrant and is not responsible for the following: (1) used products; (2) modification or alteration of the Products; (3) Products that have not been properly installed or not installed in accordance with the instruction manual, improper assembly, or improper construction by any persons other than Sioux Steel employees; (4) depreciation, damage or loss caused by the use of parts, components or accessories not provided by Sioux Steel, unauthorized repairs, normal wear, lack of necessary and proper maintenance, a failure to follow operating instructions/recommendations, misuse, lack of proper protection during storage, vandalism or theft, exposure to the elements or corrosive materials, accidents or acts of nature including lightning, flooding, hail, straight winds and tornadoes; and (5) cosmetic damage or damage that does not hinder the functionality of the Products. E. LIFETIME GUARANTEED GATES. The Limited Warranty for New Sioux Steel Company Products shall apply to the Lifetime Guaranteed Gates (“Gates”) for the life of the original purchaser with the exception of Section D above. Sioux Steel does not warrant and is not responsible for the following: (1) modification or alteration of the Gates; (2) cosmetic damage, normal wear and tear or damage that does not hinder the functionality of the Gates, including fading of the color; (3) damage caused by use for purposes inconsistent with its intended purpose or design; (4) damage due to use of any parts or components not supplied by the Sioux Steel. F. LIMITATIONS OF WARRANTIES AND CUSTOMER’S REMEDIES. To the extent permitted by law, neither Sioux Steel, the Dealer nor any person or company affiliated with either of them makes any warranties, representations, conditions or promises express or implied as to the quality, performance or freedom from defects of the Products covered by these warranties other than those set forth herein. THERE ARE NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NEITHER SIOUX STEEL, THE DEALER, NOR ANY PERSON OR COMPANY AFFILIATED WITH EITHER OF THEM WILL BE LIABLE FOR ANY DAMAGES, INCLUDING, BUT NOT LIMITED TO, INCIDENTAL, SPECIAL, EXEMPLARY, CONSEQUENTIAL, LOST PROFITS AND REVENUES, LOST USE OF THE PRODUCTS OR ANY OTHER PROPERTY, BODILY INJURY OR PROPERTY DAMAGE CLAIMS OF ANY PERSON, LOST COMMODITIES, REMOVAL OR STORAGE COSTS FOR THE PRODUCTS, OTHER EQUIPMENT AND COMMODITIES, DAMAGE TO THE ENVIRONMENT ARISING FROM OR IN ANY MANNER RELATED TO ANY RELEASE OF HAZARDOUS MATERIALS, AND REMEDIATION EXPENSES THEREFORE, WHETHER BASED ON CONTRACT, TORT, STRICT LIABILITY OR ANY OTHER LEGAL BASIS, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO INSTANCE WILL SIOUX STEEL, THE DEALER OR ANY PERSON OR COMPANY AFFILIATED WITH EITHER OF THEM BE LIABLE TO CUSTOMER OR ANY PERSON IN AN AMOUNT IN EXCESS OF THE PURCHASE PRICE PAID BY CUSTOMER FOR THE PRODUCT. G. NO DEALER WARRANTY. THE DEALER HAS NO AUTHORITY TO MAKE ANY WARRANTY, REPRESENTATION, CONDITION OR PROMISE ON BEHALF OF SIOUX STEEL, OR TO MODIFY THE TERMS OR LIMITATIONS OF THIS WARRANTY IN ANY WAY. H. GOVERNING LAW/VENUE. These warranties, and all terms set forth herein, are governed by the laws of the State of South Dakota and, where applicable, the laws of the United States of America. Any and all disputes arising from these warranties, the purchase and use of the Products, bodily injury and property damage claims or otherwise must be venued in the South Dakota Circuit Court sitting in Minnehaha County, South Dakota. Customer agrees to such venue and waives any challenge to such court’s jurisdiction based upon lack of personal jurisdiction or inconvenience. I. SECURING WARRANTY SERVICE. In order to receive warranty services, customer must give Sioux Steel written notice of a warranty claim within 30 days of the date of discovery of the defective materials or workmanship, and Customer must complete the following steps:

(1) Obtain from Sioux Steel a Return Goods Authorization Number (“RGA Number”) by calling the Customer Service Department at 1-800-557-4689, and providing the following information:

An explanation as to why the Product is being returned. The name of the territory representative, Dealer or Sioux Steel salesperson from whom the Product was purchased. The Dealer’s identification number. The invoice number and date of purchase. Customer’s name, phone number, fax number, mailing address and email address. The date that the Product will be returned.

(2) Pay the shipping charges to ship the Product to Sioux Steel’s factory, and the return shipping charges. (3) Ship the Product to Sioux Steel at 196 1/2 East Sixth Street, Sioux Falls, South Dakota 57104.

16