The Grapevine SEAMER & TAME BRIDGE MAGAZINE No. 136. December 2015 - January 2016
Series 10 Seamer User Manual 8271
-
Upload
john-jenner -
Category
Documents
-
view
269 -
download
10
description
Transcript of Series 10 Seamer User Manual 8271
Sales & Service LtdEUROCAN
User Manual
Series 10 Seamer
Eurocan Sales and Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Copyright © 2014 Eurocan Sales & Service Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written consent of Eurocan Sales & Service Ltd. While every precaution has been taken in the preparation of this manual, Eurocan Sales & Service Ltd and the author assume no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. All product and company names are trademarks of their respective companies and licenses.
Eurocan Sales and Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Introduction
Eurocan has designed this machine to be durable and operator friendly, and to give reliable production.
To ensure the machine meets all expectations, please read and comply with this instruction manual, whichis an important resource for all personel involved in the operation, maintenance, lubrication and cleaning of the machine. The manual provides the information needed to safely operate and maintain the machine.
Thank you for purchasing aEurocan can closing machine.
Important tags mark information about the best way to operatethe machine to maximise durability and production.
It is important that all personnel read and understand the Safety section before operating the machine, and read all Caution notices about possible hazards before making adjustments or changes.
For best performance of the machine, always use original Eurocan parts. For further support, and to order additional User Manuals or spare parts, please contact:
Eurocan Sales & Service LtdUnit B1 Newbrook Business ParkPound Lane, Upper BeedingBN44 3JD, U.K.
Tel: +44 (0)1903 810110 Fax: +44 (0)1903 810222 Email: [email protected]
i
!
Contents
Eurocan Sales and Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Safety Information
Machine Overview
Specification
Installation
Set Up
Change Over Procedure
Operation
Maintenance
CE Declaration of Conformity
Assembly Drawings & Parts Lists
Section Title
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
1.0 Safety Information
MAKE SAFETY A DAILY HABIT
Safety depends on everyone who operates, maintains, services or works nearby operating equipment. Personnel should NOT operate this machine until trained on its function and purpose: know and understand the principles of your equipment before operating it. Remember: an accident is usually caused by carelessness, neglect or oversight. Where machines are shown without guards this is for illustration purposes only. Throughout this manual are listed a number of safety precautions. Study them carefully and follow them, also insist upon those working for you doing the same. The following signal words are used to inform about potential hazards and proper machine usage.
i Important Identifies specific information that will assist with machine operation, prevent
damage to the machine, or extend the life of machine parts
! Caution Alerts to a potential hazard that may result in personal injury, or an unsafe practice
that causes damage to the equipment if not avoided
Installation Only trained machinery movers, using appropriate and well-maintained equipment, should handle, move and install the machine. Please refer to the Installation chapter in this manual for complete instruction and safety information.
Guards
Guards are supplied with the machine and must be in place before operation begins. NEVER bypass or disconnect safety switches. Doing so could greatly increase the chance for personal injury. Guards are installed to protect personnel working on or around the machine. Guards MUST be closed when the machine is operating. Safety switches are located on each guard. If a guard is opened while the machine is running, the machine stops. Never reach over or into moving machinery with hands, rags or any tools. Guard design is based on level machine footings that are even with the work area. Raising the machine or using platforms, staircases, stools or ladders near the machine creates hazardous operating conditions. Guards shield personnel from moving parts. Reaching over, under or through a guard, or blocking it open is EXTREMELY hazardous and must NEVER be attempted. Guards should NEVER be altered from factory setup. Work with special care when guards are removed for lubrication, adjustment and part replacement. All guards should be reinstalled correctly immediately following maintenance or repair.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Opening a guard DOES NOT disconnect electrical power in the control cabinet. To disconnect control power, padlock the main disconnect in the OFF position.
Machine Location
The machine location must provide sound footing, adequate lighting and accessibility from all sides. DO NOT install the machine in a combustible environment or near combustible or explosive material. DO NOT smoke, solvent gasses are inflammable. Keep the area around the machine clean and free of obstacles to avoid injuries due to falls.
Nip & Pinch Points Be EXTREMELY careful when working near nip points and pinch points. Keep body parts, hair, neckties, clothing, and tools away from these hazards to prevent serious injury or death. DO NOT wear rings, watches or necklaces near the machine. All notices, labels, and plates must be in place and legible. Immediately replace damaged or missing labels and notices. Contact Eurocan Sales & Service Ltd for replacement notices, labels, and plates.
Electrical A qualified electrician must install and repair electrical equipment and verify electrical ground. Complete electrical information is provided in the electrical drawings in this manual. ALWAYS padlock the electrical disconnect in the OFF position before adjusting, cleaning, lubricating or maintaining the machine. NEVER use jumper wires to bypass electrical circuits. Doing so may activate parts of the machine which could cut, crush or seriously injure persons in the immediate area. Modifications or additions to the electrical system causes machine malfunction and creates safety hazards for personnel. Always stop the drive motor before servicing. Be certain that the power cannot be turned on again without your knowledge.
Specific lubrication instructions are located in the Maintenance section of this manual.
• Lubricate manual fittings BEFORE operation.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
2.0 Machine Overview
The Series 10 Can Seamer is a modern all stainless steel single head semi-automatic can closer designed for compliance with food safety and hygiene standards and providing exceptional double seaming integrity of tinplate, aluminium, paperboard or plastic cans and ends.
A double seam is formed in two operations, with the first operation performing ninety percent of the work. Uniquely, the 10A rotates the can thirteen times during this first operation to achieve optimum first operation seam specifications, before the second operation finishes the process of tightening the seam. As the food industry strives to use thinner and lighter weight can ends, it is imperative that the maximum number of first operation revolutions is employed so that the end hook can be formed smoothly to achieve the desired level of low-amplitude wrinkles.
Filled cans with the loose end or closure on top are placed on the lifter plate by the operator, who then depresses the twin safety buttons simultaneously using both hands to start the pneumatic actuation. The lifter raises the can to clamp it to the driven seaming chuck, and the can starts rotating in the industry preferred clockwise direction which is beneficial to the formation of the double seam. A second pneumatic cylinder then automatically actuates the trigger mechanism to initiate the double seaming cycle, and the lifter lowers, allowing the operator to remove the seamed can and place the next one in position.
To comply with the criteria for wash-down certified food packaging equipment, the frame fabrication, safety guarding and mechanical parts are manufactured from food grade 316 stainless steel and the tooling, including the seaming cam, is manufactured from vacuum hardened 440C martensitic stainless steel. The 10A can be washed with the same cleaning agents as used on a can filler.
The first and second operation seaming rolls are mounted on double row angular contact sealed for life ball bearings. Bearing replacement is cost effective and easy. Grease lubrication is used throughout the seamer with food grade grease specified as standard.
1st and 2nd operation seam adjustments are facilitated by easy access adjusting screws in the top of the seaming head assembly. Seaming roll height is set simply using the threaded seaming roll pin and lock nut. Pin height is set using a fine threaded adjuster on the lifter shaft sleeve, and base pressure is changed with the aid of an integral pressure adjusting nut on the lifter spring holder.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
The seaming head assembly is raised and lowered for can height changes using a hand wheel mounted on a lead screw assembly. Can diameter changes are as simple as changing the seaming chuck and re-setting the seaming rolls. It may also be necessary to change seaming roll assemblies and the lifter plate depending on the can design and specification. All can size change-overs can be accomplished within fifteen minutes or less.
The Series 10 seamer is a modern food safe and cost effective can closing machine, designed to work with light weight cans and ends to achieve optimum double seam integrity. In addition to the standard 10A model for atmospheric can closing applications, it is also offered in a 10V vacuum option, 10G nitrogen gassing option, and 10VG vacuum and gassing option.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
3.0 Specification
Model number 10A single head semi-automatic seamer
Maximum output 10 cans per minute Can diameter range 52 – 153 mm Can height range 50 – 300 mm
Air pressure
70 PSI / 5 Bar
Electric power 1.1 kW
Electric supply 240 Volt, 13 Amp, single phase Net weight 216 kg
Gross weight 270 kg
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Dimensions
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
4.0 Installation Machine Delivery When the machine arrives, inspect the entire shipment for damage. If you find any damage please note this on the carrier delivery receipt, and send delivery details and a photograph of the damage to [email protected].
• Use competent machinery movers when the machine arrives. • Confirm the weight of the machine. • Study the mass and weight distribution of the machine.
Prepare Site Select the machine site carefully. The structure must support the machine and production activities. The area should be well lit for operator efficiency and accessible from all sides for service, maintenance and operation. The area should also have appropriate electrical and compressed air connections available.
Lift & Move the Machine
! Caution When lifting or moving the machine adhere to the following guidelines to
prevent harm to personnel or machinery:
• Use the specified lifting points. Damage resulting from incorrect lifting may require the machine be returned to the manufacturer for repair at the customer’s expense.
• Handling, moving and installation should be done only by trained machinery movers using appropriate equipment.
• Use equipment with adequate capacity.
• Prevent anyone from walking, crawling, or reaching under the machine while it is solely supported by a forklift or other device.
• Keep hands and feet clear of the machine, platform, or pallet base and the wheels of the lifting equipment.
• Watch for overhead utility lines, low clearances, and other obstructions.
• Before lifting the machine, remove all unsecure items and fasteners from the pallet base.
i Important When lifting and moving the machine a fork lift and wide pallet truck is required.
1. Undo the bolts securing the machine to the wooden base used for transport. 2. Position the lift truck at the front of the machine with the lifting forks underneath the
integral lifting arms of the machine stand. 4. Slowly lift the machine with care. A sudden jar may affect the alignment of parts. 5. Remove the wooden base. 6. Lower and position the machine onto the floor. 7. Remove the lift truck. 8. To move the machine around in the work area use a wide pallet truck positioned
underneath the integral lifting arms on the machine stand.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Connect the Air Supply Supply clean dry air and use pipe that is at least the size of the inlet. The air pressure required for the machine is 70 PSI (5 Bar).
i Important The exact air consumption may vary slightly. Consumption depends on
model, speed, and auxiliary equipment. Prepare the Machine for Work
i Important The machine is adjusted and checked at the factory, but it is absolutely
necessary to check all the adjustments described in the Set Up section of the manual before operating the machine. Thoroughly clean the machine to remove any dust and dirt which has accumulated during transportation. Connect Machine to the Power Supply
Plug the power cable into a standard 13 Amp wall socket.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
5.0 Set Up 5.1 Remove seaming head guard
Undo the socket head cap screws retaining the guard.
Tilt the guard forward and down, and slide it off.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
5.2 Set pin height
Place a can on the lifter plate without an end component.
Release the seaming head clamp screws.
Use the hand wheel to raise or lower the seaming head until the top of the chuck lift face is 1 mm below the can flange.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Tighten the seaming head clamp screws.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
5.3 Set 1st operation seaming roll
Attach the supplied handle to the driven pulley.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Rotate handle while manually pressing the trigger arm.
Continue to rotate until the 1st operation seaming cam roller is positioned on the 1st operation cam profile as in the picture below.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Pull back the trigger arm.
Insert a screwdriver between the body of the 1st operation seaming roll and seaming chuck.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Undo the hexagon setscrew.
Undo the lock nut on the 1st operation seaming roller adjusting screw.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Refer to your double seam data sheet for the 1st operation seaming roll setting dimension, and use feeler gauges to this value in between the 1st operation roll body and the chuck body.
Turn the adjusting screw to move the 1st operation roll in or out until the feeler gauges are a tight slide fit.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Re-tighten the lock nut on the 1st operation seaming roller adjusting screw.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Re-tighten the hexagon setscrew.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
5.4 Set 2nd operation seaming roll
Rotate handle while manually pressing the trigger arm.
Continue to rotate until the 2nd operation seaming cam roller is positioned on the 2nd operation cam profile as in the picture below.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Pull back the trigger arm.
Insert a screwdriver between the body of the 2nd operation seaming roll and seaming chuck.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Undo the hexagon setscrew.
Undo the lock nut on the 2nd operation seaming roller adjusting screw.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Use feeler gauges to set the position of the 2nd op seaming roll to the chuck.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Re-tighten the lock nut on the 2nd operation seaming roller adjusting screw.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Re-tighten the hexagon setscrew.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
6.0 Change Over Procedure 6.1 Bottom guard plate assembly
Remove 3 button head socket screws.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Remove 6 button head socket screws.
Remove the bottom guard plate assembly.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
6.2 Seaming chuck
Use the pin spanner provided.
Locate the pin spanner in the hole on the seaming chuck boss.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Use a soft mallet to tap the pin spanner and loosen the seaming chuck.
Turn the driven pulley handle to rotate the chuck shaft.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Use your other hand to support the seaming chuck.
Reverse the procedure to fit the new seaming chuck.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
6.3 Seaming roll assembly
Locate the pin spanner in the hole on the seaming roll pin boss. Loosen the seaming roll pin lock nut.
Withdraw the seaming roll assembly through the hole in the seaming roller arm.
Reverse the procedure to fit a new seaming roll assembly.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
6.4 Change lifter spring
Remove the lifter plate.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Use the magnetic pick up tool supplied to extract the pressure cap.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Use the magnetic pickup tool again to remove the lifter spring and holder.
Drop in the new lifter spring, and replace the pressure cap and the lifter plate.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
7.0 Operation
With the machine running under power, place an end on top of the can. Place the can with the end on the lifter plate. Press both pneumatic actuating buttons simultaneously with each hand. The lifter plate will raise the can into the seaming head, and the seaming cycle will automatically initiate. Keep the actuating buttons depressed until the lifter comes down. Remove the seamed can and repeat the cycle.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
8.0 Maintenance & Cleaning
! Caution Isolate the power supply from the machine before cleaning, lubricating or
carrying out repairs
i Important Keep the work table of the machine permanently and perfectly clean
8.1 Cleaning
Guidelines for Wash Down
The preferred cleaning method is to wipe down the machine or to blow off with compressed air.
Follow the recommendations and instructions below to help prevent problems in environments where machinery is exposed to water during clean up:
! Caution To avoid injury, all power to the machine must be OFF before starting wash down
DO NOT apply the water stream directly on electrical components
Water pressure used to rinse the machine should be regulated to 5 psi maximum
Use open ended hose only
Use neutral cleaning solution (pH 6-8)
1. Turn off all power to the machine.
Use appropriate lockout procedures.
2. Ensure all openings to the electrical panel are sealed.
3. Cover all electrical enclosures, user interface and all motors with plastic or suitable material
before using any water on the machine.
4. Apply cleaning solution.
5. Use a soft brush or a plastic scraper to remove heavy deposits.
6. Rinse with clean water.
7. Remove excess water.
8. Allow machine to dry.
9. Remove plastic covers from electrical components.
10. Restore power to the machine.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
8.2 Lubrication
! Caution Isolate the power supply from the machine before lubricating
i Important Clean the machine before lubricating
Only use recommended lubricants
For operation in a dry fill production environment we recommend that all grease points are lubed after 12
hours of intermittent or continuous production.
In a wet fill environment all grease points should always be lubed immediately after the machine has been
washed and cleaned.
Lubrication Points
Chuck Spindle
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Seaming Lever Spindle / Lower Chuck Spindle Bearing
Seaming Lever Spindle
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
Recommended Lubricants
During manufacture the seamer is lubricated using Castrol Obeen FS 2 food grade grease. You should use
this lubricant for maintenance, or the equivalent grade of lubricant from an alternative reputable
manufacturer.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
9.0 CE Declaration of Conformity
12 February 2015 EC Declaration of Conformity
Machine Model 10A Semi Automatic Seamer
Machine Serial Number 8271
EC Directives Complied With Machinery Directive 2006/42/EC Low Voltage Directive 2006/95/EC Electromagnetic Compatibility Directive 2004/108/EC
Name and Address of Approved Body & Other Details, If Appropriate
Transposed Harmonised Standards Used
EN ISO 12100:2010 EN ISO 13849-2:2012 EN ISO 13850:2008 EN 1037:1995+A1:2008 EN ISO 4414:2010 BS EN 60204-1:2006 + A1:2009 EN61000-6-2:2005 EN 61000-6-4:2007 +A1:2011
We declare that the above machinery conforms to the relevant essential Health and Safety Requirements.
John P. Jenner, Director Eurocan Sales & Service Ltd, Unit B1 Newbrook Business Park
Pound Lane, Upper Beeding, BN44 3JD, U.K.
Eurocan Sales & Service Ltd
Tel: +44 (0)1903 810110 Email@ [email protected]
www.eurocanltd.com
10.0 Assembly and Parts Lists
900643 Seaming Head Frame Assembly
900661 Seaming Head Assembly
900696 Seaming Roll Assembly
900772 Pneumatic Lifter Assembly
900779 Pneumatic Trigger Assembly
900802 Can Lifter Plate Assembly
900805 Seaming Head Drive Assembly
900808 Knockout Assembly
900812 Seaming Head Guard Assembly
900813 Main Guard Enclosure Assembly
900820 Seaming Head Pneumatic Assembly
900946 Seamer Support Stand Assembly
900992 Electrical System
901126 Series 10 Seamer Tool List
10A 10A Change Parts Drawing
8271 Change Parts List 153 mm Diameter
8401 Change Parts List 99 mm Diameter
8421 Change Parts List 73 mm Diameter
Note: Change Parts are denoted in their assembly drawing by a 4 figure number eg. 0001.
See the Change Parts list for part numbers.
Assembly Name Seaming Head Frame Assembly
Assembly Number 900643
Item Number Part Number Part Name Quantity per Assembly
1 900645 Seaming head frame 1
2 900648 Seaming head clamp block RH 1
3 900823 Seaming head clamp block LH 1
4 900644 Seaming head guide RH 1
5 900824 Seaming head guide LH 1
6 900825 Seaming head central guide 1
7 900651 Leadscrew 1
8 900652 Leadscrew cap 1
9 900653 Leadscrew cap retainer 1
10 900654 Leadscrew nut 1
11 200208 Handwheel 1
12 200209 Handwheel Grip 1
13 200149 Hexagon head bolt 4
14 200154 Washer 4
15 200175 Socket head cap screw 8
16 200152 Socket head cap screw 2
17 200210 Socket Head Cap Screw 2
18 200119 Socket head cap screw 5
19 200211 Dowel Pin 8
20 200212 Dowel Pin 2
21 200130 Dowel pin 2
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Seaming Head Frame Assembly
Assembly Number 900643
Item Number Part Number Part Name Quantity per Assembly
22 200143 Socket head countersunk screw 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
SET U
P F
OR
350 M
M C
AN
1
21
42
41
7
811
27
28
33
34
45
45
46
47
46
47
ITEM
DESC
RIP
TIO
ND
RA
WIN
G N
UM
BER
QTY
1SEA
MIN
G H
EA
D
FR
AM
E A
SSEM
BLY
900643
1
2C
AN
LIF
TER
PLA
TE
ASSEM
BLY
900802
1
32N
D O
PER
ATIO
N
RO
LLER
AD
JU
STIN
G
SLEEV
E900668
1
41ST O
PER
ATIO
N
RO
LLER
AD
JU
STIN
G
SLEEV
E900659
1
5C
HU
CK
SH
AFT
SLEEV
E900666
1
6C
HU
CK
SH
AFT
900667
1
7SO
CK
ET H
EA
D C
AP
SC
REW
200152
6
8SO
CK
ET H
EA
D C
AP
SC
REW
200120
3
9SO
CK
ET H
EA
D C
AP
SC
REW
200119
1
10
OIL
ITE B
EA
RIN
G200132
3
11
OIL
ITE B
EA
RIN
G200131
1
12
1ST O
P R
OLLER
A
DJU
STIN
G A
RM
900660
1
13
RO
LLER
AR
M
WA
SH
ER
900726
2
14
CA
M R
OLLER
200137
2
15
DO
WEL P
IN200214
2
16
1ST O
PER
ATIO
N
RO
LLER
AD
JU
STIN
G
SH
AFT
900662
1
17
2N
D O
PER
ATIO
N
RO
LLER
AD
JU
STIN
G
SH
AFT
900663
1
18
PA
WL S
PIN
DLE
900722
1
19
TO
P P
AW
L900720
1
20
BO
TTO
M P
AW
L900721
1
21
SEA
MIN
G C
HU
CK
SEE C
HA
NG
E P
AR
TS
1
22
BA
LL B
EA
RIN
G200215
1
23
CH
UC
K S
HA
FT
BEA
RIN
G B
USH
900655
1
24
SEA
MIN
G C
AM
900656
1
25
CA
M D
RIV
E
SP
RO
CK
ET
900669
1
26
CA
M W
ASH
ER
900728
1
27
AD
JU
STIN
G S
CR
EW
200216
2
28
NU
T200142
2
29
EX
TER
NA
L C
IRC
LIP
200221
1
30
HEX
AG
ON
SC
REW
200163
2
31
HEX
AG
ON
SC
REW
M6 X
30
2
32
SP
RIN
G A
NC
HO
R
PIN
900730
2
33
WA
SH
ER
200217
2
34
SO
CK
ET H
EA
D C
AP
SC
REW
200145
2
35
CH
AIN
200151
1
36
TEN
SIO
N S
PR
ING
200133
1
37
EC
CEN
TR
IC B
USH
900725
1
38
CH
UC
K S
HA
FT B
USH
900822
1
39
LO
CK
NU
T200218
1
40
TA
B W
ASH
ER
200219
1
41
RO
LLER
AD
JU
STIN
G
LEV
ER
900665
2
42
SEA
MIN
G R
OLL
ASSEM
BLY
900696
2
43
RO
LLER
AR
M T
OP
W
ASH
ER
900727
2
44
2N
D O
P.
RO
LLER
A
DLU
STIN
G A
RM
900764
1
45
HO
USIN
G W
ASH
ER
200172
2
46
SH
AFT W
ASH
ER
200173
2
47
NEED
LE R
OLLER
C
AG
E200174
2
48
WA
SH
ER
200246
2
49
SLEEV
E6 X
12 X
10 L
ON
G2
50
OIL
ITE B
EA
RIN
G20 X
26 X
25
1
4
SEA
MIN
G H
EA
DA
SSEM
BLY
900661
31
/10
/11
AQ
UIL
A
WEIG
HT:
SEE P
AR
T L
IST
A1
SH
EET
1 O
F 2
SC
ALE:1
:2
DW
G N
O.
TITL
E:
REV
ISIO
ND
O N
OT S
CA
LE D
RA
WIN
G
MA
TER
IAL:
DA
TE
SIG
NA
TUR
EN
AM
E
DEB
UR
AN
D
BR
EA
K S
HA
RP
ED
GES
FIN
ISH
:U
NLESS O
THER
WIS
E S
PEC
IFIE
D:
DIM
EN
SIO
NS A
RE IN
MIL
LIM
ETE
RS
SU
RFA
CE F
INIS
H:
TOLER
AN
CES:
L
INEA
R:
A
NG
ULA
R:
Q.A
MFG
AP
PV
'D
CH
K'D
DR
AW
NA
PH
B B
AA
14
14
30
32
32
36
15
56
91918
20
SEC
TIO
N B
-B
50
10
10
10
4
312
44
13
13
16
17
43
43
49
31
48
31
48
49
SEC
TIO
N A
-A
22
23
24 25
26
29
37
39
40 38
35
4
SEA
MIN
G H
EA
DA
SSEM
BLY
900661
24
/0
9/1
2A
QU
ILA
WEIG
HT:
SEE P
AR
T L
IST
A1
SH
EET 2
OF 2
SC
ALE:1
:2
DW
G N
O.
TITL
E:
REV
ISIO
ND
O N
OT S
CA
LE D
RA
WIN
G
MA
TER
IAL:
DA
TE
SIG
NA
TUR
EN
AM
E
DEB
UR
AN
D
BR
EA
K S
HA
RP
ED
GES
FIN
ISH
:U
NLESS O
THER
WIS
E S
PEC
IFIE
D:
DIM
EN
SIO
NS A
RE IN
MIL
LIM
ETE
RS
SU
RFA
CE F
INIS
H:
TOLER
AN
CES:
L
INEA
R:
A
NG
ULA
R:
Q.A
MFG
AP
PV
'D
CH
K'D
DR
AW
N
Assembly Name Seaming Head Assembly
Assembly Number 900661
Item Number Part Number Part Name Quantity per Assembly
1 900643 Seaming head frame assembly 1
2 900802 Can lifter plate assembly 1
3 900668 1st op roller adjusting sleeve 1
4 900659 2nd op roller adjusting sleeve 1
5 900666 Chuck shaft sleeve 1
6 900667 Chuck shaft 1
7 200152 Socket head cap screw 6
8 200120 Socket head cap screw 3
9 200119 Socket head cap screw 1
10 200132 Oilite bearing 3
11 200131 Oilite bearing 1
12 900660 2nd op roller adjusting arm 1
13 900726 Roller arm washer 2
14 200137 Cam roller 2
15 200214 Dowel pin 2
16 900662 2nd op roller adjusting shaft 1
17 900663 1st op roller adjusting shaft 1
18 900722 Pawl spindle 1
19 900720 Top pawl 1
20 900721 Bottom pawl 1
21 0001 Seaming Chuck 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Seaming Head Assembly
Assembly Number 900661
Item Number Part Number Part Name Quantity per Assembly
22 200215 Ball Bearing 1
23 900655 Chuck shaft bearing bush 1
24 900656 Seaming cam 1
25 900669 Cam drive sprocket 1
26 900728 Cam washer 1
27 200216 Adjusting Screw 2
28 200142 Nut 2
29 200221 External Circlip 1
30 200163 Heaxagon Set Screw 2
31 900729 Roller arm shaft pin 2
32 900730 Spring anchor pin 2
33 200217 Washer 2
34 200145 Socket head cap screw 2
35 200151 Roller chain 1
36 200133 Tension spring 1
37 900725 Eccentric bush 1
38 900822 Chuck shaft bush 1
39 200218 Lock Nut 1
40 200219 Tab Washer 1
41 900665 Roller adjusting lever 2
42 900696 Seaming roll assembly 2
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Seaming Head Assembly
Assembly Number 900661
Item Number Part Number Part Name Quantity per Assembly
44 900764 1st op roller adjusting arm 1
45 200172 Housing Washer 2
46 200173 Shaft Washer 2
47 200174 Needle Roller Cage 2
48 901089 Chuck shaft bush 1
49 200372 Sleeve 2
50 200371 Oilite bearing 1
51 200141 Grease nipple 2
52 200148 Socket set screw 3
53 200385 Flanged Oilite Bearing 1
54 200144 Connecting link 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
USE
HOO
K W
REN
CH
40 Z
45-
50 T
OA
SSEM
BLE
ROLL
PIN
TO
RO
LL P
INLE
VER
ARM
AA
SEC
TION
A-A
3 2 1 4 5
6 6
ITEM
NO
.PA
RT N
UMBE
RD
ESC
RIPT
ION
QTY
.1
9006
99SE
AM
ING
RO
LL1
290
0697
SEA
MIN
G R
OLL
PIN
13
M20
x 1
.5 L
ockn
utM
20 x
1.5
LO
CKN
UT1
432
03_A
_2RS
1TN
9_M
T33
HIH
IA
NG
ULA
R C
ON
TAC
T BA
LL
BEA
RIN
G, D
OUB
LE R
OW
, SEA
L O
N B
OTH
SID
ES1
590
0698
SEA
MIN
G R
OLL
PIN
EN
D C
AP
1
6Sp
ringm
aste
rs
Inte
rnal
Circ
lip
INT0
400
CIR
CLI
P - I
NT0
400
2
6
DCBA E F G H
EA B C D F
54
32
17
89
1011
12
12
34
56
78
G
PREL
IMIN
ARY
SEA
MIN
G R
OLL
ASS
EMBL
Y90
0696
17/0
5/12
AQ
UILA
WEI
GHT
:
SEE
ITEM
LIS
TA
2
SHEE
T 1 O
F 1
SCA
LE:1
:1
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
Assembly Name Seaming Roll Assembly
Assembly Number 900696
Item Number Part Number Part Name Quantity per Assembly
1 0002 / 0003 Seaming Roll 2
2 900697 Seaming roll pin 1
3 200134 Lock Nut 1
4 200160 Ball bearing 1
5 900698 Seaming roll pin end cap 1
6 200161 Internal Circlip 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Pneumatic Lifter Assembly
Assembly Number 900772
Item Number Part Number Part Name Quantity per Assembly
1 900767 Split Block for Pneumatic Cylinder 1
2 900768 Split threaded bush 1
3 900770 Lifter shaft sleeve pneumatic lift 1
4 900771 Cylinder Rod Pin 1
5 200175 Socket head cap screw 2
6 200162 Circlip 2
7 200176 Pneumatic cylinder 1
8 200164 Oilite Bearing 2
9 200182 Lifter Washer 1
10 200267 Lifter rod clevis
11 200268 Lifter cylinder bracket
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Pneumatic Trigger Assembly
Assembly Number 900779
Item Number Part Number Part Name Quantity per Assembly
1 200177 Pneumatic cylinder 1
2 900784 Actuating arm 1
3 900783 Trigger cylinder bracket 1
4 900782 Return stop bracket 1
5 900781 Forward stop bracket 1
6 900780 Cylinder rod clevis 1
7 200163 Heaxagon Set Screw 2
8 200178 Lock nut 2
9 200120 Socket head cap screw 6
10 200156 Socket head cap screw 1
11 200206 Socket head cap screw 1
12 200207 Nyloc nut 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
2 1 5 10 12 6 8 119
43
7
ITEM
NO
.PA
RT N
UMBE
RD
ESC
RIPT
ION
QTY
.1
9006
57LI
FTER
PLA
TE S
HAFT
12
9006
58LI
FTER
PLA
TE1
320
0101
SOC
KET
HEA
D C
OUN
TERS
UNK
SCRE
W1
420
0102
DO
WEL
PIN
15
9008
03LI
FTER
PLA
TE S
HAFT
BUS
H1
620
0103
SPRI
NG
HO
LDER
17
2001
04SP
RIN
G W
ASH
ER1
820
0105
PRES
SURE
AD
JUST
ING
NUT
19
2001
06LI
FTER
SPR
ING
110
2001
07PR
ESSU
RE S
TUD
111
9007
69LI
FTER
SHA
FT1
1220
0108
PRES
SURE
CA
P1
PREL
IMIN
ARY
CA
N L
IFTE
R PL
ATE
ASS
EMBL
Y90
0802
12/0
3/13
AQ
UILA
WEI
GHT
:
SEE
ITEM
LIS
TA
2
SHEE
T 1 O
F 1
SCA
LE:1
:2
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
APH
Assembly Name Can Lifter Plate Assembly
Assembly Number 900802
Item Number Part Number Part Name Quantity per Assembly
1 900657 Lifter plate shaft 1
2 0005 Lifter plate 1
3 200101 Socket head countersunk screw 1
4 200102 Dowel pin 1
5 900803 Lifter plate shaft bush 1
6 200103 Spring holder 1
7 200104 Spring washer 1
8 200105 Pressure adjusting nut 1
9 200106 Lifter spring 1
10 200107 Pressure stud 1
11 900769 Lifter shaft 1
12 200108 Pressure cap 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Seaming Head Drive Assembly
Assembly Number 900805
Item Number Part Number Part Name Quantity per Assembly
1 200200 Drive Motor 1
2 200201 Motor Slide Base 1
3 900731 Motor Mounting Bracket 1
4 200166 V Pulley 1
5 200168 Taperlock Bush 1
6 200167 V Pulley 1
7 200169 Taperlock Bush 1
8 200199 Revolving Handle 1
9 200165 V Belt 2
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
A ASE
CTIO
N A
-A1
5
4
3 7 2
6
ITEM
NO
.PA
RT N
UMBE
RD
ESC
RIPT
ION
QTY
190
0809
KNO
CK-
OUT
BUS
H1
290
0810
KNO
CK-
OUT
PA
D1
390
0811
KNO
CK-
OUT
SHA
FT1
420
0202
CIR
CLI
P1
5SP
RIN
GM
AST
ERS
C66
0939
0 1
620
0204
ROLL
ER B
EARI
NG
17
2002
05SO
CKE
T HE
AD
CSK
SC
REW
1 1
KNO
CK-
OUT
ASS
EMBL
Y90
0808
03/0
5/13
AQ
UILA
WEI
GHT
:
SEE
ITEM
LIS
TA
3
SHEE
T 1 O
F 1
SCA
LE:1
:1
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
AQ
UILA
Assembly Name Knockout Assembly
Assembly Number 900808
Item Number Part Number Part Name Quantity per Assembly
1 900809 Knockout bush 1
3 900811 Knockout shaft Rev 2 1
4 200202 Circlip 1
5 200262 Knock-out Spring 1
6 200204 Roller bearing 1
7 200205 Socket head countersunk screw 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Seaming Head Guard Assembly
Assembly Number 900812
Item Number Part Number Part Name Quantity per Assembly
1 900813 Main guard enclosure assembly 1
2 900815 Bottom guard plate assembly 153 mm dia 1
3 900817 Top guard plate 1
4 900818 Front guard plate 1
5 200242 Socket Button Head Screw 24
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Main Guard Enclosure Assembly
Assembly Number 900813
Item Number Part Number Part Name Quantity per Assembly
1 900814 Main Guard Enclosure 1
2 200224 Self clinching nut 21
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
118.10
130.68
400
.00
454
.00
290
.00
220.00 55.00
4 O
FF M
OUN
TING
HO
LES
6.50
300
.00
V1V2
INLET
D ECBA
32
15
C D
46
78
A B
F
E
FOR
EST
RO
W B
USI
NES
S PA
RK
STA
TIO
N R
OA
DFO
RES
T R
OW
RH
18 5
DW
P80-
056-
350
DES
DR
CK
DA
TETB
01 J
uly
2014
CA
DD
RA
WIN
GD
WG
SIZE
A3
SHEE
TO
F
SCA
LE1:
5
MA
TER
IAL
AN
D S
PEC
IFIC
ATI
ON
FIN
ISH
ESTI
MA
TED
WEI
GH
T
RA
W.
FIN
.
USE
D O
N
REV
.No.
E.R.
No.
BY
DA
TE0
0000
TB10
JUN
14U
NSP
ECIF
IED
AN
D B
S 30
8 TO
LER
AN
CES
WO
RK
S O
RD
ER N
o.W
EEK
No.
QTY
.
DIM
ENSI
ON
S IN
MIL
LIM
ETR
ESD
UA
L D
IMEN
SIO
NS
IN [I
NC
HES
]
REM
OV
E B
UR
RS
AN
D S
HA
RP
EDG
ES U
NLE
SS S
TATE
D
THIR
D A
NG
LE P
RO
JEC
TIO
N
DO
NO
T SC
ALE
THIS
DR
AW
ING
IS T
HE
PRO
PER
TY O
F A
IR
ENG
INEE
RIN
G L
TD.
IT M
UST
NO
T B
E C
OPI
ED,
USE
D F
OR
MA
NU
FAC
TUR
EO
R D
ISC
LOSE
D W
ITH
OU
TTH
E PR
IOR
WR
ITTE
NC
ON
SEN
T O
F TH
E C
OM
PAN
Y
1 PL
AC
E
2 PL
AC
ESSU
RFA
CE
FIN
ISH
AN
GLE
S
RO
UN
DN
ESS
0.0
0.00
FLA
TNES
S
PAR
ALL
ELIS
M
RU
N O
UT
SQU
AR
ENES
S
CO
NC
ENTR
ICIT
Y0.
01
0.25
0.10
1.6
Ra
1/2
0.01
EXP.
No.
DW
G.N
o.P8
0-05
6-35
0
13
Con
trol P
anel
- Eu
roca
n Sy
stem
CS
109
13
124
15 6 11
2018
16
77 13
1713
214251413 8
8
2221
19
ITEM
NO
.PA
RT N
UMBE
RD
ESC
RIPT
ION
Def
ault/
QTY
.1
KL 1
530.
010
Encl
osur
e 40
0 x
300
x 12
0 St
/Ste
el1
2P
520
501
GV
alv
e 1/
8" 5
/2 P
ilot/
Pilo
t (D
ual U
se)
2
3BA
311
201
Va
lve
3/2
M5
2
4BA
221
03
Push
But
ton
Gre
en2
578
18-0
4-10
Pneu
mat
ic S
enso
r Fiti
ng 1
/8"
1
678
18-0
4-13
Pneu
mat
ic S
enso
r Fiti
ng 1
/4"
2
770
50 1
-41/
4" E
xha
ust F
low
Con
trol
2
870
50 1
-81/
8" E
xha
ust F
low
Con
trol
2
9PM
1206
EBu
lkhe
ad 6
mm
2
10PM
1210
EBu
lkhe
ad 1
0mm
311
P 51
0 70
1V
alv
e 1/
4" 5
/2 P
ilot/
Air
Sprin
g1
1231
01-0
4-19
M5
x 4m
m S
traig
ht F
ittin
g4
13RP
7218
04Sw
ivel
Elb
ow 4
mm
x G
1/8"
7
14RP
7218
06Sw
ivel
Elb
ow 6
mm
x G
1/8"
4
15RP
7214
10Sw
ivel
Elb
ow 1
0mm
x G
1/4"
3
1607
020
1-2
Sile
ncer
- 1/
2" B
SP1
1707
020
1-8
Sile
ncer
1/8
" BSP
218
RP51
1804
Stra
ight
Ad
apto
r 4m
m x
G1/
8"
6
1902
096
1-2
Nut
1/2
" BSP
120
KI 3
10 5
02V
avl
e - 1
/8"3
/2 T
wo
Ha
nd/S
prin
g1
2181
5069
40Tim
er N
C 0
.1-1
5 se
cs1
2281
532
104
Base
- Tim
er1
23RM
0204
EEq
ual T
ee C
onne
ctor
4m
m5
24RM
0210
EEq
ual T
ee C
onne
ctor
10m
m1
25PM
0610
06E
Red
ucer
10m
m -
6mm
126
PM02
06E
Equa
l Tee
Con
nect
or 6
mm
2
27PM
0606
04E
Red
ucer
6m
m -
4mm
1
D ECBA
32
15
C D
46
78
A B
F
E
FOR
EST
RO
W B
USI
NES
S PA
RK
STA
TIO
N R
OA
DFO
RES
T R
OW
RH
18 5
DW
P80-
056-
350
DES
DR
CK
DA
TETB
29 M
ay 2
014
CA
DD
RA
WIN
GD
WG
SIZE
A3
SHEE
TO
F
SCA
LE1:
5
MA
TER
IAL
AN
D S
PEC
IFIC
ATI
ON
FIN
ISH
ESTI
MA
TED
WEI
GH
T
RA
W.
FIN
.
USE
D O
N
REV
.No.
E.R.
No.
BY
DA
TE0
0000
TB10
JUN
14U
NSP
ECIF
IED
AN
D B
S 30
8 TO
LER
AN
CES
WO
RK
S O
RD
ER N
o.W
EEK
No.
QTY
.
DIM
ENSI
ON
S IN
MIL
LIM
ETR
ESD
UA
L D
IMEN
SIO
NS
IN [I
NC
HES
]
REM
OV
E B
UR
RS
AN
D S
HA
RP
EDG
ES U
NLE
SS S
TATE
D
THIR
D A
NG
LE P
RO
JEC
TIO
N
DO
NO
T SC
ALE
THIS
DR
AW
ING
IS T
HE
PRO
PER
TY O
F A
IR
ENG
INEE
RIN
G L
TD.
IT M
UST
NO
T B
E C
OPI
ED,
USE
D F
OR
MA
NU
FAC
TUR
EO
R D
ISC
LOSE
D W
ITH
OU
TTH
E PR
IOR
WR
ITTE
NC
ON
SEN
T O
F TH
E C
OM
PAN
Y
1 PL
AC
E
2 PL
AC
ESSU
RFA
CE
FIN
ISH
AN
GLE
S
RO
UN
DN
ESS
0.0
0.00
FLA
TNES
S
PAR
ALL
ELIS
M
RU
N O
UT
SQU
AR
ENES
S
CO
NC
ENTR
ICIT
Y0.
01
0.25
0.10
1.6
Ra
1/2
0.01
EXP.
No.
DW
G.N
o.P8
0-05
6-35
0
23
Con
trol P
anel
- Eu
roca
n Sy
stem
CS
0
15.
00
26.
25
45.
00
55.
00
72.
00
75.
00
85.
00
110
.00
118
.00
145
.00
172
.00
230
.00
275
.00
0
55.00
90.00 85.00
116.00 111.25 105.00
140.00
200.00
260.00
295.00 290.00
315.00
345.00 AAA A
AA
B
B BB
C
C
C
C
DD
DE
E
D
50.00
50.
00
22
.00
Hole
Dia
met
er
A6.
5B
5.5
C4.
5D
21E
16
D ECBA
32
15
C D
46
78
A B
F
E
FOR
EST
RO
W B
USI
NES
S PA
RK
STA
TIO
N R
OA
DFO
RES
T R
OW
RH
18 5
DW
P80-
056-
350
DES
DR
CK
DA
TECS
29 M
ay 2
014
CA
DD
RA
WIN
GD
WG
SIZE
A3
SHEE
TO
F
SCA
LE1:
2
MA
TER
IAL
AN
D S
PEC
IFIC
ATI
ON
FIN
ISH
ESTI
MA
TED
WEI
GH
T
RA
W.
FIN
.
USE
D O
N
REV
.No.
E.R.
No.
BY
DA
TE0
0000
TB10
JUN
14U
NSP
ECIF
IED
AN
D B
S 30
8 TO
LER
AN
CES
WO
RK
S O
RD
ER N
o.W
EEK
No.
QTY
.
DIM
ENSI
ON
S IN
MIL
LIM
ETR
ESD
UA
L D
IMEN
SIO
NS
IN [I
NC
HES
]
REM
OV
E B
UR
RS
AN
D S
HA
RP
EDG
ES U
NLE
SS S
TATE
D
THIR
D A
NG
LE P
RO
JEC
TIO
N
DO
NO
T SC
ALE
THIS
DR
AW
ING
IS T
HE
PRO
PER
TY O
F A
IR
ENG
INEE
RIN
G L
TD.
IT M
UST
NO
T B
E C
OPI
ED,
USE
D F
OR
MA
NU
FAC
TUR
EO
R D
ISC
LOSE
D W
ITH
OU
TTH
E PR
IOR
WR
ITTE
NC
ON
SEN
T O
F TH
E C
OM
PAN
Y
1 PL
AC
E
2 PL
AC
ESSU
RFA
CE
FIN
ISH
AN
GLE
S
RO
UN
DN
ESS
0.0
0.00
FLA
TNES
S
PAR
ALL
ELIS
M
RU
N O
UT
SQU
AR
ENES
S
CO
NC
ENTR
ICIT
Y0.
01
0.25
0.10
1.6
Ra
1/2
0.01
EXP.
No.
DW
G.N
o.D
EFA
ULT
33
TB
Con
trol P
anel
- Eu
roca
n Sy
stem
Assembly Name Seaming Head Pneumatic Assembly
Assembly Number 900820
Item Number Part Number Part Name Quantity per Assembly
1 200289 Control panel 1
2 200290 Shut off valve 1
3 200291 Filter 1
4 200292 Gauge 1
5 200293 Swivel elbow 2
6 200294 Swivel elbow 2
7 200295 Polyurethane tube 1
8 200296 Polyurethane tube 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
Assembly Name Seamer Support Stand Assembly
Assembly Number 900946
Item Number Part Number Part Name Quantity per Assembly
1 900723 Seamer Support Stand 1
2 200236 Levelling Foot 4
3 200252 Nut 4
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
DRI
VE
MR-
J3-2
00A
4
L1L1 L2
ISO
LATO
R
SERV
O M
OTO
R
UV
W
L3 NNL3L2L1
NL3L2
L1L2
L3
CSM
CB1
45
6
4240
MC
B5 12
MITS
UBIS
HI
FX3U
- 32
M
L1N
78
9
5152
53
L21
57
L11
56
L1N
MC
B2M
CB3
MC
B4
240
AC
24V
DC
PSU
+24V
0V
11
SEA
MER
MO
TOR
HART
ING
PLUG
CO
NN
ECTIO
N
10N
CH
CH 41
1
MO
DEL
100
LIN
EAR
SEA
MER
ELE
CTR
ICA
LC
IRC
UIT
9009
92
DEC
11
AQ
UILA
WEI
GHT
:
A2
SHEE
T 1
OF
3SC
ALE
N.T
.S.
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
APH
11
CS
RESE
TSA
FETY
CO
NTA
CTO
R
MC
B625
11 24
26
PNO
Z X
7SA
FETY
REL
AY
A1
1323 24
14A
2
Y1 Y2
2425
CS
RESE
T
RIG
HT
REA
RLI
MIT
SW.
LEFT
REA
RLI
MIT
SW.
LEFT
FRO
NT
LIM
IT SW
.
RIG
HT F
RON
TLI
MIT
SW.
RIG
HT F
RON
TE/
STO
P
LEFT
FRO
NT
E/ST
OP
LEFT
REA
RE/
STO
P
RIG
HT
REA
RE/
STO
P
241
242
243
245
246
247
244
1
MO
DEL
100
LIN
EAR
SEA
MER
ELE
CTR
ICA
LC
IRC
UIT
9009
92
DEC
11
AQ
UILA
WEI
GHT
:
A2
SHEE
T 2
OF
3SC
ALE
: N.T
.S
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
APH
2411
24
SEA
MER
HEA
D S
OL
11
VV
OV
X0X1
6X1
4X1
2X1
0X6
X4X2
24V
X1X3
X5X7
X11
X13
X15
X17
Y16
Y17
Y15
Y14
Y13
Y12
Y11
Y10
Y7
Y6
Y5
Y4
Y3Y1
Y2Y0
CO
M1
CO
M2
CO
M3
CO
M 4
CH
14
CS
PAN
EL V
IEW
+24V
PE0V
RS48
5C
OM
SC
ABL
E
MITS
UBIS
HI F
X3U
- 32M
MC
B7
25
E/STOP CCT
START
STOPLID MAG LEVEL
POST SEAM
PRE SEAM
LIFT DOWN
LIFT UP
TURRET BACK
TURRET FWD
CAN PRESENT
LID FEED FWD
LID FEED BACK
CHAIN INDEX
SERVO FAULT
SERVO READY
CHAIN FWD
CHAIN REVERSE
SERVO ON
RESET SERVO
CAN LIFT SOL
SEAM TRIGGER SOL
LID FEED SOL
TURR
ETIN
DEX
SO
L
1
MO
DEL
100
LIN
EAR
SEA
MER
ELE
CTR
ICA
LC
IRC
UIT
9009
92W
EIG
HT:
A2
SHEE
T 3
OF
3SC
ALE
:1:1
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
Assembly Name Series 10 Seamer Tool List
Assembly Number 901126
Item Number Part Number Part Name Quantity per Assembly
1 200314 Flexible magnetic pick up tool 1
2 200199 Revolving Handle 1
3 200365 Pin spanner 1
Eurocan Sales & Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com
ITEM
000
1ITE
M 0
004
ITEM
000
5
ITEM
000
6
ITEM
000
2ITE
M 0
003
N/A
10A
CHA
NG
E PA
RTS
08/0
9/14
AQ
UILA
WEI
GHT
:
N/A
A3
SHEE
T 1 O
F 1
SCA
LE:1
:2
DW
G N
O.
TITLE
:
REVI
SIO
ND
O N
OT
SCA
LE D
RAW
ING
MA
TERI
AL:
DA
TESI
GN
ATU
REN
AM
E
DEB
UR A
ND
BR
EAK
SHA
RP
EDG
ES
FINIS
H:UN
LESS
OTH
ERW
ISE
SPEC
IFIE
D:
DIM
ENSI
ON
S A
RE IN
MILL
IMET
ERS
SURF
AC
E FI
NIS
H:TO
LERA
NC
ES:
LIN
EAR:
A
NG
ULA
R:
Q.A
MFG
APP
V'D
CHK
'D
DRA
WN
Item Number Part Number Part Description Quantity
0001 900785 Seaming Chuck 153mm Dia NEO 1
0002 900699 R27 1st Op. Seaming Roll 1
0003 900699 SRG286 2nd Op. Seaming Roll 1
0004 900810 Knockout Pad 153mm Dia NEO 1
0005 900786 Lifter Plate 153mm Dia Over Cap 1
0006 900815 Bottom Guard Plate Assembly 153mm Dia 1
8271 Change Parts 153mm Diameter
Item Number Part Number Part Description Quantity
0001 900826 Seaming Chuck 99mm Dia NEO 1
0002 900699 1600155 1st Op. Seaming Roll 1
0003 900699 1600156 2nd Op. Seaming Roll 1
0004 900827 Knockout Pad 99mm Dia NEO 1
0005 900828 Lifter Plate 99mm Dia NEO 1
0006 900835 Bottom Guard Plate Assembly 99mm Dia 1
8401 Change Parts 99mm Diameter
Item Number Part Number Part Description Quantity
0001 900700 Seaming Chuck 73mm Dia NEO 1
0002 900699 12050 1st
Op. Seaming Roll 1
0003 900699 12051 2nd
Op. Seaming Roll 1
0004 900885 Knockout Pad 73mm Dia NEO 1
0005 900886 Lifter Plate 73mm Dia NEO 1
0006 900890 Bottom Guard Plate Assembly 73mm Dia 1
8421 Change Parts 73mm Diameter
Sales & Service LtdEUROCAN
Eurocan Sales and Service LtdTel: +44 (0)1903 810110 Email: [email protected]
www.eurocanltd.com