Poles & ArmsAluminum Poles SNTA 4 - 4" Square Non-Tapered Aluminum 21 SNTA 5 - 5" Square Non-Tapered...
Transcript of Poles & ArmsAluminum Poles SNTA 4 - 4" Square Non-Tapered Aluminum 21 SNTA 5 - 5" Square Non-Tapered...
Poles & ArmsStructural Integrity in Steel and Aluminum
Steel Poles
INDEX
SNTS 4 - 4" Square Non-Tapered Steel 1SNTS 5 - 5" Square Non-Tapered Steel 3SNTS 6 - 6" Square Non-Tapered Steel 5
STS - Square Tapered Steel 7
RNTS 4 - 4" Round Non-Tapered Steel 9RNTS 5 - 5" Round Non-Tapered Steel 11RNTS 55/8 - 55/8" Round Non-Tapered Steel 13RNTS 6 - 6" Round Non-Tapered Steel 15RNTS 65/8 - 65/8" Round Non-Tapered Steel 17
RTS - Round Tapered Steel 19
Aluminum Poles
SNTA 4 - 4" Square Non-Tapered Aluminum 21SNTA 5 - 5" Square Non-Tapered Aluminum 23SNTA 6 - 6" Square Non-Tapered Aluminum 25
SNTAR 4 - 4" Square Non-Tapered Rounded Aluminum 27 SNTAR 5 - 5" Square Non-Tapered Rounded Aluminum 29SNTAR 6 - 6" Square Non-Tapered Rounded Aluminum 31
RNTA 4 - 4" Round Non-Tapered Aluminum 33RNTA 5 - 5" Round Non-Tapered Aluminum 35RNTA 55/8 - 55/8" Round Non-Tapered Aluminum 37RNTA 6 - 6" Round Non-Tapered Aluminum 39RNTA 65/8 - 65/8" Round Non-Tapered Aluminum 41
RTA - Round Tapered Aluminum 43
Arms 45
Accessories 50
Terms and Condition of Sale 52
Isotach Wind Map 54
U.S. ARCHITECTURAL LTG. www.usaltg.com
18"HandHole
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Square Straight SteelSNTS 4"
Specifications
Pole Top Mount Hand Hole Cover
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Reinforced hand holewith tamper resistant bolt assembly
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
Shaft - 4" square, fabricated from high grade structural steel tube. Shaft conforms
to ASTM-A-501-68 specifications. Meets or exceeds minimum yield strength of
46,000 P.S.I. Wall thickness 11 GA. (.120 wall) or 7 GA. (.180 wall) as specified.
Reinforced hand hole is furnished with cover. Shaft is furnished with ground lug
located inside pole on wall opposite hand hole.
8" - 11" Dia. Bolt Circle
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Reinforcing welded bracket
Locking bar
Hand hole cover
Tamper resistantscrew
Height
4"
U.S. ARCHITECTURAL LTG.www.usaltg.com 1
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTS 104 - 11
SNTS 124 - 11
SNTS 144 - 11
SNTS 154 - 11
SNTS 164 - 11
SNTS 184 - 11
SNTS 204 - 11
SNTS 204 - 7
SNTS 254 - 11
SNTS 254 - 7
10'
12'
14'
15'
16'
18'
20'
20'
25'
25'
11
11
11
11
11
11
11
7
11
7
9"
9"
9"
9"
9"
9"
10"
11"
11"
11"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X24"X3"
¾"X30"X3"
¾"X24"X3"
¾"X30"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
33.4
25.8
20.2
17.9
15.9
13.8
11.6
17.4
8.8
11.2
26.1
20.4
16.1
14.4
12.8
10.1
7.9
14.0
5.5
9.1
20.5
16.1
12.8
11.4
10.1
8.2
6.2
11.3
3.2
6.1
16.7
12.2
9.9
8.9
7.9
6.2
4.8
8.8
1.6
4.3
400
400
400
400
400
400
400
450
350
450
SNTS 104 - 11
SNTS 124 - 11
SNTS 144 - 11
SNTS 154 - 11
SNTS 164 - 11
SNTS 184 - 11
SNTS 204 - 11
SNTS 204 - 7
SNTS 254 - 11
SNTS 254 - 7
0º
180º
SNTS 4"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
POLE MODEL NUMBER - SNTS 4" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com2
Height
5"
Square Straight SteelSNTS 5"
Specifications
Pole Top Mount Hand Hole Cover
Reinforced hand holewith tamper resistant bolt assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
Shaft - 5" square, fabricated from high grade structural steel tube. Shaft conforms
to ASTM-A-501-68 specifications. Meets or exceeds minimum yield strength of
46,000 P.S.I. Wall thickness 11 GA. (.120 wall) or 7 GA. (.180 wall) as specified.
Reinforced hand hole is furnished with cover. Shaft is furnished with ground lug
located inside pole on wall opposite hand hole.
10½" - 12½" Dia.Bolt Circle
Two Piece Base Cover Assembly
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Reinforcing welded bracket
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 3
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTS 185 - 11
SNTS 205 - 11
SNTS 205 - 7
SNTS 255 - 11
SNTS 255 - 7
SNTS 305 - 11
SNTS 305 - 7
SNTS 355 - 7
18'
20'
20'
25'
25'
30'
30'
35'
11
11
7
11
7
11
7
7
11½"
11½"
11½"
11½"
11½"
11½"
11½"
11½"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
27.0
23.3
31.2
14.6
23.8
7.5
18.2
14.9
20.2
16.6
25.1
9.8
17.0
5.7
12.1
9.3
14.5
12.0
19.2
6.5
12.4
2.8
8.7
5.2
10.9
8.6
15.7
5.1
9.4
N/A
5.6
2.5
400
400
450
400
400
350
375
350
SNTS 185 - 11
SNTS 205 - 11
SNTS 205 - 7
SNTS 255 - 11
SNTS 255 - 7
SNTS 305 - 11
SNTS 305 - 7
SNTS 355 - 7
SNTS 5"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTS 5" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com4
Height
6"
Square Straight SteelSNTS 6"
Pole Top Mount Hand Hole Cover
Reinforced hand holewith tamper resistant bolt assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
Shaft - 6" square, fabricated from high grade structural steel tube. Shaft conforms
to ASTM-A-501-68 specifications. Meets or exceeds minimum yield strength of
46,000 P.S.I. Wall thickness 11 GA. (.120 wall) or 7 GA. (.180 wall) as specified.
Reinforced hand hole is furnished with cover. Shaft is furnished with ground lug
located inside pole on wall opposite hand hole.
Two Piece Base Cover Assembly
11½" - 14½" Dia.Bolt Circle
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Reinforcing welded bracket
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 5
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTS 206 - 7
SNTS 256 - 7
SNTS 306 - 7
SNTS 356 - 7
SNTS 406 - 7
20'
25'
30'
35'
40'
7
7
7
7
7
11½"
11½"
11½"
13½"
13½"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
COUPLING
RECEPTACLE
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
52.1
37.1
29.5
20.9
14.3
34.3
29.2
20.8
13.6
9.4
26.2
21.8
14.5
6.7
5.4
21.9
14.7
9.8
4.9
2.5
400
400
400
400
400
SNTS 206 - 7
SNTS 256 - 7
SNTS 306 - 7
SNTS 356 - 7
SNTS 406 - 7
Engineering DataMaximum EPA - Square Feet
SNTS 6"
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTS 6" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com6
Height
Square Tapered SteelSTS
Specifications
Pole Top Mount Hand Hole Cover
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
Shaft - One piece construction fabricated from coil stock. Weldable grade. Hot
rolled commercial quality carbon steel. Guaranteed minimum yield strength
55,000 P.S.I. Shaft has uniform taper of approximately .14" per foot. Wall thickness
11 GA. (.120 wall) or 7 GA. (.180 wall) as specified. Flush reinforced hand hole is
furnished with cover. Shaft is furnished with ground lug located inside pole on wall
opposite hand hole.
Bolt Circle(See Ordering Specs.
under Poles)
Tenon
Pole Top Plate
Pole Shaft
Reinforced hand holewith tamper resistant bolt assembly
BoltProjection
18"HandHole
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:
(Consult Factory)
Reinforcing welded bracket
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 7
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
STS 20 - 11
STS 25 - 11
STS 30 - 11
20'
25'
30'
11
11
11
5.3X3.0
6.0X3.3
6.4X3.0
11½"
11½"
13½"
1"X36"X4"
1"X36"X4"
1"X36"X4"
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
SPECIFY OTHER HEIGHTS
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
15.4
14.9
12.6
11.2
10.9
8.6
8.4
7.8
5.9
6.3
5.8
4.0
275
275
225
STS 20 - 11
STS 25 - 11
STS 30 - 11
POLEHEIGHT
SHAFTSIZE
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
STS
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - STS MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com8
Height
4"
Round Straight SteelRNTS 4"
Pole Top Mount Hand Hole Cover
8" - 11" Dia.Bolt Circle
Two Piece Base Cover Assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Shaft - 4" diameter, fabricated from high grade structural steel tube. Shaft conforms
to ASTM-A-501-68 specifications. Meets or exceeds minimum yield strength of
46,000 P.S.I. Wall thickness 11GA. (.120 wall) or 7 GA. (.180 wall) as specified.
Reinforced hand hole is furnished with cover. Shaft is furnished with ground lug
located inside pole on wall opposite hand hole.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
Locking bar
Hand hole cover
Tamper resistantscrew
Locking bar
Hand hole cover
Tamper resistantscrew
Reinforcing welded bracket
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Below 15' - Hand hole cover withtamper resistant bolt assembly
15' and up - Reinforced hand holewith tamper resistant bolt assembly
U.S. ARCHITECTURAL LTG.www.usaltg.com 9
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTS 104 - 11
RNTS 124 - 11
RNTS 144 - 11
RNTS 164 - 11
RNTS 184 - 11
RNTS 204 - 11
RNTS 204 - 7
RNTS 244 - 7
10'
12'
14'
16'
18'
20'
20'
24'
11
11
11
11
11
11
7
7
9"
9"
9"
9"
9"
10"
10"
11"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X24"X3"
¾"X24"X3"
¾"X30"X3"
¾"X30"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
20.9
17.2
11.9
11.2
9.0
7.2
18.6
13.1
17.8
14.5
10.8
9.3
7.5
6.0
14.8
8.9
14.7
11.7
9.0
7.2
5.8
4.4
10.2
5.8
12.0
9.3
7.5
5.8
4.6
3.6
6.8
3.2
225
165
135
110
100
100
135
110
RNTS 104 - 11
RNTS 124 - 11
RNTS 144 - 11
RNTS 164 - 11
RNTS 184 - 11
RNTS 204 - 11
RNTS 204 - 7
RNTS 244 - 7
RNTS 4"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
DUPLEX RECEPTACLEDUP
GFI RECEPTACLEGFI
3 WAY ADAPTERT3120
4 WAY ADAPTERT490
ROUND BASE COVERRBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLINGCPLN2
(SPECIFY COUPLING LOCATION)
COUPLING
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
POLE MODEL NUMBER - RNTS 4" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com10
Round Straight SteelRNTS 5"
Pole Top Mount Hand Hole Cover
Below 15' - Hand hole cover withtamper resistant bolt assembly
15' and up - Reinforced hand holewith tamper resistant bolt assembly
Two Piece Base Cover Assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Shaft - 5" diameter, fabricated from high grade structural steel tube. Shaft conforms
to ASTM-A-501-68 specifications. Meets or exceeds minimum yield strength of
46,000 P.S.I. Wall thickness 11GA. (.120 wall) or 7 GA. (.180 wall) as specified.
Reinforced hand hole is furnished with cover. Shaft is furnished with ground lug
located inside pole on wall opposite hand hole.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
10½" - 12½" Dia.Bolt Circle
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
Locking bar
Hand hole cover
Tamper resistantscrew
Reinforcing welded bracket
Height
5"
U.S. ARCHITECTURAL LTG.www.usaltg.com 11
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTS 165 - 11
RNTS 185 - 11
RNTS 185 - 7
RNTS 205 - 11
RNTS 205 - 7
RNTS 255 - 11
RNTS 255 - 7
16'
18'
18'
20'
20'
25'
25'
11
11
7
11
7
11
7
11½"
11½"
11½"
11½"
11½"
11½"
11½"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120 OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
RECEPTACLE
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
15.8
12.6
43.9
10.1
32.5
10.9
19.7
12.6
10.0
32.1
7.9
22.3
7.6
13.2
10.0
8.1
16.3
6.5
14.9
5.9
10.7
8.1
6.5
12.4
5.2
10.1
4.1
8.0
200
175
325
150
275
125
250
RNTS 165 - 11
RNTS 185 - 11
RNTS 185 - 7
RNTS 205 - 11
RNTS 205 - 7
RNTS 255 - 11
RNTS 255 - 7
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
COUPLING
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
RNTS 5"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RNTS 5" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com12
55/8"
Height
Round Straight SteelRNTS 55/8"
Pole Top Mount Hand Hole CoverBelow 15' - Hand hole cover withtamper resistant bolt assembly
15' and up - Reinforced hand holewith tamper resistant bolt assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Shaft - 55/8" diameter, fabricated from high grade structural steel tube. Shaft
conforms to ASTM-A-501-68 specifications. Meets or exceeds minimum yield
strength of 46,000 P.S.I. Wall thickness 11GA. (.120 wall) or 7 GA. (.180 wall) as
specified. Reinforced hand hole is furnished with cover. Shaft is furnished with
ground lug located inside pole on wall opposite hand hole.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
10½" - 12½" Dia.Bolt Circle
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
Locking bar
Hand hole cover
Tamper resistantscrew
Reinforcing welded bracket
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 13
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTS 18558 - 3
RNTS 20558 - 3
RNTS 25558 - 3
RNTS 28558 - 3
RNTS 30558 - 3
18'
20'
25'
28'
30'
3
3
3
3
3
11½"
11½"
13½"
13½"
13½"
1"X36"X4"
1"X36"X4"
1¼"X42"X6"
1¼"X42"X6"
1¼"X42"X6"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120 OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
RECEPTACLE
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
36.6
25.3
15.0
13.1
11.9
18.5
16.9
12.2
10.4
9.1
14.2
11.5
9.1
7.9
6.9
375
325
300
250
225
RNTS 18558 - 3
RNTS 20558 - 3
RNTS 25558 - 3
RNTS 28558 - 3
RNTS 30558 - 3
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
COUPLING
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
RNTS 55/8"
POLE MODEL NUMBER - RNTS 55/8" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com14
6"
Height
Round Straight SteelRNTS 6"
Pole Top Mount Hand Hole Cover
Below 15' - Hand hole cover withtamper resistant bolt assembly
15' and up - Reinforced hand holewith tamper resistant bolt assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Shaft - 6" diameter, fabricated from high grade structural steel tube. Shaft
conforms to ASTM-A-501-68 specifications. Meets or exceeds minimum yield
strength of 46,000 P.S.I. Wall thickness 11GA. (.120 wall) or 7 GA. (.180 wall) as
specified. Reinforced hand hole is furnished with cover. Shaft is furnished with
ground lug located inside pole on wall opposite hand hole.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
11½" - 14½" Dia.Bolt Circle
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
Locking bar
Hand hole cover
Tamper resistantscrew
Reinforcing welded bracket
U.S. ARCHITECTURAL LTG.www.usaltg.com 15
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTS 186 - 7
RNTS 206 - 7
RNTS 256 - 7
RNTS 286 - 7
RNTS 306 - 7
18'
20'
25'
28'
30'
7
7
7
7
7
11½"
11½"
11½"
13½"
13½"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1¼"X42"X6"
1¼"X42"X6"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120 OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
RECEPTACLE
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPHMAX. FIXTURE
WEIGHT
41.7
28.9
17.1
14.9
13.6
21.1
19.3
13.9
11.9
10.4
16.2
13.1
10.4
9.0
7.9
375
325
300
250
225
RNTS 186 - 7
RNTS 206 - 7
RNTS 256 - 7
RNTS 286 - 7
RNTS 306 - 7
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
COUPLING
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
RNTS 6"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RNTS 6" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
U.S. ARCHITECTURAL LTG. www.usaltg.com16
65/8"
Height
RNTS 65/8"Round Straight Steel
Pole Top Mount Hand Hole CoverBelow 15' - Hand hole cover withtamper resistant bolt assembly
15' and up - Reinforced hand holewith tamper resistant bolt assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Shaft - 65/8" diameter, fabricated from high grade structural steel tube. Shaft
conforms to ASTM-A-501-68 specifications. Meets or exceeds minimum yield
strength of 46,000 P.S.I. Wall thickness 3GA. (.234 wall) as specified. Reinforced hand
hole is furnished with cover. Shaft is furnished with ground lug located inside pole
on wall opposite hand hole.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
11½" - 14½" Dia.Bolt Circle
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
18"HandHole
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¾"Maximum 4¾"
Locking bar
Hand hole cover
Tamper resistantscrew
Locking bar
Hand hole cover
Tamper resistantscrew
Reinforcing welded bracket
U.S. ARCHITECTURAL LTG.www.usaltg.com 17
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTS 18658 - 3
RNTS 20658 - 3
RNTS 25658 - 3
RNTS 28658 - 3
RNTS 30658 - 3
18'
20'
25'
28'
30'
3
3
3
3
3
11½"
11½"
13½"
13½"
13½"
1"X36"X4"
1"X36"X4"
1¼"X42"X6"
1¼"X42"X6"
1¼"X42"X6"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120 OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
RECEPTACLE
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER
75.1
51.0
35.2
27.1
21.6
41.8
34.6
27.1
20.8
16.5
32.4
26.2
20.8
16.0
17.2
400
350
325
400
375
RNTS 18658 - 3
RNTS 20658 - 3
RNTS 25658 - 3
RNTS 28658 - 3
RNTS 30658 - 3
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
COUPLING
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
RNTS 65/8"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RNTS 65/8" MOUNTING FINISH OPTIONS
MODEL NUMBER 100 MPH 90 MPH 80 MPHMAX. FIXTURE
WEIGHT
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com18
Height
Round Tapered SteelRTS
Pole Top Mount Hand Hole CoverBelow 15' - Hand hole cover withtamper resistant bolt assembly
15' and up - Reinforced hand holewith tamper resistant bolt assembly
Two Piece Base Cover Assembly
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Fabricated from structural quality hot rolled steel. Meets or exceeds
minimum yield strength of 36,000 P.S.I. Base telescopes and is circumferentially
welded to pole shaft. Slotted bolt holes provide 1" flexibility on either side of bolt circle
centerline.
Base Cover - Fabricated from heavy gauge quality carbon steel. Two piece cover
conceals base.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability.
Shaft - One or two piece construction fabricated from coil stock. Weldable grade.
Hot rolled commercial quality carbon steel. Guaranteed minimum yield strength
55,000 P.S.I. Shaft has uniform taper of approximately .14" per foot. Wall thickness
11 GA. (.120 wall) or 7 GA. (.180 wall) as specified. Flush reinforced hand hole is
furnished with cover. Shaft is furnished with ground lug located inside pole on wall
opposite hand hole.
Specifications
Tenon
Pole Top Plate
Pole Shaft
BoltProjection
Bolt Circle(See Ordering Specs.
under Poles)
18"HandHole
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:
(Consult Factory)
Locking bar
Hand hole cover
Tamper resistantscrew
Locking bar
Hand hole cover
Tamper resistantscrew
Reinforcing v bracket
U.S. ARCHITECTURAL LTG.www.usaltg.com 19
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RTS 20 - 11
RTS 25 - 11
RTS 30 - 11
RTS 35 - 11
RTS 40 - 11
RTS 40 - 7
RTS 45 - 11
RTS 45 - 7
RTS 50 - 11
RTS 50 - 7
20'
25'
30'
35'
40'
40'
45'
45'
50'
50'
11
11
11
11
11
7
11
7
11
7
6.0X3.0
7.0X3.5
8.0X4.0
8.5X3.5
9.0X3.6
9.0X3.6
10.0X3.7
10.0X3.7
10.0X3.0
10.0X3.0
11½"
11½"
11½"
11½"
11½"
13½"
13½"
13½"
13½"
13½"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1¼"X42"X6"
1¼"X42"X6"
1¼"X42"X6"
1¼"X42"X6"
1¼"X42"X6"
POLEHEIGHT
SHAFTSIZE
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDSMOOTH FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
23.2
24.4
22.4
22.2
20.9
30.6
21.1
28.1
15.1
16.2
17.5
18.7
17.1
17.0
15.5
24.7
15.9
21.3
11.3
12.7
13.1
14.3
12.5
12.3
10.8
18.9
10.6
16.5
8.5
10.1
10.7
11.8
10.2
10.1
8.6
15.6
8.2
13.2
6.3
8.3
375
325
425
375
350
550
350
550
275
325
RTS 20 - 11
RTS 25 - 11
RTS 30 - 11
RTS 35 - 11
RTS 40 - 11
RTS 40 - 7
RTS 45 - 11
RTS 45 - 7
RTS 50 - 11
RTS 50 - 7
SPECIFY OTHER HEIGHTS
RTS
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019
GREENRAL-6005
WHITERAL-9003
GREYRAL-7004
BLACKRAL-9005
ALL STEEL POLES SUPPLIEDWITH SMOOTH FINISH
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RTS MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com20
Height
4"
Square Straight AluminumSNTA 4"
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Shaft - 4" square, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
10¼" Dia.Bolt Circle
Two Piece Base Cover Assembly
Specifications
BoltProjection
18"HandHole
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 21
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTA 84 - 125
SNTA 104 - 125
SNTA 124 - 125
SNTA 144 - 125
SNTA 164 - 125
SNTA 164 - 188
SNTA 184 - 125
SNTA 184 - 188
SNTA 204 - 188
8'
10'
12'
14'
16'
16'
18'
18'
20'
.125
.125
.125
.125
.125
.188
.125
.188
.188
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustained wind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
27.4
20.0
14.9
11.2
8.2
13.7
6.2
11.0
8.3
20.5
14.6
10.5
7.5
5.2
9.4
3.5
7.1
5.1
15.7
11.1
7.5
5.0
3.2
6.6
1.7
4.7
2.9
12.2
8.2
5.4
3.3
1.8
4.4
N/A
2.9
1.4
100
100
100
100
100
200
100
125
125
SNTA 84 - 125
SNTA 104 - 125
SNTA 124 - 125
SNTA 144 - 125
SNTA 164 - 125
SNTA 164 - 188
SNTA 184 - 125
SNTA 184 - 188
SNTA 204 - 188
SNTA 4"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTA 4" MOUNTING FINISH OPTIONS
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com22
Height
5"
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to produce a T6 temper. Structurally engineered base includes eight heavy wall reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft at both the outside top and inside bottom of the base.
Square Straight AluminumSNTA 5"
Shaft - 5" square, extruded from 6063 alloy aluminum tubing. Heat treated to produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is furnished with ground lugs located on cast aluminum base plate.
Two Piece Base Cover Assembly
11¾" Dia.Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount
Tenon
Pole Top Plate
Pole Shaft
Hand Hole CoverPT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Hand hole cover withtamper resistant bolt assembly
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 23
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTA 125 - 125
SNTA 145 - 125
SNTA 165 - 125
SNTA 185 - 188
SNTA 205 - 188
SNTA 255 - 188
12'
14'
16'
18'
20'
25'
.125
.125
.125
.188
.188
.188
11¾"
11¾"
11¾"
11¾"
11¾"
11¾"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
12.8
10.0
7.6
19.5
15.5
8.7
10.4
8.3
6.2
13.4
10.3
4.9
8.1
6.3
5.0
9.6
6.9
1.9
6.6
5.1
3.5
6.5
4.2
N/A
150
100
100
200
200
100
SNTA 125 - 125
SNTA 145 - 125
SNTA 165 - 125
SNTA 185 - 188
SNTA 205 - 188
SNTA 255 - 188
SNTA 5"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTA 5" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com24
Height
6"
Square Straight AluminumSNTA 6"
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Shaft - 6" square, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
Two Piece Base Cover Assembly
13" Dia. Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount Hand Hole Cover
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Hand hole cover withtamper resistant bolt assembly
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 25
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTA 206 - 250
SNTA 206 - 188
SNTA 256 - 250
SNTA 256 - 188
SNTA 306 - 250
SNTA 306 - 188
20'
20'
25'
25'
30'
30'
.250
.188
.250
.188
.250
.188
13"
13"
13"
13"
13"
13"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
34.6
22.2
21.4
14.1
13.7
8.1
24.5
14.4
13.7
8.3
7.1
3.6
17.6
10.8
9.4
5.0
4.0
N/A
12.7
6.8
5.7
2.0
N/A
N/A
250
250
250
200
250
150
SNTA 206 - 250
SNTA 206 - 188
SNTA 256 - 250
SNTA 256 - 188
SNTA 306 - 250
SNTA 306 - 188
SNTA 6"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTA 6" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com26
Height
4"
Square Round Corner Straight AluminumSNTAR 4"
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Shaft - 4" square (round corner), extruded from 6063 alloy aluminum tubing. Heat
treated to produce a T6 temper. Shaft includes a hand hole furnished with cover.
Shaft is furnished with ground lugs located on cast aluminum base plate.
10¼" Dia.Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount
Tenon
Pole Top Plate
Pole Shaft
Hand Hole Cover
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Hand hole cover withtamper resistant bolt assembly
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 27
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTAR 84 - 125
SNTAR 104 - 125
SNTAR 124 - 125
SNTAR 154 - 125
SNTAR 154 - 188
SNTAR 184 - 125
SNTAR 184 - 188
SNTAR 204 - 188
8'
10'
12'
15'
15'
18'
18'
20'
.125
.125
.125
.125
.188
.125
.188
.188
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
10¼"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
33.8
25.2
19.7
11.1
17.8
7.7
12.3
10.1
26.0
19.2
14.6
7.6
13.0
4.4
8.4
6.2
20.0
14.6
10.8
5.2
9.5
2.5
5.7
3.8
15.7
11.2
8.0
3.5
7.0
1.1
3.7
2.0
100
100
100
100
100
100
400
450
SNTAR 84 - 125
SNTAR 104 - 125
SNTAR 124 - 125
SNTAR 154 - 125
SNTAR 154 - 188
SNTAR 184 - 125
SNTAR 184 - 188
SNTAR 204 - 188
SNTAR 4"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTAR 4" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com28
Height
5"
Square Round Corner Straight AluminumSNTAR 5"
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Shaft - 5" square (round corner), extruded from 6063 alloy aluminum tubing. Heat
treated to produce a T6 temper. Shaft includes a hand hole furnished with cover.
Shaft is furnished with ground lugs located on cast aluminum base plate.
11¾" Dia.Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount
Tenon
Pole Top Plate
Pole Shaft
Hand Hole Cover
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Hand hole cover withtamper resistant bolt assembly
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 29
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTAR 155 - 125
SNTAR 185 - 125
SNTAR 185 - 188
SNTAR 205 - 125
SNTAR 205 - 188
SNTAR 255 - 188
15'
18'
18'
20'
20'
25'
.125
.125
.188
.125
.188
.188
11¾"
11¾"
11¾"
11¾"
11¾"
11¾"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
19.2
14.1
22.7
11.5
18.8
12.4
13.8
9.2
16.1
6.7
12.8
6.3
9.9
6.0
11.5
3.9
8.7
3.2
7.2
3.8
8.2
1.9
5.8
1.0
100
100
150
100
150
150
SNTAR 155 - 125
SNTAR 185 - 125
SNTAR 185 - 188
SNTAR 205 - 125
SNTAR 205 - 188
SNTAR 255 - 188
SNTAR 5"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - SNTAR 5" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com30
Height
6"
Square Round Corner Straight AluminumSNTAR 6"
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Shaft - 6" square (round corner), extruded from 6063 alloy aluminum tubing. Heat
treated to produce a T6 temper. Shaft includes a hand hole furnished with cover.
Shaft is furnished with ground lugs located on cast aluminum base plate.
13" Dia.Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount Hand Hole Cover
Tenon
Pole Top Plate
Pole Shaft
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Hand hole cover withtamper resistant bolt assembly
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 31
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
SNTAR 256 - 188
SNTAR 306 - 188
SNTAR 306 - 250
SNTAR 356 - 250
25'
30'
30'
35'
.188
.188
.250
.250
13"
13"
13"
13"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLEDUP
GFI RECEPTACLEGFI
3 WAY ADAPTERT3120
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLINGCPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
20.2
16.2
18.9
20.6
12.4
5.1
10.5
4.3
7.6
1.6
5.9
N/A
4.2
N/A
2.6
N/A
150
150
150
150
SNTAR 256 - 188
SNTAR 306 - 188
SNTAR 306 - 250
SNTAR 356 - 250
SNTAR 6"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
180˚
90˚
270˚
0˚
270º
0º
90º
180º
POLE MODEL NUMBER - SNTAR 6" MOUNTING FINISH OPTIONS
U.S. ARCHITECTURAL LTG. www.usaltg.com32
Height
4"
Shaft - 4" diameter, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Round Straight AluminumRNTA 4"
Two Piece Base Cover Assembly
10¼" Dia.Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 33
Drilled Side MountSpecify drilling location using codes below.
0º
180º
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTA 84 - 125
RNTA 104 - 125
RNTA 124 - 125
RNTA 144 - 125
8'
10'
12'
14'
.125
.125
.125
.125
10¼"
10¼"
10¼"
10¼"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
¾"X18"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
15.2
10.9
8.5
6.6
11.4
8.0
6.0
4.5
8.7
6.0
4.4
3.1
6.9
4.7
3.3
2.2
100
100
100
100
RNTA 84 - 125
RNTA 104 - 125
RNTA 124 - 125
RNTA 144 - 125
RNTA 4"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Specifications and Ordering
POLE MODEL NUMBER - RNTA 4" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com34
Height
5"
Shaft - 5" diameter, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Round Straight AluminumRNTA 5"
Two Piece Base Cover Assembly
11¾" Dia.Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 35
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTA 105 - 125
RNTA 125 - 125
RNTA 145 - 125
RNTA 145 - 188
RNTA 165 - 125
RNTA 165 - 188
RNTA 185 - 125
RNTA 185 - 188
RNTA 205 - 188
10'
12'
14'
14'
16'
16'
18'
18'
20'
.125
.125
.125
.188
.125
.188
.125
.188
.188
11¾"
11¾"
11¾"
11¾"
11¾"
11¾"
11¾"
11¾"
11¾"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
¾"X24"X3"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT _____
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
18.8
14.6
9.9
18.1
7.3
11.7
5.6
9.5
7.6
13.9
10.6
7.1
13.4
5.2
8.5
3.8
6.7
5.2
10.8
8.3
5.5
10.3
4.0
6.6
2.9
5.2
4.0
8.7
6.8
4.4
8.3
3.2
5.4
2.2
4.1
3.1
175
175
175
250
100
200
100
200
200
RNTA 105 - 125
RNTA 125 - 125
RNTA 145 - 125
RNTA 145 - 188
RNTA 165 - 125
RNTA 165 - 188
RNTA 185 - 125
RNTA 185 - 188
RNTA 205 - 188
SPECIFY OTHER HEIGHTS
RNTA 5"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RNTA 5" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com36
55/8"
Height
Shaft - 55/8" diameter, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Round Straight Aluminum
Two Piece Base Cover Assembly
11¾" Dia.Bolt Circle
Specifications
BoltProjection
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
18"HandHole
Locking bar
Hand hole cover
Tamper resistantscrew
RNTA 55/8"
U.S. ARCHITECTURAL LTG.www.usaltg.com 37
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTA 20558 - 375
RNTA 25558 - 375
RNTA 30558 - 375
20'
25'
30'
.375
.375
.375
11¾"
11¾"
11¾"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
12.4
7.5
4.4
8.6
5.2
3.1
6.8
4.1
2.4
5.1
3.1
1.8
275
275
275
RNTA 20558 - 375
RNTA 25558 - 375
RNTA 30558 - 375
SPECIFY OTHER HEIGHTS
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
RNTA 55/8"
POLE MODEL NUMBER - RNTA 55/8" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com38
6"
Height
Shaft - 6" diameter, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Round Straight AluminumRNTA 6"
Two Piece Base Cover Assembly
13" Dia. Bolt Circle
Specifications
BoltProjection
18"HandHole
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 39
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTA 206 - 188
RNTA 256 - 188
RNTA 306 - 188
20'
25'
30'
.250
.250
.250
13"
13"
13"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
13.5
7.9
4.5`
10.5
5.7
3.0
7.9
4.3
2.0
6.1
3.3
1.4
100lbs
100lbs
100lbs
RNTA 206 - 188
RNTA 256 - 188
RNTA 306 - 188
SPECIFY OTHER HEIGHTS
RNTA 6"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RNTA 6" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com40
Shaft - 65/8" diameter, extruded from 6063 alloy aluminum tubing. Heat treated to
produce a T6 temper. Shaft includes a hand hole furnished with cover. Shaft is
furnished with ground lugs located on cast aluminum base plate.
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Round Straight Aluminum
13" Dia.Bolt Circle
Specifications
BoltProjection
Bolt ProjectionAbove Grade:Minimum 3¼"Maximum 3¾"
18"HandHole
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Two Piece Base Cover Assembly
Locking bar
Hand hole cover
Tamper resistantscrew
RNTA 65/8"
65/8"
Height
U.S. ARCHITECTURAL LTG.www.usaltg.com 41
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RNTA 2066 - 250
RNTA 2566 - 250
RNTA 3066 - 250
20'
25'
30'
.250
.250
.250
13"
13"
13"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
14.1
8.4
4.0
11.4
6.6
3.1
9.0
5.1
2.4
6.9
4.0
1.9
300
300
300
RNTA 2066 - 250
RNTA 2566 - 250
RNTA 3066 - 250
SPECIFY OTHER HEIGHTS
RNTA 65/8"
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RNTA 65/8" MOUNTING FINISH OPTIONS
180˚
90˚
270˚
0˚
270º
90º
U.S. ARCHITECTURAL LTG. www.usaltg.com42
Height
Round Tapered AluminumRTA
Finish - Electrostatically applied TGIC Polyester Powder Coat on substrate
prepared with 20 PSI power wash at 140°F. Four step iron phosphate
pretreatment for protection and paint adhesion. 400°F bake for maximum
hardness and durability. Textured finish is standard.
Base Cover - Fabricated from heavy wall aluminum construction. Two piece cover
conceals base.
Anchorage - (4) anchor bolts fabricated from hot rolled steel bar. Minimum yield
strength of 50,000 P.S.I. Bolts have "L" bend on one end and are threaded on the
other. Bolts are fully galvanized and are furnished with two nuts and two washers.
Base Plate - Cast aluminum constructed of A-356 aluminum alloy heat treated to
produce a T6 temper. Structurally engineered base includes eight heavy wall
reinforcing vertical gussets. Base telescopes and is circumferentially welded to shaft
at both the outside top and inside bottom of the base.
Shaft - Spun tapered from 6063 alloy aluminum tubing. Heat treated to produce a
T6 temper. Shaft includes a peripherally reinforced hand hole furnished with cover.
Shaft is furnished with ground lugs located on cast aluminum base plate.
Specifications
BoltProjection
Bolt Circle(See Ordering Specs.
under Poles)
18"HandHole
Pole Top Mount Hand Hole Cover
Hand hole cover withtamper resistant bolt assembly
Tenon
Pole Top Plate
Pole Shaft
Two Piece Base Cover Assembly
PT23 - 23/8"X4" Tenon
PT27 - 27/8"X4" Tenon
Bolt ProjectionAbove Grade:
(Consult Factory)
Locking bar
Hand hole cover
Tamper resistantscrew
U.S. ARCHITECTURAL LTG.www.usaltg.com 43
4-90 . . . . . . . . . .
3-120 . . . . . . . . .
1 . . . . . . . . . . . . . . .
RTA 1443 - 125
RTA 1643 - 125
RTA 1853 - 188
RTA 2064 - 188
RTA 2574 - 188
RTA 3084 - 188
RTA 3584 - 188
RTA 4084 - 250
DUPLEX RECEPTACLE DUP
GFI RECEPTACLE GFI
3 WAY ADAPTER T3120
4 WAY ADAPTER T490
ROUND BASE COVER RBC
½'' COUPLING CPLN1/2
¾'' COUPLINGCPLN3/4
2'' COUPLING CPLN2
(SPECIFY COUPLING LOCATION)
OTHER TENON MT
PT2323/8" X 4" TENON
PT2727/8" X 4" TENON
DRILL MOUNT
2-90 . . . . . . . . . . .
2-180 . . . . . . . .
3-90 . . . . . . . . .
ARM MOUNT STANDARDTEXTURED FINISH
COUPLING
RECEPTACLE
3-120 REQUIRES PT27AND T3120 ADAPTER
2-90, 3-90, 4-90 REQUIRESPT27 AND T490 ADAPTER
REFER TO THE ACCESSORIES SECTION FOR OTHER OPTIONS
All above design calculations are based on sustainedwind forces plus additional 1.3 wind gust
(Example: Pole rated at 80 MPH withstands 104 MPH gusts)
MODEL NUMBER 100 MPH 90 MPH 80 MPH 70 MPHMAX. FIXTURE
WEIGHT
6.2
4.4
10.8
14.2
13.6
13.5
9.3
10.7
4.5
2.9
7.6
10.1
9.5
9.9
7.0
7.6
3.0
1.8
5.6
7.5
7.3
7.4
5.1
5.4
2.2
1.1
4.1
5.6
5.7
5.6
3.8
4.2
50
50
100
200
225
200
100
200
RTA 1443 - 125
RTA 1643 - 125
RTA 1853 - 188
RTA 2064 - 188
RTA 2574 - 188
RTA 3084 - 188
RTA 3584 - 188
RTA 4084 - 250
RTA
Engineering DataMaximum EPA - Square Feet
DARK BRONZERAL-8019-T
GREENRAL-6005-T
WHITERAL-9003-T
GREYRAL-7004-T
BLACKRAL-9005-T
FOR SMOOTH FINISHREMOVE SUFFIX “T”
(EXAMPLE: RAL-9005)
CONSULT FACTORY FOR CUSTOM COLORS
Drilled Side MountSpecify drilling location using codes below.
Specifications and Ordering
0º
180º
POLE MODEL NUMBER - RTA MOUNTING FINISH OPTIONS
.125
.125
.188
.188
.188
.188
.188
.188
14'
16'
18'
20'
25'
30'
35'
40'
4.0X3.0
4.0X3.0
5.0X3.0
6.0X4.0
7.0X4.0
8.0X4.0
8.0X4.0
8.0X4.0
10¼"
11¾"
11¾"
13"
13"
13"
13"
13"
¾"X18"X3"
¾"X18"X3"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
1"X36"X4"
POLEHEIGHT
SHAFTSIZE
WALLTHICKNESS
BOLTCIRCLE
ANCHORAGE
SPECIFY OTHER HEIGHTS
180˚
90˚
270˚
0˚
270º90º
U.S. ARCHITECTURAL LTG. www.usaltg.com44
ABH - WMSBH - WM
ABH - 1SBH - 1
ABH - 2 - 180SBH - 2 - 180
ABH - 3 - 180SBH - 3 - 180
ABH - 3 - 120SBH - 3 - 120
ABH - 4 - 120SBH - 4 - 120
ABH - 4 - 90SBH - 4 - 90
ABH - 4 - 180SBH - 4 - 180
(Aluminum = ABH-3-180)(Steel = SBH-3-180)
E.P.A. = 0.69
18" 18"
15"
(Aluminum = ABH-2-180)(Steel = SBH-2-180)
E.P.A. = 0.37
15"
36"
(Aluminum = ABH-4-180)(Steel = SBH-4-180)
E.P.A. = 0.83
30"
15"
36" 30"
23/8" O.D.
23/8" O.D. 23/8" O.D.
27/16" I.D. fitter*
27/16" I.D. fitter* 27/16" I.D. fitter*
*Fitter accepts23/8" O.D. X 4" tenon
ABH/SBH
Aluminum: Extruded from 6063 alloy aluminum heat treated to produce a T6 temper.
Steel: Fabricated from high grade structural quality hot rolled carbon steel.
Steel = SBHAluminum = ABH
U.S. ARCHITECTURAL LTG.www.usaltg.com 45
ASA - WMSSA - WM
ASA - 1SSA - 1
ASA - 2 - 180SSA - 2 - 180
ASA - 3 - 180SSA - 3 - 180
ASA - 3 - 90SSA - 3 - 90
ASAH - 4SSAH - 4
ASA - 4 - 90SSA - 4 - 90
ASA - 5 - 90SSA - 5 - 90
Steel = SSAAluminum = ASA
42" Removable
top cap
4"X4" Arm (Aluminum = ASA-4-90)
(Steel = SSA-4-90)E.P.A. = 1.72
42"
(Aluminum = ASAH-4)(Steel = SSAH-4)
E.P.A. = 1.72
21"
30"
(Aluminum= ASA-WM)(Steel= SSA-WM)
10"
4"5½"
6"
7½"
(4)½" HOLES
(Aluminum = ASA-2-180)(Steel = SSA-2-180)
E.P.A. = 1.27
30"
(Aluminum = ASA-3-180)(Steel = SSA-3-180)
E.P.A. = 2.31
30"
30"
Removableend cap
23/8" O.D. X 4"Tenon
ASA/SSA
Aluminum: Extruded from 6063 alloy aluminum heat treated to produce a T6 temper.
Steel: Fabricated from high grade structural quality hot rolled carbon steel.
U.S. ARCHITECTURAL LTG. www.usaltg.com46
1 2 - 180 3 - 90 3 - 120 4 - 90
SL1-4'-0"E.P.A. = 0.66
SL1-6'-0"E.P.A. = 0.96
SL1-8'-0"E.P.A. = 1.25
4'-0" Min. 8'-0" Max.
(Specify after cat. no.)To order a 6'-0" arm, specify: SL1-6'-0"
23/8" O.D. pipe
Removabletop cap
SL
Cast iron clamp on bracket with 2" steel pipe (23/8" O.D.) arm.
Arm constructed from high grade structural steel.
U.S. ARCHITECTURAL LTG.www.usaltg.com 47
ASP - WM SSP - WM
ASP - 1 SSP - 1
ASP - 2 - 180 SSP - 2 - 180
ASP - 3 - 180 SSP - 3 - 180
ASP - 3 - 90 SSP - 3 - 90
ASPH - 4 SSPH - 4
ASP - 4 - 90 SSP - 4 - 90
ASP - 5 - 90 SSP - 5 - 90
Steel = SSPAluminum = ASP
10"
6"
7½"
(4)½" Holes
24"
12"
4"X4" Arm
Removabletop cap
Plate providedas required
(Aluminum = ASP-1)(Steel = SSP-1)
E.P.A. = 0.40
(Aluminum = ASP-4-90)(Steel = SSP-4-90)
E.P.A. = 1.20
(Aluminum = ASP-WM)(Steel = SSP-WM)
(Aluminum = ASP-2-180)(Steel = SSP-2-180)
E.P.A. = 0.80
24"
ASP/SSP
Aluminum: Extruded from 6063 alloy aluminum heat treated to produce a T6 temper.
Steel: Fabricated from high grade structural quality hot rolled carbon steel.
4"5½"
U.S. ARCHITECTURAL LTG. www.usaltg.com48
ATR - WM - 1STR - WM - 1
ATR - 2STR - 2
ATR - 3STR - 3
ATR - 4STR - 4
ATR - WM - 1 - 1STR - WM - 1 - 1
ATR - 2 - 2STR - 2 - 2
ATR - 3 - 2STR - 3 - 2
ATR - 4 - 4STR - 4 - 4
4"X4" Arm
Removableend cap
½" Pipe coupling(3/4" Available - specify)
24"
24"
24"
(Aluminum = ATR-4)(Steel = STR-4)
E.P.A. = 2.83
4"X4" Arm
½" Pipe coupling(3/4" Available - specify)
Removableend cap
(Aluminum = ATR-4-4)(Steel = STR-4-4)
E.P.A. = 3.03
24"
24"
24"
24"
24"
(Aluminum = ATR-3-2)(Steel = STR-3-2)
E.P.A. = 2.08
24"
(Aluminum = ATR-2)(Steel = STR-2)
E.P.A. = 1.03
Upper coupling only:
Upper and lower coupling:
27/16" I.D. fitter*
27/16" I.D. fitter*
27/16" I.D. fitter* 27/16" I.D. fitter*
ATR/STR
Aluminum: Extruded from 6063 alloy aluminum heat treated to produce a T6 temper.
Steel: Fabricated from high grade structural quality hot rolled carbon steel.
*Fitter accepts23/8" O.D. X 4" tenon
Steel = STRAluminum = ATR
U.S. ARCHITECTURAL LTG.www.usaltg.com 49
ACCESSORIES
DUPDuplex Receptacle with Cover
RBAField Rotatable Banner Arm
RBHField Rotatable Basket Holder
RFHField Rotatable Flag Holder
BEBBanner Eye Bolt
RBCRound Base Cover
GFIDuplex Receptacle
with Cover
FBAFixed Banner Arm
FBHFixed Basket Holder
FFHFixed Flag Holder
BBABreak Away Banner
Arm
HNBHinge Base
Standard Length 18"
Standard Length 12"
Standard Length 18"
Standard Length 12"
Standard Length 24"
Available for 4" and 5" Round and
Square Poles 20'-0" Max. Height
13/8" I.D.
12"
13/8" I.D.
12"
U.S. ARCHITECTURAL LTG. www.usaltg.com50
Spoke Arms Assemblies mount over 2.375" O.D. Tenon - 2.375" O.D. X 4" Arms provided
Set Screws provided to secure Spoke Arm Assembly to Pole Tenon
SMStem Mount and Swivel Canopy
NKLE23NKLE27Adjustable Knuckle Fitter
T490Top 4 Way Fitter Adaptor
PT27PT23Pole Tenon
RST4RST5RST6Removable tenon for Square Poles
CMChain Mount
ST23Street Arm Adaptor
T3120Top 3 Way Fitter
Adaptor
RPA4RPA5RPA6
Round Pole Adaptor
RRT4RRT5RRT6
Removable Tenon for Round Poles
SPOKE ARMS
SAT1 SAT2-180 SAT12-90 SAT3-90 SAT3-120 SAT4-90
4'-0" Max.
4" 4"
4'-0" Max.3/8" I.P.S.1" threaded Ends75lbs. Max.45° Swivel Action
NKLE23 fits over 2.375 O.D.NKLE27 fits over 2.875 O.D.
Set Screws provided to secure Fitter to
Pole Tenon.
Set Screws provided to secure Fitter to Pole Tenon.
Fits over 2.375 O.D. X 4" Tenon. (Drilled as required) Set Screws provided to secure Fitter to Pole Tenon. Thru Bolt provided to prevent windmilling.
Fits over 2.375 O.D. X 4" Tenon.
(Drilled as required) Set Screws provided
to secure Fitter to Pole Tenon. Thru Bolt provided to
prevent windmilling.
PT23 fits over 2.375 X 4" TenonPT23 fits over 2.875 X 4" Tenon
Fits over 2.375 O.D. Arm
RPA4 fits 4" Dia. PoleRPA5 fits 5" Dia. PoleRPA6 fits 6" Dia. Pole
Set Screws provided to secure Fitter to
Pole Tenon.
RST4 fits 4" Sq. PoleRST5 fits 5" Sq. PoleRST6 fits 6" Sq. Pole
Set Screws provided to secure Fitter to Pole Tenon.
RST4 fits 4" Sq. PoleRST5 fits 5" Sq. PoleRST6 fits 6" Sq. Pole
U.S. ARCHITECTURAL LTG.www.usaltg.com 51
TERMS AND CONDITION OF SALE
TERMSNet 30 days from date of shipment (subject to credit approval). A service charge of 1½% per month will be made on past due accounts.
PRICINGPublished prices are subject to change without notice. Possession of price sheets in no way obligates company to sell at those prices. All orders will be acknowledged by and are subject to acceptance by the company. Order will be billed at pricing indicated. Hold orders will be invoiced at the prevailing price at time of order release. Minimum billing will be $50.00 net. All invoices are subject to federal, state and local taxes and will be added to the invoice where applicable.
FREIGHTAll shipments are FOB factory and will be shipped via land transportation at company discretion. Title passes to consignee on delivery to the carrier. All claims for loss or damage in transit must be made to the delivery carrier by consignee. Material will be prepaid and billed to our customer unless otherwise stated in writing by company.
ACKNOWLEDGE SHIPPING SCHEDULEShip date indicated on order acknowledgment is the best approximation of the probable shipment date and shall not be deemed to represent a fixed or guaranteed shipment date. Factory shall not be responsible for any penalties or labor charges resulting from delayed shipments due to acts or causes beyond our control or its ability to ship by the acknowledged date.
CANCELATION CHARGECompany reserves the right to assess a minimum cancellation charge of 50% of the order value if the order is cancelled after it has been processed for shipment.
RETURNED GOODSNo material can be returned without permission, in writing, from factory. On material accepted for return, purchaser must pay return shipment charges and pay minimum 25% restocking charge plus additional charges required to rework goods to a resalable condition. Request to return material must be made to the company within forty-five (45) days from date of shipment.
GENERALFactory reserves the right to charge specification features without notice.
WARRANTYAll factory products are carefully tested and inspected before shipment and warranted to be free of defects in material or workmanship for a period of one year from date of shipment from our factory. Any such defective products will be repaired or replaced, at the option of the company, provided a written claim is made within this warranty period.
Finishes are warranted not to peel, crack, blister or craze from normal atmospheric exposure for one (1) year from date of shipment.
Company will accept no charges for any labor, repair costs or transportation charges incurred without prior written authorization from factory.
The responsibility of company for any defective material is limited solely to the replacement or repair of the material and does not include any incidental or consequential damages which may be incurred.
Company products have been designed in accordance with accepted engineering practices to be structurally capable of loads developed by the velocity pressure of winds as specified. In selecting poles, the total effective projected area allowed for the pole has been exceeded.
No warranty, express or implied, exists other than that included above. No person, agent or distributor is warranted to give any other warranty on behalf of the company.
U.S. ARCHITECTURAL LTG. www.usaltg.com52
NOTES
U.S. ARCHITECTURAL LTG.www.usaltg.com 53
80
90
90
90
Hawaii
Alaska
110
110
110
110
110
110
110
110
70
70
80
70
80
80
90
90
70
70
80
80
80
8070
70
70
70
Yuma
Phoenix
90
90
100
100
100
100
Juneau
Anchorage
Fairbanks
San Diego
Miami
Tampa
FresnoTonopah
Milford
Salt Lake CityReno
70
70
8090
80
Eureka
Roseburg
Denver
Portland
SeattleSpokane
Pendleton
Burns Boise
Missoula Great FallsHavre
Pocatello
Billings
International Falls
S Ste. Marie
Williston
Lander
Cheyenne North Platte
Huron
Des Moines
Dubuque
Lincoln
Dodge City
Amarillo
Fort Worth
Las Vegas
El Paso
San FranciscoGrand Junction
Los Angeles
Houston
MinneapolisGreen Bay
Columbus
Bismarck Duluth
Kansas City
Memphis
NashvilleKnoxville
Lexington
Fargo
Charleston
HarrisburgPittsburgh
Washington
Burlington
Boston
New York
Richmond
80
90
100
110
Hawaii 80 MPHPuerto Rico 95 MPH
Jacksonville
Charleston
Wilmington
Raleigh
Norfolk
Hatteras
AtlantaColumbia
Birmingham
Jackson
Brownsville
San Antonio
New Orleans
Little Rock
St. Louis
Springfield
Indianapolis
Lansing
Detroit
BuffaloAlbany
Chicago
Shreveport
Pensacola
Caribou
Portland
Concord
New Haven
Albuquerque Oklahoma City
Del Rio
Abilene
The 50 year mean recurrence Isotach wind map has been included in this catalog in order to aid in the selection of a pole with
regard to its geographic location. Although a less stringent 25 year mean recurrence map is sometimes used by other pole
suppliers, it is our belief that the added measure of assurance offered in the use of this map deems it more desirable. Where
unusual wind conditions exist [mountains, natural terrain acting as funnels, hurricane regions (shown as 110 MPH regions)] it is
advisable to contact U.S. ARCHITECTURAL LIGHTING for further consultation.
Isotach Wind Map
Maximum Expected Wind Velocitiesin the United States
U.S. POLE COMPANY660 West Avenue OPalmdale, California 93551Toll Free (800) 877-6537www.usaltg.com