Final Catalog6Pipe Hangers
Pipe hangers presented in this section are designed to support insulated or non- insulated pipe allowing for vertical adjustment and limited movement in the piping system. Materials: Carbon Steel, Malleable Iron, 304 and 316 Stainless Steel are used in the manufacturing of riser and pipe clamps. Other materials are also available. Finishes: Finishes for pipe supports in this section are Plain Steel, Electro-Plated Zinc, Hot Dipped Galvanized, Red Primer, Plastic Coating, Copper Plated, Stainless Steel and other special coatings are also available. Notes: Products in this section are designed and manufactured in accordance with industry standards. RHK is not responsible for injuries and damage which could re- sult from improper and negligent installation of the items.
131
Adjustment "F"
Wt./C (Lbs.)
K3100 - 1/2 1/2" 3/8" - 16 2 1/8" 1 11/16" 15/16" 2 1/2" 7/16" 730 25
K3100 - 3/4 3/4" 3/8" - 16 2 7/16" 1 7/8" 1 1/8" 2 1/2" 1/2" 730 29
K3100 - 1 1" 3/8" - 16 2 13/16" 2 1/8" 1 3/8" 2 1/2" 5/8" 730 35
K3100 - 1 1/4 1 1/4" 3/8" - 16 3 7/16" 2 9/16" 1 13/16" 2 1/2" 7/8" 730 40
K3100 - 1 1/2 1 1/2" 3/8" - 16 4" 3" 2 1/4" 2 1/2" 1 3/16" 730 42
K3100 - 2 2" 3/8" - 16 4 1/2" 3 1/4" 2 1/2" 2 1/2" 1 5/8" 730 52
K3100 - 2 1/2 2 1/2" 1/2" - 13 5 9/16" 4" 3 1/16" 2 1/2" 2" 1350 90
K3100 - 3 3" 1/2" - 13 6 3/4" 4 7/8" 3 15/16" 2 1/2" 2" 1350 110
K3100 - 3 1/2 3 1/2" 1/2" - 13 7" 5" 4 1/16" 2 1/2" 2" 1350 142
K3100 - 4 4" 5/8" - 11 7 13/16" 5 1/2" 4 3/8" 2 1/2" 2" 1430 132
K3100 - 5 5" 5/8" - 11 9 1/16" 6 1/8" 5" 2 1/2" 2" 1430 215
K3100 - 6 6" 3/4" - 10 10 7/16" 6 15/16" 5 11/16" 3" 2" 1940 320
K3100 - 8 8" 3/4" - 10 12 3/4" 8 3/8" 7 1/8" 3 1/2" 2 5/16" 2000 485
K3100 - 10 10" 7/8" - 9 15 1/4" 9 13/16" 8 3/8" 3 1/2" 2 5/16" 3600 846
K3100 - 12 12" 7/8" - 9 17 5/8" 11 3/16" 9 11/16" 3 1/2" 2 5/8" 3800 1083
K3100 - 14 14" 1" - 8 19 9/16" 12 1/2" 10 5/8" 4" 2 7/8" 4200 1432
K3100 - 16 16" 1" - 8 21 7/16" 13 5/16" 11 9/16" 4" 2 11/16" 4600 2200
K3100 - 18 18" 1" - 8 25" 15 7/8" 14 3/16" 4 1/2" 3 15/16" 4800 2500
K3100 - 20 20" 1 1/4" - 7 27 1/2" 17 3/8" 16 5/8" 5" 5 3/8" 4800 4400
K3100 - 24 24" 1 1/4" - 7 31 3/4" 19 5/8" 18 5/8" 5" 5 3/8" 4800 5000
K3100 - 30 30" 1 1/4" - 7 38 7/8" 23 3/4" 22 3/4" 5" 6 1/4" 6000 6600
K3100 - 36 36" 1 1/4" - 7 46" 27 13/16" 25" 5" 5 7/16" 6000 8474
Material: Steel Standard Finish: Plain, Electro- Plated, Hot-Dip Galvanized or Stainless Steel Service: Designed for suspending non-insulated stationary pipe al- lowing for vertical adjustment Ordering: Specify part number and finish
Notes: When using oversized clevis hangers, install K3100PS (Pipe Sleeve) over cross bolt to prevent deformation of clevis bottom. When attaching seismic bracing to clevis hang- ers, a K3100PS (Pipe Sleeve) must be installed over the cross bolt
K3100PVC - Plastic Coated
Adjustment "F"
Wt./C (Lbs.)
K3100CU - 1/2 1/2" 3/8" - 16 2 1/4" 1 15/16" 1 1/8" 2 1/2" 3/8" 150 12
K3100CU - 3/4 3/4" 3/8" - 16 1 15/16" 1 1/2" 1 1/8" 2 1/2" 7/16" 250 12
K3100CU - 1 1" 3/8" - 16 2 5/16" 1 3/4" 1 5/16" 2 1/2" 9/16" 250 22
K3100CU - 1 1/4 1 1/4" 3/8" - 16 2 3/4" 2 1/16" 1 9/16" 2 1/2" 9/16" 250 24
K3100CU - 1 1/2 1 1/2" 3/8" - 16 3 5/16" 2 7/16" 2 1/16" 2 1/2" 15/16" 250 30
K3100CU - 2 2" 3/8" - 16 4 1/2" 3 7/16" 3 3/8" 2 1/2" 1 3/4" 250 35
K3100CU - 2 1/2 2 1/2" 1/2" - 13 5 11/16" 4 1/2" 3 15/16" 2 1/2" 2 1/8" 350 80
K3100CU - 3 3" 1/2" - 13 5 3/16" 3 5/8" 4" 2 1/2" 2 1/16" 350 88
K3100CU - 3 1/2 3 1/2" 1/2" - 13 6 1/2" 4 9/16" 4 1/8" 2 1/2" 2 1/8" 350 94
K3100CU - 4 4" 1/2" - 13 7 3/8" 3 5/16" 4 3/8" 2 1/2" 2 1/8" 400 116
K3100CU - 5 5" 1/2" - 13 9" 6 7/16" 5 3/4" 2 1/2" 2 1/2" 550 208
K3100CU - 6 6" 5/8" - 11 10 5/16" 7 1/4" 6 1/2" 2 1/2" 3" 550 247
Material: Steel Standard Finish: Copper Service: Designed for suspending cop- per tubing allowing for vertical adjust- ment. (Available with plastic coasting to provide additional separation between tubing and hanger) Ordering: Specify part number and fin- ish
K3100CUPVC - Plastic Coated
Part Number
Rod Take-Out "D" "E"
Wt./C (Lbs.)
K3102 - 4 4" 5/8" - 11 8 5/16" 5 13/16" 4 5/8" 2 1/2" 2" 1430 203
K3102 - 6 6" 3/4" - 10 10 5/8" 7 1/16" 5 13/16" 3" 2" 1940 352
K3102 - 8 8" 3/4" - 10 13 1/4" 8 5/8" 7 3/16" 3 1/2" 2 1/8" 2000 532
K3102 - 10 10" 7/8" - 9 15 7/8" 10 1/4" 8 11/16" 3 1/2" 2 1/4" 3600 800
K3102 - 12 12" 7/8" - 9 18" 11 5/16" 9 3/4" 3 1/2" 2 1/4" 3800 1152
K3102 - 14 14" 1" - 8 20 3/8" 12 5/8" 11 3/16 4" 2 7/8" 4200 1449
K3102 - 16 16" 1" - 8 23 1/2" 14 11/16" 12 7/8" 4" 3 3/8" 4600 2100
K3102 - 18 18" 1" - 8 25 5/8" 15 3/4" 13 15/16" 4 1/2" 3 3/8" 4800 2294
K3102 - 20 20" 1 1/4" - 7 29 1/2" 18 9/16" 17 7/16" 5" 4 13/16" 4800 3887
K3102 - 24 24" 1 1/4" - 7 33" 19 1/8" 20" 5" 5 1/4" 4800 4844
Material: Steel (Stainless Steel available) Standard Finish: Plain or Electro-Plated
Service: Designed for suspending stationary duc- tile iron and cast iron pipe allowing for vertical adjustment Ordering: Specify part number and finish
Note: For pipe sizes 12” and larger, cross bolt sleeve is included
134
V Bottom Clevis Hanger - K3106
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for suspending flexible plastic pipe. Use with K3106V Plastic Pipe Support Channel Ordering: Specify part number and finish
Part Number Nominal Pipe Size Rod Size
"A" "B" "C" "E" Design
Load (Lbs.) Wt./C (Lbs.)
4" 5 11/16"
Pipe Support Channel - K3106V
Material: Steel Standard Finish: Pre-Galvanized Service: Designed as a continuous support for plastic or other flexible pipe systems. Use with K3106 V Bottom Clevis Hanger. Hangers should be located as close as possible to the channel joints Ordering: Specify part number and finish
Part Number For Nominal Pipe Size "B" Design Load (Lbs.) Wt./C (Lbs.)
K3106V - 1 1/2" to 2" 1 1/2" 150 540
K3106V - 2 2 1/2" to 4" 3" 250 1080
136
Adjustment "F" "H"
Design Load (Lbs.)
Wt./C (Lbs.)
K3108 - 3/4 3/4" 3/8" - 16 4 3/8" 3 13/16" 3 1/16" 2 1/2" 1/2" 2" 730 45
K3108 - 1 1" 3/8" - 16 4 3/4" 4 1/16" 3 1/4" 2 1/2" 5/8" 2" 730 49
K3108 - 1 1/4 1 1/4" 3/8" - 16 5 3/8" 4 1/2" 3 5/16" 2 1/2" 7/8" 2" 730 55
K3108 - 1 1/2 1 1/2" 3/8" - 16 6 7/8" 5 15/16" 5 1/8" 2 1/2" 1 3/16" 2" 730 67
K3108 - 2 2" 3/8" - 16 8 13/16" 7 5/8" 6 7/8" 2 1/2" 1 5/8" 4" 730 83
K3108 - 2 1/2 2 1/2" 1/2" - 13 10" 8 1/2" 7 9/16" 2 1/2" 2" 4" 1350 177
K3108 - 3 3" 1/2" - 13 10 5/8" 8 13/16" 7 7/8" 2 1/2" 2" 4" 1350 191
K3108 - 4 4" 5/8" - 11 11 13/16" 9 1/2" 8 3/8" 2 1/2" 2" 4" 1430 237
K3108 - 5 5" 5/8" - 11 13 1/8" 10 5/16" 9 1/8" 2 1/2" 2" 4" 1430 302
K3108 - 6 6" 3/4" - 10 14 3/8" 11" 9 11/16" 3" 2" 4" 1940 397
K3108 - 8 8" 3/4" - 10 16 3/4" 12 3/8" 11 1/8" 3 1/2" 2 5/16" 4" 2000 582
K3108 - 10 10" 7/8" - 9 19 1/4" 13 13/16" 12 5/16" 3 1/2" 2 5/16" 4" 3600 968
K3108 - 12 12" 7/8" - 9 21 5/8" 15 3/16" 13 5/8" 3 1/2" 2 5/8" 4" 3800 1221
Material: Steel (Stainless Steel available) Standard Finish: Plain or Electro-Plated Service: Designed for suspending insulated pipe allowing for vertical adjustment Ordering: Specify part number and finish. For Service temperature of 750°F thru 1050°F specify Stainless Steel
Note: Hangers are sized to nominal pipe size - allowance must be made for insulation thickness
137
Rod Take-Out "D"
Design Load (Lbs.)
Wt./C (Lbs.)
K3109 - 2 2" 3/8" - 16 3 13/16" 2 5/8" 1 7/8" 300 52
K3109 - 2 1/2 2 1/2" 1/2" - 13 4 5/8" 3 3/16" 2 3/16" 500 116
K3109 - 3 3" 1/2" - 13 5 5/16" 3 9/16" 2 5/8" 500 133
K3109 - 3 1/2 3 1/2" 1/2" - 13 5 13/16" 3 13/16" 2 7/8" 500 145
K3109 - 4 4" 5/8" - 11 6 1/2" 4 1/4" 3 1/8" 700 180
K3109 - 5 5" 5/8" - 11 7 13/16" 5" 3 7/8" 700 248
K3109 - 6 6" 3/4" - 10 9 7/16" 5 11/16" 4 7/16" 900 332
K3109 - 8 8" 3/4" - 10 11 3/8" 7" 5 13/16" 1000 513
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for suspending non- insulated, stationary pipe where space is limited Ordering: Specify part number and size
138
(Lbs.) Wt./C (Lbs.)
K3170 - 1/2 1/2" 3/8" - 16 2 7/16" 1 3/16" 1 1/4" 180 11
K3170 - 3/4 3/4" 3/8" - 16 2 1/2" 1 1/4" 1 1/4" 180 12
K3170 - 1 1" 3/8" - 16 2 5/8" 1 3/8" 1 1/4" 180 13
K3170 - 1 1/4 1 1/4" 3/8" - 16 2 7/8" 1 5/8" 1 1/4" 180 14
K3170 - 1 1/2 1 1/2" 3/8" - 16 3" 1 3/4" 1 1/4" 180 14
K3170 - 2 2" 3/8" - 16 3 7/16" 2 3/16" 1 1/2" 180 16
K3170 - 2 1/2 2 1/2" 3/8" - 16 3 7/8" 2 5/8" 1 11/16" 200 25
K3170 - 3 3" 3/8" - 16 4 1/4" 3" 1 3/4" 250 29
K3170 - 3 1/2 3 1/2" 3/8" - 16 4 5/8" 3 3/8" 1 7/8" 300 33
K3170 - 4 4" 3/8" - 16 5" 3 3/4" 2" 360 40
K3170 - 5 5" 1/2" - 13 5 9/16" 4 1/16" 1 3/4" 480 83
K3170 - 6 6" 1/2" - 13 6 7/16" 4 15/16" 2 3/16" 630 91
K3170 - 8 8" 1/2" - 13 7 11/16" 6 3/16" 2 7/16" 970 130
Material: Steel Standard Finish: Pre-Galvanized Service: Designed for suspending insu- lated pipe (with shield) or non-insulated pipe allowing for vertical adjustment Ordering: Specify part number and finish
Notes: Knurled nut available as K3170KN-(rod size). Specify the K3170 part number it will be used in when ordering
139
Part Number Nominal
Tubing Size Rod Size "A" "B" "C" "D" Design Load
(Lbs.) Wt./C (Lbs.)
K3170CT - 1/2 1/2" 3/8" - 16 2 1/16" 1 1/8" 31/32" 180 8
K3170CT - 3/4 3/4" 3/8" - 16 2 5/16" 1 5/16" 1 1/32" 180 10
K3170CT - 1 1" 3/8" - 16 2 1/2" 1 9/16" 1 5/32" 180 10
K3170CT - 1 1/4 1 1/4" 3/8" - 16 2 1/2" 1 9/16" 1" 180 12
K3170CT - 1 1/2 1 1/2" 3/8" - 16 2 15/16" 2" 1 5/16" 180 12
K3170CT - 2 2" 3/8" - 16 3 1/8" 2 1/8" 1 3/16" 180 12
K3170CT - 2 1/2 2 1/2" 1/2" - 13 4 1/16" 2 9/16" 1 3/8" 200 31
K3170CT - 3 3" 1/2" - 13 3 15/16" 3 3/4" 1 1/4" 250 33
K3170CT - 3 1/2 3 1/2" 1/2" - 13 4 7/16" 3 1/4" 1 1/2" 300 38
K3170CT - 4 4" 1/2" - 13 4 11/16" 3 9/16" 1 9/16" 360 40
K3170CT - 5 5" 1/2" - 13 5 15/16" 4 5/16" 1 25/32" 480 95
K3170CT - 6 6" 1/2" - 13 6 11/16" 5 3/16" 2 1/8" 630 118
Material: Steel Standard Finish: Copper Service: Designed for suspending copper tubing, allowing for vertical adjustment (available with plastic coasting to provide additional separation between tubing and hanger) Ordering: Specify part number, rod size and finish
K3170CUPVC - Plastic Coated
Rod Size "A" "B" "C" "D" "E" "F"
Design Load (Lbs.)
Wt./C (Lbs.)
K3172 - 1/2 1/2" 3/8" - 16 2 5/8" 2 3/16" 1 7/16" 1 1/4" 2 1/2" 610 11
K3172 - 3/4 3/4" 3/8" - 16 2 5/8" 2 1/16" 1 5/16" 1" 2 1/2" 610 12
K3172 - 1 1" 3/8" - 16 2 11/16" 2 1/16" 1 5/16" 11/16" 2 1/2" 610 12
K3172 - 1 1/4 1 1/4" 3/8" - 16 3 7/16" 2 9/16" 1 13/16" 1 1/4" 2 1/2" 610 14
K3172 - 1 1/2 1 1/2" 3/8" - 16 3 11/16" 2 3/4" 2" 1 3/16" 2 1/2" 610 16
K3172 - 2 2" 3/8" - 16 4 3/16" 3" 2 1/4" 1 3/16" 2 1/2" 610 23
K3172 - 2 1/2 2 1/2" 1/2" - 13 4 7/8" 3 7/16" 2 7/16" 1 1/4" 3 1/2" 970 28
K3172 - 3 3" 1/2" - 13 6" 4 1/4" 3 1/4" 1 5/8" 3 1/2" 970 41
K3172 - 3 1/2 3 1/2" 1/2" - 13 6 1/8" 4 1/8" 3 1/8" 1 3/8" 3 1/2" 970 44
K3172 - 4 4" 1/2" - 13 6 3/4" 4 1/2" 3 1/4" 1 3/8" 3 1/2" 1250 81
K3172 - 5 5" 1/2" - 13 7 3/4" 5" 4 3/4" 1 1/4" 4" 1250 100
K3172 - 6 6" 3/4" - 10 10" 6 11/16" 5 3/16" 2 1/8" 4 1/2" 1600 160
K3172 - 8 8" 3/4" - 10 11 7/8" 7 9/16" 6 13/16" 2" 4 1/2" 1800 260
Material: Steel (Stainless Steel available) Standard Finish: Plain or Pre-Galvanized Service: Designed for suspending non-insulated pipe allowing for vertical adjustment. Ordering: Specify part number and finish
K3172PVC - Plastic Coated
141
Material: Steel Standard Finish: Copper Service: Designed for suspend- ing copper tubing allowing for vertical adjustment. (Available with plastic coating to provide additional separation between tubing and hanger) Ordering: Specify part number and finish
K3172CUPVC - Plastic Coated
Design Load (Lbs.)
Wt./C (Lbs.)
K3172CU - 1/2 1/2" 3/8" - 16 9/16" 2 1/4" 1 1/2" 1 7/16" 2 1/2" 610 12
K3172CU - 3/4 3/4" 3/8" - 16 2 9/16" 2 1/8" 1 3/8" 1 3/16" 2 1/2" 610 12
K3172CU - 1 1" 3/8" - 16 2 9/16" 2" 1 1/4" 15/16" 2 1/2" 610 12
K3172CU - 1 1/4 1 1/4" 3/8" - 16 2 3/4" 2 1/16" 1 5/16" 7/8" 2 1/2" 610 12
K3172CU - 1 1/2 1 1/2" 3/8" - 16 3 1/8" 2 5/16" 1 9/16" 1" 2 1/2" 610 13
K3172CU - 2 2" 3/8" - 16 3 11/16" 2 5/8" 1 7/8" 1 1/16" 2 1/2" 610 16
K3172CU - 2 1/2 2 1/2" 1/2" - 13 4 1/2" 3 3/16" 2 5/16" 1 1/4" 2 1/2" 970 30
K3172CU - 3 3" 1/2" - 13 5" 3 7/16" 2 1/2" 1 3/16" 2 1/2" 970 32
K3172CU - 3 1/2 3 1/2" 1/2" - 13 5 3/4" 3 15/16" 3" 1 7/16" 2 1/2" 970 40
K3172CU - 4 4" 1/2" - 13 6 1/4" 4 3/16" 3 1/4" 1 7/16" 2 1/2" 970 49
142
Offset J-Hook - K3190
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for supporting light pipe runs with a 1” offset from mounting surfaces Ordering: Specify part number and finish
Part Number Nominal Pipe Size "A" "B" Design Load (Lbs.) Wt./C (Lbs.)
K3190 - 1/2 1/2" 1 15/32" 6 25/32" 200 56
K3190 - 3/4 3/4" 1 9/16" 6 7/8" 200 59
K3190 - 1 1" 1 11/16" 7 1/16" 200 81
K3190 - 1 1/4 1 1/4" 1 7/8" 7 1/4" 200 86
K3190 - 1 1/2 1 1/2" 1 31/32" 7 11/32" 200 89
K3190 - 2 2" 2 7/32" 7 19/32" 200 96
K3190 - 2 1/2 2 1/2" 2 15/32" 7 27/32" 350 125
K3190 - 3 3" 2 25/32" 8 5/32" 350 134
K3190 - 4 4" 3 9/32" 8 25/32" 450 226
143
Straight J-Hook - K3191
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for supporting light pipe runs which require no clearance between mounting surfaces Ordering: Specify part number, size and finish
Part Number Nominal Pipe Size "A" "B" Design Load (Lbs.) Wt./C (Lbs.)
K3191 - 1/2 1/2" 21/32" 6 25/32" 200 54
K3191 - 3/4 3/4" 3/4" 6 7/8" 200 56
K3191 - 1 1" 15/16" 7 1/16" 200 78
K3191 - 1 1/4 1 1/4" 1 1/8" 7 1/4" 200 84
K3191 - 1 1/2 1 1/2" 1 7/32" 7 11/32" 200 86
K3191 - 2 2" 1 15/32" 7 19/32" 200 93
K3191 - 2 1/2 2 1/2" 1 23/32" 7 27/32" 350 120
K3191 - 3 3" 2 1/32" 8 3/8" 350 134
K3191 - 4 4" 2 21/32" 8 25/32" 450 223
144
Hinged Extension Split Pipe Clamp- K3198H
Part Number Nominal Pipe Size Rod Size "A" "C" Design Load (Lbs.) Wt./C (Lbs.)
K3198H - 3/8 3/8" 3/8" - 16 31/32" 180 9
K3198H - 1/2 1/2" 3/8" - 16 1 1/16" 180 12
K3198H - 3/4 3/4" 3/8" - 16 1 7/32" 180 12
K3198H - 1 1" 3/8" - 16 1 11/32" 180 13
K3198H - 1 1/4 1 1/4" 3/8" - 16 1 19/32" 180 18
K3198H - 1 1/2 1 1/2" 3/8" - 16 1 23/32" 180 21
K3198H - 2 2" 3/8" - 16 2" 180 44
K3198H - 2 1/2 2 1/2" 1/2" - 13 2 11/32" 300 73
K3198H - 3 3" 1/2" - 13 2 23/32" 300 95
Material: Malleable Iron Standard Finish: Plain or Electro-Plated Service: Designed for suspending non-insulated pipe horizontally or vertically Ordering: Specify part number and finish
145
Part Number Nominal Tubing Size Rod Size "A" "C" Design Load
(Lbs.) Wt./C (Lbs.)
K3198HCT - 1/2 1/2" 3/8" - 16 5/8" 180 8
K3198HCT - 3/4 3/4" 3/8" - 16 13/16" 180 10
K3198HCT - 1 1" 3/8" - 16 15/16" 180 10
K3198HCT - 1 1/4 1 1/4" 3/8" - 16 1 1/8" 180 14
K3198HCT - 1 1/2 1 1/2" 3/8" - 16 1 9/16" 180 18
K3198HCT - 2 2" 3/8" - 16 1 7/8" 180 23
Hinged Extension Split Pipe Clamp - K3198HCU
Material: Malleable Iron Standard Finish: Copper Service: Designed for suspending copper tubing horizontally or vertically Ordering: Specify part number and finish
146
Part Number Nominal Pipe
(Lbs.) Wt./C (Lbs.)
K3198R - 1/2 1/2" 3/8" - 16 1 1/16" 180 16
K3198R - 3/4 3/4" 3/8" - 16 1 7/32" 180 18
K3198R - 1 1" 3/8" - 16 1 11/32" 180 24
K3198R - 1 1/4 1 1/4" 3/8" - 16 1 19/32" 180 29
K3198R - 1 1/2 1 1/2" 3/8" - 16 1 23/32" 180 32
K3198R - 2 2" 3/8" - 16 2" 180 39
K3198R - 2 1/2 2 1/2" 1/2" - 13 2 11/32" 300 115
K3198R - 3 3" 1/2" - 13 2 23/32" 300 140
K3198R - 4 4" 1/2" - 13 3 11/32" 300 160
Material: Malleable Iron (Stainless Steel available) Standard Finish: Plain or Electro-Plated Service: Designed for suspending non-insulated pipe horizontally Ordering: Specify part number and finish.
147
2 Screw Extension Split Pipe Clamp - K3198CU
Part Number Nominal Tubing Size Rod Size "A" "C" Design Load (Lbs.) Wt./C (Lbs.)
K3198RCT - 3/8 3/8" 3/8" - 16 11/16" 180 12
K3198RCT - 1/2 1/2" 3/8" - 16 1 11/16" 180 12
K3198RCT - 3/4 3/4" 3/8" - 16 7/8" 180 14
K3198RCT - 1 1" 3/8" - 16 1 1/16" 180 17
K3198RCT - 1 1/4 1 1/4" 3/8" - 16 1 1/8" 180 17
K3198RCT - 1 1/2 1 1/2" 3/8" - 16 1 5/16" 180 22
K3198RCT - 2 2" 3/8" - 16 1 1/2" 180 26
Material: Malleable Iron Standard Finish: Copper Service: Designed for suspending copper tubing horizontally Ordering: Specify part number and finish
148
Rod Take Out "D"
Diameter "E" Bolt Size
Wt./C (Lbs.)
K3690 - 1/2 1/2" 3/8" - 16 2 3/32" 1" 1 11/16" 13/32" 1/4" - 20 x 2" 400 20
K3690 - 3/4 3/4" 3/8" - 16 2 11/32" 1" 1 13/16" 13/32" 1/4" - 20 x 2 1/4" 400 23
K3690 - 1 1" 3/8" - 16 2 19/32" 1" 1 15/16" 13/32" 1/4" - 20 x 2 1/2" 400 24
K3690 - 1 1/4 1 1/4" 3/8" - 16 2 13/16" 1" 2" 13/32" 1/4" - 20 x 2 3/4" 400 27
K3690 - 1 1/2 1 1/2" 3/8" - 16 3 1/16" 1" 2 1/8" 13/32" 1/4" - 20 x 3" 400 29
K3690 - 2 2" 3/8" - 16 3 1/2" 1" 2 5/16" 13/32" 1/4" - 20 x 3 1/2" 400 32
K3690 - 2 1/2 2 1/2" 1/2" - 13 4 7/16" 1" 3" 9/16" 3/8" - 16 x 4 1/2" 800 71
K3690 - 3 3" 1/2" - 13 4 7/8" 1" 3 1/8" 9/16" 3/8" - 16 x 5" 800 77
K3690 - 3 1/2 3 1/2" 1/2" - 13 5 3/16" 1" 3 3/16" 9/16" 3/8" - 16 x 5 1/2" 800 84
K3690 - 4 4" 5/8" - 11 6 1/8" 1 1/4" 3 7/8" 9/16" 3/8" - 16 x 6 1/2" 800 139
K3690 - 5 5" 5/8" - 11 6 3/4" 1 1/2" 4" 9/16" 3/8" - 16 x 7 1/2" 800 166
K3690 - 6 6" 3/4" - 10 7 3/4" 1 3/16" 4 7/16" 9/16" 3/8" - 16 x 8 1/2" 1000 226
K3690 - 8 8" 3/4" - 10 9 1/4" 1" 4 15/16" 9/16" 3/8" - 16 x 10 1/2" 1200 332
Adjustable “J” Hanger - K3690
Material: Steel Standard Finish: Electro-Plated (Hot-Dip Galvanized available with Electro-Plated hardware) Service: Designed for suspending insulated pipe (with shield) and non-insulated pipe allowing for vertical adjustment. Side hole permits wall mounting Ordering: Specify part number and finish
K3690PVC - Plastic Coated
Pipe Clamps
Pipe clamps presented in this section are designed for support and attachment of pipe to structural steel. Various types of pipe clamps and sizes are available for nu- merous applications. Materials: Carbon Steel is used in the manufacturing of riser and pipe clamps. Stainless Steel and other materials are also available. Finishes: Finishes for pipe supports in this section are Plain Steel, Electro-Plated Zinc, Hot Dipped Galvanized, Red Primer, Plastic Coating, Copper Plated, Stainless Steel and other special coatings are also available. Notes: All hangers in this section are sized to fit schedule 40/80 pipe unless other- wise noted. Some steel items may be specially fabricated to accommodate other pipe diameters. Products in this section are designed and manufactured in accor- dance with industry standards. RHK is not responsible for injuries and damage which could result from improper and negligent installation of the items.
115
Design Load 1 (Lbs.)
Design Load 2 (Lbs.)
Design Load 3 (Lbs.)
Wt./C (Lbs.)
K2400 - 1/2 1/2" 5/16" 7/16" 2 13/16" 10 Ga. 1 5/8" 600 150 105 23
K2400 - 3/4 3/4" 5/16" 7/16" 3" 10 Ga. 1 5/8" 600 150 105 26
K2400 - 1 1" 5/16" 7/16" 3 17/32" 10 Ga. 1 5/8" 600 150 120 31
K2400 - 1 1/4 1 1/4" 5/16" 7/16" 3 3/4" 10 Ga. 1 5/8" 600 150 120 36
K2400 - 1 1/2 1 1/2" 5/16" 7/16" 4 1/16" 10 Ga. 1 5/8" 600 150 120 39
K2400 - 2 2" 7/16" 11/16" 5 21/32" 1/4" 1 5/8" 1200 480 180 93
K2400 - 2 1/2 2 1/2" 7/16" 11/16" 6 5/32" 1/4" 1 5/8" 1200 480 180 106
K2400 - 3 3" 7/16" 11/16" 6 25/32" 1/4" 1 5/8" 1200 480 300 132
K2400 - 3 1/2 3 1/2" 7/16" 11/16" 7 9/32" 1/4" 1 5/8" 1200 480 300 151
K2400 - 4 4" 9/16" 11/16" 7 25/32" 1/4" 1 5/8" 1500 600 450 160
K2400 - 5 5" 9/16" 11/16" 8 7/8" 1/4" 1 5/8" 1500 600 450 192
K2400 - 6 6" 9/16" 11/16" 9 15/16" 1/4" 1 5/8" 1500 600 450 219
K2400 - 8 8" 9/16" 11/16" 11 31/32" 1/4" 1 5/8" 2000 800 600 297
K2400 - 10 10" 9/16" 11/16" 14" 1/4" 1 5/8" 2000 800 600 465
K2400 - 12 12" 9/16" 11/16" 16" 1/4" 1 5/8" 2000 800 600 560
K2400 - 14 14" 15/16" 1 5/16" 20 3/8" 3/8" 1 3/4" 2000 800 600 761
K2400 - 16 16" 15/16" 1 5/16" 22 3/8" 3/8" 1 3/4" 2000 800 600 861
K2400 - 18 18" 15/16" 1 5/16" 26 1/8" 1/2" 1 3/4" 2000 800 600 1297
K2400 - 20 20" 15/16" 1 5/16" 28 1/8" 1/2" 1 3/4" 2000 800 600 1426
K2400 - 24 24" 15/16" 1 5/16" 32 1/8" 1/2" 1 3/4" 2000 800 600 1682
Material: Steel (Stainless Steel available) Standard Finish: Plain or Electro- Plated Service: Designed for supporting pipe runs from strut supports Ordering: Specify part number and finish
Note: Ductile iron sizes available
Design Load 2
Two-Bolt Underground Clamp - K3132
Material: Steel Standard Finish: Plain or Electro-Plated (Hot-Dip Galvanized available) Service: Designed to prevent separation of caulked joints on AWWA ductile iron water pipes Ordering: Specify part number and finish (Order K3132W Lug Washers, Tie Rods, and Hex Nuts separately
Part Number Nominal Pipe Size "A" "B" Clamp "I.D." Bolt Size Wt./C (Lbs.)
K3132 - 4 4" 12 7/8" 9 3/4" 5" 5/8" - 11 x 3" 864
K3132 - 6 6" 14 3/4" 12" 7 1/16" 5/8" - 11 x 3" 1020
K3132 - 8 8" 17 1/4" 14 1/4" 9 3/16" 5/8" - 11 x 3" 1222
K3132 - 10 10" 19 3/8" 16 1/2" 11 3/8" 5/8" - 11 x 3" 1409
K3132 - 12 12" 21 7/8" 18 7/8" 13 1/2" 5/8" - 11 x 3" 1608
K3132 - 14 14" 26" 22 1/4" 15 3/4" 7/8" - 9 x 4 1/2" 4359
K3132 - 16 16" 28 3/8" 24 5/8" 17 7/8" 1" - 8 x 4 1/2" 6403
K3132 - 18 18" 31 3/8" 27 5/8" 20" 1 1/4" - 7 x 5" 7293
K3132 - 20 20" 33 1/2" 29 3/4" 22 1/8" 1 1/4" - 7 x 5" 8778
K3132 - 24 24" 39" 35 1/4" 26 3/8" 1 1/4" - 6 x 5 1/2" 11659
117
Pipe Size Diameter "D" "E" "G" "H" Wt./C (Lbs.)
K3132W - 3/4 3/4" - 10 4" to 12" 7/8" 2 3/8" 5/8" 4 5/8" 74
K3132W - 1 1" - 8 14" to 16" 1 1/8" 3 1/2" 5/8" 2 1/2" 207
K3132W - 1 1/4 1 1/4" - 7 18" 1 3/8" 3 1/2" 5/8" 3 1/2" 236
K3132W - 1 3/8 1 3/8" - 6 20" 1 1/2" 4" 5/8" 4" 231
K3132W - 1 1/2 1 1/2" - 6 24" 1 5/8" 4" 5/8" 4" 259
Material: Ductile iron for K3132W - 3/4, steel for other sizes Standard Finish: Plain or Electro-Plated Service: Designed to use with K3132 Two- Bolt Underground Clamp for aligning and securing tie rods Ordering: Specify part number and finish
118
Four Bolt Underground Clamp - K3134
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed to prevent separation of caulked joints on AWWA ductile iron water pipes Ordering: Specify part number and finish (Order K3134W Washer, Tie Rods and Hex Nuts separately)
Part Number
Maximum Test Pressure
Wt./C (Lbs.)
K3134 - 4 4" 14 7/16" 9 5/8" 5" 5/8" - 11 x 3" 250 4550 1012
K3134 - 6 6" 16 7/8" 11 7/8" 7 1/8" 5/8" - 11 x 3" 250 9340 1204
K3134 - 8 8" 19 1/8" 14 1/8" 9 5/16" 5/8" - 11 x 3 1/2" 250 16080 2091
K3134 - 10 10" 21 3/8" 16 5/8" 11 1/2" 3/4" - 10 x 4" 250 24180 2466
K3134 - 12 12" 25 1/8" 19 5/8" 13 1/2" 7/8" - 9 x 4" 250 34230 3537
K3134 - 14 14" 28 1/4" 22 1/4" 15 3/4" 7/8" - 9 x 4 1/2" 120 22200 4718
K3134 - 16 16" 32 1/8" 26 1/4" 17 7/8" 1" - 8 x 4 1/2" 115 27760 7155
K3134 - 18 18" 35 1/8" 28 1/8" 20" 1 1/4" - 7 x 5" 100 23900 8179
K3134 - 20 20" 37 3/4" 30 1/2" 22 1/8" 1 1/4" - 7 x 5" 75 27500 9856
K3134 - 24 24" 44 1/4" 36" 26 3/8" 1 1/2" - 6 x 5 1/2" 50 26200 13384
119
Pipe Size Diameter
"D" "E" "F" Wt./C (Lbs.)
K3134W - 3/4 3/4" - 10 4" to 8" 7/8" 3" 1/2" 119
K3134W - 1 1" - 8 10" to 12" 1 1/8" 3 1/2" 1/2" 159
K3134W - 1 1/8 1 1/8" - 7 14" to 16" 1 1/4" 3 1/2" 5/8" 181
K3134W - 1 1/4 1 1/4" - 7 18" 1 3/8" 4" 3/4" 229
K3134W - 1 3/8 1 3/8" - 6 20" 1 1/2" 4" 3/4" 223
K3134W - 1 1/2 1 1/2" - 6 24" 1 5/8" 4 1/2" 3/4" 217
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for use with K3134 Four-Bolt Underground Clamp to secure tie rods Ordering: Specify part number and finish
120
Part Number Nominal Pipe Size "A" "B" "C" Bolt Size
Maximum Design Load for Service
Temperature 650°F (Lbs.)
Temperature 750°F (Lbs.)
Wt./C (Lbs.)
K3140 - 1/2 1/2" 3/8" 31/32" 1 17/32" 5/16" - 18 x 1 1/4" 500 390 30
K3140 - 3/4 3/4" 9/16" 1 3/32" 1 21/32" 5/16" - 18 x 1 1/4" 500 390 31
K3140 - 1 1" 9/16" 1 5/16" 1 7/8" 5/16" - 18 x 1 1/4" 500 390 32
K3140 - 1 1/4 1 1/4" 17/32" 1 7/16" 2" 5/16" - 18 x 1 1/4" 500 390 39
K3140 - 1 1/2 1 1/2" 19/32" 1 21/32" 2 7/32" 5/16" - 18 x 1 1/4" 800 620 41
K3140 - 2 2" 9/16" 2 1/8" 2 3/4" 1/2" - 13 x 2" 1040 810 118
K3140 - 2 1/2 2 1/2" 5/8" 2 21/32" 3 9/32" 1/2" - 13 x 2" 1040 810 130
K3140 - 3 3" 5/8" 2 15/16" 3 9/16" 1/2" - 13 x 2" 1040 810 150
K3140 - 3 1/2 3 1/2" 5/8" 3 5/32" 3 25/32" 1/2" - 13 x 2" 1040 810 158
K3140 - 4 4" 3/4" 3 9/16" 4 5/16" 5/8" - 11 x 2 1/4" 1040 810 239
K3140 - 5 5" 3/4" 4 1/8" 4 7/8" 5/8" - 11 x 2 1/4" 1040 810 272
K3140 - 6 6" 7/8" 4 15/16" 5 13/16" 3/4" - 10 x 2 3/4" 1615 1260 541
K3140 - 8 8" 1" 6 1/16" 6 15/16" 3/4" - 10 x 3" 1615 1260 642
K3140 - 10 10" 1" 7 3/8" 8 11/16" 7/8" - 9 x 3 1/2" 2490 1950 1366
K3140 - 12 12" 1" 8 7/16" 9 3/4" 7/8" - 9 x 3 1/2" 2490 1950 1543
K3140 - 14 14" 1 1/8" 9 1/4" 10 5/8" 7/8" - 9 x 3 1/2" 2490 1950 2077
K3140 - 16 16" 1 1/8" 10 1/4" 11 5/8" 7/8" - 9 x 3 1/2" 2490 1950 2289
K3140 - 18 18" 1 1/4" 11 7/8" 13 1/4" 1" - 8 x 4" 3060 2390 3206
K3140 - 20 20" 1 3/8" 12 3/4" 14 1/8" 1 1/8" - 7 x 4 1/2" 3060 2390 3616
K3140 - 24 24" 1 5/8" 15 1/4" 16 7/8" 1 1/4" - 7 x 5" 3060 2390 5161
K3140 - 30 30" 2 1/4" 18 5/8" 21" 1 1/2" - 6 x 6" 3500 2740 10460
Material: Steel (Stainless Steel available) Standard Finish: Plain, Electro-Plated, or Hot-Dip Galva- nized Service: Designed for suspending non-insulated pipe runs (Use with K3200 Weldless Eye Nut, K3210 Eye Rod, or K3211 Welded Eye Rod) Ordering: Specify part number and finish
121
Part Number
Maximum Design Load for Service
Temperature 650°F (Lbs.)
Temperature 750°F (Lbs.)
Wt./C (Lbs.)
K3142 - 3 3" 1" 3 1/8" 4 1/8" 3/4" - 10 x 2 3/4" 3370 2640 404
K3142 - 4 4" 1" 3 3/4" 5 1/16" 7/8" - 9 x 3" 3515 2750 616
K3142 - 5 5" 1" 4 3/8" 5 11/16" 7/8" - 9 x 3" 3515 2750 687
K3142 - 6 6" 1 1/8" 5 1/4" 6 1/4" 1" - 8 x 3 1/2" 4865 3800 1293
K3142 - 8 8" 1 1/8" 6 1/4" 7 3/4" 1" - 8 x 4" 4865 3800 1523
K3142 - 10 10" 1 1/4" 7 11/16" 9 1/16" 1 1/4" - 7 x 4" 6010 4700 2348
K3142 - 12 12" 1 5/8" 9 1/8" 10 3/4" 1 1/4" - 7 x 5" 8675 6770 3749
K3142 - 14 14" 1 5/8" 10 1/8" 12" 1 1/2" - 6 x 5 1/2" 9120 7140 5011
K3142 - 16 16" 1 5/8" 11" 12 7/8" 1 3/4" - 5 x 5 1/2" 9120 7140 5885
K3142 - 18 18" 3" 14 1/2" 18 1/2" 2" - 4 1/2 x 7" 13800 10800 12902
K3142 - 20 20" 3" 16" 20" 2" - 4 1/2 x 7" 15300 11900 15113
K3142 - 24 24" 3 1/4" 18 1/2" 23" 2" - 4 1/2 x 8" 16300 12700 20561
K3142 - 30 30" 3 1/2" 22 1/2" 27 1/2" 2 1/4" - 4 1/2 x 9" 20500 16000 36658
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for suspending non- insulated, heavy-duty pipe runs (use with K3200 Weldless Eye Nut, K3210 Eye Rod or K3211 Welded Eye Rod) Ordering: Specify part number and finish
122
Double Bolt Pipe Clamp - K3144...
Part Number Nominal Pipe Size "A" Bolt Size "B¹" Bolt Size "B²" "C"
K3144 - 3/4 3/4" 5/8" 3/8" - 16 x 1 3/4" 1/2" - 13 x 2" 1 3/8"
K3144 - 1 1" 5/8" 3/8" - 16 x 1 3/4" 1/2" - 13 x 2" 1 3/8"
K3144 - 1 1/4 1 1/4" 5/8" 3/8" - 16 x 1 3/4" 1/2" - 13 x 2" 1 1/2"
K3144 - 1 1/2 1 1/2" 1 1/16" 1/2" - 13 x 2 1/2" 5/8" - 11 x 2 1/2" 1 13/16"
K3144 - 2 2" 1 1/16" 1/2" - 13 x 2 1/2" 5/8" - 11 x 2 1/2" 2 1/8"
K3144 - 2 1/2 2 1/2" 1 1/16" 1/2" - 13 x 2 1/2" 5/8" - 11 x 2 1/2" 2 3/8"
K3144 - 3 3" 1 1/16" 1/2" - 13 x 2 1/2" 5/8" - 11 x 2 1/2" 2 15/16"
K3144 - 4 4" 1 1/16" 5/8" - 11 x 2 3/4" 3/4" - 10 x 3" 3 1/2"
K3144 - 5 5" 1 1/16" 5/8" - 11 x 2 3/4" 3/4" - 10 x 3" 4"
K3144 - 6 6" 1 7/16" 3/4" - 10 x 3 1/4" 1" - 8 x 3 1/2" 5"
K3144 - 8 8" 1 7/16" 3/4" - 10 x 3 1/4" 1" - 8 x 3 1/2" 6"
K3144 - 10 10" 1 7/16" 3/4" - 10 x 3 1/4" 1" - 8 x 3 1/2" 7 1/8"
K3144 - 12 12" 1 7/16" 3/4" - 10 x 3 1/4" 1" - 8 x 3 1/2" 7 7/8"
K3144 - 14 14" 2" 1" - 8 x 4 1/2" 1 1/4" - 7 x 5" 9 1/16"
K3144 - 16 16" 2" 1" - 8 x 4 1/2" 1 1/4" - 7 x 5" 10 1/16"
K3144 - 18 18" 2" 1" - 8 x 4 1/2" 1 1/4" - 7 x 5" 11 1/16"
K3144 - 20 20" 2" 1" - 8 x 5" 1 1/4" - 7 x 5" 12 3/8"
K3144 - 24 24" 2" 1 1/8" - 7 x 5" 1 1/2" - 6 x 5 1/2" 14 3/4"
123
Temperature 650°F (Lbs.)
Temperature 750°F (Lbs.)
K3144 - 3/4 4" 4 3/4" 1 7/8" 950 740 146
K3144 - 1 4" 4 3/4" 1 7/8" 950 740 147
K3144 - 1 1/4 4" 4 3/4" 2" 950 740 152
K3144 - 1 1/2 4 1/8" 4 7/8" 2 3/8" 1545 1200 200
K3144 - 2 5 1/8" 5 7/8" 2 11/16" 1545 1200 226
K3144 - 2 1/2 5 3/8" 6 1/8" 2 15/16" 1545 1200 239
K3144 - 3 5 15/16" 6 11/16" 3 1/2" 1545 1200 264
K3144 - 4 6 1/2" 7 5/8" 4 1/2" 2500 1950 672
K3144 - 5 7" 8 1/8" 5" 2500 1950 752
K3144 - 6 8 9/16" 9 15/16" 6 1/8" 2865 2240 1158
K3144 - 8 9 9/16" 10 15/16" 7 1/8" 2865 2240 1325
K3144 - 10 10 5/8" 12" 8 1/4" 3240 2530 1505
K3144 - 12 11 5/8" 13" 9 1/4" 3240 2530 1671
K3144 - 14 12 11/16" 14 5/16" 10 11/16" 4300 3360 3666
K3144 - 16 13 11/16" 15 5/16" 11 11/16" 4300 3360 3992
K3144 - 18 14 11/16" 16 5/16" 12 11/16" 4300 3360 4330
K3144 - 20 15 7/8" 17 1/2" 14" 4500 3520 5535
K3144 - 24 17 7/8" 19 1/2" 16 3/8" 4500 3520 6590
Material: Steel (Stainless Steel available) Standard Finish: Plain or Electro-Plated Service: Designed for suspending high-temperature (maximum 750°F) pipe runs requiring up to 4” thick insulation (use with K3200 Welded Eye Rod) Ordering: Specify part number and finish. For ser- vice temperatures of 750°F thru 1050°F specify type 304 Stainless Steel
124
Heavy Duty Double Bolt Pipe Clamp - K3146
Part Number Nominal Pipe Size "A" Bolt Size "B¹" Bolt Size "B²"
K3146 - 6 6" 1 3/4" 3/4" - 10 x 3 1/2" 1" - 8 x 4"
K3146 - 8 8" 2" 3/4" - 10 x 4" 1" - 8 x 4 1/2"
K3146 - 10 10" 2 1/4" 1" - 8 x 4 1/2" 1 1/4" - 7 x 5"
K3146 - 12 12" 2 1/2" 1" - 8 x 5" 1 1/4" - 7 x 5 1/2"
K3146 - 14 14" 2 1/2" 1 1/8" - 7 x 5 1/2" 1 1/2" - 6 x 6"
K3146 - 16 16" 3" 1 1/4" - 7 x 6" 1 3/4" - 5 x 6 1/2"
K3146 - 18 18" 3 1/2" 1 1/2" - 6 x 7 1/2" 2" - 4 1/2 x 8"
K3146 - 20 20" 3 1/2" 1 1/2" - 6 x 7 1/2" 2" - 4 1/2 x 8"
K3146 - 24 24" 3 1/2" 1 1/2" - 6 x 7 1/2" 2" - 4 1/2 x 8"
K3146 - 30 30" 4 1/4" 1 3/4" - 5 x 8 1/2" 2 1/4" - 4 1/2 x 9"
Part Number "C" "D" "E" "F"
Maximum Design Load for Service
Temperature 650°F (Lbs.)
Temperature 750°F (Lbs.) Wt./C (Lbs.)
K3146 - 6 4 3/4" 8 15/16" 10 3/16" 6" 3500 2740 1182
K3146 - 8 6" 10 3/8" 11 3/8" 7 1/4" 4800 3750 1742
K3146 - 10 7 1/4" 11 3/8" 13 1/8" 9" 5500 4300 2979
K3146 - 12 8 5/8" 12 9/16" 14 5/16" 10 3/8" 8675 6790 3847
K3146 - 14 9 5/8" 13 1/2" 15 1/2" 11 5/8" 9500 7400 6104
K3146 - 16 10 7/8" 14 7/8" 17 1/8" 13 1/8" 10000 7800 7899
K3146 - 18 12 1/2" 16 1/4" 18 1/4" 14 1/2" 13800 10800 10588
K3146 - 20 13 1/2" 17 1/4" 19 3/4" 16" 15300 11900 14180
K3146 - 24 15 1/2" 19 5/16" 22 5/16" 18 1/2" 16300 12700 19145
K3146 - 30 19 7/8" 28 1/4" 32 3/4" 24 3/8" 20500 16000 34983
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for suspending heavy- duty, high temperature pipe runs requir- ing up to 4” thick insulation (use with K3200 Weldless Eye Nut, K3210 Eye Rod or K3211 Welded Eye Rod Ordering: Specify part number and finish
125
Offset Pipe Clamp - K3148
Part Number Nominal Pipe Size "A" Bolt Size "B" "C" "H"
Design Load (Lbs.)
Wt./C (Lbs.)
K3148 - 1/2 1/2" 2 1/2" 3/8" - 16 x 1 1/2" 6" 7/16" 190 106
K3148 - 3/4 3/4" 2 1/2" 3/8" - 16 x 1 1/2" 7 5/16" 7/16" 190 112
K3148 - 1 1" 2 5/8" 3/8" - 16 x 1 1/2" 7 9/16" 7/16" 190 123
K3148 - 1 1/4 1 1/4" 2 13/16" 3/8" - 16 x 1 1/2" 7 7/8" 7/16" 190 133
K3148 - 1 1/2 1 1/2" 2 15/16" 3/8" - 16 x 1 1/2" 8 1/4" 7/16" 190 140
K3148 - 2 2" 3 3/16" 3/8" - 16 x 1 3/4" 9 1/8" 7/16" 420 195
K3148 - 2 1/2 2 1/2" 3 7/16" 3/8" - 16 x 1 3/4" 10 1/2" 7/16" 420 226
K3148 - 3 3" 3 3/4" 3/8" - 16 x 1 3/4" 11 1/8" 7/16" 420 244
K3148 - 4 4" 4 1/4" 1/2" - 13 x 2" 12 1/2" 9/16" 610 358
K3148 - 5 5" 4 3/4" 1/2" - 13 x 2 1/4" 13 3/4" 9/16" 610 415
K3148 - 6 6" 5 5/16" 1/2" - 13 x 2 1/4" 16 1/2" 9/16" 870 685
K3148 - 8 8" 6 5/16" 1/2" - 13 x 2 1/2" 18 5/8" 9/16" 870 815
K3148 - 10 10" 7 3/4" 3/4" - 10 x 3" 23" 13/16" 870 2142
K3148 - 12 12" 8 3/4" 3/4" - 10 x 3" 25" 13/16" 870 2337
Material: Steel (Stainless Steel available) Standard Finish: Plain or Electro-Plated Service: Designed for supporting vertical or horizontal pipe runs at a fixed distance from a wall or structure Ordering: Specify part number
Note: Ductile and cast iron sizes are available
126
Marine Hanger - K3149
Part Number Nominal Pipe Size "A" Bolt Size "B" "C" Wt./C (Lbs.)
K3149 - 3/4 3/4" 12" 3/8" - 16 x 1 1/2" 4 7/16" 182
K3149 - 1 1" 12" 3/8" - 16 x 1 1/2" 4 11/16" 230
K3149 - 1 1/4 1 1/4" 12" 3/8" - 16 x 1 1/2" 5" 239
K3149 - 1 1/2 1 1/2" 12" 3/8" - 16 x 1 1/2" 5 1/4" 244
K3149 - 2 2" 12" 1/2" - 13 x 1 3/4" 6" 319
K3149 - 2 1/2 2 1/2" 12" 1/2" - 13 x 2" 7 1/4" 434
K3149 - 3 3" 12" 1/2" - 13 x 2" 7 7/8" 454
K3149 - 4 4" 12" 1/2" - 13 x 2" 9 1/4" 493
K3149 - 5 5" 12" 1/2" - 13 x 2" 10 1/2" 530
K3149 - 6 6" 12" 5/8" - 11 x 2 1/2" 12 1/2" 1142
K3149 - 8 8" 12" 5/8" - 11 x 2 1/2" 14 5/8" 1273
Material: Steel (Stainless Steel available) Standard Finish: Plain or Electro-Plated Service: Designed for suspending or supporting pipe runs where exact dis- tance from structure to pipe cannot be determined until installation. Field modify legs to suit conditions Ordering: Specify part number and finish
Note: Ductile and cast iron sizes are available
127
(Lbs.) Wt./C (Lbs.)
K3373 - 1/2 1/2" 9" 3/8" - 16 x 1 1/4" 255 101
K3373 - 3/4 3/4" 9 1/4" 3/8" - 16 x 1 1/4" 255 105
K3373 - 1 1" 9 9/16" 3/8" - 16 x 1 1/4" 255 109
K3373 - 1 1/4 1 1/4" 10" 3/8" - 16 x 1 1/4" 255 112
K3373 - 1 1/2 1 1/2" 10 1/4" 3/8" - 16 x 1 1/2" 255 113
K3373 - 2 2" 10 3/4" 3/8" - 16 x 1 1/2" 255 165
K3373 - 2 1/2 2 1/2" 11 1/4" 3/8" - 16 x 1 1/2" 390 180
K3373 - 3 3" 11 15/16" 3/8" - 16 x 1 1/2" 530 195
K3373 - 3 1/2 3 1/2" 12 3/8" 1/2" - 13 x 1 3/4" 670 217
K3373 - 4 4" 12 7/8" 1/2" - 13 x 1 3/4" 810 228
K3373 - 5 5" 14" 1/2" - 13 x 1 3/4" 1160 480
K3373 - 6 6" 15 3/16" 1/2" - 13 x 2" 1570 526
K3373 - 8 8" 17 3/4" 5/8" - 11 x 2 1/2" 2500 957
K3373 - 10 10" 19 7/16" 5/8" - 11 x 2 1/2" 2500 1101
K3373 - 12 12" 21 11/16" 5/8" - 11 x 3" 2700 1622
K3373 - 14 14" 23 9/16" 5/8" - 11 x 3" 2700 1732
K3373 - 16 16" 26 3/8" 3/4" - 10 x 3 1/4" 2900 2959
K3373 - 18 18" 28 7/8" 3/4" - 10 x 3 1/4" 2900 3235
K3373 - 20 20" 30 7/8" 3/4" - 10 x 3 1/2" 2900 3568
K3373 - 24 24" 34 7/8" 3/4" - 10 x 3 1/2" 2900 4064
K3373 - 30 30" 40 3/4" 7/8" - 9 x 3 1/2" 2900 6016
Material: Steel (Stainless Steel available) Standard Finish: Plain, Electro-Plated, or Hot-Dip Galvanized Service: Designed for supporting and stabilizing vertical pipe runs. Clamp is fitted for steel pipe and preferable installed below a coupling or shear lugs. Torque bolts to values given on page __ Ordering: Specify part number and finish
K3373PVC Plastic Coated
Size "L" Bolt Size Design Load (Lbs.) Wt./C (Lbs.)
K3373CT - 1/2 1/2" 8 3/4" 5/16" - 18 x 1" 75 72
K3373CT - 3/4 3/4" 9 1/16" 5/16" - 18 x 1" 75 73
K3373CT - 1 1" 9 5/16" 3/8" - 16 x 1" 120 74
K3373CT - 1 1/4 1 1/4" 9 5/8" 3/8" - 16 x 1" 150 77
K3373CT - 1 1/2 1 1/2" 9 3/4" 3/8" - 16 x 1 1/4" 150 111
K3373CT - 2 2" 10 7/16" 3/8" - 16 x 1 1/4" 150 120
K3373CT - 2 1/2 2 1/2" 10 15/16" 3/8" - 16 x 1 1/4" 300 128
K3373CT - 3 3" 11 7/16" 3/8" - 16 x 1 1/4" 300 136
K3373CT - 3 1/2 3 1/2" 11 15/16" 3/8" - 16 x 1 1/4" 300 145
K3373CT - 4 4" 12 1/2" 1/2" - 13 x 1 3/4" 300 170
K3373CT - 5 5" 13 5/8" 1/2" - 13 x 2" 500 355
K3373CT - 6 6" 14 5/8" 1/2" - 13 x 2" 500 386
Material: Steel Standard Finish: Copper Service: Designed to support and stabilize vertical runs of copper tubing (available with plastic coasting to provide additional separa- tion between tubing and hanger) Ordering: Specify part number and finish
K3373CUPVC - Plastic Coated
Pipe Rollers + Pipe Supports Pipe rollers presented in this section are designed to accommodate for longitudinal movement due to the expansion and contraction of both insulated and non-insulated pipe. Material: Carbon Steel and Cast Iron rollers are used in the manufacturing of pipe roller supports. Stainless Steel and other materials are also available. Finishes: Finishes for pipe supports in this section are Plain Steel, Electro-Plated Zinc, Hot Dipped Galvanized, Red Primer, Plastic Coating, Stainless Steel and other special coatings are also available. Notes: Products in this section are designed and manufactured in accordance with in- dustry standards. RHK is not responsible for injuries and damage which could result from improper and negligent installation of the items.
91
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
6" 6 7/8" 7 7/8" 8 3/8" 8 7/8" 9 3/8" 9 7/8" 10 15/16"
8" 7 13/16" 8 7/8" 9 3/8" 9 7/8" 10 7/16" 10 15/16" 11 7/8"
10" 8 13/16" 9 7/8" 10 7/16" 10 15/16" 11 3/8" 11 7/8" 12 13/16"
12" 9 3/4" 10 15/16" 11 3/8" 11 7/8" 12 5/16" 12 13/16" 13 3/4"
14" 10 5/16" 11 3/8" 11 7/8" 12 5/16" 12 13/16" 13 1/4" 14 1/4"
16" 11 5/16" 12 5/16" 12 13/16" 13 1/4" 13 3/4" 14 1/4" 15 1/8"
18" 12 1/4" 13 1/4" 13 3/4" 14 3/16" 14 11/16" 15 1/8" 16 1/16"
Material: Steel with malleable iron rollers Standard Finish: Electro-Plated Service: Designed to mount on strut (metal framing) for the support of pipe with longitudinal movement. Ordering: Specify part number and finish Design Load: 1500 Lbs.
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
6" 9 9/16" 10 3/16" 10 5/8" 11" 11 3/8" 11 3/4" 12 1/2"
8" 10 1/4" 11 1/16" 11 3/8" 11 3/4" 12 3/16" 12 1/2" 13 1/4"
10" 11" 11 3/4" 12 1/8" 12 1/2" 12 13/16" 13 1/8" 13 7/8"
12" 11 11/16" 12 9/16" 12 7/8" 13 1/4" 13 9/16" 13 7/8" 14 5/8"
14" 12 1/16" 12 7/8" 13 3/16" 13 9/16" 13 7/8" 14 1/4" 14 7/8"
16" 12 3/4" 13 1/2" 13 7/8" 14 13/16" 14 1/2" 14 7/8" 15 1/2"
18" 13 1/2" 14 1/4" 14 5/8" 15" 15 5/16" 15 5/8" 16 5/16"
Reference Chart: B Dimension
Reference Chart: A Dimension
Pipe Rollers 1/2” to 8” Pipe - K218...
Material: Steel with malleable iron rollers Standard Finish: Electro-Plated Service: Designed to mount on strut (metal framing) for the support of pipe with longi- tudinal movement. Ordering: Specify part number and finish Design Load: 500 Lbs.
Notes: Channel and mounting hardware not included. Not for continuous cycling applications
93
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
1/2" 2 11/16" - - - - - -
1 1/4" 3 1/8" 4 3/16" 4 5/8" 5 1/8" - - -
1 1/2" 3 1/4" 4 3/8" 4 7/8" 5 5/16" 5 3/4" - -
2" 3 9/16" 4 11/16" 5 1/16" 5 5/8" 6 1/16" - -
2 1/2" 3 13/16" 4 7/8" 5 5/16" 6" 6 3/8" - -
3" 4 1/8" 5 1/16" 5 9/16" 6 1/8" 6 7/16" 7" -
3 1/2" 4 3/8" 5 5/16" 5 13/16" 6 1/4" 6 11/16" 7 1/4" -
4" 4 5/8" 5 9/16" 6 1/16" 6 7/16" 6 15/16" 7 3/8" -
5" 5 1/2" 6 1/6" 6 7/16" 7" 7 3/8" 7 7/8" 8 13/16"
6" 5 1/2" 6 7/16" 6 15/16" 7 3/8" 7 15/16" 8 1/2" 9 1/2"
8" 6 15/16" 7 3/8" 7 15/16" 8 7/16" 8 15/16" - -
Reference Chart: B Dimension
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
1/2" 7 1/4" - - - - - -
1" 7 1/4" 7 1/4" 7 5/8" 8 1/4" - - -
1 1/4" 7 1/4" 7 1/4" 8" 8 1/4" - - -
1 1/2" 7 1/4" 7 5/8" 8" 8 1/2" 9" - -
2" 7 1/4" 7 5/8" 8 1/2" 8 1/2" 9" - -
2 1/2" 7 1/4" 8" 8 1/2" 9" 10" - -
3" 7 1/4" 8 1/2" 9" 9" 10" 10" -
3 1/2" 7 1/4" 8 1/2" 9" 10" 10" 10" -
4" 7 5/8" 9" 9" 10" 10" 10" -
5" 8 1/2" 9" 10" 10" 11" 11" 12"
6" 9" 10" 10" 11" 11" 11" 12"
8" 10" 11" 11" 11" 12" - -
Reference Chart: A Dimension
94
K219 7 1/4" 253
K219 - 1 8" 258
K219 - 2 9" 263
K219 - 3 10" 269
K219 - 4 10 7/8" 274
K219 - 5 11 5/8" 279
Material: Steel with malleable iron rollers Standard Finish: Electro-Plated Service: Designed to mount on strut (metal framing) for the support of pipe with longitu- dinal movement. Ordering: Specify part number and finish Design Load: 750 Lbs.
Note: Not for continuous cycling applications
Pipe Rollers 3/4” to 12” Pipe - K219...
95
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
1/2" K219 - - - - - -
1" K219 K219 K219 - 1 K219 - 1 - - -
1 1/4" K219 K219 K219 - 1 K219 - 1 - - -
1 1/2" K219 K219 K219 - 1 K219 - 2 K219 - 2 - -
2" K219 K219 - 1 K219 - 1 K219 - 2 K219 - 2 - -
2 1/2" K219 K219 - 1 K219 - 2 K219 - 2 K219 - 3 - -
3" K219 K219 - 1 K219 - 2 K219 - 2 K219 - 3 K219 - 3 -
3 1/2" K219 - 1 K219 - 2 K219 - 2 K219 - 3 K219 - 3 K219 - 4 -
4" K219 - 1 K219 - 2 K219 - 2 K219 - 3 K219 - 3 K219 - 4 -
5" K219 - 1 K219 - 2 K219 - 3 K219 - 3 K219 - 4 K219 - 4 K219 - 5
6" K219 - 2 K219 - 3 K219 - 3 K219 - 4 K219 - 4 K219 - 5 K219 - 5
8" K219 - 3 K219 - 4 K219 - 4 K219 - 5 K219 - 5 - -
10" K219 - 4 K219 - 5 - - - - -
12" K219 - 5 - - - - - -
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
1/2" 2 11/16" - - - - - -
1 1/4" 3 1/8" 4 3/16" 4 5/8" 5 1/8" - - -
1 1/2" 3 1/4" 4 7/16" 4 7/8" 5 1/4" 5 3/8" - -
2" 3 9/16" 4 5/8" 5 3/16" 5 1/2" 6 1/16" - -
2 1/2" 3 3/4" 4 7/8" 5 1/4" 6" 6 3/8" - -
3" 4 1/8" 5 1/8" 5 9/16" 6 1/16" 6 7/16" 6 15/16" -
3 1/2" 4 1/8" 5 1/4" 5 13/16" 6 1/4" 6 11/16" 7 1/16" -
4" 4 9/16" 5 1/2" 6 1/16" 6 7/16" 6 15/16" 7 3/8" -
5" 5 1/16" 6 1/16" 6 7/16" 7" 7 3/8" 7 7/8" 8 15/16"
6" 5 7/16" 6 7/16" 6 15/16" 7 3/8" 7 7/8" 8 15/16" 9 9/16"
8" 6 3/8" 7 7/16" 7 15/16" 8 3/8" 9" - -
10" 7 5/16" 8 3/16" - - - - -
12" 8 1/4" - - - - - -
Adjustable Steel Yoke Pipe Roll - K3110...
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for suspending pipe where longitudinal movement and vertical adjustment is required. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with stainless steel yoke and hardware are available for most sizes (K3110NM-Pipe Size). Not for continuous cycling applications
97
Part Number Nominal Pipe Size
Rod Size "A" "B"
K3110 - 2 1/2 2 1/2" 1/2" - 13 1 7/8"
K3110 - 3 3" 1/2" - 13 2 3/16"
K3110 - 3 1/2 3 1/2" 1/2" - 13 2 1/2"
K3110 - 4 4" 5/8" - 11 2 3/4"
K3110 - 5 5" 5/8" - 11 3 3/8"
K3110 - 6 6" 3/4" - 10 3 15/16"
K3110 - 8 8" 3/4" - 10 5 1/16"
K3110 - 10 10" 7/8" - 9 6 1/4"
K3110 - 12 12" 7/8" - 9 7 3/8"
K3110 - 14 14" 1" - 8 8 1/4"
K3110 - 16 16" 1" - 8 9 1/4"
K3110 - 18 18" 1" - 8 10 3/8"
K3110 - 20 20" 1 1/4" - 7 11 1/2"
K3110 - 24 24" 1 1/2" - 6 13 13/16"
Part Number "C" "D" "E" "F" Maximum O.D.
Covering Design
Load (Lbs.) Wt./C (Lbs.)
K3110 - 2 4 3/4" 2 3/8" 1 7/16" 2 7/8" 2 5/8" 150 123
K3110 - 2 1/2 6" 3 3/16" 2" 3 1/4" 3" 225 178
K3110 - 3 6 5/8" 3 1/2" 2" 3 7/8" 3 5/8" 310 206
K3110 - 3 1/2 7 1/4" 3 3/4" 2" 4 3/8" 4 1/8" 390 267
K3110 - 4 7 7/8" 4" 2" 4 7/8" 4 11/16" 475 344
K3110 - 5 9 3/16" 4 9/16" 2" 5 15/16" 5 3/4" 685 600
K3110 - 6 10 3/8" 5 1/16" 2" 7" 6 3/4" 780 800
K3110 - 8 12 5/8" 6 1/16" 2" 9" 8 3/4" 780 1300
K3110 - 10 14 15/16" 7 3/16" 2 1/16" 11 1/8" 10 3/4" 965 1600
K3110 - 12 17 3/8" 8 3/8" 2 1/4" 13 3/8" 13" 1200 2600
K3110 - 14 19" 8 3/4" 2 1/4" 14 1/2" 14 1/4" 1200 3400
K3110 - 16 20 3/4" 9 3/4" 2" 16 3/8" 16 1/8" 1200 3900
K3110 - 18 23 11/16" 11 7/16" 2 11/16" 18 3/8" 18 1/8" 1400 4900
K3110 - 20 25 7/8" 12 1/4" 2 1/2" 20 3/8" 20 1/8" 1600 6686
K3110 - 24 31 9/16" 15" 3 1/2" 24 5/8" 24 3/8" 1800 11630
98
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
16" 15 3/16" 15 5/8" 15 7/8" 16" 16 1/4" 16 1/2" 17"
18" 15 1/2" 16" 16 3/16" 16 3/8" 16 9/16" 16 3/4" 17 3/16"
20" 16" 16 3/8" 16 9/16" 16 7/8" 16 15/16" 17 3/16" 17 1/2"
24" 16 13/16" 17 5/16" 17 1/2" 17 1/2" 17 11/16" 17 7/8" 18 1/8"
30" 17 13/16" 18 1/4" 18 3/8" 18 9/16" 18 7/8" 18 7/8" 19 1/4"
Insulation Thickness
Pipe Size 0" 1" 1 1/2" 2" 2 1/2" 3" 4"
16" 10 13/16" 11 15/16" 12 3/8" 12 15/16" 13 3/8" 13 15/16" 14 15/16"
18" 11 7/8" 12 15/16" 13 7/16" 13 15/16" 14 7/16" 14 15/16" 15 15/16"
20" 12 3/16" 13 15/16" 14 7/16" 14 7/8" 15 7/16" 15 7/8" 16 15/16"
24" 14 13/16" 15 7/8" 16 3/8" 16 7/8" 17 3/8" 17 7/8" 18 7/8"
30" 17 13/16" 18 7/8" 19 3/8" 19 7/8" 20 3/8" 20 5/16" 21 15/16"
Reference Chart: B Dimension
Material: Steel with malleable iron rollers Standard Finish: Electro-Plated Service: Designed to mount on strut (metal framing) for the sup- port of pipe with longitudinal movement Ordering: Specify part number and finish Design Load: 2000 Lbs.
Note: Not for continuous cycling applications
Reference Chart: A Dimension
Rod Size "A" "B" "C" "D" "E"
Maximum O.D.
Wt./C (Lbs.)
K3114 - 2 2" 3/8" - 16 2 5/8" 4 1/8" 1 9/16" 3/4" 3 3/4" 600 119
K3114 - 2 1/2 2 1/2" 1/2" - 13 3 1/8" 4 7/8" 1 7/8" 3/4" 3 3/4" 660 140
K3114 - 3 3" 1/2" - 13 3 3/4" 5 1/2" 2 3/16" 3/4" 4 1/2" 700 158
K3114 - 3 1/2 3 1/2" 1/2" - 13 4 1/4" 6 1/8" 2 1/2" 3/4" 5" 750 170
K3114 - 4 4" 5/8" - 11 4 3/4" 6 3/4" 2 3/4" 3/4" 5 7/8" 750 188
K3114 - 5 5" 5/8" - 11 5 13/16" 8 1/16" 3 3/8" 3/4" 7" 750 246
K3114 - 6 6" 3/4" - 10 6 7/8" 9 9/16" 3 15/16" 1 1/8" 8 1/4" 1070 504
K3114 - 8 8" 7/8" - 9 8 7/8" 11 15/16" 5 1/16" 1 1/8" 10 1/2" 1350 658
K3114 - 10 10" 7/8" - 9 11" 14 1/16" 6 1/4" 1 1/8" 12 3/4" 1730 849
K3114 - 12 12" 7/8" - 9 13" 15 13/16" 7 3/8" 1 1/8" 14 3/4" 2400 1200
K3114 - 14 14" 1" - 8 14 1/4" 17 3/4" 8 1/4" 1 1/2" 16 1/4" 3130 2289
K3114 - 16 16" 1" - 8 16 1/4" 19 3/4" 9 1/4" 1 1/2" 18" 3970 2497
K3114 - 18 18" 1" - 8 18 1/4" 21 7/8" 10 3/8" 1 1/2" 20 1/4" 4200 2899
K3114 - 20 20" 1 1/4" - 7 20 1/4" 24 1/4" 11 1/2" 1 1/2" 22 1/2" 4550 3637
K3114 - 24 24" 1 1/2" - 6 24 1/4" 28 7/8" 13 13/16" 2" 26 1/2" 6160 5664
K3114 - 30 30" 1 1/2" - 6 30 1/4" 35 1/2" 17 1/4" 2" 32 1/2" 7290 9437
Material: Steel axle with cast iron roller/malleable sockets Standard Finish: Plain or Electro- Plated Service: Designed for suspend- ing piping where longitudinal movement and vertical adjust- ment is required. When used with insulated pipe, see K3160 - K3165 Pipe Covering Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip galva- nized sockets and stainless steel hardware are available for most sizes. Not for continuous cycling applications.
100
Axle Diameter "D" "L" Wt./C (Lbs.)
K3114R - 2 2" 1 1/16" 3/4" 1 9/16" 3/8" 2 5/8" 29
K3114R - 2 1/2 2 1/2" 1 1/4" 7/8" 1 7/8" 1/2" 3 1/8" 47
K3114R - 3 3" 1 3/8" 7/8" 2 3/16" 1/2" 3 3/4" 62
K3114R - 3 1/2 3 1/2" 1 1/2" 1" 2 1/2" 1/2" 4 1/4" 71
K3114R- 4 4" 1 19/32" 1" 2 3/4" 1/2" 4 3/4" 96
K3114R - 5 5" 1 7/8" 1 1/8" 3 3/8" 5/8" 5 13/16" 131
K3114R- 6 6" 2 1/8" 1 1/4" 3 15/16" 3/4" 6 7/8" 207
K3114R - 8 8" 2 5/8" 1 1/2" 5 1/16" 7/8" 8 7/8" 323
K3114R - 10 10" 3 3/16" 1 3/4" 6 1/4" 7/8" 11" 482
K3114R - 12 12" 3 3/4" 2" 7 3/8" 1" 13" 854
K3114R - 14 14" 4 3/8" 2 1/2" 8 1/4" 1 1/8" 14 1/4" 1150
K3114R - 16 16" 4 5/8" 2 1/2" 9 1/4" 1 1/4" 16 1/4" 1200
K3114R - 18 18" 5 1/8" 2 3/4" 10 3/8" 1 1/4" 18 1/4" 1550
K3114R - 20 20" 5 5/8" 3" 11 1/2" 1 3/8" 20 1/4" 2080
K3114R - 24 24" 6 3/4" 3 5/8" 13 13/16" 1 1/2" 24 1/4" 3300
K3114R - 30 30" 8 1/2" 4 1/2" 17 1/4" 1 3/4" 30 1/4" 6200
Material: Cast Iron Standard Finish: Plain or Electro- Plated Service: Designed for supporting pipe runs with longitudinal move- ment. Use with steel rod axle Ordering: Specify part number and finish
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip gal- vanized sockets and stainless steel hardware are available for most sizes
101
Short Pattern Pipe Roller - K3117R
Part Number Nominal Pipe Size Axle Diameter "A" "D" "L" Wt./C (Lbs.)
K3117R - 2 to 3 1/2 2" to 3 1/2" 1/2" 1 7/8" 2 3/4" 70
K3117R- 4 to 6 4" to 6" 1/2" 2 1/16" 3 3/4" 114
K3117R - 8 to 10 8" to 10" 3/4" 3 1/4" 6" 329
K3117R - 12 to 14 12" to 14" 7/8" 4" 8" 600
K3117R - 16 to 20 16" to 20" 1 1/8" 4 1/2" 9" 781
K3117R - 24 24" 1 1/4" 4 7/16" 10" 842
K3117R - 30 30" 1 3/4" 5 1/2" 12 1/2" 1385
K3117R - 36 to 42 36" to 42" 2" 6" 14 7/8" 1585
Material: Cast Iron Standard Finish: Plain or Electro-Plated Service: Designed for supporting pipe runs with longitudinal movement. Use with steel rod axle Ordering: Specify part number and finish
102
K3117SL - 2 to 3 1/2
2" 1 3/4" 8 3/8" 6" 4"
2 1/2" 1 3/4" 8 3/8" 6" 4"
3" 1 3/4" 8 3/8" 6" 4"
3 1/2" 1 3/4" 8 3/8" 6" 4"
K3117SL - 4 to 6
4" 2 1/16" 9 7/8" 6" 4 1/4"
5" 2 1/16" 9 7/8" 6" 4 1/4"
6" 2 1/16" 9 7/8" 6" 4 1/4"
K3117SL - 8 to 10 8" 3 7/16" 8 5/8" 8" 5"
10" 3 7/16" 8 5/8" 8" 5"
K3117SL - 12 to 14 12" 3 7/8" 10 15/16" 8" 6"
14" 3 7/8" 10 15/16" 8" 6"
K3117SL - 16 to 20
K3117SL - 24 24" 4 3/8" 13 1/2" 10" 6 1/2"
K3117SL - 30 30" 5 1/8" 17" 10 3/4" 8"
K3117SL - 36 to 42 36" 5 3/4" 20" 12" 9"
42" 5 3/4" 20" 12" 9"
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip galvanized sockets and stainless steel hardware are available for most sizes
103
3 11/16" 1/2" 1" 3 7/16" 6 3/8" 390 508
3 15/16" 1/2" 1" 3 7/16" 6 3/8" 390 508
4 1/4" 1/2" 1" 3 7/16" 6 3/8" 390 508
4 1/2" 1/2" 1" 3 7/16" 6 3/8" 390 508
K3117SL - 4 to 6
5 9/16" 1/2" 1" 4 11/16" 7 7/8" 950 631
6 1/16" 1/2" 1" 4 11/16" 7 7/8" 950 631
K3117SL - 8 to 10 8 13/16" 5/8" 1" 7" 4" 2100 1271
9 7/8" 5/8" 1" 7" 4" 2100 1271
K3117SL - 12 to 14 11 7/16" 3/4" 1" 9 1/16" 5 3/4" 3075 1994
12 1/16" 3/4" 1" 9 1/16" 5 3/4" 3075 1994
K3117SL - 16 to 20
13 5/8" 13/16" 1" 10 1/4" 6 3/4" 4980 3423
14 11/16" 13/16" 1" 10 1/4" 6 3/4" 4980 3423
15 11/16" 13/16" 1" 10 1/4" 6 3/4" 4980 3423
K3117SL - 24 17 11/16" 13/16" 1" 11 3/8" 7 1/2" 6100 4710
K3117SL - 30 21 3/4" 1 1/16" 1" 14 1/4" 10" 7500 7132
K3117SL - 36 to 42 25 5/16" 1 3/16" 1" 17" 12" 12000 10386
28 5/16" 1 3/16" 1" 17" 12" 12000 10386
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for support of pipe with longitudinal movement. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
104
Adjustable Roller with Base Plate - K3118SL...
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip gal- vanized sockets and stainless steel hardware are available for most sizes. Not for con- tinuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for support of pipe where longitudinal movement and vertical adjustments are required. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
105
K3118SL - 2 to 3 1/2
2" 6 7/8" 6"
3" 6 7/8" 6"
K3118SL - 4 to 6
4" 8 1/8" 6"
5" 8 1/8" 6"
6" 8 1/8" 6"
10" 10 5/8" 8"
14" 13" 8"
K3118SL - 30 30" 19 1/4" 10 1/2"
Part Number "C"
(Lbs.) Wt./C (Lbs.)
4 3/4" 5 5/8" 3 7/8" 1" 1" 390 1100
5" 5 7/8" 3 7/8" 1" 1" 390 1100
5 5/16" 6 3/16" 3 7/8" 1" 1" 390 1100
5 9/16" 6 7/16" 3 7/8" 1" 1" 390 1100
K3118SL - 4 to 6
6 3/16" 7 7/16" 5 1/8" 1" 1" 950 1310
6 3/4" 8" 5 1/8" 1" 1" 950 1310
7 1/4" 8 1/2" 5 1/8" 1" 1" 950 1310
K3118SL - 8 to 10 10 1/8" 11 11/16" 7 3/8" 1" 1 1/8" 2100 2725
11 3/16" 12 3/4" 7 3/8" 1" 1 1/8" 2100 2725
K3118SL - 12 to 14 12 3/4" 14 1/8" 9 1/2" 1" 1 1/8" 3075 3612
13 3/8" 14 3/8" 9 1/2" 1" 1 1/8" 3075 3612
K3118SL - 16 to 20
15 3/8" 17 1/4" 11 1/8" 1" 1 1/4" 4980 6384
16 3/8" 18 1/4" 11 1/8" 1" 1 1/4" 4980 6384
17 3/8" 19 1/4" 11 1/8" 1" 1 1/4" 4980 6384
K3118SL - 24 19 1/4" 21 1/4" 12 1/4" 1" 1 3/8" 6100 8437
K3118SL - 30 24 7/16" 26 11/16" 15 3/4" 1" 1 5/8" 7500 12528
Adjustable Roller with Base Plate - K3118SL (cont.)
106
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip gal- vanized sockets and stainless steel hardware are available for most sizes. Not for con- tinuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for support of pipe with longitudinal movement. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Sad- dle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
Steel Roller Stand - K3119SL...
2" C4 x 5.4 4 3/4" 3 1/16"
2 1/2" C4 x 5.4 4 3/4" 3 5/16"
3" C4 x 5.4 4 3/4" 3 5/8"
3 1/2" C4 x 5.4 4 3/4" 3 7/8"
K3119SL - 4 to 6
4" C5 x 6.7 5 3/4" 4 1/8"
5" C5 x 6.7 5 3/4" 4 11/16"
6" C5 x 6.7 5 3/4" 5 3/16"
K3119SL - 8 to 10 8" C6 x 8.2 8" 7 3/16"
10" C6 x 8.2 8" 8 1/4"
K3119SL - 12 to 14 12" C8 x 11.5 10" 9 13/16"
14" C8 x 11.5 10" 10 7/16"
K3119SL - 16 to 20
K3119SL - 24 24" C8 x 11.5 12" 15 13/16"
K3119SL - 30 30" C10 x 15.3 14 1/2" 19 5/8"
Part Number "C" "D" "E" "F" Diameter
"G"
1 15/16" 2 3/4" - 1 3/4" 9/16" 390 314
2 3/16" 2 3/4" - 1 3/4" 9/16" 390 314
2 1/2" 2 3/4" - 1 3/4" 9/16" 390 314
2 3/4" 2 3/4" - 1 3/4" 9/16" 390 314
K3119SL - 4 to 6
4" 3 3/4" - 2 1/2" 11/16" 950 489
K3119SL - 8 to 10 5 3/8" 6" 3" 2 1/2" 13/16" 2100 950
6 7/16" 6" 3" 2 1/2" 13/16" 2100 950
K3119SL - 12 to 14 7 9/16" 8" 4" 3 5/8" 13/16" 3075 1740
8 3/16" 8" 4" 3 5/8" 13/16" 3075 1740
K3119SL - 16 to 20
9 3/8" 9" 4" 3 1/8" 13/16" 4980 2018
10 7/16" 9" 4" 3 1/8" 13/16" 4980 2018
11 7/16" 9" 4" 3 1/8" 13/16" 4980 2018
K3119SL - 24 13 5/16" 10" 4" 3 1/8" 13/16" 6100 2175
K3119SL - 30 16 5/8" 12 1/2" 6" 4 1/8" 13/16" 7500 3510
108
Roller Chair - K3120
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip gal- vanized sockets and stainless steel hardware are available for most sizes. Not for con- tinuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro- Plated Service: Designed for support of pipe with longitudinal movement. When used with insulated pipe, see K3160 - K3165 Pipe Covering Pro- tection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
Part Number Nominal Pipe Size "A" "B" "C"
Recommended Bolt Size (Not Included)
"D" "E"
Wt./C (Lbs.)
K3120 - 2 2" 1 1/4" 4 5/8" 1 1/2" 3/8" - 16 x 1 1/2" 1 9/16" 300 119
K3120 - 2 1/2 2 1/2" 1 1/4" 5 3/8" 1 5/8" 3/8" - 16 x 1 1/2" 1 7/8" 600 146
K3120 - 3 3" 2" 6" 1 3/4" 3/8" - 16 x 1 1/2" 2 3/16" 600 172
K3120 - 3 1/2 3 1/2" 2" 6 3/4" 2 1/16" 3/8" - 16 x 1 1/2" 2 1/2" 600 264
K3120 - 4 4" 2" 7 1/4" 2 5/16" 1/2" - 13 x 1 1/2" 2 3/4" 700 303
K3120 - 5 5" 3" 8 7/16" 2 1/2" 1/2" - 13 x 1 1/2" 3 3/8" 700 401
K3120 - 6 6" 3 1/8" 9 3/4" 2 3/4" 1/2" - 13 x 1 1/2" 3 15/16" 1000 620
K3120 - 8 8" 3 3/8" 12" 3" 5/8" - 11 x 1 1/2" 5 1/16" 1300 874
K3120 - 10 10" 5 1/4" 14 7/16" 3 5/8" 5/8" - 11 x 2" 6 1/4" 1700 1270
K3120 - 12 12" 5 1/2" 16 5/8" 4 1/8" 5/8" - 11 x 2" 7 3/8" 2300 1918
K3120 - 14 14" 6" 18 1/4" 4 5/8" 5/8" - 11 x 2" 8 1/4" 3100 2629
K3120 - 16 16" 8" 21" 5" 5/8" - 11 x 2 1/2" 9 1/4" 3900 3248
K3120 - 18 18" 9" 23" 5 1/4" 5/8" - 11 x 2 1/2" 10 3/8" 4200 4120
K3120 - 20 20" 10" 25" 5 3/4" 3/4" - 10 x 3" 11 1/2" 4500 5630
K3120 - 24 24" 12" 30" 7" 3/4" - 10 x 3" 13 3/4" 6000 7702
109
Rod Size "A" "B" "C" "D" "E" "F"
Design Load (Lbs.)
Wt./C (Lbs.)
K3122 - 2 2" 3/8" - 16 12" 4 1/8" 2 5/8" 1 9/16" 3/4" 600 194
K3122 - 2 1/2 2 1/2" 1/2" - 13 12" 4 7/8" 3 1/8" 1 7/8" 3/4" 660 284
K3122 - 3 3" 1/2" - 13 12" 5 1/2" 3 3/4" 2 3/16" 3/4" 700 302
K3122 - 3 1/2 3 1/2" 1/2" - 13 12" 6 1/8" 4 1/4" 2 1/2" 3/4" 750 314
K3122 - 4 4" 5/8" - 11 12" 6 3/4" 4 3/4" 2 3/4" 3/4" 750 438
K3122 - 5 5" 5/8" - 11 12" 8 1/16" 5 13/16" 3 3/8" 3/4" 750 495
K3122 - 6 6" 3/4" - 10 12" 9 9/16" 6 7/8" 3 15/16" 1 1/8" 1070 867
K3122 - 8 8" 7/8" - 9 12" 11 15/16" 8 7/8" 5 1/16" 1 1/8" 1350 1176
K3122 - 10 10" 7/8" - 9 12" 14 1/16" 11" 6 1/4" 1 1/8" 1730 1368
K3122 - 12 12" 7/8" - 9 12" 15 13/16" 13" 7 3/8" 1 1/8" 2400 1861
K3122 - 14 14" 1" - 8 12" 17 3/4" 14 1/4" 8 1/4" 1 1/2" 3130 3116
K3122 - 16 16" 1" - 8 18" 19 3/4" 16 1/4" 9 7/16" 1 1/2" 3970 3550
K3122 - 18 18" 1" - 8 18" 21 7/8" 18 1/4" 10 1/2" 1 1/2" 4200 4328
K3122 - 20 20" 1 1/4" - 7 18" 24 1/4" 20 1/4" 11 1/2" 1 1/2" 4550 5241
K3122 - 24 24" 1 1/2" - 6 24" 28 7/8" 24 1/4" 13 13/16" 2" 6160 7773
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip gal- vanized sockets and stainless steel hardware are available for most sizes. Not for con- tinuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for support of pipe where longi- tudinal movement and vertical adjustments are re- quired. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
110
Rod Size "A" "B" "C" "D" "E" "F"
Design Load (Lbs.)
Wt./C (Lbs.)
K3122A - 2 2" 3/8" - 16 12" 4 1/8" 2 5/8" 1 9/16" 3/4" 600 323
K3122A - 2 1/2 2 1/2" 1/2" - 13 14" 4 7/8" 3 1/8" 1 7/8" 3/4" 660 465
K3122A - 3 3" 1/2" - 13 14" 5 1/2" 3 3/4" 2 3/16" 3/4" 700 501
K3122A - 3 1/2 3 1/2" 1/2" - 13 14" 6 1/8" 4 1/4" 2 1/2" 3/4" 750 525
K3122A - 4 4" 5/8" - 11 18" 6 3/4" 4 3/4" 2 3/4" 3/4" 750 757
K3122A - 5 5" 5/8" - 11 18" 8 1/16" 5 13/16" 3 3/8" 3/4" 750 872
K3122A - 6 6" 3/4" - 10 24" 9 9/16" 6 7/8" 3 15/16" 1 1/8" 1070 1687
K3122A - 8 8" 7/8" - 9 24" 11 15/16" 8 7/8" 5 1/16" 1 1/8" 1350 2277
K3122A - 10 10" 7/8" - 9 30" 14 1/16" 11" 6 1/4" 1 1/8" 1730 2830
K3122A - 12 12" 7/8" - 9 30" 15 13/16" 13" 7 3/8" 1 1/8" 2400 3817
K3122A - 14 14" 1" - 8 36" 17 3/4" 14 1/4" 8 1/4" 1 1/2" 3130 6513
K3122A - 16 16" 1" - 8 36" 19 3/4" 16 1/4" 9 7/16" 1 1/2" 3970 6759
K3122A - 18 18" 1" - 8 42" 21 7/8" 18 1/4" 10 1/2" 1 1/2" 4200 7518
K3122A - 20 20" 1 1/4" - 7 42" 24 1/4" 20 1/4" 11 1/2" 1 1/2" 4550 11222
K3122A - 24 24" 1 1/2" - 6 48" 28 7/8" 24 1/4" 13 13/16" 2" 6160 17666
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip gal- vanized sockets and stainless steel hardware are available for most sizes. Not for con- tinuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for support of pipe where longi- tudinal movement and vertical adjustments are re- quired. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
111
Roller Support - K3124
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip galvanized sockets and stainless steel hardware are available for most sizes. Not for con- tinuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed for support of pipe where longitudinal movement and vertical adjustments are required. When used with insulated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
Part Number Nominal Pipe Size "A" "B" "C" "D" "E"
Length of Roller
Design Load (Lbs.)
K3124 - 2 to 3 1/2
2" 5/8" - 11 4 3/4" 1 3/4" 5" 1 13/16" 2 3/4" 390 233
2 1/2" 5/8" - 11 4 3/4" 2 1/8" 5" 1 13/16" 2 3/4" 390 233
3" 5/8" - 11 4 3/4" 2 3/8" 5" 1 13/16" 2 3/4" 390 233
3 1/2" 5/8" - 11 4 3/4" 2 5/8" 5" 1 13/16" 2 3/4" 390 233
K3124 - 4 to 6
4" 3/4" - 10 5 7/8" 2 3/4" 6" 2" 3 3/4" 600 368
5" 3/4" - 10 5 7/8" 3 3/8" 6" 2" 3 3/4" 600 368
6" 3/4" - 10 5 7/8" 4" 6" 2" 3 3/4" 600 368
K3124 - 8 to 10 8" 7/8" - 9 8 3/4" 5 1/4" 6" 2 11/16" 6" 800 919
10" 7/8" - 9 8 3/4" 6 3/8" 6" 2 11/16" 6" 800 919
K3124 - 12 to 14 12" 1" - 8 11 1/4" 7 1/2" 7" 3 1/4" 8" 1300 1660
14" 1" - 8 11 1/4" 8 1/8" 7" 3 1/4" 8" 1300 1660
K3124 - 16 to 20
16" 1 1/8" - 7 12 1/2" 9 3/8" 8" 3 1/2" 9" 2300 2250
18" 1 1/8" - 7 12 1/2" 10 3/8" 8" 3 1/2" 9" 2300 2250
20" 1 1/8" - 7 12 1/2" 11 3/8" 8" 3 1/2" 9" 2300 2250
112
Roller Support - K3126
Notes: If using D.I. pipe refer to page 180 for sizing. Non-metallic rollers with hot-dip galvanized sockets and stainless steel hardware are available for most sizes. Not for continuous cycling applications
Material: Steel with cast iron roller Standard Finish: Plain or Electro-Plated Service: Designed to mount on strut (metal framing) for the support of pipe with longi- tudinal movement. When used with insu- lated pipe, see K3160 - K3165 Pipe Covering Protection Saddle charts for proper sizing on pages 66-73 Ordering: Specify part number and finish
Part Number Nominal Pipe Size "A" "B" "C" "D" "E"
Design Load (Lbs.)
K3126 - 2 to 3 1/2
2" 1 7/16" 6" 3 11/16" 7 5/8" 9/16" 390 177
2 1/2" 1 7/16" 6" 3 27/64" 7 5/8" 9/16" 390 177
3" 1 7/16" 6" 3 47/64" 7 5/8" 9/16" 390 177
3 1/2" 1 7/16" 6" 3 63/64" 7 5/8" 9/16" 390 177
K3126 - 4 to 6
4" 1 7/16" 7" 4 13/64" 8 5/8" 9/16" 600 231
5" 1 7/16" 7" 4 47/64" 8 5/8" 9/16" 600 231
6" 1 7/16" 7" 5 17/64" 8 5/8" 9/16" 600 231
K3126 - 8 to 10 8" 1 13/16" 8 3/4" 7" 10 3/8" 9/16" 800 542
10" 1 13/16" 8 3/4" 8 1/16" 10 3/8" 9/16" 800 542
K3126 - 12 to 14 12" 2 7/16" 12 1/8" 9 27/32" 14 3/8" 13/16" 1300 1040
14" 2 7/16" 12 1/8" 10 15/32" 14 3/8" 13/16" 1300 1040
K3126 - 16 to 20
16" 2 5/8" 13 1/8" 11 7/8" 15 3/8" 13/16" 2300 1508
18" 2 5/8" 13 1/8" 12 7/8" 15 3/8" 13/16" 2300 1508
20" 2 5/8" 13 1/8" 13 7/8" 15 3/8" 13/16" 2300 1508
113
Spring (Lbs./in.)
Springs (Lbs.) Wt./CPR
K3264 - 1 3/8" - 16 3" 1 1/16" 30 78 100
K3264 - 5 3/4" - 10 4 5/8" 2 5/16" 707 1500 400
K3264 - 6 1" - 8 4 7/8" 3 1/4" 1600 3200 700
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed for use with K3114 as a cushion spring for a piping system where vertical movement does not exceed 1 1/4” Ordering: Specify part number, size and finish
Note: Includes 2 springs and 4 cup washers
Pipe supports presented in this section are designed to support pipe from a base structure where vertical adjustments may be necessary. Pipe guides and slides are designed to allow longitudinal movement due to thermal expansion and contraction of pipe. Protection shields and saddles are designed to prevent damage to pipe in- sulation. Materials: Carbon Steel is used in the manufacturing of pipe supports, guides, shields and saddles. Stainless Steel and other materials are also available. Finishes: Finishes for pipe supports in this section are Plain Steel, Electro-Plated Zinc, Hot Dipped Galvanized, Red Primer and other special coatings are also avail- able. Notes: All hangers in this section are sized to fit schedule 40/80 pipe unless other- wise noted. Some steel items may be specially fabricated to accommodate other pipe diameters. Products in this section are designed and manufactured in accor- dance with industry standards. RHK is not responsible for injuries and damage which could result from improper and negligent installation of the items.
Supports, Guides, Shields and Saddles
51
Base Stand - K3088
Part Number Stand Pipe Size Plate Size "A" Diameter "H" Wt./C* (Lbs.)
K3088 - 3/4 3/4" 1/4" x 6" x 6" 7/8" 3/4" 420
K3088 - 1 1" 1/4" x 6" x 6" 7/8" 3/4" 480
K3088 - 1 1/4 1 1/4" 1/4" x 6" x 6" 7/8" 3/4" 590
K3088 - 1 1/2 1 1/2" 1/4" x 6" x 6" 7/8" 3/4" 655
K3088 - 2 2" 1/4" x 6" x 6" 7/8" 3/4" 1211
K3088 - 2 1/2 2 1/2" 3/8" x 8" x 8" 1 1/4" 13/16" 2376
K3088 - 3/4 3" 3/8" x 12" x 12" 1 1/2" 13/16" 3137
K3088 - 4 4" 1/2" x 12" x 12" 1 1/2" 15/16" 4338
K3088 - 6 6" 1/2" x 18" x 18" 1 1/2" 1 1/8" 7378
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed as an unthreaded base stand for Pipe Sup- ports K3090, K3095, K3094 and K3096 Ordering: Specify part number, height and finish
Note: Match K3088 part number with dimension “D” from K3090, K3095 or K3096 charts
52
"H" Wt./C* (Lbs.)
K3088S - 3/4 3/4" 1/4" x 8" x 8" 1" 9/16" 618
K3088S - 1 1" 1/4" x 8" x 8" 1" 9/16" 708
K3088S - 1 1/4 1 1/4" 1/4" x 8" x 8" 1" 9/16" 798
K3088S - 1 1/2 1 1/2" 1/4" x 8" x 8" 1" 9/16" 858
K3088S - 2 2" 1/4" x 8" x 8" 1" 9/16" 993
K3088S - 2 1/2 2 1/2" 3/8" x 8 1/2" x 8 1/2" 1 1/4" 9/16" 1638
K3088S - 4 4" 1/2" x 13 1/2" x 13 1/2" 1 1/2" 15/16" 4202
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed as an unthreaded base stand for Pipe Supports K3090, K3095, K3094 and K3096. Designed to meet requirements of 12X anchor diameter hole spacing for seismic applications. The standard K3088-3 and K3088-6 already meet this requirement Ordering: Specify part number, height and finish
Note: Match K3088 part number with dimension “D” from K3090, K3095 or K3096 charts. Wt./C* based on a height of 18”
53
Part Number Stand Pipe
"H" "TL" Wt./C* (Lbs.)
K3088ST - 1 1" 1/4" x 8" x 8" 1" 9/16" 1 1/2" 708
K3088ST - 1 1/4 1 1/4" 1/4" x 8" x 8" 1" 9/16" 1 1/2" 798
K3088ST - 1 1/2 1 1/2" 1/4" x 8" x 8" 1" 9/16" 1 1/2" 858
K3088ST - 2 2" 1/4" x 8" x 8" 1" 9/16" 1 1/2" 993
K3088ST - 2 1/2 2 1/2" 3/8" x 8 1/2" x 8 1/2" 1 1/4" 9/16" 1 1/2" 1638
K3088ST - 4 4" 1/2" x 13 1/2" x 13 1/2" 1 1/2" 15/16" 2" 4202
Material: Steel Standard Finish: Plain or Electro-Plated Service: Designed as a threaded base stand for Pipe Supports K3089, K3091, K3092, K3093 and K3097. Designed to meet requirements of 12X anchor diameter hole spacing for seismic applications. The standard K3088T-3 and K3088T-6 already meet this requirement Ordering: Specify part number, height and finish
Note: Match K3088T part number with dimension “D” from K3089, K3092 and K3