PI-Datasheet CombiPress PFMN v7 - ikmwebshop.no · Page 2 / 4 EN/120805 Design and specifications...
4
EN/120805 Design and specifications subject to change without notice Page 1 / 4 www.baumer.com Datasheet PFMN CombiPress TM PFMN Industrial – Fully welded pressure transmitter with flush diaphragm Main features Applications n Flush diaphragm n Built in graphical display, CombiView TM DFON optional n HART ® (pending) n ATEX (pending) n Programmable by touch screen n Easy and full programmable with FlexProgrammer 9701 n Food and beverage n Pharmaceutical n Water treatment n General process industry Main characteristics (20 °C) Measuring range -1,0...400,0 bar Minimum range 35 mbar Turn down 10:1 - e.g. Range BC4 URL can be set from 2 to 20 bar Long term stability <0.1% FS / Year Accuracy (Linearity, hysteresis and repeatabillity) <±0.1% FS / <±0,25% FS Standard process temperature -40 … 125 °C (<150 °C <6 0 min.) Max. process temperature 200 °C (with cooling neck) Technical specification Measuring principle Piezoresistive silicon sensor Measuring ranges -1 … 0 bar up to 0 … 400 bar, Min. range 0…0,05 bar, programmable Type of pressure Relative / Absolute Turn down 10:1 Accuracy (20 °C ambient) (Linearity, Hysteresis, Repeatability) 0.1% FS @ -20…85 °C, medium temp 0.25% FS @ -40…85 °C, medium temp Zero thermal drift ≤ ± 0.05% FS/10 K Span thermal drift ≤ ± 0.05% FS/10 K Annual stability, IEC 770 6.3.2 0.1% FS / Year Response time (10 … 90%) ≤ 0,3 sec. Sample time ≤ 0,3 sec. Start up time <10 sec. Process connections See page 3 Environment Temperature Storage -40…+85 °C Medium (without cooling neck) -40…+125 °C Short term (SIP) 150 °C for 60 min. Medium (with cooling neck) -40…+200 °C Ambient -40…+85 °C Protection rating, IEC 529 IP67 / IP69K, depending on electrical connection Humidity, IEC 68-2-38 98%, condensing Vibration IEC60068-2-6 1.5 mm (10 - 50 Hz), 20 g (55 Hz - 2 KHz) Electrical specification Output signal 4…20 mA, 20…4 mA, 4…20 mA HART ® (pending) Power Supply 10…35 VDC Load impedance RQ = (Usupply-10 V) / 20 mA Insulation resistance >100 MΩ at 500 V Sensor failure Configurable, 3,6…4 or 20…23 mA Electrical connections SS M12 connector or SS M16 gland see page 2
Transcript of PI-Datasheet CombiPress PFMN v7 - ikmwebshop.no · Page 2 / 4 EN/120805 Design and specifications...
EN
/120
805
D
esig
n an
d sp
ecifi
catio
ns s
ubje
ct to
cha
nge
with
out n
otic
e
Page 1 / 4www.baumer.com Datasheet PFMN
CombiPressTM PFMNIndustrial – Fully welded pressure transmitter with fl ush diaphragm
Main features
Applications
n Flush diaphragm n Built in graphical display, CombiViewTM DFON optional n HART® (pending) n ATEX (pending)
n Programmable by touch screen n Easy and full programmable with FlexProgrammer 9701
n Food and beverage n Pharmaceutical n Water treatment n General process industry
Main characteristics (20 °C)Measuring range -1,0...400,0 barMinimum range 35 mbarTurn down 10:1 - e.g. Range BC4 URL can be
set from 2 to 20 barLong term stability <0.1% FS / YearAccuracy (Linearity, hysteresis and repeatabillity)
<±0.1% FS / <±0,25% FS
Standard process temperature -40 … 125 °C (<150 °C <6 0 min.)Max. process temperature 200 °C (with cooling neck)Technical specifi cation
Measuring principle Piezoresistive silicon sensorMeasuring ranges -1 … 0 bar up to 0 … 400 bar,Min. range 0…0,05 bar, programmableType of pressure Relative / AbsoluteTurn down 10:1Accuracy (20 °C ambient) (Linearity, Hysteresis, Repeatability)
0.1% FS @ -20…85 °C, medium temp0.25% FS @ -40…85 °C, medium temp
Zero thermal drift ≤ ± 0.05% FS/10 KSpan thermal drift ≤ ± 0.05% FS/10 KAnnual stability, IEC 770 6.3.2 0.1% FS / YearResponse time (10 … 90%) ≤ 0,3 sec.Sample time ≤ 0,3 sec.Start up time <10 sec.Process connections See page 3
EnvironmentTemperature Storage -40…+85 °C Medium (without cooling neck) -40…+125 °C Short term (SIP) 150 °C for 60 min. Medium (with cooling neck) -40…+200 °C Ambient -40…+85 °CProtection rating, IEC 529 IP67 / IP69K, depending on
electrical connectionHumidity, IEC 68-2-38 98%, condensingVibration IEC60068-2-6 1.5 mm (10 - 50 Hz), 20 g
(55 Hz - 2 KHz)Electrical specifi cation
Output signal 4…20 mA, 20…4 mA,4…20 mA HART® (pending)
Power Supply 10…35 VDCLoad impedance RQ = (Usupply-10 V) / 20 mAInsulation resistance >100 MΩ at 500 VSensor failure Confi gurable, 3,6…4 or 20…23 mAElectrical connections SS M12 connector or SS M16
gland see page 2
Page 2 / 4www.baumer.com
EN
/120
805
D
esig
n an
d sp
ecifi
catio
ns s
ubje
ct to
cha
nge
with
out n
otic
e
CombiPressTM PFMNIndustrial – Fully welded pressure transmitter with flush diaphragm
Datasheet PFMN
Display specificationsType Graphically LCDFront glass PolycarbonateDisplay modes 8 modes, programmable, e.g.
value, bar graph, analogue, tank illustration
Background White, green, red - programmableMeasuring range -9999...99999Digit height Max. 22 mmAccuracy 0,1% @ ambient -10…70 °CVoltage drop White, green, red - programmableOutput 2 configurable relay output, 60 Vp,
75 mAProgramming Touch screen or FlexProgrammer
9701
Measuring ranges and over pressure safetyPressure in bar
Pressure range 0,0…0,345 -1,0…1,0 -1,0…5.0 -1,0…20,0 -1,0…34,0 -1,0…68,0 -1,0…400,0Over pressure 1 3 15 60 70 135 690Burst pressure 2 6 30 120 140 270 1350
MaterialProcess connection SS 1.4404, AISI 316L
(Hastelloy-C)Housing SS 1.4301, AISI 304Diaphragm SS 1.4435, AISI 316L
(Hastelloy-C)Sealing NBR, EPDM or FKM (Viton®)Approvals
Apply to EMC directive 2004/108/CEin accordance withEN61000-6-2, EN 61000-6-3Pressure directive 97/23/CE
ATEXEx ia IIC T4/T5, ATEX II 1G (Preliminary) (Pending)
Disposal of product and packing.According to national laws or by returning to Baumer.
Further information can be found in separate data sheet for DFON, D21.09.
Electrical connections
www.baumer.com Design and specifications subject to change without notice
Data sheet xxxx Page 4
Electrical connections
Dimensions (mm)
Text text text text
Process connections dimensions (mm)
Standard High temp. LCN: Code 41 � Code 71 77 mm Code 44 � Code 74 89 mm
Cable gland Transmitter - - 24VDC / - 4...20mA + +24VDC / +4...20mA Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
Display 1 N.C. 2 N.C. 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
G½A DIN 2852 G½A Conical Cooling neck Code 41 Code 44 high temperature
M12, 5-wire M12, 8-wire
1 N.C.2 - supply, 4...20 mA 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 7 + supply, 4...20 mA 8 N.C.
1 - supply, 4...20 mA 2 Common for relays 3 + supply, 4...20 mA 4 Relay 1 5 Relay 2
Front view Bottom connection Rear connection
Baumer A/SBaumer A/S
1 + supply, 4...20 mA2 Common for relays3 - supply, 4...20 mA4 Relay 15 Relay 2
1 N.C.2 + supply, 4...20 mA3 Relay 14 Relay 15 Relay 26 Relay 27 - supply, 4...20 mA8 N.C.
Page 3 / 4www.baumer.com
EN
/120
805
D
esig
n an
d sp
ecifi
catio
ns s
ubje
ct to
cha
nge
with
out n
otic
e
CombiPressTM PFMNIndustrial – Fully welded pressure transmitter with flush diaphragm
Datasheet PFMN
www.baumer.com Design and specifications subject to change without notice
Data sheet xxxx Page 4
Electrical connections
Dimensions (mm)
Text text text text
Process connections dimensions (mm)
Standard High temp. LCN: Code 41 � Code 71 77 mm Code 44 � Code 74 89 mm
Cable gland Transmitter - - 24VDC / - 4...20mA + +24VDC / +4...20mA Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
Display 1 N.C. 2 N.C. 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
G½A DIN 2852 G½A Conical Cooling neck Code 41 Code 44 high temperature
M12, 5-wire M12, 8-wire
1 N.C.2 - supply, 4...20 mA 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 7 + supply, 4...20 mA 8 N.C.
1 - supply, 4...20 mA 2 Common for relays 3 + supply, 4...20 mA 4 Relay 1 5 Relay 2
Front view Bottom connection Rear connection
Dimensions (mm)
Process connections dimensions (mm)
www.baumer.com Design and specifications subject to change without notice
Data sheet xxxx Page 4
Electrical connections
Dimensions (mm)
Text text text text
Process connections dimensions (mm)
Standard High temp. LCN: Code 41 � Code 71 77 mm Code 44 � Code 74 89 mm
Cable gland Transmitter - - 24VDC / - 4...20mA + +24VDC / +4...20mA Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
Display 1 N.C. 2 N.C. 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
G½A DIN 2852 G½A Conical Cooling neck Code 41 Code 44 high temperature
M12, 5-wire M12, 8-wire
1 N.C.2 - supply, 4...20 mA 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 7 + supply, 4...20 mA 8 N.C.
1 - supply, 4...20 mA 2 Common for relays 3 + supply, 4...20 mA 4 Relay 1 5 Relay 2
Front view Bottom connection Rear connection
91
66
95,5
82ø 91
www.baumer.com Design and specifications subject to change without notice
Data sheet xxxx Page 4
Electrical connections
Dimensions (mm)
Text text text text
Process connections dimensions (mm)
Standard High temp. LCN: Code 41 � Code 71 77 mm Code 44 � Code 74 89 mm
Cable gland Transmitter - - 24VDC / - 4...20mA + +24VDC / +4...20mA Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
Display 1 N.C. 2 N.C. 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 Com 1 Red clip (FlexProgrammer) Com 2 Black clip (FlexProgrammer)
G½A DIN 2852 G½A Conical Cooling neck Code 41 Code 44 high temperature
M12, 5-wire M12, 8-wire
1 N.C.2 - supply, 4...20 mA 3 Relay 1 4 Relay 1 5 Relay 2 6 Relay 2 7 + supply, 4...20 mA 8 N.C.
1 - supply, 4...20 mA 2 Common for relays 3 + supply, 4...20 mA 4 Relay 1 5 Relay 2
Front view Bottom connection Rear connection
Page 4 / 4www.baumer.com
EN
/120
805
D
esig
n an
d sp
ecifi
catio
ns s
ubje
ct to
cha
nge
with
out n
otic
e
CombiPressTM PFMNIndustrial – Fully welded pressure transmitter with flush diaphragm
Datasheet PFMN
Ordering details
–ModelCombiPressTM PFMN
HousingStainless steel 1.4301 / AISI304 Bottom connection 5Stainless steel 1.4301 / AISI304 Rear connection 6
Accuracy±0.25% 4±0.10% (not range 0,345 mbar) 5
Pressure range and unitMin. 0.0 / Max 0.345 Bar (not vacuum or absolute) BC1Min. -1.0 / Max 1.0 Bar BC2Min. -1.0 / Max 5.0 Bar BC3Min. -1.0 / Max 20.0 Bar BC4Min. -1.0 / Max 34.0 Bar BC5Min. -1.0 / Max 68.0 Bar BC6Min. -1.0 / Max 400.0 Bar BC7
Kind of pressureRelative RAbsolute A
Output signal4...20 mA A14…20 mA + HART® C1
Output ConnectionM12, 5 pins 15M12, 8 pins 18Cable gland, M16 55
Material fo el. connectionPlastic 1AISI 304 3
Process connectionG 1/2" A flush DIN3852 41G 1" flush. Cone. 44G 1/2" A flush DIN3852 with cooling neck 71G 1" flush cone with cooling neck 74
Wetted parts materialStainless steel 1.4404 / AISI 316L 2Hastelloy C H
SealNBR Standard 1EPDM 2FKM (Viton®) 3
Oil fillingSilicon oil -40…200 °C 1FDA approved white oil -10…200 °C Standard 2
DisplayWithout display 1With display No relays activated 2With display With activated relays 4
ATEXWithout 0
ApprovalsWithout 0
ConfigurationNo configuration 0Configuration of Range 1Configuration of Range + Display 2Configuration of Range + Display incl. 2 x relays 3
If the product wanted is not available from above list please inquire.
