Nanotechnology for Next Generation Solar Cells Group 1: Amy Cornforth, Tony Grupp, Ana D’Almeida...
-
Upload
katy-hinde -
Category
Documents
-
view
215 -
download
1
Transcript of Nanotechnology for Next Generation Solar Cells Group 1: Amy Cornforth, Tony Grupp, Ana D’Almeida...
Nanotechnology for Next Generation Solar Cells
Group 1:
Amy Cornforth, Tony Grupp, Ana D’Almeida
February 5, 2010
Presentation Overview
1. Solar cell introduction
2. Quantum dot solar cells
3. Dye-sensitized solar cells (DSSC)
4. Hybrid organic solar cells
Solar Cells• Units that have the ability of converting sunlight
into electricity• Made of semiconducting material• Can be used for varied purposes, e.g. to power
watches, to light houses, and to provide power to the electrical grids
Image found at: http://en.wikipedia.org/wiki/File:Borealis3windmills.jpg How Solar Cells Work. http://solarpanelworld.com/how-solar-cells-work.php
Solar Cells
• How do they work?– Light is absorbed by semiconductor– Energy of the electrons increases– Electrons move in the material– Charge carriers have to be present
• Limitations– Band gap of the semi-conducting material – Maximum efficiency of a solar cell (single
material) is about 30 %
How Solar Cells Work. http://solarpanelworld.com/how-solar-cells-work.php
Solar Cell Development
Three Generations of solar cell technology:1. Single-crystal silicon based photovoltaic devices
• Good efficiency• High Cost
Higher than traditionally-produced electricity
2. CuInGaSe2 (CIGS) polycrystalline semiconductor thin films• Low Cost• Less Efficiency
3. Nanotechnology-enhanced solar cells• Low Cost• Medium Efficiency
Quantum Dots
Advantages• Adjustable band-gap• Moldable • Facilitate collection and transport of carriers • Increase efficiency of solar cells
• by extending the band gap of solar cells• by generating more charges from a single photon
Quantum Dots and Ultra-Efficient Solar Cells? http://www.i-sis.org.uk/QDAUESC.php
Quantum Dots
• Quantum dot sensitized solar cells (QDSCs) are third-generation photovoltaic devices
• Semiconductor sensitizers– Very tunable– Theoretically increase
efficiency of solar cells up to 44%
Published in:Ivn Mora-Ser, Sixto Gimnez, Francisco Fabregat-Santiago, Roberto Gmez, Qing Shen, Taro Toyoda, Juan Bisquert;Recombination in Quantum Dot Sensitized Solar Cells.Accounts of Chemical Research 2009 42 (11), DOI: 10.1021/ar900134d , Copyright © 2009 ASC
Image found at:: http://nanopatentsandinnovations.blogspot.com/2009_11_01_archive.html
Quantum Dots• How to improve the performance and stability of
QDSCs?
• Deposit CdSe quantum dots on nanostructured mesoporous TiO2 electrodes
Image found at: www.mrl.ucsb.edu/.../RISE/interns01/AlysonW.html
Published in:Ivn Mora-Ser, Sixto Gimnez, Francisco Fabregat-Santiago, Roberto Gmez, Qing Shen, Taro Toyoda, Juan Bisquert;Recombination in Quantum Dot Sensitized Solar Cells.Accounts of Chemical Research 2009 42 (11), DOI: 10.1021/ar900134d , Copyright © 2009 ASC
Dye-Sensitized Solar Cells
Published in: Hiroshi Imahori and Tomokazu Umeyama; J. Phys. Chem. C 2009, 113 (21). DOI: 10.1021/jp9007448Copyright © 2009 American Chemical Society
DSSC Basics
• Thin-film solar cell– Think sandwich
• Electrons for movement are provided by the photosensitive dye– Electrons provided by silicon base in other cells– Compare with previously demonstrated cell
• Nanomaterials used to create 3-D structure for dye– Greater number of dye molecules due to greater
internal surface area
Image found at http://en.wikipedia.org/wiki/Dye-sensitized_solar_cell, cited Secondary Article 2
Basic DSSC Layers:
1. Glass coated with fluorine-doped tin oxide
2. Titanium dioxide layer (n-type semiconductor)
3. Ruthenium dye4. Electrolyte
solution5. Glass coated with
platinum
c) Demonstration of DSSC cell
d) TiO Nanostructure
e) Electron energy levels
1. Electron injection from dye to conduction band
2. Electron recombination with dye cation
3. Dye regeneration from electrolyte
4. Electron recombination with electrolyte
5. Electron trapping in nanostructure Published in: Qifeng Zhang, Christopher S. Dandeneau, Xiaoyuan Zhou, and Guozhong Cao; Advanced Materials. 2009, 21, 4087–4108. DOI: 10.1002/adma.200803827 Copyright © 2009 Wiley-VCH
DSSC Nanostructure
• Porous interconnected structure• Surface area increased 1000 times when
compared to bulk materials• Crystals cause light-scattering and
increase efficiency, but also cause electron trapping
• Thickness, shape, material all effect cell efficiency
Published in: Qifeng Zhang, Christopher S. Dandeneau, Xiaoyuan Zhou, and Guozhong Cao; Advanced Materials. 2009, 21, 4087–4108. DOI: 10.1002/adma.200803827 Copyright © 2009 Wiley-VCH
ZnO NanostructuresPublished in: Qifeng Zhang, Christopher S. Dandeneau, Xiaoyuan Zhou, and Guozhong Cao; Advanced Materials. 2009, 21, 4087–4108. DOI: 10.1002/adma.200803827 Copyright © 2009 Wiley-VCH
a) Diagram of cell with nanowires
b) Image of nanowires
c) Comparison of cell performance for various shapes and types of nanostructures
Published in: Qifeng Zhang, Christopher S. Dandeneau, Xiaoyuan Zhou, and Guozhong Cao; Advanced Materials. 2009, 21, 4087–4108. DOI: 10.1002/adma.200803827 Copyright © 2009 Wiley-VCH
DSSC Modifications
• Replace organic electrolyte solution– Volatile, undergoes expansion and contraction– Gel electrolyte– Polymer electrolyte– Solid organic conductor– Inorganic semiconductor
• Replace ruthenium dye– Difficult to produce, environmentally dangerous– Organic dyes– Inorganic quantum dots
• Replace TiO2 layer– SnO2
– ZnOPublished in: L. M. Peter; J. Phys. Chem. C 2007, 111 (18). DOI: 10.1021/jp069058bCopyright © 2007 American Chemical Society
DSSC Development History
• 1991– Nature paper by O'Regan and Grätzel– First suggestion of workable DSSC
• 2006– Use of nanowires and nanoparticles– Demonstrated good chemical and thermal
resistance
• 2007, 2008– Use of low-cost organic dyes and solvent-free
electrolyte solution investigated
Dye-Sensitized Solar Cell. Wikipedia. http://en.wikipedia.org/wiki/Dye-sensitized_solar_cell
DSSC Efficiency
• High chance of proton absorption and high chance of electron movement– 90% Quantum Efficiency for green light
• Quantum Efficiency-chance that one photon will convert one electron
• Overall efficiency is 11% or less, depending on materials of construction
Dye-Sensitized Solar Cell. Wikipedia. http://en.wikipedia.org/wiki/Dye-sensitized_solar_cell
DSSC Summary
• Medium efficiency
• Low cost
• Problems to be addressed:– Liquid electrolyte (freezing, expanding,
volatility)– Poor performance in red region of light
Dye-Sensitized Solar Cell. Wikipedia. http://en.wikipedia.org/wiki/Dye-sensitized_solar_cell
Organic Hybrid Solar Cells
• PT (polythiophene) and other oligomers have better morphology and optoelectronic properties for increased efficiency
• Based on P3HT (poly-3(hexylthiophene)) derivatives
Image at http://www.iae.kyoto-u.ac.jp/molecule/nedo-mirai.jpg
What is an Oligothiophene?
• Definition: Molecules in which two or more thiophene rings are linked together
• Gives rise to many optical and electrical properties such as fluorescence, semiconductance, and light emission
Both images found at http://www.isof.cnr.it/ppage/capob/thiof.html
Scheme 1: Mechanism of Excited State Deactivation of Higher Generation Thiophene Dendrimers
Published in: Guda Ramakrishna; Ajit Bhaskar; Peter Bauerle; Theodore Goodson; J. Phys. Chem. A 2008, 112, 2018-2026. DOI: 10.1021/jp076048h Copyright © 2008 American Chemical Society
Why are oligothiophenes important?
• Highly versatile chemistry• Very simple to synthesize basic molecules• Used in organic light emitting diodes (LEDs)• Field effect transistors
– Uses an electric current to control the conductivity of charge
• Organic photovoltaic and light harvesting devices (solar cells)
P3HT – poly(3-hexylthiophene)
• One of the major layers in an organic solar cell to increase efficiency
• In some lower quality solar cells the addition of P3HT increased efficiency from 0.05% up to 0.29%
• The best organic solar cells can reach up to 4-5% efficiency
• Current commercial solar cells use highly purified silicon and reach 22% efficiency
PT and P3HT
• A) PT• B) P3HT
• Both are derived from the basic oligothiophene structure
• P3HT has a hexane chain added to the C5 position of each thiophene ring
Image found at http://www.condensed-matter.uni-tuebingen.de/resources/pictures/molecules/P3HT.gif
Figure 1 Molecular structures of the investigated 3D oligothiophene dendrimers.
Published in: Guda Ramakrishna; Ajit Bhaskar; Peter Bauerle; Theodore Goodson; J. Phys. Chem. A 2008, 112, 2018-2026. DOI: 10.1021/jp076048h Copyright © 2008 American Chemical Society
Atomic structure in the case of (a) P3HT with 2510 atoms and (b) P3HT with 10 040 atoms. Hydrogen atoms have been removed for clarity. Main chains are shown in black and side chains in gray.
Published in: Nenad Vukmirovic; Lin-Wang Wang; J. Phys. Chem. B 2009, 113, 409-415. DOI: 10.1021/jp808360y Copyright © 2008 American Chemical Society
What is needed?
• Organic solar cells have two main objectives:– 1. They must have efficient excitation
delocalization and energy transfer to best mimic natural systems (such as plants)
– 2. Must be able to convert solar energy and have large electron mobility properties (P3HT helps considerably with this)
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Zinc and Titanium Oxide Nanorods
• Simple solar cell design where zinc oxide nanorods are grown and a layer of titanium oxide is layered on those rods
• P3HT is layered overtop the rods as the hole-conducting polymer
• Significantly increases the voltage difference across the cell, and can be exposed to atmospheric air to increase efficiency
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
How can we improve?
• One field of current research is to form a mesh of carbon nanotubes with a P3HT light absorbing film
• The following slides show one experiment from Stanford University with the current and voltage across a solar cell
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Published in: McGehee, M.; Mayer, A.; Parmer, J.; Rowell, M.; Topinka, M.; Burkhardt, G. Improving Organic Solar Cells C 2007 Stanford University
Results
• Efficiency over the system was nearly triple from previous experiments, going up to 3% using a 95% transparent film over the top of the cell
• An increase in the carbon nanotube density of 20% resulted in a increase of conductivity by 15-fold
• Increasing the thickness of the P3HT layer aided electron transfer
• Research should be done to improve the transparency of the top film layer to be above 95%
Sources
Main Article:1. Nanotechnology for Next Generation Solar Cells. Prashant V. Kamat and George
C. Schatz. J. Phys. Chem. C, 2009. http://pubs.acs.org/doi/full/10.1021/jp905378n?cookieSet=1#citing
Secondary Articles:1. Hiroshi Imahori and Tomokazu Umeyama. Donor−Acceptor Nanoarchitecture on
Semiconducting Electrodes for Solar Energy Conversion. J. Phys. Chem. C 2009. http://pubs.acs.org/doi/abs/10.1021/jp9007448
2. Wikipedia. Dye-sensitized solar cell. http://en.wikipedia.org/wiki/Dye-sensitized_solar_cell
3. Qifeng Zhang, Christopher S. Dandeneau, Xiaoyuan Zhou, Guozhong Cao. ZnO Nanostructures for Dye-Sensitized Solar Cells. Advanced Materials. C 2009. http://www3.interscience.wiley.com/cgi-bin/fulltext/122498586/PDFSTART
4. Peter, L. M. Characterization and modeling of dye-sensitized solar cells. J. Phys. Chem. C 2007. http://dx.doi.org/10.1021/jp069058b
5. Prashant V. Kamat. Meeting the Clean Energy Demand: Nanostructure Architectures for Solar Energy Conversion. J. Phys. Chem. C 2007. http://pubs.acs.org/doi/full/10.1021/jp066952u
6. Yasuhiro Tachibana, Kazuya Umekita, Yasuhide Otsuka, Susumu Kuwabata. Charge Recombination Kinetics at an in Situ Chemical Bath-Deposited CdS/Nanocrystalline TiO2 Interface. J. Phys. Chem. C, 2009, 113 (16), pp 6852–6858 http://pubs.acs.org/doi/full/10.1021/jp809042z
Group S1 Rebuttal
• Most of the comments were positive, which were appreciated.
• Of the negative comments, while we agree with most, the ones we don’t agree with was our shortened introduction. We believe that our topic was a continuation of the solar cell discussion Dr. Seminario gave on the first day of class, and therefore a long introduction was not needed.
Group S1
Group S2: Review of Solar Technology
Chris HeflinRachael HoukMichael Jones
Positives
• Group S1 was the first to present, and therefore had a harder time knowing what to expect with the presentation. However, they presented a professional, well organized presentation.
• Each presenter was knowledgeable on their respective areas of the topic, spoke clearly and fluently.
Negatives
• The group should make use of the microphones and vocal projection in order to be well heard. Everything was very quiet.
• Many of the slides contained only words and no pictures, making the presentation less interesting.
• Some of the material was a bit more technical than most were prepared for. A bit more introduction would be beneficial.
Bradford LambMichael KoettingJames Kancewick
Week 1 Additional SlidesSeminar
Group S3
We felt S1 should have had more detailed background slides towards solar technology.
The information that they presented was somewhat lost on the audience because it was too detailed without having a solid background.
Thus, we attached two additional slides that improve background knowledge.
Group S3
Solar powered electrical generation relies on heat engines and photovoltaics
limited only by human ingenuity most common way is to use solar
panels Passive solar or active solar
Group S3
used to make saline or brackish water potable
Solar energy may be used in a water stabilization pond to treat waste water without chemicals or electricity
Group S3
Group S4Review of Solar Cell Technology
Joshua MorenoScott Marwil
Danielle Miller
Group S4
Things Done Well
• The group created a very nice power point that was full of good visuals and rich information
• The group spoke very clearly and made minimal use of words like “um.”
• The group presented the material in a fun and interesting way.
Group S4
Things That Need Improvement
• The group needs to try to not fit so much information on every slide. The slides got a bit wordy in some areas.
• The group needs to develop the introduction a little bit more. We felt like it was too short and did a poor job of leading into the material.
Group S4
Group 5Pradip Rijal
Jason SavatskyTrevor SeidelLaura Young
Group S5
Group S5Review of Solar Cell Technology
Presentation Review
• The group overall did a very good job.• They talked about the use of DSSC and
Quantum Dots being used in Solar Cells but they did not tell us what they were.
• Organization was satisfactory.• Could work on speaking louder.
Group S5
Critiqued by S6
Michael Trevathan
Daniel Arnold
Michael Tran
John Baumhardt
Group S6
Summary Discussed new solar cell efficiencies resulting
from nanotechnology Needed to discuss the feasibility of this
technology becoming a substantial source of energy
Needed more analysis on cost – at least some estimated ranges based on the material
They all dressed nicely and spoke clearly They were knowledgeable and directed their
attention toward the audience Overall – great presentation!
Group S6