MI 7.4-18 Quality Requirements Rev Q - gkn.com · Master document file contained in GKN Document...

MI 7.4-18 Quality Requirements, Rev Q

Page 1 of 43

Master document file contained in GKN Document Management System. Uncontrolled when printed Verify version prior to use. Remove obsolete uncontrolled documents from points of use immediately.

1. Purpose

1.1 The purpose of this document is to define the methods for creating and modifying GKN Aerospace St. Louis Quality Requirements.

2. Definitions and Acronyms

2.1 Quality Requirement (QR) - a defined special purchase order condition relative to quality assurance needs for procured direct materials.

2.2 Integrated Product Team (IPT) - A cross-functional team tasked with reviewing and deploying customer requirements.

2.3 SCM - Supply Chain Management

3. Responsibilities

3.1 Supply Chain Management Quality Engineering & Quality IPT Representatives will:

3.1.1 Identify the need for new or revised Quality Requirements (QRs) as a result of their participation on IPT Teams reviewing customer contract requirements in accordance with MI 7.1-4.

3.2 Supply Chain Quality Engineering will:

3.2.1 Approve and post updates to the Quality Requirements on the GKN Virtual Community web-site for supplier access as changes occur and audit the requirements flowdown process through IPT activity.

3.2.2 Post a current copy of the GKN Aerospace Design Authority Specification Matrix each month on the GKN Virtual Community website: http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx

4. Flowchart

None

5. Methods / Instructions

5.1 Identification of New/Modified QRs

http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspxhttp://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx


Page 2 of 43


5.1.1 Quality and Supply Chain Quality representatives will identify the need for new or revised Quality Requirements (QRs) as a result of their participation on IPTs per MI 7.1-4 - Configuration Management. These same individuals will develop the necessary text regarding new or modified QRs.

5.1.2 The GKN QR numbering format is as follows: QR# = QCXXXX, where XXXX = Unique 4 digit number

5.2 Review and Approval of New/Modified QRs

5.2.1 Supplier Quality Engineering will update the attached list of QRs (Appendix A) and submit it along with this work instruction for approval.

5.2.2 Supplier Quality Engineer will review and revise MI 7.4-24 (a) Receiving Verification Check List Reference as needed to ensure that receiving personnel are instructed to verify the inclusion of the correct documentation.

5.3 QR Flowdown

5.3.1 Supplier Quality Engineering will monitor select purchase orders to confirm the proper flowdown of Quality Requirements from IPT reviews.

5.3.2 Once approved, the latest revision of the QRs will be posted on the GKN Supplier Portal: http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx. Periodic electronic and/or hardcopy mailings may be used to inform suppliers of updates to Quality Requirements; however, the GKN Supplier Portal will be the primary form of communication of the Quality Requirements to the supplier and it will be the suppliers responsibility to work to the latest revision of QRs in this website.

5.4 Design Authority Specification Flowdown

5.4.1 Supplier Quality Engineering will retrieve a list of the current revisions of all customer specifications in GKNs QMIS Document Control at the beginning of each month.

5.4.2 Supplier Quality Engineering will use this list to revise the GKN Aerospace Design Authority Specification Matrix and upload to the GKN Supplier Portal: http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx.

http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx.http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx.http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspxhttp://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx


Page 3 of 43


6. Reference Documents

Document Number Document Title

SP 7.4 Purchasing

MI 7.1-4 Configuration Management

7. Records

Required Record Custodian

GKN Aerospace Design Authority Specification Matrix

GKN Supplier Quality Engineering

8. Form(s)

Form Title

MI 7.4-18 (a) Pre-Shipment Kit Quality Compliance Checklist

MI 7.4-24 (b) Receiving Verification Checklist Reference

9. Appendices

Appendix A Purchase Order Quality Requirements (QRs)

10. Approvals

Manager, Supply Chain


Page 4 of 43


11. Revision History

Rev Revision Description Requestor Release Date

A Initial Release N. Knittel 06 October 2011

B Added QC 7091 GIDEP Program S. Lauer 01 December 2011

C Updated QR# QC2040 Certificates of

Conformance

M. Brimer 19 December 2011

D Revised QR# QC2098 First Article

Inspection

R. Webelhuth 18 May 2012

E Revised QR# QC6000 HTF7000-Specific

Quality Requirements K. Crawford 28 November 2012

F Added QR# QC1305 Material Substitution

Prohibition - Boeing H900 Section 26 /

Added Bell QRs

R. Webelhuth / M.

Brimer 10 May 2013

G Added Boeing & Government owned Tool

Requirements

C. Dabbelt 16 January 2014

H Updated GKN Supplier Website R. Webelhuth 28 February 2014

I Updated QC5102 to reference proper heat

treat specification

N. Knittel 25 March 2015

J Added QC5109 N. Knittel 06 October 2015

K Added QC2041 R. Webelhuth 10 November 2015

L Added QC2042 R. Webelhuth 09 May 2016

M Added QC2060, made several obsolete N. Knittel 01 June 2016


Page 5 of 43


Rev Revision Description Requestor Release Date

N Added QRs 8100 and 8110 N. Knittel 05 October 2016

O Revision level O not used -- --

P Added QR 1400 and 2200 D. Arbogast 02 August 2017

Q Updates to QR 7000, 7030, 7060, 7070 and

7080

G. Suomela Reference QMIS

MI 7.4-18 Quality Requirements, Rev P

Page 6 of 43

Appendix A

GKN Aerospace - St. Louis

Purchase Order Quality

Requirements (QRs) [MI 7.4-18 Rev P]

This document contains the quality requirements that are applicable when invoked by GKN Aerospace St. Louis Purchase Orders. Use of this document is

required for Contract Review and Quality Planning Activities.

QR # QC1000 Kitting Quality Requirement Compliance Checklist New - 04/18/03 Supplier is required to review all purchase order requirements (including applicable GKN Quality Requirements) for each constituent part/material of the supplied kit and then confirm compliance of the total kit to these requirements via completion of QR FORM QC1000 for each individual kit supplied prior to shipment to GKN. A copy of this completed form is to be included with the certificate of conformance transmitted with each shipment to GKN-STL. QR # QC 1100 Work related to Lockheed Martin Aeronautics Company Purchase Order New 2/25/05 Revised 8/25/09 Work to be accomplished in performance of this purchase order is directly related to a Lockheed Martin Aeronautics Company purchase order and must be accomplished in accordance with process specification on this purchase order and Lockheed Martin Aeronautics Company Appendices QJ, QX, and Quality Clause Q4R. All documents can be located at: http://www.lockheedmartin.com/us/suppliers/tandc.html QR # QC1206 Government Source Inspection New: 05/11/11 Government inspection is required prior to shipment from Sellers facility. Upon receipt of this contract, Seller shall promptly notify and furnish a copy of this contract and all subsequent change orders to the government representative who normally services Sellers facility so that the appropriate planning for government inspection can be accomplished. During performance of this contract, the Sellers and Sellers subcontractors Quality and Manufacturing processes are subject to review, verification, and analysis by authorized Government

http://www.lockheedmartin.com/us/suppliers/tandc.html


Page 7 of 43

Representatives. The inspection required by this clause may occur at any manufacturing or processing sequence as specified by the government representative. If a government representative does not normally service Sellers facility, Seller shall furnish a copy of this contract to the nearest Defense Contract Management Agency (DCMA) office. In the event the Government representative or DCMA office cannot be located, Seller shall immediately notify Buyers Authorized Procurement Representative. Evidence of government inspection (Eagle Stamp or DCMA representative signature) shall be shown within the shipping documentation. Government inspection of goods or services provided hereunder shall be performed at Seller's address shown on this contract or contract change unless a different address is specified. QR # QC1300 Determination of (Prime) Design Authority and Appropriate Specifications New: 9/30/07 Revised: 10/02/09 Suppliers shall use technical data retrieved from the secure GKN Virtual Community website to determine the Prime Design Authority, location of the Prime Design Authority, and the appropriate aircraft program. The Prime Design Authority and its location shall be used to determine the appropriate process specifications, material specifications and other relevant technical data to be utilized during all fabrication processes. If such processes are accomplished via sub-contractors, it is required that this information be transmitted (flowed down) to said sub-contractors. Suppliers shall process / fabricate to the latest revisions of customer / design authority specifications and technical data as identified on the GKN Prime Design Authority Specification Matrix at the start of manufacture. The Specification Matrix is available on the GKN Supplier Portal and it is the suppliers responsibility to review the latest version of this matrix at the start of manufacture. Any questions regarding the Specification Matrix should be directed to the GKN Buyer or Supplier Quality Engineer. QR # QC1305 Material Substitution Prohibition Boeing H900 Paragraph 26 Flowdown (Modified). New: 4/18/2013 26. MATERIAL SUBSTITUTION PROHIBITION A. Unauthorized Material Substitution (General) Unauthorized material substitutions are not permitted on Buyers Goods. Unauthorized material substitution includes any deviation from the engineering definition of a raw material. Engineering definition includes Buyer design drawing and applicable specifications, product specification, form, size, shape, chemistry, melt method, origin, temper/condition, product testing or surface finish. Alternate materials specified in the engineering definition (and often described as approved material substitutions therein) do not constitute unauthorized material substitution. Terms and definitions for metallic materials and processing used herein are clarified in ARP1917.


Page 8 of 43

Contact Buyers Authorized Procurement Representative for details regarding deviations to authorized materials. Seller agrees and understands that such deviations only apply to this purchase contract, and only as indicated in the Buyers authorized document. B. Metallic Materials (Specific) Temper or Condition Conversion - Unless specifically authorized by the engineering definition, conversion of a raw material (i.e. heat treat to change the temper or condition of the material) constitutes material substitution of the condition provided by the manufacturer. Metallic Raw Materials Buyers engineering drawings may refer to obsolete or superseded specifications covering several forms, thicknesses, widths, etc. of the alloy or alloys. The required characteristics of these materials are defined not only by the objective test standards of the specification, but by the processes/methods by which this final form is achieved. These requirements are often captured in the definitions of the required material forms, and may not be explicitly called out in the detailed requirements. The raw material certification results from both the process used to make it and the tests to verify basic properties. Seller shall ensure that metallic materials covered by current or obsolete/superseded specifications are produced using the standard industry practices designed strictly for the production of stock to the specified thickness, diameter, width or cross sectional area, achieved by thermo-mechanical processing or casting process. Chemical, electrochemical and mechanical methods used for the removal of surface scale or contamination, or the production of the required surface finish, in accordance with the material specification are acceptable. Raw material must not be re-certified with respect to thickness, diameter, width or cross sectional area or product form. Machining or cutting of thicker product or other product forms shall not be supplied in lieu of specified product unless specifically authorized by Buyer. Raw material certifications for material or parts shall reflect the form and size of the raw material as originally manufactured by the raw material producer. C. Specification Supersession: For government specifications and standards canceled after June 1994, Seller and subcontractors at all tiers shall use the last active revision of the canceled specification and standard until an acceptable replacement is included in the requirements of this Contract. Contact the Buyers Authorized Procurement Representative in the event of any inconsistency in applicable specification or standard. D. Reports (Full Pedigree from melt to final product) - Raw material certifications shall show clear traceability to the manufacturer(s) of the raw material including ingot source, all thermo-mechanical processing (i.e. forging, rolling, drawing, etc), heat treatment, chemical processing and inspections as required by applicable raw material specification requirements.


Page 9 of 43

E. Chain of Custody (Disguising intermediate ownership) Suppliers shall not disguise the pedigree of material or chain of ownership by removal of a previous suppliers name, nomenclature or identification. F. Source of Additional Information - Buyers Authorized Procurement Representative. G. The substance of this Article shall be flowed in all subcontracts at every tier. QR # QC1400 Notification of NADCAP Findings New: 11/14/16 Supplier shall promptly notify GKN via written communication to GKN Buyer and/or Supplier Quality Engineer of any documented findings resultant from NADCAP audits. QR # QC1500 - Discretionary Government Surveillance New 2/1/07 Obsolete 2/17/07 QR # QC1900 Nonconformance Cost Recovery New 12/12/03 Revised: 6/1/16 Supplier is subject to charges for recovery of costs associated with any/all supplier-responsible nonconforming parts/materials. Such charges will at a minimum include:

Charge Category Part/Material Value <

$500 Part/Material Value > $500

Administrative Charge to process Nonconformance Documentation*

$250/Nonconformance Document

$250/Nonconformance Document

Rework required at GKN-STL** Minimum of $50/discrete

unit Minimum of $200/discrete unit

Correction of part mark errors/omissions at GKN-STL**

10% of discrete unit value $50/discrete unit

Additional charges may also apply where: parts or materials, as supplied by GKN and/or its customer, require scrapping at the supplier

as a result of the suppliers actions. supplied parts/materials require extraordinary rework at GKN or its customer. GKN suspects supplied product to have a nonconformance, and additional inspection/testing

is required to validate conformity. *NOTE: Charges will be assessed for nonconformance tags initiated through the identification of nonconforming parts/materials by GKN and/or its customers as well as those initiated as a result of suppliers own requests for disposition of nonconforming parts/materials.


Page 10 of 43

**NOTE: The location of rework (GKN vs. Supplier) associated with nonconformances received by GKN will be at the discretion of the GKN Buyer in order to ensure the timely supply of conforming parts/materials. QR # QC2000 GKN-STL Supplier Quality Assurance Manual New 12/12/03 Revised 02/26/09 In the performance of this purchase agreement, the Supplier is required to comply with the latest revision of the GKN Aerospace - St. Louis Supplier Quality Assurance Manual (MI 7.4-16). The contents of this manual, as well as all required forms, may be accessed at the following GKN Supplier Portal: http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx Where Quality Requirements (QRs) other than QC2000 invoked by a GKN purchase order are in conflict with the GKN Supplier Quality Assurance Manual, such QRs will supersede requirements defined within the manual. QR # QC2001 GKN Receiving Address New - 08/03/01 Obsolete 05/12/04 QR # QC2002 Engineering Rev Level Identification NEW 07/10/03 Seller shall record the end item part number, drawing level and engineering changes to which the delivered item has been manufactured to on the packing slip. QR# QC2004 GKN Inspection New 08/03/01 Obsolete 05/12/04 QR# QC2005 All Consigned Pre-Preg Material New - 07/10/03 Pending GKN St. Louis lab approval, all consigned pre-preg material will be allowed to be shipped up to 180 days from date of manufacture. QR# QC2006 Government Inspection (DLA) New - 08/03/01 Revised -3/19/02 Obsolete 9/30/07 QR# QC2007 Flight Safety / Critical Parts Traceability (Apache) New - 08/03/01 Revised: 12/04/08 Obsolete: 6/1/16

http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx


Page 11 of 43

QR# QC2009 Flight Safety Parts Program Plan & Program Planning Package (Apache) New 08/03/01 Revised: 03/19/02 Obsolete: 6/1/16 QR# QC2011 Records of Inspections, Test and Process Controls New - 08/03/01 Revised: 05/12/04 Seller shall maintain records of all inspections, tests, and process controls associated with fulfillment of this purchase order contract. Unless alternate record retention requirements are specified elsewhere in this Purchase Order or its attachments, (i.e. engineering specifications, additional GKN Quality Requirement which specified a longer retention period, etc.) these documents shall be on file and available to GKN for four (4) years following the end of the calendar year in which the final entry was made or three years after the final payment under this contract, whichever expires first. At any time during the retention period, at GKNs request, Seller will deliver said records, or any part thereof, to GKN, at no additional cost to GKN. QR# QC2015 Chemical / Physical Analysis Test Reports New - 08/03/01 Revised - 03/07/02 Obsolete 9/30/07 QR # QC2016 Boeing Hardness/Conductivity Testing Requirements New - 09/23/02 Note: For overload contracts not involving machining operations for machined parts or sheet metal operations for sheet metal parts, these requirements do not apply. Note: Exceptions to the following hardness testing requirement is granted for small complex geometry parts which, as a result of geometry do not allow for proper testing set-up or are subject to degradation as a result of testing. Engineering definitions that require hardness testing of a small, complex geometry part shall be coordinated with the procurement agent for changes. Hardness and conductivity testing shall be performed in accordance with P.S. 21203 and/or P.S. 21207 (unless otherwise specified by engineering specifications) as specified below. This requirement must be met, regardless of the source for heat treatment of the material. Unless otherwise specified by the engineering definition, the material shall also meet the acceptance requirements of P.S. 23023. Records of this testing shall be maintained by the Supplier. Hardness and conductivity is to be performed after all final operations, such as machining, forming, welding or thermal treatment. Hardness testing through any surface plating or coating is not recommended, and in no case shall hardness test impressions be made through a surface plating or coating which is harder than the base material. Only personnel qualified in accordance with Boeing IDS Process Specifications P.S. 21203 or 21207 (unless otherwise specified by engineering specifications) shall perform hardness and/or conductivity testing.


Page 12 of 43

Material Aluminum Other (except Titanium)1

Test Hardness Conductivity Hardness Conductivity Machined Parts Sample2 100% 100% None

Structural Sheet Metal Parts

Sample2 100% 100% None

Castings 100%3 None 100% None Forgings & Pressings Sample2 100% 100% None

Composites None None None None 1 Hardness and conductivity testing is not required for Titanium material of any kind. 2 Sampling plans should conform to sampling requirements noted below. 3 If values for a particular material type are not listed in P.S. 23023, hardness testing is not required. Sampling Requirements: Sampling inspection is allowed except for Mandatory Inspection Criteria (MICs) and Key Characteristics (KCs) noted on the engineering definition or if otherwise specified in the GKN purchase order, engineering definition and/or Special Manufacturing Instructions (SMI). MICs and KCs shall be verified on each part with variable data results recorded and made available on request. Sampling plans shall be in accordance with ANSI/ASQC Z1.4 for attribute inspections or ANSI/ASQC Z1.9 for variable inspections. Single sampling plan for Normal Inspection, General Inspection Level II, with no greater risk than an acceptance quality level (AQL) as noted in the table below for specific product types. Use of a sampling plan based on this requirement will constitute an approved sampling plan. Deviations from this requirement shall be submitted to GKN for review and submission to Boeing A & M St. Louis. Such deviations are subject to GKN and Boeing A & M - St. Louis disapproval.

Product Type AQL Machined Parts 2.5

Structural Sheet Metal Details 4.0 Castings, Forgings, and

Pressings 4.0

Composites 4.0 QR# QC2017 GKN Hardness / Conductivity Test for Machined & Sheet Metal Parts New - 08/03/01 Revised: 05/12/04 This QR has been superseded by QR # QC2016 Boeing Hardness/Conductivity Testing Requirements. If QC2017 GKN is invoked by GKN purchase order, please ensure compliance with QC2016 instead.


Page 13 of 43

QR# QC2018 GKN Castings, Forgings and Pressing Requirements New - 08/28/01 Revised: 03/07/02 Seller of castings, forgings and pressings shall in preparation for delivery:

1. Copies of test reports for fracture critical and fracture critical traceable hardware shall be included in the shipping documents to GKN.

2. Castings - suppliers packing sheet/certification shall include the master melt and/or heat number, heat treat lot number as applicable.

3. Forgings and pressings - suppliers packing sheet/certification shall include the mill heat number, heat treat lot or serial number as applicable.

4. Forging Flash - forging flash shall be removed in accordance with applicable specification requirement.

5. Processing Operations - (tensile testing of forging and pressings) - when forgings or pressings are shipped in the annealed or normalized condition (in accordance with specification requirements) and are to be heat treated later, the tensile specimens shall be heat treated to the specified condition on the end item (i.e. the finished machined part) and tested prior to shipment.

QR# QC2019 Pratt & Whitney Stamp New - 07/10/03 All documentation must have the applicable Pratt & Whitney source stamp per MCL Manual section F-17. QR# QC2020 Unconfirmed Failure Rejections New 9/23/02 In the event hardware delivered on this Purchase Order is rejected and returned by GKN to the Supplier and the Supplier is unable to confirm the reported failure, the Supplier shall provide the following to the Buyer and hold shipment pending GKN disposition:

Purchase Order Number Part Number Serial Numbers GKN Nonconformance Tag Number Applicable test procedures Results of special tests performed by the Seller Suppliers certification that test procedure used to verify the failure identified by GKN was

adequate to detect those failures. Supplier shall provide the number and revision of test procedure(s) used.

QR# QC2021 Supplier CAD/CAM Inspection Data Control per D650-14831-1 New 9/23/02 Revised 10/13/03 If Supplier has Boeing DPD Authority during the entire product manufacturing and verification process and QR # QC2026 is on this GKN Purchase Order, the Supplier is exempt from requirements


Page 14 of 43

in this QR. If Supplier has not received and maintained Boeing DPD Authority the requirements of this QR apply. Supplier CAD/CAM nominal inspection data derived from master dimension identifier (MDI), master dimension definition (MDD), master dimension surface (MDS) or non-dimensioned features in the engineering CAD model will be verified and stamped as approved by Boeing Supplier Quality Management and returned to the Supplier with a cover letter stating the part number and engineering release to which the data is approved prior to use as inspection media. The data may be submitted for verification in a variety of formats including coordinate data lists, CMM program nominals, dimensioned sketches or drawings, IGES files, etc. The approved data will be used as an element of the inspection media for the specified part number. Any change in Boeing engineering and/or supplier data will require update approval and/or verification by Boeing Supplier Quality Management. Supplier CAD/CAM Q.A. data shall be controlled in accordance with D650-14831-1. Supplier shall maintain records of controlled inspection data and shall make those records available to GKN and Boeing upon request. QR# QC2022 Requirements for Key Characteristics (KCs) New 9/23/02 Revised 07/10/03 When Key Characteristics are specified on the drawing or purchase contract, the Seller shall utilize 100% inspection for these characteristics or employ control per SAE AS9103 Variation Management of Key Characteristics. Data in support of either 100% inspection or control per AS9103 are to be made available to GKN and its customers upon request. Application of AS9103 does not invalidate the need to establish and document compliance with all requirements for First Article Inspection per AS9102. QR# QC2023 Boeing Process vs. Military/Industry/Team Equivalents (F-22) New 9/23/02 Obsolete: 6/1/16 QR# QC2024 Serialization/Traceability Requirements for Fracture Critical Category (F-22) Hardware New 9/23/02 Obsolete: 6/1/16 QR# QC2025 GKN Process Assessment/On-site First Article Review New 4/18/03 Prior to production part shipment approval, supplier is required to successfully pass an on-site verification of its First Article part as well an audit of applicable production part processes/systems including processes and systems designed to ensure serialization and traceability for critical parts as applicable. QR# QC2026 Quality Assurance for Digital Data per D6-51991 New 10/13/03


Page 15 of 43

When a supplier receives or uses Boeing digital data as authority for design and/or inspection, then the seller must comply with the requirements of D6-51991, Quality Assurance Standard for Digital Product Definition at Boeing Suppliers. QR # QC2027 Requirement for use of Boeing Specifications (F-22) New - 02/17/04 Obsolete: 6/1/16 QR# QC2028 Government Inspection (DoD, DCMA, DCMDI) New 08/03/01 Revised 9/30/07 Government inspection is required prior to shipment from your plant. Arrangements for government inspection under this contract will be made by U.S. Department of Defense (DoD), Defense Contract Management Agency (DCMA), Defense Contract Management District International (DCMDI), or Defense Logistic Agency (DLA). For the correct DCMDI office, please refer to the DoD Contract Administration Services (CAS) Component Listing at: http://www.dcma.mil/casbook/casbook.htm Upon receipt of this contract promptly provide the government representative who normally services your plant with a copy of the purchase order and also copies of all subsequent change orders so that appropriate planning for government inspection of the goods can be accomplished. Evidence of government inspection shall be shown on all shipping documents. QR# QC2029 FAR 43.13 Performance Rules & 145.57 Performance Standards New - 08/03/01 Revised: 05/13/02 Obsolete 4/26/06 QR# QC2030 Fastener Certifications New - 08/03/01 Revised: 03/07/02 If this contract is for the procurement of ASTM, ASME, SAE, MS, BAC, AN, or NAS specification fasteners, (bolts, nuts, screws, studs, washers, rivets, pins, etc. then the following applies: Certification stating materials, processes (including applicable inspection processes) and finished items were controlled and tested in accordance with requirements of this contract and applicable specifications and that such records are on file (unless the material was Buyer provided). The certification shall identify the original manufacturers and their lot numbers for each lot in the shipment. Multiple lots within a shipment shall be kept separated and clearly identified as to the original manufacturer and the lot number(s). A copy of the certification shall be included with the packing sheet for each shipment. QR# QC2031 Calibration MIL-Std 45662A New - 07/10/03 Obsolete 05/12/04


Page 16 of 43

QR# QC2032 Changes To Sellers Operations New - 07/10/03 Obsolete 05/12/04 QR# QC2037 Quantitative Test Results New - 08/03/01 Revised: 03/07/02 Seller shall submit with each lot, quantitative results of all tests required by the procurement specification and applicable part drawing. In addition, when part size or configuration prohibits conventional testing, the Seller shall obtain coupons of the same material and heat treat lot. These coupons shall be prepared in such a manner as to facilitate testing requirements and yield acceptable test results. Test results obtained from coupons shall be submitted with each lot and shall be identifiable to the shipment. Sellers other than original manufacturers shall not rework, alter, or modify any manufactured item. Manufacturers performing rework shall, on completion, submit the item to required specification testing. The Seller shall identify unit packages and their associated records. Such identification shall include the heat treat lot number and/or the inspection lot number. Exceptions:

1. Coupon testing will not be required for fatigue life, tension-tension fatigue requirements, and mechanical property testing, except when specifically required by the applicable procurement specification.

2. Coupon testing does not apply to component type fasteners. QR# QC2040 Certificates of Conformance New 08/03/01 Revised: 10/02/09 Seller shall furnish a certificate of conformance, signed by a company representative, attesting to the compliance with all requirements of this purchase order. Such certificates shall contain lists of individual part/material serial numbers where required by specification. Seller shall maintain records of inspections, tests, and process controls (including sub-tier supplier/processor certificates of conformance/test reports) in accordance with record retention requirements imposed by this contract, which serve to substantiate this certification. The GKN buyer shall be notified and approve any exception prior to shipment. Certification shall attest to the following:

1. Material used on this purchase order conforms to all applicable specifications. Material Alloy must be listed on the submitted Certificate of Conformance with the delivery. If material is furnished by GKN, so indicate.

2. All requirements of this purchase order, including specification and revision level conformance, and compliance with applicable GKN Quality Requirements have been met. All special processes performed must be listed on the submitted Certificate of Conformance with the delivery.

3. Distributors and jobbers must, in addition to the above certification, include the manufacturers name for each item shipped.

Attach one (1) copy of the certification to the material involved and one copy to the shipping document(s) with each shipment. Performance of this purchase order will not be complete and final


Page 17 of 43

payment will not be made unless the required certifications of conformance have been signed or stamped by a company representative and are received by GKN. NOTE: In addition to the above, suppliers of raw materials will be required to support GKN periodic verification and validation of these materials to specified requirements when and as directed by the applicable GKN Buyer. Support of these activities may require one or more of the following:

1. Periodic submission of the actual raw material test report (mill test report, e.g.) that states the lot of material has been tested, inspected, and found to be in compliance with the applicable material specifications

2. Submission of material samples for subsequent validation testing by GKN, or 3. Substantiation to support the suppliers own program of periodic validation and verification

where they are not the raw material manufacturer themselves. Test reports will list the specifications, including revision numbers or letters, to which the material has been tested and/or inspected and the identification of the material lot to which it applies. When the material specification requires quantitative limits for chemical, mechanical, or physical properties, the test report will contain the actual test and/or inspection values obtained. Certifications for physical properties will likewise show actual values. If Supplier supplies converted material produced by a raw material manufacturer, Supplier is responsible for ensuring performance of all physical tests where the manufacturing process has altered the properties from what had been certified by the raw material manufacturer. The data submitted must reflect the condition of the material as offered for delivery. This data is in addition to the raw material manufacturers test report required above. QR# QC2041 Responsibility for Raw Material Test Report Validation New 03/14/03 Obsolete 9/30/07 Revised 10/09/2015 When Seller utilizes test reports to accept Seller purchased raw material, the following requirements apply: Test reports shall be checked 100% against Sellers requirements and applicable specifications. Validation test requirement: Seller shall periodically validate test reports for raw material accepted on the basis of test reports. That validation shall be accomplished by Seller or other independent party through periodic, scheduled tests of raw material samples. Schedules for frequency of tests will be established by Seller based on historical performance of the raw material supplier. Seller shall retain test reports provided by the raw material supplier, as well as Sellers validation test results as quality records traceable to the conformance of Goods, as specified elsewhere in this Contract. Buyer and customer furnished raw material is not subject to the validation test requirement. Seller shall implement processes and procedures in support of this clause. QR# QC2042 Foreign Object Debris/Foreign Object Damage (FOD) Prevention and Control New 04/26/16


Page 18 of 43

Seller is required to establish and maintain a FOD prevention program in accordance with D6-85622, Foreign Object Debris/Foreign Object Damage (FOD) Prevention Requirements for Boeing Suppliers. Seller shall implement processes and procedures in support of this clause. QR# QC2046 Part Identification & Traceability New 08/03/01 Revised: 03/07/02 Obsolete 9/30/07 QR# QC2047 Part Identification & Date of Manufacture New 3/14/03 In addition to those part marking requirements identified on the associated blueprints/drawings, Supplier shall identify each item/part with the date of manufacture or a more process-specific lot designation in an area adjacent to the part mark identification. Identification shall be performed using those same methods and materials identified within the applicable part mark specifications referenced on the associated blueprints/drawings. QR # QC2050- Use of Approved Suppliers / Processors New 12/04/08 The customer or design authority governing parts made or procured by GKN may restrict the performance of certain Special Processes required in the manufacture of these parts to a limited group of companies on an Approved Supplier List (ASL). The company actually performing the Special Process (whether it be GKNs supplier or a subcontractor performing work for GKNs supplier) shall be listed on the ASL published by the design authority as qualified to perform that particular Special Process. If the supplier needs information about a design authoritys ASL, they should contact the GKN Buyer. It is GKNs suppliers responsibility to impose this requirement on their subcontractors per QC2055. QR # QC2051 Disclosure and Approval of Subcontracted Processes New 5/20/11 During performance of this contract, the Seller is required to submit to GKN for approval all plans to subcontract fabrication or processing of any kind. Subcontracting any work required to complete this contract without written consent from the GKN buyer is prohibited QR # QC2055- Flowdown of Purchase Order & Quality Requirements to Sub-tier Suppliers New 12/04/08 All Purchase Order Requirements and Quality Requirements invoked on a Purchase Order to a GKN supplier shall be flowed by the supplier to all related sub-tier suppliers (as applicable) performing work on the items listed in said Purchase Order. In addition, it is the suppliers responsibility to provide all documentation/information related to the Purchase Order Requirements and Quality Requirements to its sub-tier suppliers and enforce said requirements.


Page 19 of 43

QR# QC2060 Boeing 787 Shipping Requirements New: 6/1/16 Suppliers of parts for Boeing 787 aircraft are required to mark all crates/packaging with stamped placards indicating which side should be oriented upwards (This Side Up). Crate footings shall be oriented on the underside at all times through duration of shipment to GKN, in order for product to be safely unloaded with a fork truck. QR# QC2074H Single Lot / Date Parts New 08/03/01 Revised: 03/07/02 All parts supplied under this purchase order must be of the same Lot/Date Code. QR# QC2077D GKN Use of Boeing Qualified Sources New 08/03/01 Revised: 05/12/04 This QR has been superseded by QR # QC3030 Use of Boeing Approved Special Processes. If QC2077D GKN is invoked by GKN purchase order, please ensure compliance with QC3030 instead. QR# QC2080 Quality System (MIL-I-45208) New 08/03/01 Obsolete 05/12/04 QR# QC2080A Quality System (MIL-Q-9858) New 08/03/01 Obsolete 05/12/04 QR# QC2080C GKN Quality System (AS9100) New 08/03/01 Revised: 02/26/09 Seller shall establish and maintain a quality assurance system that meets the requirements of the latest revision of SAE AS9100, Quality Management Systems Requirements for Aviation, Space and Defense Organizations. Registration by an independent registrar is not required. Future registration will be required to maintain the status of active supplier for GKN Aerospace - St. Louis. Non-registered suppliers are subject to internal process audits to determine compliance to the latest revision of SAE AS9100 by GKN or a GKN designate. QR# QC2081 Supplier Inspection New 08/03/01 Obsolete 05/12/04 QR# QC2081A GKN Control of Nonconforming Product New 08/03/01 Revised: 12/04/08


Page 20 of 43

The supplier shall control nonconforming product. This control shall provide identification, documentation, segregation (when practical) and notification of qualified supplier Quality Assurance personnel. The suppliers Quality Assurance personnel, with the assistance of Engineering if required, shall examine nonconforming material to evaluate if the material can and/or should be dispositioned rework to specification or scrap (notify GKN procurement before disposal for possible alternate use). If product cannot be dispositioned as listed above, it shall be designated for GKN Aerospace - St. Louis Material Review Board (MRB) action. The supplier shall document the nonconformance on Form MI 7.4-16(b) Supplier Nonconformance Record and submit this document to their GKN Buyer. Any nonconformance-related attachments should be enclosed on Form MI 8.1-11 (e) or Form MI 8.1-11 (f) and submitted along with MI 7.4-16(b). The GKN Buyer will assign a GKN External Nonconformance Number and provide it to the supplier to revise Forms MI 7.4-16(b), MI 8.1-11 (e) or MI 8.1-11 (f) and to include on Form MI 7.4-16 (d) Deviated Supplied Parts Cover Sheet. If GKN elects to bring the nonconforming part in, the supplier shall complete MI 7.4-16 (d) and submit it to GKN along with the nonconforming part, the completed MI 7.4-16 (b) and the GKN External Nonconformance document. In addition, all supplier Certificates of Conformance shall note the GKN External Nonconformance Number. NOTE: The supplier is not authorized to ship the product to GKN unless explicit written direction has been provided by the GKN Buyer. Finally, when the product is delivered to GKN, the GKN nonconformance document number should be included in the product identification even if the nonconformance document has been closed. The supplier shall retrieve the latest revisions of the documents above from their GKN Buyer or from the public library of the GKN Supplier Portal at http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx. QR# QC2086 Quality System (Attached Requirements) New 08/03/01 Obsolete 05/12/04 QR# QC2087 GKN Critical Parts Traceability and/or Serialization Information New 08/03/01 Revised: 09/23/02 This part includes a requirement for inclusion of critical traceability and/or serialization data. Supplier shall provide and certify, at minimum, the following information for each part supplied:

1. Part Number, Part Dash Number, Part Serial Number, Supplier Name, Supplier Internal Control Number

2. Starting Stock Part and Dash Number, Serial Number, Stock Supplier 3. Heat Treat Vendor & Lot Number, 4. Raw Material Specification Number, Parent Plate/Forging Lot Number/Extrusion I-Teat Lot,

Producer. 5. Non-Destructive Test Method, Processor, Inspector ID, NDT Technique Number, 6. All Rejection Document Numbers



Page 21 of 43

QR# QC2088 GKN Boeing Non-Destructive Technique Approval New 08/03/01 Revised: 05/12/04 Seller shall provide certification that Non-Destructive Testing (NDT) technique approval has been received from Boeing prior to shipment from Sellers facility to GKN. QR# QC2089 Special Tooling Control (Boeing Integrated Defense Systems (IDS)) New 02/25/09 Revised: 6/1/16 If this Quality Clause is invoked, refer to QC2090. QR# QC2090 Property Control New 03/07/02 Revised: 05/13/02 In the performance of this purchase agreement, the Supplier is authorized to use special tooling and/or test equipment identified herein. Such tooling and/or equipment are considered the property of GKN, GKN customer(s) or the Government and will be used solely for its intended purpose unless otherwise approved by GKN. No such tooling or equipment shall be destroyed, disposed of, or transferred without the written consent of GKN Aerospace St. Louis. In the performance of this contract the Supplier shall be responsible for all periodic, inventory checks, inspections, maintenance and refurbishment or replacement required to manufacture, test and deliver the items ordered under this purchase agreement. The Supplier will be liable for shortages, loss damage or destruction to tooling or equipment provided in support of this purchase agreement. The Suppliers liability shall apply until GKN provides written release of such liability without regard to termination or expiration of this purchase agreement. The Supplier shall promptly investigate and report any loss, damage, or destruction of GKN, Customer or Government tooling or equipment. The reports shall include the following at a minimum:

Purchase Agreement/Order number Description and item identification number Estimated replacement or repair cost Date and time of loss, damage, or destruction Actions taken to prevent further loss, damage, or destruction and to prevent repetition of

similar incidents Statement that no insurance costs or other means of the subcontract covering loss, damage,

or destruction of property were charged to this purchase agreement. Security classification of the item, if any All known facts or circumstances that led to the loss, damage, or destruction and a

certification that the item was being used for its intended use. The Supplier will assure the identification stickers, tags will remain on the tooling/equipment and that the identification stickers or tags are legible. The Supplier shall certify that the tooling/equipment provided herein will be recorded and maintained on the Suppliers property records.


Page 22 of 43

All Boeing or government-owned tools that are used for IDS production, fabricated, reworked or repaired by approved tooling suppliers, and Boeing, Government or supplier-owned tools that are used for the acceptance of products fabricated for Boeing Integrated Defense Systems (IDS) or its customers shall be controlled in accordance with D950-11059-1 IDS Seller Special Tooling Requirements. Written approval from GKN is required before any Government or Customer owned tools are reworked or repaired except for standard line maintenance. The Supplier will maintain tools and equipment. At a minimum, tool maintenance shall consist of the following:

Replace tooling pins and keys as required. Repair elongated tooling holes and worn keyways. Clean and polish working surfaces of dies as required to prevent scoring or marking of parts. Protect entire die with anti-oxidant after each run of parts. Any other minor rework not to exceed three (3) man-hours.

Cost of any tool rework or replacement, which is not covered by the above, shall be negotiated separately. The Supplier will permit GKN, the Government, or GKN customers reasonable access to any customer or Government property. The Suppliers shall clearly identify all return shipments of tools or equipment with the purchase agreement number and the tooling/equipment identification number(s). Shipments must be accompanied by the appropriate shipping documents. QR# QC2091 F15 Tooling Precedence New 7/26/06

Seller will manufacture all goods to be delivered under this contract in accordance with the buyer furnished build-to-package, which may include, but is not limited to, the GKN SMI, buyer furnished tooling and engineering drawings. In cases where the buyer furnished tooling and engineering drawings are different, the tooling shall take precedence as defined in the GKN SMI. Engineering dimensional call-outs shall not be required during First Article Inspection when a tool is the controlling media, as defined in the GKN SMI and the feature is validated to the buyer furnished tool.

QR# QC2092 Special Tooling Control (Boeing Puget Sound) New 9/23/02 All Boeing or government-owned Special Tools that are fabricated, reworked or repaired by approved tooling suppliers, and Boeing, Government or supplier-owned Special Tools that are used as media of inspection (MOI) for the acceptance of products fabricated for Boeing Military Aircraft and Missile Systems Group (Puget Sound) or its customers shall be controlled in accordance with D658-10024-1 Supplier Fabricated/Held/Owned Special Tools Inspection, Acceptance, and Control. This document defines Quality Assurance requirements for acquisition and utilization of Special Tools, Tooling Supplier Surveys, Tool Design Reviews, First Product Inspections, Tool Routines, Release Status Control, Tool Inspections, Shipping/Receiving Screening Inspection, and Tool Discrepancy Control.


Page 23 of 43

QR# QC2093 Quality System (Boeing A0436 Latest Revision) New 06/12/04 The following requirements apply to the manufacture of parts and/or materials which are Boeing designed and that are produced for subsequent GKN delivery to Boeing Integrated Defense Systems, St. Louis. The Supplier to GKN for such parts/materials shall establish and maintain a quality assurance program in accordance with the latest revision of Boeing report number AO436. This document which outlines requirements supplemental to SAE AS9003 may be accessed at: http://www.boeing.com/companyoffices/doingbiz/quality QR# QC2094 Quality System (Boeing A0436 REV. Q) New 09/23/02 Revised 6/12/04 This QR has been replaced by QC 2093. Suppliers are to ensure compliance with QC2093 as applicable when QC2094 is invoked. QR# QC2095 Quality System (Boeing A0436) New 03/07/02 Revised 6/12/04 This QR has been replaced by QC 2093. Suppliers are to ensure compliance with QC2093 as applicable when QC2095 is invoked. QR# QC2096 MDC/MDHS Approved Sources (Apache) New 03/19/02 Revised: 05/13/02 Obsolete: 6/1/16 QR# QC2097 Boeing Approved Sources New 03/19/02 Material of this purchase order shall be procured from an Approved Supplier as indicated on the applicable Boeing Approved Vendor List (AVL) or Qualified Product List (QPL). Shipment Documentation: Each shipment shall be accompanied by a certification stating the name and address of the Boeing AVL source or the Government QPL source and the specification number.


Page 24 of 43

QR# QC2098 First Article Inspection (AS9102) New 04/08/02 Revised: 12/05/08 Suppliers of engineered components/parts shall perform, retain, and submit a First Article Inspection Report in accordance with the latest revision of AS9102 Aerospace First Article Inspection Requirement. Copies of the completed First Article data shall be submitted to GKN with the shipping documents of the first part or directly to the appropriate GKN Supplier Quality Engineer or Buyer and shall be maintained at the suppliers facility. GKN reserves the right to request data packages, and the requested data must be supplied within 5 business days of the request. The suppliers own equivalent forms may be used in place of those contained within AS9102 provided all required information is included. First Article Inspection Reports previously prepared in full compliance with QC 2098 are acceptable to GKN and may be retained in lieu of repeating the First Article Inspection, provided it has not been 2 years since parts were last manufactured. Any change to the manufacturing process after an approved First Article requires notification in writing to GKN. Partial first articles are required per AS9102 section 5.3 and the requirements for submission and retention of partial first articles is the same as initial first articles. Supplier must inform GKN buyer in writing (email is acceptable) when a new or partial first article is required, as soon as the supplier plans a change, due to a change in; manufacturing location, process, equipment, sub contracting of operations, or change in tooling. Copies of AS9102 and associated forms may be obtained by contacting SAE at http://www.sae.org QR# QC2099 F/A-18 E/F Control of Fracture & Maintenance Critical Parts (Dwg. 74A900054) New 04/08/02 Revised: 05/13/02 Supplier shall ensure compliance with latest revision of Boeing drawing # 74A900054 Control of Fracture and Maintenance Critical Parts for the F/A-18 E/F Aircraft. QR# QC2100 F/A-18 E/F Fracture Critical Traceable Parts (Dwg. 74A900053) New 04/08/02 Revised: 05/13/02 Supplier shall ensure compliance with latest revision of Boeing drawing # 74A900053 Serialization and Traceability Requirements for F/A-18 E/F Fracture Critical Traceable Parts. QR# QC2101 F/A-18 C/D Fracture & Maintenance Critical Parts (Dwg. 74A900004) New 09/23/02 Supplier shall ensure compliance with latest revision of Boeing drawing # 74A900004 Control of Fracture and Maintenance Critical Parts for the F/A 18 Aircraft.


Page 25 of 43

QR# QC2102 F/A-18 C/D Serialization and Traceability Requirements (Dwg. 74A900003) New 09/23/02 Supplier shall ensure compliance with latest revision of Boeing drawing # 74A900003 Serialization and Traceability Requirements for F/A 18 Fracture Critical Parts. QR# QC2103 Traceability/Serialization per 17P9M2005 New 11/06/02 This part requires traceability/serialization in accordance with the latest revision of Boeing document 17P9M2005. QR# QC2104 Special Control per 17P9M2004 New 11/06/02 This part requires special control in accordance with the latest revision of Boeing document 17P9M2004. QR# QC2105 T-45A Fracture Critical Traceable Parts New 7/10/03 Supplier shall ensure compliance with the latest revision of Boeing Drawing # DA000A1000 T-45A Control of Fracture Critical Parts for serialization and traceability of fracture critical parts. QR# QC2110 Control of Materials and Processes for Designated Parts and Components of Boeing Products per D6-1276 New 7/1/08

QR # QC2200 Acceptance Authority Media (AAM) (BOEING X31764)

New 07/17/17

Supplier shall comply with AS/EN/JISQ requirements and 14CFR Part 21.2 regarding the application of the Acceptance Authority Media ( AAM ) requirements. Supplier shall, within its organization and its supply chain, ensure that the use of AAM is clearly defined within its Quality Management System (QMS ). Seller shall, upon Flightline request, be able to demonstrate evidence of communication to its employees and to its supply chain; use of AAM must be considered as a personal warranty and conformity. Supplier shall maintain compliance to the AAM requirements by assessing its process and supply chain as part of its internal audit activities. The areas of focus of this assessment shall include but are not limited to:

Authority Media Application Errors (i.e. Omission, Typos, Legibility, etc.) Authority Media Application Untimely Use (i.e. Documentation is not completed as planned,

Stamp/Sign as you go, etc.) Authority Media Application Misrepresentation (i.e. Uncertified personnel, Falsification of

documentation, Work not performed as planned, etc.) Authority Media Application Training Deficiencies (i.e. Ethics, Culture awareness, Proper use of authority media, etc.)


Page 26 of 43

QR # QC 2800 Winglet Technology Program Quality Requirements New - 01/20/04 Obsolete 4/26/06 QR # QC3000 First Article Engineering Evaluation New 04/08/02 Revised 9/30/07 Parts covered by this Quality Requirement are subjected to First Article Engineering Evaluation by Engineering Authority. Supplier shall perform a first article inspection in accordance with the latest revision of AS9102 Aerospace First Article Inspection Requirement. Two (2) copies of the First Article Inspection Report are to be submitted with the shipment of parts. Suppliers own equivalent forms may be used in place of those contained within AS9102, provided all required information is included. Copies of AS9102 and associated forms may be obtained by contacting SAE at http://www.sae.org Supplier must notify the applicable GKN Buyer and/or Supplier Quality Engineer at least 10 days prior to the time the item(s) will be ready for First Article Inspection. It is the suppliers responsibility to meet all specifications and other relevant purchase order requirements. Any results that do not meet specification requirements are cause for the supplier to withhold First Article parts and documentation. Suppliers are expected to expend every effort in order to correct the part/process so that all design record and purchase order requirements are met. If the supplier is unable to meet any of these requirements, the applicable GKN Business Unit Buyer and/or Supplier Quality Engineer shall be contacted immediately. First Article Data Record Retention Requirements Suppliers are to retain copies of First Articles for a period of 7 years, or in accordance with other Quality Requirements cited on the purchase order, whichever is longer. GKN Aerospace Services St. Louis and its customers reserve the right to attend and witness any/all First Article inspections as conducted at the suppliers facility. QR # QC3010 Manufacturing Process/Quality Systems Reviews New 04/08/02 Revised 01/20/04 Suppliers manufacturing processes, quality systems, and associated records/documentation are subject to review, verification, and analysis by GKN personnel, GKN Customer personnel, and/or representatives of applicable government and/or regulatory agencies/authorities on the suppliers premises at any time. QR # QC3020 - GKN/Customer/Government - Product, Quality System and Mfg Process Surveillance New 04/08/02 Revised 2/10/07

http://www.sae.org/


Page 27 of 43

During performance of this contract, Seller and Sellers sub-tier suppliers quality systems, manufacturing processes, associated records/documentation and product (as supplied under this contract) are subject to on-site (at supplier premises) review, verification, and analysis by GKN personnel, GKN Customer personnel, and/or representatives of applicable government and/or regulatory agencies/authorities. These reviews may be conducted on either a random or 100% (full time) basis. Supplier will be notified in advance should GKN, GKNs customer, and/or government regulatory agencies/authorities elect to invoke this right. Government inspection or release of product related to this contract prior to shipment is not required unless Seller is otherwise notified or a Form DD250 Government shipping document is required. If requested, Seller shall provide a copy of this contract to the Government Representative upon receipt. QR # QC3030 Use of Boeing Approved Special Processes New 04/08/02 Revised: 06/12/04 The following requirement applies to the manufacture of parts and/or materials which are Boeing designed and that are produced for subsequent GKN delivery to Boeing. The Supplier shall be listed or shall utilize sources listed in the latest revision of Boeing Document D1-4426, Boeing Approved Process Sources, whenever the manufacturing and inspection type processes listed in D1-4426, or their equivalent, are used in performance of this contract, except as noted in D1-4426. If the supplier is not on distribution for the D1-4426 document, a copy may be referenced on the Boeing Web-site at http://active.boeing.com/doingbiz/d14426/index.cfm. Supplier shall impose this requirement on their subcontractors as well. QR # QC3040 Retention of Inspection Records New 04/08/02 Revised 05/13/02 Supplier shall certify that materials, processes and/or delivered items will be controlled and tested in accordance with and meet specified contract requirements and applicable specifications, and that applicable records are on file subject to examination and will be furnished to GKN upon request. Supplier shall include with the packing slip for each shipment a completed copy of the Supplier Certificate of Conformance form. A duplicate copy of this document is to be sent to the applicable GKN buyer. Supplier shall retain production records of quality control, reliability and inspection for a period of seven (7) years from date of final payment unless otherwise specified on the PO. Supplier will have a documented procedure on record retention defining specific records and applicable retention periods/methods. QR # QC3050 Disposition of Nonconformances (Boeing Philadelphia) New 04/08/02 Obsolete: 6/1/16 QR # QC3060 Corrective/Preventive Action New 05/13/02 Revised 3/14/03

http://active.boeing.com/doingbiz/d14426/index.cfm


Page 28 of 43

Supplier shall provide GKN with documented Corrective/Preventive Action for any/all supplier corrective action requests initiated by GKN procurement representatives. Supplier shall respond using the appropriate GKN Supplier Corrective Action Response Form as supplied by GKN and/or any applicable GKN Customer response forms. Failure to provide timely and comprehensive corrective/preventive action responses in a timely manner may result in negative impact to the suppliers GKN Supplier Performance Indicator rating. QR # QC3070 Quality System Requirements (Boeing X-23784) New 5/13/02 Revised 4/26/06 Supplier is required to maintain a quality system in compliance with the latest revision of Boeing form X-23784. GKN reserves the right to conduct surveillance audits at the suppliers facility to determine that such compliance is maintained. QR # QC3075 Part Acceptance Stamping New 03/14/02 Parts supplied under this purchase order are to be individually acceptance stamped by appropriate supplier personnel in accordance with systems described in Boeing form X-23784. QR # QC3080 Checklist Compliance New 5/13/02 Revised 4/26/06 Supplier is to complete the latest revision of Boeing Checklist Form #57767 prior to each shipment in order to ensure compliance with applicable GKN contract requirements. If supplier fails to comply with any such requirement, GKN may back bill the supplier $200 per occurrence to correct the non-compliance. QR # QC3085 Comanche Program Flight Safety (Helicopter Only) New 04/18/03 Obsolete 4/26/06 QR # QC3090 Packaging, Marking and Shipping (Boeing Helicopter) New 05/13/02 Obsolete: 6/1/16 QR # QC4000 Approved Process Sources (Comanche) New 10/11/02 Obsolete 4/26/06 QR # QC4001 Raw Material Test Results (Comanche) New 10/11/02 Obsolete 4/26/06


Page 29 of 43

QR # QC4002 Non-Destructive Testing (NDT) Certification (Comanche) New 10/11/02 Obsolete 4/26/06 QR # QC4003 Compliance with MIL-I-45208A or Equivalent (Comanche) New 10/11/02 Obsolete 05/12/04 QR # QC5000 Use of Chemtronics NMR (F-22) New 10/11/02 Revised 4/26/06 Obsolete: 6/1/16 QR # QC5001 Software Control in accordance with DOD-STD-2168 (Boeing F-22) New 10/11/02 Obsolete: 6/1/16 QR # QC5002 Processor Certification Requirements (Boeing F-22) New 10/11/02 Obsolete: 6/1/16 QR # QC5003 Manufacturing Plan Approval (Boeing F-22) New 10/11/02 Obsolete: 6/1/16 QR # QC5004 Boeing F-22 Processor Approval per 5PD90505P New 10/11/02 Obsolete: 6/1/16 QR # QC5005 Mill Test Reports (Boeing F-22) New 10/11/02 Obsolete: 6/1/16 QR # QC5006 Variable Inspection Data Requirements (F-22) New 10/11/02 Obsolete: 6/1/16 QR # QC5007 Compliance with Engineering Requirements (Boeing F-22) New - 10/11/02 Obsolete: 6/1/16


Page 30 of 43

QR # QC5008 Subject to Chem-tronics Source Inspection (F-22) New- 10/11/02 Obsolete: 6/1/16 QR # QC5009 Supplier Certificate of Conformance Requirements (Boeing F-22) New - 10/11/02 Obsolete: 6/1/16 QR # QC5100 Nonconforming Material Control (Northrop Grumman) New - 08/26/04 Revised 12/04/08 When invoked, this Quality Requirement supersedes Quality Requirement # QC2081A. Nonconforming material must be identified, documented, evaluated, segregated, and dispositioned to prevent its unintended release or use. The suppliers disposition authority of nonconformances is limited to rework to specification, return to supplier and scrap. These terms are defined as follows:

1. Rework - Restore material to specification compliance in accordance with required process(s) and addressed by governing process specification(s). Parts subject to subsequent processing not authorized by specification shall be submitted to GKN for disposition. Specific rework instructions shall be provided with rework dispositions.

2. Return To Supplier - Return of subcontractor product found to be discrepant for subsequent rework or replacement.

3. Scrap - Permanent removal from production and destruction of product found to be unfit for use. Scrapped product shall be controlled until destroyed.

4. MRB - If product cannot be dispositioned as listed above, it shall be submitted to GKN Aerospace St. Louis for Material Review Board (MRB) action using Form MI 7.4-16(b) Supplier Nonconformance Record. Any nonconformance-related attachments should be enclosed on Form MI 8.1-11 (e) or Form MI 8.1-11 (f) and submitted along with MI 7.4-16(b). The GKN Buyer will assign a GKN External Nonconformance Number and provide it to the supplier to revise Forms MI 7.4-16(b), MI 8.1-11 (e) or MI 8.1-11 (f) and to include on Form MI 7.4-16 (d) Deviated Supplied Parts Cover Sheet. If GKN elects to bring the nonconforming part in, the supplier shall complete MI 7.4-16 (d) and submit it to GKN along with the nonconforming part, the completed MI 7.4-16(b) and the GKN External Nonconformance document. In addition, all supplier Certificates of Conformance shall note the GKN External Nonconformance Number. NOTE: The supplier is not authorized to ship the product to GKN unless explicit written direction has been provided by the GKN Buyer.

The supplier shall retrieve the latest revisions of the documents above from their GKN Buyer or from the GKN Supplier Portal at http://www.gkn.com/aerospace/supplier-info/st-louis/Pages/Quality-Information.aspx.



Page 31 of 43

QR # QC5101 Quality Record Retention (Northrop Grumman) New - 08/26/04 When invoked, this Quality Requirement supersedes Quality Requirements #QC2011. The supplier shall maintain quality records in accordance with the applicable quality system standard (i.e. ISO 9001, AS/EN9100). The records shall be retained for a period of not less than ten (10) years from completion of purchase order (unless otherwise stated below). The supplier must impose this requirement on their sub-tiers. Records shall include, but are not limited to:

Evidence of inspection to assure adherence to applicable drawings or specifications and revisions

First Article Inspection Report The FAI shall be retained as a quality record for a minimum of three (3) years from completion of the last purchase order for that part number with the same revision level.

Test reports Periodic inspection and control of inspection media Records to indicate control of special tooling and special test equipment Test data records of all qualification and acceptance test performed Certification of personnel as required by specification and/or contract Raw material and process certifications Material review reports

QR # QC5102 Shipping Documentation Requirements (Northrop Grumman) New - 08/26/04 Revised 2/16/15 The supplier shall maintain quality records in accordance with the applicable quality system. 1) Packing Slips - Supplier shall provide a packing sheet or attachments for each separate

shipment with the following minimum requirements: a) Suppliers company name and address. b) Purchase order number, line item(s) and part numbers. c) GKN dispositioned nonconformance document number(s), as applicable. d) Interchangeable and Replaceable (I&R) designated control numbers. e) Required parts traceability forms, as applicable. Evidence of GKN source acceptance if purchase order required GKN source surveillance.

2) Certificate of Conformance - Supplier shall comply with GKN Quality Requirement #QC2040 Certificates of Conformance. All fabricated aluminum parts require 100% conductivity inspection. Use the QOS-0021, Seller Requirements for Temper Inspection by Electrical Measurement and/or Hardness Measurement (http://www.northropgrumman.com/suppliers/OASISDocuments/QOS-0021_Seller_Requirements_for_Temper_Inspection_by_Electrical_Measurement_or_Hardness_Measurement_Dated_7_31_12.pdf) to determine the required conductivity range. When a supplier is contracted to build and deliver a given part number to a specific engineering revision level, an engineering document that is either equal to or later in revision level is an acceptable means of performing product acceptance. A later revision of an engineering drawing includes

http://www.northropgrumman.com/suppliers/OASISDocuments/QOS-0021_Seller_Requirements_for_Temper_Inspection_by_Electrical_Measurement_or_Hardness_Measurement_Dated_7_31_12.pdfhttp://www.northropgrumman.com/suppliers/OASISDocuments/QOS-0021_Seller_Requirements_for_Temper_Inspection_by_Electrical_Measurement_or_Hardness_Measurement_Dated_7_31_12.pdfhttp://www.northropgrumman.com/suppliers/OASISDocuments/QOS-0021_Seller_Requirements_for_Temper_Inspection_by_Electrical_Measurement_or_Hardness_Measurement_Dated_7_31_12.pdf


Page 32 of 43

incorporation of revisions that would have been issued as addendums (Engineering Orders, Engineering Change Notices, etc) to the prior level change and are thereby incorporated in the later revision. Unless otherwise specified, the supplier shall work to the latest revision military process specifications referenced in the purchase order or the engineering documents.

3) Suppliers of Age-Sensitive Materials - Provide original manufacturing/cure date, lot number(s), expiration date or length of shelf life (if indefinite, so state). In addition, forward any special storage/handling instructions. Supplier is responsible to determine if acceptance test report submittal is required in accordance with applicable material specification. The supplier shall physically identify the shelf life expiration date on the deliverable product or the unit packaging according to the applicable standard. Elastomeric material with No Shelf Life requirement or Unlimited Shelf Life shall be marked as such

4) Tooling Suppliers of Special Tooling or Special Test Equipment - In addition to sections A & B above, record the tool number, tool symbol, tool serial number (including the multiple number, as applicable), and assure a Northrop Grumman source surveillance stamp has been applied (see QR# QC5108 for additional tooling-related requirements).

5) Rework/Repair/Replacement/Modified Items - Suppliers Certification of Conformance and/or packing sheet document shall reflect the following requirements for rework, replacement, repair, modification, items returned to supplier, or work performed by supplier on-site at GKNs facility. a) The item(s) have been reworked, repaired, replaced, or modified (as applicable), in

accordance with respective nonconformance documents or purchase order. b) The item(s) meet the requirements of the engineering document(s). c) The original configuration and qualification status of the item(s) remains in effect (as

applicable). d) All applicable nonconformance document numbers or other references to insure traceability. e) Note: Discrepant material shall not be shipped to GKN or GKNs customer without prior

written approval from GKN Procurement and Material Review Board (MRB) Engineering. 6) Qualification Certification - When the drawing, procurement specification and/or purchase

order requires deliverable items to be Qualified, suppliers shall certify that materials, parts, assemblies and/or related contract Data Items have been approved and all components of a deliverable item have been inspected and/or tested to applicable Acceptance Test Procedures (ATP) and/or specification/control drawings (GKN, Northrop Grumman, and supplier originated). In addition, to sections A and B above, certification shall indicate revision level of engineering drawings, specifications, and applicable design/specification changes as stated in purchase order. Only authorized GKN Engineering and Procurement written consent shall allow end items to be delivered prior to completion of qualification testing.

7) Material Certifications - Supplier shall maintain a copy of all supplier procured raw material certifications, which must be readily retrievable and shall include material specification, description, alloy and condition. The supplier shall maintain the mill certification for procured metallic material that shall include physical properties, chemical analysis and lot number(s). Metallic raw material distributors (ref: SQAR Code A) shall include a copy of the original mills certification with the shipment of deliverable material. Suppliers material and sub-tier supplier certifications and test results shall be made available upon request.


Page 33 of 43

8) Process Certifications - Supplier shall obtain and furnish process certifications for all subcontracted processes with each shipment to GKN. Certifications shall state that parts have been processed/tested in accordance with Northrop Grumman Corporation, Military Aircraft Systems Division (NGMASD) approved procedures. This includes sub-tier supplier process certifications. Attach one (1) copy of the process certifications to the material involved and one copy to the shipping document(s) with each shipment. Process certification(s) shall identify the processor, part number, purchase order number, process specification number, identification of process method used, acceptance criteria document and the applicable quality control standard (CQS). Certifications must contain the document revisions. Additionally, suppliers shall maintain copies of all subcontracted special processes. Supplier shall also obtain and maintain sub-tier supplier process certifications. Suppliers process and sub-tier supplier processor certifications and test results shall be made available upon request.

9) Distributors of Standard Parts/Hardware - Standard and purchase parts distributors shall comply with the requirements of Northrop Grummans Quality Assurance Test Procedure (QATP). Suppliers may obtain this document from the Northrop Grumman Oasis website or they may request a copy from their GKN buyer. https://oasis.northgrum.com/

QR # QC5103 Nondestructive Test (NDT) Submittal Requirements (Northrop Grumman) New - 08/26/04 Supplier shall review the purchase order and associated drawings/drawing notes and related documents to determine if NDT is required. Submittal of NDT general procedures and part-specific techniques to GKN is required prior to production testing. Guidelines for the minimum content of general procedures/techniques are provided in the respective NDT process specification. After initial approval, any changes to subject documents must be resubmitted to GKN for approval. An EO change to a specification does not require resubmittal. A specification revision change does require submittal of a revised procedure/technique or letter of compliance. Suppliers using outside sources for NDT shall ensure that the selected NDT sub-tier has GKN & Northrop Grumman approval for the NDT procedure/technique used. An Approved Nondestructive Testing procedure/technique list is available on the Northrop Grumman Oasis website under Approved Processors. https://oasis.northgrum.com/ NDT technique shall be submitted to GKN in accordance with applicable specifications. In addition, suppliers will include with each shipment a certificate that lists the NDT performed. A record of the procedures or techniques used and actual results will remain on file for at least 10 years after shipment to GKN and will be furnished to GKN upon request. These records must include the inspectors signature or stamp and their NDT Certification Level. QR # QC5104 Control and Use of Digital Datasets (Northrop Grumman) New - 08/26/04 When digital datasets are required to manufacture product, the supplier shall comply with the SQAR Supplement for the Use and Control of Digital Datasets located in the Quality Requirements section of the Northrop Grumman Oasis website. https://oasis.northgrum.com/ QR # QC5105 Supplier Sub-tier Control (Northrop Grumman) New - 08/26/04


Page 34 of 43

Supplier is responsible for ensuring all items procured from its subcontractors conform to all requirements of the GKN purchase order. Supplier shall ensure all applicable provisions of this document are flowed down to its subcontractors. The sub-tier Supplier Quality system shall be compliant to the latest revision of either ISO9001or AS9100, except FAA Repair Stations. All sub-tier suppliers are also required to utilize AS9102 for their first article inspection (See Quality Requirement #QC2098 First Article Inspection (AS9102)). QR # QC5106 Northrop Grumman Special Process Requirements New - 08/26/04 When special processes listed in the Northrop Grumman Approved Special Processors List (ASPL), are required by drawing, specification, or purchase order, the supplier shall ensure that the processing source performing the work, including the supplier, is listed on the ASPL for that process prior to processing each batch of hardware. Special Processors are required to be accredited by the National Aerospace and Defense Contractors Accreditation Program (NADCAP). A processors approval will be determined based on the Northrop Grumman review of the latest NADCAP audit report for those processors with valid NADCAP approvals. For processors without a valid NADCAP approval, the affected processors are encouraged to get the NADCAP accreditation as soon as possible. Northrop Grumman has subscribed to NADCAP for the following process categories with a full transition to NADCAP by August 2003:

Nondestructive Testing Heat Treating Material Testing Laboratories Chemical Processes Coatings Welding

When the Processor requires the use of outside sources for salt spray, tensile testing and solution analysis, NADCAP accredited laboratories shall be used as of June 2004. The NADCAP approved Materials Test Laboratory list can be found on the PRI web site: http://www.pri.sae.org/ under Qualified Manufacturer List (QML) or eAuditnet. Northrop Grumman reserves the right to validate NADCAP compliances to any processes that are unique to Northrop Grumman or outside the scope of normal industry practice and/or NADCAP general audit practice. This requirement also applies to the first-tier suppliers with internal process capabilities. In addition, if the supplier utilizes any external special process sources, this requirement must be flowed down to the processing sources as soon as possible so as to avoid any problem during the transition in September 2003. All costs associated with NADCAP accreditation are to be borne by the processor. The Performance Review Institute (PRI), a nonprofit affiliate of the Society of Automotive Engineers (SAE), must perform NADCAP accreditation audits. Any detail information regarding NADCAP accreditation process including the audit schedule can be obtained from PRI at (724) 772-1616 or from the PRI Website: http://www.pri.sae.org/ When processes listed in another prime aerospace companys Approved Processor List, (i.e., Boeing D1-4426, Lockheed Martin QCS-001, etc.), are required by drawing, another specification, or purchase order, the supplier shall ensure that the processing source for these processes, including those performed in house by the supplier, are approved prior to any processing of hardware.

http://www.pri.sae.org/


Page 35 of 43

The ASPL, D1-4426 and QCS-001 are available on OASIS: https://oasis.northgrum.com/ The processor may use a later revision of a process specification shown on OASIS, provided the following requirements are met: 1) There are no Northrop Grumman-initiated engineering orders associated with the process

specification that the author of the specification has not incorporated in the latest revision. 2) There is no cost or schedule impact to deliverable hardware under contract. If an impact does

exist as a result of using a later process specification revision than that shown on OASIS, the supplier shall contact the buyer for disposition instructions.

Note: Suppliers with Design authority may approve their own sub tier process source(s) to their process specifications. This authority does not extend to other Primes process specifications, such as Boeing or Lockheed Martin. However, they are encouraged to subscribe to NADCAP by August 2003. Subcontracted processes of components of Supplier design must be performed by supplier-approved facilities whose capabilities and performance are supported by objective evidence of control such as: surveys and/or test results. A listing of all facilities being used must be available for review by Northrop Grumman which reserves the right of disapproval of those facilities not considered satisfactory. The suppliers shall not substitute their own process specification for the Northrop Grumman or customer process specification without prior written approval from Northrop Grumman Engineering.

The ASPL is organized by process type rather than by process specification. This listing of the ASPL indicates a Northrop Grumman approval of processor's capability to perform the process as required by the process specification. Listing in the ASPL does not assure or imply that the work performed by the ASPL processor is acceptable, nor does it compel the listed processor to accept the work. It is the responsibility of the Supplier and/or the processor to review, perform, inspect and certify the processes specification as required by the purchase order. Since many specifications call out multiple alloys, grades, types, classifications and conditions for materials, it is also the supplier and/or the processors responsibility to assure that you are approved for and capable of performing requested processing prior to any actual processing. Any departure from specification requirement requires the prior written approval of the Northrop Grumman engineering group responsible for the specification. The ASPL processors tier shall also comply with the Northrop Grumman Program unique requirements such as submission of test coupon, written approval of the processor's detail procedure, use of specific chemicals and/or concentration, and witnessing of first part processing and etc., when required by the process specification.


Page 36 of 43

QR # QC5107 Manufacturing Plan Submittals for Critical and Designated Parts (Northrop Grumman) New - 08/26/04 Parts designated or described as Fracture Critical, Fracture Critical Traceable, Fatigue Critical, Durability Critical, Maintenance Critical, or F-35 Critical Parts requiring traceability by engineering drawings, specifications or purchase order configuration, require submittal of the manufacturing plan to GKN at least forty five (45) days prior to start of production. The manufacturing plan shall contain sequential fabrication, processing, processor name, and inspection steps, in the order required by the applicable process specification(s) and/or engineering drawing(s). Upon approval of suppliers manufacturing plan, the supplier shall control all manufacturing, processing, testing and inspections as stated in the approved plan. No deviations, including the selection of suppliers sub-tier suppliers/processors, is permitted without GKN prior knowledge and written authorization. Manufacturing of product is not permitted until supplier has received GKN approvals. QR # QC5108 Tooling Requirements (Northrop Grumman) New - 08/26/04 The Northrop Grumman Supplier Tooling Manual delineates requirements for suppliers who have purchase orders that require manufacture, rework or use of Special Tooling (ST) and Special Test Equipment (STE). These requirements are applicable to all Northrop Grumman ST and STE fabricated and/or used in the manufacture of deliverable end items, unless specifically stated otherwise on the purchase order. Suppliers shall flow down requirements identified in these manuals to their sub-tier suppliers that fabricate or design tooling on their behalf. The Northrop Grumman Supplier Tooling Manual can be accessed on the Northrop Grumman Oasis website. https://oasis.northgrum.com/ Copies of other manuals/documents can be obtained by contacting the buyer. At a minimum, Special Tooling (supplier manufactured or Northrop Grumman furnished) used as a media of inspection must be delineated in the suppliers manufacturing plan at the applicable operation/sequence where the inspection occurs. Inspection media tooling must be controlled as part of the suppliers Periodic or Calibration system prior to use in production. Periodic tool inspection detailed requirements are covered in the Northrop Grumman Supplier Tooling Manual. QR # QC5109 Northrop Grumman Supplier Quality Assurance Requirements (SQAR) (Northrop Grumman) New - 09/16/15

Work to be accomplished in performance of this purchase order is directly related to a Northrop Grumman purchase order and must be accomplished in accordance with processes specified on this purchase order and Northrop Grumman SQAR (latest revision). Further information can be found at https://oasis.northgrum.com/contract/qualdocs.htm

https://oasis.northgrum.com/contract/qualdocs.htm


Page 37 of 43

QR # QC6000 HTF7000-Specific Quality Requirements New - 4/18/03 Revised 11/28/12 Obsolete: 6/1/16 QC6500 Work Related to Pratt and Whitney Purchase Order New 2/13/07

Work to be accomplished in performance of this purchase order is directly related to a Pratt and Whitney purchase order and must be accomplished in accordance with processes specified on this purchase order and Pratt and Whitney specification PWQA 6088 (latest revision). Further information can be found at http://www2.pratt-whitney.com/procurement/tphome.htm.

QC7000 Work Related to Lockheed Martin (Sikorsky CH53K) Purchase Order New 2/13/07 Revised 10/06/17 Work to be accomplished in performance of this purchase order is directly rel

MI 7.4-18 Quality Requirements Rev Q - gkn.com · Master document file contained in GKN Document...

Documents

Transcript of MI 7.4-18 Quality Requirements Rev Q - gkn.com · Master document file contained in GKN Document...