Menswear Measurement Generator Mg
-
Upload
tashathefirst -
Category
Documents
-
view
115 -
download
5
description
Transcript of Menswear Measurement Generator Mg
To unprotect sheet: PASSWORD (case sensetive)
YOUNG MEN'S SIZES (men under 35 with an athletic figure)
A size chart for overgarments, trousers, casual wear
standard body measurementsNo size 88 92 96 100 104
A CHEST 88 92 96 100 104B SEAT 90 94 98 102 106C WAIST 70 74 78 82 86D LOW WAIST (4cm below natural wai 73 77 81 85 89
E-F HALF BACK 18.5 19 19.5 20 20.5G-H NATURAL WAIST LENGTH 43.4 43.8 44.2 44.6 45G-I SCYE DEPTH 22 22.8 23.6 24.4 25.5J NECK SIZE 37 38 39 40 41
K-L SLEEVE LENGTH - one piece sleeve 63.6 64.2 64.8 65.4 66E-M SLEEVE LENGTH - two piece sleeve 79 80 81 82 83N-O INSIDE LEG 78 79 80 81 82P-Q BODY RISE 26.8 27.2 27.2 28 28.4
R CLOSE WRIST MEASUREMENT 16.4 16.8 17.2 17.6 18
A size chart for shirts
standard body measurementsNo size 88 92 96 100 104
J NECK (COLAR SIZE) 37 38 39 40 41A CHEST 88 92 96 100 104
G-I SCYE DEPTH 22 22.8 23.6 24.4 25.5G-H NATURAL WAIST LENGTH 43.4 43.8 44.2 44.6 45E-F HALF BACK 18.5 19 19.5 20 20.5
G-M SLEEVE LENGTH (for shirts) 86 87 88 89 89SHIRT LENGTH 76 78 80 80 80CUFF SIZE FOR SHIRTS 22 22.5 22.5 22.5 23
YOUNG MEN'S SIZES (men under 35 with an athletic figure)
A size chart for overgarments, trousers, casual wear
To unprotect sheet: PASSWORD (case sensetive)
CASUAL JACKET BLOCK 100CM CHEST
No Measurement basic
A CHEST 100
G-I SCYE DEPTH 24.4
G-H NATURAL WAIST LENGTH 44.6
J NECK SIZE 40
E-F HALF BACK 20
JACKET LENGTH 70
Vareis by jacket design
points calculation description
0 to 1 27.4 square across
0 to 2 45.6 square across
0 to 3 71.0 square across
2 to 4 21.0 square across
0 to 5 13.2 square out
0 to 6 6.6 square out
0 to 7 8.5 square up
7 to 8 2.0 draw in neck curve
1 to 9 22.0 square up to 10 and 11
11 to 12 2.0 square out
12 to 13 2.0 join 8 to 13 with a curved line
10 to 14 1.5cm
9 to 15 5.6
15 to 16 0.5
9 to 17 2.5 square down to 18 with a dotted line.
1 to 19 57.5 square up to 20 down to 21 on waistline, 22 on hem line
22 to 23 2.0 23 can be joined to any back style seam
1 to 24 33.8
24 to 25 5.9 half the measurement of point 9 to point 24 minus 1 cm. square d
24 to 27 2.5 Square up 2.5cm from point 24 mark front pitch (FP) See diagram
20 to 28 8.0 Join 28 to 11
20 to 29 9.0 draw in neck curve
28 to 30 you measure the measurement 8 to 13 inus 0.5cm. Join 30 to 27 with a dotted l
30 to 31 1.8 join 28 to 31
31 to 32 you measure measure point 31 to point 27 then divide by 3…. mark point 32...
A 1cm seam allowance is included in the block except where stated no seam allowance. There is no hem allowance. There is 1cm on the back shoulder.
(see Diagram
Draw in armhole, shape through points 13,14,16, 25, 27, 31 curve inwards 2cm at point 32. A one piece or two piece sleeve can be drafted for this block
DIAGRAM
To unprotect sheet: PASSWORD (case sensetive)
BASIC OVERGARMENT BLOCK Based on 100CM CHEST
CHEST 100
SCYE DEPTH 24.4
NATURAL WAIST LENGTH 44.6
NECK SIZE 40
HALF BACK 20
COAT OR JACKET LENGTH 100 VARIES WITH STYLE
points calc description
0 to 1 28.9 Square across
0 to 2 46.1 Square across
0 to 3 101.0 Square across
2 to 4 21.0 Square across
0 to 5 13.2 Square across
0 to 6 6.6 Square out
0 to 7 11.0 Square up
7 to 8 2.0 Draw in neck curve
1 to 9 23.0 Square up to 10 and 11
11 to 12 2.0 Square out
12 to 13 2.0 Join 8 to 13 with curved line
10 to 14 1.5
9 to 15 6.4
15 to 16 0.5
1 to 17 60.0 Square up to 18, down to 19 on hem line.
19 to 20 2.0 20 can be joined to any back style seam
1 to 21 35.6
17 to 22 12.2
9 to 23 7.3 Square down to 24
25 2.5 Square up from point 21 mark front pitch point (FP)
18 to 26 9.5 Join 26 to 11
18 to 27 9
26 to 28
28 to 29 1.5 join 29 to 2629 to 30 measure 29 to 25, then mark point 30 2/3rds from point 29
9 to 31 2.5 Square down to hem line.
Join 18 to 22 with a dotted line. Draw neck curve; construct a dart on the dotted line 1cm wide and 8cm long.
measure point 8 to 13 then minus 0.5cm. Join 28 to 25 with a dotted line
Draw in armhole shape through points 13, 14, 16, 23, 25, 29 curve inwards 1.75cm at point 30.
A one-piece sleeve or two-piece sleeve can be drafted for this block
To unprotect sheet: PASSWORD (case sensetive)
ONE PIECE SLEEVE BLOCK 100CM CHEST
Seven main measurements
Basic Total
SLEEVE LENGTH (one piece sleeve) 65.4 66.9
Scye measurment (armhole) 0 see diagram for how to measure scye
1cm has been added to the entirity of this pattern except at the hem.
Please study carefully, the diagram at the bottom of this page.
2.) Extend the "SCYE DEPTH LINE" of the body block beyond the center back line.
4.) Mark the underarm point as "0"
points calc description
1 to 2 0.0 Square across
1 to 3 0.0 Square across
FP to 6 The measurement 4-FP measured in a straight line, plus 2cm. Join FP to 6
6 to 7 The measurement 5-BP measured in a straight line plus 1.5cm, join 6 to 7
FP to 8 The measurement FP-0 measured in a curve plus 0.75cm; square down.
7 to 9
6 to 10 67.9 Square across to 11 & 1211 to 13 5.0 Join 8-13
12 to 14 5.0 Join 9-14
10 to 15 half measurement 10-14 15 to 16 1.0
9 to 7 Hollow the curve by 0.75cm
7 to 6 Raise the curve 1.5cm
6 to FP
FP to 8 Holow the curve 0.5cm
11 to 19 Half the measurement 8-11 plus 2.5cm; square across
1.) First, trace or copy and paste the top section (above waistline) of the "BASIC OVERGARMENT BLOCK" or the "BASIC CASUAL JACKET BLOCK" (depending on which you are drafting the sleeve for. Please refer to diagram at bottom of the page for more details.
3.) draw a vertical line through the front pitch point "FP". Where this line intersects the "SCYE DEPTH LINE" Mark point 1
Where the line crosses the back scye line of the body block mark back pitch point BP. Mark shoulder points 4 & 5.
The measurement BP-0 measured in a curve plus 0.75cm; square down. Square down from 6.
Join 10-14 with a curve. Square up 10cm from 16. Draw in outline of sleeve head.
Raise the curve 2cm at 17 (one third distance of 6-FP), touch the line at 18 (4cm from FP).
To unprotect sheet: PASSWORD (case sensetive)
TWO PIECE SLEEVE BLOCK 100CM CHEST
Seven main measurements
Basic Total
SLEEVE LENGTH (two piece sleeve) 82 83.5
Cuff size 29 33
Scye Measurement 0 see measuring a curve in diagram below
Half back 20
Body block markings
2.) Mark Points A & B on the traced body block, Mark C at underarm point.3.) Mark front pitch point (FP); mark D at the base of the line from FP4.) Mark points 9 and 14; mark 14 back pitch (BP)
Sleeve: Top sleeve
points calc description
Mark point 0; square across, up and down.
0 to 1 2.5 FP
0 to 2 / The measurement 9 to BP on body block; square across
0 to 3 1.5 square across1 to 4 /
4 to 5 /
0 to 6 2.0 Square down with a dotted line.7 / Midway between 5 and 44 to 8 /
5 to 9 1.5
9 to 10 61.0
10 to 11 / Half measurement 1-10; square across10 to 12 3.5 Square across12 to 13 18.5
10 to 14 2.0
/
15 to 16 3.0 Join 5-13 curving the line through point 16.
Sleeve: Under sleeve
0 to 17 2.017 to 18 0.5 Square down with a dotted line.
1cm has been added to the entirity of this pattern except at the hem. Please study carefully, the diagram at the bottom of this page.
1.) First, trace or copy and paste the top section (above waistline) of the "BASIC OVERGARMENT BLOCK" or the "BASIC CASUAL JACKET BLOCK" (depending on which you are drafting the sleeve for. Please refer to diagram at bottom of the page for more details.
The measurement A to FP measured in a staright line, plus 2cm; join 1 to 4
The Measurement B to BP measured in a straight line, plus 1.25cm; join 4 to 5
1/3rd measurement 4 to 1. Draw in sleeve head through points 5, 4, 1, 6 as shown in diagram
Join 13-10 and 10-14. Join 6-14; curve line inwards 1.5cm at elbow line. Join 5-13 with dotted line; mark 15 on elbow line.
10 to 19 2.0 Join 18-19; curve line inwards 1.5cm at elbow line.0 to 20 / The measurement C-D on body block plus 2cm20 to 21 0.5
21 to 22 /
23 / Midway between 21 and 22.23 to 24 2.0 Draw a curved line through points 22, 24, 21, 18.
22 to 25 1.5
26
The measurement BP-C measured in a curve plus 0.5cm (21-22 is measured straight to touch the line from 2-5.)
Midway between 15 and 16; join 25 to 13 with a curved line touching point 26. Extend back seam line 0.5cm above 25 to 27. Extend underarm seam line 0.75cm above 22 to 28. Join 27 to 28.
To unprotect sheet: PASSWORD (case sensetive)
CLASSIC SHIRT BLOCK 100CM CHEST
Seven main measurements
Basic
NECK SCYE 40
CHEST 100
SCYE DEPTH 24.4
NATURAL WAIST LENGTH 44.6
HALF BACK 20
SLEEVE LENGTH FOR SHIRTS 89
SHIRT LENGTH 80
CUFF SIZE 23
BODY SECTON
points calc description
MARK POINT 0 AND SQUARE BOTH WAYS
0 to 1 28.4 Square across
0 to 2 47.6 Square across
0 to 3 97 Square across
1 to 4 62 Square up to 5 and down to 6 on hem line
0 to 7 7.5 Squareup
7 to 8 4.5 draw in neck curve
0 to 9 7.68 Square out
9 to 10 24 Square down to 11 on scye depth line & up to 12
12 to 13 0.75 Join 8 to 13 with slight curve
10 to 14 10
10 to 15 0.75 join 14 to 15 with slight curve
1 to 16 31.5 Square down to 17 & 18
5 to 19 4.5 Square out
19 to 20 7 Square across
19 to 21 5.5 Draw in neck curve
10 to 22 1.5 Square out
20 to 23
1 to 24 37.833333
24 to 25 Square up 3cm from 24; join 23 to 25
23 to 26 Half the measurement of 23 to 25
Draw in armhole shape through points 13, 10, 16, 25, 23 curve inwards 1cm at 26.
21 to 27 1.5 Button stand square down
27 to 28 3.5cm facing; square down; shape top edge at neckline
17 to 29 2
17 to 30 2
18 to 31 20 Square across
A 1CM SEAM ALLOWANCE IS INCLUDED IN THE ENTIRE BLOCK EXCEPT FOR THE HEM ON ALL PATTERNS REMEMBER THAT!
The measurment 8 to 13 plus 0.5cm; join 20 to 23 with slightly curved line.
31 to 32 1
31 to 33 1 Draw in side seams
34 Midway 6 to 18 Square up
35 Midway 3 to 18
34 to 36 4 Square across to front edge
SLEEVE SECTION
ARMHOLE SCYE MEASUREMENT 54
points calc description
SQUARE DOWN FROM 0
0 to 1 13.5 Square across
0 to 2 92.0 Minus cuff depth and yoke width (0-13); square across1 to 3 39.3 Square across
0 to 4 27.0 Square down to 5
0 to 6 27.0 Square down to 7
Divide 0-4 into 4 sections mark points; 8, 9, 10.
Divide 0-6 into four sections mark points; 11, 12, 13.
5 to 14 7.8
7 to 15 7.8
5 to 16 3.9 Join 4 to 16.
7 to 17 3.9 Join 6 to17 draw in underarm seams as shown
2 to18 7.8 Square up 15cm to 19.
18 to 20 1.0 join 2 to 14 with a curve.
CUFF SECTION
CUFF LENGTH: use the cuff size measurement (top of page) and add 4cm.
Round off bottom edge (hem) of cuff. See diagram for further details.
COLLAR SECTION
Draw shaped curves as shown from 33 to 35 and 32 to 36. If pleats are required at the back yoke line, 9-37 is 2cm; square down.
Measure the armhole from from back shoulder point through side seams and to front shoulder point see diagram B below for details. You might have to print off the armhole to do this.
Please note the measurements below will not work unles the "ARMHOLE SCYE MEASUREMENT" Box is not entered (the default here is based on 100cm chest).
Draw in sleeve head; join 4-8, raise 1cm at 9, 2cm at 10, touch point 0, raise 1cm at 11, touch point 12, hollow 1cm at 13, join to 6.
CUFF DEPTH: Choose your cuff depth based on your own design idea. Then add 2cm.
points calc description
1A BASIC SHIRT COLLAR (see diagram)
1 to 2 20 4
2 to 3 3.75 3
1 to 4 15
1 to 5 9 Square across
1 to 6 4.5 Square across to 7 and 8
8 to 9 1 Join 3-9. 3-10 and 9-11 are 0.75cm. 1-12 is 0.5cm
1 to 12
1B SHIRT COLLAR WITH STAND (see diagram)
First copy & paste or Trace basic shirt collar outline
1C SHAPED SHIRT COLLAR WITH STAND (see diagram)
First copy & paste or Trace Shirt collar with stand
Divide 12-4 into four sections.
Shape stand and collar as diagram C
Add seam allowance for lines 6-14 and 6-15.
Collar depth (alter if you wish)
Stand depth (alter if you wish)
13 Is midway between 6 and 7; 7-14 and 11-15 are 1cm; join 13 to 15 with a curve. Join 14-16 at collar point. Separate collar and stand. Add seam allowance to lines 6-14 and 6-15.