Mechanical characteristics - Servis Elfo
8
Transcript of Mechanical characteristics - Servis Elfo
Luxtella street luminaires are technical luminaires that are designed to fulfil the most demanding lighting calculation scenes like S, ME and CE classes with different adaptation to local lighting standards.
TECHNICAL DATA
Mechanical characteristics
ź 220 - 240 V (50 - 60 Hz) inputź 110 - 277 V input voltage range
upon requestź Power factor at full load more than
0,95
ź Total harmonic distortion (THD) ≤8 %
ź Up to 94 % driver efficiency at full load with the Philips Xitanium LED driver
ź Dimming options: Lumistep, Line switch, DALI, 1 - 10 V and Dynadimmer (autonomous dimming) upon request
ź 6kV differential mode and 8 kV common mode standard surge protection. 10 kV surge protection upon request
ź Protection class I or II
ź Housing made of die cast aluminiumź Top pole or side entry. As a standard equipped
with a 60 mm pole connector, 76 mm also available
ź Possibility to change the inclination from -15° up to +15° in increments of 5°
ź As a standard equipped with a 0,5 m connecting cable, longer cable or without cable upon request
ź All screws are made of stainless steelź All gaskets are made of ozone and UV
resistant silicone for IP66 protectionź Certified for IK10ź Tool - less openingź Tempered cover glass 4 mm
Electrical characteristics
Luxtella street luminaires are technical luminaires that are designed to fulfil the most demanding lighting calculation scenes like S, ME and CE classes with different adaptation to local lighting standards.
TECHNICAL DATA
Mechanical characteristics
ź 220 - 240 V (50 - 60 Hz) inputź 110 - 277 V input voltage range
upon requestź Power factor at full load more than
0,95
ź Total harmonic distortion (THD) ≤8 %
ź Up to 94 % driver efficiency at full load with the Philips Xitanium LED driver
ź Dimming options: Lumistep, Line switch, DALI, 1 - 10 V and Dynadimmer (autonomous dimming) upon request
ź 6kV differential mode and 8 kV common mode standard surge protection. 10 kV surge protection upon request
ź Protection class I or II
ź Housing made of die cast aluminiumź Top pole or side entry. As a standard equipped
with a 60 mm pole connector, 76 mm also available
ź Possibility to change the inclination from -15° up to +15° in increments of 5°
ź As a standard equipped with a 0,5 m connecting cable, longer cable or without cable upon request
ź All screws are made of stainless steelź All gaskets are made of ozone and UV
resistant silicone for IP66 protectionź Certified for IK10ź Tool - less openingź Tempered cover glass 4 mm
Electrical characteristics
OPTICAL DATA
Optical characteristics• As a standard we use PMMA that is 100 % UV resistant which prevents
yellowing over the entire life time of the lenses
• Photometric LDT files are available upon request
Please send us your specific road situation and we will advise you on the right lamp to use based on our lighting calculations.
We use highly efficient & reliable Cree LEDs which ensure long term operation for the l i fetime of the
luminaire and highest lm/w efficiency in the industry. In the spreadsheet below the total – system W is stated. The below power (W) are a result in the working mode of the lamp (app. 1.5h after a lamp has been turned on). The below lumens are LED lumens. The system lumen and light distribution is available for each optic in LDT files. Different colour temperatures are available upon request. The below results in the table are written for 4000 K and 3000 K. (average results).
Upon request, we can also supply Luxtella with a different driving current.
LEDs
No. LEDs Current 4000K 3000K Power
400 mA 1600 1550 11 W
600 mA 2250 2150 16 W
800 mA 2850 2750 22 W
1000 mA 3400 3250 28 W
700 mA 3800 3600 27 W
12 LED 800 mA 4250 4050 31 W
900 mA 4650 4450 35 W
1000 mA 5050 4800 40 W
600 mA 6700 6350 45 W
700 mA 7600 7250 53 W
800 mA 8450 8050 60 W
900 mA 9250 8800 68 W
1000 mA 10000 9500 76W
700 mA 11300 10750 78 W
800 mA 12550 11950 89 W
900 mA 13700 13050 101 W
1000 mA 14800 14100 113 W
Cree XPG-3
8 LED
24 LED
36 LED
Optic A
Optic G
Optic C
Optic N
Optic L
Optimised for ME and S road classes and narrow roads (IESNA TYPE II). Pole height 4 – 6 m, pole spacing from 20 – 30 m (S classes), and height from 7 – 12 m, spacing from 30 – 40 m (ME classes).
Optimised for ME road classes and wider roads (IESNA TYPE III). Pole height from 7 – 12 m, pole spacing from 25 – 45 m.
Optimised for S road lighting classes with narrow roads (IESNA TYPE II/III) Pole height from 4 – 8 m, pole spacing from 25 – 45 m.
Wide beam optics (IESNA TYPE I) optimised for long pole distances, pedestrian & bike paths. Pole height from 4 – 9 m, pole spacing from 30 – 55 m.
Forward-throw beam optics (IESNA TYPE IV) optimised for wide outdoor areas and parking lots. Pole height from 6 – 12 m. pole spacing from 15 – 25 m.
Upon reuest, we
OPTICAL DATA
Optical characteristics• As a standard we use PMMA that is 100 % UV resistant which prevents
yellowing over the entire life time of the lenses
• Photometric LDT files are available upon request
Please send us your specific road situation and we will advise you on the right lamp to use based on our lighting calculations.
We use highly efficient & reliable Cree LEDs which ensure long term operation for the l i fetime of the
luminaire and highest lm/w efficiency in the industry. In the spreadsheet below the total – system W is stated. The below power (W) are a result in the working mode of the lamp (app. 1.5h after a lamp has been turned on). The below lumens are LED lumens. The system lumen and light distribution is available for each optic in LDT files. Different colour temperatures are available upon request. The below results in the table are written for 4000 K and 3000 K. (average results).
Upon request, we can also supply Luxtella with a different driving current.
LEDs
No. LEDs Current 4000K 3000K Power
400 mA 1600 1550 11 W
600 mA 2250 2150 16 W
800 mA 2850 2750 22 W
1000 mA 3400 3250 28 W
700 mA 3800 3600 27 W
12 LED 800 mA 4250 4050 31 W
900 mA 4650 4450 35 W
1000 mA 5050 4800 40 W
600 mA 6700 6350 45 W
700 mA 7600 7250 53 W
800 mA 8450 8050 60 W
900 mA 9250 8800 68 W
1000 mA 10000 9500 76W
700 mA 11300 10750 78 W
800 mA 12550 11950 89 W
900 mA 13700 13050 101 W
1000 mA 14800 14100 113 W
Cree XPG-3
8 LED
24 LED
36 LED
Optic A
Optic G
Optic C
Optic N
Optic L
Optimised for ME and S road classes and narrow roads (IESNA TYPE II). Pole height 4 – 6 m, pole spacing from 20 – 30 m (S classes), and height from 7 – 12 m, spacing from 30 – 40 m (ME classes).
Optimised for ME road classes and wider roads (IESNA TYPE III). Pole height from 7 – 12 m, pole spacing from 25 – 45 m.
Optimised for S road lighting classes with narrow roads (IESNA TYPE II/III) Pole height from 4 – 8 m, pole spacing from 25 – 45 m.
Wide beam optics (IESNA TYPE I) optimised for long pole distances, pedestrian & bike paths. Pole height from 4 – 9 m, pole spacing from 30 – 55 m.
Forward-throw beam optics (IESNA TYPE IV) optimised for wide outdoor areas and parking lots. Pole height from 6 – 12 m. pole spacing from 15 – 25 m.
Upon reuest, we
In addition, other features are available upon request (for example:
NEMA sockets) consult with your sales manager for the correct code!
The manufacturer reserves all rights to make changes in the materials and components used in its products. All data is subject to change without prior notice.
MECHANICAL DATA
8, 12, 24 or 36 LED lamp
Operating temperature from -40°C up to 55°C
Our standard warranty is 5 years but the warranty may be
extended for up to 10 years
Gross weight: 8,2 kgNet weight: 7,2 kg
2Wind area: 0,035 mBox dimensions: 71 x 35 x 10 cmFull euro pallet dimensions: 48 units: 80 x 120 x 150 cm
11
3
324
93
621
77
SURGEPROTECTION
NO INDICATION8 kV protection
P10 kV protection
L O
PROTECTIONCLASS
LED TYPE NUMBER OF LEDS
OXPG 3-4000 K
PXPG 3-6500 K
TXPG 3-3000 K
mA
35350 mA
40400 mA
45450 mA
50500 mA
60600 mA
70700 mA
80800 mA
90900 mA
001000 mA
REGULATION
RNo regulation
ADyna dimmer
OLumi step 6 h
KLumi step 8 h
FLine switch positive
MLine switch negative
DDALI
X1-10 V
LENGTH OFCABLE
NOINDICATION
0,5 meters
00 meter
1 meters
1212 meters
8 LED
12 LED
24 LED
36 LED
OPTICS
AUniversal
S class
C
GME class
L
Long pole dist. N
Forward-thrown
1protection class I
2protection class II
1
3 meters3
.........
CODE CONFIGURATOR
In addition, other features are available upon request (for example:
NEMA sockets) consult with your sales manager for the correct code!
The manufacturer reserves all rights to make changes in the materials and components used in its products. All data is subject to change without prior notice.
MECHANICAL DATA
8, 12, 24 or 36 LED lamp
Operating temperature from -40°C up to 55°C
Our standard warranty is 5 years but the warranty may be
extended for up to 10 years
Gross weight: 8,2 kgNet weight: 7,2 kg
2Wind area: 0,035 mBox dimensions: 71 x 35 x 10 cmFull euro pallet dimensions: 48 units: 80 x 120 x 150 cm
11
3
324
93
621
77
SURGEPROTECTION
NO INDICATION8 kV protection
P10 kV protection
L O
PROTECTIONCLASS
LED TYPE NUMBER OF LEDS
OXPG 3-4000 K
PXPG 3-6500 K
TXPG 3-3000 K
mA
35350 mA
40400 mA
45450 mA
50500 mA
60600 mA
70700 mA
80800 mA
90900 mA
001000 mA
REGULATION
RNo regulation
ADyna dimmer
OLumi step 6 h
KLumi step 8 h
FLine switch positive
MLine switch negative
DDALI
X1-10 V
LENGTH OFCABLE
NOINDICATION
0,5 meters
00 meter
1 meters
1212 meters
8 LED
12 LED
24 LED
36 LED
OPTICS
AUniversal
S class
C
GME class
L
Long pole dist. N
Forward-thrown
1protection class I
2protection class II
1
3 meters3
.........
CODE CONFIGURATOR
Luxtella is the brand name of luminaires produced by
Address Contact info web Info
Le-tehnika d.o.o.Šuceva 27, 4000 Kranj, Slovenia, EUROPE
Tel: + 386 4 20 20 246Fax: + 386 4 20 42 122
WWW.LUXTELLA.COM
Updated: April 2017
