Layout & Measuring

Layout & M

easuring

88 Tape Measures

91 Rules & Squares

95 Levels

97 Plumb Bobs / Stamps

98 Punches / Marking

100 Precision Measuring

107 Precision Layout and Measuring

Items may not be exactly as illustrated, Specifications may change without notice.88

Tape Measures

"AST" Measuring Tapes xYellow-black rubberized case xEasy to read red and black markings xSlide-down bar locks tape in any position xUnbreakable end hook xRemovable belt clip

SKU Description

T001 688AST 3/4" x 5M / 16' M/E

T001 689 1" x 5M / 16' M/E

T001 691AST 1" x 7.5M / 25' M/E

T001 696AST 1" x 9M / 30' M/E

FatMax® Tape

x11' tape standout x1-1/4" wide blade for easy readability xBladeArmor™ coating on the first 4" maximizes durability of hook end xMylar® polyester film extends life of entire blade xHigh-impact ABS case with rubber over mold is jobsite tough xTop-forward blade lock makes locking and unlocking a cinch x16" and 19.2" stud center markings simplify framing jobs xCushion grip provides comfortable, slip-resistant hold xSpecially designed hook grabs on side, top or bottom for versatility xBlade Length: 8m/26'

33-726

Stanley® Tape Rule (cm & in Graduation)

x7' standout (1" Blades" xHigh-contrast blade for easy readability xHigh-impact, high-visibility yellow case stands x16" Stud markings

SKU Description

30-496 3/4" x 16' / 5M

30-456 1" x 26' / 8M

Tape Measures

xRubber comfort grip xNylon coated steel blade xCo-molded rubber brake x3 Blade stops

SKU Description

T2215 1" x 16' / 5M

T2225 1" x 25' / 7.5M

T2230 1" x 25'

T2231 1-1/4" x 25' / 7.5M Wide Tape

Long Series Tape Measures

xRubber comfort grip xNylon coated steel blade x3:1 Gear ratio for quicker rewinding

SKU Description

T2240 1/2" x 50' / 15M

T2245 1/2" x 100' / 30M

Items may not be exactly as illustrated, Specifications may change without notice. 89

Tape Measures

Hi-Viz® Universal Lightweight Tapes xHigh impact polystyrene Hi-Viz ® orange case xYellow clad blade .005"/0.13mm thick xEasy wind nylon drum xEasy-to-read black and red markings xHook ring is retained neatly in the contoured mouth of the case xRemovable belt clip xHas a 2-sided end hook for use with either scale

SKU Description

HV15CME 3/8" x 50' / 15M

HV30CME 3/8" x 100' / 30M

Hi-Viz® Orange Speedwinder® Steel Tapes

x Impact-resistant, attractive, self-standing case xHeavy duty yellow clad blade protected by an abrasion resistant coating xExtends, rewinds in less time than conventional long steel tapes xEasy-to-read bold black markings

SKU Description

HYT15CME 3/8" x 50' / 15M

HYT30CME 3/8" x 100' / 30M

HYT50CME 3/8" x 164' / 50M

1/4" X 6' Executive® Diameter Pocket Tape

xDesigned for measuring diameters of pipe, cable, tire, and so on xPolished chrome case xZero falls in the same place on each side of the blade xConversion from diameter to circumference, simply turn the blade xShows diameter inches to 1/64ths xEasy-to-read bold graduations on yellow background xSpring action returns blade to case

W606PD

Series 1000 Tape Measures xLightweight, high strength black or orange finished case xFits easily into most tape holsters xBright yellow blade has clear easy-to-read numerals xToggle lock positioned for convenient operation, holds blade securely xVirtually unbreakable Quad Hook xCushioned blade return xRemovable belt clip

SKU Description Color

1048CME 1" x 26' / 8M Black

1038CME 3/4" x 26' / 8M Black

1035CME 3/4" x 16' / 5M Black

HV1049CME 1" x 30' / 9M Orange

HV1048CME 1" x 26' / 8M Orange

HV1035CME 3/4" x 16' / 5M Orange

HV1038CME 3/4" x 26' / 8M Orange

Series 2000 Tape Measures xLightweight, high strength chrome finished case xFits easily into most tape holsters xBright yellow blade has clear easy-to-read numerals xToggle lock positioned for convenient operation, holds blade securely xVirtually unbreakable Quad Hook xCushioned blade return xRemovable belt clip

SKU Description

2049CME 1" x 30' / 9M

2048CME 1" x 26' / 8M

2035CME 3/4" x 16' / 5M

Quick Read Tape Measures xGraduations printed in fractions and decimal equivalents xRounded blue case fits your hand for comfort xPositive toggle lock holds blade securely at any length xSelf-compensating end hook for inside and outside measurements xDurable ABS case withstands rugged use on the job site xBuilt in bumper reduces shock when blade is retracted

SKU Description

QR1312 3/4" x 12'

QR1316 3/4" x 16'

QR1425 1" x 25'

Tape Measures

Hi-Viz® Orange Fiberglass Linear Tapes xLine does not collect dirt in case xLightweight open reel is easy to handle and rewind xHi-Viz ® orange case

SKU Description

1703 1/2" x 50'

1706 1/2" x 100'

HY1715CME 1/2" x 50' / 15M

HY1730CME 1/2" x 100' / 30M

HY1750CME 1/2" x 164' / 50M

1708 1/2" x 200'

HY1760CME 1/2" x 200' / 60M

HY17100CME 1/2" x 328' / 100M

Open Reel Tape Measures xHeavy duty ABS case xPVC coated fiberglass tape for easy cleaning xTwo sided tape features Imperial on one side, Metric on the other xTape can be reversed to show either scale up x0 Point inside ring xRubber grip handle xFoldable handle for fast rewinding

SKU Description

T2250 1/2" x 165' / 50M

T2255 1/2" x 330' / 100M

1703HY1760CME

Measuring Wheels xMeasure as fast as you can walk xWheel calibrated to counter - accurate for estimated measurements xLarge wheel model ideal for uneven terrain xAlso suitable for long indoor measurements xManufacturing plant layout, outdoor measurements on firm smooth surfaces xRetractable handle adjusts for comfortable measurements

SKU Description

MW38 Feet

MW38M Metric

90 Items may not be exactly as illustrated, Specifications may change without notice.


Rules & Squares

Metric and English Wood Rule Red End®

xBlade Width: 5/8 in./16 mm xBlade Length: 6 ft./1.8 m xMarked both sides, reading left to right on both sides xGraduated in millimeters with centimeter, meter markings on metric side xEnglish side is marked to 1/16ths

062CME

Aluminum Straight Edge Rules

xParallel, accurate, flexible rules are made of anodized aluminum. xEdges are smooth, square and straight. xRules lie flat, resist bending and feature large, easy-to-read numbers. xASE Series: Graduations 1/8" on one edge, 1/16" on the other xAR Series: Graduations 1/8" on one edge, 1/16" on the other, Ruled two sides xASME Series: Centimeter and millimeter graduations on either edge xMS-2 Series: Graduations are in 1 mm (with mm conversion table) on one side; 1/8" and 1 mm graduations on the other. Ruled two sides.

SKU Series Length Thickness Width

36090 ASE 24" .081" 2"

36091 ASE 36" .081" 2"

36092 ASE 48" .125" 2"

36093 ASE 60" .125" 2"

36094 ASE 72" .125" 2"

36095 ASE 96" .125" 2"

36101 AR 12" .075" 1-1/8"

36102 AR 18" .075" 1-1/8"

36103 AR 24" .075" 1-1/8"

36104 AR 36" .075" 1-1/8"

36097 AMSE 500 mm 2 mm 50 mm

36098 AMSE 1000 mm 3 mm 50 mm

36099 AMSE 1500 mm 3 mm 50 mm

36100 AMSE 2000 mm 3 mm 50 mm

36107 MS-2 1 m 1.9 mm 30 mm

Stainless Pocket Clip Rule

xStainless steel blade will not corrode xEtched increments of 1/64" and mm xConversion table on back of blade xPocket clip for convenient storage

40-0555

36" Aluminum Yardstick

xDurable 1-1/8" wide extruded aluminum xScreened thermal bonded black graduations in 1/8" and 1/16" increments xBold, easy to read graduations and numbers xClear protective anodized finish

40-0554

Aluminum Rules

xDurable 1-1/8" wide extruded aluminum xScreened thermal bonded black graduations in 1/8" and 1/16" increments xBold, easy to read graduations and numbers xClear protective anodized finish

SKU Description

40-0556 12" Aluminum Ruler - 1/8" & 1/16"

40-0557 18" Aluminum Ruler - 1/8" & 1/16"

40-0558 24" Aluminum Ruler - 1/8" & 1/16"


Rules & Squares

Steel Straight Edges xThese straight edges are precision ground and nicely finished to rigid Starrett standards. xThey are unexcelled for drawing or scribing straight lines and checking surfaces for straightness. xTheir thickness and design permit them to retain shape and accuracy, but still be portable and easy to handle. xThe No. 380 Series are not beveled or graduated. xThe No. 385 Series are beveled one edge, but not graduated. xThe No. 387 Series have one edge that is both beveled and graduated in 1/32". xThe No. 380 and No. 385 Series in sizes 36 and longer are marked with arrows at two suspension points. If the straight edges are brought to the work and used on edge, they should be suspended at these two points to minimize deflection. xMost jobs involve the use of straight edges in the flat position – and it is in this position that we check most stringently.

Length Width x Thickness No. 380 Series No. 385 Series with Bevel

No. 387 Series with Bevel,

Graduations

12" / 300 mm 1-13/32" x 11/64" / 36 x 4.4 mm 51438 51455 51468

18" / 450 mm 1-13/32" x 11/64" / 36 x 4.4 mm 51439 51456 51469

24" / 600 mm 1-13/32" x 11/64" / 36 x 4.4 mm 51440 51457 51470

36" / 900 mm 2-13/32" x 7/32" / 60 x 5.5 mm 51441 51458 51471

48" / 1200 mm 2-13/32" x 7/32" / 60 x 5.5 mm 51442 51459 51472

72" / 1800 mm 3-5/32" x 9/32" / 80 x 7 mm 51444 51461

48" Adjust-A-Square Aluminum T-Square xExtruded aluminum 1/4" thick blade and head xClear protective anodized finish will not rust or corrode xScreened thermal-bonded black 1/16" graduations xLarge bold graduations and numbers for readability xHead adjusts to any angle xPrecision machined head and blade lock together for a perfect 90° angle xFolds flat for easy transportation

40-0500

48" Professional Aluminum Drywall T-Square

xUnique rivet assembly, permanently bonds head to blade xHead will stay square for life of product xExtruded aluminum 1/8" thick blade and head xClear protective anodized finish will not rust or corrode xScreened thermal-bonded black 1/8" graduations xLarge bold graduations and numbers for readability

40-0504

93Items may not be exactly as illustrated, Specifications may change without notice.

Rules & Squares

24" x 2" Steel Rafter/Roofing Square xHigh-quality hardened steel provides durability and long life xMarkings include Essex board measure, octagon scale, brace scale, and rafter table xDurable, embossed graduations and figures for easy reading xBuffed finish with a clear lacquer that resists rust xBody Length : 24" x 2 xFinish : Buffed xGraduation-Back : 1/16", 1/10", 1/12" xGraduation-Face : 1/16", 1/8 xTongue Length : 16" x 1-1/2

45-910

Steel Carpenter's Squares xHigh-quality hardened steel for durability and long life xEmbossed graduations for easy reading on face and back xReverse reading scale makes measuring more efficient xTreated with a clear, protective finish that resists rust

SKU Body Length

Finish Graduation-Back

Graduation-Face

Tongue Length

45-500 24" x 2" Buffed 1/8" 1/8" 16" x 1-1/2

45-912 12" x 1-1/2" Buffed 1/16" 1/16" 8" x 1"

439 Series Builders’ Combination Tool xThis versatile tool is invaluable for carpenters, builders, patternmakers, cabinetmakers and all mechanics. xCombines seven tool functions in one compact, practical unit. It is a rule, square, level, plumb, protractor, bevel and pitch-to-foot indicator. x It consists of a stock, 9" (230 mm) long, a hardened, machine-divided 1-1/2" (38 mm) wide blade in 18" or 24" lengths, and a protractor xOn one side the protractor is graduated from zero to 90º in both directions showing the direct and supplementary angles. The other side is graduated in 1/2" pitch increments from 0-12" per foot pitch. xThe stock has four levels which permits leveling or plumbing the work in relation to any angle or pitch xTool is ideal for laying out or cutting valleys or hips of different pitches, done as follows: Rotate the blade to the desired pitch, place the face of the stock against the work and draw a line. Then place the square end of the stock against the line and draw the complementary line. This gives the complementary angle automatically, without calculation. xBlade Graduations: 8ths, 16ths, 32nds, 64ths xHead Graduation Degrees: 0 - 90° xHead Graduation Pitch: 0 - 12" per ft.

SKU Blade Length

52110 18"

52111 24"


Rules & Squares

AM-2 Angle Meter xThis angle meter offers a fast, easy and inexpensive way to measure angles. xLarge, readable scale for accurate readings from 0-90º in any quadrant xMagnetic base frees hands when used on ferrous surfaces xMeasures any angle for pitch or slope xHandy rise, run, angle, and pitch information on back of tool

36080

Magnetic Angle Locator

xHigh-impact molded body xEasy-to-read increments from 0-90° in all four quadrants printed on durable acrylic lens xExtra strong ceramic magnet adheres to ferrous metal surfaces xV-Groove edge fits on pipe and conduit x Inch and metric graduations on edge

40-0220

Tri Square

x12" xEnglish / Metric xStainless steel blade xBuilt in scriber xEasy to read vial

T5500

Combination Squares

xDurably etched, hard-chrome-plated blades are rust resistant and made to last x12" square has precision-machined working surfaces for improved accuracy xBuilt-in scriber comes in handy for surface marking xEasy-to-read vial xHigh-visibility yellow, die-cast handle with brass hardware for durability

SKU Type Blade Length

Blade Width

Blade Graduations

46-028 English/Metric 12"(305 mm) 1"(25 mm) 1/16"

46-131 English 16"(406 mm) 1"(25 mm) 1/32", 1/16", 1/8"

Combination Set

xForged and Hardened Steel Heads and Center Head, Cast Iron Protractor Head: (The very best sets available) xWith reversible lock bolts, scriber, spirit level in both square head and protractor head, direct reading double 180º protractor scale, hardened steel, machine-divided blade. xForged and hardened heads and center heads, cast iron portractor head with smooth black finish. xBlade Size: 12" xNo. 4R – 8ths, 16ths, Quick Reading 32nds, 64ths

51542

Premium Quick Square® Layout Tool xDurable aluminum construction xBlack body with yellow graduations provides maximum readability in all light conditions xMultipurpose tool is ideal for use as a 0° to 90° protractor scale xWorks well as a saw guide xBase Length: 10-1/4" xRule Length: 6-7/8"

46-071

Levels

Machined Top-Read Aluminum Levels

xExtruded aluminum I-beam frame with black anodized finish. xComputer machined level edges. 360 degree reading acrylic yellow barrel vials. xScrew on high impact plastic covers with protective lenses. xLarge, patented, magnified top-read window. xShock-protecting end caps. xFrame dimensions: 1” x 2-1/4”.

SKU Length # of Vials

40-0050 24” 3

40-0053 36” 3

40-0054 48” 3

9" Magnetic Aluminum Torpedo Level

xStrong holding magnetic edge holds to ferrous metal surfaces xSuper strong 9" solid aluminum frame is Job Site Tough xV-Groove frame fits on pipe and conduit xSurroundView® vial surrounds enhance readability x3 vials read plumb, level and 45° xTop-read window for easy viewing

40-0209

Aluminum I-Beam Levels

SKU Size

T5805 24"

T5810 48"

T5813 72:

Torpedo Level

xAluminum x9" xMagnetic xLevel vial is top reading

T5800

Machinists Level

x12" Length xGround and graduated main vials. xCross test vial xPlumb vial xThese vials are adjustable to a positive setting and are housed in a satin finished brass tube with a friction-fit closing cover to prevent breakage. xThe base of the level features an involute groove running the length of the base, which provides a reliable seat for round work such as pipes or shafting. xWith the cross test vial, it is possible to simultaneously level in both directions. This prevents inaccuracies in the main vial reading caused by canting the level sidewise on round work. xVials have graduations that are approximately 80-90 seconds or .005 per foot (0.42mm per meter).

50443



Levels

Pro I-Beam Levels

xDurable I-beam construction made of aluminum xVials provide accuracy of 0.0015 in/in (1.5mm/m) xCenter top read for improved visibility xMagnetic versions have full length magnetic strip to allow for hands free operation on metal surfaces xPipe groove for use on rounded surfaces ( non-magnetic versions only) xLow profile, shock absorbing end caps

SKU Type Color Vials Hand Holes

Length

42-240 Yellow 3 (1 level, 2 Plumb) 0 24"(610 mm)

42-244 Magnetic Silver 3 (1 level, 1 Plumb, 1 45°) 0 24"(610 mm)


42-486 Magnetic Silver 3 (1 level, 1 Plumb, 1 45°) 2 48"(1219 mm)


42-789 Magnetic Silver 6 (3 level, 3 Plumb) 4 78"(1981 mm)

3-3/32" Aluminum Line Level

xAluminum construction is lightweight and durable xSpecial hang hooks grip line which enables level to slide freely for positioning xFlat base is ideal for surface leveling x360° vial for easy readability

42-287

9" Magnetic Cast Aluminum Torpedo Level

xDurable, heavy-duty, cast aluminum frame features large, top-read vial window xTinted 360° vials make reading easy on the eyes xPipe groove enables use on rounded surfaces xMagnetic strip allows hands-free operation on metal surfaces

42-465

Top Read Levels

xDurable I-beam construction made of aluminum xVials provide accuracy of 0.002 in/in (2mm/m) xCenter top read for improved visibility xLow profile, shock absorbing end caps

SKU Color Vials Hand Holes Length

42-074 Silver 3 (1 level, 1 Plumb, 1 45°) 1 24" / 610 mm

42-076 Silver 3 (1 level, 1 Plumb, 1 45°) 2 48" / 1219 mm

FatMax® Xtreme™ Magnetic Torpedo Level

xDie-cast aluminum body xSolid block vial provides accuracy of 0.0005in/in. (0.5mm/M) x180 degree rotating vial to duplicate angles xMagnified center vial for improved visibility xPipe groove for use on rounded surfaces xRare earth magnets for ultimate holding power xLifetime Accuracy Warranty

43-609


Plumb Bobs / Stamps

Plumb Bob Kit xChrome plated plumb bob xSlack adjuster x8' Nylon twine

P01 0650

Brass Plumb Bobs xHigh quality machined brass xLacquered for long life xRemovable hardened steel tip xTop unscrew for easy centered string installation

SKU Description

P01 0616 8 oz.

P01 0621 12 oz.

Brass Plumb Bobs

xPolished-lacquer, solid-brass construction is durable and rust resistant xReplaceable, hardened steel tip is long-lasting xScrew top simplifies attaching string to center of plumb xThru hole ensures easy tightening

SKU Description

47-969 4 oz.

47-973 8 oz.

47-974 16 oz.

Plumb Bob x8 oz. xChrome steel

T5700

Steel Hand Stamps

xFor hand held, hammer-struck applications. xCrowned striking and textured shanks. xPacked in durable plastic or metal storage containers. xLetter sets contain 27 pieces - A thru Z, plus ampersand (&). xNumber sets contain 9 pieces - 0 thru 8 (the 6 is used as a 9).

SKU Character Size Square Size Overall Length

Letter Sets34-20200 1/8" 1/4" 2-3/8"

34-20250 3/16" 5/16" 2-3/8"

34-20300 1/4" 3/8" 2-5/8"

34-20350 3/8" 1/2" 2-3/4"

34-20400 1/2" 5/8" 3"

Number Sets34-20541 1/8" 1/4" 2-3/8"

34-20561 3/16" 5/16" 2-3/8"

34-20581 1/4" 3/8" 2-5/8"

34-20601 3/8" 1/2" 2-3/4"

34-20621 1/2" 5/8" 3"

Letter & Number Sets34-20624 1/8" 1/4" 2-3/8"

34-20625 3/16" 5/16" 2-3/8"

34-20626 1/4" 3/8" 2-5/8"

34-20627 3/8" 1/2" 2-3/4"

Punches / Marking

Scriber xCarbide Tipped x6" Reach

K908

Scratch Awl xBlade Length: 4" xOverall Length: 7-3/4"

91425A

Automatic Center Punch x6"

T4998

565 Series Drive Pin Punch Set xWell proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. xEach punch has the size stamped on the head. xAll punches 4" / 100 mm long x Includes punch sizes: 1/16", 3/32", 1/8", 5/32", 3/16", 7/32", 1/4", 5/16"

52586

248 Series Drive Pin Punch Set xStarrett No. 248 Drive Pin Punches are extra-long, measuring 8" (200 mm). xThe bodies are 4-1/2" (115 mm) and the drive pin sections are 3-1/2" (90 mm) long. xThey are well-proportioned, hardened, properly tempered, and have a knurled grip. xThey are designed to withstand hard use and provide a most satisfactory punch for machine shop and motor service work. x Just the punch to follow long cotter pins and the like into holes without hindrance. x The diameters of the punches are slightly under the sizes listed below. x Includes punch sizes:1/8", 3/16", 1/4", 5/16", 3/8" in protective vinyl case.

51186



Punches / Marking

Hi-Visibility Marking Chalk xExterior use x Ideal for low light conditions and on dark surfaces xUse to show layout changes and corrections

SKU Size Color

64903 8 oz. Yellow

94905 8 oz. Orange

94907 8 oz. Green

65103 5 lb. Yellow

65105 5 lb. Orange

65106 5 lb. Green

Carpenter's Pencil xLong lasting xEasy sharpening xSmooth writing xRectagular xRed Color x12 Pack

P005602

Aluminum Chalk Reel xHeavy-duty case is constructed of durable aluminum alloy xSteel plated hook and large grip anchor ring provide better holding power xRetractable self-locking metal handle allows reel to be used as a plumb bob xTwisted cotton line holds more chalk for multiple line strikes xHolds approximately 2 oz. of chalk x100'

64110

Replacement Lines xNew anchor ring provided with each replacement line xTwisted polyester line holds more chalk for multiple line strikings

SKU Size

64550 50'

64610 100'

Standard Marking Chalk x Interior or exterior use xMarks are temporary xProvides great visibility

SKU Size Color

64901 8 oz. Blue

64904 8 oz. White

65101 5 lb. Blue

65104 5 lb. White

Permanent Marking Chalk xExterior use xVisible after weeks of weather exposure and jobsite wear

SKU Size Color

64902 8 oz. Red

64908 8 oz. Black

65102 5 lb. Red

2032160 5 lb. Black


Precis ion Measuring

Outside Micrometers xStarrett satin chrome finish – no glare –resists rust xAdvanced sleeve design with staggered lines and distinct figures for precise and easy readability xBalanced frame and thimble design insure easy handling xRing-type knurled lock nut for quick and sure locking xSmooth friction thimble for uniform pressure, the combination ratchet and speeder for uniform pressure and quicker adjustment, or a plain micrometer that depends on your own “feel” xGracefully designed tapered frame for use in narrow slots and tight place xRigid steel frame ribbed for extra strength on sizes through 6 (150mm) xExtremely hard and stable one-piece spindle (the heart of our accuracy) xMicro-lapped measuring faces xQuick and easy adjustment xStarrett workmanship

436.1 AnD 436.1 SERIES xThese are the most popular precision micrometers used by skilled workmen worldwide. xThey are accurate, rugged, and easy to use. xThe 0-6 sizes and 0-150mm sizes have rugged spindles and anvils sized at .250 (6.35mm) diameter.

SKU Range Graduation Description

67993 0-1" .001" Ratchet Stop, Lock Nut






68051 0-25 mm 0.001 mm Ratchet Stop, Lock Nut,Carbide Faces






224 / 224M SERIES InTERCHAnGABLE AnVIL xUnusual flexibility, plus a wide range of measurement makes the Starrett No. 224 series satin-chrome micrometers very popular in machine or automotive repair shops and for all applications requiring a versatile micrometer. xEach micrometer is equipped with a series of easily interchangeable anvils, thus providing the full range in steps of 1 or 25mm with a single micrometer. Suitable wrenches are furnished to make necessary adjustments. xThese larger sizes have .300 (7.6mm) anvil and spindle diameters for ease of use on larger work.

SKU Range Graduation No. 234 Standards Furnished

50770 0-4" .001" 1", 2", 3"

50772 2-6" .001" 2", 3", 4", 5"

50774 6-9" .001" 6", 7", 8"

50776 6-12" .001" 6", 7", 8", 9", 10", 11"

50771 0-100 mm 0.01 mm 25, 50, 75 mm

50773 50-150 mm 0.01 mm 50, 75, 100, 125 mm

50777 15-300 mm 0.01 mm 150, 175, 200, 225, 250, 275 mm



124 Series Solid-Rod Inside Micrometers xThese are the most popular inside micrometers because of their lightness, ease of use, and range. They are very useful for measuring inside diameters of cylinders and rings, measuring parallel surfaces, etc. xThe desired range is obtained by assembling rods and spacing collars to the micrometer head. Measuring rods are provided with a shoulder that is set accurately in the micrometer head and locked in position. When assembling rods to the A and B heads, the reading line on the micrometer head should be lined up with the marking on each rod (except for the 2-3 and the 50-75mm rods). xRod diameters are approximately 1/4 (6mm) on the A and B sizes, and approximately 11/32 (8.5mm) on the C size. Each rod has individual length adjustment for the anvil by means of special wrenches furnished. xMeasuring rods are solid and assembled on one side of the micrometer head xRods are insulated xEach rod marked with length xHardened and ground anvils on rods, adjustable for length. Head anvil is hardened and ground xQuick-reading figures – every thousandth numbered on inch reading tools xA 6-1/2 (165mm) long convenient handle is available to provide reach for use in deep holes. Handle screws into the micrometer head in place of the dummy screw, which is opposite a rod lock screw xCase included

SKU Range Movement of Screw

No. Measuring Rods

No. Spacing Collars

50542 2-8" 1/2" 6 One 1/2"

50546 2-12" 1/2" 10 One 1/2"

440 Series Depth Micrometers xThe depths of holes, slots, shoulders and projections can be measured to .001 or 0.01mm with these fine tools. xFurnished with a 2-1/2 (63.5mm) base and 1/8 (3.2mm) diameter measuring rods. xThe combination ratchet and speeder for uniform pressure and quicker adjustment xRing-type lock nut for quick and sure locking xWith Ratchet Stop, Lock Nut, in Case

SKU Range Graduation Base No. Rods

Rod Diameter

52115 0-3" .001" 2-1/2" 3 1/8"

52119 0-6" .001" 2-1/2" 6 1/8"

52123 0-9" .001" 2-1/2" 9 1/8"

52116 0-75 mm .01 mm 75 mm 3 3.2 mm

52120 0-150 mm .01 mm 75 mm 6 3.2 mm

52124 0-225 mm .01 mm 75 mm 9 3.2 mm



799 Series Electronic Calipers xLightweight, ergonomic design x Inch/millimeter conversion reads .0005" or 0.01 mm xEasy access to the single, long-life battery xLast measuring position retained when shut off xHardened stainless steel body for long life xFine adjustment thumb wheel xLock screw to hold the slide in position xResolution is .0005" (0.01 mm) xZero at any position xLarge easy-to-read LCD, .32" high characters xAutomatic shut-off after 5 minutes of non-use xLinear accuracy meets DIN862 x Integrated depth rod

SKU Range Description

67410 0-6" (150 mm) Caliper in Fitted Plastic Case



1202 Series Dial Calipers xSharp, clear dial graduations of .001 with .100 per revolution xSharp, black graduations on the satin finished bar, every .100 xKnife-edge contacts xThumb-operated fine adjustment roll xAdjustable bezel xLock screws for sliding jaw and dial bezel xCovered rack depth rod (4, 6 and 8" models) xHardened stainless steel bar, measuring surfaces, rack, gears and depth rod xPositive, spring-loaded double pinion anti-backlash control

SKU Range Description

68814 0-4" Caliper in Fitted Plastic Case




708 and 709 Series Dial Test Indicators With Dovetail Mounts xAngled head for better reading position xLarge 1-3/8" (35 mm) dial diameter xPrecision gear-driven design with smooth, jeweled movement xMeet or exceed ISO accuracy specification xFor extreme accuracy we recommend positioning the lever contact so that it is approximately 15º from being horizontal with the workpiece xThree dovetail positioning mounts work with existing test indicator accessories xContact point reverses automatically, always maintaining clockwise hand rotation xNarrow body for in-reach ability xSatin chrome finish for durability xWhite Dial xWithout attachments

SKU Graduation Range Dial Reading

Carbide Contact point

Length Ball Diam.

64212 .0001" .010" 0-5-0 13/16"(20 mm) .078"(2 mm)

64214 .0005" .030" 0-15-0 13/16"(20 mm) .078"(2 mm)



657AA Magnetic Base Indicator Holder xFor use with all Starrett Test, Back-Plunger, AGD, Dial and Miniature-Dial Indicators. xAlso accommodates similar indicators of other manufacturers. xA. No. 657P Magnetic Base: 1-15/16 x 1-5/8 x 1-7/8 (50 x 40 x 48mm). Push-button on/off switch for one-hand operation. Base has three precision ground magnetic contact points. Grips horizontally, vertically, and upside down. V-step holds base to arbors, shafts, etc. Base has extra 1/4-20 tapped hole on one side for mounting post. Black wrinkle finish on non-working surfaces. xB. No. 657G Upright Base Post: 3/8" (9.5mm) diameter x 7-7/16" (190mm) length overall. Starrett No. 57S and No. 58S Universal Snugs may also be used. xC. No. 657S Snug: Two 1/4" (6.3mm) diameter holes. Adapts Nos. 196, 650, and 651 Series Dial Indicators and No. 657Y Indicator Attachment to No. 657X Rod. xD. No. 657X Rod: 1/4 (6.3mm) diameter x 6 (150mm) long. Accommodates Starrett Nos. 708, 709, 811 and 711F Series Dial Test Indicators and No. 657S Sleeve. xE. No. 657Y Indicator Attachment: 1/4" (6.3mm) O.D. one end, other end threaded and fits lug backs of all AGD indicators (Starrett Series Nos. 81, 25, 655, 656) and Series No. 80 Miniature Indicators. xF. No. PT18724 Snug: 3/8" (9.5mm) diameter post hole. 1/4 (6.3mm) diameter gripping hole accommodates No. 657X Rod.

SKU Item Description

52743 Complete Magnetic Base with All Attachments – A, B, C, D, E, F

52757 A 657P Magnetic Base Only

52753 B 657G 7-7/16" Upright Base Post Only

52759 C 657S Snug with Two 1/4" (6.3 mm) Holes

52764 D 657X Rod

52765 E 657Y Indicator Attachment

50710 F PT18724 Snug Complete – 1/4" and 3/8" Holes

Flex-O-Post Indicator Holder with Magnetic Base 657T Series xFor use with all Starrett Test, Back-Plunger, AGD, Dial, and Miniature Dial Indicators. Also accommodates similar indicators of other manufacturers. The flexible post is an assembly of short tubular steel sections and precision ball joints, linked by an internal steel cable. It can be adjusted to any position and locked by turning a lever near the magnetic base. This makes it possible to use indicators in awkward places that are hard to reach with conventional holding devices. xAssembled to the magnetic base, the post has a vertical reach of approximately 15" (380mm) and a horizontal reach of approximately 10" (250mm). The indicator snug on the end of the post can be rotated through 360º and locked in any position. xThe base has three precision ground magnetic contact surfaces. Grips horizontally, vertically or upside down. V-step holds base to arbors, shafts, chucks.

52760



Universal Snug xAdapt various scribers and indicator shanks to rods and posts. xWith 1/4", 5/16" and 3/8" hole diameter

56613

25 Series AGD Group 2 Dial Indicators

xThese indicators have a shockless, hardened steel gear train and jewel bearings, except where noted. xThey are furnished with a lug-on-center back. xAntimagnetic mechanism is optional for all models. xSpecial nonshock mechanism is available

SKU Graduation Range Dial ReadingOne Rev Total

53223 .0001" .010" .025" 0-5-0

53232 .0005" .050" .125" 0-25-0

53295 .001" .100" 1.000" 0-100

Magnetic Back xThis magnetic back provides a quick and easy means of attaching any Starrett AGD indicator to flat, ferrous metal surfaces. xA real timesaver for machine, jig and fixture set up. xRequires no clamps, rods or snugs. xA special 5/16-24 threaded stud back is provided to replace the standard lug back. xThe powerful, permanent magnet is then attached to the threaded stud. xAnti-magnetic indicators are not required. xFits Starrett Nos. 25, 2600

56648

Swivel Post Snug with Dovetail Indicator Clamp

xWill fit over spindles and posts 3/32-1/4" (2.4-6.3mm). Can be used directly on our No. 252 Height Transfer Gage and our No. 657 Series Magnetic Base Holders. It is frequently used on the 1/4 (6.3mm) rod of the Snug and Rod Unit No. PT22430.

72440

154 Series Adjustable Parallels

x 3/8 – 2-1/4" (9.5-57mm) range xStarrett adjustable parallels provide a wide range of use in layout, gaging, inspection work and for setups on various machine tools. xTheir adjustable feature makes it possible to adjust them to exact size by micrometer measurement and also permits use in place of several solid-type parallels. xThese parallels are useful as gages in checking the size of slots and openings. xThey are also convenient for use in machine vises, for leveling or adjusting work on setups of milling and grinding machines, shapers, planers, drill presses and for many other applications. xParallels slide smoothly and can be easily adjusted. The smaller sizes A, B, and C, are locked by one screw while the larger sizes, D, E, and F, have two lock screws. xAll parallels are 9/32" (7mm) thick. xSet of 6

50586

Drill and Steel Wire Gage xHas 60 holes for gaging drills from No. 1 to 60 and each hole is marked with the number size and decimal equivalent of the drill that fits each hole. xBlack matte finish. xGage information is steel stamped on one side and white marked on the reverse side for quick, clear reading. xApproximate size, 5/64" thick, 1-1/2" wide and 5-1/2" long.

50676



“Yankee” Spring-Type Calipers and Dividers xMade from a high-grade steel and well finished. xThe legs are made of flat stock and are very durable. The fulcrum stud is hardened and has a smooth bearing surface. The bow spring, although flexible, is exceedingly strong to assure reliability. xQuick-adjusting automatic-closing spring nut is designed for making fast, positive adjustments. xThe threads of the nut firmly engage the screw at the slightest pressure from the leg. When the pressure is withdrawn, the nut automatically releases itself, sliding freely over the screw. This feature saves time in opening and closing.

Size and Approx. Capacity

Inside Calipers

Outside Calipers

Dividers

4" 100 mm 50335 50365 50377

6" 150 mm 50337 50367 50379

8" 200 mm 50339 50369 50381

12" 300 mm 50343 50373 50385

579 Series Self-Centering Telescoping Gages xHandles are rigidly attached to the contact plungers and are automatically self-centering. xTwo telescoping contacts. xConstant spring tension gives uniform contact pressure and both plungers are easily locked at any desired setting.

SKU Range Handle Length

52610 5/16 – 1/2" 8-13 mm 2-3/8" 60 mm

63192 5/16 – 1/2" 8-13 mm 8" 200 mm

63195 5/16 – 1/2" 8-13 mm 12" 300 mm

52611 1/2 – 3/4" 13-19 mm 2-3/8" 60 mm

63193 1/2 – 3/4" 13-19 mm 8" 200 mm

63196 1/2 – 3/4" 13-19 mm 12" 300 mm

52612 3/4 – 1-1/4" 19-32 mm 2-3/8" 60 mm

63194 3/4 – 1-1/4" 19-32 mm 8" 200 mm

63197 3/4 – 1-1/4" 19-32 mm 12" 300 mm

52613 1-1/4 – 2-1/8" 32-54 mm 2-3/8" 60 mm

67114 1-1/4 – 2-1/8" 32-54 mm 8" 200 mm

63198 1-1/4 – 2-1/8" 32-54 mm 12" 300 mm

52614 2-1/8 – 3-1/2" 54-89 mm 2-3/8" 60 mm

67115 2-1/8 – 3-1/2" 54-89 mm 8" 200 mm

63199 2-1/8 – 3-1/2" 54-89 mm 12" 300 mm

52615 3-1/2 – 6" 89-150 mm 3-1/4" 82 mm

67116 3-1/2 – 6" 89-150 mm 8" 200 mm

63200 3-1/2 – 6" 89-150 mm 12" 300 mm

52617 Set of 6, 52610, 52611, 52612, 52613, 52614, 52615 in case

Quick-adjusting spring

nut makes fast, accurate

settings.


Metric Screw Pitch Gage xNo. of Leaves: 28 xTPI Range: 0.25-2.50mm xThreads per Inch (TPI): 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55, 0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90, 1, 1.10, 1.20, 1.25, 1.30, 1.40, 1.50, 1.60, 1.70, 1.75, 1.80, 1.90, 2, 2.50 xWith Locking Device

50589

English Screw Pitch Gage xNo. of Leaves: 30 xTPI Range: 4–42 xThreads per Inch (TPI): 4, 4-1/2, 5, 5-1/2, 6, 7, 8, 9, 10, 11, 11-1/2, 12, 13, 14, 15, 16, 18, 20, 22, 24, 26, 27, 28, 30, 32, 34, 36, 38, 40, 42 xWith Locking Device and 11-1/2 and 27 Pipe Thread Pitches

50035

English Standard Wire Gage xNos. 1-36 (.300-.004") xThis gage is popular for gaging iron wire, hot and cold rolled sheet steel, and in some cases, sheet iron by the English Standard Wire system also known as Birmingham or Stubs. xGage has convenient decimal equivalents of each number on the reverse side. xSatin finish. xCarefully tested after hardening.

50678

25 Blade Master Feeler Gauge Set

xContains twenty-five short blades in holder. x Includes all short blade sizes .0015" thru .040" except .019". xBlades etched with both decimal size and metric equivalent.

J000AA

9-Blade Short Standard Feeler Gauge Set

xContains 9 short blades in holder xShort blades in sizes .003", .004", .005", .006", .008", .010", .012", .015" and .018", in No. 000C holder xBlades etched with both decimal size and metric equivalent

J000A

25 Blade Long Feeler Gauge Set

x1/2" wide by 12" long blades in steel blade holder. xSizes: .0015", .002", .003", .004", .005", .006", .007", .008", .009", .010", .011", .012", .013", .014", .015", .016", .017", .018", .019", .020", .021", .025", .027", .030", .040". xBlades etched with both decimal size and metric equivalent.

J000TL

Thickness Gage or “Feeler” Stock in Rolls xHandy 25' rolls 1/2" wide, in a compact, sturdy plastic rewindable dispenser case. xRewind feature permits retracting thinner feeler stock into the case, preventing damage xMade of the finest tempered steel xMarked every 6" with a line, thickness in thousandths of an inch or in hundredths of a mm xCase provides the ability to snip off the desired length without any waste

SKU Thickness

52796 .001"

52797 .0015"

52798 .002"

52799 .0025"

52800 .003"

52801 .004"

52802 .005"

52803 .006"

52804 .007"

52805 .008"

52806 .009"

52807 .010"


Precis ion Layout and Measuring

Items may not be exactly as illustrated, Specifications may change without notice.

Contour Marker®The Curv-O-Mark® Contour Marker is a compact, time-saving tool used to layout pipe and structural steel joints. Laterals at any angle, tees, wyes, crosses, elbows – any type or size of joint can be quickly and precisely laid out. No more complicated mathematical formulas. No more cut and try. No more needless material waste.

xThe Contour Marker can be used to layout pipe from 1-1/2 to 18 in. diameter, or structural steel members up to 18 in. xThe Contour Marker consists of an X-shaped frame, calibrated protractor, and a triple-jointed marking arm and holder. xThe holder accepts a soapstone crayon (included), felt pen or pencil. xThe frame easily folds into a compact tool that fits into a pocket or carrying case. It can be used rightside up or upside down, depending on the direction of the line to be scribed. xThe protractor is calibrated on both sides –one in degrees, the other in rise inches per-foot–to service any type of measurement need. xThe unit comes with a Structural Adaptor designed to simplify the layout of structural joints, including I-beams, angles, channels, square tubing and similar shapes. xThe optional Combination Adaptor Accessory allows the Contour Marker to layout joints on larger size pipe, as well as scribe compound angles with just one setting. xThe Contour Marker is made from durable, lightweight aluminum. It requires minimal maintenance, only occasional oiling of the joints, to provide long service life.

0721-0000

xThe Contour Marker is easy to use. Layout angles are set with the marker's calibrated protractor and scribed directly onto the pipe using the marking arm. No mathematical equations are required.

Leather Carrying Case xStock No. 3

0721-0002

107



Jumbo Contour Marker™

A larger version of the Contour Marker, The Jumbo Contour Marker (JCM) has been developed for use in the layout of large diameter pipe, from 8 to 48 in. With its Structural Adaptor, the JCM can be used in the layout of extremely large structural steel members up to 48 in. wide.

xThe JCM comes complete with a durable web strap that helps hold the unit in place during layout. A built-in adjustable dial bubble protractor ensures accurate centerline location. xA soapstone crayon is included. xLike the standard model, the JCM's capability can be increased with the Combination Adaptor Accessory.

0721-0003

xA built-in protractor provides easy, accurate measurement.

Combination Adaptor AccessoryDesigned for use with the Standard and Jumbo Contour Markers, the Adaptor simplifies handling and increases layout capacity.

xThe Adaptor permits use of all four sides of the Contour Marker and permits marking on small diameter pipe, over nipples, old welds or on wrapped pipe. xThe Adaptor can also provide layouts with compound angles using a single setting, or any degree of take-off on elbows and turns up to 90 degrees.

SKU Description

0721-0001 Standard Combination Adapter

0721-0004 Jumbo Combination Adapter

108



Flange Aligner BaseRemove the difficulty of flange aligning and squaring with a simple tool that holds a square in the needed position without tying up one's hands.

xThe Curv-O-Mark® Aligner Base is notched at either end for ease in aligning on the centerline of the pipe and has two 2S-pound pull, cast-in magnets for holding either a flat horizontal or vertical position. xThe Base will accept either leg of a standard or combination square and will work on pipe diameters from 1 in. on up, requiring only the extension of the legs of the square being used to accommodate larger diameters. xThe Flange Aligner Base is made from lightweight, durable aluminum.

0721-0029

Cast-in magnets hold the flange aligner base in either a flat or vertical position. (Square not included.)

Pipe Flange AlignersFast, accurate pipe construction is possible with this self-determining flange aligning tool. The Aligner inserts easily into pipe, centers snugly against the inside pipe diameter and automatically aligns with the pipe axis.

xThe Pipe Flange Aligner is quickly adjustable for all types of flanges or pipe sizes ranging from 3 to 12 in. diameter.

0721-0009

109



Circle-ellipse Projector

Perfect circles, ellipses or oblong circles can now be easily made on any irregular flat or round surface.

xThe Projector features a protractor with sliding rods and an adjustable lever to lock in the specified layout. xA strong, 20-pound pull magnetic base holds the Projector in position during layout. xA durable web strap (included) holds the unit secure on nonmagnetic surfaces and can be used on either side of the vertical column. xThe Projector can also be used to layout lateral intersections of different diameter pipes, or to project circles from 1-1/2 to 18 in . diameter on flat surfaces intersecting at angles from 0 to 70 degrees from vertical. xAttachments to develop larger diameter circles are available. xThe Projector is equipped with a soapstone crayon and also works with chalk, pencil or steel scribe.

0721-0014

Centering Pin xA hardened steel pin for use with the Curv-O-Mark® Standard Centering Head (0721-0005). Suitable for marking, but should not be used as a center punch.

0722-0001

Soapstone and Holders xCurv-O-Mark® soapstone is grain cut to ensure good strength and long service life. Its low water content increases hardness and provides high resistance to breakage. It has a texture that results in excellent marking quality. Soapstone is available in round or flat crayons. xFor protection of soapstone crayons, a choice of two, durable anodized aluminum cases are available. The design allows the use of over 90 percent of the crayon .

SKU Description

0721-0021 1/4" x 5" Round Soapstone

0721-0022 3/16" x 1/2" x 5" Flat Soapstone

0721-0023 Round crayon holder

0721-0024 Flat crayon holder

Centering HeadsCurv-O-Mark® Centering Heads aid in the setting of centerlines, establishing angles and marks for butt-ins, locating points inside pipes and tanks, laying out keyways and measuring declivity.

xThe Standard Model is used on pipe 1/2-in. diameter and larger. It has 4-in. V-type head and is fitted with an adjustable dial bubble protractor (DSL) and a manually operated hardened centering pin. xThe Jumbo Centering Head is for pipe 1-in. diameter and up. It has an 8-in. V-type head, and a DSL. A spring loaded hardened centering pin eliminates the need for a hammer. Just make the alignment and press the trigger.

SKU Description

0721-0005 Standard Centering Head (above)

0721-0006 Jumbo Centering Head (below)



Fitter Welder Protractor

This 90 degree protractor has a matching locking lever to set and hold the tool at the desired angle.

x It is equipped with a 5/8 in. by 10 in. tapered arm to complete finding of angles or desired bends, or to determine any portions of elbows. xThe tool is mounted in a 3/4-in. wide frame with a 3/8-in. by 6-in. cast-in rod. It comes with a 25-pound pull magnetic base for holding the protractor frame in position. xThe unit can be used manually or with a magnetic base, as shown below.

0721-0008

Versi·Mag & HolderHere are two versatile magnetic aids that free up hands for other work.

xThe Versi-Mag is a Single 25 pound magnet cast in a square end body that can be used for the line up of steel parts for welding or machining. xThe Versi-Mag Holder works as a jig or line-up fixture, and can hold leads, hoses, torches or other devices. It consists of two 25 pound pull magnets, each cast in an aluminum body and machined with square ends. These are then hinged to swing through a 90 degree angle. xThe bodies are fitted with either a holding pin or clamp to receive various tools.

SKU Description

0721-0018 Versi-Mag

0721-0019 Versi-Mag Holder

Radius MarkersAvailable in four sizes for scribing circles up to 80-in. diameter.

xAll are a folding type design-the three smaller models will fit conveniently into a shirt pocket. xAll have sturdy friction joints to maintain rigidity and accuracy, and are made from lightweight, rustproof aluminum for long wear. xA soapstone crayon is already installed in each radius marker.

SKU Description

0721-0010 Mini – Up to 8" Radius

0721-0011 Small – Up to 20" Radius

0721-0012 Standard – Up to 24" Radius

0721-0013 Jumbo – Up to 40" Radius

Multi-Trammel Heads

For reliable marking using standard 1/2-in. pipe, heads feature radius set points cast in alignment with marking pointers for easy setting.

xEach is equipped with 1/4-in. screws and squared on the back side for perpendicular alignment. xThe stationary head holds a 1/4-in. case hardened center point. xThe moveable head has a 1/8-in. steel scribe hardened to 59 rockwell. xThe chalk holder will accept round, square or flat soapstone crayon, pencil or steel point scribe. xMarks from 1-1/2-in. circle to any diameter needed, depending on length of pipe used as a trammel bar. xHeads are made from durable aluminum. xEach set weighs approximately 8 oz. xAn Allen wrench, soapstone, scribe and pointer are included.

0721-0016



Universal LevelThe Curv-O-Mark® Universal Level is a multi-purpose tool. The unit features a 360 degree adjustable protractor dial bubble (DSL) that ensures accurate leveling and permits the following additional uses:

xSetting a predetermined pitch of a string of pipe xSetting the angle of laterals to a precise degree xTrueing vertical runs xTwo-holing flanges

The Level has two cast-in 25 pound magnets (exerting a 50 pound pull) to securely hold the unit in place on any steel surface, including the underside of a pipe or beam. This permits hands-free leveling, a welcome aid in tight spots. And, since the bubble is mounted on a protractor dial, the Level may be used in any position and still read accurately.While one face of the Level is magnetic, both faces have deep, cast-in grooves that make the Level self-centering on the contour of the pipe. Because the magnets are cast in, they do not interfere with the use of the Level on nonmagnetic materials, such as aluminum, copper, lumber, stone or other materials requiring leveling.For aligning pipe flanges (two-holing), the Level comes with a two-threaded, self-aligning conical spacer and conical nut and bolt units. These are designed to fit any size bolt hole spaced between 2-1/4 in. to 8-in. centers on flanges. This permits the orientation of flange bolt holes for any size pipe. Designed primarily for pipefitting applications, the Universal Level is a valuable tool for any craft required to use a level or a plumb bob:

xFor structural ironworkers, the powerful holding magnets provide an extra hand xElectricians will find the Level useful in laying out and lining up heavy conduit xWith the aid of a handy conversion chart, carpenters can use the Level for the layout of roof rafters

Bolt holes that are offset can be matched by setting the DSL at the desired offset angle prior to rotating the flange.

0721-0030

Two-holing is simplified with the Universal Level. Self-aligning spacer bolt units are attached in the two adjacent bolt holes at the top or bottom of the flange. With the DSL dial set at 0 degrees, the flange is rotated until the bubble is centered.

If adjacent top or bottom holes cannot be used, two-holing can be achieved using side bolt holes. In this instance, the DSL dial is set at 90 degrees and the flange is rotated until the bubble is centered.

A built-in adjustable dial bubble protractor (1) ensures accurate centerline location. A cast-in table (2) indicates rise per foot in both inches and meters. A cast-in groove (3) makes the level self centering on the contour of pipe.

112



Dial-Angle-Flange Level

A versatile tool that can be used as a dial degree utility level or, with attachments, for two-holing flange alignment.

xThe unit is made of cast aluminum with a protective housing containing an adjustable DSL. xFitted with a threaded, self-aligning conical spacer and conical nut and bolt units for fastening the Level to a pipe flange. xOne of the nut and bolt units is stationary, while the other slides up to 5-1/2 in. along a slot in the level to accommodate various flange bolt hole spacings from 2 to 5-1/2 inches. xThe body of the tool is 1/2-in. thick with a machined surface. xThe level bubble is protected from weld splatter and breakage with a built-in housing around the DSL.

0721-0017

A built-in adjustable dial bubble protractor (1) ensures accurate centerline location. A cast-in table (2) indicates rise per foot in both inches and meters. A cast-in groove (3) makes the level self centering on the contour of pipe.

Pro·Mag Level

A lightweight, easy to use tool for determining angles, the Pro-Mag Level has two cast-in 25 pound pull magnets that hold securely to any steel surface.

xThe unit has a 360-degree adjustable DSL with two 90-degree quadrants graduated in 2-1/2-degree increments. xAlso cast in are tables used to convert degree-of-angle to rise-in-inches-per-foot or millimeters-per-meter. xA groove on the bottom edge permits use on a small pipe. xThe Pro-Mag Level is 9 in. long, 2 in. high and 3/4 in. thick. xMade from cast aluminum. xThe unit is ideal for pipefitter, welder, jig builder or anyone who has to determine angles or do setup work

0721-0007

Centering Bushing Set xReplacement parts for stock no. 0721-0017 and 0721-0030 xDual thread bolt xSpacer 5/16-in. X 16 threads xKnob nut 1/4-in. X 20 threads

0722-0002

Dial-Set-Level (DSL) xThe DSL is an adjustable bubble protractor used with a number of Curv-O-Mark® tools (Stock No. 0721-0003, 0005, 0006, 0007, 0017, 0030). The protractor covers 180 degrees through two 90 degree quadrants, reading in 2-1/2 degree increments. xThe bubble is cast in the aluminum dial.

0722-0000



Wrap-A-Round

An inexpensive tool for marking straight lines around pipe, or for use as a straight

edge. Made out of flexible gasket material, with good resistance to heat and cold. xAll Wrap-A-Rounds are available in two colors. These designate material type and service temperature. xGG (Gray) material is used for high temperature applications up to 550°F. xB (Black) material has a service temperature of up to 350°F. xBoth material types are asbestos free. xExtra small and special order sizes are unmarked. All other sizes are printed with a scale in inches, pitch chart, tangent chart and other useful markings. xWrap-A-Rounds in 3.88" and 5.00" feature a metric scale and pitch chart.

Size W x L Pipe Diam.

B (Black) GG (Gray)

Stock # Item # Stock # Item #

EX·SMALL 1.94" x 2' 1" to 3" 150B 0720-0001 150GG 0720-0027

SMALL 2.50" x 2' 1" to 3" 152B 0720-0004 152GG 0720-0028

MEDIUM 3.88" x 4' 3" to 6" 164B 0720-0007 164GG 0720-0029

LARGE 3.88" x 6' 3" to 10" 176B 0720-0010 176GG 0720-0030

EX-LARGE 5.00" x 7' 4" to 12" 177B 0720-0013 177GG 0720-0031

EX·LARGE 5.00" x 9' 6" to 16" 179B 0720-0016 179GG 0720-0032

SPECIAL 3.88" x Desired length 184B 0720-0019 184GG 0720-0033



Pro·Mag Burning Square

The CURV-O-Mark® Pro-Mag Burning Square is a precise tool used in structural thermal cutting and layout. The tool base is a perfect square containing powerful cast-in magnets. This permits placement in any position.

xThe tool surface is embossed with a protractor inscribed with two 9O-degree quadrants graduated in 1-degree x increments. xThe top of the tool carries an 18-in. ruler blade divided in 1/8-in. increments. xThe ruler can be locked in place at the desired angle setting by hand tightening of the adjustment knob. xThe ruler blade is on a raised plane. This permits its use as a straight edge when flame cutting, without distortion or marring. xThe blade will also accept attachments or extensions that allow an overall length up to 72 in. xmade of cast aluminum.

0721-0020

Magnetic Burning Guide

Designed for use with a burning torch or as a straight edge, the Burning Guide is cast of strong, durable material to withstand heat and spatter.

xThe tool's base has three 30-pound pull cast-in magnets for use in any position. xA 24-in. blade on a raised plane is standard.

0721-0025

Attachments For Pro-Mag Burning Square & Magnetic Burning Guide

SKU

0721-0028 72" Overall length





Adjustable Fillet Weld Gauge

xFor equal and unequal legged fillet welds xMeasures 15 different weld sizes plus throat thickness xTo measure fillet welds place the irregular curve edge flush to the horizontal toe of the weld so the straight edge is in line with the horizontal member xTo measure weld throat thickness place the 45 degree angle end flush to the horizontal and vertical members. Loosen the thumb screw and slide the pointer until it touches the face of the weld.

3

Hi-Lo Welding Gauge

xSolid Stainless Steel Construction xNew slim design, 30% lighter xViewing window for easy-to-read measurements xMeasures internal alignment of pipe after fit up/alignment xCuts radiographic rejects xMeasures internal misalignment of pipe before and after tacking xMeasurements read English one side, Metric opposite side

1

Single Purpose Hi-Lo Gauge

xMeasures rootweld space xMeasures internal misalignment xEliminates rejects and improves productivity

2

Fillet Weld Gauge Set x7 Piece Fillet Weld Gauge: xKnurled nut holds set together xAll edges deburred xAll letters AL\ID characters chemically etched xHandy pocket case xAllows fast, accurate measurement of 11 fillet weld sizes: 1/8, 3/16, 1/4,5/16, 3/8,7/16,1/2,5/8,3/4,7/8, and 1 inch. Includes metric equivalents. xDetermine either concave or convex weld sizes.

8

WTPS Gauge w/ Calibration Lock

xUndercut shall be no more than .010 inches (0.25 mm) deep when the weld is transverse to the primary stress in the part that is undercut. xWTPS Gauge is precision made from stainless steel. xAll markings and dimensions are laser engraved for ease and clarity when reading. xThis gauge comes with a precision ground calibration block and each block has been ground to .0005 tolerance for exceptional accuracy.

7

Automatic Weld Size Gauge

xFor accurate calibration of butt and fillet type welds. xCheck reinforcement xCheck the throat of fillet weld xTo determine the leg size of the fillet weld

6

GAL Gage - Skew-T Fillet Gauge

The Calculator: xA handy compilation of mathematical relationships between leg length, throats, skew angles, and inspection dimensions. xA must for designers and inspectors. xThe perfect companion to the G.A.L. Skew-T Fillet Weld Gauge

The Skew-T Gauge: xMeasures the acute side xChecks the angle of the vertical member xMeasures the obtuse side

9



Gap-A-Let® Socket Weld Contraction Rings

Get Proper Socket Weld Fit-Up In One-Tenth The Time! xGap-A-Let® is a split ring that is engineered and designed to give you a pre-measured 1/16" minimum gap for socket welds. Made from a certified stainless steel, Gap-A-Let® resists corrosion from chemicals, radioactive materials, and water. xGap-A-Let®'s spring tension makes it fit tightly into all standard sized fittings from 1" to 4". (Non-standard sizes are available upon request.) Once inserted into the fitting, the Gap-A-Let® ring becomes a permanent part of the joint. It will not rattle or vibrate even under extreme pressure.

Where Is It Used? xDesigned for use on any socket weld application, Gap-A-Let® rings are suitable for Power Piping (Nuclear, Conventional), Industrial Hydraulics, Welded Railroad Air Brake Piping, Petrochemical Plants, Fertilizer Plants, Shipbuilding, and the list goes on and on.

What Does It Do For You? xCut fit-up time by 90% xSave thousands of dollars in cracked weld repairs. xSocket welds that once took 15 minutes or more to fit-up now take just seconds. There is no measuring, scribing, or re-measuring. Just pop the Gap-A-Let® into the fitting and insert pipe into the fitting, Gap-A-Let® socket weld contraction rings automatically set the required 1/16" minimum gap so you're ready to weld. xAnd because these rings are so easy to use, they eliminate the problems caused by guessing the gap. No longer is there a need to scribe into hard-to-mark metal pipe walls. With Gap-A-Let® rings, quality control inspectors can concentrate on the quality of the weld and not spending valuable time measuring for proper gapping. And since the costly problem of cracked welds due to improper gap is practically eliminated, your pipes can safely transport fluids the first time and every time.

15

Three easy steps make proper 1/16" minimum gap socket welds in seconds.

1. Fitter compresses Gap-A-Let® ring to fit into pipe fitting.

2. Fitter seats ring into fitting. Spring tension holds ring tightly in place, assuring no rattling or vibration even under extreme pressure. Ring becomes a permanent part of the joint.

3. Fitter inserts pipe into fitting. Gap-A-Let® ring automatically assures the minimum gap (1/16") to meet requirements of ANSI 31.1 Section III, ASME & military codes.

CamBridge Cam Gauge

xUse to measure excess weld metal, fillet weld throat, and angle of preparation. xThe following is possible in either inches or millimeters: Angle of preparation, 0º to 60º Excess weld metal (capping size) Depth of undercut Depth of pitting Fillet weld throat size Fillet weld length Misalignment (high-low)

4

Mini Sub Gauge

xSliding pointer for different pipe schedules xSliding pointer for throat measurement xStainless Steel

14

Mini Fillet Weld Keys

xMeasures fillet weld leg xMeasures fillet weld throat x11 different sizes in English and Metric conversion xStainless Steel xSet comes with handy key chain

16

Layout & Measuring

Documents

Transcript of Layout & Measuring