Katalog 2010-En Kse-uk2 (1)
-
Upload
dan-stride -
Category
Documents
-
view
109 -
download
3
Transcript of Katalog 2010-En Kse-uk2 (1)
Complete Catalogue 2010
E I M1 Ex ia I E II 2G Ex ia IIC T4 E II 2D Ex tD A21 T130°C IP67 E II 1G Ex ia IIB T4
www.kse-lights.com
8 Southampton Road
Ringwood
Hampshire BH24 1HY
United Kingdom
Phone +44 (0) 1425-477164
Fax +44 (0) 1425-477164
Mobiles +44 (0) 7738 890 523 (Dan), +44 (0) 7768 322 355 (Richard)
KSE-LIGHTS Lamps KS-7600 and KS-7610
KS-7600 KS-7610 is available with yellow, orange or black casing.
www.kse-lights.com2
Technical data KS-7600 2-step switch (emergency light, main light)
power supply Lithium battery 3,7 V - 2,8 Ah
charging time < 7 hours
charger output DC 4,7 V; < 600 mA
weight 130 g
working temperature -20 °C to +60 °C
battery longevity > 80 % capacity after 500 x recharged
warranty 2 years
ingress protection IP67 (waterproof to at least 1m depth)
illuminance*, emergency light > 900 lux (at least 15 lm)
illuminance*, main light > 2200 lux (at least 35 lm)
working duration, emergency light > 50 hours
working duration, main light > 14 hours
explosion proof mode E II 2G Ex ib IIC T4
* illuminance of 1 m distance
Technical data KS-7610 3-step switch (emergency, main or intense light)
illuminance*, emergency light > 900 lux (at least 15 lm)
illuminance*, main light > 2200 lux (at least 35 lm)
illuminance*, intense light > 3000 lux (at least 65 lm)
working duration, emergency light > 50 hours
working duration, main light > 14 hours
working duration, intense light > 6 hours
E: symbol for protection against explosion according to ATEX standards.
II: devices of group II are permissible for use in environments outside mining.
2: Category 2 means adaption to zone 1 of explosiveness. These are locations where explosive atmospheres can occur
regularly; this means 10-1000 h per year. These are e.g. fi lling stations, environments of tanker or working pits for motor-
cars.
G: with permission for gases and vapours.
Ex: with permission for use in surroundings with explosive atmosphere.
ib: class of protection. ib = intrinsically safe. The circuits of the lamp will neither in regular function nor in case of failure
produce any sparks that can ignite an explosive atmosphere.
IIC: The lamp has permission for explosives class IIC and may be used, when gases of this class are present, e.g.
hydrogen, vapours of fuel or acetylene.
T4: The lamp has permission for temperature class T4. It may not be used when gases are present that will ignite below 135 °C.
II 2G Ex ib IIC T4E x
KS-7610 at a F220 helmet
KSE-LIGHTS Lamp KS-7650
KS-7650
KS-7650
II 2G Ex ib IIC T4E x
Technical data KS-7650
power supply Lithium battery 3,7 V - 1,4 Ah
charging time < 5 hours
charger output DC 4,7 V < 600 mA
weight 115 g
working temperature -20°C to +60°C
battery longevity > 80% capacity after 500 times recharged
warranty 2 years
ingress protection IP67 (waterproof to at least 1m depth)
illuminance*, emergency light > 400 lux (at least 12 Lumen)
illiminance*, main light > 1200 lux (at least 30 Lumen)
working duration, emergency light > 20 hours
working duration, main light > 7 hours
explosion proof mode E II 2G Ex ib IIC T4
* illuminance at 1 m distance
www.kse-lights.com3
KS-7650 at a F120 helmet
KS-7650 at a F220 helmet
E: symbol for protection against explosion according to ATEX standards.
II: devices of group II are permissible for use in environments outside mining.
2: Category 2 means adaption to zone 1 of explosiveness. These are locations where explosive atmospheres can occur
regularly; this means 10-1000 h per year. These are e.g. fi lling stations, environments of tanker or working pits for motor-
cars.
G: with permission for gases and vapours.
Ex: with permission for use in surroundings with explosive atmosphere.
ib: class of protection. ib = intrinsically safe. The circuits of the lamp will neither in regular function nor in case of failure
produce any sparks that can ignite an explosive atmosphere.
IIC: The lamp has permission for explosives class IIC and may be used, when gases of this class are present, e.g.
hydrogen, vapours of fuel or acetylene.
T4: The lamp has permission for temperature class T4. It may not be used when gases are present that will ignite below 135 °C.
www.kse-lights.com
KSE-LIGHTS Lamps KS-7700, KS-7700H2, KS-7710
KS-7700H2KS-7700 KS-7710
4
Technical data KS-7700 and KS-7700H2 2-step switch (emergency and main light)
power supply Lithium battery 3,7 V - 2,8 Ah
charging time < 7 hours
charger output DC 4,7 V; < 600 mA
weight 130 g
working temperature -20 °C to +60 °C
battery longevity > 80 % capacity after 500 times recharged
warranty 2 years
ingress protection IP67 (waterproof to at least 1m depth)
illuminance*, emergency light > 900 lux (at least 15 Lumen)
illuminance*, main light > 2200 lux (at least 35 Lumen)
working duration, emergency light > 50 hours
working duration, main light > 14 hours
explosion proof mode KS-7700: E I M1 Ex ia I
KS-7710: E I M1 Ex ia I
KS-7700H2: E I M1 Ex ia I/II (H2)
* illuminance at 1 m distance
Technical data KS-7710 3-step switch (emergency, main and intense light)
illuminance*, emergency light > 900 lux (at least 15 lm)
illuminance*, main light > 2200 lux (at least 35 lm)
illuminance*, intense light > 3000 lux (at least 65 lm)
working duration, emergency light > 50 hours
working duration, main light > 14 hours
working duration, intense light > 6 hours
E: symbol for protection against explosion according to ATEX standards.
I: Tools of class I may be used in mines with explosive atmospheres and occurence of combustible dust.
M1: category M1: very high protection class. The use of this light may be continued even when an
explosive atmosphere exists.
Ex: marking after AtEx-rules: permission for use in environment with danger of explosives
ia: class of protection. ia = intrinsically safe. The circuits of the lamp will not produce any sparks that
can ignite an explosive atmosphere.
This is even true if two rare failures occur simultaneously.
I: accepted for use in atmospheres with methane.
I/II (H2): also accepted for use in atmospheres with hydrogen (gas of group IIC).
I M1 Ex ia IEx KS-7710 at miners helmet
5
KSE-LIGHTS Lamps KS-8600 and KS-8700
Model KS-8600 with ATEX-permission for zone 0 and dust
Technical data KS-8600 and KS-8700
power supply Lithium battery 3,2 V - 2,0 Ah
charging time < 7 hours
charger output DC 4,2 V; < 600 mA
weight 125 g
working temperature -20 °C to +60 °C
battery longevity > 80 % capacity after 500 times recharged
warranty 2 years
ingress protection IP67 (waterproof to at least 1m depth)
illuminance*, emergency light > 900 lux (at least 15 Lumen)
illuminance*, main light > 2200 lux (at least 35 Lumen)
working duration, emergency light > 25 hours
working duration, main light > 9 hours
explosion proof mode E II 1G Ex ia IIB T4
E II 2D Ex tD A21 T130°C IP67
E I M1 Ex ia I
* illuminance at 1 m distance
E: symbol for protection against explosion according to ATEX-standards.
II: devices of group II are permissible for use in environments outside mining.
1: Category 1 means adaption to zone 0 of explosiveness. These are locations where explosive atmospheres will always be
present. This is the interior of tank farms.
G: with permission for gases and vapours.
Ex: with permission for use in surroundings with explosive atmosphere.
ia: class of protection. ia = intrinsically safe. The circuits of the lamp will not produce any sparks that can ignite an explosive
atmosphere.
This is even true if two rare failures occur simultaneously.
IIB: The lamp has permission for explosive class IIB and may be used, when gases of this class are present, e.g. vapours of fuel.
T4: The lamp has permission for temperature class T4. It may not be used when gases are present that will ignite below 135 °C.
II 1G Ex ia IIB T4E x
Zone 0, Permission D2 for Dust and M1
Model KS-8700 with M1-permission
www.kse-lights.com
II 2D Ex tD A21 T130°C IP67E
I M1 Ex ia IEx
6
KSE-LIGHTS Handlamps
These handlamps are offered in two sizes: with 3 Ah-battery or with 6 Ah-battery. The two lamps in the left picture show the small
version, in the other pictures the large version is shown.
Both types are available black or yellow and also with ATEX-permission 2G (industrial use or Firefi ghters), M1 (mining) and also
without ATEX-permission.
They can be carried very comfortably in a front pocket or at the carrying strap of a compressed air breathing apparatus.
Technical Data KS-8000 without ATEX
KS-8650 ATEX 2G
KS-8750 ATEX M1
power supply Lithium battery 3,2 V - 3 Ah
charging time < 7 hours
charger output DC 4,2 V; < 600 mA
weight 160 g
length 12,5 cm
working temperature -20 °C bis +60 °C
battery longevity > 80% capacity after 500 times recharged
warranty 2 years
ingress protection IP67 (waterproof to at least 1m depth)
illuminance*, emergency light > 1500 lux (at least 18 lm)
illuminance*, main light > 2200 lux (at least 32 lm)
illuminance*, intense light > 3000 lux (at least 60 lm)
working duration, emergency light > 27 hours
working duration, main light > 14 hours
working duration, intense light > 10 hours
* illuminance in 1 m distance
Technical Data KS-8100 without ATEX
KS-8690 ATEX 2G
KS-8790 ATEX M1
power supply Lithium battery 3,2 V-6 Ah
charging time < 14 hours
charger output DC 4,2 V; < 600 mA
weight 260 g
length 19,5 cm
working temperature -20 °C bis +60 °C
battery longevity > 80% capacity after 500 times recharged
warranty 2 years
ingress protection IP67 (waterproof for at least 1m depth)
illuminance*, emergency light > 1500 lux (at least 18 lm)
illuminance*, main light > 2200 lux (at least 32 lm)
illuminance*, intense light > 3000 lux (at least 60 lm)
working duration, emergency light > 54 hours
working duration, main light > 28 hours
working duration, intense light > 20 hours
* illuminance in 1 m distance
II 2G Ex ia IIC T4E x
I M1 Ex ia IEx
Without ATEX
www.kse-lights.com
KSE-LIGHTS Signal Lamps KS-8500, KS-8680, KS-8780
White light at the front with highpower-LED
The red, green and yellow permanent light is produced with the newest generation of SMD-LED.
The signal lamps are available in two versions: with white and red light or with white, red, green and yellow light.
They are suited to nearly all carrying and charging systems of KSE-LIGHTS.
Coloured light through transparent back of the lamp
www.kse-lights.com7
Technical Data2-step lighting (main white, red) or
5-step lighting (emergency light, white, red, green, yellow)
power supply Lithium battery 3,2 V - 2 Ah
charging time < 7 hours
charger output DC 4,2 V; < 600 mA
weight 125 g
working temperature -20 °C to +60 °C
battery longevity > 80% capacity after 500 times recharging
warranty 2 yearsingress protection IP67 (waterproof to at least 1m depth)
illuminance*, white emergency light > 900 lux (at least 15 Lumen)
illuminance*, white main light > 2200 lux (at least 35 Lumen)
luminous fl ux, coloured signal light ca. 10 Lumen
working duration, emergency light > 25 hours
working duration, main light > 9 hours
working duration, signal light > 25 hours
* illuminance at 1 m distance
II 2G Ex ia IIC T4E x
Model KS-8680 with ATEX- permission:
Model KS-8500 without ATEX- permission
Model KS-8780 with ATEX- permission:
I M1 Ex ia IEx
KSE-LIGHTS Flashing Combination Lamps KS-8610 and KS-8710
White light at the front with highpower-LED
Technical Data4-step lighting (emergency light, white, red fl ashing, white & red fl ashing)
power supply Lithium battery 3,2 V - 2 Ah
charging time < 7 hours
charger output DC 4,2 V; < 600 mA
weight 125 g
working temperature -20 °C to +60 °C
battery longevity > 80% capacity after 500 times recharged
warranty 2 yearsingress protection IP67 (waterproof to at least 1m depth)
illuminance*, white emergency light > 900 lux (at least 15 Lumen)
illuminance*, white main light > 2200 lux (at least 35 Lumen)
luminous fl ux, red fl ashing light ca. 10 Lumen
working duration, emergency light > 25 hours
working duration, main light > 9 hours
working duration, fl ashing light > 28 hours
* illuminance at 1 m distance
II 2G Ex ia IIC T4E x
The fl ashing combination lamps are apted to nearly all carrying and charging systems of KSE-LIGHTS.
Model KS-8610 with ATEX- permission:
Red fl ashing light through transparent back of the lamp
Model KS-8710 with ATEX- permission:
I M1 Ex ia IEx
www.kse-lights.com8
Also available with blue fl ashing light.
www.kse-lights.com
KSE-LIGHTS warning lamps KS-6700w, KS-6200
The warning lamps KS-6700w (with M1-permission) and KS-6200 (without ATEX-permission) are performing four functions at a time:
fl ashing or permanent light of red and yellow.
Through the transparent front ring the light is emitted in a broad angle.
Working duration with main light is at least 24 hours in fl ashing light mode and at least 9 hours with permanent light.
Model KS-6700w with yellow fl ashing or red permanent light mounted to warning signs.
9
Model KS-6200without ATEX- permission
Model KS-6700w with ATEX- permission:
I M1 Ex ia IEx
Technical Data 5-step lighting (permanent red; fl ashing red; permanent yellow;
fl ashing yellow; fl ashing red and yellow)
power supply Lithium battery 3,2 V - 1,5 Ah
charging time < 6 hours
charger output DC 4,2 V; < 600 mA
weight 110 g
working temperature -20 °C to +60 °C
battery longevity > 80% capacity after 500 times recharged
warranty 2 years
ingress protection IP67 (waterproof for at least 1m depth)
luminous fl ux: ca. 10 Lumen
working duration, fl ashing light > 24 hours
working duration, main light > 9 hours
www.kse-lights.com
Model KS-6000: High Quality for a Low Price
working duration, main light > 15 hoursworking duration, emergency light > 100 hoursilluminance*, emergency light > 150 lux (at least 7 Lumen)illuminance*, main light > 1000 lux (at least 30 Lumen)
* illuminance at 1 m distance
The super-light lamp for all those, who need no ATEX-permission.
Suited to nearly all carrying and charging systems of KSE-LIGHTS.
Technical Data KS-6000
power supply Lithium battery 3,7 V - 2 Ahcharging time < 7 hourscharger output DC 4,7 V; < 600 mAweight 110 gworking temperature -20 °C to +60 °Cbattery longevity > 80% capacity after 500 times recharging
warranty 2 yearsingress protection IP67 (waterproof to at least 1m depth)
10
www.kse-lights.com
Directions for use for KS-5300
1. For charging connect the charging wire with the charging jack of the lamp.
2. The control LED of the single charging device and the charging control LED of the lamp will now glow red.
3. When charging is complete, the control LED on the charging device will glow green.
The control LED on the lamp will glow red further.
Technical data KS-5300
primary voltage: AC 110 - 265 V,
50 Hz
output voltage: DC 5,2 V
charging current: 450 - 600mA
charging time: < 7h
weight: 0,06 kg
KSE-LIGHTS Single Charging Devices KS-5300 and KS-5010
12 - 24 V single car charger
charging in progress charging completed230 V single charging device
Technical data KS-5010
primary voltage: DC 12 V - 24 V
output voltage: DC 5,2 V
charging current: 500 mA
charging time: < 7 h
weight: 0,04 kg
without display of charging state
charging wire connected with the lamp
11
Standard Charging System
www.kse-lights.com
Directions for use for KS-5008
1. For charging connect the charging wire with the charging jack of the lamp and fi x the lamp in the clamp on
the charging box.
2. The control LED of the charging place on the box and the charging control LED of the lamp will now glow.
3. When charging is complete, the control LED on the charging box will glow green.
The control LED on the lamp will glow red further.
Technical data KS-5008
charging places 8
primary voltage AC 90 - 265 V, 50 Hz;
DC 12 - 24 V
output voltage DC 5,2 V
charging current 500 mA
charging time < 7h
dimensions 330 mm × 210 mm × 60 mm
(w x h x d)
weight 2,5 kg
KSE-LIGHTS Charging Box KS-5008
The charging box KS-5008 for eight lamps is suited for
input voltages of DC 12 V - 24 V and AC 90 V - 265 V, so
it can be used mobile or stationary. Due to its compact
size it is well suited for use in cars.
The charging box has the dimensions:
330 mm wide x 210 mm high x 60 mm deep and weighs
less than 2,5 kg.
Is supplied complete with all necessary connecting wires.
12
Standard Charging System
www.kse-lights.com
Technical data KS-5536
charging places 36
primary voltage AC 230 V, 50 Hz
power requirement 150 W
output voltage DC 5,2 V
charging current 500 mA
charging time < 7 h
dimensions 780 mm × 670 mm × 70 mm
(w x h x d)
weight 12 kg
Technical data KS-5552
charging places 52
primary voltage AC 230 V, 50 Hz
power requirement 250 W
output voltage DC 5,2 V
charging current 500 mA
charging time < 7 h
dimensions 835 mm × 1100 mm × 105 mm
(w x h x d)
weight 32 kg
KSE-LIGHTS Charging Boards KS-5536 + KS-5552
13
Standard Charging System
Directions for use for charging boards
1. For charging connect the charging wire with the charging jack of the lamp and fi x the lamp in the clamp on
the charging board.
2. The control LED of the charging place on the board and the charging control LED of the lamp will now glow.
3. When charging is complete, the control LED on the charging board will glow green.
The control LED on the lamp will glow red further.
www.kse-lights.com14
90 - 260 V 230 V single charging device
The new charging cup system has many advantages:- Charging cable no longer necessary- Sturdy charging connection that can be cleaned easily if necessary- Fast handling at the charging board- Unique charging system makes theft of lamp unattractive- Suited for all mounting systems- The lamp can additionally be fi xed with a lock at the board if necessary- The charging contacts are not energised before the lamp is pushed into the charging cup
The New M-System With Charging Cup The Lamps
Lamp in single charging device The contacts underneath the lamp are
made from nickel-plated brass.
Model No. Description KS-7700M like KS-7700 but with contacts underneath*
KS-7710M like KS-7710 but with contacts underneath*
KS-7700H2-M like KS-7700H2 but with contacts underneath*
KS-7600M like KS-7600 but with contacts underneath*
KS-7610M like KS-7610 but with contacts underneath*
KS-5330 single charging device with charging cup, 230 V AC
KS-2036-M single charging device with charging cup, 12 - 24 V DC
KS-5535 charging board for 35 lamps
KS-5553 charging board for 53 lamps
The charging cup system is available only for the lamps mentioned above.
The upper charging contact is sealed
Lamp in single charging device
www.kse-lights.com15
Charging board for 35 lamps
Charging board for 53 lamps
Technical data KS-5535charging places: 35primary voltage: AC 230 V / 110 V, 50 Hz power requirement: 140 Woutput voltage: DC 5,2 Vcharging current: < 600 mAcharging time: < 7 hdimensions: 865mm × 560mm × 110mm (w x h x d)weight: 16 kg
The New M-System With Charging Cup Charging Devices
Single charging device KS-5330, resp.
KS-2036-M
Technical data KS-5553charging places: 53primary voltage: AC 230 V / 110 V, 50 Hz power requirement: 250 Woutput voltage: DC 5,2 Vcharging current: < 600 mAcharging time: < 7 hdimensions: 1105mm × 835mm × 155mm (W x H x D)weight: 35 kg
Technical data KS-5330charging places: 1primary voltage: AC 90 - 260 V, 50 Hz power requirement: 4 Woutput voltage: DC 5,2 Vcharging current: < 600 mAcharging time: < 7 hdimensions: 780mm × 670mm × 70mm (w x h x d)
weight: 0,1 kg
Technical data KS-2036-Mfor fi xed installation in cars
Technical data is the same as KS-5330, but:
primary voltage: DC 12 - 24 V
Lamp fi xed with a padlock
Single charging device KS-5010-M
Technical data KS-5010-Mfor the mobile use in cars
Technical data is the same as KS-2036-M
16
KSE-LIGHTS-Holder KS-5525 and KS-5526
www.kse-lights.com
Forehead tape KS-5525 for all lamp models
With the forehead tape KS-5525 all lamps can be carried easily on the head wherever a helmet is not needed. The forehaed tape
is provided with an additional central tape that runs over the head and ensures a safe fi x. The double adjustability allows a fi t on
nearly all head sizes.
The helmet ribbon KS-5526 is made from the forehead tape and four additional polymer hooks. With the helmet ribbon KSE-LIGHTS
lamps can be carried centrally on nearly all helmets, where a durable fi x of lamp holders is not possible. The adjustability of the hooks
guarantees an optimized fi tting of the helmet ribbon. The hooks can easily be removed, when the helmet ribbon is used as a forehead
tape. They are very fl exible, so that the helmet ribbon can safely be mounted on helmets with thick shells, e.g. on military helmets.
Helmet ribbon on industrial safety helmet Fa. Schuberth F110 and DIN helmet
New: with fall-out protection Protective cap Fa. Voss Protective cap Fa. Schuberth
New: Now With Improved Lamp Adaptor
www.kse-lights.com
KSE-LIGHTS-Lampholder KS-5528
Lampholder KS-5528 The lamp will not fall out. KS-5528 mounted on a wall
The lampholder is made from glass fi bre reinforced nylon. It has two slides for the metal clamp of the lamp and a safety clip, that prevents the lamp falling out.To pull the lamp out of the holder, the safety clip must be pressed down at fi rst. The lamp can not be taken out before this is done. The holder will keep its shape to at least 200 °C.The lampholder can fi xed easily with four little screws on nearly every helmet.We recommend that check you with the producer of the helmet in advance if the fi x of the screw-type holder is possible.The holder is also well suited to fi x a lamp either in a car or on wall.
Tips for use- For fi xing drill two holes of 4 mm into the helmet. Insert the rivet with white back from the inside of the helmet and connect it with the opposite rivet from the side of the holder.- Please take care that the opposite rivet will not block the way for the lampholder.
Aluminium holder with fi xation rivets Aluminium holder on a miner‘s helmet Aluminium holder on workers helmet
Aluminium Holder 1015
The aluminium lamp holder is used in mines to fi x lamps on the helmet.The fi tting on the helmet will not build conductive connection into the interior of the helmet.Please check with the producer of the helmet in advance to ensure that the the fi xing of the aluminium holder is possible. The use of the aluminium holder is possible on all Schuberth industrial safety helmets. The approval for the helmets will not be invalidated!
17
www.kse-lights.com18
Fall-out protection KS-2150 for Mining Helmets
Fall-out protection KS-2150 KS-2150 opened with regular holder Lamp secured at miners helmet
The fall-out protection KS-2150 is an addition to the regular lamp holder. It was developed to prevent lamps from falling off the aluminium socket on worker‘s helmets. The fall-out protection KS-2150 is be mounted together with the regular holder of the lamp. The holder ist shifted into the clip of the helmet and the fall-out protection is folded down. Now the lamp will not fall off the helmet unintentionally.The fall-out protection KS-2150 is suited to all KSE-LIGHTS lamp models and chargers.
Reverse Holder KS-2160 for Mining Helmets
The reverse holder KS-2160 was developed especially for use of KSE-LIGHTS lamps in mines with low height, where a high risk of colliding of lamps with the roofs of tunnels or with pillars is present.The regular lampholder will be exchanged with the reverse holder. Power switch and charging jack are then placed securely on the lower side of the lamp. Switching the lamp on and off will be as convenient as before.
Of course, it is possible to use both systems together.
www.kse-lights.com19
Lateral Lamp Holder KS-4000
KSE-LIGHTS holder KS-4000 Examples for the use of KSE-LIGHTS Holder KS-4000
Clip holder KS-5630
With the clip holder all KSE-LIGHTS lamps can be fi xed on jackets or belts.
The new lateral lamp holder was developed in accordance with the standards of the new norm EN-443:2008 for Firefi ghters‘ helmets. The lampholder is made from glass fi bre reinforced nylon. Thus the holder is very lightweight, very sturdy and not infl ammable. With a spherical joint and the variable lamp holder, the lamp can be adjusted in all directions.By means of the new adapter the lamp engages and can no longer get lost unintentionally.The lateral holder can be used with all KSE-LIGHTS helmet lamps.
An application for the approval of the lateral holder for the use with Firefi ghters‘ helmets made by Schuberth is awaited.
www.kse-lights.com20
Long Safety Cord KS-5050
Safety cord with snap link and loop Loop and snap link are connected, thus the
safety cord is usable as neck band
The safety cord is a standard accessory with each lamp delivery. With the safety cord the lamp can be carried around the neck very comfortably. In addition, in mining areas helmet and lamp can be protected with the safety cord when working in shafts. For this purpose the snap link can be fi xed on the belt. The safety cord is 130 cm long.
Short safety cord KS-5040
Safety cord for securing of lamp
and helmet
Neck Band KS-5020 and Short Safety Cord KS-5040With the short safety cord KS-5040 the lamp can be protected on a miners helmet.The short safety cord has a safety relief also.Also available is a neck band KS-5020, which is equipped with two small snap links.
Light Scattering Foil KS-2210
Short safety cord on a helmet Neck band KS-5020
Light scattering foil on KS-7610 Light spot without scattering foil Light spot with scattering foil
If in the close-up range much and equally dispersed light is needed, we recommend the light scattering foil. It is simply affi xed to the light fi eld and can just as easily removed again.
www.kse-lights.com
UK Adaptor KS-5620
The UK adaptor allows mounting of KSE-LIGHTS helmet lamps on nearly all standard UK-holders.
The lamp can be inserted horizontally or vertically into the adaptor as can be seen in the two left pictures.
With the joint of the lamp holder the work space can easily be illuminated perfectly.
Tips for mounting- As a rule, the adaptor fi ts fi rmly into the mounting. In adition it can be fi xed with a screw or with adhesive.
- If the lamp is too loose in the adaptor, the metal clamp of the lamp can be bent a little so that the lamp can be fi xed as
necessary
- The hole in the side allows a direct fi x of the adaptor with a screw if this is needed.
21
The adapter KS-5620 fulfi lls the requirements of the new European standard EN 443:2008 for Firefi ghters‘ helmets.
KSE-LIGHTS-Holder KS-5660 Steel
Lateral holder KS-5660 Holder KS-5660 will be screwed on at the side The holder can be adjusted vertically
The steel holder KS-5660 can be screwed laterally on nearly all helmets.
The holder is vertically adjustable. In combination with the adjustable lamp clip the work space can be illuminated very fl exibly. The
low weight of holder and lamp assure a very comfortable fi t.
22
www.kse-lights.com
Lightweight Handhold KS-5555 and
Heavy Handhold KS-5557
Handhold KS-5555 with carrying loop Handhold with lamp as an angled caplamp
Handhold with lamp as torch light
The handhold KS-5555 changes a helmet lamp
into a handlamp within seconds.
For this, the handhold is simply pushed into the
holder of the lamp. The special construction of
the support at the handhold allows use of the
lamps as a torch light or as an angled caplamp.
Furthermore the metal clip at the back of the
handhold allows a very comfortable wearing of
the lamp either on the clothing or belt.
The handhold is no longer than 12 cm
and is made from a very light and tough
composite of nylon and glass fi bre.
A heavy version is available also.
KS-5555 weighs ca. 40 g, KS-5557 weighs ca.
100 g.
Bicycle Holder KS-5180
The bicycle holder KS-5180 is also made from a composite of nylon and glass fi bre. It can be easily mounted on the steering rod
without any tools. The recommended lamp for use for cycle lighting is model KS-7610.
www.kse-lights.com23
Screw-on Magnetic-holder KS-5532 and KS-5533
The high-power magnetic-holders KS-5532 and KS-5533 can be simply screwed on the lamp holder. The lamp can be fi xed very easily
to almost all ferrous parts. The Neodym-magnets are small, but nevertheless very powerful. The small magnetic-holder KS-5532 weighs
only 14 g, has a diameter of 25 mm and can manage 15 kg of weight. The big magnetic-holder KS-5533 can manage up to 22 kg of
weight and weighs only 37g with a diameter of 32mm.
Magnetic-holder KS-5532 Magnetic-holder KS-5532 on lamp KS-7600
The mounting set KS-5540 for opening visors is easy to install. The set includes the magnetic-holder KS-5532 so that the lamp can
be fi xed very easy and securely. Suitable for almost all visors with aluminium frame.
Magnetic-holder on an iron plate
Mounting Set KS-5540 for Opening Visors
Magnetic holder with Clip KS-5530The magnetic holder KS-5530 is well
suited for working in switch boxes and
whenever static illumiation is needed.
The holder is also equipped with a function
as a clip.
Magnetic holder KS-5530 Magnetic holder KS-5530 with lamp
Cooperation between and
www.kse-lights.com24
KS-7650 at a F220 helmet KS-7610 at a F220 helmet
Since 1. September 2009 the new norm EN-448:2008 for Firefi ghters‘ helmets now exists.
Since this date only such accessories may be mounted on a Firefi ghters‘ helmet, that have been approved. The approval for our
lamps KS-7610 and KS-7650 is now available with the Schuberth helmet F220.
At the beginning of 2010 the new lateral lamp holder KS-4000 will get its approval for the helmets F120, F130 and F220.
www.kse-lights.com25
Standard Business Conditions of KSE-LIGHTS GmbH
1.Scope
For all orders, only our current Standard Terms & Conditions (see below); will apply. Alternative Purchaser’s Terms & Conditions will not apply – unless
specifi cally agreed in writing by KSE-Lights GmbH. A copy of these Standard Terms & Conditions can be downloaded and printed.
2. Conclusion of Contract
Our description of goods and pricing are valid at the time of printing – and are subject to change. KSE-Lights GmbH cannot be held responsible for
changes in product specifi cation and pricing beyond our reasonable control. All prices quoted are nett ex-works and are subject to VAT at the prevail-
ing statutory rate. Carriage and Shipping charges are not included. The contract of sale will be concluded, when the order has been acknowledged by
KSE-Lights – but title to the goods will not pass to the customer until payment in full has been received and funds cleared into our Bank. Cancellation of
orders will only be accepted providing that the customer cancels such order in writing, at least 5 working days prior to despatch.
3. Right of Withdrawal
The buyer can rescind the contract within 14 days of receipt providing notifi cation has been in received in writing – or the goods have been returned to
KSE-Lights within this period. The returned goods are to be addressed to: KSE-LIGHTS GmbH, Brunnenstraße 8, 58285 Gevelsberg, Germany.
We will not accept returned goods unless the return carriage has been paid by the sender, We reserve the right to reduce credit / not credit at all; nor re-
place faulty goods which have been subject to mis-use in any way – including damage caused by excess voltage and such – together with obvious physi-
cal damage to the product; which automatically invalidates our product warranty. For other items returned, the German Distance Selling Act will apply.
4. Delivery
Deliveries will be carried out from stock to the shipping address quoted by the purchaser. If the goods are sent abroad by request of the purchaser or by
a special method of shipment chosen by the purchaser - then the purchaser will pay for the incremental costs incurred. In such cases, the purchaser will
also be responsible for all import costs, duty & taxes incurred in the country of destination. The purchaser will be charged for shipping fees for products
sent of a COD basis; but which are undeliverable for whatever reason. KSE-Lights GmbH cannot be held responsible for delays caused in the shipping of
our products.
5. Terms of Payment
The purchaser’s Invoice has to be paid in advance after order acknowledgement and prior to shipping all goods. Payment against Invoice or COD is only
possible after formal written agreement. The buyer is responsible for additional costs caused thereby. Pre-agreed Invoices are due for payment within 14
days – and are subject to a 2 % settlement discount; or if paid within 21 days, without settlement discount. Export deliveries will only be undertaken on a
Pro-forma Invoice basis.
In the event of delay of payment by the purchaser, KSE-Lights are entitled to demand default interest of 5 % p.a. for private customers and 8 % p.a.
for business customers; above the prevailing base rate of the German Central Bank. In the event that proven higher losses are incurred by KSE-Lights
GmbH; then we reserve the right to levy such further losses to the purchaser. The purchaser has the right for set-off only if any counterclaims are legally
binding or accepted by us in written form.
6. Retention of Title
The delivered goods remain the property of KSE-Lights GmbH until such time that goods have been paid for in full by the purchaser and funds have
cleared into our Bank.
7. Warranty and Liability
In the event that the defective product is due to manufacturing error, the purchaser can request rectifi cation or replacement product due to such error. In
the event that KSE-Lights GmbH are unable to rectify the fault(s); the purchaser is entitled to be re-imbursed the full purchase price of the products and
have his order considered cancelled.
The applicable warranty period is two years from receipt of all new goods. In the case of Used products (re-furbishments / repairs etc); one year warranty
applies to private customers. However, for these products, Business customers are not covered by such warranty. In the case of usual ‘wear & tear’ prod-
ucts – these are not subject to any warranty e.g. protective fi lms etc.
Products deemed ‘under warranty’ will be processed per the above – but KSE-Lights GmbH will not be held liable to the Purchaser for defective products
which have been obtained from our own suppliers in ‘good faith’. Nor will KSE-Lights accept any third party claims arising. Further, we will not accept any
claims relating to loss of profi t to the purchaser, caused by any failure of KSE products; or for any employee related claims.
8. Data Protection
We guarantee that all data collected for fulfi lling a customer purchase order will not be forwarded to any third party will remain confi dential. Only such
data that is essential to process customer purchase orders will be used.
9. Applicable Justice and Place of Jurisdiction
German rights apply excluding the United Nations Convention on Contracts for the International Sale of Goods. Place of Jurisdiction is Gevelsberg,
Germany.
The Standard Terms & Conditions remain valid even if single paragraphs are legally invalid. A legally invalid point will be replaced by a legally binding
condition. Any disputes arising, will be subject to interpretation in German Law.