iPhone 6 Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6FDA.pdf · iPhone 6 Full...

iPhone6FullDisplayAssemblyReplacement

WerxParts www.werxparts.com Page1of15

iPhone 6 Full Display Assembly Replacement

INTRODUCTION Use this guide along with the Werx Repair Mat to replace the cracked or broken screen on your iPhone 6. Follow Werx Repair Mat Steps 1,2,4 to disassemble. Reverse steps for re-assembly. Use this guide to strip and replace your iPhone 6 front panel. It will show you how to remove the home button, front-facing camera and sensor assembly, LCD shield plate, and home button ribbon cable. TOOLS: IMPORTANT Take your time! The repair takes about 20-30 minutes.

Remember that you will be handling fragile parts, so be gentle!

Most screws are different sizes so keep them organized.

Werx Repair Mat



Step 1: Pentalobe Screws

• Before disassembling your iPhone, be

sure it is powered off.

• Remove the two 3.6 mm Pentalobe

screws next to the lightning connector.

Step 2: Front Panel Assembly

• Press a suction cup into the screen,

just above the home button.

Be sure the cup is completely on the

screen to get a tight seal.



Step 3:

• While holding the iPhone down with

one hand, pull up on the suction cup to

slightly separate the front panel

assembly from the rear case.

Take your time and apply firm, constant

force. The display assembly is a much

tighter fit than most devices.

• With a plastic opening tool, begin to gently pry the rear case down, away from the display

assembly, while you pull up with the suction cup.

Step 4:

• Pull the home button end of the front

panel assembly away from the rear

case, using the top of the phone as a

hinge.

Keep the front panel supported at a 90

degree angle in relation to the rear

case.



Step 5:

• Several clips along the top edge of the

front panel form a partial hinge,

allowing the front panel assembly to

swing open like a book.

During reassembly, align the clips just

below the top edge of the rear case.

Then, slide the front panel upward until

its top edge is flush with that of the rear

case.

Step 6:

• Use the Werx repair mat to keep

screws organized and prevent screw

misplacement damage

• Remove the following five Phillips

screws securing the front panel

assembly cable bracket:

o Three 1.2 mm Phillips screws

o One 1.7 mm Phillips screw

o One 3.1 Phillips screw



Step 7:

• Remove the front panel assembly cable

bracket from the logic board.

Step 8:

• Using a plastic opening tool disconnect

the front-facing camera and sensor

cable connector.



Step 9:


the home button cable connector.

Step 10:


the digitizer cable connector.



Step 11:

• Finally, using a plastic opening tool

disconnect the display data cable

connector.

Step 12:

• Remove the front panel assembly from

the rear case.



Step 13: Home Button

• Remove the two 1.9 mm Phillips

screws securing the home button

bracket.

Step 14:

• Remove the home button bracket from

the front panel.



Step 15:

• Using the plastic opening tool

disconnect the home button cable

connector by pushing it up and away

from the home button.

Step 16:

• Gently push the top left corner of the

home button up away from the front

panel.

Do not push the home button all the

way through you only need to get a

corner free so that you can pry it free

with a spudger.



Step 17:

• Use the point of a spudger to carefully

separate the home button cable from

the adhesive securing it to the front

panel.

Step 18:

• Once all the adhesive has been

separated, remove the home button

from the front panel.



Step 19: Home Button

• Insert the home button to the front

panel.

Step 20:

• Connect the home button cable

connector.



Step 21:

• Insert the home button bracket from the

front panel.

Step 22:

• Insert the LCD assembly to the rear

case.

• Connect the following flex cable to the

logic board:

o Display data cable

o Digitizer cable

o Home button cable

o Front-facing camera and censor

cable



Step 23:

• Insert the front panel assembly cable

bracket to the logic board.

Step 24:

• Insert five Phillips screws to securing

the front panel assembly cable bracket.



Step 25:

• Align the clips just below the top edge

of the rear case. Then, slide the front

panel upward until its top edge is flush

with the rear case.

Step 26:

• Run your fingers along the sides being

sure the assembly slips evenly into the

frame.



Step 27: Pentalobe Screws

• Insert the two Pentalobe screws next to

the lightning connector.

iPhone 6 Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6FDA.pdf · iPhone 6 Full...

Documents

Transcript of iPhone 6 Display Assembly Replacementodrepairservices.com/wp/PDF/iPhone6FDA.pdf · iPhone 6 Full...