ICAR CENTRAL INSTITUTE OF POST HARVEST … of Scientific...1 Cost Rs. 500 /- SCHEDULE OF TENDER...

1

Cost Rs. 500 /-

SCHEDULE OF TENDER

(ADVERTISED TENDER ENQUIRY)

ICAR–CENTRAL INSTITUTE OF POST HARVEST ENGG. &

TECHNOLOGY, PO: PAU, LUDHIANA – 141 004

Tender No. 73-1/P&S/15

Dt. 09.02.2016

For and on behalf of the Secretary, ICAR, the Director, ICAR-CIPHET invites sealed tenders under Two Bid System

(Technical and Commercial Bid) on the prescribed forms Chapter -IV and V, for the purchase of the following stores as detailed

in this schedule to tender. However, Director, ICAR-CIPHET reserves the right not to purchase any equipment.

Description of stores required Qty.

(A) MOFPI-FTL : (1) Amino Acid Analyzer (B) ICAR-National Fellow Project : (2) Fluid Bed coater/dryer (3) Membrane emulsification system (4) Multi

point stirrer (5) pH meter (6) Spray dryer (7) Main motor drive (C) DST SERB Project: (8) Compression Molding Machine (D) PHTME Testing Centre Project : (9) Dynamometer (10) Universal Testing Machine (UTM) (11) Hunter Colorimeter (12) Digital Tachometer [6 No.(3 contact type and 3 non-contact type) ] (13) Digital Hardness testing machine (Brinell type) (14) Hot Air Oven (2 nos) (15) Grain moisture meter (2 nos) (16) Digital moisture meter (17) Infrared based moisture meter (18) Fuel meter (19) Bulk Density Apparatus (20) ISI Test sieves (21) Friction and Slip Tester (22) Cone Penetrometer (Digital recording type) -2 Nos. (23) Flat bed Trolley (24) Motor operated Flat Bed Trolley (25) Spray Pattern Distribution System (26) Spray Patternator (27) Motor Operated Portable Crane (28) Sound measurement system (29) Vibration measurement system (30) Torque Measurement System (31) Metal crack detector system (32) (i) Food Grain

Silo (ii) Food Grain Silo/bin (33) (i) Centrifugal Pump Test Rig (Variable/Constant speed); (ii) Reciprocating Pump Test Rig; (iii) Pump Test Ring for centrifugal pump; (iv) Pelton Wheel Turbine Test Rig; (v) Gear Pump test Ring – One each (34) Cyclone separator (35) Tractor-Trolley (36) (i) Personal Computers (ii) I-Pad (iii) Scanner (iv) Colour Printer – One each (37) Impact Tester (38) Goniometer with computer, software and

air conditioner (E) CRP on Health Foods : (39) Vacuum oven dryer (40) Incubator-cum-shaker (41) Sonicator (42) Rotary Vaccum evaporator

AS MENTIONED

AGAINST EACH

2

2. THIS TENDER ENQUIRY HAS THE FOLLOWING CHAPTERS AND ANNEXURES:

Schedule to Tender

Chapter I : Instructions to Bidders

Chapter II : Conditions of Tender /Contract

Chapter III : Schedule of Requirement

Chapter IV : Proforma for Technical Bid

Chapter V : Proforma for financial bid

Annexure -I Performance Statement for last 3 years

Annexure-II Certificate for compliance of instructions

Annexure-III Checklist for tenders

3. You are requested to study the tender documents completely and ensure all documents and Annexures are

correctly filled in, signed and stamped where applicable and then submit your offer.

4. Tenderers are advised to carefully go through all the conditions and documents attached with this tender enquiry,

before filling in the tender. All tender documents attached with the tender are sacrosanct for considering any offer as a

complete offer. All tender documents must be duly completed, signed by authorized signatory on each page and

returned with the offer. (from Page 01 to 21)

5. This tender is not transferable.

Signature of Tenderer with office seal Sr. Admn. Officer

3

Chapter-I

Instructions to Bidders

(THIS TENDER SET IS NOT TRANSFERABLE)

1. Name of Stores : Store Section, Room No. 10

Tender Cost : Rs. 500/- (Rs. Five Hundred only) for each equipment

Those who downloaded the tender set from the ICAR-CIPHET website must submit the cost of tender through a Bank Draft/Bankers

Cheque in favour of ICAR-Unit, CIPHET payable at SBI LUDHIANA at the time of submission of tender. Tender documents submitted

without the cost of tender form will be rejected.

2. Last time & Date of Sale : 24/02/2016 upto (12.00 Noon) for S. No. 2 to 42

of Tender Document 01/03/2016 upto (12.00 Noon) for S. No. 1

3. Last Date & Time of : 24/02/2016 upto (12.00 Noon) for S. No. 2 to 42

Receipt of Tender 01/03/2016 upto (12.00 Noon) for S. No. 1

4. Time, Date & Venue of Opening : 24/02/2016 upto (12.00 Noon) for S. No. 2 to 42 in Committee Room

of Technical Bid of Tender 01/03/2016 upto (12.00 Noon) for S. No. 1 in Committee Room

5. Place of Submission of : : TENDER BOX placed in the office of the SAO Room No. 10,

Tender Documents ICAR-CIPHET, PO: PAU, Ludhiana – 141 004

i) The envelope containing tender documents must be clearly

superscribed with the Tender No., Item No., Name of Equipment, and

Date of Opening.

ii) The Institute will not be responsible for tenders submitted at any other place.

Tenders not received within the due date will not be considered under any

circumstances or for any reason.

iii) Tenderers are requested to study the tender documents completely and ensure

all documents, forms and annexure to the tender are completely and

correctly filled in, signed and stamped where applicable, all necessary

literature, brochures and pamphlets have been attached and then to submit

their offer. Incomplete tender documents shall be rejected straightway without

any reference to the tenderers. Leaving any column not filled in or with

cuttings will lead to rejection of the tender.

6. Earnest Money Deposit : Rs._______________ (Rs. ____________________________________________ only) in the

(EMD) and Validity form of crossed Demand Draft/Pay Order/Fixed Deposit receipt/Bank Guarantee in

favour of ICAR Unit CIPHET, Payable at SBI, Ludhiana from any Commercial Bank.

7. OFFER VALIDITY : 90 days from date of opening of tender.

In the absence of any indication in the tender documents submitted of the date up to

which the offer has been kept valid, it will be taken that the offer will remain open for

acceptance for the period specified in the Schedule to Tender.

8. Extension of validity & : If the validity of the tender is extended, the validity of the Earnest Money Earnest money will

also have to be suitably extended by the tenderer failing which their tender shall not be

considered by the purchaser after the expiry of the said period.

Signature of Tenderer with office seal

4

9. Eligibility for Responding : i) Only those firms should respond who are the manufacturers or authorized dealers/agents of

the stores specified in the tender specifications.

ii) The foreign manufacturers of the tendered stores will have to specify in the tender

document, details of the sales service to be provided after expiry of warranty period.

iii) Indian agents of foreign manufacturers/principal are allowed to participate in the tender

subject to the following conditions: -

a) The Indian agent will submit along with the tender documents a copy of latest authority

letter/agreement from the foreign manufacturer /principal.

b) Such agreement/authority with the foreign manufacturers/principal should be a long- term

agreement and not merely for the present tender.

c) If the agreement is only for the present tender, the offer received is liable to be rejected.

d) The Indian agent will provide details of the after sales service and post contractual support

i.e. repair, maintenance, supply of spare parts etc. that he will carry out.

e) Offers from firms whose business activities are limited to procuring items from

manufacturers, both Indian and Foreign and supplying the same to the purchaser, and having

no after sales service backup will not be entertained.

f) Where the quoting party /Indian representative claims to be subsidiary or branch office or an

authorized representative or principal foreign manufacturer /supplier in India, then a copy of

approval from RBI/Ministry concerned for operating business in India as subsidiary /branch

/liaison or joint –venture may be submitted with offer. The Indian agent of foreign

manufacturer should be enlisted with DGS&D for all items except for the prohibited items

as per the Foreign Trade Policy of Govt. of India. A copy of the current Enlistment

Certificate with DGS&D may be enclosed to the items specified for this.

g) The tenderer must submit last two years income tax return and copy of PAN Card

h) The tenderer must have latest VAT/Sales Tax Clearance certificate alongwith copy of

Registration certificate under Sales Tax.

i) The firm must have trade registration certificate

j) The tender from principal firm and authorized agent/dealer will not be accepted

together.

k) The tenderder must submit the blacklisting certificate indicated that their firm is not

blacklisted from any Govt. Organization.

10. Opening of Tender : Tendering firms can authorize a representative to be present at the opening

of the tender. The representative must bring with him a letter of authority from the firm

to be present at the opening of tender. However, in the case of Limited Tender/quotations it

is not applicable. The Limited Tender/quotations will be opened by the Committee.

10 (A) : The purchaser has the right to have a demonstration of the equipment/item in his premises. The

supplier has to abide by this condition. The demonstration has to be arranged by the supplier at

his own cost.

10 (B) : In the case of consumable materials, the firm has to provide sample(s) and in the case of

fabrication prototype has to be provided by the firm.

11. Delivery Required By : For Indian manufacturer - Within 30 days from the Date of issue of award letter or as

specified in the supply order.

For Foreign firms – 90 days from the date of opening of letter of credit (LC).

12. Terms of Delivery : For Indian\manufacturer / suppliers:-FOR ICAR-CIPHET, Ludhiana / Abohar

For Foreign manufacturer / suppliers: - On FOB/FCA Basis

13. Inspection after Receipt of Goods: The inspection will be done by the Committee in the presence of firm’s representative. The

successful tenderer will have to provide at his own cost and arrangement technically qualified

personnel at the consignee’s location for joint inspection. These personnel must be able to

unpack, assemble and demonstrate the use of the equipment fully and identified each

Part/Machines supplied. Any consumables that are essential will be provided by the supplier

free of cost.

In case of receipt of materials in damaged condition the suppliers will have to arrange

the replacement of goods free of cost. All expenses in this regard will be borne by the

supplier.

5

14. Packing & Marking : The packing and preservation of the supplied goods shall be airworthy/ seaworthy /roadworthy

(as the case may be) so that it may provide their safety during transit period. The seller shall

guarantee that the packing is strong enough to withstand the safety of the goods during

transport. The packing should satisfy the security seal in the clearing warehouse and shall carry

the fragile or other markings as required.

Each packing case shall have labels as follows:

Contract No._______________________

Consignee: Name of the

Division/Unit_________________________________


6

Purchaser: Director,

ICAR-CIPHET, Ludhiana – 141 004

All damages which may occur as a result of defective packing shall be borne by the seller.

15. Compliance Statement : The firms must submit compliance statement -cum- technical bid in the format given in

Chapter -IV failing which their offer will be treated as incomplete and is liable to be

rejected.

16. Earnest /Security Deposit : Rs.________________ (Rs._____________________________________only) to be deposited

alongwith Technical bid. in the form of Crossed Demand Draft/Pay Order/ Fixed Deposit

receipt/ Bank Guarantee in the name of the ICAR Unit CIPHET, payable at SBI Ludhiana

from any Commercial Bank. No other form of deposit will be accepted.

There will be no exemption for paying earnest money. However, Firms registered with the

Central Purchase Organization/NSIC only are exempt from submitting bids without EMD

(proof of registration must be attached therefore without which it will not be considered).

In case, therefore, if any tenderer fails to deposit the Earned Money the tender will be rejected

straightway.

EMD, Tender Fee and technical specification must be enclosed separately with

each tender item. The collectively for the same will not be considered for

consolidated item.

17. Guarantee/Warranty : Comprehensive onsite warranty is required. Warranty Terms period will start from the date of

installation of items. In case at installation stores/part of stores are found defective /damaged

during or after delivery to consignee, the suppliers will replace or repair the store under

warranty at consignee’s location in India free of cost or if any case it is required to sent back to

the foreign manufacturer. Bank Guarantee equivalent to the cost of equipment is required to be

submitted before lifting the store. All expenses in this regard will be borne by the supplier.

18. Performance Security : The successful bidder will have to submit a Performance security of equivalent to 10% of

the Contract /Order value before the issue of award letter valid till 60 days + the period of

expiry of the Warranty/ Guarantee period in shape of crossed Demand Draft/Pay order/Fixed

Deposit Receipt/Bank Guarantee from a commercial bank in favour of the ICAR Unit

CIPHET, payable at SBI Ludhiana. The performance security will remain valid till expiry of

warranty period. This will be released beyond 60 days after completion of warranty period.

19. Liquidated Damages : In case the firm does not complete the supply within the laid down agreed delivery period as

per contract, liquidated damages will be charged @ 0.5% per week or part thereof subject to a

maximum of 10% of the contract value. However, the Institute reserves the right to either

further extend or cancel the contract after expiry of delivery date and recover the liquidated

damages from the dues of the firm by legal means.

20. Dispute settlement : The dispute arising out of this contract shall be subject to the jurisdiction of Indian laws &

court at Ludhiana. Sole arbitrator is appointed by the Secretary, ICAR, New Delhi. His

decision will be final and binding to both parties (Supplier and Purchaser).

21. Submission of the proposal : The tenderers must submit the tenders in TWO BID SYSTEM

(A) TWO BID SYSTEM i) The tenderers should submit the tenders in TWO BID SYSTEM i.e. the Tenderers should

give the price bid as per Chapter -V in a separate sealed cover and the technical details/

bid as per Chapter -IV in a separate sealed cover along with detailed specifications of the

store offered supported by leaflets, Brochure, if any.

ii) Both the above mentioned cover should be sealed separately and thereafter be kept in

one big cover and again sealed.

iii) This big cover should also be superscribed with the Tender No., Stores and date of

Tender opening.

iv) Composite bid i.e. rates indicated in the technical bid openly in tender is liable to be

ignored.

v) Only the first cover i.e. Technical Bid shall be opened on the date of tender opening.

vi) Price bids of only those offers, which will be technically acceptable, will be opened

subsequently.


7

A. TECHNICAL BID

a) The FIRST COVER should contain the following:

i) Tender documents duly completed and signed but WITHOUT INDICATING THE

RATE QUOTED.

ii) The technical details of the models offered along with the supporting original technical

literature, leaflets, brochures etc. as per Chapter-IV

iii) Earnest Money

iv) Cost of tender form Rs. 500/- for each equipment if downloaded from website.

v) Details of supplies of similar equipment as per Annexure-III along with copies of supply

orders.

vi) Latest agreement /authorization from the foreign firms in case Indian agent is submitting

tender on its behalf.

vii) Trade registration certificate from the RBI/Ministry/department concerned.

viii) Last two income tax return and copy of PAN card.

ix) Latest Sales Tax clearance certificate alongwith copy of Registration

Certificate under Sales Tax.

x) Technical bulletin with specifications clearly stated with model.

B. SECOND COVER should contain the following:

i) Details of rates, taxes, duties, discounts, if any, quoted by the bidder, should be submitted as

per Chapter-V.

ii) Any documents in support of price bid.

iii) For Indian manufacturer rate should be at F.O.R. destination.

iv) For foreign supplier rates should be at FOB basis.

NOTE: a) The word “TECHNICAL BID” should be written clearly and prominently on the

first cover, name of stores and date of opening. Similarly, the word “PRICE BID” should be

written clearly and prominently on the second envelop along with, Name of Store.

b) Full name and status of the person signing the tender documents must be clearly mentioned

in the Tenders.

(B) Single Bid System The bid is to be submitted in single bid system in the case of consumable/ spares /other

goods/fabricated goods etc.

(C) Quotation/Tender unsealed or having overwriting and cutting without proper

attestation and signature will not be considered.

22. Evaluation of the Proposal : A two stage procedure will normally be adopted: -

i) Stage-I:

a) Evaluation of Technical Bids to assess their suitability against the laid down parameters.

b) Tenderers must ensure that they enclose all original technical literature and detailed

documentary proofs which specifically bring out the compliance of the equipment being

offered against the specifications. If necessary the Tenderers may be directed to give a

presentation for evaluation by a technical committee constituted for the purpose.

c) In case it is not possible to verify compliance of equipment as per technical bid due to lack

of adequate documents, in original no reference will be made to tenderer and the bid will not

be considered further and treated as cancelled.

ii) Stage-II

Financial Evaluation

a) The price bids of only those firms found meetings the laid down specifications at stage I

shall be opened, evaluated and considered further.

III) It is in the tenderers interest to include all relevant and detailed technical data as

supporting documents along with their bid.

8

23. Mode of Payment : A. FOR INDIGENOUS SUPPLIES: -

Payment on bill basis after supply, satisfactory installation, commissioning and performance of

the equipment at Ludhiana/Abohar and after certification by our Scientists concerned.

B. FOR IMPORTS: - The payment shall be made through irrevocable Letter of Credit (L.C.).

90% net FOB/FCA prices will be paid against invoice, inspection certificate (where

applicable), shipping documents etc. and balance within 21 – 30 days of successful installation

and commissioning at the consignee’s premises and acceptance by the consignee. Entire 100%

agency commission will be paid after all other payments have been made to the supplier in

terms of the contract. Payment to the Indian agent will strictly be made in Indian rupees after

satisfactorily commissioning of equipment.

All bank charges outside India will be borne by the supplier. In case the delivery date of the

contract is extended to take care of delay in supply, for which the suppler is responsible, the

tenure of the letter of credit so extended, the expense incurred therefore such extension is to be

borne by the supplier.

24. A legal agreement/contract shall be executed with the contractor/firm by the Institute before installation of all/any type of

instrument/machine as per the instructions of the Indian Council of Agricultural Research (ICAR).


9

25. Training : THE TENDERERS SHALL PROVIDE TRAINING TO THE USER AS PER

THE TERMS & CONDITIONS OF THE CONTRACT AS HAS BEEN

SPECIFIED IN TECHNICAL & FINANCIAL BIDS FREE OF COST AT THE

TIME OF INSTALLATION/COMMISSION OF EQUIPMENT AT THE

CONSIGNEES/ USERS LOCATION. AS SPECIFIED BY THE PURCHASER.

ALL EXPENSES IN THIS REGARD WILL BE BORNE BY THE SUPPLIER.

26. Insurance : As applicable in the case of imported goods.

For indigenous item it will be responsibility of the supplier to supply the

material in good condition on FOR basis without involving the risk of the

purchaser.

CHAPTER-II

CONDITIONS OF TENDER/CONTRACT

1. All annexures, attached with the Tender should be duly filled in and supported with requisite documents for considering any offer as

a complete offer.

2. Director, ICAR-CIPHET, Ludhiana, reserves the right to cancel/reject any or all the tenders without assigning any reason.

3. Director, ICAR-CIPHET, Ludhiana, also reserves the right not to purchase any equipment mentioned in the tender.

In case of open tender form downloaded from website tenderers must enclose Demand Draft of tender cost Rs. 500/- (Rs. Five

Hundred only) in favour of ICAR Unit CIPHET payable at SBI, Ludhiana for each equipment. The tender received without required

Bank Draft shall be rejected.

4. EARNEST MONEY DEPOSIT:- EMD of Rs._________ (Rs. __________________________________ only) must be deposited in

the form of crossed Demand Draft/Pay Order / fixed deposit receipt/ Bank Guarantee in favour of ICAR Unit CIPHET payable at SBI,

Ludhiana from any Commercial Bank. No other form of deposit will be accepted. Technical bid without supported with earnest

money, therefore will be rejected.

There will be no exemption for paying earnest money. However, Firms registered with the Central Purchase Organization/NSIC only

are exempt from submitting bids without EMD (proof of registration must be attached therefore without which it will not be

considered).

a) No interest shall be payable by the purchaser on the EMD deposited by the tenderer.

b) The EMD deposited is liable to be forfeited if the tenderer withdraws or amends impairs or derogates from the

tender in any respect within the period of validity of his tender.

c) If the successful tenderer fails to furnish the performance security as required in the contract within the stipulated

period, the Earnest Money shall be liable to be forfeited by the purchaser.

d) EMD of the unsuccessful tenders shall be returned after finalization of tender.

5. The firm must supply the user list and latest client satisfaction certificate of the equipment to the IIT’s, IISC and ICAR

Institutes, otherwise tender will not be considered.

6. GUARANTEE/WARRANTY

I. Except otherwise provided in the invitation to tender the contractor hereby declares that the

goods/stores/articles/equipment sold/supplies to the purchaser/consignee under this contract shall be of best

quality and workmanship and new in all respects and shall be strictly in accordance with the specification and

particulars mentioned/contained in the contract. The contractor hereby guarantees that the said

goods/stores/articles would continue to confirm to the description and quality aforesaid for a period of Twenty

Four months from the date of receipt of goods/articles/equipment in good condition at site by the consignees in

case of supply contract and Twenty Four months from the date of installation and satisfactory taking over of the

goods/stores/articles/equipment at site by consignee where installation and commission is involved and

notwithstanding the fact that the purchase /inspection authority has inspected and/or approved the said

goods/stores/articles equipment or such if during the 24 months the said goods/stores/articles/equipment be

discovered not to confirm to the description and quality aforesaid or not giving satisfactory performance or have

deteriorated and the decision of the purchase /consignee in that behalf shall be final and biding on the

contractor/seller and the purchaser shall be entitled to call upon the contractor/seller to rectify the

goods/stores/articles/equipment or such specified period as may be allowed by the purchaser in his discretion

10

on application made thereof by the contractor/seller, and in such an event, the above period shall apply to the

goods/stores/articles/equipment rectified from the date of rectification mentioned in the warranty thereof,

otherwise the contractor/seller shall pay the purchaser such compensation as may arise by reason of the breach

of warranty therein contained.

II. Guarantee that they will supply the spare parts, if and when required on agreed basis for an agreed price. The

agreed basis could be and including but without limitation an agreed discount on the catalogue price or an agreed

percentage of profit on landed cost.

III. Warranty to the effect that before going out of production for the spare parts they will give adequate advance

notice to the purchaser of the equipment so that the later may undertake the balance of lifetime requirements.

NOTE: - In case of any discrepancy in the period of guarantee/ warranty mentioned anywhere else in this

Tender document, the stipulations as mentioned in the chapter III (specification of the equipment/ item to

be purchased ) would prevail.

7. Price: - The price quoted shall be on firm and fixed basis and should be reasonable living no scope for any further

negotiation on price.

A. For goods manufactured in India: - on FOR basis (including all kind of charges and taxes)

i) Installation commissioning charges, if any

B. For goods manufacture abroad: - The price of the goods should be quoted on FOB basis excluding the Indian

agent commission if any.

Installation commissioning charges, if any

The Institute is exempted from payment of excise duty. Hence, excise duty will not be paid to the firm.

Sales tax we are not authorized to issue Sales Tax Form C&D;

The Institute is exempted from payment of Custom Duty

7 (A) AMC of Equipment: After the warranty/Guarantee term is over, the firm should mention the charges of AMC atleast for first three

years.

NOTE: - In case of any discrepancy in the period of and/or AMC mentioned anywhere else in this Tender document,

the stipulations as mentioned in the chapter III (specification of the equipment/ item to be purchased) would

prevail.

8. Penalty for use of undue influence:-

The seller should undertake that he has not given offered or promised to give directly or indirectly any gift,

consideration, reward, commission, fees brokerage of inducement to any person in service of the Purchaser or

otherwise in procuring, the contract or forbearing top do or for having done or for borne to do any act in relation or

execution of the contract or any other contracts with the Institute for showing or for bearing to show favour or

disfavor to any person in relation to the contract or any other contract in the ICAR-CIPHET. Any breach of the

aforesaid undertaking by the seller or any one employed by him or acting his behalf whether with or without the

knowledge the seller or the commission of any offers by the seller or any one employed or acting on his behalf, as

defined in Chapter-IX of the IPC, 1860 or the Prevention of Corruption Act, 1947 or any other Act enacted for the

Prevention of Corruption shell entitle the purchase to cancel the contract and all or any other contract with the

Institute seller and recover from the seller the amount of any loss arising from such cancellation. A decision of the

purchaser or his nominee to the effect that a breach of the undertaking had been committed shall be final and

binding on the seller.

Giving or offering of any gift, bribe or inducement or any attempt at any such act on behalf of the seller towards

any officer /employee of the purchaser or to any other person in a position to influence any officer /employees of

the purchaser for showing any favour in relation to this or any other contract sell render

9. LAWS GOVERNING THE CONTRACTS : - The contracts shall be governed by the laws of India for the time

being in force. The contract shall be interpreted in accordance with these laws.

10. Jurisdiction of Court: - The court of the Ludhiana shall have a Jurisdiction to decide any dispute arising out of

or in respect of contract.

11. Force Majeure Clause : - The Supplier shall not be liable for forfeiture of its performance security, liquidated

damages or termination for default, if and to the extent that, it’s delay in performance or other failure to perform

its obligations under the Contract is the result of an event of Force Majeure. For purposes of this Clause, “Force

Majeure” means an event beyond the control of the Supplier and not involving the Supplier’s fault or negligence

and not foreseeable. Such event may include, but are not limited to, acts of the Purchaser either in its sovereign

or contractual capacity, wars or revolutions, fires, floods. Epidemics, quarantine restrictions, strikes, lockout or

any act of war. Notice of the happening of any such event is given by either party to the other within 15 days

from the date of occurring thereof. However either party at its discretion can terminate the contract in such

cases.

11

12. Termination of contracts:- Time shall be the essence of the contract. The purchaser shall have the right to

terminate the contract without any notice in part or in full in any of the following cases.

a) The delivery of the material is delayed for causes not attributed to Force Majeure after the scheduled date of

delivery.

b) The seller is declared bankrupt or becomes insolvent.

c) The delivery material is delayed due to causes of Force Majeure by more than reasonable time.

d) In case Performance Security is not furnished within the time period specified by the purchaser.

Supply in the case of successful Tenderer should strictly confirm to the specifications of the equipment being

purchased.

Any change in Address /Telephone/Fax/e-mail of the tenderer should immediately be informed. The state of non-

communication by the firm will make the offer liable for rejection.

13. The successful bidder will have to provide the original proforma invoice from the foreign principal (duly signed in

ink), in case of imported item/equipment, within 15 days of the date of receipt of purchase order, otherwise the

purchase order will automatically stand cancelled without any further communication.

14. Govt. Regulations: - It shall also be confirmed that there are no Govt. restrictions or limitation in the country of

the supplier or countries from which sub-components are being procured and/or for the export of any part of the

system being supplied. Supplies/Contracts shall provide a certificate this effect.

15. Late /Delayed tenders shall not be considered at all. These will be returned to the firm as it is at their expenses.

Post tender revision/correction shall also not be considered.

16. Acceptance or rejection of offer: - The Director, ICAR-CIPHET, Ludhiana reserves the right to accept or reject

any tender in part or full without assigning any reason thereof. The successful bidder should submit order

acceptance letter within 10 days from the date of issue.

17. Page Numbering & Signatures: - Every page of the tender must be numbered and signed by the authorized

signatory giving his/her name and designation below the signature.

18. In case of imported equipments, the tenderer will have to submit Tax Residency Certificate and no

permanent establishment in India certificate. If there is permanent establishment in India, then bidder will

have to pay TDS as per rules.

Signature of Tenderer with office seal Sr. Admn. Officer

12

Chapter-III

ICAR-CIPHET, Ludhiana

Specification of the equipment / item (in detail) to be purchased.

1

2

3

4

5

6


13

Chapter-IV


TECHNICAL BIDS

(To be sealed in separate Cover)

Specification of the equipment / item(in detail) to be purchased.

S.N

Details of Technical Specifications

Whether

complied

with

YES/NO

If yes, please

attach Tech

literature of the

equipment duly

printed &

clearly specify

page No of

Bulletin which

specifically

confirm this

If no, attach

deviation

statement

Remark

s (if any)

N.B.:- All the bidders are requested to provide true statement in the columns. Concealing of facts will liable to be

rejected the tender completely. No communication will be made in this regard.

All the bidders are requested to submit the copies of all the supporting documents separately if they are

participating in more than one equipment.


14

Chapter-V


PROFORMA FOR PRICE BID

(Compulsory to be filled up with details by the bidder& sealed in

separate cover)

S.

No

Details of Specifications Rate/Unit Net Price

1.

2.

3.

4.

5.

6. Optional accessory

I) Ex factory price offer (excluding agency commission, to be

invariably separately shown and if nothing is claimed reasons thereof

must be indicated failing which the bid will not be considered)

II) Training Cost, if any

Packaging & handling charges

FOB Price excluding agency commission

Any payment to be paid in Indian Rupees towards agency commission,

supply of Indian made item and other charges like VAT /S.T.

Name of items: -

1.__________________________________

2.__________________________________

3.__________________________________

4.__________________________________

VAT + S.T.__________________________

Total

*Components to be supplied locally to be clearly indicated.


15

Annexure-I

PERFORMANCE STATEMENT FOR LAST 3 YEARS Must be enclosed of all the quoted equipments, otherwise the tender will not be

considered.

S.

No.

Name of the

items

Name of the

office by whom

order was placed

Order No. &

date (Please

enclose copy

of supply

orders)

Value of

supply

order

Delivered in

time or not

If not

please

specify

the

reason

Attach

satisfactory

working

report from

each office

(Yes/No)


16

Annexure-II

CERTIFICATE TO BE SIGNED BY THE TENDERER

CERTIFICATE

It is certified that I have read and understood and will comply all instructions contained in tender

enquiry and its schedule. All pages of schedule to tender from page ____________________ to

___________________ have been filled properly and signed.

Signature of tenderer: -_____________________

Name in block letters: _____________________

Name of firm:_____________________________

Full address:______________________________

______________________________

______________________________

______________________________

i) Telephone No._______________________

ii) Mobile No.__________________________

iii) Fax No._____________________________

iv) Email id____________________________

v) Website____________________________


17

Annexure-III

Check list for Tenderers

Before submission of tender documents, Tenderers should check they have complied with the following

requirements: -

Sl. No. Requirements to be checked before submission of the tender Compiled

(Please indicate)

Yes after

complying with the

requirement)

1. Cost of Tender has been enclosed with tender document, if downloaded from website. If not, then

supporting documents proving exemption to this enclosed.

2. Earnest money Deposit (EMD) has been enclosed.

3. Copy of valid enlistment certificate with DGS&D in the case of Indian Agent enclosed only in case

the bid is for item falling in the restricted list of the Export & Import Policy of Govt. of India.

4. Copy of trade registration certificate from the RBI /Ministry or department concerned in the case

of foreign subsidiary firm

5. Enclose sales tax registration certificate and PAN No.

6. Complete tender documents have been enclosed, after signature & stamping on ALL pages.

7. Signatures of witness with full name and address have been added whenever required on tender

document.

8. Proposal has been submitted in two bid systems – Technical Bid & separate price Bid as per tender

enquiry.

9. Offer validity as required in tender has been accepted & clearly mentioned in tender document.

10. Delivery Terms & Period as per tender have been accepted and mentioned in tender.

11. Payment Terms as per tender have been accepted and mentioned in tender.

12. Compliance statement as per chapter-IV has been enclosed along with supporting technical

documents /proof for each point/parameter clearly showing it is complied with or not.

13. Performance statement for 3 years as required in tender, in the laid down format as per annexure-I,

has been enclosed. If not, reasons to be specifically given in writing.

14. Warranty terms as per tender accepted.

15. Annexure-II regarding compliance of all conditions mentioned in the tender form has been

enclosed.

16. Status of tenderer has been clearly written in tender – manufacturer or manufactures authorized

agent. If authorized agent, valid latest agreement authority letter/agreement for the stores quoted

from the manufacturer has been enclosed.

17. Free Training on use of equipment after supply, as specified tender, has been accepted in writing.

18. Technical and financial bid along with necessary documents have been sealed in separate envelops

and both envelops again sealed in a big envelops with prescribed writing on envelops.

19. The tenderer has clearly mentioned in writing that business dealings with their firms have not been

banned by any Govt./Private agency.

20. If the tenderer wants to mention any specific condition, it must be mentioned on the

covering/forwarding letter only which will be placed on the first page of the technical bid. Such

condition mentioned in any other document shall not be given any consideration.

21. The tender from principal firm and authorized agent/dealer will not be accepted together.


18

Specification of the equipments

Sr. No Name of Equipment

Specifications No.

1. Amino Acid

Analyser

An automatic computer controlled ultra fast high performance

liquid chromatography system equipped with a suitable

quaternary gradient solvent delivery system with Auto sampler,

Column compartment, PDA Detector, Florescence Detector &

Data acquisition, preferably with both pre-column and post-

column derivatization assembly and setup for hydrolyzing,

purifying and concentrating food sample (Cereals, pulses,

oilseeds) before injecting into the system.

Gradient pump

Should be capable of working in Gradient operation (up

to 4 solvents) with quaternary pump

Should provide error free programming of pump

parameters including flow rates, operating pressure

limits, compressibility compensation, calibration and

diagnostics.

Online vacuum degasser for gradient operation

Programmable flow rate range: 2.0 ml/min or better

Max. operating pressure: 15000 or better

Flow precision: 0.075% RSD or less

Flow rate accuracy: ±1.0% or better

Dwell volume: < 400µL

Automatic Piston Seal washing or purging facility should be

available

The pump should have GLP features like maintenance

feedback for continuous tracking of instrument usage with

user settable limits and feedback messages

Auto sampler

Injection volume range : 0.1-10µL or more

Auto dilution & reagent transfer facility should be

available in sampler

Auto sampler with Heating (4-40 Degrees C in 0.1ºC

increment) & cooling facility

Auto sampler carryover should not be more than

0.005% RSD or better

Sample delivery precision <1.0% RSD or better

Should accommodate up to 25-100 samples

capacity or more, microplates and/or Standard vials

of 2 mL

Injection Needle Wash: Integral, active and

programmable

Fluorescence Detector

Wavelength Range: 200 – 900 nm or better (may include

photomultiplier)

Bandwidth: 20 nm or better

Wavelength Accuracy : ± 3 nm or better

19

Wavelength Repeatability: ± 0.25 nm or better

Sensitivity: S/N> 800 or more

Light Source: Hg/ Xe Lamp

Flow cell volume: 4 μL or less

Data Acquisition Rate : Upto 80 Hz or more

Photo Diode Array ( PDA) Detector

Wavelength range: 190–800 nm or better

Light source: Pre-aligned Deuterium lamp

Wavelength accuracy: +/-1 nm or better

Optical resolution : 1.2 nm or better

Peak purity software should be provided

Flow cell volume: 4 μL or less

Data acquisition rate: Upto 80 Hz or more

Column Oven

Column Temp Control: 20ºC to 80ºC or better

Temperature increment: 0.8ºC or better

Column Tracking: Electronic column information

management tracks and archives usage history

Column Temp Stability: ±0.3ºC or better

Compartment Temp Accuracy: ±0.5ºC or better

Column dimensions:Column oven should be able to

accommodate 30 cm column

Columns

C18 Analytical Column (5Micron) suitable for amino acids,

mycotoxin/ aflatoxins and vitamins– 02Nos

C18Analytical Column (2-3 Micron)-02Nos

C-8Analytical Column (5Micron)– 01Nos

All compatible accessories including Kit/cell necessary

for mycotoxins/aflatoxins analysis

Accessories and software

All accessories (including sample loops, online filters, tubings

etc.) toolkits, connections and original software to control and

operate the whole Instrument

All genuine spare parts necessary for smooth functioning of the

system should be provided

Operating Manuals

System compatible amino acid analysis kit (Minimum 100

Samples)

Kit should include standards (20 amino acids), reagents,

derivatizing reagents, tubing’s, column and solvents etc.

required for derivatization and amino acid analysis.

Sample purification kit

Sample purification kit for amino acid analysis from food matrix

(Cereals, Pulses, Oilseeds)

Supply of pre-maintenance kit

Operating conditions (Environmental)

Operating temperature range: 4.0 to 35.0 °C or better

Operating humidity range: 20% to 70% or more

20

Power requirements: 100 to 240 V AC; frequency 50 Hz or

better

Computer

Branded Dell /HP/ Lenovo/IBM Desktop computer with

original windows software (7 or higher) having Core i5

or better processor, 4GB RAM, 500GB Hard disk. DVD-

RW Drive

HP Laser printer

Online 5 KVA UPS with 30 min or more back up

Warranty

2 years of warranty from the date of installation should be

provided with the system

Training of minimum three scientists in handling and trouble

shooting of the Equipment at the supplier lab’s at company

expenses

Free of cost visit of company application expert/engineer

for method development and establishing the amino acid

analysis technique in the Institute under the warranty

period

Customer satisfactory performance certificate from

minimum 5 user of Government institutions/organisations

with installation in last 5 year

Optional

AMC for 3 years after expiry of warranty

C18 Analytical Column (5Micron) suitable for amino acids,

mycotoxin/ aflatoxins and vitamins– 02Nos

Setup for hydrolyzing, purifying and concentrating food

sample (Cereals, pulses, oilseeds) before injecting into the

system 2. Fluid Bed

coater/dryer Fluid Bed processor (a) Batch Size : 200 gm or more (up to 1 kg).

(b) Product Container : Useful volume : above 200 ml Container should be made of

transparent plastic/SS316L grade or better quality. Preferrably with portion of toughened

glass/ transparent plastic to ensure visibility of process.

(c) Spray Nozzle: Binary (Two Fluid) nozzle for atomizing liquids with nozzle aperture

size 0.4 to 1.0mm.

(d) Controls & Display : Air pressure, filter blowing pressure and temperature.

(e) Filter Cleaning: By air purging / blowing.

(f) Peristaltic Pump & Compressor : The equipment has to be supplied peristaltic pump and

compatible air compressor.

(g)Power: A/C Single/3 phase220–240V 50Hz

(h) Warranty / Extended Warranty : 03 (three) years from the date of installation and final

acceptance

(i) User list, at least two contact details of users who can vouch for satisfactory and

continuous performance of fluid bed processor for last two years (without these the offer

may become invalid).

Test runs with food components at ICAR-CIPHET.

(j) Bidder to specify space, wattage and other utilities required

(k) GMP Compliance Preferable.

(l) Optional(with separate price):

i) Spray congealing accessory to cool molten material with cool or chilled air

ii) If bottom and top spray accessories are available, one of them to be quoted as

optional item

01

21

3. Membrane

emulsification

system

Membrane emulsification system S.S. 316 Mounted Module with S.S. Housing fitted with inlet and outlet pressure indicator

suitable for Tubular ceramic/glass membranes with suitable pump for emulsification of fats

using microfiltration membranes.

Membrane area: 0.4 - 0.5 m2

Membranes (preferably monoporous)

Glass/Ceramic tubular : 0.2 Micron Quantity: One



Warranty / Extended Warranty : 02 (two) years from the date of installation and final

acceptance

The bidder should provide other accessories like wall or piping system for individually

controlling testing units.

Test runs at ICAR-CIPHET.

Optional items: (with separate prices)

i) Completely hydrophobic MF membranes of sizes as mentioned above (to

pump oil through membrane in to water on outside for making oil in water

emulsion to encapsulate functional food ingredients)

ii) spare tubings and pressure gauges etc suitable for above module

01

4. Multi point

stirrer

-For stirring 5 or 6 beakers or flasks simultaneously without heating

-Temp.: ambient to 100°C

-Speed range : 0 – 1200 rpm

- speed control: 10 rpm steps

-Stirring quantity max. per stirring position : 300-500 ml water

Warranty / Extended Warranty : 03 (three) years from the date of installation and final

acceptance


The bidder or his principal should have manufactured and supplied at least 10 such

systems (IITs, IISc, NITs, IISERs).

Performance certificates from at least two of above users (with contact details of users who

can vouch for satisfactory and continuous performance for last two years). Without these

the offer may become invalid.

01

5. pH meter Bench top pH meter

pH Measuring Range: -2.000 to 20.000

pH resolution: 0.001

Temp range -10 to 100 degrees

pH accuracy +/- 0.002

Calibration Points: five points

8 predefined and 1 user defined Buffer groups

Automatic Buffer recognition

Automatic, Manual & Timed endpoints format

Password protection for System settings, Login & deletion of data

Data storage of up to 1000 measurements

GLP compliant print formats

Sensors should be available with chip based memory for auto recognition and

storing calibration data

Certified IP54 for dust and water protection

Connectivity with computer for data storage

Optional sensor should be available for measuring pH in micro volumes like PCR

tubes, NMR vials,96 well plates for volumes as low as 5 µl (separate prices for all

optional items)

Optionally additional electrode to be quoted

22


acceptance


The bidder or his principal should have manufactured and supplied at least 10 such systems

(IITs, IISc, NITs, IISERs). Performance certificates from at least two of above users (with

contact details of users who can vouch for satisfactory and continuous performance for last

two years). Without these the offer may become invalid.

6. Spray dryer Benchtop/table top spray dryer

Capacity 100–500 ml/h

Temp. range of Inlet air 30°C–300°C

Control accuracy ± 1°C

Feed pump 30–2000 ml/h

in steps of 1% of pump capacity

controlled through PLC.

Consumption of dryer air 20–100 m3 /h

Spray system two fluid nozzles

Spray direction downwards co-current

Power A/C Single/3 phase220-240V 50Hz

Auto deblocking provision with variable timing


acceptance

GMP Compliance

Test runs with maltodextrin solution at ICAR-CIPHET.

Performance certificates from users (IITs, NITs, IISERs) with at least two contact details of

users who can vouch for satisfactory and continuous performance of benchtop spray dryer

for last two years (without these the offer may become invalid).

Optional: Spray congealing accessory to cool molten material sprayed with cool or chilled

air (with separate price)

01

7. Main motor

drive Main motor drive to run different attachments

Main motor : 1 hp or less

Variable Speed : 0-400 rpm

Electronic/plc based control

It should be able to run different attachments such as pan coater, double cone

mixer, piston type homogenizer (for making emulsions)

A/C Single/3 phase 220-240V 50Hz

Bidder to specify space, wattage and other utilities required.


acceptance

Optional items of compatible capacities for small lab scale i.e. up to 1 kg per batch (with

separate prices):

i. pan coater

ii. double cone mixer

iii. piston type homogenizer


The bidder or his principal should have manufactured and supplied at least 5 such systems.

Performance certificates from at least two of above users (with contact details of users who

can vouch for satisfactory and continuous performance for last two years). Without these

the offer may become invalid.

01

8. Compression

Molding

Machine

Compression Molding Machine, both plates heated and cooled

Capacity/ Clamp Force: 20 to 50 tons

Plate size: 10” x 10” to 30” x 30”

Heated plates Between 100 to 400C with electric heatings digital PID temperature

controllers and Programmable ramping controllers, Air-cooled heat exchanger

Audible or visual alarms, Automatic transition from closing to pressing speed, Clamp area

01

23

guards with keyed interlock

Closing speed 70 IPM (approx.)

Contact gauge for quieter & more energy efficient operation

Digital display of clamp force, Electrically / Motor Operated

Electronic force control, Extended tie rods

Extra heat zones in platen(s), High speed hydraulic package

Low pressure system, Lower sliding platens, Mechanical eject

Mold heat temperature controllers and plugs, Power operated safety gate (in lieu of

standard manual gate

Pressing speed 5 IPM, Pressing speed control, Pressure relief valve with analog pressure

gauge, Shuttle platens

Tilting platens, Water cooled platens,

Work table, Pressure adjustment valves

Easy accessibility for quick maintenance

Appropriate for bio-composite sheet making and plastic sheet making.

Internally Reputed manufactures such as Wabash etc

9. Dynamomet

er

Max. Power 20-25KW/4000 to 12000RPM Max. speed @1200RPM = 1.5 BHP Max.

Torque 95N-m@1000 to 2000 RPM

The dynamometer should supply with water filter with magnetic separator - A pressure

switch, Suitable for absorbing and measuring power in both direction - Load cell weaning

mechanism

Standard Mechanical Accessories - Universal engine mounting test bed type, Cardan shaft

with guard, Dynamometer calibration kit - Magnetic pickup, Gravimetric fuel consumption

meter

Latest performance certificates from reputed institutes like IITs/NITs and other highly

reputed institutes

01

10. Universal

Testing

Machine

(UTM)

Universal Testing Machine (UTM)

Dual Column, Electromechanical universal testing machine suitable for testing tensile,

compression and flexural/ Peel testing etc. of polymers and composites, metal, concrete

blocks with or without an environmental testing chamber.

Universal Testing Machine capable to work up to 50kN on different load cells such as 2, 5,

10, 25, 30, 50 kN Load force capacities etc.

100:1 force range (i.e. use the load cell to 1.0% of capacity with no loss of accuracy)

Load accuracy of 0.5% of indicated load

500Hz data acquisition rate (appropriate compatible software)

100Hz data acquisition rate (appropriate compatible software as per company policy)

Automatic transducer recognition

Appropriate vertical test space

Computer Interface Via USB or Ethernet, Full software control, Application Software

Suitable and should be compatible with OS or Controlled by PC Must be there

Optional grips and fixtures

Optional temperature chambers but must work at Room Temperature.

Along with one 2 Ton AC with digital, remote control and stabiliser of standard make

companies.

10KVA power backup system for at least one hour of reputed company.

Latest performance certificates from reputed Institutes like IITs/NITs and other highly

reputed Institutes.

01

11. Hunter

Colorimeter

Handheld Colorimeter, about 30 mm port size; 20-30mm viewed area,

d/8 (diffuse) or 45/0 optical geometry,

30 mm to 3.0 mm measurement area,

Fully portable, one-handed operation, customisable LCD display, With 45°/0° or diffuse/8°

geometry and large area or small area view,

Displays color data, color difference data, color plot, spectral data, spectral data difference,

spectral plot, spectral difference plot, Includes all commonly used color scales and indices

Averages up to 20 sample readings

Stores: 100 standards and 800 sample measurements,

Operating Environment: 5° to 40°C, 10 % to 90 % RH, Storage Environment: -20° to

65°C, 10 % to 90 % RH.

Suitable for a wide range of sample types, fabrics, paper, powders, granules and liquids

01

24

when measured through a sample cup.

Latest performance certificates from reputed institutes like IITs/NITs and other highly

reputed institutes

12. Digital

Tachometer

Combination Contact/ Laser Photo Tachometer

Range (rpm) : 2 to10, 000 or more rpm (photo mode/contact mode)

Resolution: 0.1-0.5 rpm (< 10,000 rpm); 1-2rpm (> 10,000 rpm)

Sampling Time: 0.5- 1.0 Sec > 120-140 rpm

Accuracy: 0.05- 0.1% rdg +1 digit (photo mode/contact mode)

06 (3

contact

type

and 3

non-

contact

type)

13. Digital

Hardness

testing

machine

(Brinell

type)

Max. Load, kgf : 150, Load range, kgf: 10, 60,100,150, Initial load, kgf: 10

The testing machine confirms to IS 2281-1968 for Brinnel, Digital Hardness

testing machine, Automatic load selection, manual operation with facility of

brinnel test. With standard accessories and LCD display

01

14. Hot Air

Oven

Internal Chamber Size: approx. 600 x 600 x 900 mm

Temperature Range: up to 250°C, Housing Triple walled chamber required,

Inner and outer chamber should be made of stainless steel sheets. Inter

space in between the walls should be tightly packed with special grade glass

wool. ILS Trays / sleeves- 3 to 4 (stainless steel trays), Door Insulated

double walled door with smooth locking arrangements at the front.

Power Supply: Single / Three phase, Temperature Accuracy: ± 1 °C,

Temperature controller: Digital temp. Indicator cum Controller with

Thermocouple Timer and alarm arrangement required

Warranty: 2 years

02

15. Grain

moisture

meter

Measurement Principle: Capacitance (Di-electric)

Product calibrations: Wide variety of seed and grains

Sample volume: 200-300 ml

Measurement Range: 1-5%

Response time: Instant

Accuracy: ± 0.5%

Resolution: 0.1 - 0.2%

Temperature: 0-50°C

Humidity: 0-90%

Display: Backlit LCD

02

16. Digital

moisture

meter

Measurement Range: 5 – 100 %

Response time: Instant

Accuracy: ± 0.5%

Resolution: 0.1 - 0.2 %

Temperature: 0-50°C

Humidity: 0-90%

Display: LCD

01

17. Infrared

Based

moisture

meter

Moisture Range 0% to 100%

Measuring Accuracy of Moisture: 0.5-1.0 % Amount of Samples ≥ 0.5- 1.0

g

Weight of Measurement Samples: Up to 60 g

Readability of Moisture: 0.01- 0.02 %

Temperature Indication Ranges: Room Tempera ture to160°C

Temperature of the Sample: -40°C to 50°C

Temperature of the Working Environment: -5°C to 50°C. Relative

Humidity: ≤ 80% R.Η

Power Supply: 220 v± 10% Frequency 50 Hz ± 1Hz or so.

01

18. Fuel meter Capacity: 1 to 50 l/h with motor having capacity upto 80 kW;

Measurable Parameters: Total fuel consumption, Instant fuel consumption,

Engine operating time in various mode (idling, optimal, Overload); Display-

Electronic; protection from unauthorized interference and tampering

01

19. Bulk

Density

Bulk Density Apparatus Display: 4 digit seven segment Bright Red LED

Maximum Counts: 9999

25

Apparatus

Keyboard: 6 Soft Touch Membrane Keys

Cylinders: 2 Nos. 50/100 MI Cylinders

Drop Height: 25 mm. Approx.

Power: 230 V 10 % AC 50 Hz

Dimensions: 600×450×200 mm (Approx.) (L×B×H)

Accessories: 50 ml Cylinders - 2 Nos., Instruction Manual & Dust Cover etc

01

20. ISI Test

sieves

Frame Dia.: 8 inches

Particle Size Range: 20 µm to 40 mm

Motion: Vibratory

No. of Sieves: 12 sieves and one pan

Electric Volts: 230 V/ 50 Hz.

Material of sieves: Brass

Test sieves opening size: 20, 40, 63, 125, 250, 500 µm & 1, 2, 4, 10, 25, 40

mm

Motor Operated

Noiseless

01

21. Friction and

Slip Tester

Advanced features for measuring Automatic calculation of static and kinetic

coefficient of friction. Selectable speed from 5 to 40 cm per minute or more.

Selectable travel distance from 5 to 25 cm, Load cell: 10 newtons or so,

Digital display, storage and editing of up to 100 readings, selectable units

(COF or grams), Settable limits Statistics-average, standard deviation,

high/low results. Report printout with built in printer Graph Master ,

compatible output, Static/kinetic coefficient of friction calculated in one

operation. Direct drive arm with unique skid control Sled-connecting

mechanism ensures level pulling action.Large color display shows all results

and settings. Optional heated platen available. Measure the sliding

resistance of sheet like materials including plastic film, packaging film

laminates, paper, paperboard and coated surfaces. Paper, Flexible

Packaging, Foils, Rubber, Plastics, Wood, Linoleum, Metal, Printing,

Coatings, Composites. Includes calibration fixtures.

01

22. Cone

Penetromete

r (Digital

recording

type)

Measurement depth range: minimum 80 cm

Parameter to be measured : Depth, penetrator resistance force

Measuring accuracy : ±1%

Required all Accessories and software.

02

23. Flat bed

Trolley

Capacity, kg: 1000; Size platform(feet) (Body): Minimum 10 x 6 x 2 ft

Size of chassis: 3750 X 850 mm or higher

Size of axle: 75 x 75 mm square bar

Suspension: Leaf spring 42”[70 x 13 mm main leaf and 70 x 11

mm assembly] or strong

Platform floor MS sheet: 4 mm MS sheet

Side panel: Heavy duty box type 2.5 mm MS sheet ; Rim (disc): Center plate

lock ring type heavy duty; Tyre size: 9.00 x 20; Hydraulic cylinder capacity,

ton: 10; Braking system: As per Automotive Industry Standard (AIS) 043

with provision of service & parking brake

01

24. Motor

operated

Flat Bed

Trolley

Product Size: 1500x1000x1100 or less

Plate Size: 1300 x 1000 mm or less

Plate height: 300 mm or less

Maximum capacity: 500 kg

Motor operated

01

25. Spray

Pattern

Distribution

System

Test rig sprayer & Hand pump sprayer As per BIS Standard ; mounted on M.S.

Structure duly powder coated. The Unit Comprises of

M.S. Frame Stand with pressure gauge accumulator; Suction & discharge pipe ;

a. Sum Tank & measuring Tank, 1 HP DC motor of 1500 rpm with dimmerstat

arrangement for attaching pressure assembly to Knapsack / Hand pump Tank ;

Digital counter for stroke measurement ; Sprayer Pump ; Pressure Gauge ; Main

Switch

Test rig for foot and rocker sprayer As per BIS Standard; mounted on M.S.

01 set

26

Structure duly powder coated. The Unit Comprises of

Foot & Rocker pump on MS Frame; Pressure gauge accumulator; Suction pipe

& discharge pipe ; Sum &Measuring Tank ; Main Switch 1 HP D.C. Motor ; 4A

Dimmer State ; Hand valve arrangement for changing pump ; Stop clock; Strap

drop.

Tank impact test rig As per BIS Standard; mounted on M.S. Structure duly

powder coated. The Unit Comprises of ;

M. S. Metallic Fabricated Frame ; Double acting pneumatic Cylinder's 3 No. ;

Canti Lever Assembly ; Belt Assembly ; Test tank Assembly ; Limit switch ;

Pressure gauge ; Flow Control Valve ; Electro Pneumatic Solenoid Valve with

Air Compressor ;

Test rig for Fatigue on compression sprayer As per BIS Standard; mounted on

M.S. Structure duly powder coated. The Unit Comprises of ;

M.S. Fabricated Stand with air Compressor single cylinder single phase ; Air

filter Solenoid Valve, Three way valve, Limit switch ; Pneumatic cylinder ;

Digital counter with timer Pressure Gauge; Three separate line for three Nozzle

Test Rig for Trigger Type cut off device As per BIS Standard ; mounted on M.S.

Structure duly powder coated. The Unit Comprises of ;

M.S. Fabricated Frame 1000 X 700 X 1500 approx ; Air Compressors Single

Cylinder Single Phase;Pragmatic Cylinder ;Pressure Regulator ; Pressure Gauge

; Limit Switch ; Electrical Cut Out (6A) Solenoid Switch ;Spray Nozzle ; Unit

with Powder Coated ; STP pump with pipe Assembly.

Nozzle performance test rig. As per BIS Standard; mounted on M.S. Structure

duly powder coated.The Unit Comprises of;

M. S. Fabricated Stand Assembly ; M.S. 'V' channels Spray collecting

Assembly. glass test tube 18 No. with Oil seals for collecting spray water. ;

Rota meter (Water) Acrylic Body.

LPM 100 ; Glass test tube tiling assembly ; STP spray Nozzle ; pressure gauge.

Fabricated Structure App. Size = 900 X 700 • 1200 MM.

Spray launce pressure test rig As per BIS Standard ; mounted on M.S. Structure

duly powder coated. The Unit Comprises of;

M. S. Fabricated Stand Assembly; 1 HP DC Motor 4 A, DC Dimmer Assembly ;

Cam and Flange Assembly ; Connecting rod Assembly ; Electrical Switch ; Air

Foot Pump.

Reciprocating Pump test bench As per BIS Standard; mounted on M.S.

Structure duly powder coated. The Unit Comprises of;

Reciprocating Pump of 1 HP single phase 1500 rpm with 4A dimmer stat ;

Vacuum Gauge at suction line ; Pressure Gauge at Discharge line Measuring

input to electric Motor by Energy meter, ; Output of Pump performance can be

estimated at three different speed by using pulley; Recirculation type unit ; M.

S. Stand Assembly Measuring Tank of Size : 500 x 400 x 400mm with FRP

Coated ; M.S. sum Tank 900 x 600 x 600mm

Test set up of mist blower; mounted on M.S. Structure duly powder coated. The

unit comprises of;

Round type duct ; Pitot Tube ; U Tube manometer ; Blower switch ; Single

phase 1 HP centrifugal blower Leakage.

Test for delivery line; mounted on M.S. Structure duly powder coated. It is

comprises of:

1 HP HTP Pump 3 phase 1500 rpm Motor with starter ; Air compressor

assembly Air filter ; Pressure gauge regulator with pressure gauge Pneumatic

cylinder ; Solenoid Valve, limit switch ; Nozzle sprayer assembly Sum Tank

Hand valve ; Separate line for leakage purpose.

26. Spray

Patternator

Patternator/ Patternation: Mechanical / digital, Tables to evaluate the liquid

distribution provided by a nozzle or array of nozzles. collect the sprayed

material at many locations across the spray plume and the level of each

collection bin is recorded.

01 set

27

Spraying nozzles: 5 to 10, provision to adjustable flow rate, height and

width. Appropriate image frame for measuring droplet/ particle size,

Droplet Velocity, volume Flux, Volume Distribution, Spray Angle, Droplet

Shape, Spray Impact, etc.

Test rig for Fatigue on compression sprayer As per BIS Standard. The Unit

Comprises of SS/MS Fabricated Frame 1000 X 700 X 1500 approx. Foot &

Rocker pump mounted on Frame; Pressure gauge accumulator; Suction pipe

& discharge pipe; Sum &Measuring Tank; Main Switch 1 HP D.C./AC

Motor; Hand valve arrangement for changing pump; Stop clock.

Strap drop and tank impact test rig As per BIS Standard. Limit switch;

Pressure gauge; Flow Control Valve; Electro Pneumatic Solenoid Valve Air

Compressor

27. Motor

Operated

Portable

Crane

Capacity: 10 TON or higher

Type: Four cylinder diesel engine, water cooled. Engine Power: Min.45

BHP@2200RPM

Transmission: Heavy duty, sliding mesh type gear box with 6 forward and 2

reverse speed ; Travel speed: without load 25 kmph

Clutch: Heavy duty friction type, single plate

Fuel Tank: about 45 litre; Hoist mechanism: Four fall, hydraulic winch and

rope diameter

13 mm or so. Power steering; Standard accessories: All weather cabin, front

Bumper, lift cylinder guard, turn & reverse lamp and other optional

accessories

01

28. Sound

Measuremen

t System

Sound level meters OLED display

Calibration prompt for compliant, accurate measurements Simultaneous

measurement of all key noise parameters

20dB(A) to 140dB(A)

Dynamic measurement range

01

29. Vibration

Measuremen

t System

Display 3-1/2 digit LCD with bar-graph

Frequency range 10Hz to 1KHz (frequency sensitivity meets ISO -2954)

Sampling time one (1) second approx.

Data output Isolated PC Interface

Data Hold Freezes displayed reading

Min/Max Memory Meter stores highest and lowest readings for later recall

Data Logger Store up to 500 readings

Data logger Sample Time 0 (manual), 1, 2, 5, 10, 30, 60, 600, 1800 and

3600 sec.

Pickup thread size 10-32 UNF

Auto Power OFF Meter automatically shuts off after 10 minutes of

inactivity

Low battery indication Battery symbol appears on the LCD

Power supply 9V Battery

Power consumption 8mA DC approx.

Operating Temperature 0 to 50oC

Operating Humidity: 80% RH

Dimensions Meter: 180 x 72 x 32mm (7.1 x 2.8 x 1.3")

Probe: 18mm (0.75”) diameter x 40mm (1.6”)

Functions: Acceleration (RMS or Peak)/Velocity (RMS or

Peak)/Displacement (Peak to Peak)

Vibration Severity: 0.5 to 199.9 mm/s

Accuracy: ±5 % + 2 digits

01

30. Torque

Measuremen

t System

Shaft Dia: 5 inch, Capacity 50000 Nm, least Count 20 Nm. Shaft Dia: 4

inch, Capacity 5000 Nm, least Count 5 Nm.

Excitation Voltage 10 VDC Max.15 VDC

Nominal output 2.0 mV/V

Non-linearity < ± 0.2% FSO

Non- Repeatability < ± 0.1% FSO

Creep(30minutes) < ± 0.5% FSO

Zero Balance ± 2.0% FSO

01 set

28

Input Resistance 390 Ohms

Output Resistance 350 Ohms

Insulation Resistance (50 VDC) >1000 Mega Ohms; Cable Length ( 4 Core

Screened) 5 Mtr.

Safe Overload 150% of RC

Ultimate Overload 200% of RC

Temp. Compensated Range 0-60º C

Temp. Effected on output < 0.0015% FSO/C

Temp. Effected on Zero < 0.020% FSO/C

Rotational Angular Deflection < 0.2 at FSO

Finish & Construction Shaft Mounted

Environmental Protection IP 65 – Gauge Area

RPM Max 1000

DATA ACQUISITION SYSTEM

Channel 4 Channel; Accuracy 1%; Interface RS 232Port;

31. Metal crack

detector

system

Magnetic crack detector machine 4000 Amps. HWDC with S.S

Tank, Digital Meter.

Mode: Automatic (Auto clamping, Magnetic, Spray, De-clamp)

Machine is suitable for disc dia up to 900 mm & thickness

approx 20 mm.

Shaft dia up to 150 mm & length up to 3000 mm. Cycle time 6 -

8 second and UV-LED light Assy.

With required standard accessories and installation & testing of

Machine

01

32. Food Grain

Silo

1) Food Grain Silo: Made of Galvanized sheet of 120 GSM GI Sheet for inside

and 275 GSM GI Sheet for outside; Capacity: 2000 kg, Long term storage

Legs of MS pipes/channel suitably reinforced with angle iron/pipe bracing

Discharge height of about 1250 mm, aeration system, Electrically operated

discharge gate, Vertical bucket elevator of matching height. With Bag stacker

for loading and unloading of filled bags in trucks, containers and godowns etc.

01

2) Food Grain Silo/bin: Made of Galvanized sheet of 120 GSM GI Sheet for

inside and 275 GSM GI Sheet for outside; Capacity: 2000 kg, Long term

storage

Legs of MS pipes/channel suitably reinforced with angle iron/pipe bracing

Discharge height of about 1250 mm, aeration s ystem, Electrically operated

discharge gate, Vertical bucket elevator of matching height. With dryer of

indirect heating type

Includes centrifugal/axial fan for Uniform/even drying, Thermostatically

controlled temperature, Oil burner (Automatic) with sensi tive thermostat,

solenoid valve and sequence controller; Drying bin dimension: 1900 mm Dia. ×

2742 mm Length. Blower Capacity 11000 at 20 mm WGSP

Blower Motor Power 3 HP

01

33. Centrifugal

Pump Test

Rig

(Variable/C

onstant

speed);

Reciprocatin

g Pump Test

Rig; Pump

Test Ring

for

centrifugal

pump;

Pelton

Wheel

1) Centrifugal Pump Test Rig: Centrifugal pump:-1”x1” size,

Motor – Variable Speed P.M. D. C. motor with conforming to ISI and of

reputed brand; Speed Controller for Motor. Sump tank: 950x450x450 mm or

so; Measuring Tank: 450x350x450 mm or so; Energy meter for motor input

measurement. Pressure & vacuum gauge for measurement of head.

Good quality Stop watch; Floor space of 1 m. x 1 m. Electricity: 230V AC,

50 Hz.

01

2) Reciprocating Pump Test Rig: Reciprocating pump:-3/4” x 3/4” size

provided with 1 H.P. D. C. Motor & speed controller with conforming to ISI

and of reputed brand, Sump tank- 950x450x450 mm or less, Measuring

tank-450x350x450 mm or so. Energy meter for motor input measurement,

Pressure & vacuum gauge for measurement of head. Good quality Stop

watch Floor space: 3mx3m, Electricity : 230V AC , 50 Hz.

01

3) Pump Test Ring for centrifugal pump: Series & Parallel ,Pump (2

units) Type: centrifugal pump; Maximum head : 22 m H2O; Maximum flow :

01

29

Turbine

Test Rig;

Gear Pump

test Ring

90-100 LPM ; Circulation Tank Cylindrical, transparent tank Volume : 20 -

25 L ; Pressure gauge Delivery side: 0 to 12 bar Suction side : -1 to 6 bar;

Rotameter Size : 1” Range : 0 to 160 LPM

4) Pelton Wheel Turbine Test Rig: Steel Tank: 128cm × 92cm × 2.0cm;

Motor – Pump, single-Phase, 5.5/7.5 KW/HP Motor -27/42 m Head, 910/630

lpm Discharge, Centrifugal Pump; Flow-meter; With Readout meters;

Turbine/pump – Motor Set; Gun Metal Packing With Rope and Lip Seal

01

5) Gear Pump test Ring: Pump: Speed 1500 RPM (Max.) Capacity 1HP,

Head 5kg/cm2 (max.) Medium Flow : Clear oil Drive : 1HP DC Motor with

Thyristor controlled DC Drive for variable speed Sump Tank : Capacity 35

Ltrs(approx.) Flow measurement : Using Measuring Tank (capacity 20 Ltrs),

and Electronic Stop Watch Pressure Gauge : Bourdon type Vacuum Gauge :

Bourdon type Tanks made of : Stainless Steel Control Panel comprises of:

RPM measurement : RPM Indicator with Proximity sensor Energy

measurement : Electronic energy meter On/off switch Mains indicator etc

With good quality painted rigid MS Structure.

01

34. Cyclone

separator

Cyclone separator : Material Stainless Steel, Dia- 100 mm

Solid discharge Silo: Material Stainless Steel, suitable capacity with

discharge control valve.

Blower: ID Fan Blower with 1 HP provided motor

Air flow measurement: Flow meter with manometer

Solids collector: Transparent PVC container fixed with cyclone

Fine dust collector: Bag of Nylon cloth fixed on exit of air

Control panel comprises of

Standard make On/Off switch, Mains indicator etc.

01

35. Tractor-

Trolley

Four Wheeled, Hydraulic Tractor Trolley, Measurement approximately-

Length of trolley: 3700mm, Width of trolley: 1800mm, Height of doors:

500mm

Bottom plate: 6mm thick or more

Side door Plate: 3mm thick

Axel: 100mm x 100mm thick

Wheel Plates: 8mm thick

Tyre Size: 7.50 x 16; Hydraulic Cylinder for lifting trolley with help of

tractor; Capacity: 10-20 tons, appropriate attachment to attach to tractor etc.

From repute manufactures.

01

36. Personal

Computers

All-in-One (3rd Gen Ci5 or 7/ 4GB/ 500GB/ Win8) may be with 1GB Graph ics

card, keyboard, mouse etc. More than 2.7 GHz with Turbo Boost up to 3.20

GHz, Display Size more than 21 inch or so. LED Display, DVD Writer,

Wireless IEEE 802.11b/g/n, connectivity ports such as VGA, USB, microphone -

in, headphone-output, HDMI, PS2, HWTV in, TV in and AV in, gigabit

Ethernet jack and wireless connectivity options like Bluetooth and Wi-Fi etc.

Computer should of reputed company. Also have 1KVA backup UPS of reputed

company.

01

I-Pad Retina display 9 to 10 inch (diagonal) LED backlit Multi Touch display with

IPS technology 2048 by 1536 resolution at 264 pixels per inch (ppi),

Fingerprint-resistant oleophobic coating, 64GB or 128GB; Weight-400 to 500g,

A8X or so chip with 64‑bit architecture and M8 motion coprocessor, Fully

laminated display; Antireflective coating, Wi‑Fi + Cellular,

Fingerprint identity sensor, Cameras: Face Time HD camera of 1.2MP photos;

720p HD video, Face Time video calling over Wi-Fi or cellular3, Face

detection, Backside illumination; iSight camera: 8MP photos, Autofocus; Face

detection, Backside illumination; Five-element lens, Hybrid IR filter; ƒ/2.4

aperture, HDR photos, Panorama; Burst mode, Video Recording (1080p HD):

Tap to focus while recording, Video stabilization, Face detection, Backside

illumination 3x video zoom, Time-lapse video, Slo-mo video, Battery Life: Up

to 10 hours of surfing the web on Wi-Fi, cellular data network, Charging via

01

30

power adapter or USB to computer system, Colour: White/ silver/gold. From

reputed company.

Scanner Fast & Convenient, compatible with computers. Red Eye Removal, Hi Speed,

Compact Design, Duplex ADF Scanner with Flatbed, Fastest, most feature rich

scanner in its class, 23 ppm/46 ipm in b/w, 200 dpi mode, OneTouch scanning

with Acuity, Searchable PDF file creation, Robust full version software

bundle, Power Supply, USB 2.0 Cable, Quick Install Card, Technical Support

Card, DVD-ROM (PC Software), Scanner Drivers etc.

01

Colour

Printer Printing capacity of 8 A-4 ppm in colour and 12 ppm in black. Resolution of

600 x 600 dpi with print capacity of 1400 papers per cartridge. The printer

holds a maximum input capacity of 150 sheets of A4 size and comes with 96

MB inbuilt and 342 MB upgradeable memory. It has a USB port, one 144 -pin

DDR 2 DIMM slot and memory card slots that supports cards like SD, MMC,

CF, XD and Memory stick. Reputed company models.

01

37. Impact

Tester

Model : Digital Model

Confirms to Standard : ASTM D 256 & ASTM D 6110, ISO 180 & ISO 179

Pendulum Impact Energy : 0-25 Joules

Least Count of Indication : 0.1 Joules

Release Angle of Pendulum : 150⁰

Striking velocity range of

Pendulum : 2.5 – 3.5 m/s.

Accessories : Standard detachable weights corresponding to (2J, 4J, 7J,

15J,and 25J)to obtain the desired test range. Standard fixtures for fitting

Izod /Charpy test and other standard accessories.

Auto Notch Cutter & Sample : Suitable for notching plastics specimens for

Izod &

Mounting accessories Charpy impact tests. As per ASTM D 256, D 6110

and ISO 180, ISO 179

Power : 230V, 50Hz, Single phase

Range of 4 seaters : 0-2.71J Resolution 0.02J

0-5.42J, Resolution 0.05J

0-10.84J Resolution 0.10J

0-21.68J Resolution 0.20J

0-25.0 Resolution 0.20J

01

38. Goniometer

with

computer,

software

and air

conditioner.

Goniometer equipped with image analysis software to measure contact

angle: Measuring position of the luminaire: Normal position, Positioning

accuracy: ϕ < 0.02°, δ < 0.05°; Repetitive accuracy: ϕ < 0.01°, δ < 0.02°

Material Aluminium, coated with preferably black pa int; Drives and control

Jetter Servo drives; Gears High precision Harmonic Drive and Cyclo gears;

Size of measuring object: ≤ 1500 mm (luminous area); Space required:

LxWxH = ≤ 2700 x 2700 x 3200 mm³; Travel path: ϕ = 0° ... 360°

δ = 5° ... 352° (hanging test object support)

δ = -174.5° ... 172.5° (upstanding test object support

Both DLS and SLS modes: Correlation & Intensity Measurements; Large

angular Range: 8° to 155° with 25mm cells: 15° to 155° with 12 mm cells.

Fine Adjustment Control: Read angle to 0 .01° directly on large, fine-control

adjustment knob.

Temperature Control: Heating and cooling via any standard external

circulator Separate temperature and filtration plumbing. Special Design

Glass Vats: Specially polished and flat entrance window ensures minimum

flare. Alignment Cell: Fine-screw vertical adjustment makes finding the

center of rotation easier.

Multiple Laser Line Filters: Filter wheel with 632.8 (HeNe), 514.5/488.0 nm

(Ar+), one open position for weak scatterers, and 2 blank (shutter)

positions. Also available with 532 nm bandpass filter.

Variety of Cell Holders: High precision cell holders standard, low-priced

round cells available: 27.5 mm dilution vials fit cell holder sleeve. Special

small-volume cell available.

01

31

39.

Vacuum oven

dryer

Laboratory Model Vacuum Oven Dryer

Total Capacity: 25-30 liters.

Operating temperature: Room temp.+5°C to 240°C

Temperature Control accuracy: ±1.0°C

Operating pressure range: inch Hg ( -3.0 to -29.9)

kPa (-10 to -101)

mbar (-101 to -1010)

Display: Digital LED/LCD Display with Back-Light Function

No. of shelves: 2/3

Control System: Programmable Microprocessor PID

Temperature Set and Display Sensitivity: 0.1ºC

Power Supply: AC 220 V, 50 Hz

Vacuum Gauge Reading Sensitivity: 0.05 bar

Vacuum chamber: stainless steel

Safety Viewing Window

Analogue pressure display

Stainless steel vacuum fittings

Upper limit for oven and product protection

Separate temperature control

Pressure controller with solenoid valve

24 hour timer

Storage Function: Alarm & Timer.

Safety Device: Over Temperature, Over Current Protector,

Sensor Error Detector, Leakage Breaker

Vacuum Pumps, Direct Drive & Oil Sealed Rotary vane type (silent type)

Optional:

Inert gas connection for precise release of non-flammable, nontoxic gases

(VDI 2046) with precision valve and overpressure safety valve

Additional options (Data control software and RS 232 interface) for

pressure and temperature documentation Stainless steel shelf

Two years on-site extended warranty on all parts

01

40. Incubator-

cum-shaker

PID Control: Microprocessor based PID Controller.

Internal Chamber: Stainless Steel 304 grade.

External : Mild Steel Powder Coated

Volume (approx.): 200-250 Ltr

No. of shelves: 3 (adjustable)

Maintenance-free brushless motor

Temperature Range: About 3°C above ambient to 65°C

Temperature Accuracy: +/-0.5 degree C approx. of set value for Temp.

Uniformity : +/-1 degree throughout chamber

Air Circulation: Motorized Blower from back and forced air circulation for

temperature homogenicity.

Should have PUF Insulation

Display: LED/LCD

Triple eccentric drive for long life and smooth, quiet operation

Standard orbit of 25mm for higher oxygen transfer rate

Adjustable shelves for simultaneous incubation with and without shaking

Safety Devices:

1) Motor stops when door is opened

2) Heater turns off in case of over-heating

3) In case of power failure, after restoration of power, shaking

automatically resumes from the point when it last stopped

Speed: 30 to 400 rpm, programmable, continuous or a timed run consisting.

Flask capacity: variable from 50 ml to 2 lt flasks

Should have door operated illumination lamp to work on 220 VAC.

Inner Full Size See through Acrylic/Plexi glass

Sterile chamber consisting of fluorescent or Ultra violet lamp to provide

illumination

Should be supplied with Stabilizer of sufficient capacity.

Wheel mounted for easy portability.

01

Page 24 of 27

32

Applicable certifications such as CE/BIS/TUV/GMP and other relevant

national and international certification for components are required.

Necessary accessories and tool kit should be supplied.

Should come with 2 years warranty.

41. Sonicator

Basic unit comprising :

1. Flow cell: Made up of stainless steel

2. Probe of different sizes to sonicate minimal volume

3. Heater facility upto 80oC

4. Digital temperature indicator cum controller

5. Pulse (1s-60s) sweep energy and auto degassing facility

6. Auto temperature cut-off function

7. Output Frequency >20 kHz

8. Sound proof chamber

9. Digital display and control

10. Power : 700W

Accessories:

1. Minimum spares including cleaning solution

2. SS Basket and lid

01

42. Rotary

Vaccum

evaporator

Specifications

Capacity: up to 20 liters evaporation capability 2 -5 L/h(water) and

5-10L/h (alcohol)

Achievable Vacuum range 350 Pa and upto 1 atm.

Vacuum chamber water bath made of stainless steel

Speed 20-250 rpm. Working temperature upto

100o C. Automatic temperature and Pressure controllers.

variable frequency output. Step-less speed regulation with precise control.

Digital LCD Display

compatible Power Supply

Safety Devices.

Sensor Error Detector, Leakage Breaker

Vacuum Pumps, vaccum PTFE Sealed Rotary type

01

ICAR CENTRAL INSTITUTE OF POST HARVEST … of Scientific...1 Cost Rs. 500 /- SCHEDULE OF TENDER...

Documents

Transcript of ICAR CENTRAL INSTITUTE OF POST HARVEST … of Scientific...1 Cost Rs. 500 /- SCHEDULE OF TENDER...