Hkkjrljdkj&jsyea=ky; Government of India – vuqla...
Transcript of Hkkjrljdkj&jsyea=ky; Government of India – vuqla...
Amend-1 of TC-119 (Rev.-1) Page 1 of 2
lR;esot;rs
Hkkjrljdkj&jsyea=ky;
vuqla/kkuvfHkdYivkSjekudlaxBu
y[kuÅ& 226011 e-mail: [email protected] Telephone : 0522-2465716
Government of India – Ministry of Railways Research, Designs & Standards Organization, LUCKNOW – 226011 Telex: 0535-2424 RDSO-IN Fax: 91-0522-2465716
No. EL/4.2.15/Gen Date: 25.08.2017
M/s. Medha Servo Drive Pvt. Ltd, P-4/5B, IDA Nacharam, Hyderabad – 76
M/s. IC Electricals Company (P) Ltd. 156, DSIDC, Okhla Industrial Area, Phase-1, New Delhi – 110 020
M/s. Stone India Limited, 16, Taratalla Road, Kolkata – 88
Sub: Ammendment no. 1 of Technical circular no. RDSO/2012/ EL/ TC/119 Rev-1 dated 20.3.2013 for implementing bilingual display of fault messages in Microprocessor based Control & fault diagnostic System (MPCS).
1. Railway Board vide their letter no. 2008/Elect (TRS)/113/5 dated 26.12.2016 had advised RDSO to make suitable modification in MPCS software to ensure bilingual display of fault messages for ease of troubleshooting by the crew.
2. Accordigly, RDSO had prepared amendment-1 of TC-119, which amends Table -1 of TC 119 which specifies faults messages and action to be taken by crew.
3. Details of fault messages and action to be taken by crew are defined in ammended Table-1 of the Technical circular no. RDSO/2012/EL/TC/119 Rev-1. The fault messages and action to be taken by crew will be displayed both in English & Hindi.
4. Technical circular no. RDSO/2012/EL/TC/119 Rev-1 along with amendment-1 specifies the technical details of MPCS version-3 with specification no. ELRS/SPEC/MPC-FDS/0001 Rev.-3.
5. It is advised to modify the software and implement the amended Table-1 of TC 119 with in 3 months in MPCS version-3.
(P. K. Saraswat)
Encl: as above For Director General/Elect. Copy to: 1. Secretary (Elect.), Railway Board, Rail Bhawan, New Delhi- 110 001 (Kind attention: Sri A. K. Goswami DEE/RS/RB): For kind information please.
Amend-1 of TC-119 (Rev.-1) Page 2 of 2
2. Chief Electrical Engineers:
Chittaranjan Locomotive Works, Chittaranjan-713 331 (WB) Central Railway, Mumbai, CST-400 001. East Central Railway, Hazipur-844101. East Coast Railway, Chandrashekharpur, Bhubaneshwar-751016. Eastern Railway, Fairlie Place, Calcutta-700001. North Central Railway, Subedarganj, Allahabad. Northern Railway, Baroda House, New Delhi-110001. South Central Railway, Secunderabad-500 071. South East Central Railway, Bilaspur-495004. South Eastern Railway, Garden Reach, Calcutta-700 043. Southern Railway, Park Town, Chennai-600 003. West Central Railway, Jabalpur-482001. Western Railway, Churchgate, Mumbai-400 020
For kind information please.
(P.K. Saraswat)
Encl: As above For Director General/Elect.
Page 1 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Table -1: Details of Fault Messages and action taken
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Main Power Circuit
1 DJ Tripped Via QOP – 1
DJ Tripped Via QOP – 1
Fault
Earth Fault in power circuit-1
1st Check other safety relays
QRSI-1, QRSI-2 & QLM...If there is QLM follow local instructions.
If there is no QLM, reset QOP-1 target & resume normal traction.
vU; ls¶Vh fjys QRSI-1, QRSI-2,oa
QLMdh tkWp djsasaA ;fn QLM Mªki
gks rkss LFkkuh; vuqns”kksa dk ikyu
djsasaA
;fn QLM Mªki ugha gS rkss] QOP-1 ds
VkjxsV dks fjlsV djsasa ,oa lkekU;
VSªD”ku pkyw djsasaA
QOP-1 }kjk DJ fVªi 2nd
If HMCS-1 at position 1. Isolate faulty TM by HMCS-1.
If HMCS-1 not on position 1, put HQOP-1 on position 0. Follow local instruction.
;fn HMCS-1 dh iksth”ku ^1* ij
gSa rkss] nks’k iw.kZ eksVj dks HMCS-1
ls i`Fkd ¼vkblksysV½ djsasaA
;fn HMCS-1 dh iksth”ku ^1* ij
ugha gSa rkss HQOP-1 dks ‘0’ vFkkZr
vkQ ij djsasa ,oa LFkkuh; vuqns”kksa dk
ikyu djsasaA
Main Power Circuit
2 DJ Tripped Via QOP – 2
DJ Tripped Via QOP – 2
Fault Earth Fault in power circuit -2
1st Check other safety relays
QRSI-1, QRSI-2 & QLM.If there is QLM follow local instructions.
If there is no QLM,reset QOP-2 target & resume normal traction.
vU; ls¶Vh fjys QRSI-1, QRSI-2 ,oa QLM dh tkWp djsasaA ;fn
QLM Mªki gks rkss LFkkuh; vuqns”kksa
dk ikyu djsasaA
;fn QLM Mªki ugha gS rkss QOP-2
ds VkjxsV dks fjlsV djsasa ,oa lkekU;
VSªD”ku pkyw djsasaA
QOP-2 }kjk DJ fVªi 2nd
If HMCS-2 at position 1. Isolate faulty TM by HMCS-2.
If HMCS-2 not on position 1, put HQOP-2 on position 0. Follow local instruction
;fn HMCS-2 dh iksth”ku ^1* ij
gSa rkss] nks’k iw.kZ eksVj dks HMCS-2
ls i`Fkd ¼vkblksysV½ djsasaA
;fn HMCS-2 dh iksth”ku ^1* ij
ugha gSa rkss] HQOP-2 dks iksth”ku
‘0’ vFkkZr vkQ ij djsasa ,oa LFkkuh;
vuqns”kksa dk ikyu djsasaA
Page 2 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Main Power Circuit
3 DJ Tripped Via QRSI –1
DJ Tripped Via QRSI –1
Fault
Over Current in Rectifier block-1
1st Check others safety relays
QOP-1, QOP-2 & QLM.If there is QLM follow local instructions.
If there is no QLM then reset QRSI-1 and. Reclose DJ. Resume normal traction
vU; ls¶Vh fjys QOP-1, QOP-2 ,oa QLM dh tkWp djsasaA ;fn
QLM Mªki gks] rkss LFkkuh; vuqns”kksa
dk ikyu djsasaA
;fn QLM ugha Mªki gS rkss QRSI-1
dks fjlsV djsasa] DJ dks Dykst djsasa ,oa
lkekU; VSªD”ku pkyw djsasaA
QRSI-1 }kjk DJ fVªi 2nd
If DJ trips again isolate faulty motor through HMCS-1.
In case fault persists put HMCS-1 back to position 1 and put HVSI-1 on 0. Resume normal traction and work with half power.
;fn iqu% DJ fVªi gksrk gS rkss
HMCS-1 dh lgk;rk ls nks’kiw.kZ
VSªD”ku eksVj dks i`Fkd ¼vkblksysV½
djsasaA
;fn lQyrk ugha feyrh gS rkss
HMCS-1 dks okil ^1* ij djsasa ,oa
HVSI-1 dks ^0* iksth”ku ij djsasa rFkk
gkQ VSªD”ku ikoj ls VSªD”ku pkyw djsasaA
Main Power Circuit
4 DJ Tripped Via QRSI –2
DJ Tripped Via QRSI –2
Fault
Over Current in Rectifier block-2
1st Check others safety relays
QOP-1, QOP-2 &QLM. If there is QLM follow local instructions.
If there is no QLM then reset QRSI-2 and RecloseDJ. Resume normal traction
vU; ls¶Vh fjys QOP-1, QOP-2 ,oa QLM dh tkWp djsasaA ;fn
QLM Mªki gks] rkss LFkkuh; vuqns”kksa
dk ikyu djsasaA
;fn QLM Mªki ugha gS rkss QRSI-2
dks fjlsV djsasa] DJ dks Dykst djsasa rFkk
lkekU; VSªD”ku pkyw djsasaA
QRSI-2 }kjk DJ fVªi 2nd
If DJ trips again isolate faulty motor through HMCS-2.
In case fault persists put HMCS-2 back to position 1 and put HVSI-2 on 0. Resume normal traction and work with half power.
;fn iqu% DJ fVªi gks tkrk gS rkss
HMCS-2 ls nks’kiw.kZ VSªD”ku eksVj
dks iFkd ¼vkblksysV½ djsasaA
;fn lQyrk ugha feyrh gS rkss
HMCS-2 dks ^1* ij djsasa rFkk
HVSI-2 dks ^0* iksth”ku ij djsasaA
gkQ VSªD”ku ikoj ls VSªD”ku pkyw djsasaA
Page 3 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Main Power Circuit
5 DJ Tripped Via QLM
DJ Tripped Via QLM
Fault Primary circuit Over Current
Check Transformer / GR Oil splashing. Check other safety Relays alsoAsk for relief loco.
If there is no oil splashing follow local instruction.
QLM }kjk DJ fVªi VªkalQkeZj ,oa VSi psUtj vk;y
QSyk ¼LIyS”kM½ gksus dh tkWp djsasaA
vU; lqj{kk fjys dh tkWp djsasaA ;fn
vk;y QSyk gS rkss lgk;rk yksdks dh
ekax djsasaA
;fn vk;y QSyk ¼LIyS”kM½ ugha gks rkss
LFkkuh; vuqns”kksa dk ikyu djsasaA
Main power circuit
6 ICDJ through QOP-1 ICDJ through QOP-1
Fault Earth fault in power circuit-1
1st Check other safety relays
QRSI-1, QRSI-2 & QLM.If there is QLM follow local instructions.
If there is no QLM, reset QOP-1 target & resume normal traction.
vU; lqj{kk fjys QRSI-1, QRSI-2 ,oa QLM dh tkWp djsasaA ;fn
QLM Mªki gks rkss LFkkuh; vuqns”kksa
dk ikyu djsasaA
;fn QLM Mªki ugha gS rkss QOP-1
dks fjlsV djsasa ,oa lkekU; VSªD”ku pkyw
djsasaA
QOP-1 }kjk ICDJ 2nd
If HMCS-1 at position 1. Isolate faulty TM by HMCS-1.
If HMCS-1 not on position 1, put HQOP1 on position 0. Follow local instruction
;fn HMCS-1 dh iksth”ku ^1* ij
gSa rkss] nks’k iw.kZ VSªD”ku eksVj dks
HMCS-1 dh lgk;rk ls i`Fkd
¼vkblksysV½ djsasaA
;fn HMCS-1 dh iksth”ku ^1* ij
ugha gSa rkss] HQOP-1 dks ‘0’ vFkkZr
vkQ ij djsasa ,oa LFkkuh; vuqns”kksa dk
ikyu djsasaA
Page 4 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Main power circuit
7 ICDJ through QOP-2 ICDJ through QOP-2
Fault
Earth fault in power circuit-2
1st Check others safety relays
QRSI-1, QRSI-2 & QLM. If there is QLM follow local instructions.
If there is no QLM, reset QOP-2 target & resume normal traction
QOP-2 }kjk ICDJ vU; ls¶Vh fjys QRSI-1, QRSI-2 ,oa QLM dh tkWp djsasaA ;fn
QLM Mªki gks] rkss LFkkuh; vuqns”kksa
dk ikyu djsasaA
;fn QLM Mªki ugha gS rkss QOP-2
fjys dks fjlsV djsasa ,oa lkekU; VSªD”ku
pkyw djsasaA
2nd
If HMCS-2 at position 1. Isolate faulty TM by HMCS-2.
If HMCS-2 not on position 1, put HQOP2 on position 0. Follow local instruction
HMCS-2 dh iksth”ku ^1* ij gks
rkss] HMCS-2 dh lgk;rk ls nks’k
iw.kZ VSªD”ku eksVj dks i`Fkd
¼vkblksysV½ djsasaA
;fn HMCS-2 dh iksth”ku ^1* ij
ugha gSa rkss] HQOP-2 dks ‘0’ vFkkZr
vkQ ij djsasa rFkk LFkkuh; vuqns”kksa dk
ikyu djsasaA
Main power circuit
8 ICDJ through QLM ICDJ through QLM
Fault Primary circuit over current
Check Transformer / GR Oil splashing Check other safety Relays also. Ask for relief loco.
If there is no oil splashing follow local instruction.
QLM }kjk ICDJ VªkalQkeZj ,oa VSi psUtj vk;y
QSyk ¼LIyS”kM½ dh tkWp djsasaA vU;
lqj{kk fjys dh tkWp djsasaA ;fn
vk;y QSyk gS rkss lgk;rk yksdks dh
ekax djsasaA
;fn vk;y QSyk ¼LIyS”kM½ ugha gks rkss
LFkkuh; vuqns”kksa dk ikyu djsasaA
Page 5 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Main power circuit
9 ICDJ via QRSI-1 ICDJ via QRSI-1 Fault QRSI-1 N/C interlock open
1st Check others safety relays
QOP-1, QOP-2 &QLM. If there is QLM follow local instructions.
If there is no QLM then reset QRSI-1 Reclose DJ. Resume normal traction
vU; ls¶Vh fjys QOP-1, QOP-2 ,oa QLM dh tkWp djsasaxs] ;fn
QLM Mªki gS] rkss LFkkuh; fu;eksa
dk ikyu djsasaxsA
;fn QLM Mªki ugha gS rkss QRSI-1
fjys dks fjlsV djsasaxsA iqu% DJ Dykst
djsasa ,oa lkekU; VSªD”ku pkyw djsasaA
QRSI-1 }kjk ICDJ 2nd
If DJ trips again isolate faulty motor through HMCS-1.
In case fault persists put HMCS-1 back to position 1 and put HVSI-1 on 0. Resume normal traction and work with half power.
;fn iqu% DJ fVªi gks rkss HMCS-1
dh lgk;rk ls nks’kiw.kZ VSªD”ku eksVj
dks iFkd ¼vkblksysV½ djsasaxsA
;fn lQyrk ugha feyrh gS rkss
HMCS-1 dks ^1* ij okil djsasaxs
vkSj HVSI-1 dks ^0* ij djds gkQ
VSªD”ku ikoj ls lkekU; VSªD”ku pkyw
djsasaA
Main power circuit
10 ICDJ via QRSI-2 ICDJ via QRSI-2 Fault QRSI-2 N/C interlock open
1st
Check others safety relays QOP-1, QOP-2 & QLM.If there is QLM follow local instructions.
If there is no QLM then reset QRSI-2 and RecloseDJ. Resume normal traction
vU; ls¶Vh fjys QOP-1, QOP-2 ,oa QLM dh tkWp djsasaxs] ;fn
QLM Mªki gS] rkss LFkkuh; fu;eksa
dk ikyu djsasaxsA
;fn QLM Mªki ugha gS rkss QRSI-2
fjys dks fjlsV djsasaxsA iqu% DJ Dykst
djsasa ,oa lkekU; VSªD”ku pkyw djsasaA
QRSI-2 }kjk ICDJ 2nd
If DJ trips again isolate faulty motor through HMCS-2.
In case fault persists put HMCS-2 back to position 1 and put HVSI-2 on 0. Resume normal traction and work with half power.
;fn iqu% DJ fVªi gks rkss HMCS-2
dh lgk;rks ls nks’kiw.kZ VSªD”ku eksVj
dks iFkd ¼vkblksysV½ djsasaxsA
;fn lQyrk ugha feyrh gS rkss
HMCS-2 dks ^1* ij okil djsasaxs
vkSj HVSI-2 dks ^0* ij djds gkQ
VSªD”ku ikoj ls lkekU; VSªD”ku pkyw
djsasaA
Page 6 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Main Power circuit
11 DJ not holding due to Low/No OHE
DJ not holding due to Low/No OHE
Wait for OHE and follow local instructions.
uks OHE@ yks OHE
}kjk DJ gksYM u gksuk
OHE dh izrh{kk djsasa ,oa LFkkuh;
vuqns”kksa dk ikyu djsasaa
Main Power circuit
12 DJ Tripped due to Low OHE or No Tension.
DJ Tripped due to Low OHE or No Tension
Fault OHE Power failure
Follow local instruction
uks Vsa'ku@ yks Vsa'ku
}kjk DJ fVªi
LFkkuh; vuqns”kksa dk ikyu djsasaA
Main power circuit.
13 Loco is earthed. Information
Loco is Earthed
Check BV interlock.Check HOM switch.
Ykksdks vFkZ gS BV b.Vjykd ,oa HOM fLop dh
iksth”ku psd djsasaA
Aux power circuit
14 DJ Tripped Via QOA
DJ Tripped Via QOA
Fault Earth Fault in Auxiliary Circuit
Check all Auxiliary motors & others devices, Isolate faulty auxiliaries. Follow local instruction
If do not succeed Put HQOA at 0. Clear block section & inform TLC.
QOA }kjk DJ fVªi lHkh vkfDtyjh eksVj ,oa lEcfU/kr
midj.kksa dh tkWp djsasa, ,oa nks’kiw.kZ vkfDtyjh dks iFkd ¼vkblksysV½
djsasaA LFkkuh; vuqns”kksa dk ikyu
djsasaA
;fn lQyrk uk feys rkss HQOA dks ^0*
ij djsasa ,oa Cykd lsD”ku iwjk djsasa rFkk
TLC dks lwpuk nsaA
Aux power circuit
15 DJ Tripped Via QVSL – 1
DJ Tripped Via QVSL – 1
Fault Problem in MVSL-1 Blower/ QVSL-1 Relay
Check working of MVSL–1, if MVSL-1 not working put HVSI-1 on 0 and resume traction with half power.
If found working normal, put HVSL-1 on 3. Resume normal Traction
QVSL-1 }kjk DJ fVªi MVSL-1 dh tkWp djsasa ;fn
MVSL-1 dk;Z ugha dj jgk gS rkss
HVSI-1 dks ^0* ij djsasa rFkk gkQ
VSªD”ku pkyw djsasaA
;fn MVSL-1 dk;Z dj jgk gS rkss
HVSL-1 dks 3ij djsa] lkekU;
VSªD”ku pkyw djsasaA
Page 7 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit
16 DJ Tripped Via QVSL – 2
DJ Tripped Via QVSL – 2
Fault Problem in MVSL-2 Blower/ QVSL-2 Relay
Check working of MVSL–2, if MVSL-2 not working put HVSI-2 on 0 and resume traction with half power.
If found working normal, put HVSL-2 on 3. Resume normal Traction
QVSL-2 }kjk DJ fVªi MVSL-2 dh tkWp djsasa ;fn
MVSL-2 dk;Z ugha dj jgk gS rkss
HVSI-2 dks ^0* ij djsasa rFkk gkQ
VSªD”ku pkyw djsasaA
;fn MVSL-2 dk;Z djsa jgk gS rkss
HVSL-2 dks 3ij djsa] lkekU;
VSªD”ku pkyw djsasaA
Aux power circuit
17 DJ Tripped Via QVMT – 1
DJ Tripped Via QVMT – 1
Fault Problem in MVMT-1 /QVMT-1
Check working of MVMT–1 If MVMT-1 is not working then Depending upon load, either work the train up to 5th notch or Isolate Block 1.
If MVMT-1 is working normal, put HVMT-1 on 3. Resume normal Traction.
QVMT-1 }kjk DJ fVªi
MVMT-1 ds dk;Z dh tkWp
djsas] ;fn MVMT-1 dk;Z ugh dj
jgh gS rkss yksM ds vuqlkj 5th ukWp
rd xkM+h dk;Z djsasa ;k Block-1
dks vkblksysV djds xkM+h dk;Z djsasaA
;fn MVMT-1 dk;Z dj jgh gS rkss
HVMT-1 dks 3 ij djsa] lkekU;
VSªD”ku pkyw djsasaA
Aux power circuit
18 DJ Tripped Via QVMT – 2
DJ Tripped Via QVMT – 2
Fault Problem in MVMT-2 /QVMT-2
Check working of MVMT–2 If MVMT-2 is not working then Depending upon load, either work the train up to 5th notch or Isolate Block 2.
If MVMT-2 is working normal, put HVMT-2 on 3. Resume normal Traction.
QVMT-2 }kjk DJ fVªi
MVMT-2 ds dk;Z dh tkWp
djsas] ;fn MVMT-2 dk;Z ugh dj
jgh gS rkss yksM ds vuqlkj 5th ukWp
rd xkM+h dk;Z djsasa ;k Block-2
dks vkblksysV djds xkM+h dk;Z djsasaA
;fn MVMT-2 dk;Z dj jgh gS rkss
HVMT-2 dks 3 ij djsa] lkekU;
VSªD”ku pkyw djsasaA
Page 8 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit
19 DJ Tripped Via QVRH
DJ Tripped Via QVRH
Fault Problem in MVRH/QVRH
Check working of MVRH If MVRH is not working then, work the train up to 5th notch
If MVRH is working normal, put HVRH on 3. Resume normal Traction
QVRH }kjk DJ fVªi MVRH ds dk;Z dh tkWp
djsasa ;fn MVRH dk;Z ugh dj jgk
gS] rkss 5th ukWp rd xkM+h dk;Z
djsasaA
;fn MVRH lgh dk;Z dj jgk gS rkss]
HVRH dks 3 ij djs] lkekU; VªsD'ku
pkyw djsasaA
Aux power circuit
20 DJ Tripped Via QVSI – 1
DJ Tripped Via QVSI – 1
Fault Problem in MVSI-1/QVSI-1
Check working of MVSI-1, , If MVSI-1 is not working, Isolate MVSI-1 by Putting HVSI-1 on 0 Clear block section with half power and consult TLC.
If MVSI-1 is working normal, Put HVSI-1 on 3.Resume normal traction.
QVSI-1 }kjk DJ fVªi MVSI-1 ds dk;Z djus dh tkWp
djsasa] ;fn MVSI-1 dk;Z ugh dj
jgh gS rkss HVSI-1 dks ‘0’ ij
djsasaA gkQ VªSD'ku ikoj ls Cykd
lsD”ku dks iwjk djds TLC dks
lwpuk nsA
;fn MVSI-1 lgh dk;Z dj jgk gS
rkss HVSI-1 dks 3 ij j[k dj]
lkekU; VSD'ku pkyw djsasaA
Aux power circuit
21 DJ Tripped Via QVSI – 2
DJ Tripped Via QVSI – 2
Fault Problem in MVSI-2/QVSI-2
Check working of MVSI-2 , If MVSI-2 is not working, Isolate MVSI-2 by Putting HVSI-2 on 0 Clear block section with half power and consult TLC.
If MVSI-2 is working normal Put HVSI-2 on 3.Resume normal traction.
QVSI-2 }kjk DJ fVªi MVSI-2 ds dk;Z djus dh tkWp
djsasa ;fn MVSI-2 dk;Z ugh dj
jgh gS rkss] HVSI-2 dks ‘0’ ij
djsasaA gkQ VªSD'ku ikoj ls Cykd
lsD”ku dks iwjk djds TLC dks
lwpuk nsA
MVSI-2 lgh dk;Z dj jgk gS] rkss
HVSI-2 dks 3 ij j[kdj lkekU;
VSD'ku pkyw djsasaA
Page 9 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit
22 DJ Tripped Via QPH
DJ Tripped Via QPH
Fault Problem in MPH/QPH
Put HPH on 3.Check oil level of TFP. If does not exceed maximum mark then resume traction. Clear block section and consult TLC.
QPH }kjk DJ fVªi HPH dks 3rd ij djsas TFP vk;y
ysoy dh tkWp djsasa ;fn eSDlhee
ekdZ ls Åij ugha gS] rkss VSªD'ku
pkyw djsasa ,oa Cykd lsD”ku dks iwjk
djds TLC dks lwpuk nsA
Aux power circuit
23 DJ Tripped via QCVAR
DJ Tripped via QCVAR
Fault ARNO problem/QCVAR problem
If Arno is not working Ask for relief Loco
If Arno is working, Check UA voltage. Wedge QCVAR relay using soft Key on display. Resume normal traction.
QCVAR }kjk DJ fVªi vkuksZ ;fn dk;Z ugh dj jgk gS rkss]
lgk;rk batu dh ekWx djsasaA ;fn vkuksZ dk;Z dj jgk gS rkss] UA
dk cksYVst psd djsasaA fMLIyss ij yxh
^lk¶V dh* dh lgk;rk ls QCVAR
dks ost djsasa ,oa lkekU; VªSD'ku pkyw
djsasaA
Aux power circuit
24 DJ Tripped Via QLA
DJ Tripped Via QLA
Fault Over current in Auxiliary circuit
Check auxiliary machines. Isolate faulty auxiliary machine resume normal traction. follow local instruction
If problem still persist, Ask for relief loco
QLA }kjk DJ fVªi lHkh vkfXtyjh e”khuks dks psd djsaas]
nks’k iw.kZ vkfXtyjh e”khu dks i`Fkd
¼vkblksysV½ djsasaA LFkkuh; vuqns”kks
dk ikyu djsasaA
;fn lQyrk u feys rkss] lgk;rk
batu dh ekWx djsasaA
Page 10 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit
25 ICDJ through QOA ICDJ through QOA
Fault Earth fault in Aux. power circuit
Check all Auxiliary motors & others devices, Isolate faulty auxiliaries. follow local instruction
If do not succeed Put HQOA at 0. Clear block section & inform TLC.
QOA }kjk ICDJ lHkh vkfXtyjh eksVjks ,oa vU;
midj.kksa dh tkWp djsasa] nks’k iw.kZ
vkfXtyjh dks i`Fkd ¼vkblksysV½
djsasaA LFkkuh; vuqns”kks dk ikyu
djsaasA
;fn lQyrk ugh feyrh gS rkss]
HQOA dks ‘0’ ij djsasa ,oa Cykd
lsD”ku dks iwjk djsasaA TLC dks lwpuk
nsA
Aux power circuit
26 ICDJ via QLA ICDJ via QLA Fault QLA N/C interlock open
1st Check auxiliary machines
Isolate faulty auxiliary machine resume normal traction. Follow local instruction.
vkfXtyjh e”khu dh tkWp djsasaA
nks’kiw.kZ vkfXtyjh e”khu dks i`Fkd
¼vkblksysV½ djsasaA lkekU; VSD”ku pkyw
djsasaA LFkkuh; vkns”kksa dk ikyu djsasaA
QLA }kjk ICDJ 2nd If problem still persist Ask for relief loco
;fn lQyrk u feys rkss lgk;rk
batu dh ekWx djsasaA
Aux power circuit.
27 Static converter Internal fault
Static converter Internal fault
Fault Internal fault in SIV
Check SIV display screen for fault lamp and follow instruction. If do not succeed press reset button.
If the problem persists Put HBA OFF for 10 sec and try again
LVSfVd dUoVZj]
b.Vjuy QkYV LVsfVd duoZVj ds fMLIyss ij QkYV
ySEiks dh tkWp djsas ,oa lEcfU/kr
vuqns”kksa dk ikyu djsasaA ;fn
lQyrk ugha feyrh gS rkss fjlsV Ikq”k
cVu dks nck;saA
;fn lQyrk ugh feyrh gS rkss HBA
fLop dks 10 lsds.M ds fy;s OFF djsas ,oa iqu% dksf”k”k djsasaA
Page 11 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit.
28 Static converter External Fault
Static converter External Fault
Fault External fault in SIV
Check SIV display screen for fault lamp and follow instruction. If do not succeed press reset button.
If the problem persists Put HBA OFF for 10 sec and try again
LVSfVd
dUoVZj] ,DlVuZy
QkYV
LVsfVd duoZVj ds fMLIyss ij QkYV
ySEiks dh tkWp djsas ,oa lEcfU/kr
vuqns”kksa dk ikyu djsasaA ;fn
lQyrk ugha feyrh gS rkss fjlsV Ikq”k
cVu dks nck;saA
;fn lQyrk ugh feyrh gS rkss HBA
fLop dks 10 lsds.M ds fy;s OFF djsas ,oa iqu% dksf”k”k djsasaA
Aux power circuit.
29 SIV not picking up SIV not picking up
Fault Fault in SIV Check SIV display screen for fault lamp and follow instruction. If do not succeed press reset button.
If the problem persists Put HBA OFF for 10 sec and try again
SIV dk pkyw u gksuk LVsfVd duoZVj ds fMLIyss ij QkYV
ySEiks dh tkWp djsas ,oa lEcfU/kr
vuqns”kksa dk ikyu djsasaA ;fn
lQyrk ugh feyrh gS rkss fjlsV Ikq”k
cVu dks nck;saA
;fn lQyrk ugh feyrh gS rkss HBA
fLop dks 10 lsds.M ds fy;s OFF djsas ,oa iqu% dksf”k”k djsasaA
Aux power circuit.
30 MVMT’s and MVRH not working
MVMT’s and MVRH not working due to QCON feedback fail
Fault Fault in SIV Ensure all other auxiliaries working. Press soft key on display to bypass QCON. Resume normal traction
MVMT’s & MVRH dk dke u djuk
lHkh vkfXtyjh dk dk;Z djuk
lqfuf”pr djsasaA fMLIyss ij yxh
lk¶V dh (Soft Key) ls QCON
dks okbZikl djsasa] lkekU; V SD”ku
pkyw djsasaA
Page 12 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit.
31 HVMT- 1 in Position 0Block 1 isolated.
Half power available.
HVMT 1 in Position 0 L1 L2 L3 Cut Off Half Power available
Isolation - -
HVMT-1 iksth”ku
^0*A Cykd 1 vkblksysVA vk/kh “kfDr miyC/kA
Aux power circuit.
32 HVMT- 2 in Position 0 Block 2 isolated Half Power available
HVMT 2 in Position 0 L4 L5 L6 Cut Off Half Power available
Isolation
HVMT2 iksth”ku ^0*A
Cykd 2 vkblksysVA vk/kh “kfDr miyC/kA
Traction Control circuit
33 DJ Tripped due to GR Stuck ON notches
DJ Tripped due to GR Stuck ON notches
Fault DJ Tripping due to GR Stuck ON / FULL notch (Q46 Tripping)
1st Check LSGR is not glowing. bring GR to 0 manually
Reclose DJ to resume traction.
LSGR ySEi dks psd djsasaA ;fn ugha
ty jgk gS rkss GR dks eSuqvyh ^0*
djsasaA
iqu% DJ dk cUn djsasa] VSªD”ku pkyw
djsasaA
GR dks ukWp ij Qlus
ls DJ fVªi
2nd
If the problem persists put ZSMGR on 0.Clear block section by operating GR manually.
--
;fn lQyrk ugha feyrh gS rkss] ZSMGR dks ^0* ij djsasa rFkk Cykd
lsD”ku dks Dyh;j djsasaA
&&
Page 13 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction Control Circuit
34 DJ Tripped due to GR Stuck between notches
DJ Tripped due to GR Stuck between notches
Fault
Half notch tripping
1st Check LSGR is not glowing. bring GR to 0 manually
Reclose DJ to resume traction.
LSGR ySEi dks psd djsasaA ;fn ugha
ty jgk gS rkss GR dks eSuqvyh ^0*
Dyh;j djsasaA
iqu% DJ dk cUn djsasa] VSªD”ku pkyw
djsasaA
GR dks ukWpks ds e/;
Qlus ls DJ fVªi
2nd If the problem persists put ZSMGR on 0.Clear block section by operating GR manually.
;fn lQyrk ugha feyrh gS rkss] ZSMGR dks ^0* ij djsasa rFkk Cykd
lsD”ku dks eSuqvyh iwjk djsasaA
Traction control circuit
35 Total Loss of Traction (TLTE) due to reverser not set as per MPJ position.
Total Loss of Traction(TLTE) due to reverser not set as per MPJ position
Fault Check LSB status. If LSB is glowing set reverser manually.
If LSB is still glowing wedge Q50 by using soft key on display panel after taking necessary precautions.Clear block section and inform TLC.Do not use DBR
dqy d"kZ.k gkfu;kW
(TLTE) fjolZj dk
MPJ dh iksth”ku ds
vuqlkj lsV u gksuk
LSB ik;yV ySEi dh tkWp
djsasa ;fn ty jgk gS rkss fjolZj dks
eSuqvyh lsV djsasaA
;fn LSB fQj Hkh ty jgh gS rkss
vko”;d lko/kkfu;kWa ysrs gq, Q-50
dks fMLIyss ij yxh ^lk¶V dh* ls ost
djsasaA Cykd lsD”ku dks iwjk djsasa ,oa
TLC dks lwpuk nsaA DBR dk iz;ksx
u djsasaA
Page 14 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction control circuit
36 Total loss of traction (TLTE) due to CTF’s not set as per MP position.
Total loss of traction due to CTF’s not set as per MP position.
Fault Check LSB status. If LSB is glowing set CTF’s manually.
If LSB is still glowing wedge Q50 by using soft key on display panel after taking necessary precautions.Clear block section and inform TLC. Do not use DBR.
dqy d"kZ.k gkfu;kW
(TLTE) MP iksth”ku
ds vuqlkj CTF’s ds u
lsV gksukA
LSB ik;yV ySEi dh tkWp
djsasa ;fn ty jgk gS rkss CTF dks
eSuqvyh lsV djsasaA
;fn LSB fQj Hkh ty jgh gS rkss
vko”;d lko/kkfu;kWa ysrs gq, fMLIyss
ij yxh ^lk¶V dh* ls Q-50 dks ost
djsasaA Cykd lsD”ku dks iwjk djsasa ,oa
TLC dks lwpuk nsaA DBR dk iz;ksx
u djsasaA Traction control circuit
37 Line contactor L-1 stuck up
Line contactor L1 stuck up
Fault Do not use DBR. Resume normal traction.
ykbu dkUVsDVj L-1 dk Q¡l tkuk
DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
38 Line contactor L-2 stuck up
Line contactor L2 stuck up
Fault Do not use DBR. Resume normal traction.
ykbu dkUVsDVj L-2 dk Q¡l tkuk
DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
39 Line contactor L-3 stuck up
Line contactor L3 stuck up
Fault Do not use DBR. Resume normal traction.
ykbu dkUVsDVj L-3 dk Q¡l tkuk
DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djs asaA
Traction control circuit
40 Line contactor L-4 stuck up
Line contactor L4 stuck up
Fault Do not use DBR. Resume normal traction.
ykbu dkUVsDVj L-4 dk Q¡l tkuk
DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
41 Line contactor L5 stuck up
Line contactor L5 stuck up
Fault Do not use DBR. Resume normal traction.
ykbu dkUVsDVj L-5 dk Q¡l tkuk
DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Page 15 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction control circuit
42 Line contactor L-6 stuck up
Line contactor L6 stuck up
Fault Do not use DBR. Resume normal traction.
ykbu dkUVsDVj L-6 dk Q¡l tkuk
DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
43 DBR not working. C145 open in DB mode due to both HMCS1 & 2 not in 1
Information
Both HMCS1 & 2 not on position 1
Do not use DBR. Resume normal traction.
DBR dk dke u djuk DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
44 DBR not working. C145 open in DB mode due to DBR overheated or QE acted.
Information
Do not use DBR. Resume normal traction.
DBR dk dke u djuk DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
45 DBR not working. QVRF not picking up. Do not use DB.
Information
Fault with MVRF/QVRF
Do not use DBR. Resume normal traction.
DBR dk dke u djuk DBR dk iz;ksx u djsasaA lkekU;
VSªD”ku pkyw djsasaA
Traction control circuit
46 Total Loss Of Tractive Effort(TLTE) via RGEB
Total Loss Of Tractive Effort(TLTE) via RGEB
Fault Maintain 5Kg/sq cm BP pressure and resume normal traction.
If do not succeed,ensure BP pressure5Kg/sqcm and release of train brakes, put HPAR on 1 and resume normal traction.
RGEB }kjk dqy d"kZ.k
gkfu;kW (TLTE)
ch0ih0 izs”kj 5kg/cm2 esUVsu
djsasa ,oa lkekU; VSD”ku pkyw djsasaA
;fn lQyrk ugha feyrh gS rkss ch0ih0
izs”kj dk 5kg/cm2 gksuk lqfuf”pr
djsasa rFkk Vsªu czsd fjyht djsasaA HPAR dks ‘1’ ij djsasa o lkekU; VSD”ku pkyw
djsasaa
Page 16 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction control circuit
47 C145 stuck up / welded.
C145 stuck up / welded.
fault Fault with C145 relay/its auxiliary contact
Make loco dead by putting HBA off.Open C145 manually.Re energise loco to resume traction.
Do not use DBR.
C-145 dk QWluk
@osYM gksuk ‘HBA’ fLop dks OFF djsasa] yksdks
dks MsM djsasa rFkk C-145 dks
eSuqvyh vksisu djsasaA yksdks dks iqu%
bujtkbt djsasa ,oa VSD”ku pkyw djsasaA
DBR dk iz;ksx u djsasaA
Traction control circuit.
48 Brake applied through IP
Brake applied through IP
Fault Put MPon 0.If IP remains de-energised, isolate IP cock & do not use DBR.
IP okYo }kjk czsd yxuk ‘MP’ dks ‘0’ ij djsasa ;fn IP Valve fQj Hkh Mhbujtkbt gS rkss
IP dkWd dks vkblksysV djsasaaA DBR dk iz;ksx uk djsasaA
Traction control circuit
49 Auto-regression via ACP
Auto-regression via ACP
Fault Attend ACP.Press BPSW.Resume normal traction
If do not succeed,ensure BP pressure at 5Kg/sqcm and release of train brakes, put HPAR on 1 and resume normal traction.
vkWVksfjxzs”ku ACP ds}kjk ACP dks Bhd djsasa] BPSW fLop dks nck;sa] lkekU; VSªD”ku pkyw djsasaA
;fn lQyrk ugha feyrh gS rkss BP izs”kj dk 5kg/cm2 gksuk ,oa Vsªu czsd
fjyht gksuk lqfuf”pr djsasaaA HPAR dk ‘1’ ij djsasa vkSj lkekU; VSªD”ku
pkyw djsasaaA
Traction control circuit
50 DBR not working. Auto regression via QF1 operated
Information
Do not use DBR.
DBR dk dke u djuk DBR dk iz;ksx u djsasaA
Traction control circuit
51 DBR not working. Auto regression via QF2 operated
Information
Do not use DBR.
DBR dk dke u djuk DBR dk iz;ksx u djsasaA
Page 17 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction control circuit
52 Auto-regression via RGEB
Auto-regression via RGEB
Information
Maintain 5Kg/sq cm BP pressure and resume normal traction.
If do not succeed,ensure BP pressure at 5Kg/sqcm and release of train brakes, put HPAR on 1 and resume normal traction.
vkWVksfjxzs”ku RGEB ds}kjk
BP izs”kj 5kg/cm2 gksuk
lqfuf”pr djsasa ,oa lkekU; VSªD”ku
pkyw djsasaA
;fn lQyrk ugha feyrh gS rkss BP izs”kj 5kg/cm2 ,oa Vsªu dk fjyht
gksuk lqfuf”pr djsasaA HPAR dks ^1*
ij djsasa vkSj lkekU; VSªD”ku pkyw djsasaaA
Traction control circuit
53 Auto-regression via QD1
Auto-regression via QD1.
Fault Press BPQD to negotiate gradient.Clear Block section.If the problem persists then Isolate faulty TM and resume normal traction
vkWVksfjxzs”ku QD-1 ds }kjk
BPQD fLop dks nckdj xzsfM;sV
lSD”ku dks iwjk djsasaA ;fn lQyrk
ugh feys rkss nks’kiw.kZ VSªD”ku eksVj
dks vkblksysV djsasA
Traction control circuit.
54 Auto-regression via TM Over Voltage
Auto-regression via TM Over Voltage
Information
vkWVksfjxzs”ku TM vksoj
oksYVst }kjk Traction control circuit.
55 Auto-regression via QD2.
Auto-regression via QD2.
Fault Press BPQD to negotiate gradient.Clear Block section.If the problem persists then Isolate faulty TM and resume normal traction
vkWVksfjxzs”ku QD-2 ds }kjk
BPQD fLop dks nckdj xzsfM;sV
lSD”ku dks iwjk djsasaA ;fn lQyrk
ugh feys rkss nks’kiw.kZ VSªD”ku eksVj
dks vkblksysV dj rFkk lkekU;
VSªD”ku pkyw djsasaA
Page 18 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction control circuit.
56 Auto regression via C145 Contactor
Auto regression via C145 Contactor
Fault Make loco dead by putting HBA off.Open C145 manually.Re energise loco to resume traction.
Do not use DBR
vkWVksfjxzs”ku C145 ds }kjk
HBA fLop dks vkQ djsasa] yksdks dks
MsM djsa] C-145 dks eSuqvyh [kksysaA
yksdks dks iqUk% bujtkbt djsasa]
VSªD”ku pkyw djsasaA
DBR dk iz;ksx u djsasaA
Traction control circuit.
57 Auto regression via Q51 of other loco
Auto regression via Q51 of other loco
Fault Put HPAR on 1 of both the locomotives and resume normal traction.
vkWVksfjxzs”ku nqljs yksdks
ds Q-51 ds }kjk nksuksa yksdks ds HPAR fLop dks ^1*
ij djsasa ,oa lkekU; VSªD”ku pkyw
djsasaA
Traction control circuit.
58 DBR not working. Braking fault SWC operated.
Fault Do not use DBR
DBR dk dke u djuk DBR dk mi;ksx u djsasaA
Traction control circuit.
59 Q51 Bypassed
HPAR is on 1 Isolation
Q-51 ckbZikl
Traction control circuit.
60 Q51 restored
HPAR is on 0 Information
Q-51 jhLVksj
Page 19 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Auxiliary Control circuit
61 DJ tripped via C-107Contactor
DJ tripped via C107
Fault Problem in Aux. contacts of C-107 or C-107 contactor itself defective
Ensure working of MVRH by reclosing DJ.If MVRH is working,wedge Q118 by Pressing Q118 soft key on display panel before 5
th notch.
Resume normal traction
If MVRH is not working, wedge/close C-107 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel.Resume normal traction
C-107 dkUVsDVj }kjk
DJ fVªi gksuk
DJ dks iqu% cUn djsasaA MVRH dk;Z
djuk lqfuf”pr djsasa] ;fn MVRH dk;Z dj jgk gks rkss fMLIyss iSuy ij
yxh Q-118 ^lk¶V dh* dks
nckdj 5 ukWp ls igys ost djsasa ,oa
lkekU; VSªD”ku pkyw djsasaA
;fn MVRH dk;Z ugha dj jgk gS rkss
vko”;d lko/kkfu;kW ysrs gq, C-107
dks ost djsasasa] Q-118 dks ^lk¶V dh*
ls ost djsasa blds i”pkr iqu% DJ cUn djsasa ,oa lkekU; VSªD”ku pkyw djsasaaA
Auxiliary Control circuit
62 DJ tripped via C-106 Contactor
DJ tripped via C106 Contactor
Fault Problem in Aux. contacts of C106 or C106 contactor itself defective
Ensure working of MVMT-2 by reclosing DJ.In case MVMT-2 is working wedge Q118 by pressing Q118 soft key on display panel before 5
th notch.
Resume normal traction
If MVMT-2 is not working, wedge/close C-106 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-106 dkUVsDVj }kjk
DJ fVªi gksuk
DJ dks iqu% cUn djsasaA MVMT-2, dk dk;Z djuk lqfuf”pr djsa fMLIyss
ij yxs Q-118 ^lk¶V dh* dh
lgk;rk ls 5 ukWp ls igys ost
djsasaA lkekU; VSªD”ku pkyw djsasaA
;fn MVMT-2 dk;Z ugha djsa jgh gS
rkss vko”;d lko/kkfu;kW ysrs gq, C-106 dks ost djsaA DJ cUn djsasa]
fMLIyss iSuy ij yxs Q-118 ^lk¶V
dh* dh lgk;rk ls ost djsasaaA lkekU;
VSªD”ku pkyw djsasaA
Page 20 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Auxiliary Control circuit
63 DJ tripped via C-105 Contactor
DJ tripped via C105 Contactor
Fault Problem in Aux. contacts of C105 or C105 contactor itself defective
Ensure working of MVMT-1 by reclosing DJ. In case MVMT-1 is working wedge Q118 by pressing Q118 soft key on display panel before 5
th notch.
Resume normal traction
If MVMT-1 is not working, wedge/close C-105 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
dkUVsDVj C-105 }kjk
DJ fVªi gksuk
DJ Close djsasa rFkk MVMT-1 ds
dk;Z dh tkWp djsasaA ;fn MVMT-1
dk;Z dj jgh gS rkss fMLIyss iSuy ij
yxh ‘Soft Key Q-118’ dks
nckdj Q-118 dks ost djsasaA
lkekU; VSªD”ku pkyw djsasaA
;fn MVMT-1 dk;Z ugha dj jgh gS
rkss vko”;d lko/kkfu;kWa ysrs gq, C-105 dks ost djsasaA Q-118 dks ‘Soft Key’ ls ost djsasa rFkk DJ Dykst
djds] VSªD”ku pkyw djsaasA
Auxiliary Control circuit
64 DJ Tripped Via C-118 N/C Interlock Fail
DJ Tripped Via C118 N/C Interlock Fail
Fault Problem in auxiliary contact of C118.
Ensure opening of C-118 contactor. Wedge Q118 by pressing Q118 soft key on display panel and reclose DJ. Clear block section & inform TLC
C-118 N/C bUVjykd
Qsy gksus ij
DJ fVªi gksuk
C-118 dkUVSDVj dk [kqyk gksuk
lqfuf”pr djsasaaA fMLIyss iSuy ij
yxh ‘Soft Key Q-118’ dks
nckdj Q-118 dks ost djsasaA
DJ Dykst djsasa] Cykd lSD”ku iwjk
djsaasA TLC dks lwpuk nsaA
Page 21 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux control circuit
65 ICDJ via C-118 N/C contact failure
ICDJ via C118 N/C contact defective
Fault Put HBA on zero. Ensure opening of C-118 contactor. Wedge Q118 by using soft key on the display after taking necessary precautions. Reclose DJ and Resume normal traction & inform TLC.
C-118 N/C dkUVsDV
Qsy gkus ij ICDJ gksuk
HBA fLop dks vkQ djsasa] C-118
dkUVSDVj dk [kqyk gksuk lqfuf”pr
djsaasA vko”;d lko/kkfu;kWa ysrs gq,
fMLIyss iSuy ij yxh ‘Soft Key Q-118’ dks nckdj Q-118
dks ost djsasaA iqu% DJ Dykst djsasa]
VSªD”ku pkyw djsasaA TLC dks lwpuk
nsaA
Aux control circuit.
66 Unloader continuously working and MR pressure not maintaining.
Unloader continuously working and MR pressure not maintaining. Feed from C101, 102& 103 fail.
Fault Unloader continuously working & MR pressure not maintaining. Isolate VEUL by VEUL isolating COCK.
vuyksMj okYo ds
yxkrkj dke djus ls
MR izs”kj esUVsu ugha gks
jgk
VEUL rFkk MR dk izs”kj esUVsu
ugha gks jgk gS] vuyksMj okYo
yxkrkj dk;Z dj jgk gSA VEUL
vkblksysfVax dkd dh lgk;rk ls VEUL dks vkblksysV djsasaA
Page 22 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux control circuit
67 ICDJ through C-107 N/O interlock
ICDJ through C107 N/O interlock
Fault C107 N/C interlock open
Check for permanent welding or wedging of C-107 contactor. If welded or wedged, wedge Q118 by soft key on display, re-close DJ and resume normal traction.
If not welded or wedged then wedge/close C-107 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-107 N/O b.Vj
ykd }kjk ICDJ
C-107 dh dkUVSDVj dh tk¡p djsasA
osYM@ost gS rkss fMLIyss iSuy ij
yxh ‘Soft Key Q-118’ dks
nckdj Q-118 dks ost djsasaA
iqu: Mh-ts cUn djsasa] lkekU; VªSD”ku
pkyw djsasA
;fn C-107 osYM@ost ugh gS rkss
vko”;d lko/kkfu;k¡ ysrs gq, eSU;wyh
ost djsasaA fMLIyss iSuy ij yxh ‘Soft Key Q-118’ dks nckdj Q-118
dks ost djsasaA DJ cUn djsasa] lkekU;
VªSD”ku pkyw djsaasA
Aux control circuit
68 ICDJ through C-106 N/O interlock
ICDJ through C106 N/O interlock
Fault C106 N/C interlock open
Check for permanent welding or wedging of C-106 contactor. If welded or wedged, wedge Q118 by soft key on display, Reclose DJ and resume normal traction.
If not welded or wedged then wedge/close C-106 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-106 N/O b.Vj
ykd }kjk ICDJ
C-106 dh dkUVSDVj dh tk¡p djsasA
osYM@ost gS rkss fMLIyss iSuy ij
yxh ‘Soft Key Q-118’ dks
nckdj Q-118 dks ost djsasaA
iqu: Mh-ts cUn djsasA lkekU; VªSD”ku
pkyw djsasA
;fn C-106 osYM@ost ugh gS rkss]
vko”;d lko/kkfu;k¡ ysrs gq, eSU;wyh
ost djsasA fMLIyss iSuy ij yxh ‘Soft Key Q-118’ dks nckdj Q-118
dks ost djsasaA iqu: DJ cUn djsasA
lkekU; VªSD”ku pkyw djsasA
Page 23 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux control circuit
69 ICDJ through C-105 N/O interlock
ICDJ through C105 N/O interlock
Fault C105 N/C interlock open
Check for permanent welding or wedging of C-105 contactor. If welded or wedged, wedge Q118 by soft key on display, Reclose DJ and resume normal traction.
If not welded or wedged then wedge/close C105 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-105 N/O b.Vj
ykd }kjk ICDJ
C-105 dkUVSDVj dks tk¡p djsasA
osYM@ost gS rkss fMLIyss iSuy ij
yxh ‘Soft Key Q-118’ dks
nckdj Q-118 dks ost djsasaA
iqu: Mh-ts cUn djsasA lkekU; VªSD”ku
pkyw djsasA
;fn C-105 osYM@ost ugh gS rkss]
vko”;d lko/kkfu;k¡ ysrs gq, eSU;wyh
ost djsasA fMLIyss iSuy ij yxh ‘Soft Key Q-118’ dks nckdj Q-118
dks ost djsasaA iqu: DJ cUn djsasA
lkekU; VªSD”ku pkyw djsasA
DJ closing and panto circuit
70
DJ Tripped Via QPDJ
DJ Tripped Via QPDJ
Fault
RS pressure low/Defect in QPDJ
1st Put ZPT on zero. Check RS Pressure. I fit is less than 8 Kg/sq cm, start auxiliary compressor to build up pressure above 8Kg/Sqcm. Try to close DJ and resume normal traction
Put ZPT on zero .Check if RS pressure is above 8 Kg/Sq cm, drain RS reservoir and rebuild pressure above 8Kg/Sqcm with CPA.Close DJ and resume normal traction.
QPDJ }kjk DJ fVªi
ZPT dks ^0* ij djsa] RS izs”kj dh
tkWp djsa ;fn 8 kg/ cm2 ls de
gS rks vkfDtyjh dEizs”kj pyk dj
8 kg/cm2 izs”kj cuk;saA DJ cUn
djsasA lkekU; VªSD”ku pkyw djsasA
ZPT dks ^0* ij djsa] RS izs”kj dh
tkWp djsa ;fn 8 kg/ cm2 ls T;knk
gS rks RS fjtokZ;j dk izs”kj
fudkysa ,oa iqu% 8 kg/cm2 izs”kj
cuk;saA DJ cUn djsasA lkekU; VªSD”ku
pkyw djsasA
Page 24 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
DJ closing and panto circuit
70 DJ Tripped Via QPDJ
2nd
If RS pressure is not maintaining, check working of baby compressor and its safety valve, leakages from VEPT-1 &2, R1, and RAL cock.Try to arrest leakages. Startauxiliary compressor to build up pressure above 8Kg/Sqcm. Reclose DJ and resume normal traction. Warning: After MR pressure is 10Kg/Sq cm do not forget to open R1 cock.
QPDJ }kjk DJ fVªi ;fn RS dk izs”kj esUVsu ugha gks jgk
gS rks csch dEizs”kj vkSj ls¶Vh okYo
ds dk;Z dh tkWp djsa VEPT-1
&2 , R-1, ,oa RAL dkd dh
yhdst dh tkWp djsaA ;fn dksbZ
yhdst gks rks mls cUn djsaA
vkfDtyjh dEizs”kj dks pyk dj 8
kg/cm2 izs”kj cuk;sa iqu% DJ cUn
djsaA lkekU; VSªD”ku pkyw djsaA
lko/ku &MR dk izs”kj 10
kg/cm2 gks tkus ij R-1 dkd dk
[kksyuk u HkwysaaA
Page 25 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
DJ closing and panto circuit
71 DJ tripped due to VCB defective
DJ tripped due to VCB defective
Fault Internal defect in VCB unit
Coast to clear Block Section. Put HBA on 0 and switch it ON after 5 seconds. Drain RS reservoir and rebuild pressure above 8Kg/Sqcm with CPA. Close DJ and resume normal traction. If don’t succeed ask for relief loco.
VCB [kjkc gksus ds
dkj.k DJ fVªi
dksfLVax djrs gq;s Cykd lsD”ku iwjk
djsasA HBA dks ^0* ij djsasa rFkk 5
lsds.M ds ckn vkWu ij djsasaA RS izs”kj dks Mªsu djsasaA CPA }kjk iqu: 8kg/cm2 izs”kj cuk;saA DJ cUn djsasa] lkekU; VªSD”ku pkyw djsasA ;fn
lQyrk ugh feyrh g]S rkss fjfyQ
batu dh ek¡x djsasA
DJ closing and panto circuit
72 DJ tripped Via QSIT
DJ tripped Via QSIT
Fault Safety relay for SIV operated
Check SIV display screen for fault lamp and follow instruction. If do not succeed press reset button.
If the problem persists PUT HBA OFF for 10 sec and try again
QSIT }kjk DJ fVªi SIV fMLIyss Ldzhu esa QkYV ySEi dh
tk¡p djsasa rFkk vuqns”kks dk ikyu
djsasA ;fn lQyrk ugh feyrh gS
rkss] fjlsV cVu dks nck;sA
;fn lQyrk ugh feyrh gS rkss] HBA
dks 10 lSds.M ds fy;s vkQ djsaasA iqu: dksf”k”k djsasaA
DJ closing and pinto circuit
73 DJ Tripped via BPEMS
DJ Tripped via BPEMS
Fault Emergency push button switch operated
Put ZPT at zero. Reset BPEMS by rotating switch in appropriate direction. Resume normal traction
If do not succeed change cab and resume normal traction.
BPMS }kjk DJ fVªi ZPT dks ‘0’ ij djsasA BPEMS dks
lgh fn”kk es /kqekdj fjlsV djsasA
lkekU; VªSD”ku pkyw djsasA
;fn lQyrk ugh feyrh gS rkss dSo
dks cnys] vkSj lkekU; VªSD”ku pkyw
djsasA
Page 26 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Panto and DJ circuit
74 ICDJ via QPDJ
ICDJ via QPDJ
Fault QPDJ N/O interlock open
Put ZPT on zero. Check RSPressure. If it is less than 8 Kg/sq cm, start auxiliary compressor to build up pressure above 8Kg/Sqcm. Try to close DJ and resume normal traction If RS pressure is not maintaining, check working of baby compressor and its safety valve, leakages from VEPT1 &2, R1, RALcock. Try to arrest leakages. Start auxiliary compressor to build up pressure above 8Kg/Sqcm. Reclose DJ and resume normal traction. Warning: After MR pressure is 10Kg/Sq cm do not forget to open R1 cock
Put ZPT on zero .Check if RS pressure is above 8 Kg/Sq cm, drain RS reservoir and rebuild pressure above 8Kg/Sqcm with CPA. Close DJ and resume normal traction.
Page 27 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Panto and DJ circuit
74 QPDJ }kjk ICDJ ZPT dks ‘0’ ij djsasA RS dk
izs”kj psd djsas ;fn
8kg/cm2ls de gS rkss csch
dEizs”kj dks pkyw djsas ,oa
8kg/cm2 dk izs”kj cuk;sA DJ cUn djsaus dk iz;kl djsasA
lkekU; VªSD”ku pkyw djsasA ;fn
RS izs”kj esUVsu ugh gks jgk gS rkss csch dEizs”kj ls¶Vh okYo
SS-2] VEPT-1, VEPT-2
ls yhdst dh tk¡p djsasA
R1 ,oa RAL Cock dks tk¡p
djsasA ;fn yhdst gS rkss mls
cUn djsasA csch dEizs”kj dks iqu: LVkVZ djsas rFkk 8kg/cm2ls
vf/kd izs”kj cuk;sA iqu: DJ cUn djsasA lkekU; VªSD”ku pkyw
djsaasA
psrksouh&MR izs”kj
10kg/cm2 gksus ds i”pkr
R-1 Cock dks [kksyuk uk
HkwysaA
ZPT dks O ij djsasA RS dk
izs”kj psd djsas ;fn 8kg/cm2 ls vf/kd izs”kj gS rkss RS dk
izs”kj Mªsu djsaA iqu: 8kg/cm2 ls vf/kd izs”kj] csch dEizs”kj dh
lgk;rks ls cuk;sA DJ cUn djsas
lkekU; VªSD”ku pkyw djsasA
Page 28 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Panto and DJ circuit
75 ICDJ through QSIT Dropped
ICDJ through QSIT Dropped
Fault Safety relay for SIV operated
Check SIV display screen for fault lamp and follow instruction. If do not succeed press reset button.
If the problem persists PUT HBA OFF for 10 sec and try again
QSIT }kjk ICDJ SIV fMLIyss Ldzhu esa QkYV ySEiksa
dks ns[ksa rFkk funsZ”kkas dk ikyu
djsasaA ;fn lQyrk ugha feyrh gS rkss
‘RESET’ cVu dks nck;saA
;fn izksCye cuh jgrh gS rkss HBA dks
10ls- rd vkQ djsasa rFkk iqu: dksf”k”k
djsasaA
Panto and DJ circuit
76 ICDJ through BPEMS ICDJ through BPEMS
Fault Emergency push button switch operated
Put ZPT at zero. Reset BPEMS by rotating switch in appropriate direction. Resume normal traction
If do not succeed change cab and resume normal traction.
BPEMS gksus ds dkj.k
ICDJ ZPT dks ‘0’ ij djsasA BPEMS dh
ukc dks mfpr fn”kk es ?kqekdj
fjlsV djsasA lkekU; VªSD”ku pkyw
djsasA
;fn lQyrk ugh feyrh gS rkss dSc
cnyh djsasa ,oa lkekU; VªSD”ku pkyw
djsasA
Page 29 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Panto and DJ circuit
77 ICDJ via VCB defective
ICDJ via VCB defective
Fault Internal defect in VCB unit
Coast to clear Block Section. Put HBA on 0 and switch it ON after 5 seconds. Drain RS reservoir and rebuild pressure above 8Kg/Sqcm with CPA. Close DJ and resume normal traction. If don’t succeed ask for relief loco.
VCB [kjkc gksaus ds
dkj.k ICDJ
dksfLVxa esa Cykd lsD”ku iwjk djsasA
HBA dks ^0* ij djsaas rFkk 5 lsds.M
ckn vku djsasA RS fjtjok;j dks
Mªsu djsas csch dEizs”kj }kjk
8kg/cm2 dk izs”kj cuk dj]
Dykst djsasa rFkk lkekU; VªSD”ku pkyw
djsasA ;fn lQyrk u feys rkss
fjyhQ batu dh ekax djsasA
Panto and DJ circuit
78 BPEMS switch is in pressed Condition.
BPEMS switch is in pressed Condition.
Information
Put ZPT at zero. Reset BPEMS by rotating switch in appropriate direction. Resume normal traction
If do not succeed change cab and resume normal traction.
BPEMS fLop izsl
fLFkfr esa gS ZPT dks ‘0’ ij djsasA BPEMS dks
lgh fn”kk es /kqekdj fjlsV djsasA
lkekU; VªSD”ku pkyw djsasA
;fn lQyrk ugh feyrh gS Rkks dSc
cnyh djsasa ,oa lkekU; VªSD”ku pkyw
djsasA
Page 30 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Battery power circuit
79 Battery Charger Output Failed
Battery Charger Output Failed
Information
Switch off unwanted lights in the cab for reducing the consumption of battery .Check battery voltage. If battery voltage is greater than 90V keep the loco operational and clear block section.Inform TLC.
cSVjh pktZj vkmViqV
Qsy cSVjh dks cpkus ds fy;s vuko”;d
ykbV dks cUn djsasaA CkSVjh oksYVst
psd djsas ;fn 90V ls T;knk gS rkss
yksdks pkyw j[ksa rFkk Cykd lsD”ku
Dyh;j djsasA TLC dks lwfpr djsasaA
Battery power circuit
80 Battery Voltage Low Battery Voltage Low
Information
Switch off unwanted lights in the cab for reducing the consumption of battery .Check battery voltage.If battery voltage is greater than 90V keep the loco operational and clear block section.Inform TLC.
cSVjh oksYVst de gSA cSVjh dks cpkus ds fy;s vuko”;d
ykbV dks cUn djsasA CkSVjh oksYVst
psd djsasA ;fn 90V ls T;knk gS rkss
yksdks pkyw j[ks rFkk Cykd lsD”ku
Dyh;j djsasaA TLC dks lwfpr djsasaA
Battery power circuit
81 CCPT fuse melted CCPT fuse melted
Fault
Replace CCPT fuse. Resume normal traction.
If melts again put HOBA on off & replace fuse and resume normal traction.
CCPT ¶;wt esYV gks
x;k gS CCPT ¶;wt dks cnysaA lkekU;
VªSD”ku pkyw djsasA
;fn iqu: esYV tk;s rkss HOBA dks
vkQ djds ¶;wt dks cnys rFkk
lkekU; VªSD”ku pkyw djsasaA
Page 31 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Battery power circuit
82 CCDJ fuse melted CCDJ fuse melts
Fault Replace CCDJ fuse. Resume normal traction.
If melts again put HOBA on off & replace fuse and resume normal traction.
CCDJ ¶;wt esYV gks
x;k gS CCDJ ¶;wt dks cnysaA lkekU;
VªSD”ku pkyw djsasA
;fn iqu: esYV tk;s rkss HOBA dks
vkQ djsaas] ¶;wt dks cnys rFkk lkekU;
VªSD”ku pkyw djsasaA
Battery power circuit
83 CCA fuse melted CCA fuse melted Fault Replace CCA fuse. Resume normal traction.
If melts again put HOBA on off & replace fuse and resume normal traction.
CCA ¶;wt esYV gks
x;k gS CCA ¶;wt dks cnysaA lkekU;
VªSD”ku pkyw djsasA
;fn iqu: esYV tk;s rkss HOBA dks
vkQ djsasA lkekU; VªSD”ku pkyw djsasaA
VCD and speedometer
84 VCD active
VCD active Information
VCD dk;Zjr
85 VCD bypass VCD bypass Information
VCD ckbikl
VCD& Speedometer
86
Vigilance Penalty Brake Applied
Penalty Brake Applied
Fault Put MP at 0.After 32 seconds press Vigilance Reset push button to release Penalty brakes. Resume normal traction.
If do not succeed then isolate IP valve with isolating cock.
foftysal isukYVh czsd
yx x;k gS MP dks ^0* djsasA 32 ls- ds ckn
foftysal fjlsV cVu dks nckdj]
isukYVh czsd dks fjyht djsasA lkekU;
VªSD”ku pkyw djsasA
;fn lQyrk ugh feyrh gS rkss IP Valve dks vkblksysfVx dkd dh
enn ls vkblksysV djsasaA
Page 32 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
87 DJ tripped due to internal fault in MPCS
Digital output card 1 failed
Fault Output card 1 has become faulty. System switches over to the RDT output card. The exact nature of the fault shall be mentioned in the diagnostic message.
1st Wait for 5 seconds and re close
DJ. Resume normal traction. If do not succeed reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , reclose DJ. In case the fault persists call for Relief loco.
5 lsds.M rd bartkj djsasA mlds
ckn iqu:DJ cUn djsaasA lkekU;
VªSD”ku pkyw djsasaA
;fn lQyrk ugh feyrh gS rkss
MPCS ij yxs iq”k cVu fLop }kjk
MPCS fLkLVe dks Reset djsasA iq”k
cVu dsk 5 lssds.M rd nckus ds ckn
fjyht djsasaA DJ Dykst djsasaA ;fn fQj
Hkh QkYV cuk jgrk gS rkss fjyhQ batu
dh ekWx djsasA
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
2nd In above case after the closing of DJ successfully with RDT output card inform the same to loco pilot with the following message: “System working with RDT output card. Inform TLC
Åij fy[ksa dsl es ;fn RDT
vkmViqV dkMZ }kjk DJ cUn gksrk gS rkss] yksdks ik;yV dks fuEufyf[kr
eSlst ds }kjk lwfpr fd;k tk,xk
djsasxk ^^flLVe RDT vkmViqV
dkMZ ds lkFk dk;Zjr~ gS] TLC dks
lwfpr djsaA
Page 33 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
88 DJ tripped due to internal fault in MPCS
Digital output card 2 failed
Fault Output card 2 or output card 3 or output card 4 has become defective. The exact nature of the fault shall be mentioned in the diagnostic message
1st Reclose DJ to resume Normal traction.
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
iqu% DJ cUn djsas lkekU; VªSD”ku
pkyw djsasaA
MPCS system related
89 DJ tripped due to internal fault in MPCS
Digital output card 3 failed
Fault 2nd
If do not succeed reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , reclose DJ. In case the fault persists call for Relief loco.
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
MPCS system related
90 DJ tripped due to internal fault in MPCS
Digital output card 4 failed
Fault
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
;fn lQyrk ugh feyrh gS rkss]
MPCS ;wfuV ij yxs fjlsV iq”k
cVu }kjk MPCS System dks
fjlsV djsasA iq”k cVu dks 5 ls- rd
nckdj j[ksaA mlds ckn gh fjyht
djsasaA DJ cUn djsasaA ;fn QkYV cuk
jgrk gS rkss fjyhQ batu dh ekWx
djsasaA
Page 34 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
91 DJ tripped due to internal fault in MPCS
Digital input card 1 failed
Fault Fault in digital input cards
1st Reclose DJ to resume Normal traction.
MPCS esa bUVjuy
QkYV }kjk DJ fVªi iqu%DJ cUn djsas lkekU; VªSD”ku
pkyw djsasaA
MPCS system related
92 DJ tripped due to internal fault in MPCS
Digital input card 2 failed
Fault 2nd
If do not succeed ,reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 3 seconds and release , recloseDJ. In case fault persists call for Relief loco.
MPCS esa bUVjuy
QkYV }kjk DJ fVªi MPCS system related
93 DJ tripped due to internal fault in MPCS
Digital input card 3 failed
Fault
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
MPCS system related
94 DJ tripped due to internal fault in MPCS
Digital input card 4 failed
Fault
;fn lQyrk ugh feyrh gS rkss]
MPCS ;wfuV ij yxs fjlsV iq”k
cVu }kjk MPCS System dks
fjlsV djsasA iq”k cVu dks 5 ls- rd
nckdj j[ksaA mlds ckn gh fjyht
djsasaA DJ cUn djsasaA ;fn QkYV cuk
jgrk gS rkss fjyhQ batu dh ekWx
djsasaA
MPCS esa bUVjuy
QkYV }kjk DJ fVªi MPCS system related
95 DJ tripped due to internal fault in MPCS
Digital input card 5 failed
Fault
MPCS esa bUVjuy
QkYV }kjk DJ fVªi MPCS system related
96 DJ tripped due to internal fault in MPCS
Digital input card 6 failed
Fault
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
MPCS system related
97 DJ tripped due to internal fault in MPCS
Digital input card 7 failed
Fault
MPCS esa bUVjuy
QkYV }kjk DJ fVªi MPCS system related
98 DJ tripped due to internal fault in MPCS
Digital input card 8 failed
Fault
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
Page 35 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
99 DJ tripped due to internal fault in MPCS
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
Input card 4 channel I-48 faulty
Fault
Wait for 5 Seconds and reclose DJ. Resume normal traction.
5 ls- rd bartkj djsas] rFkk DJ dks
cUn djsasaA lkekU; VªSD”ku pkyw djsasA
If do not succeed reset MPCS system by presiing the Push button switch located on MPCS unit, Press push button for 5ceconds and relese. Reclose DJ. In case the fault persists call for relief loco.
;fn lQyrk ugh feyrh gS rkss
MPCS ij yxs iq”k cVu fLop }kjk
MPCS fLkLVe dks RESET djsasA iq”k
cVu dsk 5 ls- rd nckus ds ckn
fjyht djsasA ;fn fQj Hkh QkYV cuk
jgrk gS rkss fjyhQ batu dh ekWx djsasaA
MPCS system related
100 Input card 4 channel I-49 faulty
Fault
MPCS system related
101 Input card 4 channel I-50 faulty
Fault
MPCS system related
102 Input card 4 channel I-51 faulty
Fault
MPCS system related
103 Input card 4 channel I-52 faulty
Fault
MPCS system related
104 Input card 4 channel I-53 faulty
Fault
MPCS system related
105 Input card 4 channel I-54 faulty
Fault
MPCS system related
106 Input card 4 channel I-55 faulty
Fault
Page 36 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
107
DJ tripped due to internal fault in MPCS
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
Input card 4 channel I-56 faulty
Fault
Wait for 5 Seconds and reclose DJ. Resume normal traction.
5 ls- rd bartkj djsas] rFkk DJ dks
cUn djsasaA lkekU; VªSD”ku pkyw djsasA
If do not succeed reset MPCS system by presiing the Push button switch located on MPCS unit, Press push button for 5ceconds and relese. Reclose DJ. In case the fault persists call for relief loco.
;fn lQyrk ugh feyrh gS rkss
MPCS ij yxs iq”k cVu fLop }kjk
MPCS fLkLVe dks RESET djsasA iq”k
cVu dsk 5 ls- rd nckus ds ckn
fjyht djsasA ;fn fQj Hkh QkYV cuk
jgrk gS rkss fjyhQ batu dh ekWx djsasaA
MPCS system related
108 Input card 4 channel I-57 faulty
Fault
MPCS system related
109 Input card 4 channel I-58 faulty.
Fault
MPCS system related
110 Input card 4 channel I-59 faulty
Fault
MPCS system related
111 Input card 4 channel I-60 faulty
Fault
MPCS system related
112 Input card 4 channel I-61faulty
Fault
MPCS system related
113 Input card 4 channel I-62 faulty
Fault
MPCS system related
114 Input card 4 channel I-63 faulty
Fault
Page 37 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
115 DJ tripped due to internal fault in MPCS
Working with one CPU
Fault 1st Resume normal traction by re closing DJ. Note down in the LOG book.
DJ iqu% CkUn djsa, lkekU; VªSD”ku
pkyw djsa rFkk ykWx cqd es uksV djsasA
MPCS esa bUVjuy
QkYV }kjk DJ fVªi
2nd In above case after the closing of DJ successfully with stand by CPU card inform the same to loco pilot with the following message: “System worksing with Standby CPU card” Inform TLC.
mijksDr dsl es DJ dks LVS.M ckbZ
CPU dkMZ }kjk lQyrk iwoZd cUn
djus ds Ik”pkr yksdks ik;yV dks
fuEufyf[kr eSlst crk;saA
flLVe LVsM okbZ CPU card ds }kjk dkZ;jr~ gS] TLC dks lwfpr
djsaA
MPCS system related
116 MPCS Communication Link Display 2 Fail
Information
The facility to wedge Q118, QCON, QCVAR & Q50 is disabled. Loco can run normally. Continue with normal traction & inform TLC.
The facility to wedge Q118, QCON, QCVAR & Q50 can be done from Display-1.Loco can run normally. Continue with normal traction & inform TLC.
MPCS dE;wfuds”ku
fyad fMLIys& 2 Qsy Q118, QCON, QCVAR rFkk Q-50 ost djsaus dh lqfo/kk
disabled gS, yksdks lkekU; :Ik ls
py ldrk gSA lkekU; VªSD”ku tkjh
j[ksa rFkk TLC dks lwfpr djsaA
Q118, QCON, QCVAR rFkk Q-50 dks fMLIys& 1 }kjk ost fd;k tk
ldrk gS, yksdks lkekU; :Ik ls py
ldrk gSA lkekU; VªSD”ku tkjh j[ksa
rFkk TLC dks lwfpr djsaA
Page 38 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
117 MPCS Communication Link Display 1 Fail Loco can run
Information
The facility to wedge Q118,QCON,QCVAR& Q50 is disabled. Loco can run normally. Continue with normal traction & inform TLC.
The facility to wedge Q118, QCON, QCVAR & Q50 can be done from Display-2.Loco can run normally. Continue with normal traction & inform TLC.
MPCS dE;wfuds”ku
fyad fMLIys& 1 Qsy]
yksdks py ldrk gS
Q118, QCON, QCVAR rFkk Q-50 ost djsaus dh lqfo/kk
disabled gS, yksdks lkekU; :Ik ls
py ldrk gSA lkekU; VªSD”ku tkjh
j[ksa rFkk TLC dks lwfpr djsaA
Q118, QCON, QCVAR rFkk Q-50 dksfMLIys& 2 }kjk ost fd;k tk
ldrk gS, yksdks lkekU; :Ik ls py
ldrk gSA lkekU; VªSD”ku tkjh j[ksa
rFkk TLC dks lwfpr djsaA
MPCS system related
118 Communication link of ISCU1 failed.
Information
Function of QD1 is disabled. Continue with normal traction and inform TLC.
dE;wfuds”ku fyad
ISCU1 Qsy QD-1 dk;Zjr ugh gSA lkekU;
VªSD”ku tkjh j[ksa rFkk TLC dks
lwfpr djsaA
MPCS system related
119 Communication link of ISCU-2 failed.
Information
Function of QD2 is disabled. Continue with normal traction and inform TLC.
dE;wfuds”ku fyad
ISCU2 Qsy QD-2 dk;Zjr ugh gS lkekU;
VªSD”ku tkjh j[ksa rFkk TLC dks
lwfpr djsaA
MPCS system related
120 Communication link of SCU failed.
Information
Put HBA off 5 seconds.
dE;wfuds”ku fyad SCU Qsy
HBA dks 5 ls- rd vkQ djsasA
Page 39 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
121 MPCS Power supply card 1 failed / not present
Information
Resume normal traction. Inform TLC.
MPCS ikoj lIykbZ
dkMZ&1 QsYM@ miyC/k
ugha gS
lkekU; VªSD”ku tkjh j[ksa rFkk TLC
dks lwfpr djsaA
MPCS system related
122 MPCS Power supply card 2 failed / not present
Information
Resume normal traction. Inform TLC.
MPCS ikoj lIykbZ
dkMZ&2 QsYM@ miyC/k
ugha gS
lkekU; VªSD”ku tkjh j[ksa rFkk TLC
dks lwfpr djsaA
MPCS system related
123 (No message to be displayed to the driver)
Remote diagnostics communication not OK
Information
MPCS system related
124
¼Pkkyd ds fy, fMLIys
ij dksbZ lwpuk ugha½
Remote diagnostics communication Recovered
Information
Page 40 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
125 DJ tripped due to VCB defective
DJ output wire or coil shorted with B-
Fault Reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , recloseDJ. In case the fault persists call for Relief loco.
VCB [kjkc gksus ds
dkj.k DJ fVªi
MPCS ;wfuV ij yxs fjlsV iq”k
cVu }kjk MPCS System dks
fjlsV djsasaA iq”k cVu dks 5 ls- rd
nckdj j[ksaA mlds ckn gh fjyht
djsasA DJ cUn djsasaA ;fn QkYV cuk
jgrk gS rkss fjyhQ batu dh ekWx
djsasaA MPCS system related
126 ICDJ via VCB defective
DJ output wire or coil shorted with B-
Fault Reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , recloseDJ. In case the fault persists call for Relief loco.
VCB [kjkc gksus ds
dkj.k ICDJ
MPCS ;wfuV ij yxs fjlsV iq”k
cVu }kjk MPCS System dks
fjlsV djsaasA i q”k cVu dks 5 ls- rd
nckdj j[ksA mlds ckn gh fjyht
djsasaA DJ cUn djsasaA ;fn QkYV cuk
jgrk gS rkss fjyhQ batu dh ekWx
djsaasA
Page 41 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
127 ICDJ via C118
(message for ARNO
loco)
SIV unable to pick
up.(message for SIV
loco)
C118/BLSI output wire or coil shorted with B-
Fault Corrective action for ARNO loco: Reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , recloseDJ. In case the fault persists call for Relief loco.
Corrective action for SIV loco: Reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , recloseDJ. In case the fault persists call for Relief loco.
C-118 }kjk ICDJ ¼vkuksZ yksdks ds fy,½
SIV dk fidvi u
gksuk
¼SIV yksdks ds fy,½
vkuksZ yksdks dks lgh djus dh
dk;Zokgh&MPCS ;wfuV ij yxs iq”k
cVu }kjk MPCS System dks
fjlsV djsasA iq”k cVu dks 5 ls- rd
nckdjsa j[ksA mlds ckn gh fjyht
djsasA DJ cUn djsasA ;fn QkYV cuk
jgrk gS rks fjyhQ batu dh ekWx
djsasaA
SIV yksdks dks lgh djsaus dh
dk;Zokgh&MPCS ;wfuV ij yxs iq”k
cVu }kjk MPCS System dks fjlsV
djsasA iq”k cVu dks 5 ls- rd nckdjsa
j[ksA mlds ckn gh fjyht djsasA DJ cUn djsasA ;fn QkYV cuk jgrk gS rkss
fjyhQ batu dh ekWx djsasaA
MPCS system related
128 Fault at line contactor L1,L2 & L3
L1,L2,L3 output wire or coil shorted with B-
Fault Isolate faulty TM by HMCS-1 Reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , reclose DJ. RESUME NORMAL TRACTION
Ykkbu dkUVsDVj L-1,
L-2 & L-3 esa QkYV
HMCS-1 }kjk nks’kiw.kZ VªSD”ku
eksVj dks vyx djsaasA MPCS ;wfuV ij yxs fjlsV iq”k cVu dks fjlsV
djsasa] iq”k cVu dks 5 ls- rd nckdj
j[kasA mlds ckn gh fjyht djsasaA DJ cUn djsaasA lkekU; VªSD”ku pkyw djsasaA
Page 42 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
129 Fault at line contactor L4,L5 & L6
L4,L5,L6 output wire or coil shorted with B-
Fault Isolate faulty TM by HMCS-2. Reset MPCS system by pressing the Push button switch located on MPCS unit. Press push button for 5 seconds and release , reclose DJ And resume normal traction.
Ykkbu dkUVsDVj L-4,
L-5 & L-6 esa QkYV
HMCS-2 }kjk nks’kiw.kZ VªSD”ku eksVj dks vyx djsasaA MPCS ;wfuV ij
yxs fjlsV iq”k cVu dks fjlsV djsas
iq”k cVu dks 5 ls- rd nckdjsa
j[ksA mlds ckn gh fjyht djsasA DJ cUn djsasA lkekU; VªSD”ku pkyw djsasA
MPCS system related
130 DJ tripped via C-107 contactor.
C107 output wire or coil shorted with B-
Fault If not welded or wedged then wedge/close C-107 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-107 dkUVsDVj }kjk
DJ fVªi
;fn csYM ;k ost ugh gS rkss C-107 dks vko”;d lko/kfu;k¡ j[krs
gq;s ost djsasA fMLIyss iSuy ij yxh
Soft Key }kjk Q118 dks ost
djds DJ dks iqu% cUn djsasA ukEkZy
VªSD”ku pkyw djsasA
Page 43 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
131 DJ tripped via C-106 contactor
C106 output wire or coil shorted with B-
Fault If not welded or wedged then wedge/close C106 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-106dkUVsDVj }kjk
DJ fVªi
;fn csYM ;k ost ugha gS rkss C-106 dks vko”;d lko/kfu;k¡ j[krs
gq;s ost djsasaA fMLIyss iSuy ij yxh
Soft Key }kjk Q-118 dks
ost djds DJ dks iqu% cUn djsasA
ukEkZy VªSD”ku pkyw djsaasA
MPCS system related
132 DJ tripped via C-105 contactor
C105 output wire or coil shorted with B-
Fault If not welded or wedged then wedge/close C-105 contactor manually after taking necessary precautions. Reclose DJ after wedging Q118 through soft key on display panel. Resume normal traction
C-105dkUVsDVj }kjk
DJ fVªi
;fn csYM ;k ost ugh gS rkss C-105 dks vko”;d lko/kfu;k¡ j[krs
gq;s ost djsasA fMLIyss iSuy ij yxh
Soft Key }kjk Q118 dks ost
djds DJ dks iqu% cUn djsasA ukEkZy
VªSD”ku pkyw djsasaA
Page 44 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
133 CP-1 not working C101 output wire or coil shorted with B-
Fault Work with CP-2 & CP-3.If it requires working of CP-1 also put HBA on 0 and wedge C-101
CP-1 dke ugha dj jgk CP-2 rFkk CP-3 }kjk dk;Z
djsasA ;fn CP-1 dks pykus dh
vko”;drk gS rkss HBA dks ‘0’ djsas
rFkk C-101 dks ost djsasA
MPCS system related
134 DJ tripped due to GR stuck up ON notches.
VE_DN output wire or coil shorted with B-
Fault Bring GR to 0 manually. Clear block section by operating GR manually and inform TLC.
GR ds ukWpst esa Qlus
ds dkj.k DJ fVªi gqvk
eSuqvyh GR dks ‘0’ ij djsasaA Cykd
lsD”ku dks GR ds eSuqvy vkijs”ku
ls Dyh;j djsasaA TLC dks lwfpr
djsaA
MPCS system related
135 Total Loss of Traction(TLTE) due to reverser not set as per MPJ position.
JFOR output wire or coil shorted with B-
Fault Operate reversers manually. Resume normal traction.
VSªD”ku VksVy ykWl
(TLTE), MPJ ds
iksft”ku ds vuqlkj
fjolZj lsV ugha gS
fjolZj dks eSuqvyh vkijsV djsasaA
lkekU; VªSD”ku pkyw djsasaA
MPCS system related
136 Total Loss of Traction(TLTE) due to reverser not set as per MPJ position.
JREV output wire or coil shorted with B-
Fault Operate reversers manually. Resume normal traction.
VSªD”ku VksVy ykWl
(TLTE), MPJ ds
iksft”ku ds vuqlkj
fjolZj lsV ugha gS
fjolZj dks eSuqvyh vkijsV djsasaA
lkekU; VªSD”ku pkyw djsasaA
Page 45 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
137 Total Loss of Traction(TLTE) due to CTF’s not set as per MPJ position.
CTF_RUN output wire or coil shorted with B-
Fault Operate CTF’s manually. Resume normal traction. Do not use DBR.
VSªD’ku esa VksVy ykWl
(TLTE), MPJ ds
iksft”ku ds vuqlkj
CTF’s lsV ugha gS
CTF’s dks eSuqvyh vkijsV djsasaA
lkekU; VªSD”ku pkyw djsaasA DBR dk
iz;ksx u djsasaA
MPCS system related
138 CP-2 not working C102 output wire or coil shorted with B
Fault Work with CP-1 & CP-3.If it requires working of CP-2 also put HBA on 0 and wedge C-102
CP-2 dke ugha dj jgk CP-1 rFkk CP-3 ls dk;Z
djsasA ;fn CP-2 dks pykus dh
vko”;drk gS rkss HBA dks ‘0’ djsasa
rFkk C-102 dks ost djsaasA
MPCS system related
139
GR not progressing
VE_UP output wire or coil shorted with B-
Fault Put ZSMGR on 0. Clear block section by operating GR manually.
GR vkxs ugh c< jgk ZSMGR dks ‘0’ ij djsasaA GR ds
eSuqvy vkijs”ku }kjk Cykd lsD”ku
Dyh;j djsaasA
MPCS system related
140
CP-3 not working
C103 output wire or coil shorted with B-
Fault Work with CP-1 & CP-2.If it requires working of CP-3also put HBA on 0 and wedge C-103
CP- 3 dke ugha dj
jgk CP-1 rFkk CP-2 ls dk;Z
djsasaA ;fn CP-3 pykus dh
vko”;drk gks rkss HBA dks ‘0’ ij djsasaA rFkk C-103 dks ost djsaaA
MPCS system related
141 Unloader not working.
VEUL output wire or coil shorted with B-
Isolation Inform TLC
vuyksMj dke ugh dj
jgk gS TLC dks lwfpr djsaA
Page 46 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
MPCS system related
142 EVPHGR not working
EVPHGR output wire or coil shorted with B-
Isolation Inform TLC
EVPHGR dke ugha
dj jgk TLC dks lwfpr djsaA
Traction Control circuit
143 SX1 not working
SX1 output wire or coil shorted with B-
Fault Inform TLC
SX1 dke ugha dj jgk TLC dks lwfpr djsaA
Traction Control circuit
144 SX2 not working
SX2 output wire or coil shorted with B-
Fault Inform TLC
SX2dke ugha dj jgk TLC dks lwfpr djsaA
Traction Control circuit
145 SX31 not working
SX31 output wire or coil shorted with B-
Fault Inform TLC
SX31 dke ugha dj
jgk TLC dks lwfpr djsaA
Traction Control circuit
146 SX32 not working
SX32 output wire or coil shorted with B-
Fault Inform TLC.
SX32 dke ugha dj
jgk TLC dks lwfpr djsaA
Traction Control circuit
147 brake applied due to defects in IP valve.
IP output wire or coil shorted with B-
Fault Isolate IP valve
IP OkkYo [kjkc gksus ds
dkj.k czsd yxkA
IP OkkYo dks vkbZlksysV djsaA
Traction Control circuit
148 VESA-2 not working
VESA-2 output wire or coil shorted with B-
Fault Inform TLC
VESA-2 dke ugha dj
jgk
TLC dks lwfpr djsaA
Page 47 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction Control circuit
149 PVEF defective
VEF output wire or coil shorted with B-
Fault Inform TLC
PVEF [kjkc gS TLC dks lwfpr djsaA
Traction Control circuit
150 VESA-1not working
VESA1 output wire or coil shorted with B-
Fault Inform TLC
VESA-1 dke ugha
djrk TLC dks lwfpr djsaA
Traction Control circuit
151 CTF(BRK) defective
CTF(BRK) output wire or coil shorted with B-
Fault Do not use DBR.
CTF ¼BRK½ [kjkc DBR dk iz;ksx u djsasaA
Traction Control circuit
152 DBR not working
C145 output wire or coil shorted with B-
Fault Do not use DBR.
DBR ds dke u djus
ij DBR dk iz;ksx u djsasaA
Traction Control circuit
153 LSDJ not working
LSDJ output wire shorted with B-
Fault work as per LSDJ on display.
LSDJ dke ugha dj
jgk Display esa n'kZk;s LSDJds vuqlkj
dk;Z djsasaA
Traction Control circuit
154 LSCHBA not working
LSCHBA output wire shorted with B-
Fault work as per LSCHBA on display.
LSCHBA dke ugha
dj jgk Display esa n'kZk; LSCHBA ds
vuqlkj dk;Z djsasaA
Traction Control circuit
155 LSGR not working
LSGR output wire or coil shorted with B-
Fault work as per LSGR on display
LSGR dke ugha dj
jgk Display esa n'kZk;s LSGR ds
vuqlkj dk;Z djsaasA
Page 48 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction Control circuit
156 LSB not working
LSB output wire or coil shorted with B-
Fault work as per LSB on display
LSB dke ugha dj jgk Display esa n'kZk;s LSB ds vuqlkj
dk;Z djsasaA
Traction Control circuit
157 LSP not working
LSP output wire or coil shorted with B-
Fault work as per LSP on display
LSP dke ugha dj jgk Display esa n'kZk;s LSP ds vuqlkj
dk;Z djsasaA
Traction Control circuit
158 LSRSI not working
LSRSI output wire or coil shorted with B-
Fault work as per LSRSI on display
LSRSI dke ugha dj
jgk Display esa n'kZk;s LSRSI ds
vuqlkj dk;Z djsasaA
Traction Control circuit
159 SX41 not working
SX41 output wire or coil shorted with B-
Fault inform TLC
SX41 dke ugha dj
jgk TLC dks lwfpr djsaA
Traction Control circuit
160 SX42 not working
SX42 output wire or coil shorted with B-
Fault inform TLC
SX42 dke ugha dj
jgk TLC dks lwfpr djsaA
Traction Control circuit
161 LSGROUP not working
LSGROUP output wire or coil shorted with B-
Fault work as per LSGROUP on display
LSGROUP dke ugha dj
jgk Display esa n'kZk;s LSGROUP ds
vuqlkj dk;Z djsaasA
Traction Control circuit
162 LSOL not working
LSOL output wire or coil shorted with B-
Fault work as per LSOL on display
LSOL dke ugha dj jgk Display esa n'kZk;s LSOLds vuqlkj
dk;Z djsaasA
Page 49 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction Control circuit
163 LSFL not working
LSFL output wire or coil shorted with B-
Fault work as per LSFL on display
LSFL dke ugha dj jgk Display esa n'kZk;s LSFLds vuqlkj
dk;Z djsaasA
Traction Control circuit
164 SON not working
SON output wire or coil shorted with B-
Fault inform TLC
SON dke ugha dj jgk TLC dks lwfpr djsaA
Traction Control circuit
165 Wire number 237 short circuit
Wire number 237 short circuit
Fault inform TLC
Okk;j ua0 237 'kkVZ lfdZV TLC dks lwfpr djsaA
Traction Control circuit
166 Wire number 259 short circuit
Wire number 259 short circuit
Fault inform TLC
Okk;j ua0 259 'kkVZ
lfdZV
TLC dks lwfpr djsaA
Traction Control circuit
167 QFL not working
QFL output wire or coil shorted with B-
Fault inform TLC
QFL dke ugha dj jgk TLC dks lwfpr djsaA
Traction Control circuit
168 DBR not working C108 output wire or coil shorted with B-
Fault Do not use DBR
DBRdke ugha dj jgk DBR dk iz;ksx u djsasaA
Traction Control circuit
169 GR not progressing GR not progressing
Fault Put ZSMGR in correct position and resume normal traction. If the problem persists put ZSMGR on 0.Clear block section by operating GR manually
GR izksxzslu ugha gks jgk ZSMGR dks lgh iksft”ku es djsaaas vkSj
lkekU; VªSD”ku pkyw djsaasA ;fn leL;k cuh
jgrh gS rkss ZSMGR dks ‘0’ ij djsas rFkk
GR ds eSuqvy dUVªksy }kjk Cykd lsD”ku
Dyhvj djsaasA
Page 50 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Traction Control circuit
170 Auto regression via line contactor L2 feedback open
Auto regression via line contactor L2 feedback open
Fault Isolate TM-2 by putting HMCS1 on 2
vkWVks fjxzs”ku ykbu dkUVsDVj
L-2 QhM cSd vksisu HMCS-1 dks 2 ij j[kdj,TM-2 dks dke
ls vyx djsasA
Traction Control circuit
171 Auto regression via line contactor L3 feedback open
Auto regression via line contactor L3 feedback open
Fault
Isolate TM-3 by putting HMCS-1 on 4.
vkWVks fjxzs”ku ykbu dkUVsDVj
L-3 QhM cSd vksisu HMCS-1 dks ^4* ij j[kdjsa,TM-3 dks
dke ls vyx djsasA
Traction Control circuit
172 Auto regression via line contactor L4 feedback open
Auto regression via line contactor L4 feedback open
Fault Isolate TM-4 by putting HMCS-2 on 2
vkWVks fjxzs”ku ykbu dkUVsDVj
L-4 QhM cSd vksisu HMCS-2 dks ^2* ij j[kdjsa,TM-4 dks
dke ls vyx djsasA
Traction Control circuit
173 Auto regression via line contactor L5 feedback open
Auto regression via line contactor L5 feedback open
Fault Isolate TM-5 by putting HMCS-2 on 3.
vkWVks fjxzs”ku ykbu dkUVsDVj
L-5 QhM cSd vksisu HMCS-2 dks ^3* ij j[kdjsa,TM-5 dks
dke ls vyx djsasA
General messages for driver
174 Select Panto Press BLDJ Press BLRDJ
Information
BLDJ open and BLRDJ pressed
LySDV isUVks
izsl BLDJ
izsl BLRDJ
175 CAB1 BL1 Key ON Information
BL1 KEY ON
dSc&1 BL1 Key vkWu
176 CAB2 BL2 Key ON Information
BL2 KEY ON
dSc&2 BL2 Key vkWu
177 CAB1 BL1 key OFF Information
BL1 key OFF
dSc&1 BL1 Key vkWQ
Page 51 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
178 CAB2 BL2 key OFF Information
BL2 key OFF
dSc&2 BL2 Key vkWQ
179 PANTO-1 raised Information
PANTO CAB1 raised
isUVks 1 mBk gksuk
180 PANTO-2 raised Information
PANTO CAB2 raised
isUVks 2 mBk gksuk
181 PANTO-1 Lowered Information
PANTO CAB1 lowered
isUVks 1 uhps gksuk
182 PANTO-2 Lowered Information
PANTO CAB2 lowered
isUVks 2 uhps gksuk
183 BLDJ ON Press BLRDJ to close DJ
Information
BLDJ closed
BLDJ vkWuDJ Dykst djus ds
fy, BLRDJ izsl djsa
184 BLDJ OFF
Information
BLDJ open
BLDJ vkWQ
General messages for driver
185 DJ CLOSED
Information
DJ CLOSED
DJ Dykst
186 BLRDJ Pressed but GR not in 0
Information
BLRDJ Pressed but GR not in zero
BLRDJ izsLM
ijUrq GR ^0* ij u gksuk
187 DJ open
Information
DJ OPENED
DJ vksisu
Page 52 of 52 Ammendment no. 1 issued on xx.08.2017 Technical Circular no. RDSO/2012/EL/TC/0119 Rev ‘1’
Prepared By Checked By Issued By
Subsystems
Diagnostic code
Message for Loco crew
Message stored for fault
diagnostic
Type of Message
Condition at the time
of fault
DJ closing attempt
Action-1 Action-2
Aux power circuit
188 CP-1 not working CP-1 not working due to C101 feedback fail
Fault Work with CP-2 & CP-3.If it requires working of CP-1 also put HBA on 0 and wedge C-101
CP-1 dke ugha dj jgh CP-2 ,Oka CP-3 ds lkFk dke djsasaA ;fn
CP-1 dh vko”;drk gS rkss HBA dks ‘0’ ij djsas rFkk C-101 dks ost djsasA
Aux power circuit
189 CP-2 not working CP-2 not working due to C102 feedback fail
Fault Work with CP-1& CP-3.If it requires working of CP-2 also put HBA on 0 and wedge C-102
CP-2dke ugha dj jgh CP-1,Oka CP-3 ds lkFk dke djsasaA ;fn
CP-2 dh vko”;drk gS rkss HBA dks ‘0’ ij djsas rFkk C-102 dks ost djsasA
Aux power circuit
190 CP-3 not working CP-3 not working due to C103 feedback fail
Fault Work with CP-1& CP-2.If it requires working of CP-3 also put HBA on 0 and wedge C-103
CP-3 dke ugha dj jgh CP-1 ,Oka CP-2 ds lkFk dke djsasA ;fn
CP-3 dh vko”;drk gS rkss HBA dks ‘0’ ij djsasa rFkk C-103 dks ost djsasaA