H3.50XM, H4.00XM-5, H4.00XMS-6, H4.00XM-6, H4.50XM, H5.00XM, H5.50XM

Equipment and weight:Weights (line 2.1) are based on the following specifications:Complete truck with Perkins 1004.42 diesel engine hydrostatic transmission, 3 100 mm Vista 2-stage limited free lift mast(H3.50XM-H4.00XMS-6) or 3 450 mm Vista 2-stage limited free lift mast (H4.00XM-6-H5.50XM), 1 201 mm hook type carriagewith load backrest and 1 220 mm forks, pneumatic shaped solid tyres, overhead guard and load backrest extension.

Fuel tank capacity:H3.50XM-H4.00XMS-6: 69 litresH4.00XM-6-H5.50XM: 103 litres

Forks:H3.50XM-H4.00XMS-6: 50 x 125 x 1 220 to 1 800 mm longH4.00XM-6-H5.50XM: 60 x 150 x 1 220 to 1 800 mm long

Fork spacing:Inside to inside, minimum: 135 mm (H3.50XM-H4.00XMS-6) 160 mm (H4.00XM-6-H5.50XM)Outside to outside, maximum: 1 105 mm (H3.50XM-H4.00XMS-6) 1 109 mm (H4.00XM-6-H5.50XM)

NOTE:Specifications are affected by the condition of the vehicle and how it isequipped, as well as the nature and condition of the operating area. If thesespecifications are critical, the proposedapplication should be discussed with yourdealer.

! Add 49 mm with load backrestextension

¶ Bottom of forks

� Stacking aisle width (lines 4.33 & 4.34) are based on the V.D.I. standard calculation as shown on illustration. The British Industrial Truck Association recommends the addition of 100 mm to the total clearance (dimension a) for extra operating margin at the rear of the truck.

† Gradeability figures (lines 5.7 & 5.8) are provided for comparison of tractive performance, but are not intended to endorse the operation of the vehicle on the stated inclines. Follow instructions in the operating manual regarding operation on inclines.

" Noise level based on the weighting values contained in EN12053

# Noise level measured according to 2000/14/EC directive

Mast tables:

! 6° Back tilt required

" Lowered height lower than overhead guard height

� Add 471 mm with load backrest extension

� Add 423 mm with load backrest extension

" Deduct 423 mm with load backrest extension

# Add 389 mm with load backrest extension

$ Add 334 mm with load backrest extension

! Deduct 334 mm with load backrest extension

% Wide tread or dual drive wheels required

$ Consult your Hyster lift truck dealer.

Load centre (mm)

Rate

d l

oad

(kg

)

H5.50XMH5.00XMH4.50XMH4.00XM-6H4.00XM-5H3.50XM

Load centre

Distance from front of forks to centre of

gravity of load.

Rated load

Based on vertical masts up to 4 300 mm

(H3.50XM, H4.00XM-5, H4.00XMS-6) or

4 050 mm (H4.00XM-6, H4.50XM,

H5.00XM) to top of forks. Safety:This truck conforms to the current EU requirements.

Hyster, , , Monotrol, Vista, Challenger

and SpaceSaver are trademarks of Hyster Company.

Hyster products are subject to change without notice.

Lift trucks illustrated may feature optional equipment.

= Centre of gravity of unladen truck

Ast = Wa + x + l6 + a (see lines 4.33 & 4.34)

a = Minimum operating clearance

(V.D.I. standard = 200 mm BITA recommendation = 300 mm)

l6 = Load length

Mast and capacity information

HighliftsThe rated capacities shown are for trucks equipped with standard or sideshift carriage, and nominal length forks(see below). Masts above the maximum fork height shown here are classified as high lift, and depending on thetyre/tread configuration may require reduced capacity, restricted back tilt or wide tread.

WarningCare must be exercised when handling elevated loads. When the carriage and/or load is elevated, truck stabilityis reduced. It is important that mast tilt in either direction be kept to a minimum when loads are elevated.Operators must be trained and adhere to the instructions contained in the Operating Manual.

Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England

Hyster Europe, Nijverheidsweg 29, 6541 CL Nijmegen, The Netherlands

Hyster Europe, Portland Road, Irvine, Ayrshire KA12 8JG, Scotland

Hyster Europe, Via Confalonieri 2, 20060 Masate (MI), Italy

http://www.hyster.co.uk

01/03/202 Printed in England Form No. 871408 Rev. 2

A division of NACCO Materials Handling Limited.

FPOFPO

High lift masts require approval from Hyster based on specific application information. This information should besupplied on Hyster form 857025-25, and will be used to determine rated capacities to be included on a specificnameplate. The completed nameplate must be installed on the truck before it is put to use.

H3.50-5.50XMHydrostatic models

Diesel powered forklifts. 3 500 to 4 000 kg @ 500 mm & 4 000 to 5 500 kg @ 600 mm

Built to lastThe latest generation of 3,5 to 5,5 tonne Hyster lift are built to perform in heavy duty applications, offeringdurability and power combined with the best in operator comfort. Trucks that will meet your needs for highproductivity, economy and ease of service.

Complete comfort and smooth operationThe adjustable steering column and full suspension seat allows operators to select the most comfortable driving positions. Flip-up, adjustable armrest provides easy on/off access and reduces fatigue during hydrauliclever operation. Power steering and the optional Monotrol pedal promote operator productivity while thehydrostatic transmission reduces driver effort by virtually eliminating the need for braking.

For all weather protection you can choose a fully integrated cab designed for enhanced comfort.

317 mm x 60 mm and 317 mm x 63 mm automotive type brakes are vacuum-assisted, self adjusting and self-energising.

Performance with low maintenanceHydrostatic models feature the Perkins 1004.42 diesel engine. A maximum Peak torque of 290 Nm is producedat just 1 400 rpm and delivered through the Hyster-engineered hydrostatic drive, giving impressive gradeability,acceleration and travel speed performance.

An advanced control system allows the hydrostatic motors to make use of 100% of available engine power.

A throttle-up system optimises the performance of hydraulic functions.

With a displacement of 4,23 litre, the Perkins 1004.42 engine is designed for low emissions, low fuel consumptionand easy maintenance.

The integrated cooling system for engine, hydrostatic transmission and hydraulic system has an easy-to-clean,open fin radiator. The hydrostatic oil reservoir has temperature and level sensors connected to the dash display.

The 30,4 litre fluid capacity hydraulic system has a double gear main pump and full-time, full-flow, 10-micronreturn line filter.

Extra versatilityThe Hyster range of Vista 2-stage limited and full-free lift and 3-stage full free lift masts are designed for goodvisibility and smooth, durable operation. 2-stage masts have flush-faced channels to reduce chance of loaddamage during operation. Hyster masts have hydraulic cushioning for optimal load control and reduced noise.For reliability and protection all hoses are routed inside the mast construction.

FPO