Extra-Large Horizontal Turning Center

Hi-TECH 700Extra-Large Horizontal Turning Center

HS-T073-R6.36-20190116

HIGH PERFORMANCE

EXTRA-LARGE TURNING CENTER

Hi-TECH 700 has a integrated 45-degree slant bed frame to minimize heat distortion, all guide way are designed as solid Box guide ways to

maintain rigidity and precision even during prolonged operations. Its automatic transmission system allows low-speed, high-torque turning as

well as high-speed machining, Hwacheon's advanced, patented design prevents deterioration of the workpiece from thermal displacement.

The jet of lubrication is constantly applied to the spindle bearing for lubrication and cooling, to increase the machine's life and the precision in

machining.

heavy-duty turning

※ Main Features

1. Best structure for Heavy Duty Cutting

Spindle Motor

- Std.: 37/30kW(50/40HP)

- Opt.: 45/37kW(60/50HP)

Max. Cutting Diameter: Ø 650mm

Max. Cutting Length: 1,986mm

2. Reducing lead time

Rapid Speed (X/Z): 18m/miin

3. Tailstock (MT #5)

Quill Dia.: Ø 150mm

Powerful Built-in Quill structure

4. Multi Function

Tailstock Body Program (Std.)

Automatic Tool Presetter (Opt.)

HS-T073-R6.26-20180405

Hi-TECH 700

Hi-TECH 700 / MCHi-TECH 700 / Std.

Ref. 1) Std.: with tailstock 2) MC: Turnmill with C-Axis(0.0001˚)

Machine Line-UpHS-T073-R1.3-20170403

Hi-TECH 700

700/MC

Item Hi-TECH 700 Hi-TECH 700/MC

Capacity

Swing over bed mm(inch) Ø 900 (35.43”)

Max. Cutting diameter mm(inch) Ø 680 (26.77”)

Standard Cutting diameter mm(inch) Ø 387 (15.23”)

Max. Cutting length mm(inch) 1,986 (78.18”) 1,866 (73.46”)

Chuck Size inch 15"

Spindle

Type of spindle nose ASA A2-11

Max. spindle speed rpm 1,800

Through spindle hole diameter mm(inch) Ø 132 (5.2”)

Max. Bar Size mm(inch) Ø 116 (4.56”)

Spindle bearing inner diameter mm(inch) Ø 180 (7.09”)

Spindle motor kW(HP) 37/30 (50/40)

Turret

Number of tool station ea 12

Tool size mm(inch) □ 32 × Ø 60 (□1.25” × Ø2.5”)

Turret indexing time sec/step 0.4

Axes

Rapid speed (X/Z) m/min(ipm) 18/18

Max. Stroke (X/Z) mm(inch) 360/2,050 (14.17”/80.70”)

Feed Motor (X/Z) kW(HP) 6/6 (8/8)

Machine Specification【Hi-TECH 700】HS-T073-R6.24-20190116

Item Hi-TECH 700 Hi-TECH 700/MC

Tailstock

Quill Dia. mm(inch) Ø 150 (5.9”)

Quill Stroke mm(inch) 150 (5.9”)

Quill Taper MT # 5

Turnmill (Opt.)

Spindle motor kW(HP) ㅡ 7.5/5.5 (10/7.5)

Max. spindle speed rpm ㅡ 2,000

Max. Drill/Tap size mm/(inch) ㅡ Ø 32 (Ø1.26”) / M24

Min. index angle o(deg) ㅡ 0.0001˚

Tank

Lubrication ℓ(gal) 12 (3.2)

Hydraulic ℓ(gal) 50 (13.2)

Coolant ℓ(gal) 300 (79)

Power Sources

Electrical power supply kVA 75

Dimension

Height mm(inch) 2,535 (99.8”)

Floor space (L×W) mm(inch) 5,065x2,282 (199.41”x89.84”)

Weight kgf (lbf) 17,350(38,250) 17,500(38,581)

NC Controller Fanuc 0i-TF

Machine Specification【Hi-TECH 700】HS-T073-R6.24-20190116

Item Specification Std. MC

Controlled axis

Controlled axis (Cs axis) 2-axes 2-axes 3-axes

Simultaneously controlled axes 2-axes 2-axes 3-axes

Least input increment0.001mm, 0.0001deg,

0.0001inchS S

Least input increment 1/10 0.0001mm, 0.00001inch O O

inch/metric conversion G20, G21 S S

Stored stroke check 1 S S

Stored stroke check 2,3 S S

Chamfering on/off S S

Backlash compensation S S

Operation

Automatic & MDI operation S S

Program number search S S

Sequence number search S S

Dry run, single block S S

Manual handle feed 1unit S S

Manual handle feed rate x1, x10, x100 S S

Interpolation function

Positioning G00 S S

Linear interpolation G01 S S

Circular interpolation G02, G03 S S

Dwell (Per seconds) G04 S S

Polar coordinate interpolation G12.1/G13.1 ㅡ S

Cylindrical interpolation G7.1 ㅡ S

Threading G32 S S

Multiple threading S S

Threading retract S S

Continuous threading S S


Interpolation function

Variable lead threading G34 S S

Ref. position return 1st G28 S S

Ref. position return check G27 S S

2/3/4th Ref. position return G30 S S

Arbitrary Speed Threading O O

Feed function

Rapid traverse override F0, F25, F50, F100 S S

Feed per minute (mm/min) G98 S S

Feed per revolution (mm/rev) G99 S S

Rapid traverse bell-shaped acceleration/deceleration S S

Feedrate override 0-150% S S

Jog feed override 0-1,260 mm/min S S

Program input

Tape code EIA / ISO S S

Optional block skip 9ea S S

Program number O4-digits S S

Sequence number N8-digits S S

Decimal point programming S S

Coordinate system setting G50 S S

Coordinate system shift S S

Workpiece coordinate system (G54-G59) S S

Workpiece coordinate system preset (G92.1) S S

Direct drawing dimension programming S S

G code system A S S

※ㅡ : Not available S: Standard O: Option

NC Specification【Fanuc 0i-TF】HS-T073-R4.9-20180405


Program input

Programmable data input G10 S S

Sub program call 10 folds nested S S

Custom macro B S S

Addition of custom macro common variables

#100-#199,

#500-#999S S

Canned cycles S S

Multiple repetitive cycle S S

Multiple repetitive cycle Ⅱ S S

Canned cycles for drilling S S

Manual guide i S S

Spindle speed function

Constant surface speed control G96/G97 S S

Spindle override 50-120% S S

Spindle orientation S S

Rigid tapping O S

Spindle synchronous control ㅡ ㅡ

Tool function / compensation

Tool function T4-digits S S

Tool offset pairs 128pairs S S

Tool nose radius compensation S S

Tool geometry/wear

compensationS S

Tool life management O O

Automatic tool offset Tool Presetter option is

requiredS S

Direct input tool offset value measured B

Tool Presetter option is

requiredS S


Editing operation

Part program storage length 1,280m(512kB) S S

Number of register able programs

400ea S S

Background editing S S

Extended part program editing S S

Play back S S

Operation/DisplayClock function S S

Self-diagnosis function S S

Alarm history display S S

Help function S S

Run hour and parts count display S S

Graphic function S S

Dynamic graphic display O O

Multi-language display (English, German, French, Italian, Chinese, Spanish, Korean, Portuguese, Polish, Hungarian, Swedish, Russian)

S S

Data input/output

Reader/Puncher interface CH1 RS232C S S

Reader/Puncher interface CH2 RS232C S S

Ethernet interface S S

Memory card interface S S

USB card interface S S

Others

Display unit 10.4" color LCD S S

NC Specification【Fanuc 0i-TF】


HS-T073-R4.9-20180405


Controlled axis

Control C axes 2-axes 2-axes 3-axes

Simultaneous controlled axes 2-axes 2-axes 3-axes

Interpolating axes 3-axes 3-axes 3-axes

Least input increment0.001mm, 0.0001deg,

0.0001inchS S

Least input increment 1/10 0.0001mm, 0.00001inch O O

Working area limit function S S

Software traverse limit S S


Feed override 0~120% S S


Manual Hand wheel feed rate x1, x10, x100 S S

Number of Manual Hand wheel 1 unit S S

Operation

Operating panel size 1 Channels S S

Number of channels / mode group 1 Channels S S

Inch/Metric conversion G70, G71 S S

Block search function S S

Program control (dry run, skip block,machine lock)

S S

CompensationMeasuring system and spindle

compensationS S

Backlash compensation S S


Axis function

Travel to fixed stop with forced control S S

Acceleration with jerk limitation S S

Advanced Position control S S

Dynamic Pre control S S

Dynamic servo control in the drive S S

Feed function


Feed per minute (mm/min) G94 S S

Feed per revolution (mm/rev) G95 S S

Feedrate override 0-120% S S


CNC programming

SINUMERIK Program Guide Siemens G-code (DIN66025) S S

Online ISO dialect interpreter S S

CNC editor with editing functions Marking, copying, deleting S S

Absolute/Incremental dimension G90, G91 S S

Working area limitation G25, G26 S S

Exact stop G60, G9 … S S

Programmable rotation ROT, AROT S S

Programmable scale factor SCALE, ASCALE S S

Programmable mirroring MIRROR, AMIRROR S S


NC Specification【Siemens 828D】【Option】HS-T073-R4.9-20180405


CNC programming

Subroutine levels and interrupt routines, max. 16/2 S S

Number of zero offset 100 EA (G54..) S S

User parameter R-parameters (300) S S

Turning cycle Cycle93 ~ 97 S S

Drilling cycle Cycle81 ~ 82 S S

Technology cycles for drilling/milling S S

Technology cycles for turning ㅡ S

Pocket milling with free contour

definition and islandsS S

Shop Turn S S

Spindle speed function

Constant surface speed control G96/G97 S S

Spindle override 0-120% S S

Spindle orientation M19 S S

Rigid tapping O S

Spindle synchronous control ㅡ ㅡ

Tool management

Tool function T-number S S

Number of tool / edges 256/512 S S

Tool nose radius compensation S S

Tool geometry/wear compensation S S

Replacement tools for tool management O O

Automatic tool offset Tool Presetter option is

requiredS S

Direct input tool offset value measured B

Tool Presetter option is

requiredS S


Diagnosis

On board on-line help system S S

On board servo optimization S S

On board signal, bus, network diagnosis S S

Alarm history display / download S S

Operation/Display

Timer & Counter function S S

Screen saver S S

Alarm history display S S

Help function S S

Easy program selection S S

Graphic simulation S S

Multi-language display (Chinese, Simplified, English, French, German, Italian, Spanish)

S S

Help for programming, alarms and machine data, expandable S S

Data management

CNC User memory 5MB 5MB

CF card interface CF card S S

USB interface USB S S

CF card 1GB , 2GB , 4GB O O

Ethernet interface S S

Others

Display unit 10.4" color LCD S S

KeyboardIntegrated QWERTY

keyboardS S

NC Specification【Siemens 828D】【Option】


HS-T073-R4.9-20180405

Item ExplanationControl Axes X,Z, C Axis)

Increment system

Least input increment

X, Z-Axis : 0.001 mm

C-Axis : 0.0001°

X-Axis : 0.0005 mm (Radial value)

Least command increment

X-Axis : 0.0005 mm

Z-Axis : 0.001 mm

Maximum command value ± 9999.999 mm

Program memory capacity 1,280M(512kB)

Part program edit

Part program editing as follows is possible by MDI operation.

1) Insert, Alter, Delete of word.

2) Delete of block or until the block designated.

3) Register, delete of program.

Input format

Block, word, address, format, can be altered (inch format)

N4 G2 X(U)4.3 R(C)4.3 I4.3 C(H)4.3 K4.3 F3.4 B4.3 or S4, T4(2.2)

M2 or 3 P4(7) Q4

Decimal point editThe following addresses can be used with a decimal point: X, Z, U,

W, R, C, F, I, K, A, H, B

Command method Absolute / Incremental command is possible

PositioningEach axis can independently feed rapidly and position by G00

command

Cutting federate

Feed per minute and feed per spindle revolution is possible.

G98 : Feed per minute. (mm/min)

G99 : Feed per revolution. (mm/rev)

Feed rate range (Feed override 0 - 150% every 10%)

Feed per minute 0 - 1,260 (mm/min)

Feed per revolution 0.001 - 2,000 (mm/rev)

Auto acceleration

/deceleration Rapid Feed : Linear type acceleration/deceleration

Cutting Feed : Exponential acceleration/deceleration

Coordinate system setting By means of this command, a certain position of the tool for

example, a coordinate system whereby the tip of the cutting edge

becomes (X,Z) of the coordinate system.

This coordinate is called as work coordinates.

Item ExplanationAutomatic coordinate

settingBy means of this command, a certain position of the tool for




Work coordinate system

shiftWhen the coordinate system actually set by the G50 command or

the automatic coordinate system setting deviate from the

programmed work coordinate system, the set coordinate system

can be shifted

Reference point return 1) Manual reference point return.

2) Automatic reference point return (G27, G28).

Interpolation functionLinear interpolation : Done by G01 command at feed rate code

designated.

Circular interpolation : Any circular arc is interpolated by G02 or

G03, at feed rate F code designated.

G02 : Clockwise. G03 : Counter Clockwise.

When circular radius is command as R, any circular arc of 0°-

180°is interpolated, and when circular radius is command as

address I, K., any circular interpolation of 0°- 360°can be

command

Thread cutting Can be cut using a G32 command in addition to equal lead.

1) Straight thread. 2) Tapered thread.

3) Scroll thread

Dwell Dwell is executed by the P, U, X commands. Setting Range 0 -

999.999 sec. Decimal point be used with P address

Back lash compensation This function compensations for lost motion of the machine.

Compensation value (0-2,550 mm) is set by parameter, for each

axis (by least command increment).

MDI & LCD All kinds of data information is input and displayed such as LCD

character display, program alarm, diagnosis program, etc.,

Program No. search Program number of 4 digit continuous to 0 is searched by MDI &

LCD Panel

Sequence No. search Sequence number in the program selected by MDI & LCD is

searched. (word is also searched by the same way in edit mode.)

Miscellaneous function

(M function)

By the command of 3 digit figure after the address M, ON/OFF

control from the machine is possible. Only one M code can be

command per block

NC Instruction【Fanuc 0i-TF】HS-T073-R4.6-20180405

Item ExplanationSpindle function

(S function)

Spindle speed is commanded by the 4-digit figure to address S.

When this function is used with G96,it means cutting speed.

When with G97, it means rpm

Tool function

(T function)

Turret position can be selected and tool position offset can be

done by the command of 2 digits after the address T

Tool position offset Designating the number of tool position offset by the 2 lower digits

of the 4 digits address T, can make tool wear offset possible.

Offset pairs are 128, offset amount is ranging 0 ± 999.999 mm

Dry run Feed rate becomes jog speed (for both cutting feed and for rapid

moves).

Single block Program can be executed one step at a time

Optional block skip Turning on the optional block skip switch ignores the block

including "/" code at the beginning.

Machine lock When the switch is set to the Machine Lock position, move

command pulses are suppressed. Consequently the display is

updated as specified by the program, but the tool does not move.

The M, S, T and 2nd auxiliary function are executed. This function

is used to check a program

Feed hold Input/output of alarm display can be signaled by pressing alarm,

DGNOS key of MDI panel

Stored stroke limit 1 An area inside the area set by parameter is deemed as prohibited

area, when stroke is commanded into this area, this function

makes the axis decelerate and stop than OT alarm displayed

Canned cycles 1) G90 : Cutting Cycle A --- Outer

diameter/internal diameter cutting

2) G92 : Thread Cutting Cycle

3) G94 : Cutting Cycle B --- End face turning cycle

Constant surface speed

control

By the direct command of surface speed by S4-digit makes the

motor rpm to be controlled continuously so that cutting speed of

spindle can be constant, in spite of the alteration of tool position.

G96 : Constant surface speed control is executed.

G97 : Constant surface speed control is not executed

Multiple repetitive cycle (1) G70 : Finishing Cycle

(2) G71 : Stock removal in turning.

(3) G72 : Stock removal in facing.

(4) G73 : Pattern repeating.

(5) G74 : End face peck drilling cycle.

(6) G75 : Outer diameter/internal diameter drilling cycle.

(7) G76 : Multiple thread cutting cycle

Item ExplanationTool nose radius

compensation

G40 : Tool nose radius compensation cancel.

G41 : Moving on the left side of the programmed path.

G42 : Moving on the right side of the programmed path.

Maximum offset value: + 999.999 mm

Chamfering & corner R In case of linear cutting perpendicular to or parallel with the axis,

when next command is chamfering or corner R, linear cutting,

chamfering or corner R cutting is accomplished by commanding one

block

Portable tape reader Program, Parameter and etc., are used for reading out of NC

inch / Metric conversion inch system and Metric system are selected to input by G code

cutting

G20 : inch input. G21 : Metric input

Changing of tool offset

amountOffset value can be set program command (G10).

Custom macro Having registered macro commands as sub program, in memory.

This function is able to recall at anytime the NC command program

by this simple procedure

Additional program

memoryImpossible (Max. 1,280M(512kB)

External tool

compensation

This is the function to offset the tool offset value from out side the

CNC. Offset value is automatically added to the input data of NC

Additional tool offset This number of tool position offsets and tool nose R, compensation

is maximum 128 pairs.

Tool geometry offset and

tool wear offset

This is a special type of tool offset, offset value regarding tool

installing position (geometry) and offset value regarding tool wear

offset, both are stored and tool offset is done accordingly. Offset

pairs are 128 pairs each.

Run hour display 2 items, moving time and the number of parts are displays on the

position screen.

Part counter : The total number of parts are displayed . . . counted

by either M02, M03.

Run hour : Accumulated running to hour display . . . accumulated

running to hour of automatic operation.

Cycle time : Cycle time display . . . Running hour display of one

automatic cycle.

Solid tapping When tapping, high speed and high accuracy tapping can be done

by running the spindle and X, Z axis synchronous

NC Instruction【Fanuc 0i-TF】HS-T073-R4.6-20180405

Item ExplanationControl Axes X,Z, C Axis

Increment system

Least input increment

X, Z-Axis : 0.001 mm

C-Axis : 0.0001°

X-Axis : 0.0005 mm (Radial value)

Least command increment

X-Axis : 0.0005 mm

Z-Axis : 0.001 mm

Maximum command value ± 9999.999 mm

Program memory capacity 5MB

Part program edit

Part program editing as follows is possible by MDA operation.

1) Insert, Alter, Delete of word.

2) Delete of block or until the block designated.

3) Register, delete of program.

Input formatBlock, Auxiliary Command, Coordinate Axis, Interpolation

Parameter, Feed, Speed, Tool, Misc Function.

Decimal point edit The following addresses can be used with a decimal point

Command method Absolute / Incremental command is possible

PositioningEach axis can independently feed rapidly and position by G00

command

Cutting federate

Feed per minute and feed per spindle revolution is possible.

G94 : Feed per minute. (mm/min)

G95 : Feed per revolution. (mm/rev)

Feed rate range (Feed override 0 - 120%)

Feed per minute 0 - 1,260 (mm/min)

Feed per revolution 0.001 - 2,000 (mm/rev)

Auto acceleration

/deceleration Rapid Feed : Linear type acceleration/deceleration

Cutting Feed : Exponential acceleration/deceleration

Coordinate system setting By means of this command, a certain position of the tool for




Item ExplanationAutomatic coordinate

settingBy means of this command, a certain position of the tool for




Work coordinate system

shiftWhen the coordinate system actually set by the G50 command or

the automatic coordinate system setting deviate from the

programmed work coordinate system, the set coordinate system

can be shifted

Reference point return 1) Manual reference point return.

2) Automatic reference point return (G74).

Interpolation functionLinear interpolation : Done by G01 command at feed rate code

designated.

Circular interpolation : Any circular arc is interpolated by G02 or

G03, at feed rate F code designated.

G02 : Clockwise. G03 : Counter Clockwise.

When circular radius is command as R, any circular arc of 0°-

180°is interpolated, and when circular radius is command as

address I, K., any circular interpolation of 0°- 360°can be

command

Thread cutting Can be cut using a G33/34/35 command in addition to equal lead.

1) G33 : Thread cutting with constant lead

2) G34 : Thread cutting with linear increasing lead

3) G35 : Thread cutting with linear decreasing lead

Dwell Dwell is executed by G04 F commands. Setting Range 0 - 999.999

sec.

Back lash compensation This function compensations for lost motion of the machine.

Compensation value (0-2,550 mm) is set by parameter, for each

axis (by least command increment).

MDI & LCD All kinds of data information is input and displayed such as LCD

character display, program alarm, diagnosis program, etc.,

Block search Program number of 4 digit continuous to 0 is searched by MDI &

LCD Panel

Sequence search Sequence in the program selected by MDI & LCD is searched.

(word is also searched by the same way in edit mode.)

Miscellaneous function

(M function)

By the command of 3 digit figure after the address M, ON/OFF

control from the machine is possible. Only one M code can be

command per block

NC Instruction【Siemens 828D】【Option】HS-T073-R4.6-20180405

Item ExplanationSpindle function

(S function)

Spindle speed is commanded by the 4-digit figure to address S.

When this function is used with G96,it means cutting speed.

When with G97, it means rpm

Tool function

(T function)

Turret position can be selected and tool position offset can be

done by the command of 2 digits after the address T

Tool position offset Designating the number of tool position offset by the 2 lower digits

of the 4 digits address T, can make tool wear offset possible.

Offset pairs are 64, offset amount is ranging 0 ± 999.999 mm

Dry run Feed rate becomes jog speed (for both cutting feed and for rapid

moves).

Single block Program can be executed one step at a time

Optional block skip Turning on the optional block skip switch ignores the block

including "/" code at the beginning.

Machine lock When the switch is set to the Machine Lock position, move

command pulses are suppressed. Consequently the display is

updated as specified by the program, but the tool does not move.

The M, S, T and 2nd auxiliary function are executed. This function

is used to check a program

Feed hold Input/output of alarm display can be signaled by pressing alarm,

DGNOS key of MDI panel

Stored stroke limit An area inside the area set by parameter is deemed as prohibited

area, when stroke is commanded into this area, this function

makes the axis decelerate and stop than OT alarm displayed

Constant surface speed

control

By the direct command of surface speed by S4-digit makes the

motor rpm to be controlled continuously so that cutting speed of

spindle can be constant, in spite of the alteration of tool position.

G96 : Constant surface speed control is executed.

G97 : Constant surface speed control is not executed

Technical cycles TURNING

(1) Centering : (CYCLE81) (2) Drilling : (CYCLE82)

(3) Reaming : (CYCLE85) (4) Boring : (CYCLE86)

(5) Deep-hole drilling : (CYCLE78) (6) Cut-off : (CYCLE92)

(7) Thread Turning: (CYCLE99)

Milling

(1)Face Milling : (CYCLE61) (2) Rectangular Pocket : (POKET3)

(3)Rectangular spigot : (CYCLE76) (4)Multi-edge : (CYCLE79)

(5)Open groove : (CYCLE899) (6)Thread Milling : (CYCLE70)

(7)Path Milling : (CYCLE72) (8) Contour Pocket : (CYCLE63)

Item ExplanationTool nose radius

compensationG40 : Tool nose radius compensation cancel.

G41 : Moving on the left side of the programmed path.

G42 : Moving on the right side of the programmed path.

Maximum offset value: + 999.999 mm

Chamfering & corner R In case of linear cutting perpendicular to or parallel with the axis,

when next command is chamfering or corner R, linear cutting,

chamfering or corner R cutting is accomplished by commanding one

block

Portable tape reader Program, Parameter and etc., are used for reading out of NC

inch / Metric conversion inch system and Metric system are selected to input by G code

cutting

G70 : inch input. 71 : Metric input

Changing of tool offset

amountProgrammable tool offset (TOFFL, TOFF, TOFFR)

Custom macro Having registered macro commands as sub program, in memory.

This function is able to recall at anytime the NC command program

by this simple procedure

Additional program

memoryPossible (Option Max. 100MB)

External tool

compensation

This is the function to offset the tool offset value from out side the

CNC. Offset value is automatically added to the input data of NC

Tool geometry offset and

tool wear offset

This is a special type of tool offset, offset value regarding tool

installing position (geometry) and offset value regarding tool wear

offset, both are stored and tool offset is done accordingly. Offset

pairs are 64 pairs each.

Run hour display 2 items, moving time and the number of parts are displays on the

position screen.

Part counter : The total number of parts are displayed . . . counted

by either M02, M03.

Run hour : Accumulated running to hour display . . . accumulated

running to hour of automatic operation.

Cycle time : Cycle time display . . . Running hour display of one

automatic cycle.

Solid tapping When tapping, high speed and high accuracy tapping can be done

by running the spindle and X, Z axis synchronous

NC Instruction【Siemens 828D】【Option】HS-T073-R4.6-20180405

Standard Accessories

1) Air Blower

2) Air Gun

3) Bar Feeder Interface

4) Chip Conveyor & Box, Side Type

5) Chuck Clamp/Unclamp Confirm Switch

6) Chuck Pressure Check Switch

7) Chuck Pressure Compensation

8) Coolant Gun

9) Dual Pressure (Chuck)

10) High Pressure Coolant, 0.6/ 1.5/ 3/ 7 MPa

11) Hydraulic Chuck, 18“/ 21”/ 24”

12) Hydraulic Steady Rest Base Set

13) Hydraulic Steady Rest Set

14) Lathe-Hwacheon Tool Load Detect (L-HTLD)

15) NC Cooler

16) Oil Skimmer

17) Set of Hard Jaws, 15“/ 18“/ 21“/ 24"

18) Spindle Motor Upgrade, 45/37kW (60/50HP)

19) Tool & Work Counter, External/ Internal

20) Tool Life Management

21) Tool Presetter, Automatic

22) Transformer

23) Turnmill Function Including C-axis (0.0001°)

24) Turnmill Holder (Axial/ Radial)

25) Turret for VDI 60

26) U-Drill Holder

27) Wide Type Turret Disk-BMT75

28) 15” Color LCD(only FANUC)

1) Coolant System

2) Door Interlock

3) Dual Pressure (C-axis Brake)

4) Foot Switch

5) Hydraulic Chuck & Cylinder, 15” Hollow

6) Hydraulic Unit

7) Leveling Bolt & Plate

8) Lubrication System

9) Manual Guide i

10) Operation Manual & Parts List

11) Signal Lamp with 3 Colors (R, G, Y)

12) Spindle Air Curtain

13) Spindle Oil Cooling System

14) Standard Turret, 12 Station

15) Tailstock with Dead Center, MT#5- Tailstock Body Program

- Tailstock Quill Program

16) Tool Kit & Box

17) Tooling System

18) Work Light

19) 10.4” Color LCD

Optional Accessories

Accessories【Hi-TECH 700】HS-T073-R6.27-20180405

※Unit: mm(inch)

【Front】【Side】

Machine Size【Hi-TECH 700】HS-T073-R2.2-20160226

Floor Space (LxWxH) : 5,065(199.41”) x 2,282(89.94”) x 2,535(99.8”) mm(inch)

Weight : Std. - 17,350kgf , MC - 17,500kgf

Electric power (kVA) : 75

Transformer : 75kVA

Size of power cable : 38 SQ

※Unit: mm(inch)

Foundation【Hi-TECH 700】HS-T073-R4.22-20190116

Moving Range 【Hi-TECH 700/Std.】HS-T073-R4.22-20180405

※Unit: mm(inch)

OD Holder

Moving Range 【Hi-TECH 700/Std.】

※Unit: mm(inch)

ID Holder

HS-T073-R4.22-20180405

Moving Range 【Hi-TECH 700/MC】【Option】

※Unit: mm(inch)

OD Holder

HS-T073-R4.22-20180405


※Unit: mm(inch)

ID Holder

HS-T073-R4.22-20180405


※Unit: mm(inch)

Axial Turnmill Holder

HS-T073-R4.22-20180405


※Unit: mm(inch)

Radial Turnmill Holder

HS-T073-R4.22-20180405

Turret Interference Dia.【Hi-TECH 700/Std.】

※Unit: mm(inch)

HS-T073-R4.22-20180405

Turret Interference Dia.【Hi-TECH 700/MC】【Option】

※Unit: mm(inch)

HS-T073-R4.22-20180405

Tooling System 【 Hi-TECH 700/Std.】HS-T073-R1.11-20181023

Tool

mm(inch)

Part No.

mm(inch)Part name

Q’ty

eaShape

394305B( ← )BLOCK

5

394306B( ← ) 5

3943094

(39430941)

Interference Prevention

Holder1

3943093

(39430391)Face Holder 1

3943091

(39430911)ID Holder 5

Set3991101

(399120A)

5A4301(394367) Sleeve(Ø12, 1/2”) 1

5A4302(394366) Sleeve(Ø16, 5/8”) 1

5A4303(394365) Sleeve(Ø20, 3/4”) 1

5A4304(394364) Sleeve(Ø25, 1”) 1

5A4305(394363) Sleeve(Ø32, 1 1/4”) 1

5A4306(394362) Sleeve(Ø40, 1 1/2”) 1

5A4307(394361) Sleeve(Ø50, 2”) 1

3943231(394373) Socket(MT#1) 1

5A4308(394372) Socket(MT#2) 1

5A4309(394371) Socket(MT#3) 1

5A4310(394370) Socket(MT#4) 1

3943191(394369) Socket(MT#5) 1

394392

(3943921)U-Drill Holder Option

394334(3943341) U-Drill Sleeve(Ø12, 1/2”)

Option

394335(3943351) U-Drill Sleeve(Ø16, 5/8”)

11v4310(11v43101) U-Drill Sleeve(Ø20, 3/4”)

11v4311(11v43111) U-Drill Sleeve(Ø25, 1”)

11v4312(11v43121) U-Drill Sleeve(Ø32, 1 1/4”)



□ 32(□ 1.25”)

Ø 60(Ø 2.5”)

Tooling System 【 Hi-TECH 700/MC】【Option】HS-T073-R1.11-20181023

Tool

mm(inch)

Part No.

mm(inch)Part name

Q’ty

eaShape

3946005 (39460051) OD Holder 4

3946004 (39460041)Interference Prevention

Holder1

3946003 (39460031) Face Holder 1

3946001(39460011) ID Holder 3

Set

3991101

(399120A)

5A4301(394367) Sleeve(Ø12, 1/2”) 1

5A4302(394366) Sleeve(Ø16, 5/8”) 1

5A4303(394365) Sleeve(Ø20, 3/4”) 1

5A4304(394364) Sleeve(Ø25, 1”) 1

5A4305(394363) Sleeve(Ø32, 1 1/4”) 1

5A4306(394362) Sleeve(Ø40, 1 1/2”) 1

5A4307(394361) Sleeve(Ø50, 2”) 1

3943231(394373) Socket(MT#1) 1

5A4308(394372) Socket(MT#2) 1

5A4309(394371) Socket(MT#3) 1

5A4310(394370) Socket(MT#4) 1

3943191(394369) Socket(MT#5) 1

394602A(3946021S) U-Drill Holder Option

394334(3943341) U-Drill Sleeve(Ø12, 1/2”)

Option

394335(3943351) U-Drill Sleeve(Ø16, 5/8”)

11v4310(11v43101) U-Drill Sleeve(Ø20, 3/4”)





□ 32(□ 1.25”)

Ø 60(Ø 2.5”)

1) mm: 32mm

2) inch: 1 ¼”

Max. Ø 100

Radial Rotary Holder

(3900455)

Axial Rotary Holder

(3900452)

Radial Tapping Holder

(3900456)

Axial Tapping Holder

(3900453)

Axial Face Holder- mm: 3900457- inch: 3900451

Cap

(394607A)

Turnmill Holder

Tooling System 【 Hi-TECH 700/MC】【Option】

Collet Set

ER50

39456211 (39456212)

Tap Set

ER40

3591971 (3945672)

1) mm: ER50

Ø 8, 10, 12, 14, 16, 18, 20, 22, 24, 26,

28, 30, 32

2) inch: ER50

Ø1/2”, 9/16”, 5/8”, 11/16”, 3/4”, 13/16”,

7/8”, 5/16”, 1”, 1 1/8”, 1 1/4”

1) mm: ER40

M6, M8, M10, M12, M14,

M16, M18, M20, M22, M24-25

2) inch: ER40

M3/8”, M7/16”, M1/2”, M9/16”,

M5/8”, M3/4”, M7/8”, M1”

HS-T073-R1.11-20181023

α30 / 6000i

37/30kW (50/40HP)

Max 1,800 rpm

Torque Diagram 【Main Spindle】

Standard

HS-T073-R1.6-20180405

α40 / 6000i

45/37kW (60/50HP)

Max. 1,800 rpm

Torque Diagram 【Main Spindle】【Option】

Option

HS-T073-R1.6-20180405

1PH8186

42/28kW (56/37.5HP)

Max. 1,800 rpm

Torque Diagram 【SIEMENS】【Option】

Option

HS-T073-R1.6-20180405

α6 / 10,000i

7.5/5.5kW (10/7.5HP)

Max. 2,000 rpm

【BMT 85】

Torque Diagram 【Turnmil Spindle】【Option】HS-T073-R1.6-20180405

1PH8103-1DF02

9.4/5.5kW (12.6/7.5HP)

Max. 2,000 rpm

【BMT 85】

Torque Diagram 【Turnmil Spindle, SIEMENS】【Option】HS-T073-R1.6-20180405

The heavily ribbed torque tube design processed with fine grain meehanite prevents twisting and

deformation. This design ensure high rigidity with no deformation during heavy & high-speed cutting.

High rigid slant angle allows for easy loading, changing and inspection of tools. This slant angle

maintains high stability and brilliant balance

High Rigid, Stable Bed Frame HS-T073-R6.26-20180405

Chuck Size (inch) 15”(Opt.: 18”/21”/24”)

Type of Spindle Nose (ASA) A2-11

Max. Spindle speed (rpm) 1,800

Spindle Motor power (kW/HP) 37/30(50/40)

Ultra-precision(Ø180mm(7.09”)) double row of cylindrical roller bearings in the front and duplex

angular thrust bearings ensure excellent stabilities for heavy duty cutting

By adopting the powerful spindle motor 37Kw(Opt. 45Kw), Heavy duty cutting and abnormal

workpiece can be possible with superior machining

Ø 180mm(7.09”)

High performance SpindleHS-T073-R6.26-20180405

The thermal deformation of the spindle is minimized. Because generated heat is removed by

Jet Lubrication system as well as circulating jacket inside. For this reason, the accuracy of

the machining is raised and constantly stabilized.

Jet Lubrication System for Spindle【Patent pending】HS-T073-R6.26-20180405

Power is delivered to the spindle through a two speed transmission allowing

high spindle speed as well as powerful low torque.

Speed Range

• Low Speed: 0~450rpm

• High Speed: 0~1,800rpm

Programmable gear change

• Low Speed: M41

• High Speed: M42

Powerful Transmission

Gear changer

HS-T073-R6.26-20180405

Quill Dia. : Ø 150mm(Ø 5.9”)

Quill Stroke : 150mm(5.9”)

Tailstock Stroke : 1,878mm(73.93”)

Quill Taper : MT #5

The quill is activated by foot pedal or program.

The Tailstock Body is activated by Program.

Absorbed thermal deformation, ensures high

precision machining

Tailstock

Built-in Quill

HS-T073-R6.26-20180405

Max. Cutting Workpiece

Standard Cutting Diameter: Ø 387 (15.23”)

Max. Cutting Length : 1,986 (78.18”) [MC: 1,866 (73.46”)]

Ø 387mm (Ø 15.23inch)

1,986mm (78.18inch)

HS-T073-R6.26-20180405

Axis Driving Motor

X-Axis: Box Way (Turcite)

Z-Axis: Box Way (Turcite)

Type of Slider

X-Axis: 6kW(8HP), α40/3000i

Z-Axis: 6kW(8HP), α40/3000i

Rapid Speed(X/Z) : 18m/min

Double

Pretension

Ball screw

Direct Connection

Between Motor &

Ball Screw

The servo motors are connected to the ball screws without intermediate gears for quiet and

responsive slide movement with virtually no backlash.

High precision X & Z axisHS-T073-R6.26-20180405

【Standard Turret】【Turnmill Turret】

※ Number of Max. Rotating Tool available: 6 tools

The heavy duty turret maintains

exceptionally perfect precision

and extended tool life

Turret Type: Servo Motor Type

Turret Station: 12

Clamp Force: 20,000kgf (44,093lbf)

Tool Size: □ 32(1.25”) ×Ø60(2.5”)

Chip to Chip(100mm): 2.5sec

Indexing Time: 0.4sec / step

Heavy duty TurretHS-T073-R6.26-20180405

Polar Coordinate Interpolation Cylindrical Interpolation

Driven tools for Milling, Tapping and Drilling contribute

to highly intensive process with spindle indexing

(0.0001˚ ) by a Spindle motor.

Machining is one process can be achieved.

Turnmill with C-axis【Option】

Tapping

DrillingDill / tap

Size

ø32mm(ø1.26”)

M24

HS-T073-R6.26-20180405

Various Function

• Minimized coordinate setup time by easy touch sensor manipulation (less than 15sec)

• Auto calculation input of shape calibration value of tool coordinate

• Auto tool coordinate correction on work shape change

Automatic Tool Presetter

Tool Presetter【Option】HS-T073-R6.26-20180405

The large capacity coolant tank and

chip cover are separate from the

machine bed to prevent heat transfer

and easy cleaning

※ Tank capacity: 300ℓ (79gal)

Std. Pump Opt. Pump0.1 MPa 0.6/ 1.5/ 3/ 7 MPa

Coolant Equipments

└ High pressure

HS-T073-R6.26-20180405

50 ℓ

For operation of Turret, Chuck cylinder, Tailstock and Steady Rest.

Hydraulic UnitHS-T073-R6.26-20180405

12 ℓ

Automatic lubrication is provided to all guide ways and ball screws.

A low level alarm prevents the machine from restarting without lubricant.

Lubrication UnitHS-T073-R6.26-20180405

Model

ItemASR 1 ASR 2 ASR 3 ASR 3.1 ASR 3.2 ASR B 5 ASR B5.1

Min. Clamp Dia. Ø 4 Ø 8 Ø 12 Ø 20 Ø 50 Ø 50 Ø 90

Max. Clamp Dia. Ø 64 Ø 101 Ø 152 Ø 165 Ø 200 Ø 310 Ø 350

Available

Machine Model

C-240

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-700 H-700

Korea Manufacturer

Steady Rest 【Option/KHAN】HS-T073-R6.26-20180405

Model

ItemSLU 1 SLU 2 SLU 3 SLU 3.1 SLU 3.2 SLU B 5 SLU B5.1

Min. Clamp Dia. Ø 4 Ø 8 Ø 12 Ø 20 Ø 50 Ø 50 Ø 90

Max. Clamp Dia. Ø 64 Ø 101 Ø 152 Ø 165 Ø 200 Ø 310 Ø 350

Available

Machine Model

C-240

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-300/400

H-450

H-550

H-700

H-700

H-7026

H-700

H-700BB+

German Manufacturer

Steady Rest 【Option/SMW】HS-T073-R6.26-20180405

Model

ItemSLZB 50315 SLZB 90360

Min. Clamp Dia. Ø 50 Ø 90

Max. Clamp Dia. Ø 315 Ø 360

Available

Machine ModelH-700 H-700

Italian Manufacturer

Steady Rest 【Option/Morari】HS-T073-R6.26-20180405

Steady Rest Block 【Option】

Prepared accessory with Rest Base

► Hy’d Line with Valves for Open & Close of Rest Fingers

► Lubrication Line of Rest Finger Rollers

► Interlock Switch between Rest Base and Tailstock

► All necessary PLC ladder with M-code

Method of Feed

► Programmable Type

► Manual Type

HS-T073-R6.26-20180405

Operation Panel

The operator panel is mounted on the right hand side and it fixed on the

machine main cover. The layout and location of the panel is ergonomically

designed to be efficient and convenient for the operator.

10.4” Color LCD(Std.), Full Key type (Fanuc)

HS-T073-R6.26-20180405

Easy Programming【Standard】

Easy programmingBased on ISO-code program

format, complex machining

motions can be created easily by

menu form

Intuitive menu selectingMenu can be selected easily and

intuitively by soft-key with icon

Good affinity with CAD/CAMMost popular ISO-code program format

on CAD/CAM can be dealt as it is

All-in-one ScreenOnly one screen concentrated

all operations

Machine status windowMachine status such as actual

position, feed rate and load meter

are displayed always

Realistic machining

simulation3-D solid model machining

simulation is available

CAD/CAM

(Communication Programming ☞ Manual Guide i)

HS-T073-R6.26-20180405

Arbitrary speed threading will make it possible for an operator to override the spindle speed during a

threading cycle while staying in lead.

This option will also allow an operator to change the spindle speed in the program and stay in lead

without needing to use the thread repair function.

Changing spindle speed override is

prohibited in this period.

Spindle speed override can be changed.

※ This function works with the Fanuc 0i-TF and 31i-B controller.

Arbitrary Speed Threading 【Option】HS-T073-R6.26-20180405

0

0.5

1

1.5

2

2.5

3

2 4 6 8 10 12 14

30 kW

MRR : 1170 cc/min.

37 kW

Dep

th

Feed

Cutting Ability【Outer Cutting】

Depth (mm)

Feed (

mm

/rev)

Material: SM45C (Ø 300×1500)

Spindle Speed (N): 115rpm

HS-T073-R4.21-20150708

Material : SM45C

Spindle speed(N) : 177 rpm

Cutting Depth : 6 mm

Cutting Feed : 0.2 mm/rev

Cutting speed(V) : 85 m/min. 400

Ø1

56

0 2 4 6 8 10

20

60

100

80

40

Cutting Time (sec)

Spin

dle

Load

Cutting Ability【Groove Cutting】

Bite Width 8mm (70%)

Bite Width 10mm (80%)

Vibration: Good

HS-T073-R4.21-20150708

Tool : Facemill [Ø 100, t=6]

Material : SM45C

Cutting speed(V) : 120 m/min.


Ad

(mm

)

F (mm/Insert)

0.10

2

0.2 0.3 0.4 0.5 0.6 0.7 0.8

4

6

8

10

0.9

MRR 133cc/min

1.7

5.9

3.9

2.92.4

1.91.5 1.3 1.1

Cutting Ability【Facemill】

Load 100%

HS-T073-R4.21-20150708

Tool : Endmill [Ø 40, t=4]

Material : SM45C

Cutting speed(V) : 60 m/min.


Ad

(mm

)

F (mm/Insert)

0.10

2

0.2 0.3 0.4 0.5 0.6 0.7 0.8

4

6

8

10

0.9

MRR 45cc/min

1.7

5.9

3.9

2.92.4

1.91.5 1.3 1.1

Load 95%

Cutting Ability【Endmill】HS-T073-R4.21-20150708

40mm

6m

m

350

Index Grooving

• t: 4, f: 190mm/min.

• Time : 12 min.

Cutting Ability

Face Milling (Ø 100）

• t: 6, f: 190mm/min.

• Time : 12.7 min.

HS-T073-R4.21-20150708

Sample workpieceHS-T073-R1.1-20121211

Packing Dimension【Hi-TECH 700】HS-T073-R4.22-20190116

No Model ContentsDimension (mm) CBM

(m3)

Weight (kgf)

Length Width Height N/W G/W

1

Hi-TECH 700

STD Machine 5,390 2,610 3,140 44.000 17,350 18,950

2 MC Machine 5,390 2,610 3,140 44.000 17,500 19,100

3

-

T/F 1,050 916 1,110 1.068 380 450

4 C/C+T/F 5,500 1,800 1,800 18.000 1,360 1,960

Item Unit

HWACHEON Doosan

Hi-TECH 700 PUMA 500 S 700

Chuck size mm(inch) 15” 18” 15”

Max. Cutting Dia. mm(inch) Ø 680 Ø 700 Ø 700

Max. Cutting Length mm(inch) 1,986 1,575 1,727

Stroke (X/Z) mm(inch) 360/2,050 370/1,575 -

Max. speed rpm 1,800 1,500 1,500

Main spindle motor kW 37/30(50/40) 45/37(60/50) -

Controller - FANUC 0i-TF FANUC-18iTB/21iTB -

Comparison with competitorHS-T073-R5.21-20150825

Update History (1)

(1) Last Update : Jan. 16th, 2019

(2) Responsible: Marketing Team

(3) Rectification:

[1.1] Nov. 26th, 2008: Rectification of part number of Drill Socket for Tooling system

[1.2] Dec. 29th, 2008: Update of Sales point - Jet Lubrication page

[1.3] Mar, 09th, 2009: Update of dimension between floor to middle of screen (Machine Size) --> HAP Request

[1.4] Mar, 30th, 2009: Addition of cutting performance

[1.5] Apr. 09th, 2009: ① Rectification of inch value of Max. Cutting length (28.74” → 78.74”)

② Update of Accessories

[1.6] Apr. 27th, 2009: ① Upgrade of form (Design) of Machine specification

② Upgrade of form (Design) of NC specification

③ Upgrade of form (Design) of NC Instruction & Rectification of No. of Offset

[1.7] Mar. 23th, 2010: ① Upgrade of axes motors from α30/3000i(6kW) to α40/3000i(7kW)

② Rectification of NC specification from Std. to option about Play back function

③ Upgrade of axes motors of seals points

[2.8] July, 26th, 2010: Correction of NC Specification

[3.9] Aug., 10th, 2010: ① Rectification of machine name from FANUC-18iTB to FANUC 0i-TD → Machine Specification, Comparison with Competitor

② Rectification of machine name from HITECH 700 to Hi-TECH 700

→ Line-up, Machine Specification, Foundation, Tooling System, Torque Diagram, Packing Dimension, Comparison with Competitor

③ Correction → NC Instruction, Accessories, Sale point

[4.10] Aug. 17th, 2010: Correction of NC Specification

[4.11] Sep. 10th, 2010: Correction of NC Specification

[4.12] Dec. 11th, 2012: Upgrade of Sales Manual design (Form)

[4.13] Jan. 21th, 2013: Correction of Tooling System: MC Type (BMT Turret -> x)

[4.14] Feb. 4th, 2013: Correction of Max. Bar Size (117->116)

[4.15] Sep. 29th, 2013: Correction of U-Drill Sleeve Part number in Tooling System

[4.16] May, 27th, 2013: Correction of Steady Rest Maker (SMW -> Morari, Morari -> SMW)

[4.17] July, 4th, 2013: Correction of Toolling System: Correction of U-Drill sleeve inch part no.

[4.18] Aug. 20th, 2013: Correction of Toolling System: Correction of sleeve part no.

[4.19] Nov. 18th, 2013: Correction of Accessories

[4.20] Feb. 3th, 2015: ① Toolling System: Correction of Collet set Part No.

② Toolling System: Correction of Block Part No.

③ Addition of High Pressure Coolant Pump 30bar option

[4.21] Jul. 8th, 2015: ① Correction of Max. Cutting Length & Dia. (2,000 -> 1,986 / MC : 1,866, Ø 650 -> Ø 680)② Correction of Tool Interference Diagram & Moving Range③ Correction & Update of Foundation, Accessories, Sales Point and etc.

Update History (2)

[5.21] Aug. 25th, 2015 :Upgrade of Fanuc controller (0i-TD-->0i-TF),Machine Spec. / NC Spec. / NC Instruction / Comparison data

[5.22] Oct. 7th, 2015 : Correction of Sales Manual totally

[5.23] Dec. 14th, 2015 : Add Torque Diagram – SIEMENS

[5.24] Jen. 14th, 2016 : Add Torque Diagram – SIEMENS

[6.25] Feb. 26th, 2016 : Correction of Tatal Sales manual by Updating of Photo

[6.26] Oct. 26th, 2016 : Correction of Collet Part number

[6.27] Oct. 31st, 2016 : Correction of Chuck Dual Pressure System (Optional Status -> Standard Status)

[6.28] Nov. 14th, 2016 : Correction of orthography of Chuck Dual Pressure [Dual Pressure (Chuck / C-axis brake)]

[6.29] Dec. 07th, 2016 : Standard application of Signal Lamp with 3 Colors

[6.30] Mar. 23rd, 2017 : Add Siemens NC Specification and Instruction

[6.31] Apr. 03rd, 2017 : 1. Correction of C-axis Index Angle (0.001 -> 0.0001)

2. Add of Chuck Clamp/Unclamp Confirm Switch to Accessories

[6.32] Jun. 14th, 2017 : NC specification for tool presetter is applied as standard.

[6.33] Aug. 22nd, 2017 : Correction of Part No. of Tooling System

[6.34] Apr. 05th, 2018 : 1. Added 'Option' word to Moving Range , Turret Interference Dia, Tooling System and Torque Diagram

2. Modified 'bar' word to 'MPa‘

[6.35] Oct. 23rd, 2018 : Tooling System Update

[6.36] Jan. 16th, 2019 : Correction of Machine Weight & Packing Dimension

Extra-Large Horizontal Turning Center

Documents

Transcript of Extra-Large Horizontal Turning Center