ECE 1201 - staff.iium.edu.my
Transcript of ECE 1201 - staff.iium.edu.my
ECE 1201
Engineering Lab II
Taaruf
• Nor Farahidah Za’bah
• Room number : E2-2-13.12
• Phone number : 03-61964562
• Email address : [email protected]
• The lab technicians are
– Br. Ahmad Suhairi and Br. Rosley Mahadi
• Course website:
• http://staff.iium.edu.my/asuhairi/koe/
Tentative Week Experiment No. (Title) 1 Introductory class – Briefing on the organization of the course
2 Introduction to PSPICE – Tutorial 1
3 PSPICE - Tutorial 2
4 Experiment No. 1 & 2
(Diode Characteristics & Zener Diode Characteristics)
5 & 6 Experiment No. 3
(Wave Rectifier & Clipper Circuit)
7 & 8 Experiment No. 4
(BJT Characteristics & Common-Emitter Transistor Amplifier)
9 & 10 Experiment No. 5
(BJT Biasing Circuits)
11 Experiment No. 6
(MOSFET - Common Source Amplifier)
12 Experiment no. 7
(Inverting and Non-Inverting OP Amp)
Pre-lab 10 %
Quiz 15 %
Final Test 30 %
Lab Report 45 %
Assessment
Safety
• Please wear Kulliyyah jacket and covered shoes – NO SLIPPER. Otherwise, you will be asked to leave the lab.
• Power must be switched off whenever an experiment or project is being assembled, disassembled, or modified.
Tidiness
• When the experiment has been satisfactory completed and the results approved by the instructor, the students may disconnect the circuit and return the components and instruments to the locker tidily.
• Chairs are to be slid in properly.
• DO NOT WRITE anything on the table
Pre-Lab Questions and Preparation
• Please complete the pre-lab questions before each lab sessions. – It serves as guidance for you while doing your experiment
• Read the entire experiment and research any required
theory beforehand. Many times an experiment takes longer that one class period simply because a student is not well prepared.
• The experiment is performed in pairs (max=3 students per group) but the final exam is performed individually – One group = one lab report
Lab Reports
• Reports have to be handwritten for submission. – Writing should appear on one side of each sheet only.
– The students’ name & matric number, section number, lab session and the lecturer’s
– Please indicate the author of each section in your report.
• This must be followed in the middle of the sheet by: – The course code
– The experiment number
– The title of the experiment
– The date on which the student carried out the experiment.
Report format and evaluation
Tentative Week Experiment No. (Title) 1 Introductory class – Briefing on the organization of the course
2 Introduction to PSPICE – Tutorial 1
3 PSPICE - Tutorial 2
• Please download the PSPICE software and its tutorial from the website into your laptop.
• One group will need only need one laptop
Preparation for PSPICE Tutorial
Preparation for PSPICE Tutorial
• Download 16.6_OrCAD_Lite_Capture&PSpice_Products.zip from the any computer in the lab
– It is a zipped file, you have to extract the files into a designated folder
– Once you have extracted, go to Disk 1 and look for SETUP (it is an application file) to install the software.
Introduction to Lab Equipment
• Bread board and its connections
• Function Generator
– To create AC signals such as Sine-Wave, Triangular Waves etc
– The user can alter its frequency and amplitude
Example of a function generator
• Oscilloscope
– An equipment to show the obtained result.
– Has 2 channels
• One for input signal
• One for output signal
• DC power supply
– To provide DC supply to your circuit which you can measure using digital multimeter