DV-310-Kradio-hobby.org/uploads/schemes2/1002-DVD/PIONEER DV-310-S.pdf · a soldering iron. If you...

ORDER NO.

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, JapanPIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, BelgiumPIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 20082008 Printed in Japan

OPEN/CLOSE

HOMEMENU RETURN

ENTER

TOP MENU MENU

USBDVD/USB

STANDBY/ON

2 53 6 7

9 81213

DV-310-S

RRV3756

DVD PLAYER

DV-310-SDV-310-KTHIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

Model Type Power Requirement Region No. Remarks

DV-310-S WYXZT5 AC 220 V to 240V 2

DV-310-S WSXZT5 AC 220 V to 240V 5

DV-310-K WYXZT5 AC 220 V to 240V 2

DV-310-K WSXZT5 AC 220 V to 240V 5

For details, refer to "Important Check Points for good servicing".

T-ZZV MAY

2 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

SAFETY INFORMATION

This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trainedto properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.

WARNING !

THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1.A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.

LASER DIODE CHARACTERISTICS

FOR DVD : MAXIMUM OUTPUT POWER : 5 mW WAVELENGTH : 650 nmFOR CD : MAXIMUM OUTPUT POWER : 5 mW WAVELENGTH : 780 nm

Additional Laser Caution

∗ : See page 26.

1. • Laser diode is driving with Q2303,Q2305(650nm LD) and Q2302, Q2304(780nm LD)on the DVD MT PCB Assy. Therefore, when short-circuit between the emitter and collector of these transistors or the base voltage is supplied for transistors turn on, the laser oscillates. (failure mode) • In the test mode ∗ , there is the mode that the laser oscillates except for the disc judgment and playback. LD ON mode in the test mode oscillates with the laser forcibly.

2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam.

LABEL CHECK

(Printed on the Rear Panel)

Location: inside of the unit

OPEN/CLOSE

HOMEMENU

RETURN

ENTER

TOP MENU

MENU

USB

DVD/USB

STANDBY/ON

3DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

4 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

CONTENTS SAFETY INFORMATION..........................................................................................................................................................21. SERVICE PRECAUTIONS ....................................................................................................................................................5

1.1 NOTES ON SOLDERING ...............................................................................................................................................51.2 WHEN REPLACING DVD DECK ....................................................................................................................................51.3 DISC REMOVAL METHOD.............................................................................................................................................6

2. SPECIFICATIONS .................................................................................................................................................................72.1 ACCESSORIES ..............................................................................................................................................................72.2 SPECIFICATIONS...........................................................................................................................................................82.3 DISC/CONTENT FORMAT .............................................................................................................................................92.4 PANEL FACILITILES.....................................................................................................................................................11

3. BASIC ITEMS FOR SERVICE.............................................................................................................................................133.1 CHECK POINTS AFTER SERVICING..........................................................................................................................133.2 PCB LOCATIONS .........................................................................................................................................................143.3 JIGS LIST .....................................................................................................................................................................15

4. BLOCK DIAGRAM...............................................................................................................................................................164.1 OVERALL WIRING DIAGRAM......................................................................................................................................164.2 OVERALL BLOCK DIAGRAM.......................................................................................................................................184.3 DVD LOADER/MPEG BLOCK DIAGRAM.....................................................................................................................194.4 POWER BLOCK DIAGRAM..........................................................................................................................................20

5. DIAGNOSIS.........................................................................................................................................................................215.1 TROUBLE SHOOTING .................................................................................................................................................215.2 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY .............................................25

6. SERVICE MODE .................................................................................................................................................................266.1 SERVICE MODE PROCEDURE...................................................................................................................................266.2 SERVICE MODE IN ......................................................................................................................................................276.3 DISPLAY SPECIFICATION OF THE SERVICE MODE ................................................................................................286.4 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY........................................................................................296.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ........................................................................................30

7. DISASSEMBLY....................................................................................................................................................................318. EACH SETTING AND ADJUSTMENT ................................................................................................................................36

8.1 RE-WRITE FOR DVD FIRMWAVE ...............................................................................................................................369. EXPLODED VIEWS AND PARTS LIST...............................................................................................................................38

9.1 PACKING ......................................................................................................................................................................389.2 EXTERIOR SECTION...................................................................................................................................................409.3 06 DVD MECHA SECTION...........................................................................................................................................42

10. SCHEMATIC DIAGRAM ....................................................................................................................................................4410.1 DVD MT PCB ASSY(1/6) ............................................................................................................................................4410.2 DVD MT PCB ASSY(2/6) ............................................................................................................................................4610.3 DVD MT PCB ASSY(3/6) ............................................................................................................................................4810.4 DVD MT PCB ASSY(4/6) ............................................................................................................................................5010.5 DVD MT PCB ASSY(5/6) ............................................................................................................................................5210.6 DVD MT PCB ASSY(6/6) ............................................................................................................................................5410.7 OPERATION PCB ASSY ............................................................................................................................................5610.8 POWER PCB ASSY(1/2) ............................................................................................................................................5810.9 POWER PCB ASSY(2/2) ............................................................................................................................................6010.10 WAVEFORMS...........................................................................................................................................................62

11. PCB CONNECTION DIAGRAM ........................................................................................................................................6411.1 DVD MT PCB ASSY....................................................................................................................................................6511.2 OPERATION PCB ASSY ............................................................................................................................................6711.3 POWER PCB ASSY....................................................................................................................................................6811.4 LOADING MOTOR and SW ........................................................................................................................................70

12. PCB PARTS LIST ..............................................................................................................................................................71

5DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

1. SERVICE PRECAUTIONS1.1 NOTES ON SOLDERING

1.2 WHEN REPLACING DVD DECK

• For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering.

• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 °C. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 °C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron.

Do NOT use a soldering iron whose tip temperature cannot be controlled.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden).

The following lead-free solders are available as service parts:• Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia.

Before removing Pick Up PCB and DVD PCB connector, short circuit the position shown in Fig. 1 usinga soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged.

WHEN REPLACING DVD DECK

[ Removing the DVD Deck ]

[ Installing the DVD Deck ]

Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVDPCB connector.

NOTE

Fig. 1

Before your operation, please read “PREPARATION OF SERVICING” .Use the Lead Free solder.Manual soldering conditions• Soldering temperature: 320 ± 20°C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5CuWhen Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent theFlux smoke from it.

•••

•

Short circuit using asoldering iron.

Pick Up PCB

6 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

1.3 DISC REMOVAL METHOD

The laser diode used for a pickup head may be destroyed with external static electricity.Moreover, even if it is operating normally after repair, when static electricity discharge isreceived at the time of repair, the life of the product may be shortened.Please perform the following measure against static electricity, be careful of destruction of alaser diode at the time of repair.

• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat.• Soldering iron with ground wire or ceramic type is used.• A worker needs to use a ground conductive wrist strap for body.

PREPARATION OF SERVICING

If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the stepsbelow.

Set the DVD to the Stand-by Mode.Press and hold the 'STOP' key on the front panel.Simultaneously press and hold the POWER key on the front panel.The 4 digit password has now been cleared.

1.2.3.4.

PARENTAL CONTROL - RATING LEVEL4 DIGIT PASSWORD CANCELLATION

NOTE: The above procedure will reset ALL of the player's settings to the default factory state.

Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock.(Refer to Fig. 1)Manually open the Tray.

Please strongly pushing Rack Loading (White) to release the lock because the tray doesn't go outeasily.

1.

2.

Fig. 1

Rack Loading (White)

DVD Player (Bottom Side)

NOTE:

DISC REMOVAL METHOD AT NO POWER SUPPLY

7DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

2. SPECIFICATIONS2.1 ACCESSORIES

Accessories

• Remote control x1(076E0PP031:DV-310-S)(076E0PP041:DV-310-K)

• Power cable x1 (1206158802)

• Audio / Video cable(1.2m) x1 (red/white/yellow) (06CPBA2006)

• Dry cell batteries x2 (AA/R6P)

• Warranty Card

• Operating Instructions

STANDBY/ON OPEN/CLOSE

AUDIO SUBTITLE ANGLE

1 2 3

CLEAR

USB

DVD/

4 5 6

7 8 9 0

TOP MENU MENU

ENTER

RETURN

PLAY MODESURROUND ZOOM DISPLAY

PLAY

PREV PAUSE STOP NEXT

DVD

HOMEMENU

8 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

2.2 SPECIFICATIONS

GeneralPower requirements. . . . . . . AC 220V to 240V, 50Hz/60HzPower consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . .11WPower consumption (standby). . . . . . . . . . . . . . . . . . . 0.8WWeight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7kgDimensions

. . . . . . . . . . . . .420mm (W) x 49.5mm (H) x 215mm (D)Operating temperature . . . . . . . . . . . . . . . . .+5°C to +35°COperating humidity . . . . . . . . 5% to 85% (no condensation)

AV Connector(21-pin connector assignment)AV connector output . . . . . . . . . . . . . . .21-pin connectorThis connector provides the video and audio signals for connection to a compatible colour TV or monitor.

PIN no.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 2/R out3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audio 1/L out4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B out8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G out15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .R out17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video out21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND

Component video output

PPJack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA

Video output

Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA

Audio output (1 stereo pair)Output level. . . . . . . . . . . . . . . . . . . . . During audio output

200mVrms (1kHz, –20dB)Number of channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA

Digital audio characteristicsFrequency response. . . . . . . . . . . . . . . . . . . 4Hz to 44kHzS/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115dBDynamic range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88dBTotal harmonic distortion. . . . . . . . . . . . . . . . . . . .0.0065% Wow and flutter . . . . . . . . . . . . . . . . Limit of measurement

(±0.001%W. PEAK) or lower

Digital outputCoaxial digital output. . . . . . . . . . . . . . . . . . . . . . . . . . RCA

AccessoriesRemote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1AA/R6P dry cell batteries. . . . . . . . . . . . . . . . . . . . . . . . . 2Audio/video cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Power cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Warranty card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Operating instructions

The specifications and design of this product are subject to change without notice, due to improvement.

1 3 5 7 9 11 13 15 17 19 21

2 4 6 8 10 12 14 16 18 20

9DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

2.3 DISC/CONTENT FORMAT

Disc/content format playback compatibility

This player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format—see below for further compatibility information.

Please also note that recordable discs cannot be recorded using this player.

• This unit will play DVD+R/+RW discs.

• is a trademark of DVD Format/Logo Licensing

Corporation.

• is a trademark of FUJIFILM Corporation.

• Also compatible with KODAK Picture CD

This player supports the IEC’s SuperVCD standard. Compared to the VideoCD standard, SuperVCD offers superior picture quality, and allows two stereo soundtracks to be recorded. SuperVCD also supports the widescreen size.

About DualDisc playbackA DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material.

The non-DVD, audio side of the disc is not compliant with the CD audio specification and therefore may not play.

The DVD side of a DualDisc plays in this product.

For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

CD-R/-RW compatibility• Compatible formats: CD-audio, Video CD/Super VCD, ISO 9660

CD-ROM* containing MP3, WMA, MPEG-4 AAC, JPEG or DivX video/WMV files*ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible with this player.

• Multi-session playback: No

• Unfinalized disc playback: No

• File structure (may differ): Up to299 folders on a disc; up to 648 folders and files (combined) within each folder

DVD+R/+RW compatibilityOnly DVD+R/DVD+RW discs recorded in ‘Video Mode (DVD Video Mode)’ which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately.

DVD-R/-RW compatibility•Compatible formats: DVD-Video, Video Recording (VR)*

* Edit points may not play exactly as edited; screen may go momentarily blank at edited points.

•Unfinalized playback: No

•MP3/WMA/MPEG-4 AAC/JPEG or DivX video/WMV file playback on DVD-R/-RW: Yes

Compressed audio compatibility•Compatible formats: MPEG-1Audio Layer 3 (MP3), Windows

Media Audio (WMA), MPEG-4 AAC

•Sampling rates: 32kHz, 44.1kHz or 48kHz

•Bit-rates: Any (128 kbps or higher recommended)

•VBR (variable bit rate) MP3/WMA/MPEG-4 AAC playback: No

•WMA lossless encoding compatible: No

•DRM (Digital Rights Management) compatible: No (DRM-protected audio files will not play in this player

•File extensions: .mp3, .wma, .m4a (these must be used for the player to recognize MP3, WMA and MPEG-4 AAC files–do not use for other file types)

Audio CD Video CD CD-R CD-RW

DVD-Video DVD-R DVD-RW

Fujicolor CD

Super VCD

10 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

About MPEG-4 AACAdvanced Audio Coding (AAC) is at the core of the MPEG-4 AAC standard, which incorporates MPEG-2 AAC, forming the basis of the MPEG-4 audio compression technology. The file format and extension used depend on the application used to encode the AAC

file. This unit plays back AAC files encoded by iTunes® bearing the extension ‘.m4a’. DRM-protected files will not play, and files encoded with some versions of iTunes® may not play, or filenames may display incorrectly.

Apple and iTunes® are trademarks of Apple Inc., registered in the U.S. and other countries.

WMA (Windows Media™ Audio) compatibilityThis player can playback Windows Media Audio content.

WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media Player for Windows XP, Windows Media Player 9 or Windows Media Player 10 series.

•Windows Media is a trademark of Microsoft Corporation.

•This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.

About DivX videoDivX is a digital videoformat created by DivX, Inc. This player can play DiviX videos burned on CD-R/-RW/-ROM discs. Keeping the same terminology as DVD-Video, individual DivX video files are called “Titles”. When naming files/titles on a CD-R/-RW disc prior to burning, keep in mind that by default they will be played in alphabetical order.

DivX video compatibility•Official DivX Ultra Certified product.

®

•Plays all versions of DivX video (including DivX 6) with ® ®

standard playback of DivX media files. ®

•File extensions: .avi and .divx (these must be used for the player to recognize DivX video files).Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player.

JPEG file compatibility•Compatible formats: Baseline JPEG and EXIF 2.2* still image

files up to a resolution of 3072 x 2048.* File format used by digital still cameras.

•Progressive JPEG compatible: No

•File extensions: .jpg (must be used for the player to recognize JPEG files–do not use for other file types)

PC-created disc compatibilityDiscs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information.

Discs recorded in packet write mode (UDF format) are not compatible with this player.

Check the DVD-R/-RW or CD-R/-RW software disc boxes for additional compatibility information.

TM

11DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

2.4 PANEL FACILITILES

Front panel

1

2 Disc tray

STANDBY/ON

3

4 Display

5 TOP MENU

6 ENTER & cursor buttons

7 MENU

8 RETURN

9 HOME MENU

10 USB port (Type A)

11 DVD/USB

and

12

13

14

15

Press to switch the player on or into standby.

Press to pause playback. Press again to restart.

Press to start or resume playback.

Press to stop the disc (you can resume play-back by pressing (play)).

Press to open or close the disc tray.

Displays a DVD disc (or DiviX media files) menu —this varies with the disc and may be the sameas the ‘top menu’.

Selects the current menu option.

Returns to the previously displayed menu screen.

Display/exit the on-screen display.

Press to turn to USB mode and return to DVD mode.

Skips to the start of the current track, title or chapter, then to previous tracks/titles/chapters.Skips to the next track, title or chapter.

Displays the ‘top menu’ of a DVD disc—this varies with the disc.

OPEN/CLOSE

HOMEMENU RETURN

ENTER

TOP MENU MENU

USBDVD/USB

STANDBY/ON

2 53 4 6 71

9 81012 11131415

OPEN/CLOSE

12 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

Remote control

Press to switch the player on or into standby.

Press to select the audio channel or language.

Press to select a subtitle option.

Press to display the top menu of a DVD disc.

Use to navigate on-screen displays andmenus. Press ENTER to select an option orexecute a command.

Use for reverse slow motion playback, framereverse and reverse scanning.

Press to start or resume playback.

Press to display the Play Mode menu. (Youcan also get to the Play Mode menu bypressing HOME MENU and selecting PlayMode).Press to jump to the beginning of the current

Press to switch on/off virtural Surround.

Display/exit the on-screen display.

Press to open or close the disc tray.

Press to change the camera angle duringDVD multi-angle scene playback.

Press to clear a numeric entry.

Press to turn to USB mode and return to DVD mode.

Skips to the start of the current track, title orchapter, then to previous tracks/titles/chapters.

Press to pause playback; press again torestart.

Displays a DVD disc (or DiviX media files) menu —this varies with the disc and may be the sameas the ‘top menu’.

2 AUDIO

3 SUBTITLE

4 Number buttons

5 TOP MENU

6 ENTER & cursor buttons

7 HOME MENU

and

12 SURROUND

13 PLAY MODE

15 ANGLE

16 DVD/USB

17 CLEAR

18 MENU

19 RETURN

23 DISPLAY

24 ZOOM

STANDBY/ON OPEN/CLOSE

AUDIO SUBTITLE ANGLE

1 2 3

CLEAR

USB

DVD/

4 5 6

7 8 9 0

TOP MENU MENU

ENTER

RETURN

PLAY MODESURROUND ZOOM DISPLAY

PLAY

PREV PAUSE STOP NEXT

DVD

HOMEMENU

1

23

21

20

19

18

17

16

15

14

2

4

5

6

7

8

10

1213

3

9

2211

24

Press to return to a previous menu screen.

Use for forward slow motion playback, frameadvance and forward scanning.

Press to jump to the next chapter or track.

Press to display information about the discplaying.

Press to change the zoom level.

13DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

3. BASIC ITEMS FOR SERVICE3.1 CHECK POINTS AFTER SERVICING

[1] Check points after servicing (DVD player)

To keep the product quality after servicing, confirm recommended check points shown below.

See the table below for the items to be checked regarding video and audio:

[2] Cleaning

• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:

Pickup lenses Cleaning liquid : GEM1004

Cleaning paper : GED-008

Position to be cleaned Cleaning tools Position to be cleaned Cleaning tools RemarkRemark Position to be cleaned Cleaning tools Remark

No. Procedure Check points

1 Confirm the firmware version on Service Mode. The version of the firmware must be latest.Update firmware to the latest one, if it is not the latest.

The customer complain must not be reappeared.Video, audio and operations must be normal.2

Confirm whether the customer complain has been solved. If the customer complain occurs with the specific disc, use it for the operation check.

The error rates must be less than 5.0e-4.3

Confirm playback error rates at the innermost and outermost tracks by using the following disc.DVD test disc (GGV1025)

4 Play back a DVD.(Menu operation, Title/chapter search)

Audio and operations must be normal.

5Play back a DVD.(Menu operation, Title/chapter search)

Video, audio and operations must be normal.

6 Check the appearance of the product. No scratches or dirt on its appearance after receiving it for service.

Items to be checked regarding video Item to be checked regarding audio

Block noise Distortion

Horizontal noise Noise

Dot noise Volume too low

Disturbed image (video jumpiness) Volume too high

Too dark Volume fluctuating

Too bright Sound interrupted

Mottled color

14 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

3.2 PCB LOCATIONS

OPERATION PCB ASSY

POWER PCB ASSY

DVD MT PCB ASSY

DVD MECHA ASSY

Mark No. Description Part No.

LIST OF ASSEMBLIES1..DVD MT PCB ASSY A2L103A130

1..OPERATION PCB ASSY(WYXZT5) A2L103A270

1..OPERATION PCB ASSY(WSXZT5) A2L109A270

> 1..POWER PCB ASSY A2L103A240

1..DVD MECHA ASSY A2L101A650

15DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

3.3 JIGS LIST

Service Remote Control Unit GGF1381 diagnosisName Jig No. Remarks

DVD Test Disc (DVD-Video,NTSC) GGV1025 Operation CheckDVD Test Disc (DVD-Video,PAL)CD Test Disc

GGV1101STD-905

Operation CheckOperation Check

Jigs list

Lubricants and Glues list

Daifree GEM1036 (ZLX-ME413A) Refer to "9.3 DVD MECHA SECTION"

Grease GYA1001 (ZLB-PN397B) Refer to "9.3 DVD MECHA SECTION"

Grease GEM1018 Refer to "9.3 DVD MECHA SECTION"

Name Lubricants and Glues No. RemarkName Lubricants and Glues No. RemarkName Lubricants and Glues No. Remark

16 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

4. BLOCK DIAGRAM4.1 OVERALL WIRING DIAGRAM

121110987654321

121110987654321

321

CP603

321

CP604 4 3 2 1CP

602

USB

CONN

ECTO

R 4 3 2 1

CP60

5

4 3 2 1 CP40

04

11 10 9 8 7 6 5 4 3 2 1

11 10 9 8 7 6 5 4 3 2 1

21

161514131211109876543

21

161514131211109876543

WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED

Vout

B+ GND

OS65

1

123

J810121PIN CONNECTOR

1

10

11

12

13

14

15

16

17

18

19

220

213

4

5

6

7

8

9

J501AC INLET1

2

CD501

AC220V-240V_50Hz/60Hz(EU)

CAUTION:SINCE THESE PARTS MARKED

DESCRIBED IN PARTS LIST ONCRITICAL FOR SAFETY,USE ON

H1H2

E

H1H2

E

J7302CVBS/Y/U/V

1

23

4

56H E

J8001COAXIAL

12

H1H2

E

J8003AUDIO OUT

1

23

DMG099PCB130

DVD MT PCB

CD7301

32

987654

1

10

1211

32

987654

1

121110

1615

1615

1413

1413

32

987654

1

10

CD502

1211

32

987654

1

121110

GND

GND

RGB-HFS

AUDIO LGND

AUDIO R

CVBSGND

G

B

RGND

GND

RGB-HFS

AUDIO LGND

AUDIO R

CVBSGND

G

B

R

CP7301CP503

CP4003

DPG017PCB240

POWER PCB

+5V

GND

USB_

DNUS

B_DP

CD60

5

4 3 2 1

4 3 2 1

USBN

USB+

5VGN

D(US

B)

USBP

NC

NC

NC

NC

NC

P.CON+12V

P.CON+5V

FL DC-FL DC+

GND

GND

P.CON+6V

-28V

GND(M)

GND(D)

AT+3.3VAT+3.3V

P.ON-H(STBY L)

GND(USB)USB+5V

P.CON+12V

P.CON+5V

FL DC-FL DC+

GND

GND

P.CON+6V

-28V

GND(M)

GND(D)

AT+3.3VAT+3.3V

P.ON-H(STBY L)

GND(USB)USB+5V

CP502

USBN

USBP

USB+

5VGN

D(US

B)

CP40

02

DGND

FLDC

+-2

8V

V+3E IR STB

DO (F

to M

)

DI (M

to F

)CL

K

DGND

FLDC

-

POWERSW2GND

321

321

10 3 29 8 7 6 5 4 1CD

601

3 29 8 7 6 5 4 111 1011

TM101COMMAND TRANSMITTER

POWERSW2GND CP

601

DGND

FLDC

+-2

8VFL

DC-

V+3E IR STB

DO (F

to M

)

DI (M

to F

)CL

K

DGND

PCB271DEG150

OPERATION2 PCB OPERATION PCBPCB270DEG149

DVD MT PCB ASSY(1/6 - 6/6)(A2L103A130)

OPERATIONPCB ASSY(WYXZT5 : A2L103A270)(WSXZT5 : A2L109A270)

POWER PCB ASSY(1/2,2/2)(A2L103A240)

17DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

5

4

3

2

1

CP2302

6

5

4

3

2

1

CP2303

24

23

22

21

20

19

2

1

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

CP2301

VRCOM

TRKG DRV

TRKG RTN

FOCS RTN

FOCS DRV

VCC

D

B

VR780(CD)

VRF(RF_OUT)

SW1(DVD/CD)

C

E

VSF

GND

A

VR650(DVD)

GND

GND

LD_DVD(650)

LD_CD(780)

PD/GND

NC

SW(GND)

LIMIT SW

SLD-

SLD+

SPD-

SPD+

LOAD+

LOAD-

GND

OPEN

CLOSE

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

24

23

22

21

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

6

5

4

3

2

1 6

5

4

3

2

1

B

A

VRCOM

VR780(CD)

VRF(RF_OUT)

SW1(DVD/CD)

C

VR650(DVD)

GND

LD_DVD(650)

LD_CD(780)

PD/GND

TRKG DRV

TRKG RTN

FOCS RTN

FOCS DRV

VCC

D

E

VS

F

GND

GND

NC

DM-4PBDRIVEDVD

OPTICAL PICK-UP

DED021PCB610

CD2302

BCZ3B05M2603M

5

4

3

2

1

SW-2(CLOSE)

GND(SW)

SW-1(OPEN)

LOADING MOTOR(-)

LOADING MOTOR(-)

2H051602

SSS-28-5SW1

BCZ3B05

JCV9B12M2601

M2602

ESE22MH22SW2

M

M

2H061605CD2301

DED020PCB640

SPINDLE MOTOR(+)

SPINDLE MOTOR(-)

FEED MOTOR(-)

GND(SW)

FEED MOTOR(+)

PICK UO INNER LIMIT SWITCH

6

5

4

3

2

1

DVD MECHA ASSY(A2L101A650)

(SW PCB)

(LOADING MOTOR PCB)

2 12 1

E THESE PARTS MARKED BY

CRIBED IN PARTS LIST ONLYICAL FOR SAFETY,USE ONES

ARE DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE

ATTENTION:LES PIECES REPAREES PAR UN ETANT

H1H2

E

H1H2

E

J7302CVBS/Y/U/V

1

23

4

56H1

3OUT

1

2

CP40

02

DI (M

to F

)CL

K2 1

CD60

1

2 1CP

601

DI (M

to F

)CL

K

ASSY

18 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

4.2 OVERALL BLOCK DIAGRAM

P.C

ON

+12

V

AC

220~

240V

FLD

C+

/-

X40

0127

MH

z

-28V

AT+

12V

for

mut

e

AT+

3.3V

P.C

ON

+6V

P.C

ON

+5V

PO

WE

RS

UP

PLY

DV

D

LOA

DE

R(D

M4)

MO

TOR

DR

IVE

RIC

2301

AM

5766

FIP

DR

IVE

R IC

IC

651

PT

6315

AU

DIO

AM

P IC

IC80

03R

C45

80ID

R

FIP

HN

V-0

8SS

84

KE

Y

SE

RV

O

RF

SE

RV

O

IR

FP,

ST

B

AS

PD

IF

RESET

AU

DIO

_L,

AU

DIO

_R

AM

P_A

UD

IO_L

/R

LD_D

VD

,LD

_CD

IR10

8MH

zT

V E

ncod

er

MP

EG

-1/2

/JP

EG

VID

EO

DE

CO

RD

ER

R

CO

AX

IAL

RF

COL

OV

ER

AL

L B

LO

CK

DIA

GR

AM

IR R

EC

EIV

ER

(O

S65

1)K

SM

-200

1TC

2P

16M

bit F

LAS

HIC

4004

AT26

DF

-161

-SU

64M

bit(

4M*1

6) 1

43M

Hz

SD

RA

MIC

4005

M12

L641

64A

-7T

G

XA

MU

TE

MP

EG

/MIC

ON

IC40

01M

T13

89F

E/L

-LA

UD

IO C

OD

EC

/IN

TE

RN

AL

DA

C

+1.

8V

SF

LAS

H_C

SS

FLA

SH

_CK

SF

LAS

H_D

OS

FLS

H_D

I

MA

0~M

A11

, D

Q0~

DQ

15

RE

SE

T IC

IC40

03R

3112

N29

1A-

TR

-FA

VID

EO

DR

IVE

R 6

CH

ICIC

7301

LA73

054-

TLM

-E

4CH

VID

EO

DA

C

VUY4C

H B

US

SW

ICIC

7302

SN

74C

BT

3257

PW

R

21P

IN

RG

B O

UT

CV

BS

19DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

4.3 DVD LOADER/MPEG BLOCK DIAGRAM

DV

D L

OA

DE

R/M

PE

G B

LO

CK

DIA

GR

AM

DV

DLo

ader

(DM

-4)

MP

EG

/MIC

ON

ICIC

4001

MT

1389

FE

/L-L

X40

0127

MH

z

IOA

, V20

C

RF,

A, B

, C, D

, E, F

, MD

I1

LD_D

VD

, LD

_CD

Q23

02~

2305

LD D

RIV

ELD

O1,

LD

O2

MO

TOR

DR

IVE

R IC

IC23

01A

M57

66

DM

SO

, FM

SO

, T

RO

PE

N, T

RC

LOS

E,

TR

SO

, FM

SO

, S

TB

Y, V

1P4

T+

/-, F

+/-

,LO

AD

+/-

, M

OT

_SLE

D+

/-,

MO

T_S

PD

L+/-

OP

U

SP

IND

LE/

ST

EP

ING

/S

LED

MO

TOR

LIM

IT/T

RO

UT,

OP

O, O

P+

/-

AU

DIO

AM

P IC

IC80

03R

C45

80ID

R

A D

SF

LAS

H_C

S, S

FLA

SH

_DO

SF

LAS

H_C

K, S

FLA

SH

_D1

32R L

AU

DIO

JA

CK

L/R

J800

3A

UD

IO R

AU

DIO

L

AU

DIO

L, R F

A...

....A

T+

3.3V

B...

....+

1.8V

C...

....P

.CO

N+

5VD

......

.P.C

ON

+6V

E...

....A

T+

12V

F....

...P.

CO

N+

12V

G...

....-

28V

H...

....V

+5H

RE

SE

T IC

IC40

03R

3112

N29

1A-T

R-F

AA

RESET

AS

PD

IF2C

OA

XIA

L JA

CK

J800

1

VID

EO

DR

IVE

R 6

CH

ICIC

7301

LA73

054-

TLM

-E

TX

D/L

E, I

/XP,

R

/CR

, B/C

B, G

/Y, C

/VC

A, B

GR

1~G

R8,

P1~

P16

FP

_DI,

FP

_DO

, F

P_S

CK

, ST

B

35Y U

CV

BS

/Y/U

/VJ7

302

2V

FIP

(V

651)

HN

V-0

8SS

84

G19C

VB

S

21P

IN C

ON

NE

CTO

RJ8

101

1115R

OU

T

G O

UT

167B

OU

T

3L

4CH

BU

S S

W IC

IC73

02S

N74

CB

T32

57P

WR

C

RX

D/S

Q, V

SE

L1

VS

EL1

6C

VB

S

CR OUT

Y2 OUT

CB OUT

1R

8

VS

EL1

RX

D/S

Q

21 P

IN C

TL

BLA

NK

ING

_OU

T

Q81

04, Q

8105

DV

D_R

GB

_H_O

UT

MA

0~M

A11

, DQ

0~D

Q15

,D

QM

0, D

QM

1, D

BA

0, D

BA

1,

SD

CLK

, DW

E#,

D

RA

S#,

DC

AS

#

16M

bit F

LAS

HIC

4004

AT26

DF

161-

SU

A64

Mbi

t SD

RA

MIC

4005

M12

L641

64A

-7T

G

FIP

DR

IVE

R IC

IC65

1P

T63

15

A

US

BN

HIG

H S

IDE

SW

IC40

07R

5523

N00

1B-T

R-F

US

B_F

LAG

US

B_P

_ON

-L

43

CP

4004 U

SB

P

Q81

01, Q

8102

21 P

IN C

TL

IRIR

RE

CE

IVE

R (

OS

651)

KS

M-2

001T

C2P

IR A

20 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

4.4 POWER BLOCK DIAGRAM

SW

ITC

HIN

GT

RA

NS

T50

1

P.C

ON

SW

PO

WE

R B

LO

CK

DIA

GR

AM

Q50

5

AC

IN

P.C

ON

+5V

AT+

3.3V

FL

DC

-

-28V

AT+

12V

for

mut

e

P.C

ON

+6V

P.C

ON

+12

V

P.O

N-H

FL

DC

+

Q51

5

P.C

ON

+5V

RE

GQ51

0

P.C

ON

+12

V S

W

Q50

4

FL+

P.C

ON

SW

Q50

2

-28V

P.C

ON

SW

VO

LTA

GE

CT

LIC

501

KIA

431A

-AT

PH

OTO

CO

UP

LER

IC50

4P

S25

61A

L1-1

-V(W

)

PO

WE

R C

TL

IC50

2S

TR

-A61

59M

6V

RE

G

(DV

D M

OTO

R)

IC50

3P

Q07

0XF

01S

ZH

RE

G+

1.8V

IC40

06LD

1117

AL-

AD

J-A

A3-

A-R

+1.

8V

21DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

5. DIAGNOSIS5.1 TROUBLE SHOOTING

POWER DOES NOT TURN ON

Is the voltage at pin 8 and pin 9 of CP502 about 3.3V

and at pin 5 of CP502 about 5V?

No

Yes

NoIs there waveform atX4001 about 3.0Vp-p ?

Check X4001, IC4001 and

peripheral circuit.

Yes

Write DVD FIRMWARE DATA.

Check AT+3.3V line of POWER BLOCK.

Check Q515 and peripheral circuit.

No

Yes

No

DECK DOES NOT ACCEPT

OPEN/CLOSE

Check P.CON 6V line of

POWER BLOCK.

YesIs the lose connection

at CD2302 to DECK ?

Check CD2302

connection to DECK.

Change DVD LOADER.

Is the voltage at pin 8 and 19 of IC2301

about DC6V ?

22 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

DOES NOT LIGHT ON DISPLAY

Yes

Is the voltage at pin 13 and pin 43 of IC651

about 3V ?

Check AT+3.3V line of

POWER BLOCK.

No

Replace V651 or IC651.

NO PLAYBACK PICTURE OF AV

JACK

Is there video signal at pin 33

of IC7301 ?

Change IC7301.

No

Yes

No

Yes

Check J7302 and peripheral

circuit.

Is there a signal at pin 99 of

IC4001 ?

Check IC4001 and

peripheral circuit.

23DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

NO DIGITAL AUDIO ON

PLAYBACK OF COAXIAL JACK

Is there waveform at pin 2 of J8001

about 0.5Vp-p?

Check connection at RCA

Cable.

Yes

Yes

No

No

Change IC4001.

Is there waveform at pin 93 of IC4001

about 3.3Vp-p ?

Check Q8005 and

peripheral circuit.

NO ANALOG AUDIO ON

PLAYBACK

Is there AUDIO signal at pins 1 and 7

of IC8003 ?

Yes

Is there AUDIO signal at

C8051 and C8053 ?

No

Check J8003 and peripheral

circuit.

Yes

No

Check AT pins 116 and 118of IC4001

Change IC8003.

24 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

Symptoms That May Occur When Any Of The Following ICs Is In FailureIC Symptoms

16M Flash ROM(DVD MT PCB Assy : IC4004)

The power cannot be turned on.Downloading of the firmware cannot be performed.

DVD IC(DVD MT PCB Assy : IC4001)

Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be generated, because the DVD processing is performed by a single chip.

64M SDRAM(DVD MT PCB Assy : IC4005)

No power.Block noise is generated during playback.

25DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

5.2 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY

SIDE A

1 33

6597

DMG099A

X4001

J7302

Q8014

Q8019

Q8020

Q8021

Q8005

R8057

R8069

R8066

R8061 R8049

R8048R8063

R8067

R8056

R8073

R8082

R8074

R8077

R8081R

8078

R8080

R8079

R8083R8085

R8037

R8084

R8039

R8040

R8038

R8035

R8036

C8066

C8073

C8070

W840

C8042

C8056

C8057

C8058

C8067

C8069

C8072

C8077

C8078

J8001

CP7301

C7316

C7317

C7318

C7319

R7319

R7320

R7321

B7304

B7305

B4002

B8004C8036 R

7302

IC4003

IC7301 R4059

R4060

R4061

R4062

C7311

R7307

C7305

C7306

C7307C7308

D7306D7305

R7301

IC8003

J8003

R4035C7303

C8051

C8053Q8018

Q8013

C7309

C7310

R7305

D7312

D7310

D7311

C8038

L7301

Q4001

C7315

IC7302

Q7302

IC4001

R2316

W805

W806

C2307

C2312

C2311

R2310W802R

2313R

2312

R2327

R2318

R2317

R2325

C2306

IC2301

R4011

C4116

C4112

IC4006

C4100

C4099C4098

C4096

C4095

B4001

R4013

C2301

CP2302

C2321

C2320

R4012

R2309

R2306R2307

R2328

R2319

Q2303

Q2304

Q2301 Q2305

Q2302

C4052

IC4005

R4066

C4049

NR

4002

R4027

C4050

CP2303

CP4003

IC4009

C4137

C4141

R4063

R4073

R4072

C4091

C4104

IC4004

R4040

R4044

W810

R4053R4054

C4078

R4033

B4008

C4029 C4002

R4039

W808

R4024 R4025

C4090

C4089

R4014

R4015 R4016

B4007

W829

R4018

R4019

C4006

R4031

C4039C

4044

L4001

C4142

C4134

W844

W809D4003

W832W839

C4080

CP2301

W826

R4008

C4010

C2303

W816

W817

C4072C4012

NR2301

R4074

C2304

C4047

C4046

C2302

R2344

C2323

C8059

R7308

R7306

C7312

R8059

R8060

C7304

C7313

C4056

R8076

R8051

R8014

C2322

R2342

C4086

R4022C4011

C4062

C4101

C4102

C4005

C4007

C4140

C4077

R4002

C2305

R2311

R4017

R2308

C4088

C4048

C4051

R4046

CP

4002

C4132

CP

4004

Q7301

D4002

R4045

R2326

R7316

R7315

R7318

R7317

Q7305B7301

R4058

W820

R4075

R2316

W805

W806

C2307

C2312

C2311

R2310W802R

2313R

2312

R2327

R2318

R2317

R2325

C2306

IC2301

C

C4095

C2301

C2321

C2320

R2309

R2306R2307

R232

R2319

Q2303

Q2304

Q2301 Q2305

Q2302

CP2303

C4090

C4089 R4015 R4016

R4031

W832W839

CP2301

NR2301

C2304

C2302

C4056

C4101

C4102

C4007C2305

R2311

R4017

R2308

R2326

Case when this diagnosis is required : When playback of any disc, including a test disc (DVD: GGV1025, CD: STD-905), cannot be performed

How to diagnoseIn the case mentioned above, degradation of the laser diodes (LDs) mounted on the PICKUP Assy is suspected.Measure the voltage between the two ends of one of the resistors mentioned below.

Measure the voltage between the two ends of NR2301 on the DVD MT PCB Assy. If the voltage is 0.17 V or higher, the 650-nm LD is degraded.

No playback of a DVD :

Measure the voltage between the two ends of NR2301 on the DVD MT PCB Assy. If the voltage is 0.20 V or higher, the 780-nm LD is degraded.

No playback of a CD :

If the measurements show degradation of an LD, replace the PICKUP Assy.

DVD MT PCB ASSY

26 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

6. SERVICE MODE6.1 SERVICE MODE PROCEDURE

POWER ON

DSC -

GGF1381Service moderemote controlunit

GGF1381Service moderemote controlunit

<TRAY OPEN> <TRAY CLOSE>

OPEN/CLOSE(Player)

OPEN/CLOSE

Press the play key ( ) of the normal remote control unit.

(Player)

An address is displayed

OR

ESC

<PLAY>ESC TEST

CHECKDVD, CD

DVD disc

POWER

ON

OFF

POWER

DISC SET

Notes:• After going into service mode, if you play back the disc, "DISC-NON" is displayed.• The video signal and the audio signal are outputted during the servicemode.• The SKIP key and the SCAN key are effective during the service mode.

SERVICE MODE: PLAY

SERVICE MODE: OFF

27DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

6.2 SERVICE MODE IN

Service Mode Functional Specification1 Service mode entry In the power ON state, press the [ESC] (A8-5F) key and [TEST / RANDOM] (A8-5E) key in order of the Service mode remote control unit. • Light the all FL and LEDs. • OSD displays test mode.

Note: * When pressing the keys of something, the FL displays "NO DISC" and the LED lighting disappears.

2 Release the Service mode • Turn off the power. • Press the [ESC] (A8-5F) key of the remote control unit.

3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). CD : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n).

28 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

6.3 DISPLAY SPECIFICATION OF THE SERVICE MODE

Character in bold : Item name: Information display

1

56

1011

89

3

2

12

15

13

14

1 Address indication The address being traced is displayed in number. (as for the DVD, indication of decimal number is possible.) DVD : ID indication (hexadecimal number, 8 digits) [∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗] CD : ID indication [∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]

2 Code indication of remote control unit [R − ∗ ∗ ∗ ∗] In case of double code, display a 2nd code.

3 Main unit keycode indication [K − ∗ ∗]

5 Tracking status [TRKG − ∗ ∗ ∗] Tracking on : [ON] Tracking off : [OFF]

6 Spindle status [SPDL − ∗ ∗ ∗] [OFF], [CLV]

7 Mechanism (loading) position value [M − ∗ ∗] Unknown : [01] or [41] Open state : [04] Close state : [08] During opening : [12] During closing : [22]

8 Slider position [S − ∗ ∗ ∗ ∗] In Side Switch ON : [01] In Side Switch OFF : [00]

9 Output video system [V − ∗ ∗ ∗ ∗] NTSC system : [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK − ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] RGB : [02]

a Disc sensing [DSC − ∗ ∗ ∗] The type of discs loaded is displayed. [DVD], [CD ], [VCD], [ ]

b Jitter value [J − ∗ ∗ ∗ ∗] Note:Don't use it.

c Version of the FL controller [FL: ∗ ∗ ∗ ∗]

d Region setting of the player [REG: ∗] Setting value : [1] to [6]

e Destination setting of the FL controller [MDL: ∗ ∗ ∗ ∗ / ∗ ∗ ∗] Four characters in the front represent code 01. Three characters in the back represent the destination code. J: /J, K: /KU, /KC, /KU/KC, R: /RL/RD, RAM : /RAM, LB: /LB, WY: /WY

f Version of the flash ROM [VERSION: ∗∗∗∗∗∗∗∗]

7

29DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

6.4 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY

• Service mode indication (ESC + CHP/TIM keys)ID AddressThe error rate is always displayed in exponential notation, e.g., ∗.∗ ∗ e - ∗, for both DVDs and CDs.EDC/ID/AV 1 error history (ID Address, EDC/ID Error, last eight errors)

• Calculation of the average error rate (ESC + "5" [Service mode remote control unit] keys)The average of the last eight error rates is calculated and indicated in exponential notation. After the calculation is completed, "OK" or "NG" is displayed. If "NG" is displayed, the disc tray will open (for both DVDs and CDs)For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less

• Indication of model information (ESC + CHAP keys)The items from 12 to 15 of the SERVICE MODE Indications are displayed. However, in the indications, S in the standard test mode is changed to CHIP VERSION, and M is changed to FL VERSION.

• Region confirmation mode (ESC + A.MON [Service mode remote control unit] + "1"-"8" [Service mode remote control unit] keys)After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens.

Command Contents ConditionsRemote Control

Key NameRemote

ControlCodeMemory clear and region / revision indication CLEAR (∗1) A8-45

Average value measurement of DVD error rate 5 (∗1) A8-05

CD error rate measurement 5 (∗1) A8-05

Scart terminal output : VIDEO

WY, models equipped with Scart terminal

AUDIO AF-BE

Scart terminal output : S-VIDEO SUBTITLE AF-36

Scart terminal output : RGB ANGLE AF-B5

Progressive OFFOnly for progressive models

R_SKIP A3-9D

Progressive ON F_SKIP A3-9C

ZOOM ON (X2 -> X4 -> x1) ZOOM AF-37

Service mode indication (error rate indication, etc.) CHP/TIM (∗1) A8-13

Model information indication CHAP (∗1) A8-40

Title search Input mode IN Title No. input Search execution

SIDE A (∗1)Numbers (∗1)

PLAY (∗1)

A8-4DA8-00 to A8-09

A8-17

Region confimation mode A.MON (∗1)Numbers (∗1)

A8-1EA8-01 to A8-08

Only during normal playback, the following shortcut keys can be assigned by pressing a required key after pressing the ESC key of the remote control unit. To quit, press the ESC key

∗1 : Service mode remote control unit

30 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

6.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE Display during Service Mode To enter Service Mode, press the CHP/TIM key while holding the ESC key pressed. To quit, press the ESC key.

Service mode display 1 ID Address 2 Error rate (always displayed), in exponential notation ERROR RATE : ∗ ∗ ∗ ∗ ∗ ∗ ∗ ( ∗ ∗ ∗ ∗ )

• Calculation of the average error rate For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less

3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors)

Note: ∗ Error of AV1 is not supported in this player.

Number of error

Indication plan contents

Character in bold : Item name: Information display

12

3

ex) For DVDs

• Step 1

e-

e -6 : OK e -5 : OK e -4 : Refer to Step 2 e -3 : NG e -2 : NG

• Step 2

e -4

3.0e -4 : OK4.0e -4 : OK5.0e -4 : OK6.0e -4 : NG7.0e -4 : NG

31DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

7. DISASSEMBLY1.

1-1:

REMOVAL OF MECHANICAL PARTSAND P.C. BOARDS

Remove the 5 screws (1).Remove the Top Cabinet in the direction of arrow (A).Disconnect the following connectors: (CP4002 andCP4004).Unlock the 4 supports (2).Remove the Front Cabinet in the direction of arrow (B).Remove the 11 screws (3).Remove the Operation PCB in the direction of arrow (C).

TOP CABINET/FRONT CABINET AND OPERATION(Refer to Fig. 1-1)

1.2.3.

4.5.6.7.

1.

2.

3.4.

Short circuit the position shown in Fig. 1-3 using asoldering iron. If you remove the DVD Deck with nosoldering, the Laser may be damaged.Disconnect the following connectors:(CP2301, CP2302 and CP2303).Remove the 4 screws (1).Remove the DVD Deck in the direction of arrow.

1-3: DVD DECK (Refer to Fig. 1-3)

Fig. 1-3

DVD Deck

Short circuit using asoldering iron.

Pick Up PCB

(1)

(1)

(1)

(1)

NOTE

Before your operation, please read ìPREPARATION OFSERVICINGî.Use the Lead Free solder.Manual soldering conditions• Soldering temperature: 320 ± 20oC• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5CuWhen Soldering/Removing of solder, use the drawingequipment over the Pick Up Unit to keep the Flux smokeaway from it.When installing the DVD Deck, remove all the solderingon the short circuit position after the connection of Pick UpPCB and DVD MT PCB connector.

1.

2.3.

4.

5.

1-4: DVD MT PCB (Refer to Fig. 1-4)

1.2.3.

Remove the 3 screws (1).Remove the 4 screws (2).Remove the DVD MT PCB in the direction of arrow.

Fig. 1-4

DVD MT PCB

(1)(1)

(2)

(2)(2)

(2)

(1)

Fig. 1-1

(B)

(A)

Top Cabinet

Front Cabinet

(C)

Operation PCB

Operation PCB

(C)

(1)

(1) (1)

(1)

(1)

(2)(2)

(2)

(2) (3)

(3)

(3)

(3)(3)

1-2: POWER PCB (Refer to Fig. 1-2)

1.

2.3.4.

Disconnect the following connectors:(CP502 and CP503).Remove the 2 screws (1).Remove the 3 screws (2).Remove the Power PCB in the direction of arrow.

Fig. 1-2

Power PCB(2)

(1)

(2) (2)

(1)

(3)(3)

32 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

2. REMOVAL OF DVD DECK PARTS

2-1: TRAY (Refer to Fig. 2-1-A)

METHOD AT NO POWER SUPPLY)

Tray.

1. Set the Tray opened. (Refer to the DISC REMOVAL

2. Unlock the 2 supports � and draw it while sagging the

Fig. 2-1-A

Tray

Push to Sag

Push to Sag

Loader Ass'y

�

NOTE

1. In case of the Tray installation, install them as the circledsection of Fig. 2-1-B so that the each markers are met.

2-2: TRAVERSE ASS'Y (Refer to Fig. 2-2-A)

1. Remove the screw �.2. Unlock the 2 supports �.3. Remove the Insulator (R) from the Loader Sub Ass'y.4. Remove the Traverse Ass'y.

Fig. 2-2-A

Tray

Loader Ass'y

Fig. 2-1-B

Insulator (R)

NOTE

1. Disassemble only the DVD DECK PARTS parts listedhere. Minute adjustments are needed if the disassemblyis done. If the repair is needed except listed parts,replace the DVD MECHA ASS'Y.

NOTE

1. In case of the Traverse Ass'y, install it from (1) to (4) in

2. In case of the Traverse Ass'y installation, hook the wireorder. (Refer to Fig. 2-2-B)

on the Loader Ass'y as shown Fig. 2-2-C.

�

Traverse Ass'y

Loader Sub Ass'y

Fig. 2-2-BCheck Lock

Traverse Ass'y

Rack Loading

Loader Ass'y (Bottom Side)

Holder Traverse

Fig. 2-2-C

Loader Ass'y

Check Hook

Loading Belt

Loading Sub Ass'y

Gear Pulley

�

2-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT(Refer to Fig. 2-3-A)

1. Remove the Loading Belt.2. Remove the screw �.3. Remove the Loading Motor PCB Ass'y.4. Remove the 2 screws �.5. Remove the Loading Motor.6. Remove the Gear Pulley.

Fig. 2-3-A

Loading Motor PCB Ass’y

• Screw Torque: 2.0±0.3kgf•cm

• Screw Torque: 2.5±0.3kgf•cm (Screw �)• Screw Torque: 1.0±0.3kgf•cm (Screw �)

��

��

�

�

(1)(2)

(3) (3)

(3)(3)

(4) (4)

33DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

BROWN (1)

WHITE (2)

NOTE

1. In case of the Pulley Motor installation, check if the value

2. When installing the wire of the Loading Motor PCB Ass'y,

3. When installing the Loading Motor PCB Ass'y, install it

4. In case of the Loading Motor PCB Ass'y installation, hook

of the Fig. 2-3-B is correct.

install it correctly as Fig. 2-3-C.Manual soldering conditions• Soldering temperature: 320 ± 20°C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5Cu

correctly as Fig. 2-3-D.

the wire on the Loader Sub Ass'y as shown Fig. 2-3-E.

Fig. 2-3-B

7.0 0.1mm

Safety surface for pressingof the insert.

Loading Motor

Pulley Motor

Check HookLoading Motor PCB Ass’y

Loading Motor PCB Ass’yFig. 2-3-C

Fig. 2-3-E

Check Hook

Fig. 2-3-D

Rack Loading

BA

The Lever should be positionbetween A and B.

Check Hook

Rack Loading

1

Loader Sub Ass’y

Gear Main

2-4: RACK LOADING/MAIN GEAR/PULLEY GEAR(Refer to Fig. 2-4-A)

1. Unlock the support 2 and remove the Gear Pulley.2. Remove the Gear Main.3. Press down the catcher 1 and slide the Rack Loading.

Gear Pulley

2

Fig. 2-4-A

NOTE

1. In case of the Rack Loading installation, hook the Rack

2. When installing the Gear Main, take care the direction ofLoading on the Loader Sub Ass'y as shown Fig. 2-4-B.

up or down as shown Fig. 2-4-C.

Fig. 2-4-B

Rack Loading

Check Hook

Fig. 2-4-C

Main Gear

Up Side

Down Side

2-5: CLAMPER ASS'Y (Refer to Fig. 2-5-A)

clockwise, then unlock the 3 supports 1.1. Press the Clamper and rotate the Plate Clamper

2. Remove the Plate Clamper, Magnet Clamper and Clamper.

Plate Clamper

Magnet Clamper

Fig. 2-5-A

Main Frame

Clamper1

11

Loader Sub Ass'y (Bottom Side)

34 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

Holder Traverse

Insulator (F)

Traverse Ass'y

Insulator (F)

Insulator (R)

NOTE

1. In case of the Clamper Ass'y installation, install correctlyas Fig. 2-5-B.

Fig. 2-5-B

Plate Clamper

Clamper

2-6: HOLDER TRAVERSE/INSULATOR (F)/INSULATOR

1. Remove the Holder Traverse.2. Remove the 2 Insulator (F).3. Remove the Insulator (R).

Fig. 2-6-A

(R) (Refer to Fig. 2-6-A)

NOTE

1. In case of the Insulator (F) installation, install correctly as Fig. 2-6-B.

Fig. 2-6-B

Traverse Holder

Insulator (F)

2-7: SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/ RACK FEED ASS'Y/FEED MOTOR (Refer to Fig. 2-7-A)

1. Unlock the support 1.2. Remove the Gear Middle.3. Remove the screw 2.4. Remove the Rack Feed Ass'y.5. Remove the screw 3.6. Remove the Switch PCB Ass'y.7. Remove the screw 4.8. Remove the Gear Feed.9. Remove the 2 screws 5.10. Remove the Feed Motor.11. Remove the Gear Motor.

3

Gear Middle

Gear Motor

Feed Motor

• Screw Torque: 1.3 ± 0.3kgf•cm (Screw 2)• Screw Torque: 3.0 ± 0.3kgf•cm (Screw 3)• Screw Torque: 1.0 ± 0.3kgf•cm (Screw 4, 5)

Switch PCB Ass'y

2

4

Rack Feed Ass'y

Gear Feed

5

Fig. 2-7-A

Traverse Ass'y51

NOTE

1. When installing the Rack Feed Ass'y, push both ends to

2. In case of the Gear Motor installation, check if the value

3. When installing the wire of the Switch PCB Ass'y, install

4. After the assembly of the Traverse Ass'y, hook the wire

align the teeth as shown Fig. 2-7-B. Then install it.

of the Fig. 2-7-C is correct.

it correctly as Fig. 2-7-D.Manual soldering conditions• Soldering temperature: 320 ± 20°C• Soldering time: Within 3 seconds• Soldering combination: Sn-3.0Ag-0.5Cu

on the Traverse Ass'y as shown Fig. 2-7-E.

[OK] [NG]

Fig. 2-7-B

Rack Feed Ass'y

PushPush

Fig. 2-7-C

8.0 ± 0.2mm

Safety surface for pressingof the insert.

Feed Motor

Gear Motor

Check Lock

Pickup lenesesGEM1004GED-008

35DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

Traverse Ass'y

Check Hook

Check Hook

Check Hook

Fig. 2-7-E• Loosen the wire in the direction of the arrow.

Check Hook

~ FEED MOTOR ~

WHITE (4)

BROWN (3)

~ SPINDLE MOTOR ~

YELLOW (2)

GREEN (1)

Fig. 2-7-D

Switch PCB Ass'y

• Install wire from (1) to (4) in order.

[ 24 pin FFC ]

shown from Fig. 2-8.

2-8: FFC WIRE HANDLING

1. When installing the FFC, fold it correctly and install it as

positions for the FFC.1. Do not make the folding lines except the specified

NOTE

Fig. 2-8

Printing Surface Fold

79 1 mm

Reinforcement Plate

To Pick Up PCB

36 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

8. EACH SETTING AND ADJUSTMENT8.1 RE-WRITE FOR DVD FIRMWAVE1. PurposeAfter replacing the DVD MT PCB Assy, be sure to update the firmware to the latest version. The firmware of the Assy for service may not be the latest.

3. Procedures for updating the firmwareHow to update:1 Turn on the main unit and open the disc tray.2 Place the disc for updating in the disc tray and close the tray.3 Press the PLAY button.

4 Updating of the firmware is completed.

2. Procedures for creating the disc for updatingNecessary tools:1 PC with a CD-R/CD-RW drive2 Blank CD-R or CD-RW3 Firmware file (∗∗∗∗∗.BIN)

How to create:1 Start up the program for writing to CD.2 Load a blank disc in the CD-R/CD-RW drive.3 Enter "PIONEER" as the volume label.4 Select the .BIN file.5 Write the latest version of the firmware in ISO 9660 format.

While the screen shown at left is being displayed, updating is in progress.DO NOT TURN OFF THE POWER DURING UPDATING.

When the screen with the Pioneer logo is displayed, updating is completed.The time required for updating is about 2 minutes.

37DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

4. How to confirm the version of the firmwarePress the ESC then the CHAP key on the remote control unit for servicing. The version of the firmware is labeled ROM NUMBER. Check if the version is the latest one.

YJA8223A

AREA:WY

10

02A8

1.16

1389EE

ROM NUMBER

REGION:2

REG CHK

SUM CHK

FL VERSION

CHIP VERSION

How to interpret the version code:

Number of releases on the same release date

Release date:(Example:2008.2.23) 8: Year 2: Month (1-9 [Jan-Sep], A-C [Oct-Dec]) 23: Day

Fixed

Y J A 8 2 2 3 A

38 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

9.1 PACKING

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.The mark found on some component parts indicates the importance of the safety factor of the part.Therefore, when replacing, be sure to use parts of identical designation.Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual.(In the case of no amount instructions, apply as you think it appropriate.)

NOTES:

WSXZT5 Only

Except WSXZT5

39DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

(1) PACKING SECTION PARTS LIST

(2) CONTRAST TABLE DV-310-S/WYXZT5, DV-310-S/WSXZT5, DV-310-K/WYXZT5 and DV-310-K/WSXZT5 are constructed the same except for the following:


> 1 Power Cable 1206158802

2 Audio/Video Cable 06CPBA2006

3 Remote Control See Contrast table (2)

4 Package Pad 792WHAA237

5 . . . . . . . .

6 . . . . . . . .

7 Operating Instructions (E/I) See Contrast table (2)

8 Operating Instructions (G/F) See Contrast table (2)

9 Operating Instructions (S/D) See Contrast table (2)

10 Operating Instructions (R) See Contrast table (2)

11 Polyethylene Bag,Instruction JB5KD000

12 Gift Sheet 791WHAA183

13 Package 792WHAA252

14 Gift Box See Contrast table (2)

15 Polyethylene Bag,INSTA5 791WHAA040


Mark No. Symbol and Description DV-310-S/WYXZT5 DV-310-S/WSXZT5 DV-310-K/WYXZT5 DV-310-K/WSXZT5

3 Remote Control 076E0PP031 076E0PP031 076E0PP041 076E0PP0417 Operating Instructions J2L30221B Not used J2L30221B Not used

(English/Italian)8 Operating Instructions J2L30222B Not used J2L30222B Not used

(German/French)9 Operating Instructions J2L30223B Not used J2L30223B Not used

(Spanish/Dutch)10 Operating Instructions Not used J2L30801B Not used J2L30801B

(Russian)

14 Gift Box 793WCDD660 793WCDD737 793WCDD711 793WCDD736

40 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

9.2 EXTERIOR SECTION

A

BD

A

C

BD

C

41DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

(1) EXTERIOR SECTION PARTS LIST

(2) CONTRAST TABLE DV-310-S/WYXZT5, DV-310-S/WSXZT5, DV-310-K/WYXZT5 and DV-310-K/WSXZT5 are constructed the same except for the following:


1 DVD MT PCB Assy A2L103A130

2 OPERATION PCB Assy See Contrast table (2)

3 . . . . . . . .

> 4 POWER PCB Assy A2L103A240

5 DVD MECHA Assy A2L101A650

6 Shield,21Pin 761WSA0237

7 . . . . . . . .

8 . . . . . . . .

9 Plate,Cover power 755WPAA035

10 Holder,FFC 761WPA0396

11 Cushion,Leg VEB1349

12 Cabinet,Top See Contrast table (2)

13 Spring Earth 743WKAA015

14 Cushion 65TS10-7.5 8965TS0610

15 Screw,Tap Tite(S)-Bind Wash. 816423063U

16 Screw,Tap Tite(B)-R (3x5.5) 815223055U

17 Screw,Tap Tite(B) (3x6.0) See Contrast table (2)

18 Screw,Tap Tite(B)Pan (3x6) 810913060U

19 Screw,Tap Tite(P) (2.6x8) 811022680U

20 Screw,Tap Tite(P) Bind WH7 8110I2680U

21 . . . . . . . .

22 . . . . . . . .

23 Front Cabi Assy See Contrast table (2)

24 Flap, DVD 712WPDA085

25 Spring, Flap-DVD 743WKA0052

26 Cord Connector (CD502) 06E82G3301

27 Cord Jumper (CD601) 122H0B1202

28 Cord Jumper (CD7301) 122H0C3002

29 Cord Jumper (CD605) 06CU241403

30 Flat Cable WAL6815038

31 Spring Earth 753WUAA013


Mark No. Symbol and Description DV-310-S/WYXZT5 DV-310-S/WSXZT5 DV-310-K/WYXZT5 DV-310-K/WSXZT5

2 OPERATION PCB ASSY A2L103A270 A2L109A270 A2L103A270 A2L109A27012 Cabinet,Top 702WSBA075 702WSBA075 702WSBA076 702WSBA07617 Screw,Tap Tite(B) (3x6.0) 810923060U 810923060U 810923060S 910923060S23 Front Cabi Assy 7A701B080A 7A701B080A 7A701B137A 7A701B137A

42 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

9.3 06 DVD MECHA SECTION

Applying positions AA, AB and AC for the grease are displayed for this section.Check if the correct grease is applied for each position.

NOTE:CLASS MARK

GREASE AA

AB

PART NO.

GEM1018

GYA1001

ACGEM1036

Cannot supply separately.If the repair is needed, replace the LOADER SUB ASS'Y.

PCB610(LOADING MOTOR PCB ASS'Y)

CD2302

Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.If the repair is needed, replace the DVD MECHA ASS'Y.

(SW PCB ASS'Y)

AB

AB

AB

AA

AB

AB

AB

SW1

PCB640

CD2001

SW2

CD2301

AC

AC

AB Lubricating OilGYA1001

DaifreeGEM1036

Pickup lenesesGEM1004GED-008

GreaseGEM1018

Note :

Lubricating OilGYA1001

43DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

06 DVD MECHA SECTION PARTS LIST


1 . . . . . . . .

2 Gear,Middle 92P100117A

3 Loading Motor 1515S98004

4 Pulley,Motor 92P100097A

5 FEED Motor 1515S98004

6 Cord Jumper (CD2001) 12C14O2202

7 Cord Jumper (CD2302) 12C1051601

8 Insulator (F) 92P200013A

9 Belt,Loading 92P200015A

10 Insulator (R) 92P200016A

11 Frame,main 92P100119A

12 Tray (R) 92P100151A

13 Holder ,Traverse 92P100125A

14 Gear,Pulley 92P100123A

15 Gear,Main 92P100124A

16 Gear,Feed 92P100116A

17 . . . . . . . .

18 Plate, Clamper 92P000023A

19 LOADER SUB ASSY (R) 92AAA0024A

20 Clamper 92P100122A

21 Screw,Pan (M1.7x3 P3) 814011730U

22 Screw,Pan (M1.7x2.3 P3) 814011723U

23 Rack,Loading 92P100121A

24 Gear,Motor 92P100088A

25 Feed Rack Assy 92AAA0017A

26 Screw,T-Tite(B) (M1.7x5.0 P3) 813381750U

27 Screw,Gear Feed 92P700007A

28 Cord Jumper (CD2301) 12C1061601

29 Switch (SW1) 0515S32003

30 Push Switch (SW2) 0500101036

31 Screw,Tap Tite(P) (2.6x8) 811022680U

32 Sems.Tap Tite(P) (2x8) 816112080U

33 Screw (Bind 2x8) 811022080U

44 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

10. SCHEMATIC DIAGRAM10.1 DVD MT PCB ASSY(1/6)

DVD MT PCB ASSY (1/6)(A2L103A130)

1 C40080.1 B

C4001

0.1 B

C410

1

270P

CHC4

102

270P

CH

C402

9

0.1

B

C400

2

10(212

5) B

C403

0

10(212

5) B

C400

6

1B

C403

6

0.1

B

C401

30.

1B

C408

9

0.01

5B

C409

0

0.1

B

C4037

13P CH

C400

3

0.1

B

C4033

12P CH

C400

5

0.1

B

C401

9

4.7

(212

5) B

C406

3

0.1

B

C403

81

B

C405

9

0.00

15B

C400

7

0.1

B

C402

0

0.1

B

C406

0

0.1

B

C405

7

0.1

B

C408

8

220P

CH

C405

8

0.1

B

C402

5

4.7(2

125) B

C404

50.

0068

B

C401

4

10 (212

5)B

C404

6 470

6.3V

YK_PC4

047

1000

6.3V

YK_P

C403

910

25V KA

_P

C404

4

100

10V

YK_P

R403

033

R402

933

R405

333

R405

433

R4014

15K

R401513K +-1%

R40168.2K +-1%

R401813K +-1%

R401913K +-1%

R402

4

100K

R4025

82

R400

515

0

R407

610

0

R403

3

33

R4039

5.1K +-1%

R403

410

K

R404

2

10K

R4002 10K

R4017 10K

R403

1

33

R400

1

33

R403

610

K

R403

710

K

TP40

44

TP40

06

X400

110

0GT0

2720

27M

Hz

W829

W808

W812

W813

W842

W81

6

W81

7

W83

6

W81

9

OF PRINTING AND SUBJNOTE:THIS SCHEMATIC DIAGR

DURING PLAYBACK.MEASURED WITH THE DIGITAL TESTER

NOTE:THE DC VOLTAGE EACH PART WAS

B400

8

BLM

18BD

102S

N1

B401

2

EBM

S160

808

A102

_RDC

45

IC4001MT1389FE/L-L

MPEG/MICON IC

1106107108109110111112113114115116117118119120121122123124125126127128

110

1112

1314

1516

1718

192

2021

2223

2425

2627

2829

330

3132

33 34 35 36 37 38 39

4

40 41 42 43 44 45 46 47 48 49

5

50 51 52 53 54 55 5

67

89

RF V+3A

TRIN

AL AR V+3

OP-

OP+

VSEL

1

I/XP

ADAC

_GND

MDI1

LIM

IT/T

ROUT

V20STBY

ABCDEF

LDO1LDO2

DMSOFMSO

TRCLOSE V+3TROPEN

TRSOFOSOOP+OP-IOA

TRINV1P4 V+1R8

RFLIMIT/TROUT

DABCFE

DQM0DQM1DWE#

DCAS#DRAS#

DQ0DQ1DQ2DQ3DQ4DQ5DQ6DQ7DQ8 V20DQ9

DQ10 V1P4DQ11DQ12DQ13DQ14 MDI1DQ15DBA0DBA1MA0 LDO1MA1MA2 LDO2MA3MA4 V+3MA5MA6 DMSOMA7MA8 FMSOMA9

MA10 STBYMA11

SDCLK IOASFLASH_CSSFLASH_DO TRSOSFLASH_DISFLASH_CK FOSO

USB_P_ON-LUSB_FLAG USB_P_ON-L

USBNUSBP USBPFLDC--28V USBN

FLDC+V+3E V+3D

IRFP_DO

STBFP_DI

FP_SCKV+1R8

USB_GNDV+3D

USB_

FLAG

SFLA

SH_C

S

SFLA

SH_D

O

SFLA

SH_D

I

SFLA

SH_C

K

FP_S

CK

FP_D

I

FP_D

O

DQ15

RESE

T

DQ0

DQ1

DQ2

DQ3

DQ4

DQM

0

STB

DQ5

DQ6

DQ7

IR

FROM/TO MEMORY/USB

FROM/TO LOADER/MOTOR DRIVE

(DVD MT PCB)MPEG/MICON/DSP SCHEM

1.08 1.11 0.98 0.97 0.00 1.82 3.35 3.37 3.10 3.13 1.53 1.27 1.42 0.00 3.45 0.00 0.00 1.41 3.31 1.253.20 1.30 1.59

0.833.151.811.30 0.731.201.341.341.141.57 1.523.313.293.313.193.113.271.073.311.393.273.323.183.21

2.17

2.18

2.19

2.22

2.26

2.27

0.00

1.81

3.17

2.02

1.40

0.62

0.17

0.17

2.44

2.44

3.31

2.07

1.00

2.89

3.22

3.10

3.08

1.54

3.09

3.30

3.30

0.00

0.73

1.81PAD_VRT

PRST

#

DVDD

18

DQM

0

RD15

35 GPIO634 GPIO433 GPIO3/INT#

128

127

126

AADV

SS(A

DC)

AADV

DD(A

DC)

APLL

VDD(

A)

APLL

CAP(

A)

ADAC

VSS2

(A)

ADAC

VSS1

(A)

ADAC

VDD1

(A)

ADAC

VDD2

(A)

RD0

RD1

RD3

RD4

RD2

RD5

RD6

RD7

DVDD

33

IR_I

N

ICE

SF_C

S

SF_D

O

SF_D

I

SF_C

K

AGND

18(R

F)

AVDD

18(R

F)

RFIP

(RF)

RFIN/OPOUT(RF)

RFH/OPINN(RF)

RFG/OPINP(RF)

ALF/

ASDA

TA0/

GPIO

(A)

ALS/

ALRC

K/GP

IO(A

)

AL/A

SDAT

A1/G

PIO(

A)

AVCM

(A)

AR/A

SDAT

A2/G

PIO(

A)

ARS/

ABCK

/GPI

O(A)

ARF/

ACLK

/GPI

O(A)

ADVC

M/G

PIO2

0(AD

C)

AKIN

1/GP

IO21

/AUD

IO_M

UTE(

ADC)

AKIN

2/GP

IO19

/AUD

IO_M

UTE(

ADC)

UP1_

7/SD

A

UP1_

6/SC

L

VDD18_USB

GND_USB

VDD33_USB

USB_DM

USB_DP

FG/GPIO2

FOSO

TRSO

STBY(TR OPEN)

IOA(TR CLOSE)

FMSO

DMSO

AGND

XTALO

REXT

MDI1

LDO1

LDO2

XTALI

AVDD33_2

V20

V14

DVDA(RF)

DVDB(RF)

DVDC(RF)

DVDD(RF)

DVDE(RF)

MDI2

DVDF(RF)

AVDD18_2(RF)

AVDD33_1(RF)

NC

45DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

3

2

C409

1

0.1

B

C401

30.

1B

C4072100PCH

C4012100PCH

C406

3

0.1

B

C405

9

0.00

15B

C402

3

0.1

B

C406

0

0.1

B

C405

7

0.1

B

C4104

0.01 B

C4073

0.1 B

C4071

0.1 B

C4074

0.1 B

C40661 B

C404

50.

0068

B

C401

4

10 (212

5)B

C4064

0.1 B

C404

6 470

6.3V

YK_P10

010

VYK

_P

C408

0

220

6.3V YK

_P

R4066 33

R4032 33R4038 33

R406

1

75+-

1%R406

0

75+-

1%

R406

2

75+-

1%

R4058

R400

6

100

R404

5

68K

R4075

4.7K

R404

6

1.2K

+-1%

R405

9

75+-

1%

R4027 33

R406

510K

JG4092JG4093

JG4091

JG4094TP4110

W83

4

W83

3

W825

W81

9

W832

W839

W849

W850

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.OTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

B4007MMZ1608R102CT

B401

2

EBM

S160

808

A102

_RDC

45

B401

0EB

MS1

6080

8A1

02_R

DC45

NR40024D03WGJ0330T5E

IC40

03R3

112N

291A

-TR-

FARE

SET

IC

1 2 3

45

19FE/L-L

MICON IC

1011021031041051061071081091101112 100

9 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

6566

6768

6970

7172

7374

7576

7778

7980

8182

8384

8586

8788

8990

9192

9394

9596

979899

V+3

V+3

V+3AV+3

V+3

V+1R8PWDN#R/CRADAC_GNDB/CBD_GNDG/Y

C/V

R/CRB/CBG/YC/VRXD/SQTXD/LEI/XPVSEL1

XAMUTE

ADAC_GNDASPDIFVSEL1ALPWDN#ARXAMUTEPWDN#ASPDIFTXD/LE

10K

GNDRXD/SQ

TRCLOSE

TROPEN

MA3MA2MA1

MA0

MA10

DBA1

DBA0DRAS#DCAS#DWE#

MA4

MA5

MA6

MA7

MA8

MA9

MA11

SDCLK

DQM1

RXD/SQTXD/LE

RESE

T

DQ15

DQ14

DQ13

DQ12

DQ11

DQ10

DQ9

DQ8

DQM

0

DQ5

DQ6

DQ7

V+3

V+3D

TO AUDIO JACK

TO VIDEO JACK

(DVD MT PCB)SP SCHEMATIC DIAGRAM

NC0

0.00 1.41 3.31 1.253.20 1.30 1.59 0.00 2.69 2.70 2.58 3.29 3.29 0.66 0.00 1.28

0.00

3.28

3.28

1.58

3.28

3.27

1.81

1.70

0.35

0.39

2.32

2.29

2.94

2.19

0.57

0.45

0.75

0.00

1.27

1.81

2.72

3.35

2.32

1.40

1.54

0.58

0.44

0.45

3.29

3.29

1.53

2.43

0.940.850.821.100.001.041.291.360.833.151.811.30 0.731.523.31

FROM/TO POWER PORT

DMG099PCB130

DVDD

18

DQM

0

RD15

RD14

RD13

RD12

RD11

DVSS

RA11

RA6

RA4

CAS#

RAS#

DVSS18

RA0

DVDD33

GPIO7/CKE

GPIO8

GPIO13

GPIO10

SDCLK

DQM1

62 RD1063 RD964 RD8

RA7

RA8

RA9

RA5

98

97

99

DACVDDC(V)

GPIO11

DVDD18

GPIO9

DACV

DDA(

V)

DACV

DDB(

V)

SPDIF/GPIO12

AADV

SS(A

DC)

AADV

DD(A

DC)

APLL

VDD(

A)

APLL

CAP(

A)

ADAC

VSS2

(A)

RD4

RD5

RD6

RD7

DVDD

33

DVDD33

RA10

RA1

RA2

RA3

BA1

RWE#

VREF(V)

BA0

B/CB

/PB(

V)

R/CR

/PR(

V)

G/Y(

V)

ADVC

M/G

PIO2

0(AD

C)

DACVSSC(V)

FS(V)

CVBS/C(V)AKIN

1/GP

IO21

/AUD

IO_M

UTE(

ADC)

AKIN

2/GP

IO19

/AUD

IO_M

UTE(

ADC)

NC

V_OU

T

VSS

NCCT

VDD

3.3

3.3

0.0

1.9

46 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

10.2 DVD MT PCB ASSY(2/6)


IC4005 M12L64164A-7TG64Mbit(4M*16) 143MHz SDRAM IC

110

1112

1314

1516

1718

192

2021

2223

2425

262728

29

3

3031

3233

3435

3637

3839

4

4041

4243

4445

4647

4849

55051

5253

54

67

89

Q4KR

US

C4049

0.1 B

C4048

0.1 B

C4055

0.1 B

C4052

0.1 B

C412

2

C405

1

0.1

B

C405

0

1000

6.3V

YK_P

R4026

10K

R4020

10K

TP4001

W844

W810

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

DURING PLAYBACK.MEASURED WITH THE DIGITAL TES


C4053

0.01 B

C4054

0.01 B

C404

3

0.01

B

DQ15 DQ0

SFLASH

DQ14 DQ1 SFLASH

DQ13 DQ2

DQ12 DQ3SFLASH_CSSFLASH_CKSFLASH_DI DQ11 DQ4

SFLASH_DODQ0DQ1DQ2DQ3 V+5V_UDQ4 DQ10 DQ5DQ5DQ6DQ7 DQ9 DQ6DQ8DQ9 USB_FLA

DQ10DQ11DQ12DQ13 DQ8 DQ7DQ14DQ15MA0MA1MA2MA3 DQM0 USB_P_MA4MA5MA6 DQM1 DWE#MA7MA8MA9 SDCLK DCAS#

MA10MA11DWE# DRAS#DQM1DQM0

DCAS#DRAS#

DBA1DBA0 MA11 DBA0 FLDC-

SDCLK -28VUSB_P_ON-L

USB_FLAG MA9 DBA1 FLDC+USBNUSBPFLDC- MA8 MA10

-28V V+3EFLDC+

V+3E MA7 MA0 IRIR FP_D

FP_DOSTB MA6 MA1 STB

FP_DI FP_DFP_SCK MA5 MA2 FP_SC

USB_GND

MA4 MA3

V+3DD_GND

USBN

USBP

USB+5V

(DVD MT PCBMEMORY/USB SCHEMA

FROM/TO MPEG/MICON/DSP

FROM POWER PORT

NC

VSS

DQ12

DQ11

DQ10

DQ9

VDDQ

DQ8

VSS

UDQM

CKE

NC

A9

A10/AP

A0

A2

A1

A3

VDDVSS

A4

NC/RFUNC

3.3

1.5

3.3

1.5

1.5

0.0

1.5

1.5

3.3

1.5

1.5

0.0

1.5

3.3

2.0

3.3

3.3

3.3

3.3

3.3

1.0

0.0

1.7

1.7

1.7

1.7

3.30.0

1.7

1.7

1.7

1.7

1.7

1.7

1.7

1.9

1.7

1.9

0.0

1.5

3.3

1.5

1.5

0.0

1.5

1.5

3.3

1.5

1.5

0.0

1.5

0.0

WE#

CAS#

RAS#

CS#

VDD

CLK

A11

A8

A7

A6

A5

BA1/A12

BA0/A13

LDQM

VDD

DQ7

DQ3

DQ4

VDDQ

DQ5

DQ6

VSSQ

VSSQ

DQ15

VSSQ

DQ13

VDDQ

DQ14

DQ0

VDDQ

DQ1

DQ2

VSSQ

47DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

FCAUTION: DIGITAL TRANSISTOR

IC4004AT26DF161-SU

16M SERIAL FLASH IC

12

34 5

67

8

D4005

EC31QS04

(SCHOTTKY 3.0A)

Q4003KRC103SRTK

USB_P_ON-H

L4001DLP11SN201HL2L

1

2 3

4

CP400200_6232_011_006_800+

1

1011

23456789

D4002

AVRL161A1R1NT

D4003

AVRL161A1R1NT

CP4004B4B-PH-SM4-TB(LF)(SN)

1234

C413

5

100P

CH

C413

4

33P

CH

C413

3

100P

CH

C413

2

33P

CH

C407

7

0.1

B

C4062

0.1 B

C407

6

0.1

B

C412

2

100P

CH

C411

4

1B

C414

2

100

10V

YK_P

C407

8

1025

VKA

_P

R404

8

22K

R404

4

10K

R404

0

10K

R4043

33

R401

0

100K

R400

7

10K

R4021

10K

TP4035

TP4004

W80

9

W844

W831

W810

LAYBACK.D WITH THE DIGITAL TESTER

OLTAGE EACH PART WAS

IC4007R5523N001B-TR-F

HIGH SIDE SW IC

12

3 45

SFLASH_CS

SFLASH_DO

SFLASH_CK

SFLASH_DI

V+5V_USB

USB_FLAG

USB_P_ON-L

FLDC--28VFLDC+

D_GND

V+3EIRFP_DOSTBFP_DIFP_SCK

USBN

USBP

USB+5V

USBNUSBP

USB+5VGND(USB)

FROM/TO DISPLAY

DVD MT PCB) SCHEMATIC DIAGRAM

2.83

1.16

3.27

3.27

3.28

1.09

0.98

3.28

NC

VCC

HOLD#

VSS

WP#

SO

CE#

SCK

SI

0

03.3

EN

GND

/FLG VIN

VOUT 5.3

5.3

0

3.3

3.3

DGND

FLDC+-28VFLDC-

V+3EIR

STBDO (F to M)

DI (M to F)CLK

DGND

DMG099PCB130

48 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4



:SINCE THESE PARTS MARKED BYCAUTIONDESCRIBED IN PARTS LIST ONLY.CRITICAL FOR SAFETY,USE ONES

ARE

DANS LA NOMENCLATURE DES PIECES.N’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE

:LES PIECES REPAREES PAR UN ETANTATTENTION

CP2301LD07T2-24ND-03

PICK-UP(GOLD)

1

10111213141516171819

2

2021222324

3456789

CP230200_6232_005_006_800+

LOADING

12345

Q2301KTC3875S_Y_RTK

VCR_CTLQ2302

KTA1504S_Y_RTK

LD DRIV for CD

Q2303KTA1504S_Y_RTK

LD DRIV for DVD

CP230300_6232_006_006_800+

SLED/SPINDLE

123456

IC23MOT

1516

1718

1920

2122

2324

2526

2728

30

Q230

6UM

6K1N

VR C

TL

1 2 3

456

D230

1

BAT5

4WS

D230

2

BAT5

4WS

C2303

0.1 B

C2301

0.1 B

C2302

0.1 B

C23110.1 B

C2307

0.1 B

C232

2

0.22

BC2

323

0.22

B

C2304 10016V KA_P

C2306

10010VYK_P

R2312

8.2K +-1%

R234

1

10K

R234

3

10K

R2313

10K +-1%

R2310

10K

R2316

3.3K

R2307

100K

R2306

100K

R230

8

10K

R2325

470 +-1%

R2309

10K

R231

9

10K

R234

2

10K

R2326

1 1/4W(2125)

R232

8

10K

R234

4

10K

JG2320JG2321JG2322

JG2323

JG2329

JG2304JG2305

JG2306

JG2309

JG2310JG2311JG2312

JG2313

JG2314

JG2315

JG2316JG2317JG2318JG2319

JG2308JG2307

JG2302

JG2303

TP2330

JG2324JG2325JG2326JG2327JG2328

TP2342JG2330

TP2341

TP2333

W81

4

W815

W802

W83

0

DURING PMEASURE

NOTE:THE DC V

IOA

V+5S

V+5S

FV20

EDC

IOARFBA

MDI1

T+T-F+F-

LOAD-FM

SOTR

SOST

BYLOAD+

V+6ALIMIT/TROUT

TRIN

V+3F

OP-OP+

MOT_SLED-MOT_SLED+

MOT_SPDL+MOT_SPDL-

V+3F

MOT

_SLE

D+M

OT_S

LED-

T- T+

LOADER/MOTOR DRIVE SCH(DVD MT PCB

NCNC 3.5

5.56

0NC 2.03

3.24

13.2

13.2

13.2

0

1.38

5.77

2.92

2.81

2.88

2.82

LOAD+LOAD-

GNDOPEN

CLOSE

NC

VRCOM

TRKG DRVTRKG RTN

FOCS RTNFOCS DRV

VCC

D

B

VR780(CD)

VRF(RF_OUT)SW1(DVD/CD)

C

E

VSF

GND

AVR650(DVD)

GND

GNDLD_DVD(650)

LD_CD(780)PD/GND

NC

VOTK-

VOTK+

VOLD+

VOLD-

VCTL

Vcc2

GND

VINLD

TRB_2

VINTK

BIAS

MUTE

PGND

OPOUT

OPIN

SW(GND)LIMIT SW

SLD-SLD+SPD-SPD+

5.0

0.0

0.0

1S1D

1G 2D2S2G

0.0 0.0 0.0

0.2 4.9 0.0

49DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

Q2304KTA1504S_Y_RTK

LD DRIV for CD

Q2305KTA1504S_Y_RTK

LD DRIV for DVD

Q2302KTA1504S_Y_RTK

LD DRIV for CD

Q2303KTA1504S_Y_RTK

LD DRIV for DVD

IC2301 AM5766MOTOR DRIVER IC

110

1112

131415

1617

1819

2

2021

2223

2425

2627

28

293

30

45

67

89

C23120.1 B

C2305

0.1 B

C2308

10p CH

C232

1

100

10V

YK_P

C232

0

100

10V

YK_P

R2311

18K +-1%

R2317

8.2K +-1%

R2312

2K +-1%

R2325

470 +-1%

R2318

47K

R2327

47K

JG2329

JG2301 TP2332

TP2301

TP2329

TP2342JG2330

TP2341

TP2331

W805

W806




NR23014D03WGJ04R7T5E

V20ABCD

V+3F EFMDI1LDO2LDO1IOALDO1V1P4TRINSTBYDMSOFMSOTRCLOSETROPENTRSOFOSOOPOOP+LDO2OP-RF

LIMIT/TROUT

V+3FV+5SV+6A

D_GNDM_GND

V1P4

FOSO

DMSO

TROP

EN

TRCL

OSE

MOT

_SPD

L-M

OT_S

PDL+

F+ F-

LOAD

+LO

AD-

RIVE SCHEMATIC DIAGRAMDVD MT PCB)

NC

NC

NC

1.46

3.13

13.13

0

3.51

3.34

5.6

NCNC 3.5

5.56

0

NC 2.03

3.24

13.2

13.2

13.2

0

1.38

5.77

2.92

2.81

2.88

2.82 2.77

2.91

1.69

3.25

3.26

3.22

5.76

FROM POWER PORT


Vcc1

VOTR-

VOTR+

VOSL+

VOSL-

VOFC-

VOFC+

REGO 1

VINSL+

REGO 2

TRB_1

VINFC

REV

FWD

VOTK-

VOTK+

VOLD+

VOLD-

VCTL

Vcc2

GND

VINLD

TRB_2

VINTK

BIAS

MUTE

PGNDPGND

OPOUT

OPIN

3.3

0

3.3

0

3.33.3

3.12.5 2.5

3.1

2.0 2.0

DMG099PCB130

50 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4



6 H E

J8001RCA-117-01

COAXIAL

12

C8051

4716V NA_P

C8053

4716V NA_P

Q8005KTC3875S_Y_RTK

COAXIAL DRIV K

X

C804

2

100P

CH

C8036

1 B

C8074

330PCH

C8038

150V KA_P

R804

0

100K

R8048

470K

R8060

470K

R8035

2.4K

R8059

10K +-1%

R8049

10K +-1%

R803

8

220

R803

6

3.9K

R803

7

1.8K

R8039

68

R807

0

22K

W840

OF PRINTING AND SUBJECT TO CHANGE WITHNOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT



B800

4

EBM

S160

808

A102

_RDC

45

ASPD

IF

XAM

UTE

V+5V

_A

D_GNDV+12AT

V+12

XAMUTEASPDIF

ALAR

GND

AL

AR

AUDIO_LAUDIO_R

V+5V_AGND

(DVD MT PCBAUDIO JACK SCHEMAT

2.8

2.1

5.0

FROM POWER PORT

FROM MPEG/MICON/DSP

FROM/TO VIDEO JACK

51DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

4

5

H1H2

E1

23

CAUTION: DIGITAL TRANSISTOR

Q8020KTC2875-B

MUTE SW

Q8019KTC2875-B

MUTE SW

Q8018KTC2875-B

MUTE SW

Q8021KTC2875-B

MUTE SW

Q8014KTA1504S_Y_RTK

JACK MUTE(H:ON)

IC80

03RC

4580

IDR

AUDI

O AM

P IC

1234

5 6 7 8

Q8013KRC407-RTK/P

XAMUTE(L:ON)

C807

8

330P

CH

C807

7

330P

CH

C8072

0.1 B

C8067

68P CH

C8069

68PCH

C805

7

560P

CH

C805

6

560P

CH

C805

8

0.1

B

C805

9

0.1

B

C8073

4716V YK_P

C8070

4716V YK_P

C806

6

100

10V

YK_P

R8079

220 +-1%

R8078

470

R8081

470

R8080

220 +-1%

R8083

470

R8082

220 +-1%

R8076

470

R8077

220 +-1%

R801

4

4.7K

R806

9

22K

R8048

470K

R8060

470K

R8084

220 +-1%

R8085

220 +-1%

R8059

10K +-1%

R8049

10K +-1%

R8066

10K +-1%

R807

4

22K

R807

3

22K

R8067

27K +-1%

R8061

10K +-1%

R8063

27K +-1%

R8057

22K

R805

1

4.7K

R805

6

4.7K

R807

0

2.2K

UBJECT TO CHANGE WITHOUT NOTICE.AGRAM IS THE LATEST AT THE TIME

XAM

UTE

V+12

AT

AUDIO_L

AUDIO_R

V+12

DVD MT PCB)SCHEMATIC DIAGRAM

6.3 6.3 6.3

6.3 6.3 6.30

12.5

+-

-+

+VS

-VS

L R

-1.1

0

0

-1.20

0

-1.2

0

0

-1.1

0

0

0.30.1

0

2.7

DMG099PCB130

J8003RCA-207B(CUSN)-02

AUDIO OUT

52 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4



IC7301 LA73054VIDEO DRIVER 6CH IC

110

1112

1314

1516

1718 19

2

2021

2223

2425

2627

2829

3

3031

3233

3435

36

45

67

89

L7301

22uH 0405

Q730

1RN

4903

(T5L

_F_T

)IN

CTL

1 2 3

456

Q7305RN4903(T5

CTL 21PIN

12

3

D7305

MA111D7

306

MA1

11

Q7302KRC103SRTK

P-H/I-L

C7305

0.1 B

C7306

1 B

C7310

1 B

C7304

0.1 B

C7313

0.1 B

C7312

0.1 B

C7308

1 BC7309

1 B

C7307

1 B

C731110010V YK_P

C730

3

470

6.3V YK

_P

R7305

47K

R7301

1K

R730

7

47K

R7302

1K

TP4048

TP4047

TP7303

TP7302

W889

OF PRINTING AND SUBJECT TO CHANGNOTE:THIS SCHEMATIC DIAGRAM IS THE LA



RXD/

SQ

C/V

RXD/SQ

TXD/LE

TXD/LERXD/SQ

VSEL1I/XP

R/CRB/CBG/YC/V

VSEL1

G/Y

B/CB

R/CR

AUDIO_L I/XPAUDIO_R

V+5V_A

P-H/I-L

V+5V

V+5V_AV+5V

V+6A

D_GND

D_GND

VSEL

1

1.26 01.56

4.97 4.974.97

00

0

NC

NC

NC

VCC1

CVBS in

SQ

LE

C in

GND11

Y1 in

Y2 in

MUTE2

CB in

AMP2

CR in

GND12

REG

GND26

CR out

GND25

CB out

VCC22

Y2 out

GND24

GND23

Y1 out

GND22

C-DC out

C out

GND21

CVBS out

VCC21

DRIVE1

AMP1

LPF

(9dB=H,6dB=L)

(P=H,I=L)

(9dB=H,6dB=L)

(ON=H,OFF=L)

DRIVE2(1D=H,2D=L)

(1D=H,2D=L)

MUTE1(ON=H,OFF=L)

IN SW(RGB=H,YUV=L)

YC-MIX(MIX=H,OFF=L)

0

0

0

0

0

0

0

0

0

0

2.6

0

0

2.5

2.6

2.7

5.0

2.5

2.5

2.8

0

2.9

4.1

2.9

0

0

0

0

2.8

0

0

2.8

2.0

0

0

5.0

3.3

0

0

U/B

Y/G

V/R

(DVD MT PCBVIDEO JACK SCHEMAT

FROM MPEG/MICON/DSP

TO AUDIO JACK

FROM POWER PORT

53DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

7 89 10

H1H2

E

H1H2

EJ7302

RCA-405A(CUSN)-08

CVBS/Y/U/V1

23

4

56

D731

1

UDZS

NP6.

8B

D731

2

UDZS

NP6.

8B

D731

0

UDZS

NP6.

8B

CP7301IMSA-9604S-12C

VIDEO/AUDIO for 21PIN

1

101112

23456789

IC7302SN74CBT3257PWR

4CH BUS SW IC

1

1011

1213

1415

16

23

45

67

8 9

Q7305RN4903(T5L_F_T)

CTL 21PIN CTL

12

3 45

6


C731

5

0.00

1B

C732

222

pCH

C731

9

1000

6.3V

YK_P

C731

8

1000

6.3V

YK_P

C731

7

470

6.3V

YK_P

C731

6

470

6.3V

YK_P

R731

9

1.2K

R732

0

1.2K

R732

1

1.2K

R731

8

75 1/10

W+-1%

R731

6

75 1/10

W+-1%

R731

7

75 1/10

W+-

1%

R731

5

75 1/10

W+-1%

G AND SUBJECT TO CHANGE WITHOUT NOTICE.ATIC DIAGRAM IS THE LATEST AT THE TIME

B730

5BL

M18

BD10

2SN1

B730

4BL

M18

BD10

2SN1

B730

1

BLM

18BD

102S

N1

B730

2

BLM

18BD

102S

N1VSEL

1

PWDN

#

AUDI

O_R

AUDI

O_L

RXD/

SQ

G/Y_OUT

B/U_OUT

R/V_OUTP-H/I-L_RGB-H

ASP/FS

U_OU

T

V_OU

T

Y_OU

T

VSEL

1

00

0

3.15

0.92

0

FROM/TO POWER

GND

GND

RGB-HFS

AUDIO LGND

AUDIO R

CVBSGND

(CP503)

G

B

R

YU V CVBS

CVBS OUT

3.33.3

1.8

2.4

2.6

1.3

2.5

2.5

2.4

2.4

1.3

5.0

0

0

GND

VCC

2B1

2B2

2A

1B2

1A

4B1

4B2

4A

3B1

3B2

3A

/OE1B1

S

NC

NC

NC


DMG099PCB130

54 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4



C409

5

476.

3VKA

_P


ARE



CP4003A2001WV2-16P

1

10111213141516

23456789

IC4006LD1117AL-ADJ-AA3-A-R

REG+1.8V IC

123

C408

6

1B

C411

2

0.00

1B

C409

6

1B

C411

6

0.00

1B

C409

8

C409

3

1B

R401

3

39+-

1%

R4012

68 +-1%

R4011

15

TP4002

W820

W845

DURING PLAYBACK.MEASURED WITH THE DIG

NOTE:THE DC VOLTAGE EACH PA

(DVD MT PCBPOWER PORT SCHEMA

(CP502)

GNDP.CON+5V

FL DC-FL DC+

AT+3.3V

P.CON+12V

GND(M)

GND(D)

P.CON+6V

AT+3.3V

-28V

P.ON-H

GND

AT+12V for MUTE

USB+5V

ADJVOUTVIN

GND(USB)

FROM/TO POWER

55DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

IC4009BA00BC0WFP

13

V+5USB REG(1.3W/1A) IC

1 2 4 56

-AA3-A-R

1

Q4001KTC3875S_Y_RTK

ADACVDD REG

C409

6

1B

C405

6

0.01

B

C414

0

0.00

1 B

C401

0

1B C4

011

0.1

B

C409

8

1B

C409

9

0.00

1B

C410

0

220

6.3V YK

_P

C413

7

1025

V KA_P

C414

1

100

10V

YK_P

R403

5

430

+-1%

R400

8

1.5K

+-1%

R401

3

39+-

1%

R4072

15K+-1%

R4063

10K R4073

220

R407

4

4.7K

+-1%

R402

2

100K

TP4036

W820

W822

W821

W826


DURING PLAYBACK.MEASURED WITH THE DIGITAL TESTERHE DC VOLTAGE EACH PART WAS

B4002EBMS160808A102_RDC45

B4001EBMS160808A102_RDC45

V+5V V+5VV+12AT V+12ATV+12 V+12

D_GND

V+5VD_GNDV+6A

V+6A V+6AV+5S V+5SV+3F V+3F

D_GNDM_GND

V+5V_USBV+3 V+3V+3E V+3EV+1R8 V+1R8

V+3A

ADAC_GND

PWDN#FLDC-FLDC+-28VD_GND

V+3D_GND


(VIDEO/OPT/COAX)

(AUDIO AMP)(AUDIO MUTE)

(MPEG/SDRAM/FLASH)

(F/E)(OPU)(MOTOR)

(FIP/LED/IR)

(CORE)ADJ

0

V_C V_ADJV_OUTGNDV_IN

6.0 1.34.7 5.2

5.0

3.93.3

PCB130DMG099

TO MEMORY/USB


TO LOADER/MOTOR DRIVE

TO VIDEO JACK

TO AUDIO

56 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

10.7 OPERATION PCB ASSY

OPERATION PCB ASSY(WYXZT5 : A2L103A270)(WSXZT5 : A2L109A270)

SW667:POWERSwitch

110

11

1213141516171819

2

20212223

2425

2627

2829

3

3031

3233

34 35 36 37 38 394

40 41 42 43 445

67

89

SW660

EVQ11L05R

STOP

SW663

EVQ11L05R

PLAYSW662

EVQ11L05R

+SKIP

SW665

EVQ11L05R

PAUSESW664

EVQ11L05R

-SKIP

SW667

EVQ11L05R

POWER

SW653

EVQ11L05R

ENTER

SW654

EVQ11L05R

RIGHT

SW657

EVQ11L05R

UP

SW659

EVQ11L05R

LEFT

SW661

EVQ11L05R

HOMEMENU

SW666

EVQ11L05R

EJECT

SW652

EVQ11L05R

DOWN

SW658

EVQ11L05R

TOPMENU

SW656

EVQ11L05R

MENU

SW655

EVQ11L05R

RETURN

V651HNV-08SS84

1112131415161718192021222324252627283132

Vout

B+GND

OS651KSM-2001TC2P

123

CP60

3B2

013H

02-3

P

123

CP60

4B2

013H

02-3

P

123

D658 1SS133

D651 1SS133

D654 1SS133

D656 1SS133

D659 1SS133

D652 1SS133

D655 1SS133

D657 1SS133

C658

C676

C675

1B

C651

0.1

B

C653 47

6.3V KA

_P

C674

476.

3VKA

_P

R666

47 1/4W

TP66

2

OF PRINTING AND SUNOTE:THIS SCHEMATIC DIA



IR

V+3E

P16

P15

P14

P13

P12

P11

P10

P9 P8 P7 P6 P5 P4 P3 P2 P1 GR8

GR7

SW2

SW1

P8 P9 P10

P11

P12

P13

P14

P15

P16

P7

P6

P5

P4

P3

P2

P1

GR8

GR7

GR6

GR5

GR4

GR3

GR2

GR1

IRV+

3E

GND

SW1

SW2

(OPERATION PCDISPLAY SCHEMATIC

PCB271DEG150

NC

STB

12

VDD

23

-12.0

-6.0

-18.0

0-19.0 -15.6-19.0-9.5-13.0-9.5-12.6-13.0-6.0

LED1

LED2

LED4

CLK

34VD

D44

NC

NC

NC

NC

-18.0

-18.0

-18.0

-18.0

-18.0

-18.0

-18.0

-18.0

-16.0 -16.0 -16.0 -16.0-16.0 0

K2

K1

DI

DO

OSC

GND

P16

P15

P14

P13

P12

P11

P10

P9P8

P7P6

GR12

P5

P4

P3

P2

P1

-28V

GR10

GR11

GR9

GR8

GR7

GR6

GR5

GR4

GR3

GR2

GR1

GND

LED3

-16.0-18.0-18.0-18.0

3.3

3.3

V+3E

IR

-25.

1-2

5.1

-20.

5-2

6.8

-26.

8-2

6.8

-20.

5-2

0.5

-22.

7-2

0.5

-20.

5-2

2.7

-26.

8-2

6.8

-20.

5-2

2.7

-22.

7-2

6.8

-19.

7-1

9.7

FL+

FL+

P16

P15

P14

P13

P12

P11

P10

DVDCD TRACK ALL REPEA

P9 P8 P7 P6 P5 P4 P3 P2 P1 G8 G7

GND PO

WER

SW2

GND

POW

ERSW

2GN

D

IC651PT6315

FIP DRIVER IC

57DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

SwitchesSW652 : DOWNSW653 : ENTERSW654 : RIGHTSW655 : RETURNSW656 : MENUSW657 : UPSW658 : TOP MENUSW659 : LEFTSW660 : STOPSW661 : HOME MENUSW662 : + SKIPSW663 : PLAYSW664 : – SKIPSW665 : PAUSESW666 : EJECT

1

110

11

1213141516

23

4

40 41 42 43 44

56

78

9

SW66

8

EVQ1

1L05

R

USB

110111213141516171819 256789

CP605A2001WR2-4P

1234

CD6012H0B1202

FFC(1.0mm pitch)

CD605CU241403

SHIELD CABLE

D665

1SS1

33

D669

1SS1

33

MS1

_2

CP60100_6232_011_102_800+

1

1011

23456789

CP602USB-A1D102F-4B4N

USB CONNECTOR

1234

C658

0.1

B

C676

0.1

B

C610

47P

CHC611

47P

CH

C675

1B

C608

0.01 B

C654

0.01

B

C601

1B

C604

33P CHC605

1 B

C653 47

6.3V KA

_P

R658

10K

R655

1K R656

1KR657

10K

R662

100K

R654

2.2

TP66

2

W80

3

W804

W806(W802)

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

B602

HCB2

012K

-600

T25

(60

OHM

2.5

A)B601

HCB2012K-600T25

(60 OHM 2.5A)

FLDC-

FLDC+

P7 P6 P5 P4 P3 P2 P1 GR8

GR7

GR6

GR5

GR4

GR3

GR2

GR1

SW2-28V

SW1USB+5V

P14

P15

P16

USBNUSBP

STB

FP_SCK

FP_DI

FP_DO USB+5V

USBPUSBN

FP_SCKFP_DISTBFP_DOIRV+3E

GR3

GR2

GR1

FLDC+-28VFLDC-

V+3E

GND

PERATION PCB)CHEMATIC DIAGRAM

NC

STB

12

VDD

3.2

0

0

0-19.0 -15.6.0

LED1

LED2

LED4

CLK

VDD

44

.0 -16.0 -16.0 0

0

2.9

3.2

0.7

3.4

NC

K2

K1

DI

DO

OSC

GND

P16

P15

P14

GR3

GR2

GR1

GND

LED3

0

0

0

NC

NC

3.3

3.3

+5V

GND

USB_DNUSB_DP

-25.

1-2

5.1

-25.

1-2

5.1

-25.

1-2

5.1

-25.

1-2

5.1

-20.

5-2

6.8

-26.

8-2

6.8

-20.

5-2

0.5

-22.

7

-22.

3-2

2.3

FL-

FL-

LL REPEAT A B

P7 P6 P5 P4 P3 P2 P1 G8 G7 G6 G5 G4 G3 G2 G1

DGND

FLDC+-28VFLDC-

V+3EIR

STBDO (F to M)

CLK

DGND

DI (M to F)

USBN

USB+5VGND(USB)

USBP

PCB270DEG149

IC FROM/TO MEMORY/USB

58 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

10.8 POWER PCB ASSY(1/2)

POWER PCB ASSY (1/2)(A2L103A240)

* The parts except mark cannot be changed. On that occasion, replace whole Assy.

F501T1.6A_L_250V

51MS016L

L501SS11V-03550NT-CH

COIL,LINE FILTER

1 2

3 4

FH501EYF-52BCY

FH502EYF-52BCY

123

4

R502

_1

1.5

1W

R510_1

2.7 1W

1.6A 250V

1.6A 250V

REPLACE ONLY WITH THE SAME TYPE FUSE:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,CAUTION

N’UTILISER QUE DES FUSIBLE DE MEME TYPE:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIEATTENTION

IC501KIA431A-AT

VOLTAGE CTL IC

123

R511

68 1/4W

R507

10 1/4W

J501YKE31-0148N

AC INLET

12

T50181291354

10

11

12

13

14

15

16

2

3

4

6

7

8 9

CD501_206158802

AC220V-240V_50Hz/60Hz(EU)

C520

SH501YQ-12

C521

C511

_2

4740

0VNH

G

C523

470

25V

YKP


ARE



D508

MTZ

J5.6

B

KTC

IC50

2ST

R-A6

159M

POW

ER C

TL IC

1 2 3 4

5678

D503

1N4005-EIC

D509

RL10

6F-E

D515

1S40-E

D506

1N4005-EIC

D519

1F5-E

D527

SR240-F

D510

SF26-F

D512

1H3-E

D513

1H3-E

D502

1N4005-EIC

D511

1F5-

E

D505

1N4005-EIC

C516

0.00

3325

0VKX

C515

0.01

400V

PP

C514

470P500V B

C540

0.0068 B C503

0.1 B

C508

680P

CH

C502

0.22

275V

ECQU

L

C513

47P

2KV

SL

C505

100P

2KV

R

C517

C522

C506

2.2

50V

KA_P

C509

1050

VYK

_P

R503

1.5M

1/2W

R513

3.9K

R518

3.3K

+-1%

R516 10

R515

1K

R514

470 1/4W

R505

22 1/4W

R512

100K

1/2W

R517

1.2K

+-1%

R504

680K

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTNOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIM



B501

W4B

RH3.

5X6X

1.0X

2

2.3904.69

1.6A 250V{F501}

1.6A 250V{F501}

NC

NC

0

0

0

0

0

0

130

130

130

-22.5

-22.5

NN

L

GNDOUT IN

9.90

3.9 10.9

0

0

0

NCDDOC

P

VCC

GND

FB/O

LPST

ARTU

P

17.5 3.90.1

130 130 130

0

0 NC

CHASSIS GND

(POWER PCB)POWER SCHEMATIC

IC504PS2561AL1-1-V(W)

PHOTO COUPLER IC

59DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

IS NON POLAR ONE.THE ALUMI ELECTROLYTIC CAPACITOR MARKED NPTHE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:

R529_1

220 1W

R510_1

2.7 1W

IC501KIA431A-AT

OLTAGE CTL IC

12

R511

68 1/4W

Q506KTA1504S_Y_RTK

PROTECT

IC503PQ070XF01SZH

24

+6V REG (DVD MOTOR) IC

1 2 3 4

C520

100

50V

YK_P

CD73012H0C3002

FFC(1.25mm pitch)

CD502E82G3301

CORD CONNECTOR

CD6003TD-OR0201R

TM601076E0PP031 BT601

R6P(AR)XICI

UM-4

C521

1000

16V

ZL_P

C523

470

25V

YK_P

C526

470

6.3V

YK_P

CP502A2001WV2-16P

1

10111213141516

23456789

D533

MTZJ2.2B

D531

MTZ

J27B

D517

MTZ

J2.2

B

D523

MTZ

J3.6

B

D528

MTZ

J5.1

B

D535

MTZ

J5.1

B

D536

MTZ

J3.0

B

CP503IMSA-9604S-12C

A/V for 21PIN

1

101112

23456789

L503

22uHTSL0808

L505

22uH


Q502 KTC3209-Y(GP)-28V P.CON SW

Q501KTC3875S_Y_RTK

PROTECT

Q515 2SD1835S/T-AAP.CON+5V REG

Q512KTC3875S_Y_RTKFL+ CTL

Q509KTC3875S_Y_RTK

REG+12V CTL

Q511KTC3875S_Y_RTK

REG+12V CTL

Q503KTA1504S_Y_RTK

-28V CTL

Q504KTA1281-Y(GP)

FL+ P.CON SW

Q513KTA1504S_Y_RTK

FL+ CTL

Q510 KTA1281-Y(GP)P.CON+12V SW

D521

1SS1

33

D520

1SS1

33

D522

1SS1

33

D534

1SS133

D515

1S40-E

D519

1F5-E

D527

SR240-F

D510

SF26-F

D512

1H3-E

Q505KRC102SRTK

P.CON SW

C524

100P

CH

C501

0.01

B

C540

0.0068 B C503

0.1 B

C541

0.01 B

C528

2.2

50V

KA_P

C536

220

6.3V

YK_P

C531 10

016

VYK

_P

C519 22

35V

YK_P

C517 22

025

V YK_P

C527

100

10V

YK_P

C522 10

006.

3V ZL_P

C538

220

6.3V

YK_P

C535 33

016

V YK_P

R536

10K

R537

1K

R539

4.7K

R528

22K 1/4W

R519

3.3K

R545

22K +-1%

R524

1K1/

4W

R546

3.3K +-1%

R548

1K

R531

10K

3

R543

4.7K

+-1%

R541

5.6K

+-1%

R542

470

+-1%

R526

6.8K

+-1%

R518

3.3K

+-1%

R523

22K

R527

100

R506

100

R538

22K

R516 10

R515

K

R509 1K

R530 56

01/

4WR5

44

10K

R514

470 1/4W

R540

680

R517

1.2K

+-1%

R525

100

R547

22

R534

100 1/4W

W81

9

W817

W825

TO CHANGE WITHOUT NOTICE.S THE LATEST AT THE TIME

AL TESTERT WAS

B502HCB2012K-600T25

(W023)

GND

AT+3.3VP.CON+12VAMP_A_OUT_RAMP_A_OUT_LG/Y_VIDEOB/U_VIDEOR/V_VIDEOCVBS/C_VIDEOP-H/I-L_RGB-HASP/FSA_GND

G/Y_VIDEO

B/U_VIDEO

R/V_VIDEOP-H/I-L_RGB-H

ASP/FSCVBS/C_VIDEO

AMP_A_OUT_L

AMP_A_OUT_R

2.390

28.428.4

27.8

0

02.8

NC

ACCESSORY

TO 21PIN/D-TERMINAL/DIGITAL

FROM/TO VIDEO JACK

GNDAUDIO L

GNDAUDIO R

RGB-H

CVBSFS

G

B

RGND

GND

(CP7301)

6.80.6

0

(CP4003)

0

9.9

0

3.2

03.2

P.CON+12V

P.CON+5V

FL DC-FL DC+

GND

GNDAT+12V for MUTE

P.CON+6V

-28V

GND(M)

GND(D)

AT+3.3VAT+3.3V

P.ON-H(STBY L)

GNDUT IN

19.0

0.60

5.8

5.17.0

19.719.0

20.7

GND(USB)USB+5V

IN GNDOUT ADJ

7.0 5.9 0 1.2

20.8

21.521.6

4.5

12.35.0

4.5

12.95.1

12.612.3

12.9

(POWER PCB)CHEMATIC DIAGRAM

DPG017PCB240

FROM/TO POWER PORT

60 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

10.9 POWER PCB ASSY(2/2)

POWER PCB ASSY (2/2)(A2L103A240)

K

DV

D810

3

MTZ

J6.8

B

D810

5

MTZ

J6.8

B

D810

4

MTZ

J6.8

B

CAUTION: DIGITAL T

Q8101KTC3875S_Y_RTK

21PIN CTL INQ8102

KTA1504S_Y_RTK

21PIN CTL DRV

D810

1

1SS1

33

Q8104KRC104SRTK

DVD_RGB_H_OUT

C810

1

0.00

1B

C810

6

0.00

1B

C810

5

0.1

B

C

6.3V

C

6.3V

C8115

10006.3V YK_P

C8113

4706.3V YK_P

R812

0

11/

4W

R8105

390 1/4WR8101

4.7K

R810

8

8.2K

R810

4

6.8K R8

103

470

1/4W

R810

2

56K




AT+3.3V

P.CON+12V

P-H/I-L_RGB-H

ASP/FS

AMP_A_OUT_R

AMP_A_OUT_L

G/Y_VIDEO

B/U_VIDEO

R/V_VIDEO

CVBS/C_VIDEO

A_GND

0

03.2

03.2

3.3

11.4

0

0

11.412.1

12.1

(POWER PCB21PIN/D-TERMINAL/DIGITAL

FROM POWER

61DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

* The parts except mark cannot be changed. On that occasion, replace whole Assy.

5

6

1

2

3

4

Q8105KRA102SRTK

DVD_RGB_H_OUT

J8101MRC-021V-07_A

21PIN CONNECTOR

1

10

11

12

13

14

15

16

17

18

19

220

213

4

5

6

7

8

9

L810110uH 0405

CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR

Q8104C104SRTK

D_RGB_H_OUT

C811

6

33P

CH

C810

7

0.00

1B

C811

1

0.00

1B

C8112

10006.3V YK_P

C8114

4706.3V YK_P

C8115

10006.3V YK_P

C8113

4706.3V YK_P

R8109

68 1/10W +-1%

R8114

220 1/10W+-1%R8115

220 1/10W+-1%

R8110

68 1/10W+-1%

R8112

68 1/10W+-1%

R8113

75 1/10W+-1%

R8111

68 1/10W+-1%

21PIN_R

21PIN_L

21PIN_CTL

G/Y_VIDEO_OUT

B/U_VIDEO_OUT

R/V_VIDEO_OUT

BLANKING_OUT

CVBS_VIDEO_OUT

NC

NC

NC

NC

NC

03.2

3.3

POWER PCB)/DIGITAL SCHEMATIC DIAGRAM

DPG017PCB240

62 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

10.10 WAVEFORMS

AUDIO JACK

POWER PCB ASSYDVD MT PCB ASSY

Note : The encircled numbers denote measuring point in the schematic diagram.

MPEG/MICON/DSP 21PIN/D-TERMINAL/DIGITAL

1 1

IC4001-pin66 (SDCLK)V:0.5V/div. H:2ns/div.

IC4001-pin93 (SPDIF)V:1.0V/div. H:200ns/div.

2 2

3 3

4 4

5 5

6

7

8

9

10

J8001-pin2 (Coaxial Out)V:500mV/div. H:200ns/div.

J8003-pin3 (Lch_Out)

IC4001-pin9 (XTALI)

J8003-pin2 (Rch_Out)

63DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

OPERATION PCB ASSY

POWER PCB ASSY

1

DISPLAY

6

64 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

11. PCB CONNECTION DIAGRAMNOTE FOR PCB DIAGRAMS :1. Part numbers in PCB diagrams match those in the schematic diagrams.2. A comparison between the main parts of PCB and schematic diagrams is shown below.

3. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram.4. View point of PCB diagrams.Symbol In PCB

DiagramsSymbol In SchematicDiagrams

Part Name

B C E

D

D

G

G

S

S

B C E

B C E

D G S

B C E B C E

B C E

Transistor

Transistorwith resistor

Field effecttransistor

Resistor array

3-terminalregulator

CapacitorConnector

P.C.Board Chip Part

SIDE A

SIDE B

65DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

11.1 DVD MT PCB ASSY

SIDE A SIDE A

DVD MT PCB ASSY

1 33

6597

DMG099A

X4001

J7302

Q8014

Q8019

Q8020

Q8021

Q8005

R8057

R8069

R8066

R8061 R8049

R8048R8063

R8067

R8056

R8073

R8082

R8074

R8077

R8081R

8078

R8080

R8079

R8083R8085

R8037

R8084

R8039

R8040

R8038

R8035

R8036

C8066

C8073

C8070

W840

C8042

C8056

C8057

C8058

C8067

C8069

C8072

C8077

C8078

J8001

CP7301

C7316

C7317

C7318

C7319

R7319

R7320

R7321

B7304

B7305

B4002

B8004C8036 R

7302

IC4003

IC7301 R4059

R4060

R4061

R4062

C7311

R7307

C7305

C7306

C7307C7308

D7306D7305

R7301

IC8003

J8003

R4035C7303

C8051

C8053Q8018

Q8013

C7309

C7310

R7305

D7312

D7310

D7311

C8038

L7301

Q4001

C7315

IC7302

Q7302

IC4001

R2316

W805

W806

C2307

C2312

C2311

R2310W802R

2313R

2312

R2327

R2318

R2317

R2325

C2306

IC2301

R4011

C4116

C4112

IC4006C

4100

C4099C4098

C4096

C4095

B4001

R4013

C2301

CP2302

C2321

C2320

R4012

R2309

R2306R2307

R2328

R2319

Q2303

Q2304

Q2301 Q2305

Q2302

C4052

IC4005

R4066

C4049

NR

4002

R4027

C4050

CP2303

CP4003

IC4009

C4137

C4141

R4063

R4073

R4072

C4091

C4104

IC4004

R4040

R4044

W810

R4053R4054

C4078

R4033

B4008

C4029 C4002

R4039

W808

R4024 R4025

C4090

C4089

R4014

R4015 R4016

B4007

W829

R4018

R4019

C4006

R4031

C4039C

4044

L4001

C4142

C4134

W844

W809D4003

W832W839

C4080

CP2301

W826

R4008

C4010

C2303

W816

W817

C4072C4012

NR2301

R4074

C2304

C4047

C4046

C2302

R2344

C2323

C8059

R7308

R7306

C7312

R8059

R8060

C7304

C7313

C4056

R8076

R8051

R8014

C2322

R2342

C4086

R4022C4011

C4062

C4101

C4102

C4005

C4007

C4140

C4077

R4002

C2305

R2311

R4017

R2308

C4088

C4048

C4051

R4046

CP

4002

C4132

CP

4004

Q7301

D4002

R4045

R2326

R7316

R7315

R7318

R7317

Q7305B7301

R4058

W820

R4075

66 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

SIDE B SIDE B

DVD MT PCB ASSY

DMG099A

C80

74

W833

W834

R80

70

W88

9

B73

02

R2341

R2343

C40

93

W821

W822

R40

26

R40

20

C40

01

C40

08

R4001

W845

R40

05

R40

76

R40

37R

4036

R4032

R4038

R4030 R4029

R40

43

IC4007

R40

21

R40

10

Q4003

R40

07

R40

42R

4034

W813C40

03C

4030

W81

2

C40

37C40

33C

4036

C40

25

C40

58

W836

C40

38

C41

14C

4122

C41

33 C41

35

R40

48

D40

05

W831

C40

19

C40

20

C40

63 C40

13C

4014

D2301

D2302

W81

5

Q2306

W83

0

W81

9C

4045

B40

12

C40

23

B40

10

C40

64

C40

74

C40

71 C40

73C

4060

C40

57

W82

5W

842

R40

65

C40

66

W849

W85

0

C40

76

C40

59

C40

55

W81

4

67DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

11.2 OPERATION PCB ASSY

SIDE A SIDE B

OP

ER

AT

ION

PC

B A

SS

Y

OP

ER

AT

ION

PC

B A

SS

Y

SW

667

SW

665

SW

664

SW

662

SW

660

SW

663

W02

1

SW

666

D65

9

D657

D65

8

SW

668

D656

D655

D654

D652

W017

SW

661

SW

658

SW

659

SW

652

SW

655

SW

656

W00

1

D65

1

SW

657

SW

654

W005W004

W016

W013

W012

W014

D665

W018

W02

2

C67

4

C65

3

R666

W006

W011

W00

2

W019W020

V65

1

CP

601

CP

605

W007

CP6

03

CP604

W02

3

CP602

OS

651

SW

653

W80

4

W00

3

D669

DE

G14

9A

DE

G15

0A

GA30

C5

GA30

C5

23

34

1

12

C651

R657C611R655

R658

C610 R656

IC651

C654

B601

C675

R662

R654

C605

C604

C676

C658

C601

C608

W803

B602

W806

C613

DE

G149A

DE

G150A

68 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

11.3 POWER PCB ASSY

SIDE A SIDE A

POWER PCB ASSY

J8101

J501

FH502FH501 F501

L501

C502

R503

D505

D502

D503

D506

T501

IC502D511

W006

W003

D513

C514

IC504

C509C50

5

R512

C506

D508

C513

R507

W002

B501

SH501

R505

C516

IC501D515

D527

C517

C522

C520

D512

D510C521

C523

IC503

C531

W013

W012

Q515

C535

W021W

817

C527

R511

D517

D534

W022

W007

W017

Q502C528

R528

R530

W008

C538

L503

CP503

D8104L8101 D8101

R8103

R8105

C8112

D8103

C8113

D8105

C8114

W023

C8115

R8120

W018

C536

L505

W015

D528

C526

W014

W011

W019

W009

D533

R534

W005

W010

D536 D535D531 C519

D523

D520

D522

D521

R514

CP502

W004

W819

W001

C515

D519

Q504

Q510

R510_1

R529_1

R502_1

D509

C511_2

R524

W825

DPG017A

RISK OFFIRE- REPLACE AS MARKED .

GA30C5

69DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

SIDE B SIDE B

POWER PCB ASSY

R504

C508

Q509Q511

R540

R543

R542

R541

R526

R509

R525

R547

C501

R519

Q505

R545

R8114

C8111

R8115

C8107

R8111

R8102

Q8102 Q8101

R8104

R8108

R8110

R8112

R8101

R8113C

8116

Q8105

Q8104

C8101

C8106

R536

Q503

R531

R548

R537

Q513

R544

Q512

R515

C540

C503

R513

R518

R516

R517R

539

Q506

R506

R538

R527

Q501

R523

C541

C8105

B502

R8109

R546

C524

DPG017A

70 DV-310-S

1 2 3 4

A

B

C

D

E

F

1 2 3 4

11.4 LOADING MOTOR and SW

SIDE A SIDE B

SW

LOADING MOTOR (INSERTED PARTS)

LOADING MOTOR (CHIP MOUNTED PARTS)

DED021A

DED021A

DED020A

SW

2 CD

2301

M2602 M2601

SW1

CD2302M2603

15

WH

BR

BRWH

YE

GR

71DV-310-S

5 6 7 8

5 6 7 8

A

B

C

D

E

F

12. PCB PARTS LISTParts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.The mark found on some component parts indicates the importance of the safety factor of the part.Therefore, when replacing, be sure to use parts of identical designation.When ordering resistors, first convert resistance values into code form as shown in the following examples.Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%).

Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).

5 6 14 7 3

R 5 01 R 0

5 6 2 1

NOTES:

560 Ω47k Ω0.5 Ω1 Ω

RD1/4PU JRD1/4PU JRN2H KRS1P K

56 x 10 1

47 x 10 3

R501R0

561473

5.62k Ω RN1/4PC F562 x 10 1 5621

Meaning of the figures and others in the parentheses in the parts list.Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board.IC 301 (A, 91, 111) IC NJM2068V


LIST OF ASSEMBLIES1..DVD MT PCB ASSY A2L103A130

1..OPERATION PCB ASSY(WYXZT5)* A2L103A270

1..OPERATION PCB ASSY(WSXZT5)* A2L109A270

> 1..POWER PCB ASSY A2L103A240

(*) A2L103A270 and A2L109A270 have same service parts.But they are NOT COMPATIBLE.


DVD MT PCB ASSYSEMICONDUCTORS

IC 2301 IC AM5766 I1UFV5766SIC 4001 IC MT1389FE/L-L IC8K0389L0IC 4003 IC R3112N291A-TR-FA IE1F0291A0IC 4004 IC AT26DF161-SU S2L101AF01IC 4005 IC M12L64164A-7TG IF9J0164AG

IC 4006 IC LD1117AL-ADJ-AA3-A-R I1YF9117A0IC 4007 IC R5523N001B-TR-F I1ZF0N0010IC 4009 IC BA00BC0WFP-E2 I07F0C0WF0IC 7301 IC LA73054-TLM-E I03FG30540IC 7302 IC SN74CBT3257PWR I5CJ032570

IC 8003 IC RC4580IDR I04J045800

OTHERSJ 7302 RCA JACK 060R451013J 8001 RCA JACK 060R401122J 8003 RCA JACK 060R451012X 4001 CRYSTAL (27MHz) 100GT02720

OPERATION PCB ASSYSEMICONDUCTORS

IC 651 IC PT6315 IF4K063150

SWITCHESSW 652-667 SWITCH TACT 0504R01T38

OTHERSCP 602 CONNECTOR PCB SIDE 06G5AA1002V 651 TUBE FLUORESCENT 096F80R401

OS 651 REMOTE RECEIVER 077Q040004

POWER PCB ASSYRESISTORS> R 511 R,FUSE 68 OHM 1/4W R65584680J

OTHERSJ 8101 SOCKET, 21PIN 063D100050


DV-310-Kradio-hobby.org/uploads/schemes2/1002-DVD/PIONEER DV-310-S.pdf · a soldering iron. If you...

Documents

Transcript of DV-310-Kradio-hobby.org/uploads/schemes2/1002-DVD/PIONEER DV-310-S.pdf · a soldering iron. If you...