Cornerstone VoiceSpain CSV04.1 IS To CSV04.1 IS1

Upgrade CAPVersion 1.0

Change Application Procedure

MNSxxxx

December 17, 1998

1

Publication HistoryDecember 17, 1998 - Revision 1.0: Initial release.

2

Contents

ABOUT THIS DOCUMENT 4

Purpose 4

Audience 4

Executive summary 4

Terms and symbols 4

CHAPTER 1: INTRODUCTION 5

Field of application 5

Effects of service 5

Requirements 5

Time Requirement 5

Technical Expertise Requirement 5

Document Sequence 5

CHAPTER 2: 6

HDT UPGRADE 6

Procedure 2-1 6

Transferring the MVP load from tape to OPC 6

CHAPTER 3: MODEM SHELF UPGRADE 8

Procedure 3-1 8

Transferring the MVP load from OPC to MSC 8

APPENDIX A: SOFTWARE BASELINE 9

3

4

About This DocumentPurposeThis CAP is being published for the purpose of upgrading a Spain system with a CSV04.1 IS software release to a CSV04.1 IS1 software release.

Comments regarding this procedure may be sent to Arris Interactive at the following address:

Arris InteractiveAttention Mitch Matteau, Director Customer OperationsCornerstone Voice Customer Service3871 Lakefield Dr., Suite 300Suwanee, GA 30024-1242

Or email to: mitch.matteau@arris-i.com

AudienceThis document is intended for system engineers and those responsible for software/hardware upgrades. Users of this document should have experience with Cornerstone Voice command interfaces, including an understanding of basic UNIX commands.

Executive summaryThis load release contains the new firmware load CVPMVL16AQ01 for the MVP. This new firmware load is the only update from CS04.1 IS to CSV04.1 IS1.

Terms and symbolsDetailed below are some useful definitions of terms and symbols used throughout this document.

The terms “NE” (Network Element) and “HDT” (Host Digital Terminal) are used interchangeably throughout this document. Both refer to one standard Cornerstone Voice modem shelf/ABM shelf pair. The terms “NE” and “HDT” are not to be confused with “OPC” (Operations Controller), which refers to the Unix-based control unit which may or may not reside on a given Cornerstone Voice ABM shelf.

The word “move” when used in the appropriate context (for example, in a procedure step involving the OPC or NE user interface) indicates that you should use the left, right, up, or down arrow keys to access the portion of the Character Mode Terminal (CMT) VT-100 screen required by the step being performed.

The word “type” indicates that all characters in a specified command should be entered.

The word “press” indicates that all characters in the specified key-stroke should be pressed in a certain order (for example, {Ctrl_T /} requires you to press the Ctrl and T keys simultaneously, and then press the / key.

The symbols ø or <return> indicate that you should press the carriage return key on your terminal’s keyboard.

The phrase “tab to” indicates that you should press the tab key on your terminal keyboard as many times as required to access the appropriate area of the CMT screen required by the step being performed.

Warning and Caution notes will appear throughout the document to advise you of consequences or results of certain actions that should be performed or avoided.

5

Chapter 1:Introduction

Field of applicationThis CAP contains the procedures necessary in order to upgrade a Spain Host Digital Terminal (HDT) with a CSV04.1 IS release loads to CSV04.1 IS1 release loads.

Effects of serviceIf there are no MVPs deployed in the network served by the HDT, there should not be any service interruption during the upgrade. Therefore the upgrade can be perform outside the maintenance window.

RequirementsUsing checkvp pec command verify that there are no MVPs deployed in the network served by the HDT.

Time RequirementThis upgrade can be performed within about 15 minutes or less per HDT.

Technical Expertise RequirementThis CAP assumes that the person performing the upgrade is familiar with the Cornerstone system and its user interfaces, including basic UNIX commands. If the person cannot successfully complete this CAP, contact your next level of Cornerstone support.

Document SequenceFollow the steps in the following chapters in the order shown, using the timeline(s) presented below as a scheduling and completion guide. Read each procedure from start to finish before performing it. See Appendix A for information on the hardware and/or software affected by the CAP.

6

Surely we should do a backup of the existing load before we start? It doesn’t mention this…….Chris

Chapter 2:HDT Upgrade Procedure 2-1Transferring the MVP load from tape to OPC

All steps, including those involving the backup OPC, should be performed via a login session to the primary OPC.

Step Action and response Est. Time

[ ] 1. Insert the CSV04.1 IS1 software upgrade tape in the Primary OPC tape drive.

1 minute

[ ] 2. Open the NE Software Delivery Mngr tool and select the Primary OPC. Then query the loads on tape. Select the MVP load CVPMVL16AQ01 and transfer it to the OPC. Then select CVSWLD file and transfer it to the OPC.

2 minutes

[ ] 3. If a backup OPC exists, perform step 2 again but this time on the backup OPC..

Note: You will not be able to verify the presence of the loads on the Backup OPC because it is inactive.

2 minutes

[ ] 4. Once the transfer is complete remove the tape from the OPC tape drive. Verify the presence of the CSV load CVPMVL16AQ01 and CVSWLD file on the disk by entering the following commands at the OPC prompt:

opc>cd /users/VFS/users/csvopc>ll

CVPMVL16AQ01 and CVSWLD should appear in the list.

1 minute

[ ] 5. Display the contents of the CVSWLD.load file by entering the following command:

opc>more CVSWLD.loadThe following information should be displayed:

NTBN20AA CMSINL16AO00NTBN20AB CMSINL16AO00NTBN19AA CDMNAL16BC01NTBN19CA CDMNAL16BC01

1 minute

7

NTBN52BA CVPNAL16BI01NTBN62AA CVPNAL16BI01NTBN52DA CVPPHL16BI01NTBN65BA CVPMVL16AQ01NTBN65BB CVPMVL16AQ01NTBN65AA CVPMVL16AQ01NTBN65AB CVPMVL16AQ01NTBN52GA CVPSHL16BI01NTBN62GA CVPSHL16BI01NTBN52KA CVPSHL16BI01NTBN52HA CVPMHL16BI01NTBN62HA CVPMHL16BI01NTBN52IA CVPMHL16BI01NTBN62IA CVPMHL16BI01NTBN52RA CVPMHL16BI01NTBN52PA CVPMHL16BI01NTBN65PA CVPMVL16AQ01NTBN65QA CVPMVL16AQ01

8

Chapter 3:Modem Shelf Upgrade

Procedure 3-1Transferring the MVP load from OPC to MSCNote: This procedure is to be repeated for each HDT that is scheduled for upgrade.

Step Action and response Est. Time

[ ] 1. Login to the NE. Then go to the Cornerstone CI cvloader. Display the current modem shelf default loads.

>cornerstone;cvloader>listdefaults

1 minute

[ ] 2. Transfer the new modem shelf load lineup from the OPC to the MSC by entering the following command.

>syncdefaultsDisplay the current modem shelf default loads.

>listdefaults

This time the new MVP load CVPMVL16AQ01 should appear on the list.

1 minute

9

Appendix A:Software BaselineTable A-1 lists the software modules upgraded by the Spain CSV04.1 IS1 release.

Table A-1 Software modules upgraded from CSV04.1 IS to CSV04.1 IS1.

CSV04.1 IS CSV04.1 IS1

OPC: ACNL14CD OPC: ACNL14CD

APU: CSVIL16BO01 APU: CSVIL16BO01

HMU: IHMUL15AM HMU: IHMUL15AM

TAC: TACL15AB TAC: TACL15AB

2-line Model 4 VP: NTBN62IA

CVPMHL16BI 2-line Model 4 VP: NTBN62IA

CVPMHL16BI

6-line MVP: NTBN65AB

CVPMVL16AP01 6-line MVP: NTBN65AB

CVPMVL16AQ01

12-line MVP: NTBN65BB

CVPMVL16AP01 12-line MVP: NTBN65BB

CVPMVL16AP01

M2DMC: NTBN19CA

CDMNAL16BC01 M2DMC: NTBN19CA

CDMNAL16BC01

MSC: NTBN20AA/AB

CMSINL16AO00 MSC: NTBN20AA/AB

CMSINL16AO00

APU Firmware: APCFTL16AK0 APU Firmware: APCFTL16AK0

CSV default: CVSWLD CSV default: CVSWLD

SM: CSM11AQ02 SM: CSM11AQ02

10

Cornerstone VoiceSpain CSV04.1 IS To CSV04.1 IS1 Upgrade CAPCAP Procedure

1997 Arris Interactive

All rights reserved

All information contained in this document is subject to change without notice. Arris Interactive reserves the right to make changes to equipment design or program components, as progress in engineering, manufacturing methods, or other circumstances may warrant.

Cornerstone is a trademark of Arris Interactive.

MNSxxxx

Printed in USA.