CC(STi) Cruise Control STi
Transcript of CC(STi) Cruise Control STi
-
7/25/2019 CC(STi) Cruise Control STi
1/8
CRUISE CONTROL SYSTEM
(STi)
-
7/25/2019 CC(STi) Cruise Control STi
2/8CC(STi)-2
CRUISE CONTROL SYSTEMGENERAL DESCRIPTION
1. General Description
A: COMPONENT
B: CAUTION Before disassembling or reassembling parts, al-ways disconnect the battery ground cable. Whenrepairing the radio, control module and other partswith memory functions, make note of the memorybefore disconnecting the battery ground cable. All
memory will be erased. Reassemble parts in the reverse order of disas-sembly unless otherwise indicated. Adjust parts to specifications specified in thismanual. Connect the connectors and hoses securely dur-ing reassembly. After reassembly, ensure functional parts oper-ate properly.
C: PREPARATION TOOL
(1) Engine control module (ECM) (3) Cruise indicator light & cruise set
indicator light
(4) Stop light and brake switch
(2) Cruise control command switch
(with built-in main switch)
(5) Clutch switch
CC-00196
(2)
(4)(5)
(1)
(3)
TOOL NAME REMARKS
Circuit Tester Used for measuring resis-tance and voltage.
-
7/25/2019 CC(STi) Cruise Control STi
3/8CC(STi)-3
CRUISE CONTROL SYSTEMCRUISE CONTROL MODULE
2. Cruise Control Module
A: NOTEEngine Control Module (ECM) controls cruise con-trol system.
B: REMOVAL
C: INSTALLATION
-
7/25/2019 CC(STi) Cruise Control STi
4/8CC(STi)-4
CRUISE CONTROL SYSTEMCRUISE CONTROL COMMAND SWITCH
3. Cruise Control CommandSwitch
A: REMOVAL
WARNING:Before servicing, be sure to read the notes inthe AB section for proper handling of the driv-er's airbag module.
1) Set the front wheels in straight ahead position.2) Turn the ignition switch to OFF.3) Disconnect the ground cable from battery andwait for at least 20 seconds before starting work.4) Using the TORX BIT T30 (Tamper resistanttype), loosen the two TORX bolts which securedriver's airbag module.
5) Disconnect the airbag module connector onback of airbag module.6) Remove the steering wheel. 7) Remove four screws, and then remove the lowercover from steering wheel.
8) Remove the screw, and then remove the cruisecontrol command switch from lower cover.
B: INSTALLATIONInstall in the reverse order of removal.
C: INSPECTIONMeasure the cruise control command switch resis-tance.
If NG, replace the cruise control command switch.
(1) TORXBIT T30
CC-00018
(1)
CC-00181
Switch Position Terminal No. Standard value
CANCEL ON 1 (+) and 2 () Less than 1 ON 1 (+) and 3 () Less than 1
SET/COASTOFF 1 and 3 More than 1 M
ON 1 and 3 Less than 1
RESUME/
ACCEL
OFF 1 and 2 More than 1 M
ON 1 and 2 Less than 1
MAIN
SWITCH
OFF 5 and 4 More than 1 M
ON 5 and 4 Less than 1 M
CC-00182
CC-00184
3 1245
-
7/25/2019 CC(STi) Cruise Control STi
5/8CC(STi)-5
CRUISE CONTROL SYSTEMSTOP LIGHT AND BRAKE SWITCH
4. Stop Light and Brake Switch
A: REMOVAL1) Disconnect the ground cable from battery.2) Disconnect the connector from stop light andbrake switch, and then remove the switch.
B: INSTALLATIONInstall in the reverse order of removal.
C: INSPECTIONMeasure the brake switch (A) and stop light switch(B) resistance.
If NG, replace the stop light and brake switch.
Switch Pedal Terminal No. Standard value
BrakeReleased 1 and 4 Less than 1
Depressed 1 and 4 More than 1 M
Stop lightReleased 2 and 3 More than 1 M
Depressed 2 and 3 Less than 1
CC-00022
12
34
(A)
(B)
321 4
-
7/25/2019 CC(STi) Cruise Control STi
6/8CC(STi)-6
CRUISE CONTROL SYSTEMCLUTCH SWITCH
5. Clutch Switch
A: REMOVAL1) Disconnect the ground cable from battery.2) Disconnect the connector from clutch switch,and then remove the switch.
B: INSTALLATIONInstall in the reverse order of removal.
C: INSPECTIONMeasure the clutch switch resistance.
If NG, replace the clutch switch.
Switch Pedal Terminal No. Standard value
ClutchReleased 1 and 2 Less than 1
Depressed 1 and 2 More than 1 M
CC-00023
-
7/25/2019 CC(STi) Cruise Control STi
7/8CC(STi)-7
CRUISE CONTROL SYSTEM
NEUTRAL POSITION SWITCH
6. Neutral Position Switch
A: REMOVAL
B: INSTALLATION
C: INSPECTION
-
7/25/2019 CC(STi) Cruise Control STi
8/8CC(STi)-8
CRUISE CONTROL SYSTEM
NEUTRAL POSITION SWITCH