CADASTRAL STUDIES (MGU1014 /...
Transcript of CADASTRAL STUDIES (MGU1014 /...
CADASTRAL STUDIES(MGU1014 / MGHU1514)
WEEK 12&13-NEW CADASTRAL SYSTEM IN MALAYSIA
SR DR. TAN LIAT CHOON07-5530844
016-4975551
1
OUTLINE
• Applied eCadastre
2
APPLIED eCADASTRE
3
UPPER BOUND IN LSADuplicate Value For The Same Line
4
Line 4-1 bearing residual shown possible error?
5
THERE ARE 2 RECORDS FOR LINE 4-1? One for traverse (CODE = 12) and another for PO (CODE = 26)?
6
After deleting the line 4-1 for PO, result LOWER BOUND.
7
UPPER BOUND IN LSA“M” correction is not applied in
ASCII
8
Upper Bound And Failed
• In principle the survey is drop.
• Might be the survey on the ground or the 16 ASCIIoutput.– Meaning to say the survey and 16 ASCII output are not
TALLY.
• Suppose the survey and the 16 ASCII output are the same.
• Always check the chi-square result, bearing and distanceresidual for troubleshooting.
9
• Noticed that the COR file is NULL. COR file cannot be NULL.
10
Only those with √ can be NULL
11
• COR file is needed if doing Sun Observation.
• “M” correction is crucial but the “C” correction is ignoredby the system.
• The system will relate the “M” in the COR file to thefieldbook FBK data.
12
Finding
• Apply one point (Stn 6) as fix point in LSA
13
UPPER BOUND IN LSA16 ASCII and survey value not tally
14
Distance residual shown line 12-13 having the highest standard residual. This could be the line.
Check the FBK data.15
12-13 in comp sheet is 228.4310. But in FBK is 48.4310? 16
Once the value for 12-13 in FBK is wrong, the output to DAT file to be used for Least Square Adjustment
also is wrong.
17
Alter the line 12-13 in FBK to 228.4310. Same as in the comp sheet.
18
Result LOWER BOUND
19
UPPER BOUND IN LSADrop in survey
20
21
22
• Misclosure for 12-35 using 12 – 7 – 6 – 35 route :
• Calculate bearing and ditance for 12-35
23
• Misclosure for 12-35 using 12-13-14-15-16-17-18-19-20-21-22-11-23-25-26-27-28-29-30-31-32-33-34-35 route:
• Calculated bearing and distance for 12-35
24
Traverse 12-35 Bearing Distance
Observe (FBK) 162.1349 48.084
Short route 162.1351 (+0.0002) 48.315 (+0.231)
Long route 162.1400 (+0.0011) 48.318 (+0.234)
• Comparison Bearing and Distance
* Short route : 12 – 7 – 6 – 35* Long route : 12-13-14-15-16-17-18-19-20-21-22-11-23-25-26-27-28-29-30-31-32-33-34-35
25
• Exclude 12-35 in Star*Net LSA
26
• Include 12-35 in Star*Net LSA
27
ONLINE SURVEY CODING WRONG IN FBK
28
Online Remark in FBK
Original Data
Amended Data
Online parent is wrong, suppose in 39 – 47, but no 39-49.
29
eTSM Online procedure
23
4 5
Traverse Line Code Line Code Description
2 – 3 12 Traverse
2 – 4 13 On-line
2 – 5 13 On-line
4 – 5 23 On-line Check
2 – 3 13 On-line
5 – 3 23 On-line Check
Online Info is to store into .FBK and .COO 30
PROBLEM ZIPFILE
31
So many levels in the zip file? The folder structure is wrong.
32
The correct folder structure when view in winzip.
33
PROBLEM FOLDER STRUCTUREESPECIALLY FOR CRM
34
eVRSCAL AND NOT eVRASCAL
If static must provide us the following :
1.PVM_PUBLSEL2052_2010.html2.Core-RINEX/Virtual RINEX downloaded from JUPEM
35
MUST BE ONLY 1 POT AND 1 CRM FILE
36
37
TOO MANY POT AND CRM FILES
38
CRM office encountered problem to match RAW data to which point?
The FILENAME and FILENO tab spacing are wrong.
Yours
The correct format
39
Yours
The correct format
The FILENAME, FILENO and STNID tab spacing are wrong.
40
Yours
The correct format
MARK_DESC is referring to actuall mark on the ground and not GPS as people always wrongly coded. It is either PAIP BESI BERKONKRIT or PEPAKU BERKONKRIT in accordance to KPUP6/2009
41
Yours
STN_STATUS for FULL STATIC is “20” and for RTK is “31”
42
Yours
The correct format
Where is the data for STDERREAST and STDERRNORTH? They are COMPULSORY fields.
43
44
The eVRSCAL.html format is not as required.
45
The required eVRSCAL.html format for at least 3 pillars. No need to upload to SPAKLS like the EDM.
46
The RTGA.html format is not as required.
47
The required RTGA.html format.
48
The required PVM.html format if FULL STATIC.
49
Field Survey –CRM Criteria KPUP 6/2009 Pg36
50
Field Survey –CRM Criteria KPUP 6/2009 Pg36
51
Field Survey –CRM Criteria KPUP 6/2009 Pg38
EDM FILE
52
53
Registration (KPUP 6/2009 Pg11)
Correct - EDM
54
Wrong- EDM
Please delete the <filename>.edm. Leave only the one downloaded from SPAKLS
55
Sample EDM File From SPAKLS
56
Fail *.edm yang telah diluluskan oleh JUD hendaklah dimuatturun dan dihantar bersekali dengan 15 ASCII yang lain
Untuk muat turun fail *.edm, klik papar
57
JTB boleh muat turun fail yang telah diluluskan oleh JUDDi SPAK LS
58
This information will only appear if there is a sun observation SOB being made because the SurveyorName field is there. If no sun observation, the SurveyorName will not appearing because the FAH does not has the SurveyorName field.
59
LS WRONGLY EDIT THE CP
60
61
Click download button from the list of Certified Plan
Right click PA number and choose ‘save target as’.
62
Click Save button to save the file
63
AMALGAMATION/MINIMUM SURVEY
64
The Requirement
• Resurvey of lot (landed) / Amalgamation / MinimumSurvey– Lot must be in NDCDB– If no lot in NDCDB, can ask for the advise from
State’s JUPEM to update the area of survey– PO value is referring to NDCDB’s value
65
66
• FBK
• FAH
• ACS
• TPS
• COO
** NOTE :1. The 16 ASCII still need to be submitted. 2. The rest of the files other than those listed above can be NULL.3. Lots to be amalgamated must be in NDCDB before this process is done.4. PO value is taken from NDCDB/PA.5. FBK is NULLABLE.
67
Mandatory ASCII Needed
NDCDB LOT
NDCDB LOT
NDCDB LOT
Nilai Asal (PO)
PO POPO PO
1 32 4
8 67 5
1103110001234
NOTES:•Each PO line must overlap with existing NDCDB BDY, else won’t consider as amalgamation lot.•Amalgamation lot will not go through SUM.
Nilai Asal (PO)
Nilai Asal (PO)
Nilai Asal (PO)
Nila
iAsa
l(P
O)
Nila
iAsa
l(P
O)
68
Scenario : Amalgamation Lot (without survey)
SNR Job Cantuman Job
• Ensure all station in NDCDB STN Layer
• No SUM Checking
• To differentiate from Cantuman Job, not all BDY = PO
• All Station = Old Mark
• Counter Check with NDCDB Stn
• Ensure every PO line will exist in NDCDB BDY layer
• No SUM Checking
• To differentiate Cantuman Job from SNR Job based on the submitted data, need to include PO Line into FBK
• IF All FBK Line= PO, then = Cantuman Job
NDCDNDCDB LOT
1
NDCDNDCDB LOT
2
NEW_NEW_PDUK LOT
PO PO PO
PO
PO PO PO
POPO PO
NDCDNDCDB LOT
1
NDCDNDCDB LOT
2
SNR LOT
PO
PO PO
POPO PO
Dpi
Dpi
69
Checking Algorithm – To Determine SUM Checking is Necessary
NO Field Sample Value
1 FIleName PUBLJ
2 FileNo 2008_2010
3 StnFromNo
4 StnFromType
5 StnFromSerial
6 OccStnNo 2
7 OccStnType BKL
8 OccStnSerial
9 StnToNo 3
10 StnToType BKL
11 StnToSerial
12 CLFrom 0.0000
13 CRFrom 0.0000
14 CLTo 39.0210
15 CRTo 219.0210
16 AvgBearing 39.0210
17 VAToCL 90.0000
18 CaToCR 270.0000
19 SDToCL 71.849
20 SDToCR 71.849
21 HD 71.849
22 ObsDate 20100716
23 ObsTime 094957
24 LineCode 26
25 Remarks
26 ParentFrom
27 ParentTo
FBK ASCII
70
NO Field Sample Value
1 FIleName PUBLJ
2 FileNo 2008_2010
3 SurveyType 8
4 Negeri 01
5 Daerah 02
6 Mukim 08
7 Seksyen 000
8 Lot 193382
9 SurveyorIC 610911015245
10 StartDate 20100317
11 EndDate 20100716
12 InstNo 617442
13 Remarks
71
FAH ASCII
NO Field Sample Value
1 FIleName PUBLJ
2 FileNo 2008_2010
3 Negeri 01
4 Daerah 02
5 Mukim 08
6 Seksyen 000
7 Lot 193382
8 SKLArea 130.1
9 PUArea 130.1
10 SvyArea 130.064
11 Percentage 0.03
12 Misclosure 92819
72
ACS ASCII
L, 1234, 11, 03, 11, 000, 100.2
1, 2, 3, 4, 5, 6, 7, 8, 1
END
K, 1,P
North, East, MarkDesc, , , M
END
K, 5,P
North, East, MarkDesc, , , M
END
K, 8,P
North, East, MarkDesc, , , M
END
73
TPS ASCII
NO Field Sample Value
1 FIleName PUBLJ
2 FileNo 2008_2010
3 StnNo 2
4 MarkDesc BKL
5 Serial
6 North -50594.539
7 East 20109.985
8 Code 4
9 Remarks
74
Survey Station
UPLOADING AND DOWNLOADING FILES FROM JUPEM2U
75
The Summary
• Perform Survey On The Ground As Usual.
• Zip The File.
• Upload The 16ASCII Zipfile To Jupem2u.
• Download The Uploaded 16ASCII From JUPEM2U. It Will Be InThe Form Of Zipfile.
• Use Jupem ASCIIsigner To Sign The Files.
• Upload The Signed 16ASCII Zipfile To JUPEM2U.
• Click The File Checkbox And Send To JUPEM2U.
76
LS ePKI DIGITAL SIGNING TOOLS
77
SPAKLS Homepage
78
JUPEMAscii Signer v3.1 and LLSOFFLINESIGNER V4.2
79
JUPEM ASCIISigner v3.1
80
LLSOfflineSigner v4.2
81
CERTIFICATE INSTALLATION
82
DigiCert Certificates
1) Root Cert – class2root.cer
2) Intermediate Cert – digisignidbasic1.cer
3) Soft Cert – noIC.pfx
– Refer to Certificate Installation.pdf
83
JUPEM ASCII Signer v3.1
84
Click the icon to DOWNLOAD SURVEYED ASCII FOR ePKIand click SAVE. Make sure knowing where the file is saved?
85
Activate ASCII SIGNER, select the ZIPFILE and click OPEN
86
All the files shall be unzipped
87
Click ESIGN, select the certificate and click SIGNING. Then keying the password and click OK 88
Message states the files have been signed and the location of the signed ZIPFILE 89
After signed, the zipfile shall has an XMLDSIG.XML file. Upload to JUPEM2U and then SEND to JUPEM.
90
Assume files already signed and to start uploading process, click upload surveyed file button and send to TPU. 91
The ASCII SIGNER is v3.1. if not then please download from SPAKLS. To check the version, click ABTUS 92
LLSOfflineSigner v4.2
93
SIGN CP OFFLINESIGNING CP THROUGH LOCAL PC
94
Make Sure Certificate Is Installed
95
Print Unsigned PA
96
Click view file Ukur at selected file Ukur number97
Click download button from the list of Pelan Akui98
Right click PA number and choose ‘save target as’.99
Click Save button to save the file100
101
Please Refer to the Manual
Login back to JUPEM2U Application. Click view file Ukur at selected file Ukur number 102
To start the uploading process, click upload button.103
Upload PA file. Browse to CP that has been signed before.
104
Verification appear. Once success, click complete job button 105
Signing Done, click close this window. File automatically moved to TPU_PD 106
DELETING FILE
107
Deleting File With Prefix “J”
108
Deleting File With Prefix “P”
LS “RETURN” THE FILE TO TPU_TD AND ASKING FOR DELETING IN THE MINUTE 109
Deleting File With Prefix “P”
“SEND” – completed a task and need to forward the file
“RETURN” – return without attending to a task or QUERY file by JUPEM
110
LJT NOTIFICATION
111
From To When Notification To LS Claimed
1 TPU_ TD
LS Appove Temp File with Lot Number
Notice 1: LS Job – Application For Lot Number Approved
LJT and LS([email protected])
6 months period as in Regulation 100 Licensed Land Surveyor Regulation taking into effect
2 LS TPU_TD
LS Lodge Surveyed ASCII via J2U
Notice 2: LS Job – Final Survey Submission Successful
TPU_TD , LS and LJT([email protected])
Maximum 60%
3 LS TPU_PD
LS Signed PA, sent to TPU PD
Notice 3:LS Job – LS Signed PA
TPU_PD, LS and LJT([email protected])
Maximum 81%
4 TPU_ PD
LS After Pengarah Signed PA , sent to TPU PD, and TPU PD signed eFee, and B1, then sent to LS to be automove to Land Office Notice 4: LS Job – PA Approved
LS, LJT and PTD/PTG([email protected])
Final 18%
112
T H A N K YO U
113