BOC SGEM S12-Gas Generators

10
SGEM 2006: SECTION 12 [GAS GENERATORS] 193 12 Laboratory Gas Generators 194 Gas Generators

description

GAS GENERATORS

Transcript of BOC SGEM S12-Gas Generators

  • SGEM 2006: SEction 12 [GaS GEnEratorS] 19312

    Laboratory Gas Generators 194

    Gas Generators

  • 12 Gas Generators

    SGEM 2006: SEction 12 [GaS GEnEratorS]194

    If your laboratory has one or more applications that demand a constant, high volume of laboratory gas you may be able to justify the cost (wish to consider the purchase of) of a laboratory gas generator which could save you money and make improvements to your productivity and laboratory safety at the same time.

    Gas Generators can be used with any instrumentation requiring high purity hydrogen, nitrogen or zero air, anywhere a standard electrical supply is available.

    Typical applications demanding constant high laboratory gas flows and where a laboratory gas generator may be justified include:

    LC/MS instruments

    Spectrometers

    Sample prep

    Auto samplers

    ELSD

    Domnick Hunter Gas Generators, which can be supplied by BOC, have many other benefits to consider in addition to the potential cost savings for high volume laboratory gas users:

    improve your analysis with UHP gas

    improved safety

    low pressure

    minimal stored gas

    no cylinder handling

    improved reliability and productivity

    never run out of gas

    compact modular design

    free up space

    use anywhere in lab

    aesthetic and ergonomic design

    integrate into any laboratory

    complement scientific instrumentation

    easy to operate and maintain

    quiet operation

    minimal maintenance

    after sale service

    1 year warranty

    global manufacturing support

    service contracts and extended warranties available

    BOC recommends that customers should always retain adequate back-up supplies of their laboratory gases in the event of a failure or shut down of their laboratory gas generator.

    applications Guide

    instrument Gas requirement Purity Flow rateGenerator recommended

    Products for Gas chromatography

    GC-FID Hydrogen for fuel gas UHP 3050 cc/min Hydrogen

    Zero air for flame gas Hydrocarbon-free 300500 cc/min Zero Air

    Hydrogen for capillary carrier gas

    UHP 10 cc/min Hydrogen

    Nitrogen for packed carrier gas

    UHP, zero grade 2050 cc/min Zero Nitrogen

    Nitrogen for make-up gas UHP, zero grade 3050 cc/min Zero Nitrogen

    GC-FPD Hydrogen for fuel gas UHP 6090 cc/min Hydrogen

    Zero Air for flame gas Hydrocarbon-free 90120 cc/min Zero Air

    GC-NPD Hydrogen for capillary gas UHP 50 cc/min Hydrogen

    Nitrogen for make-up gas UHP, zero grade 30 cc/min Zero Nitrogen

    GC-ECD Nitrogen for carrier gas UHP, zero grade 60 cc/min Zero Nitrogen

    Nitrogen for make-up gas UHP, zero grade 100 cc/min Zero Nitrogen

    GC-TCD Hydrogen as carrier gas UHP 50 cc/min Hydrogen

    GC-ATD Dry Air purge Clean and dry air

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS] 195

    Laboratory Gas Generators

    instrument Gas requirement Purity Flow rateGenerator recommended

    Products for LcMS instruments

    LCMS API/LCMS Air for nebulizer gas Clean and dry air, hydrocarbon free 99.5%

    18 L/min Clean Dry Air or Zero Air NitrogenAPCI, Electrospray

    LCMS/MS, TOFNitrogen for curtain and sheath shield gas

    535 L/min

    Products for Spectroscopy

    FT-IR Spectrometer Purge gas for sample compartment, optics, air bearing and microscope

    Clean dry, CO2 free 1485 L/min CO2 free air

    NMR Spectrometer Air for lifting spinning and ejecting

    Clean and dry air 300 L/min Clean Dry Air

    ICP Spectrometer Nitrogen or zero nitrogen for purge gas

    99.99 + % 9 L/min Nitrogen or Zero Nitrogen

    AA Spectrometer Air for oxidant gas Clean and dry air 20200 L/min Clean Dry Air

    Products for analysers

    TOC Dry air or Nitrogen for carrier gas or combustion gas

    Clean dry, CO2 free/ hydrocarbon free

    100500 cc/min CO2 free air/ Zero Air

    UHP 50700 cc/min Zero Nitrogen

    THA Zero air for FID Hydrocarbon free 50500 cc/min Zero Air

    Hydrogen for fuel gas UHP 550 cc/min Hydrogen

    DSC Air for air shield Clean and dry 100 cc/min Clean Dry Air

    TGA Nitrogen or dry air as furnace gas

    Clean and dry air or high purity N2

    100 cc/min Clean Dry Air or Nitrogen

    TOD Nitrogen carrier gas UHP, Zero Grade 300 cc/min Zero Nitrogen

    CO2 Analyser Calibration air Clean dry, CO2 free/ hydrocarbon free

    5501000 cc/min CO2 free air

    other laboratory applications

    Sample Prep Nitrogen for solvent evaporation

    9599% 130 L/min Nitrogen

    Auto-samplers Air for pneumatic controls

    Clean and dry 28 L/min Clean Dry Air

    Nitrogen for sample injector

    UHP, Zero Grade 550 cc/min Zero Nitrogen

    Circular Dichroism Nitrogen UHP, Zero Grade Zero Nitrogen

    ELSD Nitrogen 98% 28 L/min Nitrogen or

    Particle sizing by Laser Diffraction

    Clean and dry air for nebulizing gas

    Clean and dry air Clean Dry Air

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS]196

    Hydrogen Generators

    Capable of generating a continuous source of UHP hydrogen gas from de-ionised water and electricity for applications such as:

    GC-FID, NPD, FPD, TCD, ELCD, HALL, GC-carrier gas, THA

    BenefitsContinuous supply of GC quality hydrogen gas on demand. No warm-up period

    Improved productivity and chromatography results when using hydrogen as a carrier gas.

    Ultra safe operation from patented seven mode failure protection system

    Extended column service life with hydrogens lower elution temperatures

    Improved safety and efficiency

    No caustic solutions required

    FeaturesAutomatic H2 leak detection

    Self test fault diagnosis with visual and audible alarms

    High capacity water tank

    Filters offer protection against harsh lab environment

    Compact design

    No need for liquid electrolytes or caustic solutions

    No costly palladium purifier replacements

    Simple installation and operation

    CE and UL approved

    Hydrogen Generator selection chart (Single desiccant cartridge)

    ModelFlow rate (cc/min) Purity %

    Pressure (psi)

    connections BSP H2 outlet

    Voltage (Vac)

    Electrical consumption

    Dimensions (mm)

    Weight (kg)Width Height Depth

    20H 160 >99.999%* 07 bar (0100)

    1/8 Swagelok 110230 125 W 342 456 437 24

    40H 250 >99.999%* 07 bar (0100)

    1/8 Swagelok 110230 125 W 342 456 437 24

    60H 500 >99.999%* 07 bar (0100)

    1/8 Swagelok 110230 125 W 342 456 437 24

    * When used with oxygen / moisture trap

    High Purity Hydrogen MD Generator selection chart (regenerative Micro Dryer)

    ModelFlow rate (cc/min) Purity %

    Pressure (psi)

    connections BSP H2 outlet

    Voltage (Vac)

    Electrical consumption

    Dimensions (mm)

    Weight (kg)Width Height Depth

    20H-MD 160 >99.9999%* 07 bar (0100)

    1/8 Swagelok 110230 180 W 342 456 437 24

    40H-MD 250 >99.9999%* 07 bar (0100)

    1/8 Swagelok 110230 210 W 342 456 437 24

    60H-MD 500 >99.9999%* 07 bar (0100)

    1/8 Swagelok 110230 300 W 342 456 437 24

    Laboratory Gas Generators

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS] 197

    Laboratory Gas Generators

    Lc/MS nitrogen Generators

    Designed to meet the gas flow, purity and pressure requirements of LC/MS instruments using proven pressure swing adsorption (PSA) technology.

    Features and BenefitsDesigned in conjunction with instrument manufacturers - Ideally suited to nebulising, sheath and drying gas applications

    Wide range of flow rates available - Total flexibility allowing single or multiple instruments to be supplied

    Fully regenerative PSA technology - Reduced risk of gas contamination

    Guaranteed consistent nitrogen purity - Improved instrument stability and greater reproducibility of results

    Integral oil-free compressors - Fully secure supply no reliance on existing compressed air supplies

    Soundproofed compressor box - Low compressor noise

    Phthalate-free - Clean analyses

    Compact design - Fits under bench

    CE, UL and CRN approved - Peace of mind

    Lc/MS nitrogen Generator selection chart

    ModelFlow rate (cc/min) Purity %

    connections BSP

    Voltage (Vac)

    Dimensions (mm)

    Weight (kg)air inlet Gas outlet Width Height Depth

    LCMS-12-1* 12 0.5 1/8 110/230 345 873 663 90

    LCMS-15-0 15 0.5 1/4 1/8 110/230 510 705 559 89

    LCMS-15-1* 15 0.5 1/8 110/230 510 705 826 129

    LCMS-18-0 18 0.5 1/4 1/8 110/230 345 873 663 77

    LCMS-20-0 20 1 1/4 1/8 110/230 510 705 559 89

    LCMS-20-1* 20 1 1/8 110/230 510 705 826 129

    LCMS-30-0 30 1 1/4 1/8 110/230 510 705 760 135

    LCMS-30-1* 30 2 1/8 110/230 510 705 826 129

    LCMS-40-0 40 1 1/4 1/8 110/230 510 705 760 135

    * with integral compressor

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS]198

    nitrogen Generators

    Capable of generating nitrogen gas from pre-filtered compressed air for applications such as:

    ICP

    ELSD

    GC make up / carrier gas

    XRD

    Solvent evaporation

    NMR

    CD

    BenefitsDesigned to meet specific analytical instrument gas purityand flow requirements

    Uses reliable pressure swing adsorption technology (PSA)

    no need for secondary purification

    Constant flow of instrument grade nitrogen

    improved consistency and reproducibility of results

    improves laboratory efficiency

    Economy mode option turns off compressor when nitrogen supply is not required

    Simple Installation on or below bench top

    Quick, easy servicing typically less than 10 mins every 6 months

    nitrogen Generator selection chart

    ModelsFlow rate (L/min) Purity

    connections BSP

    Voltage (Vac)

    Dimensions (mm) Weight (kg)

    air inletGas outlet Width Height Depth

    Without compressor

    With compressor

    G1 0.55 10 ppm 1/8 1/8 110/230 345 842 413 52 56

    0.75 10 ppm

    G2 1.5 10 ppm 1/8 1/8 110/230 345 873 663 77 90

    2 10 ppm

    G3 2.5 100 ppm 1/8 1/8 110/230 345 873 663 71 83

    4 0.1%

    5 0.5%

    7 1%

    8 2%

    G4 5 100 ppm 1/8 1/8 110/230 345 873 663 77 90

    6 0.1%

    10 0.5%

    12.5 1%

    14 2%

    Laboratory Gas Generators

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS] 199

    Laboratory Gas Generators

    Zero nitrogen and Dry air Generators

    Suitable for applications such as:

    GC-FID

    THA

    Zero nitrogen and Dry air Generator selection chart

    ModelsFlow rate (L/min) Purity

    connections BSP

    Voltage (Vac)

    Dimensions (mm) Weight (kg)

    air inletGas outlet Width Height Depth

    Without compressor

    With compressor

    Zero nitrogen

    G5 1 10 ppm 1/8 1/8 110/230 345 842 413 51 55

    combined nitrogen and Dry air

    G6

    N2: 0.6 10 ppm 1/8

    1/8 110/230

    345

    842

    413

    54

    58

    Air: 1.5 -55C adp 1/8

    G7

    N2: 3 10 ppm 1/8

    1/8 110/230

    345

    842

    413

    80

    93

    Air: 3 -55C adp 1/8

    Dry air

    G8 3 -55C adp 1/8 1/8 110/230 345 842 413 50 54

    G9 6 -55C adp 1/8 1/8 110/230 345 842 413 50 54

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS]200

    Zero air Generators

    By connecting to a compressed air supply, a zero air generator will remove hydrocarbons and methane, making it ideal for use with the following applications:

    GC-FID, NPD, FDP

    LC/MS

    THA

    Gas sensing

    BenefitsContinuous flow of clean, dry air with ultra low residual methane content

    Improved instrument performance through reduced baseline noise and improved stability

    Cleaner air reduces frequency of instrument cleaning and re-calibrations

    Simple installation connect to any clean, dry compressed air source

    Improved safety no high pressure cylinders required

    Improved lab efficiency 24 hour operation

    FeaturesHigh performance catalyst and filtration system

    Eliminates the main contaminants in your compressed air supply (HCs and CH4)

    Purity

  • 12

    SGEM 2006: SEction 12 [GaS GEnEratorS] 201

    Laboratory Gas Generators

    clean Dry air Generators

    These desiccant dryers are ideal for laboratory use, providing a constant flow of clean, dry compressed air for:

    NMR, AA, GC, ATD

    Rheometer

    Sample prep

    Auto samplers and more

    FeaturesPoint of use installation provides clean and dry air where you need it

    Quite operation

    Compact and lightweight

    Can be bench or wall mounted

    Quick easy servicing

    clean Dry air Generator Selection chart

    Modelsoutput air Flow (L/min)

    Dimensions (mm) Weight (kg)

    DAS 1 70 422 x 149 11

    DAS 2 115 500 x 149 13

    DAS 3 182 616 x 149 16

    DAS 4 227 692 x 149 18

    DAS 5 295 847 x 149 20

    DAS 6 340 906 x 149 23

    DAS 7 453 1098 x 149 28

    Max. working pressure 12 bar g (175 psi g)

    Dewpoint -40C

    Purity Non methane HCs

  • 12 Gas Generators

    SGEM 2006: SEction 12 [GaS GEnEratorS]202