Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks...

16
Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method

Transcript of Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks...

Page 1: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Best Practices:

Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method

Page 2: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Practice Statement

Use rubber insulating gloves and sleeves while performing distribution power line tasks via the live line tool method.

Page 3: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Practice Description

Applies only to those applications where Line Workers are utilizing the “live line tool work method”

Donning of PPE shall be done in a safe location

Intent is to eliminate both M.A.D. encroachment violations and subsequent injuries.

Page 4: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Practice Description (cont’d) M.A.D. is defined as the Minimum Approach

Distance Defined by applicable Federal, State, or Local

regulation.

M.A.D. may also be known as •“Primary Contact Zone”

•“Minimum Working Distance,”

•“Within Reach”

•“Extended Reach”

Page 5: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Live Line Tool Method 1

Rubber insulating gloves and sleeves not required while using fiberglass insulating live line tools (“hot stick” method) under conditions where:•The Worker can not reach into the M.A.D.

•The worker can not extend any conductive object into the M.A.D.

•The worker can not extend any other part of the body into the M.A.D.

Page 6: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Live Line Method Line 2

Rubber insulating gloves and sleeves are required under conditions where:•The worker can reach into the M.A.D.

•The worker can extend any other part of the body into the M.A.D.

Approved protective equipment will be used to insulate and/or isolate energized conductors and/or parts

Page 7: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Live Line Method 3

Rubber insulating gloves shall be worn when tasks require the worker to:•Reach into the M.A.D.

•Extend any conductive object into the M.A.D.

•Extend any other part of the body into the M.A.D.

The gloves shall be worn when there is no upper arm exposure, even when proper cover is utilized.

Page 8: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Live Line Tool Method 4

Rubber insulating gloves and sleeves shall be worn where upper arm exposure exists when tasks require the worker to be in a position where:

•The worker can reach into the M.A.D.

•The worker can extend any conductive into the M.A.D.

•The worker can extend any other part of the body into the M.A.D.

Page 9: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

Benefits

Provides •specific use requirements that are proven

methods for•reducing electrical contact injuries

•Reducing electrical contact fatalities

•uniform use guidelines that can be applied industry wide.

Page 10: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

FAQ’s

When operating GOAB switches from the ground do I need glove and sleeves?•No, just rubber insulating gloves are required.

What is “upper arm” exposure?• the area on the arms not protected by rubber

insulating gloves that would be covered by rubber insulating sleeves.

Page 11: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

FAQ’s (cont’d)

I’m wearing rubber insulating gloves and the conductor is covered, do I need rubber insulating sleeves?•No, if no upper arm exposure.

•Yes, if upper arm exposure exists.

Page 12: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

I’m wearing rubber insulating gloves and the conductor is covered, do I need rubber insulating sleeves?•Rubber insulating gloves and sleeves shall be worn when

tasks require the worker •To enter the M.A.D.

•And there is the potential of upper arm exposure regardless of whether the conductors and equipment are covered

•Covering of conductors and equipment •Add an additional barrier or safeguard

•But not considered the primary form of protection for the worker

FAQ’s (cont’d)

Page 13: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

FAQ’s (cont’d) I am performing “hot stick” work and need to

encroach M.A.D. and perform a task by hand. What position do I need to be in to don my rubber insulating gloves or gloves and sleeves?•Performing “hot stick” work method does not require the

use of rubber insulating gloves or gloves and sleeves.

• If during this operation a task requires the worker to enter into the M.A.D. rubber insulating gloves and/or gloves and sleeves shall be donned prior to encroaching the applicable M.A.D.

•The worker shall maintain or move to a safe position so not to encroach M.A.D. during the donning of the PPE.

Page 14: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

General Use of Insulating Rubber Gloves and Sleeves

*Note* Although rubber insulating gloves and sleeves are not normally required when utilizing “hot sticking” work method the following is provided for informational purposes only.

Insulating Rubber gloves shall •Never be worn

•inside out

•without leather protectors

•Be exchanged •at any time they become damaged

•when the employee to whom they are assigned becomes suspicious of their condition

Page 15: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

General Use of Insulating Rubber Gloves and Sleeves

Leather protectors or over gloves shall not be worn expect over insulating rubber gloves

Insulating rubber gloves and sleeves • rated at the highest nominal anticipated

voltage shall be worn any time required by supervision

•Dielectric testing dates of shall be current

•Shall be visually inspected and gloves shall be air tested before each use

Page 16: Best Practices: Rubber Insulating Gloves and Sleeves while Performing Distribution Power Line Tasks via the Live Line Tool Method.

The ETD Partnership