1.Materials for TBB Adapter Sleeves, Withdrawal Sleeves ...

42

ｼ盡ｨﾌﾗｲ憘ｷｼｼﾊ・3.indd 42 2005-11-25 16:20:56

43

1.Materials for TBB Adapter Sleeves, Withdrawal Sleeves, Lock Nuts and Lock Washers

1.1 The high quality low carbon steel ---20F is adopted for gaining a better fitting with bearings and shafts,For its chemical composition, please refer to below Table 1.1

Table 1.1

Name StandardChemical composition (%)

C Mn Si Cr S ≤ P ≤

20F TBB 0.14~0.23 0.20~0.40 0.15~0.35 1.30~1.65 0.02 0.027

Note: TBB supplies all adapter sleeves,withdrawal sleeves, lock nuts and lock washers produced in 20F steel as normal products, unless otherwise specified before ordering.

2.Tolerance

2.1 Tolerance for dimension and shape of the adapter sleeves, please refer to Table 2.1 and Table 2.2

Table 2.1 Tolerance for width of the sleeve(Bi), length of its thread(a) and width of its locking gap(b① , f② )

Bi, a, b, f(mm)

Tolerance(μm)△ Bis △ as △ bs △ fs

over incl. high low high low high low high low

-

3

6

10

18

30

50

80

120

180

250

315

400

500

630

3

6

10

18

30

50

80

120

180

250

315

400

500

630

800

+200

+240

+290

+350

+420

+500

+600

+700

+800

+925

+1050

+1150

+1250

+1400

+1600

-200

-240

-290

-350

-420

-500

-600

-700

-800

-925

-1050

-1150

-1250

-1400

-1600

+200

+240

+290

+350

+420

+500

+600

+700

-

-

-

-

-

-

-

-200

-240

-290

-350

-420

-500

-600

-700

-

-

-

-

-

-

-

+140

+180

+220

+270

+330

+390

+460

-

-

-

-

-

-

-

-

0

0

0

0

0

0

0

-

-

-

-

-

-

-

-

+140

+180

+220

-

-

-

-

-

-

-

-

-

-

-

-

0

0

0

-

-

-

-

-

-

-

-

-

-

-

-

Note: ① b indicate wide gap . ② f indicate narrow gap


44

Table 2.2 Tolerance for internal diameter of the sleeve (d1mp), for thread, for diameter of taper(D1s) and run-out(KDo) of the tapered surface.

d1(mm)over incl.

Tolerance(μm)

△ d1mp Vd1mp △ D1s Vdop △ D1mp- △ d1mp ToleranceFor thread KDohigh low max. high low max. high low

-

18

30

50

80

120

180

250

315

400

500

630

800

18

30

50

80

120

180

250

315

400

500

630

800

1000

+35

+42

+50

+60

+70

+80

+92

+105

+115

+125

+140

+160

+180

-35

-42

-50

-60

-70

-80

-92

-105

-115

-125

-140

-160

-180

27

33

39

46

54

63

72

81

89

97

110

125

140

+33

+39

+46

+54

+63

+72

+81

+89

+97

+110

+125

+140

+165

0

0

0

0

0

0

0

0

0

0

0

0

0

10

13

15

20

25

31

38

44

50

56

63

94

125

+18

+21

+25

+30

+35

+40

+46

+52

+57

+63

+70

+80

+90

0

0

0

0

0

0

0

0

0

0

0

0

0

For general

Thread 6g

tolerance is

adopted

For T type

thread 6e

tolerance is

adopted

20

25

30

40

40

50

50

60

60

60

80

80

100

3.Roughness of the Surface

d1 (mm)

over incl.

Roughness

Internal surface

Taper surface

Thread Other surface Kdo

- 120 1.6 0.80 6.3 5 20

120 500 2.5 1.25 6.3 5 25

500 - 3.2 1.60 6.3 5 30

4.Checking Method

4.1 The outer appearance of the adapter sleeve is checked by sight.4.2 Roughness of the main surfaces of the adapter sleeve is sightly checked by comparing with a

sample adapter sleeve confirmed by both sides.4.3 Thread is checked by standard thread stop-through gage.


45

Inner bore Adapter number Nominal dimensions Weight

H HE HS HA H HE HS HA B1 B2 B3 B4

d

mm inch inch inch mm mm mm mm kg17 _ 5/8 _ H204 _ HS204 _ 24 7 20 32 0.041

20 3/4 7/8 13/16 H205 HE205 HS205 HA205 26 8 25 38 0.070

25 1 7/8 15/16 H206 HE206 HS206 HA206 27 8 30 45 0.099

30 1-1/4 1-1/8 1-3/16 H207 HE207 HS207 HA207 29 9 35 52 0.125

35 1-1/4 1-3/8 1-5/16 H208 HE208 HS208 HA208 31 10 40 58 0.174

40 1-1/2 1-5/8 1-7/16 H209 HE209 HS209 HA209 33 11 45 65 0.226

45 1-3/4 1-5/8 1-11/16 H210 HE210 HS210 HA210 35 12 50 70 0.274

50 2 1-7/8 1-15/16 H211 HE211 HS211 HA211 37 12 55 75 0.308

55 2-1/4 2-1/8 2-1/16 H212 HE212 HS212 HA212 38 13 60 80 0.346

60 2-1/4 2-3/8 2-3/16 H213 HE213 HS213 HA213 40 14 65 85 0.401

60 _ _ _ H214 _ _ _ 41 14 70 92 0.550

65 2-1/2 2-5/8 2-7/16 H215 HE215 HS215 HA215 43 15 75 98 0.708

70 2-3/4 _ 2-11/16 H216 HE216 _ HA216 46 17 80 105 0.881

75 3 _ 2-15/16 H217 HE217 _ HA217 50 18 85 110 1.020

80 3-1/4 _ 3-3/16 H218 HE218 _ HA218 52 18 90 120 1.180

85 3-1/4 _ 3-5/16 H219 HE219 _ HA219 55 19 95 125 1.370

90 3-1/2 _ 3-7/16 H220 HE220 _ HA220 58 20 100 130 1.490

95 _ _ _ H221 _ _ _ 60 20 105 140 1.700

100 4 _ 3-15/16 H222 HE222 _ HA222 63 21 110 145 1.930

B1

B2

B4dB1

B2

B4dB3 B3


46


H HE HS HA H HE HS HA B1 B2 B3 B4d

mm inch inch inch mm mm mm mm kg17 _ 5/8 _ H304 _ HS304 _ 28 7 20 32 0.04520 3/4 7/8 13/16 H305 HE305 HS305 HA305 29 8 25 38 0.07525 1 7/8 15/16 H306 HE306 HS306 HA306 31 8 30 45 0.10930 1-1/4 1-1/8 1-3/16 H307 HE307 HS307 HA307 35 9 35 52 0.14235 1-1/4 1-3/8 1-5/16 H308 HE308 HS308 HA308 36 10 40 58 0.18940 1-1/2 1-5/8 1-7/16 H309 HE309 HS309 HA309 39 11 45 65 0.24845 1-3/4 1-5/8 1-11/16 H310 HE310 HS310 HA310 42 12 50 70 0.30250 2 1-7/8 1-15/16 H311 HE311 HS311 HA311 45 12 55 75 0.34555 2-1/4 2-1/8 2-1/16 H312 HE312 HS312 HA312 47 13 60 80 0.39360 2-1/4 2-3/8 2-3/16 H313 HE313 HS313 HA313 50 14 65 85 0.45960 _ _ _ H314 _ -- -- 52 14 70 92 0.72365 2-1/2 2-5/8 2-7/16 H315 HE315 HS315 HA315 55 15 75 98 0.83070 2-3/4 2-7/8 2-11/16 H316 HE316 HS316 HA316 59 17 80 105 1.00075 3 _ 2-15/16 H317 HE317 _ HA317 63 18 85 110 1.18080 3-1/4 3-1/8 3-3/16 H318 HE318 HS318 HA318 65 18 90 120 1.37085 3-1/4 _ 3-5/16 H319 HE319 _ HA319 68 19 95 125 1.56090 3-1/2 _ 3-7/16 H320 HE320 _ HA320 71 20 100 130 1.69095 _ _ _ H321 _ _ _ 74 20 105 140 1.950

100 4 _ 3-15/16 H322 HE322 _ HA322 77 21 110 145 2.180

B1

B2

B4dB1

B2

B4dB3 B3


47


H HE HS HA H HE HS HA B1 B2 B3 B4

d

mm inch inch inch mm mm mm mm kg17 _ 5/8 _ H2304 _ HS2304 _ 31 7 20 32 0.04920 3/4 7/8 13/16 H2305 HE2305 HS2305 HA2305 35 8 25 38 0.08725 1 7/8 1-5/16 H2306 HE2306 HS2306 HA2306 38 8 30 45 0.12630 1-1/4 1-1/8 1-3/16 H2307 HE2307 HS2307 HA2307 43 9 35 52 0.16535 1-1/4 1-3/8 1-5/16 H2308 HE2308 HS2308 HA2308 46 10 40 58 0.22440 1-1/2 1-5/8 1-7/16 H2309 HE2309 HS2309 HA2309 50 11 45 65 0.28045 1-3/4 1-5/8 1-11/16 H2310 HE2310 HS2310 HA2310 55 12 50 70 0.36250 2 1-7/8 1-15/16 H2311 HE2311 HS2311 HA2311 59 12 55 75 0.24055 2-1/4 2-1/8 2-1/16 H2312 HE2312 HS2312 HA2312 62 13 60 80 0.48160 2-1/4 2-3/8 2-3/16 H2313 HE2313 HS2313 HA2313 65 14 65 85 0.55760 _ _ _ H2314 _ -- -- 68 14 70 92 0.89765 2-1/2 2-5/8 2-7/16 H2315 HE2315 HS2315 HA2315 73 15 75 98 1.05070 2-3/4 2-7/8 2-11/16 H2316 HE2316 HS2316 HA2316 78 17 80 105 1.28075 3 _ 2-15/16 H2317 HE2317 _ HA2317 82 18 85 110 1.45080 3-1/4 3-1/8 3-3/16 H2318 HE2318 HS2318 HA2318 86 18 90 120 1.69085 3-1/4 _ 3-5/16 H2319 HE2319 _ HA2319 90 19 95 125 1.92090 3-1/2 _ 3-7/16 H2320 HE2320 _ HA2320 97 20 100 130 2.15095 _ _ _ H2321 _ _ _ 101 20 105 140 2.460

100 4 _ 3-15/16 H2322 HE2322 _ HA2322 105 21 110 145 2.740110 4-1/4 _ 4-3/16 H2324 HE2324 _ HA2324 112 22 120 155 3.190115 4-1/2 _ 4-7/16 H2326 HE2326 _ HA2326 121 23 130 165 4.600125 5 4-13/16 4-15/16 H2328 HE2328 HS2328 HA2328 131 24 140 180 5.550135 5-1/4 _ 5-3/16 H2330 HE2330 _ HA2330 139 26 150 195 6.630140 5-1/2 _ 5-7/16 H2332 HE2332 _ HA2332 147 28 160 210 9.140150 6 _ 5-15/16 H2334 HE2334 _ HA2334 154 29 170 220 10.200160 6-1/2 _ 6-7/16 H2336 HE2336 _ HA2336 161 30 180 230 11.300170 6-3/4 _ 6-15/16 H2338 HE2338 _ HA2338 169 31 190 240 12.600180 7 _ 7-3/16 H2340 HE2340 _ HA2340 176 32 200 250 13.900200 _ _ _ H2344 -- _ -- 183 32 220 280 16.700220 _ _ _ H2348 -- _ -- 196 34 240 300 19.700240 _ _ _ H2352 -- _ -- 208 36 260 330 24.200260 _ _ _ H2356 -- _ -- 221 38 280 350 27.800

B1

B2

B4dB1

B2

B4dB3 B3


48


H HE HA H HE HA B1 B2 B3 B4 B5d

mm inch inch mm mm mm mm mm kg

110 4-1/4 4-3/16 H3024 HE3024 HA3024 72 22 120 155 -- 1.960

115 4-1/2 4-7/16 H3026 HE3026 HA3026 80 23 130 165 -- 2.950

125 5 4-15/16 H3028 HE3028 HA3028 82 24 140 180 -- 3.380

135 5-1/4 5-3/16 H3030 HE3030 HA3030 87 26 150 195 -- 4.100

140 5-1/2 5-7/16 H3032 HE3032 HA3032 93 28 160 210 -- 5.400

150 6 5-15/16 H3034 HE3034 HA3034 101 29 170 220 -- 6.200

160 6-1/2 6-7/16 H3036 HE3036 HA3036 109 30 180 230 -- 7.100

170 6-3/4 6-15/16 H3038 HE3038 HA3038 112 31 190 240 -- 7.750

180 7 7-3/16 H3040 HE3040 HA3040 120 32 200 250 -- 9.600

200 _ 7-15/16 H3044 _ HA3044 128 35 220 280 -- 10.700

220 _ 8-15/16 H3048 _ HA3048 133 37 240 300 -- 13.800

240 _ 9-7/16 H3052 _ HA3052 147 39 260 330 -- 16.100

260 _ 10-7/16 H3056 _ HA3056 152 40 280 350 -- 17.900

280 _ 10-15/16 H3060 _ HA3060 168 40 300 380 53 23.200

300 _ 11-15/16 H3064 _ HA3064 171 42 320 400 56 25.000

320 _ 12-7/16 H3068 _ HA3068 187 55 340 440 72 29.200

340 _ 13-7/16 H3072 _ HA3072 188 58 360 460 75 32.600

360 _ 13-15/16 H3076 _ HA3076 193 60 380 490 77 37.800

380 _ _ H3080 _ -- 210 62 400 520 82 43.500

400 _ _ H3084 _ _ 212 70 420 540 90 45.600

410 _ _ H3088 _ _ 228 70 440 560 90 67.500

430 _ _ H3092 _ _ 234 75 460 580 95 71.400

450 _ _ H3096 _ _ 237 75 480 620 95 75.500

470 _ _ H30/500 _ _ 247 80 500 630 100 84.000

B1

B2

B4dB1

B2

B4dB3 B3


49

InnerBore

d

Adapter number G1 B1 B2 B3 G Weight

mm mm mm mm mm mm kg

35 AH208 6 25 27 40 M45×1.5 0.081

40 AH209 6 26 29 45 M50×1.5 0.095

45 AH210 7 28 31 50 M55×2 0.114

50 AH211 7 29 32 55 M60×2 0.132

55 AH212 8 32 35 60 M65×2 0.161

60 AH213 8 32.5 36 65 M75×2 0.213

65 AH214 8 33.5 37 70 M80×2 0.240

70 AH215 8 34.5 38 75 M85×2 0.259

75 AH216 8 35.5 39 80 M90×2 0.284

80 AH217 9 38.5 42 85 M95×2 0.314

85 AH218 9 40 44 90 M100×2 0.351

90 AH219 10 43 47 95 M105×2 0.403

95 AH220 10 45 49 100 M110×2 0.481

105 AH222 11 50 54 110 M120×2 0.547

115 AH224 12 53 57 120 M130×2 0.679

125 AH226 12 53 57 130 M140×2 0.725

135 AH228 13 56 61 140 M150×2 0.818

145 AH230 14 60 65 150 M160×3 0.963

150 AH232 15 64 69 160 M170×3 1.700

160 AH234 16 69 74 170 M180×3 1.980

170 AH236 16 69 74 180 M190×3 2.040

180 AH238 17 73 78 190 Tr205×4 2.520

190 AH240 18 77 82 200 Tr215×4 2.870

200 AH244 18 85 91 220 Tr235×4 5.490

220 AH248 22 96 102 240 Tr260×4 7.340

240 AH252 23 105 111 260 Tr280×4 8.800

260 AH256 23 105 113 280 Tr300×4 9.420

d

G1

B1

B2

B3


50

InnerBore

d



35 AH308 6 29 32 40 M45×1.5 0.090

40 AH309 6 31 34 45 M50×1.5 0.109

45 AH×310 7 35 38 50 M55×2 0.137

50 AH×311 7 37 40 55 M60×2 0.161

55 AH×312 8 40 43 60 M65×2 0.189

60 AH313 8 42 45 65 M75×2 0.253

65 AH314 8 43 47 70 M80×2 0.280

70 AH315 8 45 49 75 M85×2 0.313

75 AH316 8 48 52 80 M90×2 0.365

80 AH×317 9 52 56 85 M95×2 0.429

85 AH×318 9 53 57 90 M100×2 0.461

90 AH×319 10 57 61 95 M105×2 0.532

95 AH×320 10 59 63 100 M110×2 0.582

105 AH×322 12 63 67 110 M120×2 0.663

115 AH×324 13 69 73 120 M130×2 0.866

125 AH×326 14 74 78 130 M140×2 1.020

135 AH×328 14 77 82 140 M150×2 1.160

145 AH×330 15 83 88 150 M165×3 1.500

150 AH332 16 88 93 160 M180×3 2.690

160 AH334 17 93 98 170 M190×3 3.070

d

G1

B1

B2

B3


51

InnerBore

d



35 AH2308 7 40 43 40 M45×1.5 0.128

40 AH2309 7 44 47 45 M50×1.5 0.164

45 AH×2310 9 50 53 50 M55×2 0.209

50 AH×2311 10 54 57 55 M60×2 0.253

55 AH×2312 11 58 61 60 M65×2 0.297

60 AH×2313 12 61 64 65 M75×2 0.395

65 AH×2314 12 64 68 70 M80×2 0.466

70 AH×2315 12 68 72 75 M85×2 0.534

75 AH×2316 12 71 75 80 M90×2 0.597

80 AH×2317 13 74 78 85 M95×2 0.670

85 AH×2318 14 79 83 90 M100×2 0.779

90 AH×2319 16 85 89 95 M105×2 0.886

95 AH×2320 16 90 94 100 M110×2 0.998

105 AH×2322 16 98 102 110 M125×2 1.350

115 AH×2324 17 105 109 120 M135×2 1.600

125 AH×2326 19 115 119 130 M145×2 1.970

135 AH×2328 20 125 130 140 M155×3 2.330

145 AH×2330 24 135 140 150 M165×3 2.820

150 AH×2332 24 140 146 160 M180×3 4.720

160 AH2334 24 146 152 170 M190×3 5.250

170 AH2336 26 154 160 180 M200×3 5.830

180 AH2338 26 160 167 190 Tr210×4 6.630

190 AH2340 30 170 177 200 Tr220×4 7.540

200 AH2344 30 181 181 220 Tr240×4 13.500

220 AH2348 30 189 189 240 Tr260×4 15.500

240 AH2352 30 205 205 260 Tr290×4 19.600

260 AH2356 30 212 212 280 Tr310×5 21.600

d

G1

B1

B2

B3


52

InnerBore

d



115 AH×3024 13 60 64 120 M130×2 0.750

125 AH×3026 14 67 71 130 M140×2 0.930

135 AH×3028 14 68 73 140 M150×2 1.100

145 AH×3030 15 72 77 150 M160×3 1.150

150 AH×3032 16 77 82 160 M170×3 2.060

160 AH3034 17 85 90 170 M180×3 2.430

170 AH3036 17 92 98 180 M190×3 2.810

180 AH3038 18 96 102 190 Tr205×4 3.320

190 AH3040 19 102 108 200 Tr215×4 3.800

200 AH3044 20 111 117 220 Tr235×4 7.400

220 AH3048 21 116 123 240 Tr260×4 8.750

240 AH3052 23 128 135 260 Tr280×4 10.700

260 AH3056 24 131 139 280 Tr300×4 12.000

280 AH3060 26 145 153 300 Tr320×5 14.400

300 AH3064 27 149 157 320 Tr345×5 16.000

320 AH3068 28 162 171 340 Tr365×5 19.500

340 AH3072 30 167 176 360 Tr385×5 21.000

360 AH3076 31 170 180 380 Tr410×5 23.200

380 AH3080 33 183 193 400 Tr430×5 27.300

400 AH3084 34 186 196 420 Tr450×5 29.000

420 AH×3088 35 194 205 440 Tr470×5 32.000

440 AH×3092 37 202 213 460 Tr490×5 35.200

460 AH×3096 38 205 217 480 Tr520×5 39.200

d

G1

B1

B2

B3


53

InnerBore

d



95 AH×3120 11 64 68 100 M110×2 0.650

105 AH×3122 11 68 72 110 M120×2 0.760

115 AH×3124 12 75 79 120 M130×2 0.950

125 AH×3126 12 78 82 130 M140×2 1.080

135 AH×3128 14 83 88 140 M150×2 1.280

145 AH×3130 15 96 101 150 M165×3 1.790

150 AH3132 16 103 108 160 M180×3 3.210

160 AH3134 16 104 109 170 M190×3 3.400

170 AH3136 19 116 122 180 M200×3 4.220

180 AH3138 20 125 131 190 M210×4 4.890

190 AH3140 21 134 140 200 Tr220×4 5.490

200 AH3144 23 145 151 220 Tr240×4 10.400

220 AH3148 25 154 161 240 Tr260×4 12.000

240 AH3152 26 172 179 260 Tr290×4 16.200

260 AH3156 28 175 183 280 Tr310×5 17.500

280 AH3160 30 192 200 300 Tr330×5 20.800

300 AH3164 31 209 217 320 Tr350×5 24.500

320 AH3168 33 225 234 340 Tr370×5 29.000

340 AH3172 35 229 238 360 Tr400×5 33.000

360 AH3176 36 232 242 380 Tr420×5 35.700

380 AH3180 38 240 250 400 Tr440×5 39.500

400 AH3184 40 266 276 420 Tr460×5 46.500

420 AH3188 42 270 281 440 Tr480×5 49.800

440 AH3192 43 285 296 460 Tr510×6 57.900

460 AH3196 45 295 307 480 Tr530×6 63.100

d

G1

B1

B2

B3


54

InnerBore

d



85 AH×3218 10 63 67 90 M100×2 0.570

90 AH×3219 11 67 71 95 M105×2 0.900

95 AH×3220 11 73 77 100 M110×2 0.760

105 AH×3222 11 82 86 110 M125×2 1.050

115 AH×3224 13 90 94 120 M135×2 1.300

125 AH×3226 15 98 102 130 M145×2 1.550

135 AH×3228 15 104 109 140 M155×3 1.850

145 AH×3230 17 114 119 150 M165×3 2.200

150 AH×3232 20 124 130 160 M180×3 4.000

160 AH3234 24 134 140 170 M190×3 4.800

170 AH3236 24 140 146 180 M200×3 5.250

180 AH3238 25 145 152 190 M210×4 5.900

190 AH3240 25 153 160 200 T220×4 6.600

280 AH3260 34 228 236 300 T330×5 23.500

300 AH3264 36 246 254 320 T350×5 27.500

320 AH3268 38 264 273 340 T370×5 32.000

340 AH3272 40 274 283 360 T400×5 33.000

360 AH3276 42 284 294 380 T420×5 45.500

400 AH3280 44 303 312 400 T440×6 51.500

400 AH3284 46 321 331 420 T460×6 59.000

420 AH3288 48 330 341 440 T480×5 64.500

440 AH×3292 50 349 360 460 T510×5 75.500

460 AH×3296 52 364 376 480 T530×6 82.500

480 AH×32/500 54 393 405 500 T550×6 95.000

d

G1

B1

B2

B3


55

G Lock nut number B b d1 d2 h Weightmm mm mm mm mm mm kg

M10×0.75 KM0 4 3 13.5 18 2 0.006

M12×1 KM1 4 3 17 22 2 0.008

M15×1 KM2 5 4 21 25 2 0.012

M17×1 KM3 5 4 24 28 2 0.014

M20×1 KM4 6 4 26 32 2 0.020

M22×1 KM/22 6 4 28 34 2 0.022

M25×1.5 KM5 7 5 32 38 2 0.028

M28×1.5 KM/28 7 5 36 42 2 0.032

M30×1.5 KM6 7 5 38 45 2 0.038

M32×1.5 KM/32 8 5 40 48 2 0.042

M35×1.5 KM7 8 5 44 52 2 0.058

M40×1.5 KM8 9 6 50 58 2.5 0.078

M45×1.5 KM9 10 6 56 65 2.5 0.110

M50×1.5 KM10 11 6 61 70 2.5 0.140

M55×2 KM11 11 7 67 75 3 0.150

M60×2 KM12 11 7 73 80 3 0.160

M65×2 KM13 12 7 79 85 3 0.190

M70×2 KM14 12 8 85 92 3.5 0.220

M75×2 KM15 13 8 90 98 3.5 0.270

M80×2 KM16 15 8 95 105 3.5 0.360

M85×2 KM17 16 8 102 110 3.5 0.420

M90×2 KM18 16 10 108 120 4 0.510

M95×2 KM19 17 10 113 125 4 0.580

M100×2 KM20 18 10 120 130 4 0.680

M105×2 KM21 18 12 126 140 5 0.810

m

h

B

30。

d1d2 G

r


56


M110×2 KM22 19 12 133 145 5 0.890

M115×2 KM23 19 12 137 150 5 0.910

M120×2 KML24 20 12 135 145 5 0.690

M120×2 KM24 20 12 138 155 5 0.980

M125×2 KM25 21 12 148 160 5 1.100

M130×2 KML26 21 12 145 155 5 0.840

M130×2 KM26 21 12 149 165 5 1.200

M135×2 KM27 22 14 160 175 6 1.400

M140×2 KML28 22 14 155 165 6 0.920

M140×2 KM28 22 14 160 180 6 1.400

M145×2 KM29 24 14 171 190 6 1.850

M150×2 KML30 24 14 170 180 6 1.300

M150×2 KM30 24 14 171 195 6 1.850

M155×3 KM31 25 16 182 200 7 2.050

M160×3 KML32 25 16 180 190 7 1.400

M160×3 KM32 25 16 182 210 7 2.250

M165×3 KM33 26 16 193 210 7 2.300

M170×3 KML34 26 16 190 200 7 1.600

M170×3 KM34 26 16 193 220 7 2.250

m

h

B

30。

d1d2 G

r


57


M180×3 KML36 27 18 200 210 7 1.800

M180×3 KM36 27 18 203 230 8 2.700

M190×3 KML38 28 18 210 220 7 1.900

M190×3 KM38 28 18 214 240 8 3.000

M200×3 KML40 29 18 222 240 8 2.600

M200×3 KM40 29 18 226 250 8 3.300

Tr205×4 KML41 30 18 232 250 8 4.200

Tr215×4 KM42 30 20 238 270 10 5.100

Tr215×4 KML43 30 20 242 260 9 4.350

Tr220×4 KM44 32 20 250 280 10 4.750

Tr230×4 KM46 34 20 260 290 10 5.450

Tr235×4 KML47 34 20 262 280 9 5.300

Tr240×4 KM48 34 20 270 300 10 5.600

Tr250×4 KM50 36 20 290 320 10 7.450

Tr260×4 KM52 36 24 300 330 12 7.550

Tr280×4 KM56 38 24 320 350 12 8.650

f

f 1d

F

25。

d2d1

B


58

Innerbore

d

Lock nut number B d1 d2 F f f 1 Weight

mm mm mm mm mm mm mm kg

10 MB0 1 13.5 21 8.5 3 3 1.000

12 MB1 1 17 25 10.5 3 3 2.000

15 MB2 1 21 28 13.5 4 4 2.600

17 MB3 1 24 32 15.5 4 4 3.200

20 MB4 1 26 36 18.5 4 4 3.500

25 MB5 1.25 32 42 23 5 5 6.400

30 MB6 1.25 38 49 27.5 5 5 7.800

35 MB7 1.25 44 57 32.5 5 5 10.500

40 MB8 1.25 50 62 37.5 6 6 12.400

45 MB9 1.25 56 69 42.5 6 6 15.200

50 MB10 1.25 61 74 47.5 6 6 16.000

55 MB11 1.5 67 81 52.5 7 8 19.600

60 MB12 1.5 73 86 57.5 7 8 25.300

65 MB13 1.5 79 92 62.5 7 8 29.000

70 MB14 1.5 85 98 66.5 8 8 33.400

75 MB15 1.5 90 104 71.5 8 8 35.600

80 MB16 1.8 95 112 76.5 8 10 46.500

85 MB17 1.8 102 119 81.5 8 10 52.400

90 MB18 1.8 108 126 86.5 10 10 61.000

95 MB19 1.8 113 133 91.5 10 10 67.000

100 MB20 1.8 120 142 96.5 10 12 76.500

105 MB21 1.8 126 145 100.5 12 12 82.600

110 MB22 1.8 133 154 105.5 12 12 94.000

115 MB23 2 137 159 110.5 12 12 103.000

120 MBL24 2 135 152 115 12 14 70.000

f

f 1d

F

25。

d2d1

B


59

Innerbore

d

Lock nut number B d1 d2 F f f 1 Weight

mm mm mm mm mm mm mm kg

120 MB24 2 138 164 115 12 14 105.000

125 MB25 2 148 170 120 12 14 118.000

130 MBL26 2 145 161 125 12 14 80.000

130 MB26 2 149 175 125 12 14 118.000

135 MB27 2 160 185 130 14 14 144.000

140 MBL28 2 155 172 135 14 16 90.000

140 MB28 2 160 192 135 14 16 144.000

145 MB29 2 172 202 140 14 16 168.000

150 MBL30 2 170 189 145 14 16 100.000

150 MB30 2 171 205 145 14 16 155.000

155 MB31 2.5 182 212 147.5 16 16 209.000

160 MBL32 2.5 180 199 154 16 18 140.000

160 MB32 2.5 182 217 154 16 18 222.000

165 MB33 2.5 193 222 157.5 16 18 241.000

170 MBL34 2.5 190 211 164 16 18 150.000

170 MB34 2.5 193 232 164 16 18 248.000

180 MBL36 2.5 200 222 174 18 20 160.000

180 MB36 2.5 203 242 174 18 20 258.000

190 MBL38 2.5 210 232 184 18 20 178.000

190 MB38 2.5 214 252 184 18 20 278.000

200 MBL40 2.5 222 245 194 18 20 220.000

200 MB40 2.5 226 262 194 18 20 293.000

200 MB44 3 250 292 213 20 24 350.000

240 MB48 3 270 312 233 20 24 450.000

260 MB52 3 300 342 253 24 28 600.000

280 MB56 3 320 362 273 24 28 1050.000

f

f 1d

F

25。

d2d1

B


1.Materials for TBB Adapter Sleeves, Withdrawal Sleeves ...

Documents

Transcript of 1.Materials for TBB Adapter Sleeves, Withdrawal Sleeves ...