BATH DRAIN - Kohler Co.resources.kohler.com/plumbing/kohlerapac/pdf/19321T-CP.pdfWrap the plier head...
Transcript of BATH DRAIN - Kohler Co.resources.kohler.com/plumbing/kohlerapac/pdf/19321T-CP.pdfWrap the plier head...
-1-
INSTALLATION INSTRUCTIONS
K-19321T
BATH DRAIN
�
�
Please read these instructions carefully tofamiliarize yourself with the required tools,materials, and installation sequences. Follow thesections that pertain to your particular installation.This will help you avoid costly mistakes. In additionto proper installation, read all operating and safetyinstructionsAll information is based on the latest productinformation available at the time of publication.Kohler China Ltd. reserves the right to makechanges in product characteristics, packaging, oravailability at any time without notice.
�
�
BEFORE YOU BEGINBEFORE YOU BEGIN
NOTES
�
�
�
�
�
Observe all local plumbing and plumbing codes.
Inspect waste and supply tubing; replace if
necessary.
The drain has removable parts.
Drain T is reversible for vertical or horizontal
drainage.
Do not use sharp and hard objects when taking out
the drain plug to avoid scratching it.
" "
�
�
�
�
�
T
Tools Required
�
�
�
�
�
�
Assorted screwdriversAdjustable or open end wrenchPipe wrenchesPliersManual hacksawLong flat nose pliers
�
�
�
�
�
�
SHANGHAI KOHLER LTD., NO.368, MIN LE ROAD,FENG XIAN DISTRICT, SHANGHAI, CHINA POST CODE 201419
368 201419
©
©
Copyright Kohler China Investment Co., Ltd. 2016
20161260047-T01-B
ROUGHING-IN
202
80
101
280 ~ 540
Fig.#11
-2-
INSTALLATION PREPARATIONSINSTALLATION PREPARATIONS
Disassemble the overflow plate kit and the base kitfrom the overflow base.
Pull the plug off the drain body.
Fig.#22
Fig.#33
Fig.#44
Pull out the control wire head from the bottom of
overflow pipe. Insert a string into the back of the button
and pull out the whole control wire assembly.
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value UNIT: mm
2 Pull Out2
1 Pull Out1
Pull Out
Plug
Strainer
1260047-T01-B
-3-
When installing baths with different height, you may need
to cut the pipes as shown to suit the height of the bath.
Attach the gasket to the overflow ell, as shown. Applysilicon sealant.
Cut Placement
INSTALLATION
Gasket
Drain Ell
Bath
Wrap the plier head with adhesive tape and then insert
it into the top of the strainer to tighten the drain ell
securely, as shown. Make sure the drain ell tube is
facing the front of the bath. Then apply silicone sealant
around the strainer.
Fig.#66
Fig.#88
Fig.#99
Insert strainer into the gasket, position plain gasketbetween the drain ell and the bottom of the bath. Turnthe strainer into the drain ell. Strainer Gasket
Unscrew the valve body using packed wrench.
Fig.#55
Cross Wrench
Unscrew Counterclockwise
Trigger Kit
Strainer
Apply Silicon Sealant
Gasket
Overflow Ell
Overflow Pipe
Fig.#77
Long Flat Nose Pliers
Strainer
1260047-T01-B
-4-
For vertical drainage installations: assemble parts asshown. Align the parts with the drain base. Align andtighten the nuts.
Fig.#1111
Fig.#1212
Fig.#1313
Fig.#1414
Fig.#1515
Assemble the overflow plate kit and the base kit back tothe overflow base from the inside of bath tub.
Fig.#1010
For horizontal drainage installations: assemble parts asshown. Align the parts with the drain base. Align andtighten the nuts.
Insert the control wire into the center of the overflow
hole.
After inserting the whole control wire, insert the rib on
the button into the slot on the button base until a "click"
is heard.
Pull the tail of control wire from the drain hole. Pull Out
1260047-T01-B
-5-
Remove the rubber cover from the wire as shown, thenfasten the control wire with the trigger kit.
Fig.#1616
Hide the control wire into the pipe as shown.
Note: Do not over bend the wire at all
bending positions. Leave arcs as big as
possible to avoid too much pressure.
Otherwise, the button may not restore to its
original position.
Fasten the trigger kit on the strainer.
Push the button on overflow, so the ejector pin of thetrigger kit on high position, then push the plug on thetrigger kit until a "click".
Attention:
After install, push the button repeatedly, make sure the
plug could open and close normally. Run water into the
bath, check the drain connections for leaks.
Fig.#1717
Fig.#1818
Fig.#1919
Control Wire
Cross Wrench
Fasten Clockwise
Trigger Kit
Strainer
Plug
Push Down
Fasten As Shown
Trigger Kit Ejector
1260047-T01-B
MAINTENANCE
Fig.#2020
�
�
Pull off the plug, unscrew the trigger kit, pull thecontrol wire out to clean the hair on the wire.The accessories should be washed with warm waterand a soft cloth or sponge. Do not use abrasivecleaners or cleaners containing bleach.
�
�
Pull Out
Plug
Strainer
Cross Wrench
Unscrew Counterclockwise
Trigger Kit
Strainer
-6-1260047-T01-B