Basic Log Interpretation

11

Introduction to Log Interpretation


© Schlumberger 1999

22


Log InterpretationInterpretation is defined as the action of explaining the meaning of something.

Log Interpretation is the explanation of logs ρρρρb, GR, Resistivity, etc. in terms of well and reservoir parameters, zones, porosity, oil saturation, etc.

Log interpretation can provide answers to questions on:

33


Why Run Logs

44


The Reservoir

55


Requirements of a reservoir

To form a reservoir needs

- source of organic material (terrestrial or marine)

- a suitable combination of heat, pressure and time

- an oxygen free environment

- a suitable basin

66


Reservoir Geometry

77


Reservoir elements

The major elements of a reservoir are

• permeable rock stores the hydrocarbon• source rock produces hydrocarbon• impermeable rock traps hydrocarbon• trap captures fluids

A

11

Reservoir Rocks

Reservoir Rocks


22

Reservoir Rocks

The Earth

��

��

Crust

MantleCoreInner Core

solid

liquid

plastic

plastic

750 miles 1400 miles 1800 miles

10 miles

ρ = 10.7 g/cc ρ = 4.0 g/cc

33

Reservoir Rocks

The Earth 2

44

Reservoir Rocks

Plate Tectonics 1

55

Reservoir Rocks

Compressional Features

66

Reservoir Rocks

Tensional Features

77

Reservoir Rocks

Ocean plate - Ocean Plate

Trench

Mountains

88

Reservoir Rocks

Ocean plate - Continental plate

��

��

��

Mid Ocean Ridge Trench

Continentalplate

Magma Magma

Mountains

Ocean plate

99

Reservoir Rocks

Continental - Continental

1010

Reservoir Rocks

Plates

1111

Reservoir Rocks

Rocks General

There are three major classes of rock:

Igneous:

(e.g. Granite).

Sedimentary:

(e.g. Sandstone).

Metamorphic:

(e.g. Marble).

1212

Reservoir Rocks

Igneous RocksComprise 95% of the Earth's crust.

Originated from the solidification of molten material from deep inside the Earth.

There are two types:

Volcanic - glassy in texture due to fast cooling.

Plutonic - slow-cooling, crystalline rocks.

1313

Reservoir Rocks

Igneous Rocks and Reservoirs

Igneous rocks can be part of reservoirs.Fractured granites form reservoirs in some parts of the world.

Volcanic tuffs are mixed with sand in some reservoirs.

1414

Reservoir Rocks

Metamorphic Rocks

2) Metamorphic rocksformed by the action of temperature and/or pressure on sedimentary or igneous rocks.

Examples are

Marble - formed from limestoneHornfels - from shale or tuffGneiss - similar to granite but

formed by metamorphosis

1515

Reservoir Rocks

Sedimentary Rocks

The third category is Sedimentary rocks. These are the most important for the oil industry as it contains most of the source rocks and cap rocks and virtually all reservoirs.

Sedimentary rocks come from the debris of older rocks and are split into two categories

Clastic and Non-clastic.

Clastic rocks - formed from the materials of older rocks by the actions of erosion, transportation and deposition.

Non-clastic rocks -from chemical or biological origin and then deposition.

1616

Reservoir Rocks

Depositional EnvironmentsThe depositional environment can be

Shallow or deep water.

Marine (sea) and lake or continental.

This environment determines many of the reservoir characteristics

1717

Reservoir Rocks

Depositional Environments 2Continental deposits are usually dunes.A shallow marines environment has a lot of turbulence hence varied grain sizes. It can also have carbonate and evaporite formation.A deep marine environment produces fine sediments.

1818

Reservoir Rocks

Depositional Environments 3

The depositional characteristics of the rocks lead to some of their properties and that of the reservoir itself.

The reservoir rock type clastic or non-clastic.The type of porosity (especially in carbonates) is determined by the environment plus subsequent events.

The structure of a reservoir can also be determined by deposition; a river, a delta, a reef and so on.

This can also lead to permeability and producibility. of these properties are often changed by further events.

1919

Reservoir Rocks

Depositional Environment 4

The environment is not static.Folding and faulting change the structure.Dissolution and fracturing can change the permeability.

2020

Reservoir Rocks

Sedimentation

Sediments settle to the bottom of the sedimentary basin.

As the sediments accumulate

the temperature and pressure increase

expelling water from the sediments.

2121

Reservoir Rocks

Sedimentation 2

Sedimentary muds become sedimentary rocks.

Calcareous muds become limestone.Sands become sandstone.

Another effect involves both the grains in the matrix and the fluids reacting to create new minerals changing the matrix and porosity. Fluids can also change creating a new set of minerals.

This whole process is called Diagenesis.

2222

Reservoir Rocks

Rock Cycle

2323

Reservoir Rocks

Clastic Rocks

Clastic rocks are sands, silts and shales. The difference is in the size of the grains.

2424

Reservoir Rocks

Depositional Environment - Delta

Sediments are transported to the basins by rivers.A common depositional environment is the delta where the river empties into the sea.A good example of this is the Mississippi.

2525

Reservoir Rocks

Rivers

Some types of deposition occur in rivers and sand bars.The river forms a channel where sands are deposited in layers. Rivers carry sediment down from the mountains which is then deposited in the river bed and on the flood plains at either side. Changes in the environment can cause these sands to be overlain with a shale, trapping the reservoir rock.

2626

Reservoir Rocks

Carbonates

Carbonates form a large proportion of all sedimentary rocks.

They consist of:Limestone.

Dolomite.

Carbonates usually have an irregular structure.

2727

Reservoir Rocks

Carbonate types

Chalk is a special form of limestone and is formed from the skeletons of small creatures (cocoliths).

Dolomite is formed by the replacement of some of thecalcium by a lesser volume of magnesium in limestone by magnesium. Magnesium is smaller than calcium, hence the matrix becomes smaller and more porosity is created.

Limestone CaCO3

Dolomite CaMg(CO3)2

Evaporites such as Salt (NaCl) and Anhydrite (CaSO4) can also form in these environments.

2828

Reservoir Rocks

Depositional Environment Carbonates

Carbonates are formed in shallow seas containing features such as:

Reefs.

Lagoons.

Shore-bars.

2929

Reservoir Rocks

Rock Properties

Rocks are described by three properties:

Porosity - quantity of pore space

Permeability - ability of a formation to flow

Matrix - major constituent of the rock

3030

Reservoir Rocks

Definition of Porosity

3131

Reservoir Rocks

Porosity Sandstones

The porosity of a sandstone depends on the packing arrangement of its grains.The system can be examined using spheres.

In a Rhombohedral packing, the pore space accounts for 26% of the total volume.

With a Cubic packing arrangement, the pore space fills 47% of the total volume.

In practice, the theoretical value is rarely reached because:

a) the grains are not perfectly round, and

b) the grains are not of uniform size.

3232

Reservoir Rocks

Porosity and Grain Size

A rock can be made up of small grains or large grains but have the same porosity.

Porosity depends on grain packing, not the grain size.

3333

Reservoir Rocks

Diagenesis

The environment can also involve subsequent alterations of the rock such as:Chemical changes.Diagenesis is the chemical alteration of a rock after burial. An example is the replacement of some of the calcium atoms in limestone by magnesium to form dolomite.

Mechanical changes - fracturing in a tectonically-active region.

3434

Reservoir Rocks

Carbonate Porosity Types 1

Interparticle porosity:

Each grain is separated, giving a similar pore space arrangement as sandstone.

Intergranular porosity:

Pore space is created inside the individual grains which are interconnected.

Intercrystalline porosity:

Produced by spaces between carbonate crystals.

Mouldic porosity:

Pores created by the dissolution of shells, etc.

Carbonate porosity is very heterogeneous. It is classified into a number of types:

3535

Reservoir Rocks

Carbonate Porosity Types 2

Fracture porosity:Pore spacing created by the cracking of the rock fabric.

Channel porosity:Similar to fracture porosity but larger.

Vuggy porosity:Created by the dissolution of fragments, but unconnected.

3636

Reservoir Rocks

Carbonate Porosity

Intergranular porosity is called "primary porosity".

Porosity created after deposition is called "secondary porosity".

The latter is in two forms:

Fractures

Vugs.

3737

Reservoir Rocks

Fractures

Fractures are caused when a rigid rock is strained beyond its elastic limit - it cracks.The forces causing it to break are in a constant direction, hence all the fractures are also aligned.

Fractures are an important source of permeability in low porosity carbonate reservoirs.

3838

Reservoir Rocks

Vugs

Vugs are defined as non-connected pore space.They do not contribute to the producible fluid total.Vugs are caused by the dissolution of soluble material such as shell fragments after the rock has been formed. They usually have irregular shapes.

3939

Reservoir Rocks

Permeability Definition The rate of flow of a liquid through a formation depends on:

The pressure drop.The viscosity of the fluid.The permeability.

The pressure drop is a reservoir property.The viscosity is a fluid property.The permeability is a measure of the ease at which a fluid can flow through a formation.

Relationships exist between permeability and porosity for given formations, although they are not universal.A rock must have porosity to have any permeability.The unit of measurement is the Darcy.Reservoir permeability is usually quoted in millidarcies, (md).

4040

Reservoir Rocks

Darcy Experiment

The flow of fluid of viscosity m through a porous medium was first investigated in 1856 by Henri Darcy.He related the flow of water through a unit volume of sand to the pressure gradient across it.In the experiment the flow rate can be changed by altering the parameters as follows:

4141

Reservoir Rocks

Darcy Law

K = permeability, in Darcies.L = length of the section of rock, in centimetres.Q = flow rate in centimetres / sec.P1, P2 = pressures in bars.A = surface area, in cm2.µ = viscocity in centipoise.

4242

Reservoir Rocks

Permeability and Rocks

In formations with large grains, the permeability is high and the flow rate larger.

4343

Reservoir Rocks

Permeability and Rocks 2

In a rock with small grains the permeability is less and the flow lower.

Grain size has no bearing on porosity, but has a large effect on permeability.

4444

Reservoir Rocks

Reservoir Rocks

Reservoir rocks need two properties to be successful:Pore spaces able to retain hydrocarbon.Permeability which allows the fluid to move.

4545

Reservoir Rocks

Clastic Reservoirs

Sandstone usually has regular grains; and is referred to as a grainstone.

PorosityDetermined mainly by the packing and mixing of grains.

PermeabilityDetermined mainly by grain size and packing, connectivity and shale content.

Fractures may be present.

4646

Reservoir Rocks

Carbonate Reservoirs

Carbonates normally have a very irregular structure.

Porosity:Determined by the type of shells, etc. and

by depositional and post-depositional events(fracturing, leaching, etc.).

Permeability:Determined by deposition and post-deposition events, fractures.

Fractures can be very important in carbonate reservoirs.

4747

Reservoir Rocks

Cap Rock

A reservoir needs a cap rock.

Impermeable cap rock keeps the fluids trapped in the reservoir.It must have zero permeability.Some examples are:

Shales.Evaporites such as salt or anhyhdrite.Zero-porosity carbonates.

4848

Reservoir Rocks

Source RocksHydrocarbon originates from minute organisms in seas and lakes. When they die, they sink to the bottom where they form organic-rich "muds" in fine sediments.These "muds" are in a reducing environment or "kitchen", which strips oxygen from the sediments leaving hydrogen and carbon.The sediments are compacted to form organic-rich rocks with very low permeability.The hydrocarbon can migrate very slowly to nearby porous rocks, displacing the original formation water.

4949

Reservoir Rocks

Temperature Window

If the temperature is too low, the organic material cannot transform into hydrocarbon.If the temperature is too high, the organic material and hydrocarbons are destroyed.

5050

Reservoir Rocks

Hydrocarbon Migration

Hydrocarbon migration takes place in two stages:Primary migration - from the source rock to a porous rock. This is a complex process and not fully understood.It is probably limited to a few hundred metres.

Secondary migration - along the porous rock to the trap.This occurs by buoyancy, capillary pressure and hydrodynamics through a continuous water-filled pore system.

It can take place over large distances.

5151

Reservoir Rocks

Rock Classification

ClasticsRock type Particle diameter

Conglomerate Pebbles 2 - 64mmSandstone Sand .06 - 2mmSiltstone Silt .003 - .06mmShale Clay <.003mm

Non-ClasticsRock type Composition

Limestone CaCO3Dolomite CaMg(CO3)2Salt NaClAnhydrite CaSO4Gypsum CaSO4.2H2OCoal Carbon

5252

Reservoir Rocks

Reservoir Structure

There are many other types of structure.The criteria for a structure is that it must have:

Closure, i.e. the fluids are unable to escape.Be large enough to be economical.

The exact form of the reservoir depends on the depositional environment and post depositional events such as foldings and faulting.

5353

Reservoir Rocks

Traps General

5454

Reservoir Rocks

Structural TrapsThe simplest form of trap is a dome.This is created by upward movement or folding of underlying sediments.

An anticline is another form of simple trap. This is formed by the folding of layers of sedimentary rock.

5555

Reservoir Rocks

Fault TrapsFaults occur when the rock shears due to stresses. Reservoirs often form in these fault zones.A porous and permeable layer may trap fluids due to its location alongside an impermeable fault or its juxtaposition alongside an impermeable bed.Faults are found in conjunction with other structures such as anticlines, domes and salt domes.

5656

Reservoir Rocks

Salt Dome TrapSalt Dome traps are caused when "plastic" salt is forced upwards.The salt dome pierces through layers and compresses rocks above. This results in the formation of various traps:In domes created by formations pushed up by the salt.Along the flanks and below the overhang in porous rock abutting on the impermeable salt itself.

5757

Reservoir Rocks

Stratigraphic Traps

5858

Reservoir Rocks

Reservoir Mapping

Reservoir contours are usually measured to be below Mean Sea Level (MSL).They can represent either the reservoir formation structure or fluid layers.

11

Reservoir Fluids

Reservoir Fluids


22

Reservoir Fluids

Definitions

Oil in Place OIP The volume of oil in the

reservoir in barrels or cubic metres.

Gas/Oil Ratio GOR The gas content of the oil.

API Gravity API Oil gravity.

Fluid Contacts

33

Reservoir Fluids

Fluids in a Reservoir

A reservoir normally contains either water or hydrocarbon or a mixture.

The hydrocarbon may be in the form of oil or gas.

The specific hydrocarbon produced depends on the reservoir pressure and temperature.

The formation water may be fresh or salty.

The amount and type of fluid produced depends on the initial reservoir pressure, rock properties and the drive mechanism.

44

Reservoir Fluids

Hydrocarbon Composition

Typical hydrocarbons have the following composition in Mol Fraction

Hydrocarbon C1 C2 C3 C4 C5 C6+

Dry gas .88 .045 .045 .01 .01 .01

Condensate .72 .08 .04 .04 .04 .08

Volatile oil .6-.65 .08 .05 .04 .03 .15-.2

Black oil .41 .03 .05 .05 .04 .42

Heavy oil .11 .03 .01 .01 .04 .8

Tar/bitumen 1.0

The 'C' numbers indicated the number of carbon atoms in the molecular chain.

55

Reservoir Fluids

Hydrocarbon Structure

The major constituent of hydrocarbons is paraffin.

66

Reservoir Fluids

Hydrocarbon ClassificationHydrocarbons are also defined by their weight and the Gas/Oil ratio. The table gives some typical values:

GOR API Gravity

Wet gas 100mcf/b 50-70

Condensate 5-100mcf/b 50-70

Volatile oil 3000cf/b 40-50

Black oil 100-2500cf/b 30-40

Heavy oil 0 10-30

Tar/bitumen 0 <10

The specific gravity of an oil is defined as:

77

Reservoir Fluids

Hydrocarbon Gas

Natural gas is mostly (60-80%) methane, CH4. Some heavier gases make up the rest.

Gas can contain impurities such as Hydrogen Sulphide, H2S and Carbon Dioxide, CO2.

Gases are classified by their specific gravity which is defined as:

"The ratio of the density of the gas to that of air at the same temperature and pressure".

88

Reservoir Fluids

Reservoir Pressure

Reservoir Pressures are normally controlled by the gradient in the aquifer.High pressures exist in some reservoirs.

99

Reservoir Fluids

Reservoir Pressure Calculation

1010

Reservoir Fluids

Reservoir Pressure Example

1111

Reservoir Fluids

Reservoir Temperature Gradient

The chart shows three possible temperature gradients. The temperature can be determined if the depth is known.

High temperatures exist in some places. Local knowledge is important.

1212

Reservoir Fluids

Fluid Phases

A fluid phase is a physically distinct state, e.g.: gas or oil.

In a reservoir oil and gas exist together at equilibrium, depending on the pressure and temperature.

The behaviour of a reservoir fluid is analyzed using the properties; Pressure, Temperature and Volume (PVT).

There are two simple ways of showing this:Pressure against temperature keeping the volume constant.

Pressure against volume keeping the temperature constant.

1313

Reservoir Fluids

PVT Experiment

1414

Reservoir Fluids

Phase Diagram -single component

The experiment is conducted at different temperatures.The final plot of Pressure against Temperature is made.The Vapour Pressure Curve represents the Bubble Point and Dew Point. (For a single component they coincide.)

1515

Reservoir Fluids

Phase diagram OilThe Pressure/Temperature (PT) phase diagram for an oil reservoir:Point 'A' is the initial reservoir condition of pressure and

temperature.If the reservoir is produced at a constant temperature

until the fluid reaches the wellbore, the line to Point 'B' is drawn. This represents the flow of fluid from the reservoir to the borehole. The fluid travelling to surface now drops in both temperature and pressure arriving at he "separatorconditions" (s) with a final volume of oil and gas.

1616

Reservoir Fluids

Phase Diagram Condensate/Gas

Point 'C' is at the initial reservoir conditions. The reservoir is produced at a constant temperature from C to D. Fluids flowing up the well now drop in temperature and pressure, crossing the Dew point line and liquid condenses out.

At separator conditions (s) the result in both liquid and gas on the surface.

1717

Reservoir Fluids

Gas Reservoir

In a gas reservoir the initial point is A. Producing the well to separator conditions B does not change the fluid produced.

The point B is still in the "gas region" and hence dry gas is produced.

1818

Reservoir Fluids

Hydrocarbon Volumes

Fluids at bottom hole conditions produce different fluids at surface:Oil becomes oil plus gas.Gas usually stays as gas unless it is a Condensate.Water stays as water with occasionally some dissolved gas.

1919

Reservoir Fluids

FVF Oil and Gas

There is a change in volume between downhole conditions and the surface.

The volume of the fluid at reference conditions is described by the Formation Volume Factor:

FVF =

Bo = formation volume factor for oil.Bw = formation volume factor for water.Bg = formation volume factor for gas.

Volume at downhole Conditions

Volume at reference Conditions

2020

Reservoir Fluids

Saturation

Formation saturation is defined as the fraction of its pore volume (porosity) occupied by a given fluid.

Saturation =

DefinitionsSw = water saturation.So = oil saturation.Sg = gas saturation.Sh = hydrocarbon saturation = So + Sg

Saturations are expressed as percentages or fractions, e.g. Water saturation of 75% in a reservoir with porosity of 20% contains water equivalent to 15% of its volume.

Volume of a specific fluid pore volume

2121

Reservoir Fluids

Saturation Definition

2222

Reservoir Fluids

Wettability

The wettability defines how a fluid adheres to the surface (or rock in the reservoir) when there are two fluids present, e.g. water and air.

The angle measured through the water is the "contact angle".

If it is less than 90° the rock is water wet; greater than 90° the rock is oil wet.

Most reservoir rocks are water wet.

2323

Reservoir Fluids

Irreducible Water Saturation

In a formation the minimum saturation induced by displacement is where the wetting phase becomes discontinuous.In normal water-wet rocks, this is the irreducible water saturation, Swirr.Large grained rocks have a low irreducible water saturation compared to small-grained formations because the capillary pressure is smaller.

2424

Reservoir Fluids

Capillary Forces

In a simple water and air system the wettability gives rise to a curved interface between the two fluids.

This experiment has a glass tube attached to a reservoir of water. The water "wets" the

glass. This causes the pressure on the concave side (water) to exceed that on the convex side (air). This excess pressure is the capillary pressure.

Pc = capillary pressure.σσσσ = surface tension.q = contact angle. rcap = radius of capillary tube.

2525

Reservoir Fluids

Capillary Forces and Rocks

In a reservoir the two fluids are oil and water which are immiscible hence they exhibit capillary pressure phenomena.This is seen by the rise in the water above the point where the capillary pressure is zero.

The height depends on the density difference and the radius of the capillaries.

2626

Reservoir Fluids

Transition Zone

The phenomenon of capillary pressure gives rise to the transition zone in a reservoir between the water zone and the oil zone.The rock can be thought of as a bundle of capillary tubes.The length of the zone depends on the pore size and the density difference between the two fluids.

2727

Reservoir Fluids

Relative Permeability

Take a core 100% water-saturated. (A)Force oil into the core until irreducible water saturation is attained (Swirr). (A-> C -> D)Reverse the process: force water into the core until the residual saturation is attained. (B)During the process, measure the relative permeabilities to water and oil.

2828

Reservoir Fluids

Relative Permeability Experiment

2929

Reservoir Fluids

Drive Mechanisms

A virgin reservoir has a pressure controlled by the local gradient.Hydrocarbons will flow if the reservoir pressure is sufficient to drive the fluids to the surface (otherwise they have to be pumped).As the fluid is produced reservoir pressure drops.The rate of pressure drop is controlled by the Reservoir Drive Mechanism.Drive Mechanism depends on the rate at which fluid expands to fill the space vacated by the

produced fluid.Main Reservoir Drive Mechanism types are:

Water drive.

Gas cap drive.

Gas solution drive

3030

Reservoir Fluids

Water Invasion 1

Water invading an oil zone, moves close to the grain surface, pushing the oil out of its way in a piston-

like fashion.

The capillary pressure gradient forces water to move ahead faster in the smaller pore channels.

3131

Reservoir Fluids

Water Invasion 2

The remaining thread of oil becomes smaller.

It finally breaks into smaller pieces.

As a result, some drops of oil are left behind in the channel.

3232

Reservoir Fluids

Water Drive

Water moves up to fill the "space" vacated by the oil as it is produced.

3333

Reservoir Fluids

Water Drive 2

This type of drive usually keeps the reservoir pressure fairly constant.After the initial “dry” oil production, water may be produced. The amount of produced water increases as the volume of oil in the reservoir decreases. Dissolved gas in the oil is released to form produced gas.

3434

Reservoir Fluids

Gas Invasion

Gas is more mobile than oil and takes the path of least resistance along the centre of the larger channels.As a result, oil is left behind in the smaller, less

permeable, channels.

3535

Reservoir Fluids

Gas Cap Drive

Gas from the gas cap expands to fill the space vacated by the produced oil.

3636

Reservoir Fluids

Gas Cap Drive 2

As oil production declines, gas production increases.

Rapid pressure drop at the start of production.

3737

Reservoir Fluids

Solution Gas Drive

After some time the oil in the reservoir is below the bubble point.

3838

Reservoir Fluids

Solution Gas Drive 2

An initial high oil production is followed by a rapid decline.The Gas/Oil ratio has a peak corresponding to the higher permeability to gas. The reservoir pressure exhibits a fast decline.

3939

Reservoir Fluids

Drives General

A water drive can recover up to 60% of the oil in place.A gas cap drive can recover only 40% with a greater reduction in pressure.A solution gas drive has a low recovery.

4040

Reservoir Fluids

Drive Problems

Water Drive:Water can cone upwards and be produced through the lower perforations.

Gas Cap Drive:Gas can cone downwards and be produced through the upper perforations.Pressure is rapidly lost as the gas expands.

Gas Solution Drive:Gas production can occur in the reservoir, skin damage.Very short-lived.

4141

Reservoir Fluids

Secondary Recovery 1

Secondary recovery covers a range of techniques used to augment the natural drive of a reservoir or boost production at a later stage in the life of a reservoir.A field often needs enhanced oil recovery (EOR)

techniques to maximise its production.Common recovery methods are:

Water injection.Gas injection.

In difficult reservoirs, such as those containing heavy oil, more advanced recovery methods are used:

Steam flood.Polymer injection. .CO2 injection.In-situ combustion.

4242

Reservoir Fluids

Secondary Recovery 2 water injection

gas injection

11

Spontaneous Potential Measurement

Spontaneous Potential


22


SP Theory 1

SP results from electric currents flowing in the drilling mud.

There are three sources of the currents, two electrochemical and one electrokinetic.

Membrane potential - largest.

Liquid - junction potential.

Streaming potential - smallest.

33


SP theory 2

Membrane and Liquid Potential

These two effects are the main components of the SP. They are caused because the mud flitrate and the formation waters containNaCl in different proportions. Firstly, shales are permeable to the Sodium ions but not

the Chlorine. Hence there is a movement of charged particles through the shale creating a current and thus a potential.The ions Na+ and Cl- have different mobilities at the junction of the invaded and virgin zones. The movement of the ions across this boundary creates another current and hence a potential.

Streaming Potential

This is generated by flow of the mud filtrate through the mud cake. As this does not normally occur this effect is small. It will only become important if there are high differential pressures across the formations.

44


SP theory 3

55


SP scales

The SP is measured in millivolts, mV.

The scale on the log shows a number of mV per division for example 20mV/division. This gives a total for the track of 200mV.

The scale across the track is variable and depends on the conditions in the well.

The scale is set during logging to have the SP curve in the track over the zone of interest and as much of the rest of the log as possible.

66


log-1

The SSP is the quantity to be determined.

It is the deflection seen on the SP from the Shale Base Line (zero point) to the Sand Line (max. deflection)

77


example log 2

The maximum SP deflection in this example occurs at the same depths as the resistivity curves show a separation.The minimum point on the SP corresponds to where all the resistivity curves overlay, no invasion, a shale.

88


SP uses

Differentiate potentially porous and permeable reservoir rocks from impermeable clays.

Define bed boundaries.

Give an indication of shaliness (maximum deflection is clean; minimum is shale).

Determine Rw in both salt and fresh muds.

99


Rw from the SP

Rw is often known from client information or local knowledge.

The SP can be used to check the value or compute it when it is unavailable.

It is especially useful when there are variations along the borehole.

K is a constant - depending on the temperature.

we

mfe

RR

kSSP log−=

1010


Rw from the SP

Knowing the SSP (the maximum deflection) from the log and the temperature, the ratio of resistivities is obtained from Log Interpretation Chart SP-1.output = Rmfe

Rwe

1111


Rw from SP 2

Rmf is measured, using the mud cell.Rmfe is computed from Log Interpretation Chart SP-2.Rwe is computed, from the ratio from SP1 and Rmfe.Chart SP-2 output is Rw.

1212


Salinities chart

This chart is used to compute salinities from resistivities of solution e.g. mud, and vice versa.It is also used to find the resistivities at a given temperature.

0.1

0.2

0.3

0.4

0.5

0.6

0.8

1

2

3

4

56

8

10

0.08

0.060.05

0.04

0.03

0.02

0.01

50 75 100 125 150 200 250 300 350 400

10

15

20

2530

40

50

100

150

200

250300

400

500

1000

1500

200025003000

40005000

10,000

15,00020,000

280,000

200

300

400

500

600

700

800

1000

1200

1400

1700

2000

3000

4000

5000

6000

70008000

10,000

12,000

14,000

17,000

20,000

250,000 200,000 170,000 140,000 120,000 100,00080,000 70,000 60,000 50,00040,00030,000

300,000

10 20 30 40 50 60 70 140 160 20080 90 100 120 180

ppm

Gra

ins/

gal

at 7

5ÞF

Res

istiv

ity o

f Sol

utio

n (ž

- m

)

Temperature (ÞF or ÞC)

NaC

l Con

cent

ratio

n (p

pm o

r gra

ins/

gal)

1313


SP borehole Effects - 1

Baseline shifts:

These can occur when there are beds of different salinities separated by a shale which does not act as a perfect membrane.

1414


SP Borehole Effects - 2

Resistive formation:The presence of a resistive bed in a permeable interval will disrupt the SP deflection. The current is contained and hence the potential drop changes with depth. The log takes a sloped appearance.

The log in this situation can no longer define the bed boundaries correctly.

1515


SP surface Effects

The SP can be affected by a number of surface effects as it relies on the fish as its reference electrode.Power lines, electric trains, electric welding, close radio transmitters:All these create ground currents which disrupt he "fish" reference causing a poor, sometimes useless, log.

11

Gamma Ray Measurement



22


Gamma Ray Principles

The Gamma Ray log is a measurement of the formation's natural radioactivity.

Gamma ray emission is produced by three radioactive series found in the Earth's

crust.

Potassium (K40) series.

Uranium series.

Thorium series.

Gamma rays passing through rocks are slowed and absorbed at a rate which depends on the formation density.

Less dense formations exhibit more radioactivity than dense formations even though there may be the same quantities of radioactive material per unit volume.

33


Basic Gamma Ray Uses

Bed definition:The tool reacts if the shale is radioactive (usually the case), hence show the sands and shales, the permeable zones and the non-permeable zones.

Computation of the amount of shale:

The minimum value gives the clean (100%) shale free zone, the maximum 100% shale zone. All other points can then be calibrated in the amount of shale.

44


GR Uses

The gamma ray log is used for:

Lithology/mineralogy, e.g. shaliness.

Correlation:A major use of the tool is to identify marker beds and thus allow well-to-well correlation. Marker beds can be the top or bottom of the reservoir or a specific shale giving a high reading.

Subsidence logging:Radioactive bullets are placed accurately spaced in the

formation. A gamma ray tool with a number of precisely spaced detectors is logged and the peaks noted. Subsequent logs will show any movement.

Tracer logging:A radioactive fluid is ejected by a tool at a chosen level. The fluid movement is monitored by the gamma ray and will show thief zones and channels in the cement behind the casing.

55


NGT

The NGT tool measures a spectrum that is the result of the three naturally occurring radioactive series.

The Potassium has a sharper shape than the other two as it decays through a single reaction to a stable element. The other two decay through a number of daughter elements each with some contribution to the final picture.

66


NGT Principle

The measurement in the standard tool is made by a measurement in a number of fixed energy windows. Three of these at the highest levels are set over a characteristic peak of each of the elements.The statistical nature of the measurement is partly improved by using another two windows set at a lower energy which has a higher rate.

77


NGT Log

Outputs are the relative amounts of Thorium, Uranium and Potassium in the formation.With:

Thorium in ppm.Uranium in ppm.Potassium in %.

Additional curves are the total gamma ray (SGR) and a Uranium-corrected gamma ray (CGR).

88


NGT uses

This tool has many applications:

Lithology identification.Study of depositional environments.Investigation of shale types.Correction of the GR for clay content evaluation.Identification of organic material and source rocks.Fracture identification.Geochemical logging.Study of a rock's diagenetic history.

A major application was to solve North Sea log interpretation problems in micaceous sands.

99


NGT uses

The three radioactive elements measured by the NGT occur in different parts of the reservoir. If we know the lithology, we can obtain further information.

In Carbonates:

U - indicates phosphates, organic matter and stylolites.

Th - indicates clay content.

K - indicates clay content, radioactive evaporites.

1010


NGT in Clastics

In Sandstones:

Th - indicates clay content, heavy minerals.

K - indicates micas, micaceous clays and feldspars.

In Shales:

U - in shale, suggest a source rock.

Th - indicates the amount of detrital material or degree of shaliness.

K - indicates clay type and mica.

1111


NGT Crossplots - 1The NGT data is interpreted using three major crossplots. In order of complexity:

Thorium versus Potassium:

Gives clay type

Photoelectric factor, Pe, versus Potassium:

Gives clay type and micas.

Pe versus Thorium/Potassium ratio:

Gives clay type and micas.

1212


NGT Crossplots - 2

This plot can be used to determine the type of clay mineral or mica.

1313


NGT Crossplots - 3

This plot adds in the Thorium contribution making it more precise than the previous one.

1414


NGT/GR parametersVertical resolution 18"

Depth of investigation 6"-8"

Readings in: API units

Limestone <20Dolomite <30Sandstone <30Shale 80-300Salt <10Anhydrite <10

No formation is perfectly clean, hence the GR readings will vary. Limestone is usually cleaner than the other two

reservoir rocks and normally has a lower GR.

1515


GR/NGT Limits

GR

- Organic materials (see the uranium as "shale").- Micas (sees micaceous sands as shaly).

NGT

- Barite in the mud (reduces the count rate but can be partially corrected for).- KCI mud (Potassium in the mud masks the formation response but can be partially corrected for).- Large boreholes decrease the count rate hence increase the statistics.- Statistical errors.

1616


GR Correction 1

GR logs require correction for the effects of the mud.

1717


GR Correction 2

An additional correction is needed if there is mud in the borehole.

11

Neutron Porosity Measurement

Neutron Porosity


22


Lithology and Porosity

The next major step in the procedure is lithology identification. Lithology data gives information on porosity and other parameters.

Lithology of a formation can be:

Simple

Dirty

Complex

33


Lithology and Porosity Tools

All tools react to lithology - usually in conjunction with the porosity.

Major lithology tools are:

Neutron - reacts to fluid and matrix.

Density - reacts to matrix and fluid.

Sonic - reacts to a mixture of matrix and fluid, complicated by seeing only primary

porosity.

NGT - identifies shale types and special minerals.

CMR - magnetic resonance reacts to the porosity with a small element if lithology.

44


Neutrons

55


Early Neutron Tools

The first neutron tools used a chemical neutron source and employed a single detector which measured the Gamma Rays of capture

They were non-directional.

The units of measurement were API units where 1000 API units were calibrated to read 19% in a water-filled limestone.

The tool was badly affected by the borehole environment.

66


Neutron Tools

The second generation tool was the Sidewall Neutron Porosity (SNP).

This was an epithermal device mounted on a pad.

The current tool is the Compensated Neutron Tool (CNT).

The latest tool is the Accelerator Porosity Sonde (APS), using an electronic source for the neutrons and measuring in the epithermal region.

77


Hydrogen Index

Hydrogen Index is the quantity of hydrogen per unit volume.

Fresh water is defined as having a Hydrogen Index of 1.Hence oil has a Hydrogen Index which is slightly less than that of water.

The Hydrogen Index of gas is a much smaller than that of water.

In a formation, it is generally the fluids that contain hydrogen.

88


Thermal Neutron Theory

Neutrons are slowed down from their initial "fast" state by collisions with the formation nuclei. At each collision there is some energy lost by the neutron.

The principal element involved in the slowing down is Hydrogen, because it is close in size to the neutron which loses most energy in these collisions.The CNT measures the neutron population in the thermal region.This is why the tool measures the Hydrogen Index.

99


DetectorsTwo neutron detectors are used to produce a ratio eliminating some of the borehole effects experienced by single detectors.The count rate for each detector is inversely proportional to porosity with high porosity giving low count rates.

1010


Ratio to Porosity Transform

The count rates are first corrected for the dead time of the detectors (when the detector is not available to receive counts).

The count rates are calibrated with the master calibration.

A ratio of these is then taken.

The ratio is translated into porosity using a transform. (This is a combination of theoretical and experimental work).

The current field output for the thermal neutron porosity is called TNPH.

1111


Borehole Effects

The logs have to be corrected for the borehole environment:

Borehole size.

Mud cake.

Borehole salinity.

Mud weight.

Temperature.

Pressure.

Formation salinity.

Stand-off.

1212


Hole Size Correction

Necessary because the tools algorithm from ratio to porosity is built to "fit" a 77/8" hole.Larger holes cause the tool to see more mud (100% porosity) around the borehole, hence the tool reads too high in larger hole sizes.

The chart is entered with the porosity;

Go down to hole size.Follow trend lines to 7 7/8".Read of ∆φ∆φ∆φ∆φ.

A correction is made automatically in open hole using caliper measurements from the combined density tool.It can be made using the bit size if a caliper is not available.The correction can be large.

1313


Mud Cake Correction

The mud cake absorbs neutrons before they can enter or leave the formation.mud cake = stand-off with porosity <100%.The larger the mud cake, the larger the correction.It is a small correction but one that is rarely ever applied because the mud cake cannot be easily measured.

1414


Borehole Salinity Correction

This arises due to Chlorine.The more Chlorine present, the more neutrons

absorbed in the borehole. ==> decrease count rate.The largest effect is seen in salt-saturated muds.

Go down to the borehole salinity.Follow trend lines to zero.Read ∆φ∆φ∆φ∆φ.

1515


Mud Weight Correction

The extra material in heavier muds means there is less hydrogen, hence more neutrons reach the formation.It also changes if the mud is full of barite.

In this case the amount of material needed to achieve the same mud weight is less, hence the correction is less.

Select normal or barite mud.Enter with porosity.Go down to mud weight.Follow lines to 8 lb/gal.Read ∆φ∆φ∆φ∆φ.

The correction is quite small.

1616


Formation Temperature Correction

The correction is large and depends on the porosity.This is a dual effect:

The expansion of the water reduces the quantity of Hydrogen seen by the tool.Change in the borehole fluid capture cross-section.

Enter with porosity at the top.Go down to hole temperature.Follow trend lines to 75ÞF.Read ∆φ∆φ∆φ∆φ.

1717


Pressure Correction

The effect is caused by the compression of the fluids downhole.In standard water-based muds the effect is small.

Select oil-based or water-based mud.Enter with porosity at the top.Go down to hole pressure.Follow trend lines to zero.Read ∆φ∆φ∆φ∆φ.

In oil-based muds the correction is large.

1818


Formation/Salinity Correction

There are two factors affecting the neutron measurement in the formation:

The chlorine in the formation water.The rock matrix capture cross-section.

The simplest method is to assume that the matrix is clean and that the matrix 'ΣΣΣΣ' known.This leaves salinity (mud filtrate) as the only "variable".

The complete solution is to measure the total formation 'ΣΣΣΣ' and use this to compute the correction.The correction can be large but is not applied in the field because the lithology is unknown, hence the 'ΣΣΣΣ' unknown.It is taken into account in the interpretation phase.

1919


Stand off Correction

Any space between the tool and the borehole wall is seen as 100% porosity.The value of the correction depends on the hole size:Larger holes = more correctionStand-off is rarely measured. One method is to use the SA curve recorded with a PCD.

The chart is entered with the porosity at the top;

Go to the nearest hole size.Go down to the stand-off value, e.g. 0.5".Follow the lines to zero.Read the ∆φ ∆φ ∆φ ∆φ (always negative).

2020


Standoff Correction Chart

2121


Alpha Processing

Alpha Processing is a method that enhances the resolution of the standard measurement.

It utilizes the higher resolution of the near detector to increase the resolution of the more accurate far detector.

2222


Alpha Processing

The first step is to depth-match the two detectors' responses.

The next step is to match the resolution of both detectors.

2323


Alpha Processing

The difference between the two readings now gives the "high frequency" information - which highlights thin beds missed by the far detector.

2424


Alpha processing

The "high frequency" information is added to the far detector signal to give the final enhanced log.

2525


Thermal Neutron Parameters

Vertical resolution:Standard (TNPH) 24"Enhanced 12"


Readings in zero porosity:

Limestone (0%) 0Sandstone (0%) -2.00Dolomite (0%) 1.00Anhydrite -2.00Salt -3.00

Typical Readings

Shale 30-45Coal 50+

2626


Thermal Neutron Interpretation/Uses

The tool measures hydrogen index.

Its prime use is to measure porosity.

Combined with the bulk density, it gives the best possible answer for lithology and porosity

interpretation.

2727


Thermal Neutron in Cased Hole

The CNT can be run in cased hole for the porosity.

In addition to the standard corrections some others are needed to take into account the extra elements of casing and cement.

The standard conditions are:

83/4" borehole diameter.Casing thickness 0.304".Cement thickness 1.62".Fresh water in the borehole / formation.No stand-off.75ÞF.Atmospheric pressure.Tool eccentred in the hole.

2828


Corrections in Cased Hole

11

Bulk Density Measurement



22


Gamma Ray Physics -density -1

The Density Tools use a chemical gamma ray source and two or three gamma ray detectors.

The number of gamma rays returning to the detector depends on the number of electrons present, the electron density, ρρρρe.The electron density can be related to the bulk density of the minerals by a simple equation.

ρρρρe = ρρρρ( 2Z/A )

Where Z is the number of electrons per atomand A is the atomic weight.

33


Gamma Ray Physics -density 2

The assumption made in the interpretation is that:

Z/A = 0.5

This is very close for most elements commonly encountered, except hydrogen which has

little effect on the measurement. Therefore ρρρρe = ρρρρ

Element Z/AH 0.9921C 0.4996O 0.5Na 0.4785Mg 0.4934Al 0.4819Si 0.4984S 0.4989Cl 0.4794K 0.4860Ca 0.499

44


Calibration

The tool measured density, ρρρρb, has been experimentally related to the electron density;

ρρρρb = 1.0704 ρρρρe - 0.1883

The tool needs to be calibrated in a known condition.This condition is fresh water and limestone, densities, 1.00 and 2.71 respectively.

The bulk density versus the electron density equation fits for all the common minerals with a few exceptions:Salt - true density 2.165

density tool value 2.03

Sylvite - true density 1.984density tool value 1.862

55


Spine and Ribs

The spine represents the line of increasing formation density on the plot of the long spacing count rate versus short spacing count rate.

The presence of mud cake causes a deviation from the line in a predictable manner. Thus a correction can be made to obtain the true density.

.

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

Mud cakewith barite

Mud cakewithoutbarite

IncreasingMud cakeThickness


A

B

C

Lon

g Sp

acin

g C

ount

Rat

e

Short spacing Count Rate

66


Spine and Ribs

Example:The correct reading is at point A.An increasing mud cake thickness moves the point to B or C depending on whether there is heavy material (barite) in the mud or not.

.

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

Mud cakewith barite

Mud cakewithoutbarite



A

B

C

Lon

g Sp

acin

g C

ount

Rat

e

Short spacing Count Rate

77


Density Outputs

The outputs are:RHOZ/RHOB (ρρρρb), the corrected bulk density.

DRHO (∆ρ∆ρ∆ρ∆ρ), the correction that has beenapplied to ρρρρb (LDT only).

RHOZ/RHOB is the main output;

DRHO is a quality control curve (LDT only).

88


Borehole Effects

The LDT is a pad tool with collimated source and detectors. It experiences little or no environmental effect.

In large holes, the curvature of the pad versus that of the hole causes a minor error that needs to be corrected.

99


Borehole Effects

Hole rugosity may affect the measurement.

The source and detectors "see" different formations/borehole.

The effect is an erratic and incorrect log.

1010


Alpha Processing

As the density tool also uses two detectors it can be Alpha processed in exactly the same way as the CNT.

The resulting log shows a great improvement over the standard output.

1111


Density Parameters

Vertical resolution:

Standard 18"Enhanced 6"


Readings in:

Limestone (0pu) 2.71Sandstone (0pu) 2.65Dolomite (0pu) 2.85Anhydrite 2.98Salt 2.03Shale 2.2-2.7Coal 1.5

1212


Interpretation/Uses

The density tool is extremely useful as it has high accuracy and exhibits small borehole effects.

Major uses include:Porosity.

Lithology (in combination with the neutron tool).

Mechanical properties (in combination with the sonic tool).

Acoustic properties (in combination with the sonic tool).

Gas identification (in combination with the neutron tool).

1313


Density Porosity

There are two inputs into the porosity equation: the matrix density and the fluid density.

The fluid density is that of the mud filtrate.

(((( ))))φφφφρρρρφφφφρρρρρρρρ −−−−++++==== 1mafb

fma

bma

ρρρρρρρρρρρρρρρρφφφφ

−−−−−−−−====

1414


Scaling/PorosityThe density tool is usually run with the neutron.To aid quicklook interpretation they are run on

"compatible scales".This means that the scales are set such that for a given lithology the curves overlay.The standard scale is the "limestone compatible" where

the neutron porosity scale is:

To fit this the density log has to have its zero limestone point (2.7 g/cc) on the same position as the neutron porosity zero and the range of the scale has to fit the neutrons 60 porosity units hence the scale is:

Changing to a sandstone compatible scale would put the zero sandstone density, 2.65, over the neutron porosity zero to give:

1515


Pef Physics

The Photoelectric effect occurs when the incident gamma ray is completely absorbed by the

electron.

It is a low energy effect hence the Photoelectric Absorption index, Pe, is measured using

the lowest energy window of the tool.

Pe is related directly to Z, the number of electrons per atom, hence fixed for each element.

Pe = ( Z/A )3.6

Its units are barns/electron.

1616


Pef Theory

Pe can be easily computed for any lithology by summing the elemental contributions.

Measurement is virtually porosity and fluid independent.

Major use is Lithology identification.Another way of using it is express it in volumetric terms as:

U = Peρρρρe

This is called the Volumetric photoelectric absorption index.This parameter can then be used in a formula for computing the components of the reservoir.

U = φφφφUf + (1 - φφφφ) Uma

1717


Pef Parameters


Standard 4"

Readings in:

Limestone 5.08Sandstone 1.81Dolomite 3.14Shale 1.8-6Anhydrite 5.05Salt 4.65

11

Sonic Measurement

Sonic Measurement


22

Sonic Measurement

Sonic ToolThe sonic tools create an acoustic signal and measure how long it takes to pass through a rock.

By simply measuring this time we get an indication of the formation properties.

The amplitude of the signal will also give information about the formation.

33

Sonic Measurement

sonic borehole waves

44

Sonic Measurement

waves 2

In a fast formation both compressional and shear waves are created.

The head waves in the borehole are the signals seen by the receivers.

The array of receivers see the signal at different times as they are at different distances from the transmitter.

55

Sonic Measurement

Sonic -BHC

A simple tool that uses a pair of transmitters and four receivers to compensate for caves and sonde tilt.

The normal spacing between the transmitters and receivers is 3' - 5'.

It produces a compressional slowness by measuring the first arrival transit times.

Used for:Correlation.Porosity.Lithology.Seismic tie in /time-to-depth conversion.

66

Sonic Measurement

Long Spacing Sonic

The BHC tool is affected by near borehole altered zones hence a longer spacing is needed with a larger depth of investigation.

The tool spacings are 8' - 10', 10' - 12'.

The tool cannot be built with transmitters at each end like a BHC sonde, hence there are two transmitters at the bottom.

A system called DDBHC - depth derived borehole compensation, is used to compute the transmit time.

The uses of this tool are the same as the BHC tool.

77

Sonic Measurement

Array SonicMulti-spacing digital tool.

First to use STC processing.

Able to measure shear waves and Stoneley waves in hard formations.

Used for:Porosity.Lithology.Seismic tie in / time-to-depth conversion.Mechanical properties (from shear and compressional).Fracture identification (from shear and Stoneley).Permeability (from Stoneley).

88

Sonic Measurement

DSI General

In a slow formation the shear wave from a monopole source never creates a head wave. The fluid wave is the first arrival after the compressional.

A dipole source is directional.

It creates a flexural wave on the borehole wall and shear and compressional in the formation.

The shear wave is recorded whether the formation is soft or hard.

99

Sonic Measurement

DSI tool

Generates both monopole and dipole signals.Generates different frequencies for measuring a range of waves.

Measures:Compressional and shear Two orthogonal shear - dipole signalsStoneley

Application:Seismic.Mechanical properties (from shear and

compressional).Fracture identification (shear and

Stoneley).Permeability computation (Stoneley).Porosity / Lithology.Gas shows.

1010

Sonic Measurement

STC Processing

This type of processing is necessary to extract the shear and Stoneley information from the waveform.The processing applies a "semblance algorithm" to the recorded set of traces.

This means looking for the same part of the wave (e.g. shear) on each wavetrain.

Once this has been done the transit time can be computed.

1111

Sonic Measurement

STC Map

At a given depth, the slowness can be plotted against time.Regions of large coherence appear as contours.

These correspond to the compressional (fastest), shear (close to the compressional) and Stoneley (furthest away).

1212

Sonic Measurement

STC Output

1313

Sonic Measurement

Tools SummaryMeasurements: BHC LSS Array Dipole

Sonic SonicCompressional x x x x

Shear/Stoneley:Hard rock - - x xSoft rock - - - x

Computations:Porosity x x x xLithology x x x xSeismic tie in x x x x

Mechanical properties:Hard rock - - x xSoft rock - - - x

Fracture detection- - x xPermeability - - - x

1414

Sonic Measurement

Borehole Effects

As the sonic tool is measuring the time for the signal to go from the transmitter to the receiver there are two types of erroneous responses.Cycle skipping

Road noise

This is noise at the receivers that is due to the borehole environment and has nothing to do with the signal being measured.

If the signal strength is too low the detection goes to the

next peak.This means that the final transmit time will be wrong.

1515

Sonic Measurement

Borehole Effects 2

There are a number of borehole phenomena which cause these effects:

Borehole rugosity - causes the tool motion to be erratic, the signal may be distorted and give road noise or cycle skipping.

Large holes - if the borehole diameter is very large the mud signal may arrive at a receiver before the formation signal. The proper tool set-up for each condition has to be picked before the job.

This means choosing whether to centralise or excentralise the tool and the equipment to

be used.

1616

Sonic Measurement

Borehole Effects 3

Gas in the wellThe acoustic impedance of gas is very low, hence the signal will be strongly attenuated. There may be skipping.

Altered zoneThis is largely overcome by using a long spacing tool to read deeper into the formation.

CavesCan create problems in spite of compensation as they will also reduce signal amplitude.

FracturesReduce the signal amplitude especially the shear and Stoneley waves.

1717

Sonic Measurement

Porosity - 1

The porosity from the sonic slowness is different than that from the density or neutron tools.

It reacts to primary porosity only, i.e. it does not "see" the fractures or vugs.

The basic equation for sonic porosity is the Wyllie Time Average:

(((( )))) maf ttt ∆∆∆∆−−−−++++∆∆∆∆====∆∆∆∆ φφφφφφφφ 1log

maf

ma

tttt

∆∆∆∆−−−−∆∆∆∆∆∆∆∆−−−−∆∆∆∆

==== logφφφφ

1818

Sonic Measurement

porosity 2

There is another possibility for transforming slowness to porosity, called Raymer Gardner Hunt.This formula tries to take into account some

irregularities seen in the field.

The basic equation is:

A simplified version used on the Maxis is:

C is a constant, usually taken as 0.67.

(((( ))))fmac ttt ∆∆∆∆

++++∆∆∆∆−−−−====

∆∆∆∆φφφφφφφφ211

log

log

ttt

C ma

∆∆∆∆∆∆∆∆−−−−∆∆∆∆

====φφφφ

1919

Sonic Measurement

Porosity 3

This chart shows the relationship between the sonic compressional slowness and the porosity. Both the lithology and the equation must be known prior to using this chart.

2020

Sonic Measurement

Crossplots

The sonic measurements can be cross-plotted with the density or the neutron readings to give porosity and lithology information as with the density-neutron crossplot, however:

The neutron - sonic (TNPH-Dt) Has problems because there are two possible equations.

The density - sonic (Dt-RHOB) Has problems with the transforms as there is no separation between the lithology lines.

2121

Sonic Measurement

mechanical properties

2222

Sonic Measurement

Mechanical Properties and Sonics

A combination of compressional, shear and density measurements gives the rocks' dynamic elastic moduli.

These are used to obtain the formation's mechanical properties.

2323

Sonic Measurement

Mechanical Properties uses 1

Main uses of mechanical properties in soft formations are:

Sand stability evaluation, i.e.The prediction of the formation collapse under

producing conditions.

Using theoretical failure criteria it is possible to predict if the perforation will produce sand.

Well bore stability, i.e.The prediction of formation failure / collapse while drilling.This is especially relevant in deviated wells when drilling at high angles through soft rock can be problematic.The physical mechanism is similar to that of sand stability evaluation.

2424

Sonic Measurement

Mechanical Properties uses 2

The major use of mechanical properties in hard rocks is to predict how they will behave under "excess" pressure:Drilling:Will the formation fracture and the drilling mud

disappear?

Hydraulic fracturing: How much pressure will fracture the formation and how far will the fracture extend?

Experimental models are used to compute parameters such as tensile strength.

Simulations are used to predict the pressures that will "crack" the rock and lengths of fractures.

2525

Sonic Measurement

Sonic ParametersVertical resolution:

Standard (BHC, LSS, MSTC) 24"STC 36"6"DT 6"

Depth of investigation:

BHC 5"LSS-SDT 12" (12 ft spacing)

Readings in(ms/ft)

Limestone (0pu) 47.5Sandstone (0pu) 51-55Dolomite (0pu) 43.5Anhydrite 50Salt 67Shale >90Coal >120Steel (casing) 57

11

Magnetic Resonance Measurement



22


Magnetic Resonance

A typical sandstone formation consists of rock grains plus fluids.The fluids are distributed as free fluids and immobile fluidsThe grains can be large or small or mixed.There may or may not be clay minerals associated with the formationMagnetic resonance is used to analyse the porosity distribution and estimate permeability

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

Sand grainsIrreducible water

Free Fluid

33


Dephasing and T2 Relaxation Time

Z

X

Y

Z

X

Y

Z

X

Y

Alignmentalong Bo

Tipping

Dephasing

The protons are aligned in a magnetic field

The protons are tipped out of the field by 90°

The protons precess back into line. during this time they ‘dephase’ with each other.

44


Precession

The spin of the proton in a magnetic is the same as a top in a gravity field.

They spin around their axes and also in a direction around the applied field.

55


Measurement

The protons act as minute bar magnets.

In a magnetic field the generate a signal at the Larmour Frequency.

This is picked up by the receivers.

The more protons the higher the amplitude.

Hence the tool measures the number of hydrogens or the porosity

66


Spin Echoes

The pulse sequence consists of firstly a pulse to push the protons at 90° of the permanent field.Then after a time another pulse to ‘flip’ them through 180°.This continues for a set number of echoes.

77


Spin Echoes 2

The race analogy shows the runners as protons dephasing.The echo pulse reverses the field allowing the slower ‘runners’ to be in front.When they all line up again (6) a signal is generated that is picked up by the antenna.

88


T2 Decay

The gradual decay of the peaks reflects the formation signal to be measured, T2. The transverse relaxation time.The CPMG sequence eliminates spurious effects.

99


Porosities

ProducibleFluids

CapillaryBoundFluids

ClayBoundFluids

There are three ‘porosities’ in the rock system

Producible or Free Fluids - fluids that can move

Capillary Bound Fluids - fluids (usually water) stuck to the rock surface by surface tension forces.

Clay Bound Fluids - the water associated with the clay minerals.

The relaxation time for capillary bound fluids and clay bound fluids are very short.

1010


Free Fluid vs Irreducible Fluid

The Magnetic Resonance shows a difference in the time distribution for each fluid.

An empirical cut-off (for sandstone) of 33msec is used to separate the Free Fluids from the others.

1111


Pore Size

In a large pore the proton collides with the grain surface less often than in a small poreThe relaxation time is reducedThe amplitude in both cases can be the same. The porosity is the same in the large and small pores.

1/T2 = ρρρρ(S/V)T2 = Transverse relaxation time (msec)S = Surface area of poreV = Volume of poreρρρρ = Surface relaxivity

��

��

Am

plitu

de

Time msec

LargePore

��

��

Am

plitu

de Smallpore

Time msec

1212


Permeability

Porosity = 20%Permeability = 7.5 md

Porosity = 19.5%Permeability = 279 md

1313


Permeability EquationsMethod 1:

k ~ φφφφb/(S/V)2

1/T2 = ρρρρ2(S/V)

k = a (φφφφCMR)4 (T2,log)2

a ~ 4 mD/(ms)2

Method 2: Timur/Coates Equation:

k = a’ 104 (φφφφCMR)4 (FFI/BVI )2

a' ~ 1 mD

1414


CMR Wellsite Presentation

The key outputs are in track 3, the CMR porosity and the CMR free fluid Index.

Track 4 show the T2 distribution

Track 2 shows T2 and the permeability

Track 1 shows the GR.

1515


CMR Sonde Cross Section

1616


CMR Tool

Applications• Continuous permeability• Determine Swirr• Measure free fluid volume• Identify thin pay zones (6 in.)• Lithology-independent porosity• Hydrocarbon identification• Low-resistivity pay

Tool specificationsLength 14 ftWeight 300 lb.Minimum hole 6.5 in.Logging speed (sandstone) 600 ft/hrMeasurement aperture 6.0 in.Combinable YesMud resistivity No limitsMax. temperature 350°F

[175°C]

1717


CMR Example log 1

1818


CMR Example Log-2

1919


CMR Example log -3

2020


Pore sizes

10 -4 10 -3 10 -2 10 -1 10 0 10 1

10 -3 10 -2 10 -1 10 0 10 1

Popu

latio

n

T2 (s)950517-01

(V/S) pore (µm)

Berea 100 Sandstoneρ2 = 5 µm/s

(V/S)pore = ρ2 T2

Pore Shape V/S

Sphere diameter = dd/6

Tube diameter = d d/4

Sheet width = d d/2

Typical sandstone: ρ2 ~ 5 mm/s

Typical carbonate: ρ2 ~ 1.7 mm/s

11

Electrical Resistivity Logs



22


Resistivity Theory

The resistivity of a substance is a measure of its ability to impede the flow of electrical current.

Resistivity is the key to hydrocarbon saturation determination.

Porosity gives the volume of fluids but does not indicate which fluid is occupying that pore space.

33


Resistivity Theory 2

Current can only pass through the water in the formation, hence the resistivity depends

on:

Resistivity of the formation water.Amount of water present.Pore structure.

44


Resistivity Model

55


Mud Resistivities

The first resistivities encountered are those of the mud, mud filtrate and mud cake.

The surface measurements to obtain these values are often erroneous.

Key points:The samples must be identical to the mud used in the logging interval.Check answers using the Chart Book formulae.Rmf < Rm < RmcIdentify the sample source (measured or charts).

66


Salinities chart

This chart is used to compute salinities from resistivities of solution e.g. mud, and vice versa.It is also used to find the resistivities at a given temperature.

0.1

0.2

0.3

0.4

0.5

0.6

0.8

1

2

3

4

56

8

10

0.08

0.060.05

0.04

0.03

0.02

0.01

50 75 100 125 150 200 250 300 350 400

10

15

20

2530

40

50

100

150

200

250300

400

500

1000

1500

200025003000

40005000

10,000

15,00020,000

280,000

200

300

400

500

600

700

800

1000

1200

1400

1700

2000

3000

4000

5000

6000

70008000

10,000

12,000

14,000

17,000

20,000

250,000 200,000 170,000 140,000 120,000 100,00080,000 70,000 60,000 50,00040,00030,000

300,000

10 20 30 40 50 60 70 140 160 20080 90 100 120 180

ppm

Gra

ins/

gal

at 7

5ÞF

Res

istiv

ity o

f Sol

utio

n (ž

- m

)

Temperature (ÞF or ÞC)

NaC

l Con

cent

ratio

n (p

pm o

r gra

ins/

gal)

77


Old Tools

The voltage measured at M is proportional to the formation resistivity.

This electrode configuration is the Normal tool.

The distance between the A and M electrodes.The spacing determines the depth of investigation and hence the resistivity being read.

88


Normal and Lateral Tools

The Lateral device used the same principle. The difference is in electrode configuration and spacing.

Problems came from "thin beds" when the signature of the curve was used to try and find the true resistivity.

99


Old Tools 2

This figure shows some of the "signature curves" for the interpretation of lateral and normal devices in thin beds.A library exists plus the rules to extrapolate the

measured value to the true resistivity of the bed.

1010


Laterolog Principle

A current-emitting electrode, Ao, has guard electrodes positioned symmetrically on either side.Guard electrodes emit current to keep the potential difference between them and the current electrode at zero.This forces the measuring current to flow into the formation of interest.

1111


Tool Types

Various configurations have been used:

LL3The first tool of its type; single guard electrodes.

LL7Four extra electrodes added, including a feedback loop to keep the bucking current at an optimal value.

LL9Two more electrodes added, plus a Shallow Laterolog measurement. Deep and Shallow measurements were taken sequentially.

DLTSame as the LL9 but able to run deep and shallow simultaneously.

1212


borehole effects

Laterologs see the borehole environment as:

RLL = Rm + Rmc + Rxo + Rt

Rm Best measurement is in salt-saturated, lowresistivity mud. Worst readings obtained

in fresh mud. Measurements cannot be taken in oil-based mud.

Rmc Usually neglected as very small.

Rxo Depends on Rmf, needs to be known.

Rt Parameter to be measured, the higher the better.

1313


Laterolog Corrections

The log must be corrected for the effect of mud resistivity.

There are two possible conditions:Centred.Eccentred.

There is only a small difference between the two in most circumstances for the modern tool DLT-E.The old tool, DLT-B, could only be run centred.

The correction to the shallow is greater than the deep, especially in large hole sizes.

1414


Laterolog Corrections

1515


Correction Charts

1616


Bed Correction

The next correction accounts for the effects of adjacent beds which still occur despite focusing.

If the shoulder bed is highly resistive, the log has to be reduced. (Squeeze.)

If the shoulder bed is of low resistivity, the log has to be increased. (Anti-squeeze.)

LLS has a better definition because it is a shallow device.

1717


Squeeze/Anti-Squeeze

Rs is the resistivity of the bed above and below the formation of interest.

The chart is entered with the bed thickness, moving up the ratio RLLD/RS.

The correction factor is read on the y-axis.

1818


Squeeze/Anti- Squeeze

The same method is used in this chart for the Shallow Laterolog

1919


String Effect

Laterolog tools have another problem in conductive beds due to the frequency of the measurement.

In long combination tools, the LLD reads too high.

The effect has been commonly seen in low resistivity formations.

2020


Correction Example

The correction depends on the hole size, Dh, and the mud resistivity, Rm.

This correction has to be applied before any other borehole corrections.

A new chart is needed for each tool combination.

2121


TLC effectThere are two effects occurring when a Laterolog tool is run on drill pipe.

1)In TLC operations Laterologs need a special stiff bridle usually made of three sections of tool housing giving a length of 30 feet compared to the normal 80 foot bridle.

2)The total current returns to the pipe which acts as the return electrode.

The relative error is proportional to /Ra (the apparent resistivity).

This can be up to 200% at low Rt/Rm contrasts and low Rm.

2222


Example Chart

The chart is used to transform the TLC reading into the reading theoretically obtained in a vertical well with a bridle.

2323


Pseudo Geometrical Factor

Once corrected, the log can be evaluated to find Rt.

Neglecting the mud and mud cake resistivities (corrected log), the tool response equation is:

Ra = J(di)Rxo + (1-J(di))Rt

Where J(di) is the pseudo-geometrical factor which is a function of the invasion diameter, di. For large di, J(di) is large reflecting the important contribution of the invaded zone to the measurement.

2424


Depth of Investigation

The plot shows the pseudo-geometrical factor versus di for various tools.The relative depth of investigation is defined as the invasion diameter for which the invaded zone contributes to 50% of the signal (J = 0.5).The relative depth of investigation is computed from the chart.

For example, it is 35" for the LLS.

2525


Groningen Effect

The high and increasing LLD reading, associated with a flat LLS, can be caused by the presence of hydrocarbon in the formation, or by the infamous Groningen effect.

Torpedo

DLT measurepoint

LLSLLD /LLG

Induction

Resistive Bed

GroningenResponse

Laterolog

LLG

LLDincrease

Inductiondoes not react

distance totorpedo =distance

below highresistivity

Groningeneffect seen.

bridleelectrode

2626


Groningen Effect Physics

This is caused by the voltage reference (cable-torpedo) becoming non-zero.

Caused by highly resistive beds overlying the formation that is being measured.

This forces the deep current into the mud column.

2727


Solutions

The HALS/ARI tool can be corrected for Groningen effect.

There is a curve measurement by the DLT called LLG, which gives an indication of the Groningen effect.

LLG is:An LLD using a bridle electrode as return rather than the torpedo.An indicator of the presence of Groningen Effect because:

LLG equals LLD when there is no effect.LLG is affected at a different depth than LLD.

LLG is not an LLD corrected for Groningen.

2828


Laterolog Applications

Measures Rt.

Standard resistivity in high resistivity environments.

Usable in medium-to-high salinity muds.

Good results in high contrast Rt/Rm.

Fair vertical resolution (same as porosity tools).

2929


Laterolog Limits

Cannot be used in oil-based muds.

Cannot be used in air-filled holes.

Affected by the Groningen Effect in some environments.

Difficult to model.

Poor when Rxo > Rt.

3030


Modelling

It is useful to model the tool response for different conditions.

The approach of bed boundaries can be seen in deviated wells.

Unusual log responses can be checked with different model formations.

A finite element method has to be used to model Laterologs, and all resistivity tools.

This type of program is heavy on computer time.

3131


DLT Parameters

Vertical resolution: 24"

Maximum reading:LLD 40000ohm-mLLS 6000ohm-m

Minimum reading:LLD 0.2ohm-mLLS 0.2ohm-m

3232


Azimuthal Laterolog principle

The current emitting electrode is split into twelve separate electrodes.

It has 12 electrodes set equally spaced around the tool giving 12 azimuthal Laterolog readings.

These are focused to give a deep reading and a very shallow reading of the tool stand-off.

3333


Azimuthal Laterolog principle 2

There are two modes:Active mode: current is emitted from each of the electrodes.12 calibrated resistivities are output in real time.

Passive mode: no current is emitted. This is used if the resistivity is above 2 ohm-m The mud resistivity is needed to compute the resistivities.

3434


Azimuthal Laterolog corrections

The borehole correction is similar to the other Laterolog measurements. It is a function of the borehole diameter and the ratio of formation to mud resistivity.

This chart is used to make the correction. It can be done by the surface acquisition system.

3535


Azimuthal Laterolog outputs

The standard outputs of the Azimuthal Laterolog are:

Standard LLD and LLS curves.

LLhr - high resolution deep Laterolog.

12 azimuthal resistivity curves.

12 electrical stand-off measurements.

An electrical image of the borehole similar to FMS.

3636


Azimuthal Laterolog usesThe simplest use of the ARI is for deep resistivity in laminated formations. Here the tools high vertical resolution reads the correct value when the LLD averages the beds.

3737


Azimuthal Laterolog Uses 2

Another use of the ARI is fracture identification.As with any resistivity measurement it reacts to the presence of the conductive fluid (mud) in the fractures. They show up as low resistivity on each of the 12 resistivities at different depths depending on their geometry. The best indication is the image.

3838


ARI Uses 3

There are a number of other uses for this azimuthal tool:Heterogeneous formation

One or more of the resistivities will react to a heterogeneity while the others read normally. An example could be a shale lens in an oil zone. Here the resistivity will be reduced by the low resistivity shale if a standard LLD is used, however the shale will be "seen" by some of the azimuthal resistivities and the true resistivity of the oil zone can then be understood.

Horizontal wellThe ultimate heterogeneous formation. The azimuthal resistivities will be able to see the overlying and underlying formations, thecap rocks and the water table for example. Knowing where these are will greatly assist in completing the well as well as computing saturations.

Dip computationThis is an extra due to having 12 azimuthal

resistivities and the possibility of adding directional information. The output dips are not as good as a standard Dipmeter as the resolution is not as fine, however, they are sufficient for moststructural interpretations.

3939


Azimuthal Laterolog parameters

Depth of investigation LLhr close to LLD

Vertical resolution8" (in a 6" hole)

Azimuthal resolution60° for a 1" stand-off

Resistivity range0.2 - 100000 ohm-m

Mud resistivity< 2 ohm-m active mode< 5 ohm-m passive mode

4040


Microresistivity Devices

Shallow reading versions of resistivity tools; always pad-mounted.

First was the Microlog which is still in use;Second was the Micro Laterolog (MLL), replaced byProximity (PL) tool, replaced byMicroSpherically Focused Log (MSFL), replaced byMicro Cylindrical Focused Log(MCFL)

Objective is to read Rxo (Invaded Zone Resistivity) only.

Tools are focused to pass through the mud cake.

4141


Microlog Uses

Microlog is used to identify permeable zones.

If the zone of investigation is shale (no invasion), both curves read the same.If the zone is sand (with invasion), Microinverse reads mud cake plus some of the formation and Micronormal reads some mud cake plus the formation (slightly higher).We are only interested in the separation between these curves and so scales are chosen to show this and not the rest of the readings.

2" Micronormal. (A -> M2)1"x1" Microinverse. (A -> M1)(Slightly different depths of investigation).

4242


MSFL Principle

This tool uses a set of 5 electrodes which focus the signal into the invaded zone just beyond the mud cake.

4343


MSFL Borehole Corrections

In spite of its focusing, the tool still needs to be corrected for the mud cake thickness and

resistivity.The correction requires an input of mud cake thickness which is not measured directly.

It also needs the mud cake resistivity which is either measured or computed from charts.

The tool focusing has been set assuming there is always some mud cake, hence the tool

always needs some correction.

4444


Uses and Limits

Uses:Rxo measurement in water- based muds.Correction for deep resistivity tools.Sxo determination.

Limits:Rugose hole.Oil-based mud.Heavy or thick mud cake.

11

Induction logs

Induction Logs


22

Induction logs

Induction history

The idea for the tool developed out of mine detector work done by Henri Doll during the Second World War.

The objective was to measure resistivity in fresh or oil-based muds.

The first tools had 5 coils to focus the signal.

The next generation of tools employed 6 coils.

Two measurement curves were eventually developed, a medium and a deep paralleling the Laterolog's shallow and deep readings.

33

Induction logs

Induction Principle

An Induction tool uses a high frequency electromagnetic transmitter to induce a current in a ground loop of formation.

This, in turn, induces an electrical field whose magnitude is proportional to the

formation conductivity.

44

Induction logs

Geometrical Factor

In a simple model, (tool centred, homogeneous formation), the response of the tool can be

calculated as the sum of all the formation loops coaxial with the sonde.

Each signal is proportional to the conductivity and to a Geometrical Factor, Gi which depends only on the loop position with respect to the transmitter and receiver positions.

The sum of all the geometrical factors is equal to 1.

55

Induction logs

Depth of Investigation

This is equivalent to the plot seen for the laterolog.

Once again, the depth of investigation can be obtained from this plot using the same criteria.

Depth of investigation = zone contributing 50% of the signal.

66

Induction logs

Shoulder Bed Effect

To minimise the shoulder bed effect, the tool is focused using multiple coils.

In addition, the shoulder bed response is suppressed to improve the vertical resolution.

Deconvolution gives greater weight to the signal measured at the sonde centre and less

weight to the signals from either side.

The Phasor tool uses the X-signal to make a non-linear deconvolution correction.

77

Induction logs

Skin Effect

Caused by ground loops creating their own fields and interfering with the signal being measured.

The net result is a reduction in the measured conductivity.

The correction increases with increasing conductivity.

The traditional solution was to employ a booster algorithm.

The current tool uses the X-signal to make the correction.

88

Induction logs

Borehole Effects

Induction tools measure Conductivity.Induction tools measure resistivity in Parallel.Thus Induction tools see the borehole environment as:

Cm - Best readings occur in high resistivity mud, oil-based is better, fresh mud is good, salt-saturated mud is worst.

Cmc - Usually neglected as very small.

Cxo - Depends on Rmf - needs to be known.

Ct - Parameter to be measured, the higher the better.

99

Induction logs

Corrections

The tool has to be corrected for borehole effects.

Procedure

1) Compute borehole geometrical factor.2) Find additional signal due to the borehole.3) Convert log resistivity into conductivity.4) Remove borehole signal from total signal.5) Convert result back to resistivity.

This is best done in the field using either the Surface Acquisition units

It is also possible using Chart Books.

1010

Induction logs

Corrections

1111

Induction logs

Correction Charts

1212

Induction logs

Correction Charts

Procedure:Obtain the Borehole Geometrical factorEnter the value on the axis.Draw a line through the mud resistivity to obtain the hole signal..

Subtract the hole signal from the measured conductivity to obtain the corrected value

1313

Induction logs

Bed Thickness

The induction needs to be corrected for the effect of resistive or conductive shoulder beds.

After signal processing this effect is minor except in beds less than 6'.

1414

Induction logs

Enhancement

The standard Deep Induction tool has a vertical resolution of 6' to 8'.

It is impossible to improve the tool's hardware design as the measurement is "blind" at some thickness.The Medium Induction tool can "see" all thickness.

The Medium signal is used to enhance the more accurate Deep reading.

Enhanced resolution of 3'.

Very enhanced resolution of 1.5' to 2'.

A problem - the medium may be adversely affected by borehole conditions (rugosity, caving), resulting in a poor deep reading.

1515

Induction logs

LimitsCannot be used in salt-saturated muds unless in small hole sizes.

Cannot be used in high resistivity formations.

Poor in thin beds.

Poor when Rxo < Rt.

Dipping beds will affect the logs.

1616

Induction logs

Uses

Measures Rt.

Ideal in fresh or oil-based environments.

Ideal for low resistivity measurements and when Rxo > Rt.

1717

Induction logs

Modelling

As for the laterolog tool, it is useful to model the induction response to a given situation.

The Induction is simple to model in almost any case as it is based on electromagnetic theory.Programs exist for both vertical and deviated wells.

Effects such as the effect of dipping beds can be analyzed and the true resistivity of the

layer obtained.

Horizontal wells are also handled so that the response of an electromagnetic tool to a nearby cap rock or water table can be predicted.

This is important in horizontal wells where the technique called Geosteering is used to accurately position the well trajectory.

1818

Induction logs

Induction Parameters


Standard 6' to 8'Enhanced 3'Very Enhanced 1.5' to 2'

Depth of investigation:

Deep 60"

Medium 30"

1919

Induction logs

AIT principle

The tool measures 28 independent signals from 8 arrays. There is one transmitter operating at three frequencies. The in-phase (R) and the quadrature (X) signals are both measured.

The conductivities are combined using radial and depth functions.

These are software focused to give:

5 depths of investigation:10", 20", 30", 60" 90".

3 vertical resolutions: 1', 2' and 4'.

2020

Induction logs

AIT depth of investigation

The AIT has set radial depths of investigation which are not affected by changes in conductivity.

The values are taken as the point where half the signal comes from shallower levels.

In comparison to the 10", 20", 30", 60" and 90" of this tool, the medium and deep of the old tool are around 30" and 60" respectively.

2121

Induction logs

AIT Corrections

There are well defined borehole corrections to be applied to the measurement. These are made in real time by the software. The inputs required are:

Borehole cross section.Mud resistivity.Stand-off.

The tool can compute any of these from its measured signal as well as the formation resistivity. However, normal practice is to input at least two of them.

A measurement of the mud can be made with an auxiliary sonde or surface measurement.

The former is best as logs made have shown considerable heterogeneities in the mud column with depth.

A caliper tool can give the hole dimensions.

2222

Induction logs

As the AIT produces five logs with differing depths of investigation, a more realistic description of the invasion can be made.The old model is:

New model:

This model has four unknowns with the addition of a ramp profiled for the invasion.

AIT Rt-Rxo-invasion

2323

Induction logs

AIT independent model

The AIT can be displayed as an image.

The simplest image is of resistivity radial profile starting at the borehole and going out into the formation.

This image simply extrapolates the readings of the tool assigning colour classes to the resistivity level.

It is called an "independent model" because it makes no assumptions about the resistivity distribution.

2424

Induction logs

AIT saturation

To obtain a saturation image, some assumptions have to be made about the resistivity profile.

The inversion model is used to produce the parameters needed for a saturation image, Rt, Rxo and an invasion distance.

The r2 radius is taken as the limit of invasion for this calculation.

The image will then show the saturation away from the borehole, a radial profile.

This image is a more accurate picture of the invasion as long as the saturation gradient is constant with depth. The porosity is also assumed to be constant.

2525

Induction logs

AIT volumes

Variations in formation water, drilling parameters and saturation gradient obscure comparisons along a well and between wells.

A filtrate invasion profile is constructed and converted to a fluid volume by multiplying it by porosity.

Hence the AIT outputs plus the Rmf are all that is needed to compute the volume of mud filtrate, Vmf.The result is integrated with depth to give the volume of filtrate per unit depth.

2626

Induction logs

examples 2

The invaded volumes computed here show an increase with depth. The results could be used to plan sampling points or a well test.

2727

Induction logs

examples 3

The AIT logs (2' vertical resolution) read correctly in this zone giving a hydrocarbon profile.

The DIL logs are ambiguous as the SFL (electrical log) longer reading shallow because Rxo is less than Rt

90 Inch investigation(ohmm) 2000.2

0.2

0.2

0.2 2000.0

2000.0

2000.0

0.010000.0

(ohmm)

Cable tension (TENS)(LBF)

(ohmm)

SFL unaveraged (SFLU)

Medium resistivity (ILM)

(ohmm)Deep resistivity (ILD)





2828

Induction logs

AIT parameters

Radius of investigation:10" (A x 10)20" (A x 20)30" (A x 30)60" (A x 60)90" (A x 90)

Vertical resolution (x):1'2'4'

Resistivity range:0.2 - 1000ohm-m

Basic Log Interpretation

Documents

Transcript of Basic Log Interpretation