air-diving-equipment-&-accessories.pdf
-
Upload
budi-santony -
Category
Documents
-
view
212 -
download
0
Transcript of air-diving-equipment-&-accessories.pdf
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 1/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
LOW PRESSUREAIR COMPRESSOR
The Low Pressure (LP) Compressor is rated at 80 CFM @ 200 PSI, which can supply sufficient Air to
support 2 Divers during a Surface Diving Operation, and also supply Air for the Deck Decompression
Chamber (DDC). Air intake is through a 3’’ hose fitted with a filter, which is normally sited in an open
fresh air area. The compressed air is stored in a 24’’ Dia. x 72’’ long Air receiver, and then channelled
through a 3 stage filter to a manifold consisting of 1x3/4’’ and 2x3/8’’ quarter turn valves, which
distributes Air directly to the Dive panel. All pressure vessels and stages are fitted with relief valves. The
3 stages of the filter are Vortex separators, Coalescent filter and Carbon filter, all with manual drains.
The Engine exhaust is fitted with a Spark arrestor.
Specifications;
Compressor: Ingersolrand - 80CFM @ 200 PSI
Engine (If Diesel driven): Lister - 16.2 BHP
Motor (If Electric): - 12.1kW @ 440V/380V 3Ph. 50/60Hz
Weight: 1500 kg
Dimensions: L=1930mm, W=1370mm, H=2080mm
Method of Operation: Manual (Crank start) for Diesel Engine
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 2/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
SEAPROBE 200UNDERWATER THICKNESS
GAUGE
The Seaprobe 200 is a self contained battery powered thickness gauge intended for measuring
steel structure or components immersed in seawater. A particular feature of Seaprobe 200 is the
absence of user controls. In typical use, Seaprobes’s internal rechargeable battery will permit
the user to take over 2000 thickness readings before recharging is necessary. The combinationof ergonomically designed housing, large bright display and advanced measuring techniques,
results in a measurement system of high reliability and extreme simplicity.
Specifications;
System of Operation: Ultrasonic pulse-echo time-of-flight.
Range: 5mm to 99.9mm in steel.
Accuracy: +0.2mm under standard test conditions.
Display: 3 x 15mm high luminous 7 segment displays, displaying to 0.1mm.
Calibration: Calibrated for steel (5940m/sec.)Transducer: Integral with unit and self-aligning.
Battery: NiCd Rechargeable, Integral with the unit.
Additional Indicators: ‘On Charge’, ‘Battery Exhausted’, and ‘Poor Ultrasonic Coupling’all on display.
Battery Life: Over 2000 Readings between charges in normal use.Dimensions: ~360mm long, Dia. 85mm tapering to 18mm at transducer.
Weight: In air ~1.2kg/6.1kg with charger and carrying case Neutrallybuoyant in water.
Maximum working depth: 200m/650ft.Power requirement: 240/110V, 50/60Hz, 15 WattsCharging rate: Fully discharged battery can be charged in ~14hours.
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 3/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
BATHYCORROMETER
Bathycorrometer is a submersible corrosion voltmeter and integral silver/silver chloride
half-cell, incorporating digital display, for testing the corrosion condition of submerged
metallic objects. Typically, Bathycorrometer is used to check structures, pipelines,
jetties, drilling rigs, production platforms and ships hulls etc. Made from high strength
plastic, providing a robust non-corroding unit with the half-cell sited 50mm from
surface under examination. Designed for simple servicing.
Ancillary Equipment; Surface reading unit
Surface TV interface module
Underwater camera-mounted TV interface module
Specifications;
Dimensions: Instrument: Dia. 100mm x275mmHandle: 125mm Long
Weight: Instrument: 2500g in air / 850g in water
Maximum operating depth: 305m
Method of Operation: Hand-held by the Diver
Power Source: Integral Rechargeable Battery
Temperature Range: 0 to 60 Deg. C
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 4/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
NIKONOS VUNDERWATER CAMERA
This is the latest in the well proven Nikonos range of Underwater cameras and one of
the most reliable cameras for Underwater Photography giving excellent results
Specifications;
Type: Electronically controlled 35mm amphibious focal plane
shutter camera
Film: Standard 35mm Cartridge type film; 24mm x 36mm
Lenses: Nikonos bayonet mount – 15/28/35/80mm
Shutter Speeds: A (Auto) / M (Manual) speeds from 1/30 to 1/1000 secondsM 90 (Mechanical) – Mechanically controlled 1/90 seconds
B ((Bulbs) – Mechanically controlled for long exposures.
Dimensions: ~146mm (W) x 99mm (H) x 58mm (D) without lens
Weight: ~695g without lens
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 5/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
INFLATABLE RUBBERBOAT
The inflatable safety boat is an accepted part of any marine or diving operation.
Buoyancy is retained due to numerous independent compartments, each one supplied
via a Non-return valve. This boat comes fully equipped with wooden or aluminium
floor boards and oars.
Specifications;
Make: Zodiac
Type/Size: MKIII; 15.5x6.5
Power: Outboard engine rated from 25-40HP Max. Manual
crankshaft, wet cooled, wet exhaust
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 6/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
2 MAN PORTABLEDIVING STATION
The panel is built of light steel or tufnel used as a frame for 2 x Pneomo-fathometers (Depth gauges), 2 x
divers air supply, 2 x emergency HP air inlets (through an HP Reducer) to the LP system.
The panel is normally sited on 4 x HP bottles (240 cubic feet each) complete with communications and 2
x 300’umbilicals consisting of 3/8’’ gates diving hoses, ¼’’ Pneomo-fathometers, 4 x wire armoured
communications and safety line, all of which are taped together. Caribina clips secure the umbilical with
divers safety harness.
The Total unit can be moved around the deck by the vessel’s crane allowing greater flexibility to the
client in running a surface supplied diving operation.
Ancillary Equipment: Low-pressure compressor High Pressure compressor c/w storage bank
Specifications;Weight: 500 lbs. (Panel, 4 x HP bottles, 2 x Umbilicals)Dimensions: 13’x 3’x 6’
Method of operation: Manual
Power source: 12V DC/Battery
Depth rating: 165’
Panel Manufacturer: Clucas/Divex
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 7/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
DIVER’S HELMETS & MASKS
Specifications:KMB 17 KMB 18 KMB 27
Weight 24lbs (10.90kg) 11lbs (5.0 kg) 26lbs (11.81 kg)
Operating Pressure 115-225PSI Over Ambient 115-225PSI Over Ambient 115-225PSI Over Ambient
Optimum Pressure 170 PSI Over Ambient 170 PSI Over Ambient 150 PSI Over Ambient
Max. Operating
Depth
Man tested for 850 FSW To be advised Man -tested for 850 FSW by US Navy, 1600
FSW by University of Pennsylvania
Flow Requirement 4.5 SCFM 4.5 SCFM 4.5 SCFM
‘KMB’ brand Diver’s helmets and masks, now
marketed under ‘DSI’ (Diving System International),
are creations of accomplished Commercial Diver turned
designer Bill Morgan. Since incorporation of his
company ‘Kirby Morgan Corporation’ in 1960’s, he has
designed many versions of ‘KMB’ brand helmets and
masks, including the KMB 17, KMB 18 and KMB 27.
These being some of the most successful and widely
used in the diving industry world wide.
These Helmets and Masks are designed to be used with
an umbilical made up of air/gas supply hoses,
communications cable, pneumo-fathometer and safety
line, taped together to make one unit. The umbilical is
the Diver’s lifeline to the Diving Control Station (DCS),
which can be either on the surface, in a diving bell or in
a submerged habitat. The DCS is the control centre for
the Air/Gas supply, communications with the diver and
diving/work procedures.
KMB 18
The diver usually wears a tank of compressed air or gas
fitted with a suitable pressure regulator to reduce
theEpressure to about 125PSI for emergency use.
The main frame of the mask is fabricated of non-
corrosive rigid ABS plastic that will not carry an electric
charge. The pipe-work is fabricated from high quality
stainless steel, chromed brass and polished brass. The
masks and helmets are regularly inspected and parts
replaced where necessary to ensure safety.
The communications system has been redesigned to
improve the clarity irrespective of depth. The system
consists of two earphones situated in hood pockets at
either ear and the microphone is in the oral nasal at the
front of the mask.
KMB 17
The main gas/air supply from the umbilical enters the
system at the adapter and flows through the automatic
one way valve to the interior of the side block assembly.
The demand regulator provides ‘Demand’ breathing
system, which is adjustable for gas supplies from 80PSI
to about 180PSI over ambient diver pressure.
KMB 27
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 8/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
SUPPORT DIVING
EQUIPMENT
Support diving equipment consists the following;
∗ Twin or single HP scuba cylinders with back pack.
∗ Demand valve c/w contents gauge
∗ Depth gauge
∗ Life jacket
∗ Face mask
∗ Wet suit
∗
Hood and bootees∗ Knife
∗ Weight belt
∗ Snorkel
∗ Swim fins
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 9/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
AIR DIVING MODULE
Ideal unit for supporting any diving operation from Barges, Vessels or Platforms to secure
decompression and dark room facility on site.
Built around a standard 20’container, the module is an independent diving support and control unit
consisting of a Decompression chamber, Medical oxygen supply etc.
Specifications;
Dimensions: 20’x8’x8
Weight: 3 tons with all equipment
Container: Standard 20’ISO Type container.Insulation: 10cm rock wool between walls.
Ceiling/Floor: 6mm steel plate with 4mm marine ply
Outside wall: 3mm steel profiled sheet
Inside wall: 4mm Aluminium LaminateFloor: Heavy-duty anti-slip rubber with cork
Lifting: Heavy-duty 4-corner top lifting lugs
Electrical supply: Surface mounted lighting and small power with switchboard
Water supply: Cold water plumbing with inlet, Stainless steel single sink and drain
outlet.
Air Conditioning: One unit of 1.5 tons.
Built-in Equipment: 1 Twin-lock Deck Decompression Chamber
1 Set of complete dark room equipment(Optional)
1 Filing cabinet1 Heavy duty work bench
1 Shelving unit
1 Cupboard with drawers
2 Medical oxygen cylinders
1 Fire extinguisher
1 First aid box
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 10/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
DECK DECOMPRESSION
CHAMBER
The DDC is a twin lock decompression pressure vessel. The entrance or medical lock is used to access to the
main lock. The DDC is normally fitted with out with 12V telephones, Medical oxygen Scott bibs, a first aidkit and a chamber fire extinguisher. There is a service lock for transferring food and viewing ports with
external lighting. The air and medical oxygen is controlled from a panel mounted on the outside of the DDCwhere the operator can monitor the diver and supply air and medical oxygen required during decompression
or therapeutic treatment.
The DDC is normally installed in a standard 20’air-conditioned container c/w door, windows, 240V AC
power distribution panel and workbench. Optionally, Dark equipment for developing 35mm colour or black
film on site too is provided.
Ancillary Equipment;
∗ Low pressure air compressor
∗ High pressure air bank
∗ High pressure air bank
∗ Medical oxygen bank
Specifications;
Dimensions: 20’x 8’x 8’ (Container)
12’x 4.5’x 5.5’ (Chamber)
Weight: 6000 lbs.Power source: 12V DC Battery
Method of operation: Manual
Depth rating: 165’
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 11/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
SCUBA REPLACEMENT
Scuba replacement is ideal for anchor spot checks; start up/lay down head during
pipe laying operations, crossing and as built in deep waters. It can accommodateup to 6 divers and supervisor in one trip.
It is equipped with one mobile diving panel for 2 divers, three 50 litre air cylinders
of 200 bar rating, of which two for operating and one standby, (5 hours
continuous air supply for one diver at 20 metres), one surface demand umbilical
complete with KM18-27and communication box. The boat is powered by a 40 HP
outboard motor with remote control.
The payload is approximately 1500kg.
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 12/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
HIGH PRESSURE
AIR COMPRESSOR
The Bauer High Pressure Compressor KA16, KAZU compressor is a complete
unit for filling tanks to a maximum pressure of 300 bars through common
manifold c/w pressure gauges and HP hoses fitted with ‘A’ clamps. It can charge
one air cylinder from 0 bars to 0.35 minutes. Either a diesel engine or an electric
motor drives the compressor.
Specifications;
Dimensions: 53’’ Long x 31’’ Wide x 44’’ High
Weight: 290 kg.
No. Of Cylinders: 4
Capacity: 500 litres per minute
Types: K 16-15 DieselK 18-18 Electric
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 13/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
HP AIR STORAGE BANKS
The HP Banks are used to either supply HP air to dive panel through ½’’ HP whips or
LP air to DDC through high flow regulators.
Cylinders are interconnected with each cylinder having an isolating valve. The
interconnections are connected to 2 main inlet/outlet lines fitted again with isolating
valves.
Specifications;
Cylinder capacity: 50 litres each
Dimensions and weights:
No. of Cylinders Size Weight
9 5’6’’x3’x 4’ 750kg
12 6’x4’x4’ 950kg
16 6’9’’x4’x 4’ 1000kg
20 6’9’’x4’x4’ 1600kg
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 14/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab EmiratesTel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
UNDERWATER VIDEO
SYSTEM
The ‘Bowtech’ BP-DVIS, Diver Video Inspection System is a portable control station for operation, viewing
and recording of underwater colour or monochrome video cameras together with intensity control of
underwater lamp.
The control station is housed in a marine grade transport container manufactured from high quality plywood,pressure bonded to tough laminate, riveted to external angle frame using waterproof rivets.
The system consists of BP-L3c colour camera, underwater lamp, diver pistol grip or helmet mounting kit,
umbilical and surface control station.
The system can be powered from 240VAC mains or from a local 12VDC battery pack. A video overlay unit
and audio recording from the diver can be added as an option.
Specifications;
Dimensions: 46cm Wide, 53cm Deep, 45cm High (Container)
Weight: 35.5kg.
Power supply: 240VAC or 12 VDC-15 Amps.Operating Temperature: -10 Deg. C to +40 Deg. C
Camera:
Resolution, Horizontal: 320 TV Lines
Light Sensitivity: 5 lux (Faceplate)Sensor Type: ¼’’ CCD
Signal to Noise ratio: >46db (AGC off)
Lens: 2.9mm f2.0
Iris: electronic Shutter1/50th~
Focus: 100,000th Sec.
Angle of View in water: Fixed 100mm
~Infinity..
70 Deg Diagonal
Window: Quartz glass
Scanning: 625 Line 50 Hz PAL525 Line 60 Hz NTSC
Power: 10.5VDC to 24.0VDC
Current: 100ma Maximum
Composite Video Output: 1.0 V pk-pkWater Depth: 3000m
Weight: 500g in Air, 400g in WaterHousing: Anodised Aluminium
8/10/2019 air-diving-equipment-&-accessories.pdf
http://slidepdf.com/reader/full/air-diving-equipment-accessoriespdf 15/15
CCC (Underwater Engineering) S.A.L.
P.O.Box 224, Abu Dhabi, United Arab Emirates
Tel. 00971 2 5553656, Telefax 00971 2 5553641, Telex 23441 CCCUWE, e-mail address: [email protected]
‘HELLE’ DIVER PHONES
GAS RADIO AIR RADIO
A completely self-contained unit that provides two-wire communication between the operator and one or two divers.
The Model 3220 provides unusually good sound quality, even in a helium atmosphere, because of a broader
frequency response of 300Hz to 12kHz, which is greater than the 300Hz 3kHz typically used in voice communicationsystems.
For easy hook-up, the two wires from each of the divers speakers/microphones are connected to binding posts on the
front panel. The speakers function as speakers and microphones for both divers’ and surface units. When two divers
are connected in this manner, a three-way conversation is possible; the operator can talk to each diver individually orboth simultaneously. The divers can also talk to each other directly.
A Press-to-talk switch, a diver speaker selector and two cross-talk switches enable the surface operator to control allmodes of operation. Separate volume controls adjust the output of both the surface unit’s and divers’
speaker/microphones, providing the divers with more or less volume as conditions demand. A full six watts audioallows easy listening even at noisy work sites.
An important safety feature is the input and output transformers that electrically isolate the divers’ cables from powerleads. Internal shielding suppresses interference from ignition systems, radio transmission and generating equipment.
A record jack on the front panel enables the tender to record both sides of all conversations.
An optional feature is the Remote Jack, which will allow the tender to remotely operate the Press-to-talk switch up to250 feet away from the unit.
Specifications;
Dimensions: 168mm High, 416mm Wide, 213mm DeepWeight: 6.8kg.
Power supply: Two 6V Lantern Batteries or 12 external source
Battery Life: 20 Hours or more continuousFrequency response: 300Hz to 12kHz
Power output: up to 6wattsCabinet Material: ABS Plastic, Anodised aluminium front panel